Starting with the upcoming Rust 1.86.0 (to be released 2025-04-03),
Clippy warns:
error: manually reimplementing `div_ceil`
--> drivers/gpu/drm/drm_panic_qr.rs:548:26
|
548 | let pad_offset = (offset + 7) / 8;
| ^^^^^^^^^^^^^^^^ help: consider using `.div_ceil()`: `offset.div_ceil(8)`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#manual_div_ceil
And similarly for `stride`. Thus apply the suggestion to both.
The behavior (and thus codegen) is not exactly equivalent [1][2], since
`div_ceil()` returns the right value for the values that currently
would overflow.
We currently call intel_set_cdclk_post_plane_update() far
too early. When pipes are active during the reprogramming
the current spot only works for the cd2x divider update
case, as that is synchronize to the pipe's vblank. Squashing
and crawling are not synchronized in any way, so doing the
programming while the pipes/planes are potentially still using
the old hardware state could lead to underruns.
Move the post plane reprgramming to a spot where we know
that the pipes/planes have switched over the new hardware
state.
When the size of a transfer exceeds the size of the FIFO (32 bytes), RX
overflows will be generated and receive data will be corrupted and
warnings will be produced. For example, here's an error generated by a
transfer of 36 bytes:
The driver is currently split between handling receiving in the
interrupt handler, and sending outside of it. Move all handling out of
the interrupt handling, and explicitly link the number of bytes read of
of the RX FIFO to the number written into the TX one. This both resolves
the overflow problems as well as simplifying the flow of the driver.
CC: stable@vger.kernel.org Fixes: 9ac8d17694b6 ("spi: add support for microchip fpga spi controllers") Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://patch.msgid.link/20250303-veal-snooper-712c1dfad336@wendy Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, load_microcode_amd() iterates over all NUMA nodes, retrieves their
CPU masks and unconditionally accesses per-CPU data for the first CPU of each
mask.
According to Documentation/admin-guide/mm/numaperf.rst:
"Some memory may share the same node as a CPU, and others are provided as
memory only nodes."
Therefore, some node CPU masks may be empty and wouldn't have a "first CPU".
On a machine with far memory (and therefore CPU-less NUMA nodes):
- cpumask_of_node(nid) is 0
- cpumask_first(0) is CONFIG_NR_CPUS
- cpu_data(CONFIG_NR_CPUS) accesses the cpu_info per-CPU array at an
index that is 1 out of bounds
This does not have any security implications since flashing microcode is
a privileged operation but I believe this has reliability implications by
potentially corrupting memory while flashing a microcode update.
When booting with CONFIG_UBSAN_BOUNDS=y on an AMD machine that flashes
a microcode update. I get the following splat:
UBSAN: array-index-out-of-bounds in arch/x86/kernel/cpu/microcode/amd.c:X:Y
index 512 is out of range for type 'unsigned long[512]'
[...]
Call Trace:
dump_stack
__ubsan_handle_out_of_bounds
load_microcode_amd
request_microcode_amd
reload_store
kernfs_fop_write_iter
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
Change the loop to go over only NUMA nodes which have CPUs before determining
whether the first CPU on the respective node needs microcode update.
According to [1], `NonNull<T>` and `#[repr(transparent)]` wrapper types
such as our custom `KBox<T>` have the null pointer optimization only if
`T: Sized`. Thus remove the `Zeroable` implementation for the unsized
case.
Link: https://doc.rust-lang.org/stable/std/option/index.html#representation Reported-by: Alice Ryhl <aliceryhl@google.com> Closes: https://lore.kernel.org/rust-for-linux/CAH5fLghL+qzrD8KiCF1V3vf2YcC6aWySzkmaE2Zzrnh1gKj-hw@mail.gmail.com/ Cc: stable@vger.kernel.org # v6.12+ (a custom patch will be needed for 6.6.y) Fixes: 38cde0bd7b67 ("rust: init: add `Zeroable` trait and `init::zeroed` function") Signed-off-by: Benno Lossin <benno.lossin@proton.me> Reviewed-by: Alice Ryhl <aliceryhl@google.com> Reviewed-by: Andreas Hindborg <a.hindborg@kernel.org> Link: https://lore.kernel.org/r/20250305132836.2145476-1-benno.lossin@proton.me
[ Added Closes tag and moved up the Reported-by one. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel cannot currently self-parse BTF containing Rust debug
information. pahole uses the language of the CU to determine whether to
filter out debug information when generating the BTF. When LTO is
enabled, Rust code can cross CU boundaries, resulting in Rust debug
information in CUs labeled as C. This results in a system which cannot
parse its own BTF.
Signed-off-by: Matthew Maurer <mmaurer@google.com> Cc: stable@vger.kernel.org Fixes: c1177979af9c ("btf, scripts: Exclude Rust CUs with pahole") Link: https://lore.kernel.org/r/20250108-rust-btf-lto-incompat-v1-1-60243ff6d820@google.com Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISO C's `aligned_alloc` is partially implementation-defined; on some
systems it inherits stricter requirements from POSIX's `posix_memalign`.
This causes the call added in commit dd09538fb409 ("rust: alloc:
implement `Cmalloc` in module allocator_test") to fail on macOS because
it doesn't meet the requirements of `posix_memalign`.
Adjust the call to meet the POSIX requirement and add a comment. This
fixes failures in `make rusttest` on macOS.
Acked-by: Danilo Krummrich <dakr@kernel.org> Cc: stable@vger.kernel.org Fixes: dd09538fb409 ("rust: alloc: implement `Cmalloc` in module allocator_test") Signed-off-by: Tamir Duberstein <tamird@gmail.com> Reviewed-by: Gary Guo <gary@garyguo.net> Link: https://lore.kernel.org/r/20250213-aligned-alloc-v7-1-d2a2d0be164b@gmail.com
[ Added Cc: stable. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 392e34b6bc22 ("kbuild: rust: remove the `alloc` crate and
`GlobalAlloc`") we stopped using the upstream `alloc` crate.
Thus remove a few leftover mentions treewide.
Cc: stable@vger.kernel.org # Also to 6.12.y after the `alloc` backport lands Fixes: 392e34b6bc22 ("kbuild: rust: remove the `alloc` crate and `GlobalAlloc`") Reviewed-by: Danilo Krummrich <dakr@kernel.org> Reviewed-by: Andreas Hindborg <a.hindborg@kernel.org> Link: https://lore.kernel.org/r/20250303171030.1081134-1-ojeda@kernel.org Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, dynamically allocated LockCLassKeys can be used from the Rust
side without having them registered. This is a soundness issue, so
remove them.
The device id entries for Telit FN990B ended up matching only on the
interface protocol. While this works, the protocol is qualified by the
interface class (and subclass) which should have been included.
Switch to matching using USB_DEVICE_AND_INTERFACE_INFO() while keeping
the entries sorted also by protocol for consistency.
The Altera USB Blaster 3, available as both a cable and an on-board
solution, is primarily used for programming and debugging FPGAs.
It interfaces with host software such as Quartus Programmer,
System Console, SignalTap, and Nios Debugger. The device utilizes
either an FT2232 or FT4232 chip.
Enabling the support for various configurations of the on-board
USB Blaster 3 by including the appropriate VID/PID pairs,
allowing it to function as a serial device via ftdi_sio.
Note that this check-in does not include support for the
cable solution, as it does not support UART functionality.
The supported configurations are determined by the
hardware design and include:
1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART
2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART
3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART
4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART
5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART
6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART
7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART
8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART
These configurations allow for flexibility in how the USB Blaster 3 is
used, depending on the specific needs of the hardware design.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some older Clevo barebones have problems like no or laggy keyboard after
resume or boot which can be fixed with the SERIO_QUIRK_FORCENORESTORE
quirk.
We could not activly retest these devices because we no longer have them in
our archive, but based on the other old Clevo barebones we tested where the
new quirk had the same or a better behaviour I think it would be good to
apply it on these too.
Some older Clevo barebones have problems like no or laggy keyboard after
resume or boot which can be fixed with the SERIO_QUIRK_FORCENORESTORE
quirk.
While the old quirk combination did not show negative effects on these
devices specifically, the new quirk works just as well and seems more
stable in general.
Some older Clevo barebones have problems like no or laggy keyboard after
resume or boot which can be fixed with the SERIO_QUIRK_FORCENORESTORE
quirk.
The PB71RD keyboard is sometimes laggy after resume and the PC70DR, PB51RF,
P640RE, and PCX0DX_GN20 keyboard is sometimes unresponsive after resume.
This quirk fixes that.
The QH controller is actually the controller of the Legion Go S, with
the manufacturer string wch.cn and product name Legion Go S in its
USB descriptor. A cursory lookup of the VID reveals the same.
TECNO Pocket Go is a kickstarter handheld by manufacturer TECNO Mobile.
It poses a unique feature: it does not have a display. Instead, the
handheld is essentially a pc in a controller. As customary, it has an
xpad endpoint, a keyboard endpoint, and a vendor endpoint for its
vendor software.
ZOTAC Gaming Zone is ZOTAC's 2024 handheld release. As it is common
with these handhelds, it uses a hybrid USB device with an xpad
endpoint, a keyboard endpoint, and a vendor-specific endpoint for
RGB control et al.
Some register groups reserve a byte at the end of their continuous
address space. Depending on the variant of silicon, this field may
share the same memory space as the lower byte of the system status
register (0x10).
In these cases, caching the reserved byte and writing it later may
effectively reset the device depending on what happened in between
the read and write operations.
Solve this problem by avoiding any access to this last byte within
offending register groups. This method replaces a workaround which
attempted to write the reserved byte with up-to-date contents, but
left a small window in which updates by the device could have been
clobbered.
Now that the driver does not touch these reserved bytes, the order
in which the device's registers are written no longer matters, and
they can be written in their natural order. The new method is also
much more generic, and can be more easily extended to new variants
of silicon with different register maps.
As part of this change, the register read and write functions must
be gently updated to support byte access instead of word access.
commit 767d83361aaa ("Input: ads7846 - Convert to use software nodes")
has simplified the code but accidentially converted a devm_gpiod_get()
to gpiod_get(). This leaves the gpio reserved on module remove and the
driver can no longer be loaded again.
As per dt-bindings the property is called vddio-supply, so use the
correct name in the driver instead of iovdd. The datasheet also calls
the supply 'VDDIO'.
Fixes: 44362279bdd4 ("Input: add core support for Goodix Berlin Touchscreen IC") Cc: stable@vger.kernel.org Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20250103-goodix-berlin-fixes-v1-2-b014737b08b2@fairphone.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WSL socket, fifo, char and block devices have empty reparse buffer.
Validate the length of the reparse buffer.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: cad3fc0a4c8c ("cifs: Throw -EOPNOTSUPP error on unsupported reparse point type from parse_reparse_point()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Lets callers distinguish why the vhost task creation failed. No one
currently cares why it failed, so no real runtime change from this
patch, but that will not be the case for long.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Message-ID: <20250227230631.303431-2-kbusch@meta.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Device mapper bioset often has big bio_slab size, which can be more than
1000, then 8byte can't hold the slab name any more, cause the kmem_cache
allocation warning of 'kmem_cache of name 'bio-108' already exists'.
Fix the warning by extending bio_slab->name to 12 bytes, but fix output
of /proc/slabinfo
* From an interrupt, where raised softirqs are handled on IRQ exit
* From a softirq disabled section, where raised softirqs are handled on
the next call to local_bh_enable().
* From a softirq handler, where raised softirqs are handled on the next
round in do_softirq(), or further deferred to a dedicated kthread.
Other bare tasks context may end up ignoring the raised NET_RX vector
until the next random softirq handling opportunity, which may not
happen before a while if the CPU goes idle afterwards with the tick
stopped.
Such "misuses" have been detected on several places thanks to messages
of the kind:
"NOHZ tick-stop error: local softirq work is pending, handler #08!!!"
019edd01d174 ("ath10k: sdio: Add missing BH locking around napi_schdule()") 330068589389 ("idpf: disable local BH when scheduling napi for marker packets") e3d5d70cb483 ("net: lan78xx: fix "softirq work is pending" error") e55c27ed9ccf ("mt76: mt7615: add missing bh-disable around rx napi schedule") c0182aa98570 ("mt76: mt7915: add missing bh-disable around tx napi enable/schedule") 970be1dff26d ("mt76: disable BH around napi_schedule() calls") 019edd01d174 ("ath10k: sdio: Add missing BH locking around napi_schdule()") 30bfec4fec59 ("can: rx-offload: can_rx_offload_threaded_irq_finish(): add new function to be called from threaded interrupt") e63052a5dd3c ("mlx5e: add add missing BH locking around napi_schdule()") 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule") bd4ce941c8d5 ("mlx4: Invoke softirqs after napi_reschedule") 8cf699ec849f ("mlx4: do not call napi_schedule() without care") ec13ee80145c ("virtio_net: invoke softirqs after __napi_schedule")
This shows that relying on the caller to arrange a proper context for
the softirqs to be handled while calling napi_schedule() is very fragile
and error prone. Also fixing them can also prove challenging if the
caller may be called from different kinds of contexts.
Therefore fix this from napi_schedule() itself with waking up ksoftirqd
when softirqs are raised from task contexts.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Reported-by: Jakub Kicinski <kuba@kernel.org> Reported-by: Francois Romieu <romieu@fr.zoreil.com> Closes: https://lore.kernel.org/lkml/354a2690-9bbf-4ccb-8769-fa94707a9340@molgen.mpg.de/ Cc: Breno Leitao <leitao@debian.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250223221708.27130-1-frederic@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When both of X86_LOCAL_APIC and X86_THERMAL_VECTOR are disabled,
the irq tracing produces a W=1 build warning for the tracing
definitions:
In file included from include/trace/trace_events.h:27,
from include/trace/define_trace.h:113,
from arch/x86/include/asm/trace/irq_vectors.h:383,
from arch/x86/kernel/irq.c:29:
include/trace/stages/init.h:2:23: error: 'str__irq_vectors__trace_system_name' defined but not used [-Werror=unused-const-variable=]
Make the tracepoints conditional on the same symbosl that guard
their usage.
There are cases when it is useful to use both ACPI and DTB provided by
the bootloader, however in such cases we should make sure to prevent
conflicts between the two. Namely, don't try to use DTB for SMP setup
if ACPI is enabled.
Precisely, this prevents at least:
- incorrectly calling register_lapic_address(APIC_DEFAULT_PHYS_BASE)
after the LAPIC was already successfully enumerated via ACPI, causing
noisy kernel warnings and probably potential real issues as well
- failed IOAPIC setup in the case when IOAPIC is enumerated via mptable
instead of ACPI (e.g. with acpi=noirq), due to
mpparse_parse_smp_config() overridden by x86_dtb_parse_smp_config()
Freqency mode is the current default mode of Linux perf. A period of 1 is
used as a starting period. The period is auto-adjusted on each tick or an
overflow, to meet the frequency target.
The start period of 1 is too low and may trigger some issues:
- Many HWs do not support period 1 well.
https://lore.kernel.org/lkml/875xs2oh69.ffs@tglx/
- For an event that occurs frequently, period 1 is too far away from the
real period. Lots of samples are generated at the beginning.
The distribution of samples may not be even.
- A low starting period for frequently occurring events also challenges
virtualization, which has a longer path to handle a PMI.
The limit_period value only checks the minimum acceptable value for HW.
It cannot be used to set the start period, because some events may
need a very low period. The limit_period cannot be set too high. It
doesn't help with the events that occur frequently.
It's hard to find a universal starting period for all events. The idea
implemented by this patch is to only give an estimate for the popular
HW and HW cache events. For the rest of the events, start from the lowest
possible recommended value.
Currently, we assume that the PCH DMIC pins are pin-muxed with SoundWire
links. However, we do see a HW design that use PCH DMIC along with 3
SoundWire links. Remove the check now.
With this change the PCM DMIC will be presented if it is reported by the
BIOS irrespective of whether there are SDW links present or not.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://patch.msgid.link/20250225093716.67240-2-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some tools like KGraphViewer interpret the "ON" nodes not having an
explicitly set fill colour as them being entirely black, which obscures
the text on them and looks funny. In fact, I thought they were off for
the longest time. Comparing to the output of the `dot` tool, I assume
they are supposed to be white.
Instead of speclawyering over who's in the wrong and must immediately
atone for their wickedness at the altar of RFC2119, just be explicit
about it, set the fillcolor to white, and nobody gets confused.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Link: https://patch.msgid.link/20250221-dapm-graph-node-colour-v1-1-514ed0aa7069@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fuse allows the value of a symlink to change and this property is exploited
by some filesystems (e.g. CVMFS).
It has been observed, that sometimes after changing the symlink contents,
the value is truncated to the old size.
This is caused by fuse_getattr() racing with fuse_reverse_inval_inode().
fuse_reverse_inval_inode() updates the fuse_inode's attr_version, which
results in fuse_change_attributes() exiting before updating the cached
attributes
This is okay, as the cached attributes remain invalid and the next call to
fuse_change_attributes() will likely update the inode with the correct
values.
The reason this causes problems is that cached symlinks will be
returned through page_get_link(), which truncates the symlink to
inode->i_size. This is correct for filesystems that don't mutate
symlinks, but in this case it causes bad behavior.
The solution is to just remove this truncation. This can cause a
regression in a filesystem that relies on supplying a symlink larger than
the file size, but this is unlikely. If that happens we'd need to make
this behavior conditional.
Reported-by: Laura Promberger <laura.promberger@cern.ch> Tested-by: Sam Lewis <samclewis@google.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Link: https://lore.kernel.org/r/20250220100258.793363-1-mszeredi@redhat.com Reviewed-by: Bernd Schubert <bschubert@ddn.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.
This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.
The fabric transports and also the PCI transport are not entering the
LIVE state from NEW or RESETTING. This makes the state machine more
restrictive and allows to catch not supported state transitions, e.g.
directly switching from RESETTING to LIVE.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Daniel Wagner <wagi@kernel.org> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the C11 standard (ISO/IEC 9899:2011, 6.5.7):
"If E1 has a signed type and E1 x 2^E2 is not representable in the result
type, the behavior is undefined."
Shifting 1 << 31 causes signed integer overflow, which leads to undefined
behavior.
Fix this by explicitly using '1U << 31' to ensure the shift operates on
an unsigned type, avoiding undefined behavior.
If the reparse point was not handled (indicated by the -EOPNOTSUPP from
ops->parse_reparse_point() call) but reparse tag is of type name surrogate
directory type, then treat is as a new mount point.
Name surrogate reparse point represents another named entity in the system.
From SMB client point of view, this another entity is resolved on the SMB
server, and server serves its content automatically. Therefore from Linux
client point of view, this name surrogate reparse point of directory type
crosses mount point.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The queue state checking in nvmet_rdma_recv_done is not in queue state
lock.Queue state can transfer to LIVE in cm establish handler between
state checking and state lock here, cause a silent drop of nvme connect
cmd.
Recheck queue state whether in LIVE state in state lock to prevent this
issue.
Signed-off-by: Ruozhu Li <david.li@jaguarmicro.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order for two Acer FA100 SSDs to work in one PC (in the case of
myself, a Lenovo Legion T5 28IMB05), and not show one drive and not
the other, and sometimes mix up what drive shows up (randomly), these
two lines of code need to be added, and then both of the SSDs will
show up and not conflict when booting off of one of them. If you boot
up your computer with both SSDs installed without this patch, you may
also randomly get into a kernel panic (if the initrd is not set up) or
stuck in the initrd "/init" process, it is set up, however, if you do
apply this patch, there should not be problems with booting or seeing
both contents of the drive. Tested with the btrfs filesystem with a
RAID configuration of having the root drive '/' combined to make two
256GB Acer FA100 SSDs become 512GB in total storage.
When io_uring submission goes async for the first time on a given task,
we'll try to create a worker thread to handle the submission. Creating
this worker thread can fail due to various transient conditions, such as
an outstanding signal in the forking thread, so we have retry logic with
a limit of 3 retries. However, this retry logic appears to be too
aggressive/fast - we've observed a thread blowing through the retry
limit while having the same outstanding signal the whole time. Here's an
excerpt of some tracing that demonstrates the issue:
First, signal 26 is generated for the process. It ends up getting routed
to thread 92942.
And then we immediately switch back to the original task to try creating
a worker again. This fails, because the original task still hasn't
handled its signal.
The pattern repeats another couple times until we blow through the retry
counter, at which point we give up. All outstanding work is canceled,
and the io_uring command which triggered all this is failed with
ECANCELED:
Try to address this issue by adding a small scaling delay when retrying
worker creation. This should give the forking thread time to handle its
signal in the above case. This isn't a particularly satisfying solution,
as sufficiently paradoxical scheduling would still have us hitting the
same issue, and I'm open to suggestions for something better. But this
is likely to prevent this (already rare) issue from hitting in practice.
When using the Qualcomm X55 modem on the ThinkPad X13s, the kernel log is
constantly being filled with errors related to a "sequence number glitch",
e.g.:
[ 1903.284538] sequence number glitch prev=16 curr=0
[ 1913.812205] sequence number glitch prev=50 curr=0
[ 1923.698219] sequence number glitch prev=142 curr=0
[ 2029.248276] sequence number glitch prev=1555 curr=0
[ 2046.333059] sequence number glitch prev=70 curr=0
[ 2076.520067] sequence number glitch prev=272 curr=0
[ 2158.704202] sequence number glitch prev=2655 curr=0
[ 2218.530776] sequence number glitch prev=2349 curr=0
[ 2225.579092] sequence number glitch prev=6 curr=0
Internet connectivity is working fine, so this error seems harmless. It
looks like modem does not preserve the sequence number when entering low
power state; the amount of errors depends on how actively the modem is
being used.
A similar issue has also been seen on USB-based MBIM modems [1]. However,
in cdc_ncm.c the "sequence number glitch" message is a debug message
instead of an error. Apply the same to the mhi_wwan_mbim.c driver to
silence these errors when using the modem.
In some cases, e.g. during resuming from suspend, there is a possibility
that some IPC reply messages get received by the host while the DSP
firmware has not yet reached the complete boot state.
Detect when this happens and do not attempt to process the unexpected
replies from DSP. Instead, provide proper debugging support.
Stress testing resume from suspend on Valve Steam Deck OLED (Galileo)
revealed that the DSP firmware could enter an unrecoverable faulty
state, where the kernel ring buffer is flooded with IPC related error
messages:
[ +0.017002] snd_sof_amd_vangogh 0000:04:00.5: acp_sof_ipc_send_msg: Failed to acquire HW lock
[ +0.000054] snd_sof_amd_vangogh 0000:04:00.5: ipc3_tx_msg_unlocked: ipc message send for 0x30100000 failed: -22
[ +0.000005] snd_sof_amd_vangogh 0000:04:00.5: Failed to setup widget PIPELINE.6.ACPHS1.IN
[ +0.000004] snd_sof_amd_vangogh 0000:04:00.5: Failed to restore pipeline after resume -22
[ +0.000003] snd_sof_amd_vangogh 0000:04:00.5: PM: dpm_run_callback(): pci_pm_resume returns -22
[ +0.000009] snd_sof_amd_vangogh 0000:04:00.5: PM: failed to resume async: error -22
[...]
[ +0.002582] PM: suspend exit
[ +0.065085] snd_sof_amd_vangogh 0000:04:00.5: ipc tx error for 0x30130000 (msg/reply size: 12/0): -22
[ +0.000499] snd_sof_amd_vangogh 0000:04:00.5: error: failed widget list set up for pcm 1 dir 0
[ +0.000011] snd_sof_amd_vangogh 0000:04:00.5: error: set pcm hw_params after resume
[ +0.000006] snd_sof_amd_vangogh 0000:04:00.5: ASoC: error at snd_soc_pcm_component_prepare on 0000:04:00.5: -22
[...]
A system reboot would be necessary to restore the speakers
functionality.
However, by delaying a bit any host to DSP transmission right after
the firmware boot completed, the issue could not be reproduced anymore
and sound continued to work flawlessly even after performing thousands
of suspend/resume cycles.
Introduce the post_fw_run_delay ACP quirk to allow providing the
aforementioned delay via the snd_sof_dsp_ops->post_fw_run() callback for
the affected devices.
In enviornment without KMOD requesting module may fail to load
snd-hda-codec-hdmi, resulting in HDMI audio not usable.
Add softdep to loading HDMI codec module first to ensure we can load it
correctly.
Signed-off-by: Terry Cheong <htcheong@chromium.org> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Johny Lin <lpg76627@gmail.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://patch.msgid.link/20250206094723.18013-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using `fsleep` instead of `msleep` resolves some customer complaints
regarding the precision of up/down DAPM event timing. `fsleep()`
automatically selects the appropriate sleep function, making the delay
time more predictable.
Current rsnd driver supports Synchronous SRC Mode, but HW allow to update
rate only within 1% from current rate. Adjust to it.
Becially, this feature is used to fine-tune subtle difference that occur
during sampling rate conversion in SRC. So, it should be called within 1%
margin of rate difference.
If there was difference over 1%, it will apply with 1% increments by using
loop without indicating error message.
rsnd_kctrl_accept_runtime() (1) is used for runtime convert rate
(= Synchronous SRC Mode). Now, rsnd driver has 2 kctrls for it
(A): "SRC Out Rate Switch"
(B): "SRC Out Rate" // it calls (1)
(A): can be called anytime
(B): can be called only runtime, and will indicate warning if it was used
at non-runtime.
To use runtime convert rate (= Synchronous SRC Mode), user might uses
command in below order.
(X): > amixer set "SRC Out Rate" on
> aplay xxx.wav &
(Y): > amixer set "SRC Out Rate" 48010 // convert rate to 48010Hz
(Y): calls B
(X): calls both A and B.
In this case, when user calls (X), it calls both (A) and (B), but it is not
yet start running. So, (B) will indicate warning.
This warning was added by commit b5c088689847 ("ASoC: rsnd: add warning
message to rsnd_kctrl_accept_runtime()"), but the message sounds like the
operation was not correct. Let's update warning message.
The message is very SRC specific, implement it in src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://patch.msgid.link/8734gt2qed.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The internal mic boost on the Positivo ARN50 is too high.
Fix this by applying the ALC269_FIXUP_LIMIT_INT_MIC_BOOST fixup to the machine
to limit the gain.
commit 90de551c1bf ("ASoC: simple-card-utils.c: enable multi Component
support") added muiti Component support, but was missing to add
dlc->of_node. Because of it, Sound device list will indicates strange
name if it was DPCM connection and driver supports dai->driver->dai_args,
like below
Add lookup of PCI subsystem vendor:device ID to find a quirk.
The subsystem ID (SSID) is part of the PCI specification to uniquely
identify a particular system-specific implementation of a hardware
device.
Unlike DMI information, it identifies the sound hardware itself, rather
than a specific model of PC. SSID can be more reliable and stable than
DMI strings, and is preferred by some vendors as the way to identify
the actual sound hardware.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://patch.msgid.link/20250204053943.93596-2-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The find_preferred_mode() functions takes the mode_config mutex, but due
to the order most tests have, is called with the crtc_ww_class_mutex
taken. This raises a warning for a circular dependency when running the
tests with lockdep.
Reorder the tests to call find_preferred_mode before the acquire context
has been created to avoid the issue.
The tests all deviate slightly in how they assign their local pointers
to DRM entities. This makes refactoring pretty difficult, so let's just
move the assignment as soon as the entities are allocated.
After the hci sync command releases l2cap_conn, the hci receive data work
queue references the released l2cap_conn when sending to the upper layer.
Add hci dev lock to the hci receive data work queue to synchronize the two.
[1]
BUG: KASAN: slab-use-after-free in l2cap_send_cmd+0x187/0x8d0 net/bluetooth/l2cap_core.c:954
Read of size 8 at addr ffff8880271a4000 by task kworker/u9:2/5837
Reported-by: syzbot+31c2f641b850a348a734@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=31c2f641b850a348a734 Tested-by: syzbot+31c2f641b850a348a734@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the time being, the amu_fie_cpus cpumask is being exclusively used
by the AMU-related internals of FIE support and is guaranteed to be
valid on every access currently made. Still the mask is not being
invalidated on one of the error handling code paths, which leaves
a soft spot with theoretical risk of UAF for CPUMASK_OFFSTACK cases.
To make things sound, delay allocating said cpumask
(for CPUMASK_OFFSTACK) avoiding otherwise nasty sanitising case failing
to register the cpufreq policy notifications.
Signed-off-by: Beata Michalska <beata.michalska@arm.com> Reviewed-by: Prasanna Kumar T S M <ptsm@linux.microsoft.com> Reviewed-by: Sumit Gupta <sumitg@nvidia.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Link: https://lore.kernel.org/r/20250131155842.3839098-1-beata.michalska@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
PRMD register is only meaningful on the beginning stage of exception
entry, and it is overwritten with nested irq or exception.
When CPU runs in VM mode, interrupt need be enabled on host. And the
mode for host had better be kernel mode rather than random or user mode.
When VM is running, the running mode with top command comes from CRMD
register, and running mode should be kernel mode since kernel function
is executing with perf command. It needs be consistent with both top and
perf command.
Now kernel_page_present() always return true for KPRANGE/XKPRANGE
addresses, this isn't correct because hibernation (ACPI S4) use it
to distinguish whether a page is saveable. If all KPRANGE/XKPRANGE
addresses are considered as saveable, then reserved memory such as
EFI_RUNTIME_SERVICES_CODE / EFI_RUNTIME_SERVICES_DATA will also be
saved and restored.
Fix this by returning true only if the KPRANGE/XKPRANGE address is in
memblock.memory.
In some environments, the SCLP firmware interface used to query a
CHPID's configured state is not supported. On these environments,
rapidly reading the corresponding sysfs attribute produces inconsistent
results:
This occurs for example when Linux is run as a KVM guest. The
inconsistency is a result of CIO using cached results for generating
the value of the "configure" attribute while failing to handle the
situation where no data was returned by SCLP.
Fix this by not updating the cache-expiration timestamp when SCLP
returns no data. With the fix applied, the system response is
consistent:
$ cat /sys/devices/css0/chp0.00/configure
cat: /sys/devices/css0/chp0.00/configure: Operation not supported
$ cat /sys/devices/css0/chp0.00/configure
cat: /sys/devices/css0/chp0.00/configure: Operation not supported
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com> Reviewed-by: Eric Farman <farman@linux.ibm.com> Tested-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DT bindings for ov7251 specify "enable" GPIO (xshutdown in
documentation) but the int3472 indiscriminately provides this as a "reset"
GPIO to sensor drivers. Take this into account by assigning it as "enable"
with active high polarity for INT347E devices, i.e. ov7251. "reset" with
active low polarity remains the default GPIO name for other devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250211072841.7713-3-sakari.ailus@linux.intel.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Struct gpiod_lookup flags field's type is unsigned long. Thus use unsigned
long for values to be assigned to that field. Similarly, also call the
field gpio_flags which it really is.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250211072841.7713-2-sakari.ailus@linux.intel.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On ThinkPad X120e, fan speed is reported in ticks per revolution
rather than RPM.
Recalculate the fan speed value reported for ThinkPad X120e
to RPM based on a 22.5 kHz clock.
Based on the information on
https://www.thinkwiki.org/wiki/How_to_control_fan_speed,
the same problem is highly likely to be relevant to at least Edge11,
but Edge11 is not addressed in this patch.
Signed-off-by: Sybil Isabel Dorsett <sybdorsett@proton.me> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20250203163255.5525-1-sybdorsett@proton.me Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clarify that wake_up_q() does an atomic write to task->wake_q.next, after
which a concurrent __wake_q_add() can immediately overwrite
task->wake_q.next again.
It is meaningless to shift a byte count by folio_shift(). The folio index
is in units of PAGE_SIZE, not folio_size(). We can use folio_contains()
to make this work for arbitrary-order folios, so remove the assertion
that the folios are of order 0.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Omoton KB066 is an Apple A1255 keyboard clone (HID product code
05ac:022c). On both keyboards, the F6 key becomes Num Lock when the Fn
key is held. But unlike its Apple exemplar, when the Omoton's F6 key is
pressed without Fn, it sends the usage code 0xC0301 from the reserved
section of the consumer page instead of the standard F6 usage code
0x7003F from the keyboard page. The nonstandard code is translated to
KEY_UNKNOWN and becomes useless on Linux. The Omoton KB066 is a pretty
popular keyboard, judging from its 29,058 reviews on Amazon at time of
writing, so let's account for its quirk to make it more usable.
By the way, it would be nice if we could automatically set fnmode to 0
for Omoton keyboards because they handle the Fn key internally and the
kernel's Fn key handling creates undesirable side effects such as making
F1 and F2 always Brightness Up and Brightness Down in fnmode=1 (the
default) or always F1 and F2 in fnmode=2. Unfortunately I don't think
there's a way to identify Bluetooth keyboards more specifically than the
HID product code which is obviously inaccurate. Users of Omoton
keyboards will just have to set fnmode to 0 manually to get full Fn key
functionality.
Add Apple Magic Keyboard 2024 model (with USB-C port) device ID (0320)
to those recognized by the hid-apple driver. Keyboard is otherwise
compatible with the existing implementation for its earlier 2021 model.
Newer model R3* Topre Realforce keyboards share an issue with their older
R2 cousins where a report descriptor fixup is needed in order for n-key
rollover to work correctly, otherwise only 6-key rollover is available.
This patch adds some new hardware IDs for the R3S 87-key keyboard and
makes amendments to the existing hid-topre driver in order to change the
correct byte in the new model.
Since commit c141ecc3cecd7 ("of: Warn when of_property_read_bool() is
used on non-boolean properties") a warning is raised if this function
is used for property detection. of_property_present() is the correct
helper for this.
When lizard mode is disabled, there were two issues:
1. Switching between gamepad mode and desktop mode still functioned, even
though desktop mode did not. This lead to the ability to "break" gamepad mode
by holding down the Options key even while lizard mode is disabled
2. If you were in desktop mode when lizard mode is disabled, you would
immediately enter this faulty mode.
This patch properly disables the ability to switch between gamepad mode and the
faulty desktop mode by holding the Options key, as well as effectively removing
the faulty mode by bypassing the early returns if lizard mode is disabled.
The HP 5MP Camera (USB ID 0408:5473) reports a HID sensor interface that
is not actually implemented. Attempting to access this non-functional
sensor via iio_info causes system hangs as runtime PM tries to wake up
an unresponsive sensor.
The ISH driver performs a clock sync with the firmware once at system
startup and then every 20 seconds. If a firmware reset occurs right
after a clock sync, the driver would wait 20 seconds before performing
another clock sync with the firmware. This is particularly problematic
with the introduction of the "load firmware from host" feature, where
the driver performs a clock sync with the bootloader and then has to
wait 20 seconds before syncing with the main firmware.
This patch clears prev_sync immediately upon receiving an IPC reset,
so that the main firmware and driver will perform a clock sync
immediately after completing the IPC handshake.
The timestamps in the Firmware log and HID sensor samples are incorrect.
They show 1970-01-01 because the current IPC driver only uses the first
8 bytes of bootup time when synchronizing time with the firmware. The
firmware converts the bootup time to UTC time, which results in the
display of 1970-01-01.
In write_ipc_from_queue(), when sending the MNG_SYNC_FW_CLOCK message,
the clock is updated according to the definition of ipc_time_update_msg.
However, in _ish_sync_fw_clock(), the message length is specified as the
size of uint64_t when building the doorbell. As a result, the firmware
only receives the first 8 bytes of struct ipc_time_update_msg.
This patch corrects the length in the doorbell to ensure the entire
ipc_time_update_msg is sent, fixing the timestamp issue.
dsp_local_on has several incorrect assumptions, one of which is that
p->nr_cpus_allowed always tracks p->cpus_ptr. This is not true when a task
is scheduled out while migration is disabled - p->cpus_ptr is temporarily
overridden to the previous CPU while p->nr_cpus_allowed remains unchanged.
This led to sporadic test faliures when dsp_local_on_dispatch() tries to put
a migration disabled task to a different CPU. Fix it by keeping the previous
CPU when migration is disabled.
There are SCX schedulers that make use of p->nr_cpus_allowed. They should
also implement explicit handling for p->migration_disabled.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Ihor Solodrai <ihor.solodrai@pm.me> Cc: Andrea Righi <arighi@nvidia.com> Cc: Changwoo Min <changwoo@igalia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
STATMOUNT_MNT_OPTS can actually be missing if there are no options. This
is a change of behavior since 75ead69a7173 ("fs: don't let statmount return
empty strings").
The other checks shouldn't actually trigger, but add them for correctness
and for easier debugging if the test fails.
Building with GCC 15 results in build error
fs/vboxsf/super.c:24:54: error: initializer-string for array of ‘unsigned char’ is too long [-Werror=unterminated-string-initialization]
24 | static const unsigned char VBSF_MOUNT_SIGNATURE[4] = "\000\377\376\375";
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Due to GCC having enabled -Werror=unterminated-string-initialization[0]
by default. Separately initializing each array element of
VBSF_MOUNT_SIGNATURE to ensure NUL termination, thus satisfying GCC 15
and fixing the build error.
Richard Henderson <richard.henderson@linaro.org> writes[1]:
> There was a Spec benchmark (I forget which) which was memory bound and ran
> twice as fast with 32-bit pointers.
>
> I copied the idea from DEC to the ELF abi, but never did all the other work
> to allow the toolchain to take advantage.
>
> Amusingly, a later Spec changed the benchmark data sets to not fit into a
> 32-bit address space, specifically because of this.
>
> I expect one could delete the ELF bit and personality and no one would
> notice. Not even the 10 remaining Alpha users.
In [2] it was pointed out that parts of setarch weren't working
properly on alpha because it has it's own SET_PERSONALITY
implementation. In the discussion that followed Richard Henderson
pointed out that the 32bit pointer support for alpha was never
completed.
Fix this by removing alpha's 32bit pointer support.
As a bit of paranoia refuse to execute any alpha binaries that have
the EF_ALPHA_32BIT flag set. Just in case someone somewhere has
binaries that try to use alpha's 32bit pointer support.
projects / thirdparty / kernel / stable.git / log
