Marvell PPv2 Header Parser sets some bits in the 'result_info' field in
each lookup iteration, to identify different packet attributes such as
DSA / VLAN tag, protocol infos, etc. This is used in further
classification stages in the controller.
It's the DSA tag detection entry that is in charge of detecting when there
is a single VLAN tag.
This commits adds the missing update of the result_info in this case.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve fscrypt read performance by switching the decryption workqueue
from bound to unbound. With the bound workqueue, when multiple bios
completed on the same CPU, they were decrypted on that same CPU. But
with the unbound queue, they are now decrypted in parallel on any CPU.
Although fscrypt read performance can be tough to measure due to the
many sources of variation, this change is most beneficial when
decryption is slow, e.g. on CPUs without AES instructions. For example,
I timed tarring up encrypted directories on f2fs. On x86 with AES-NI
instructions disabled, the unbound workqueue improved performance by
about 25-35%, using 1 to NUM_CPUs jobs with 4 or 8 CPUs available. But
with AES-NI enabled, performance was unchanged to within ~2%.
I also did the same test on a quad-core ARM CPU using xts-speck128-neon
encryption. There performance was usually about 10% better with the
unbound workqueue, bringing it closer to the unencrypted speed.
The unbound workqueue may be worse in some cases due to worse locality,
but I think it's still the better default. dm-crypt uses an unbound
workqueue by default too, so this change makes fscrypt match.
This patch fixes it by adding module version info.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.
This patch fixes it by adjusting the location of some function.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM CCN PMU driver uses dev_warn() to complain about parameters in
the user-provided perf_event_attr. This means that under normal
operation (e.g. a single invocation of the perf tool), a number of
messages warnings may be logged to dmesg.
Tools may issue multiple syscalls to probe for feature support, and
multiple applications (from multiple users) can attempt to open events
simultaneously, so this is not very helpful, even if a user happens to
have access to dmesg. Worse, this can push important information out of
the dmesg ring buffer, and can significantly slow down syscall fuzzers,
vastly increasing the time it takes to find critical bugs.
Demote the dev_warn() instances to dev_dbg(), as is the case for all
other PMU drivers under drivers/perf/. Users who wish to debug PMU event
initialisation can enable dynamic debug to receive these messages.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. Taking into account coverage
class in slot time configuration allows to increase by an order of
magnitude the throughput on a 4Km link in a noisy environment
Tested-by: Luca Bisti <luca.bisti@gmail.com> Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we request control of native PCIe hotplug unconditionally.
Native PCIe hotplug events are handled by the pciehp driver, and if it is
not enabled those events will be lost.
Request control of native PCIe hotplug only if the pciehp driver is
enabled, so we will actually handle native PCIe hotplug events.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For multi-function programs, loading the address of a callee
function to a register requires emitting instructions whose
count varies from one to five depending on the nature of the
address.
Since we come to know of the callee's address only before the
extra pass, the number of instructions required to load this
address may vary from what was previously generated. This can
make the JITed image grow or shrink.
To avoid this, we should generate a constant five-instruction
when loading function addresses by padding the optimized load
sequence with NOPs.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, for multi-function programs, we cannot get the JITed
instructions using the bpf system call's BPF_OBJ_GET_INFO_BY_FD
command. Because of this, userspace tools such as bpftool fail
to identify a multi-function program as being JITed or not.
With the JIT enabled and the test program running, this can be
verified as follows:
# cat /proc/sys/net/core/bpf_jit_enable
1
Before applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T11:43:38+0530 uid 0
xlated 216B not jited memlock 65536B
...
# bpftool prog dump jited id 1
no instructions returned
After applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T12:13:01+0530 uid 0
xlated 216B jited 308B memlock 65536B
...
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019] Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Fixes: 7ff0b53c4051145d ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a fix from reviewing the code, but it looks like it might be
able to lead to an Oops. It affects 32bit systems.
The KVM_MEMORY_ENCRYPT_REG_REGION ioctl uses a u64 for range->addr and
range->size but the high 32 bits would be truncated away on a 32 bit
system. This is harmless but it's also harmless to prevent it.
Then in sev_pin_memory() the "uaddr + ulen" calculation can wrap around.
The wrap around can happen on 32 bit or 64 bit systems, but I was only
able to figure out a problem for 32 bit systems. We would pick a number
which results in "npages" being zero. The sev_pin_memory() would then
return ZERO_SIZE_PTR without allocating anything.
I made it illegal to call sev_pin_memory() with "ulen" set to zero.
Hopefully, that doesn't cause any problems. I also changed the type of
"first" and "last" to long, just for cosmetic reasons. Otherwise on a
64 bit system you're saving "uaddr >> 12" in an int and it truncates the
high 20 bits away. The math works in the current code so far as I can
see but it's just weird.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[Brijesh noted that the code is only reachable on X86_64.] Reviewed-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/time.c:41:13: error: no previous prototype for ‘chrp_time_init’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:66:5: error: no previous prototype for ‘chrp_cmos_clock_read’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:74:6: error: no previous prototype for ‘chrp_cmos_clock_write’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:86:5: error: no previous prototype for ‘chrp_set_rtc_time’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:130:6: error: no previous prototype for ‘chrp_get_rtc_time’ [-Werror=missing-prototypes]
we aggregate FAIR utilization only if this class has runnable tasks.
This was mainly due to avoid the risk to stay on an high frequency just
because of the blocked utilization of a CPU not being properly decayed
while the CPU was idle.
However, since:
commit 31e77c93e432 ("sched/fair: Update blocked load when newly idle")
the FAIR blocked utilization is properly decayed also for IDLE CPUs.
This allows us to use the FAIR blocked utilization as a safe mechanism
to gracefully reduce the frequency only if no FAIR tasks show up on a
CPU for a reasonable period of time.
Moreover, we also reduce the frequency drops of CPUs running periodic
tasks which, depending on the task periodicity and the time required
for a frequency switch, was increasing the chances to introduce some
undesirable performance variations.
Reported-by: Vincent Guittot <vincent.guittot@linaro.org> Tested-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Vincent Guittot <vincent.guittot@linaro.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Joel Fernandes <joelaf@google.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Morten Rasmussen <morten.rasmussen@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Steve Muckle <smuckle@google.com> Link: http://lkml.kernel.org/r/20180524141023.13765-2-patrick.bellasi@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nvme timeout handling doesn't do anything if the pci channel is
offline, which is the case when recovering from PCI error event, so it
was a bad idea to sync the controller reset in this state. This patch
flushes the reset work in the error_resume callback instead when the
channel is back to online. This keeps AER handling serialized and
can recover from timeouts.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199757 Fixes: cc1d5e749a2e ("nvme/pci: Sync controller reset for AER slot_reset") Reported-by: Alex Gagniuc <mr.nuke.me@gmail.com> Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For any failure after nvme_rdma_start_queue in
nvme_rdma_configure_admin_queue, the admin queue will be freed with the
NVME_RDMA_Q_LIVE flag still set. Once nvme_rdma_stop_queue is invoked,
that will cause a use-after-free.
BUG: KASAN: use-after-free in rdma_disconnect+0x1f/0xe0 [rdma_cm]
To fix it, call nvme_rdma_stop_queue for all the failed cases after
nvme_rdma_start_queue.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Suggested-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two places report an error when a partition header is found to
not contain the right canary value. The error messages do not
properly byte swap the host ids. Fix this, and adjust the format
specificier to match the 16-bit unsigned data type.
Move the error handling for a bad canary value to the end of
qcom_smem_alloc_private(). This avoids some long lines, and
reduces the distraction of handling this unexpected problem.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is at least one entry in the partition table, but no global
entry, the qcom_smem_set_global_partition() should return an error
just like it does if there are no partition table entries.
It turns out the function still returns an error in this case, but
it waits to do so until it has mistakenly treated the last entry in
the table as if it were the global entry found.
Fix the function to return immediately if no global entry is found
in the table.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qmi_handle_init(), a buffer is allocated for to hold messages
received through the handle's socket. Any "normal" messages
(expected by the caller) will have a header prepended, so the
buffer size is adjusted to accomodate that.
The buffer must also be of sufficient size to receive control
messages, so the size is increased if necessary to ensure these
will fit.
Unfortunately the calculation is done wrong, making it possible
for the calculated buffer size to be too small to hold a "normal"
message. Specifically, if:
the current logic will use sizeof(struct qrtr_ctrl_pkt) as the
receive buffer size, which is not enough to hold the maximum
"normal" message plus its header. Currently this problem occurs
for (13 < recv_buf_size < 20).
This patch corrects this.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under the following case, qgroup rescan can double account cowed tree
blocks:
In this case, extent tree only has one tree block.
-
| transid=5 last committed=4
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 4).
| Scan it, set qgroup_rescan_progress to the last
| EXTENT/META_ITEM + 1
| now qgroup_rescan_progress = A + 1.
|
| fs tree get CoWed, new tree block is at A + 16K
| transid 5 get committed
-
| transid=6 last committed=5
| btrfs_qgroup_rescan_worker()
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 5).
| scan it using qgroup_rescan_progress (A + 1).
| found new tree block beyong A, and it's fs tree block,
| account it to increase qgroup numbers.
-
In above case, tree block A, and tree block A + 16K get accounted twice,
while qgroup rescan should stop when it already reach the last leaf,
other than continue using its qgroup_rescan_progress.
Such case could happen by just looping btrfs/017 and with some
possibility it can hit such double qgroup accounting problem.
Fix it by checking the path to determine if we should finish qgroup
rescan, other than relying on next loop to exit.
Reported-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code assumes that there's an implied barrier by the
sequence of code preceding the wakeup, namely the mutex unlock.
As Nikolay pointed out:
I think this is wrong (not your code) but the original assumption that
the RELEASE semantics provided by mutex_unlock is sufficient.
According to memory-barriers.txt:
Section 'LOCK ACQUISITION FUNCTIONS' states:
(2) RELEASE operation implication:
Memory operations issued before the RELEASE will be completed before the
RELEASE operation has completed.
Memory operations issued after the RELEASE *may* be completed before the
RELEASE operation has completed.
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb050941b ("Btrfs: Cache free inode numbers in memory") Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer is queued or requeued in vb2_buffer_done, then don't
call the finish memop. In this case the buffer is only returned to vb2,
not to userspace.
Calling 'finish' here will cause an unbalance when the queue is
canceled, since the core will call the same memop again.
The current logic makes Smatch to false-detect a Spectre variant 1
vulnerability. The problem is that it initializes an u32 indirectly
from user space input.
After trying to write a fixup, after a while I realized that, in
practice, this shouldn't be a problem, as an u32 is initialized
from u8, but it took some time to discover it.
So, do some code cleanup to make it clearer for both humans
and machines about the valid range for "op".
Fix this warning:
drivers/media/cec/cec-pin-error-inj.c:170 cec_pin_error_inj_parse_line() warn: potential spectre issue 'pin->error_inj_args'
When the driver is configured in the "memcpy" dma-mode,
it uses vb2_vmalloc_memops, which is backed by a SLAB
allocator and so shouldn't be using GFP_DMA32.
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Acked-by: Benson Leung <bleung@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case, one BE is used by two FE1/FE2
FE1--->BE-->
|
FE2----]
when FE1/FE2 call dpcm_be_dai_hw_free() together
the BE users will be 2 (> 1), hence cannot be hw_free
the be state will leave at, ex. SND_SOC_DPCM_STATE_STOP
later FE1/FE2 call dpcm_be_dai_shutdown(),
will be skip due to wrong state.
leaving the BE not being hw_free and shutdown.
The BE dai will be hw_free later when calling
dpcm_be_dai_shutdown() if still in invalid state.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the arm-cci driver is enabled, but both CONFIG_ARM_CCI5xx_PMU and
CONFIG_ARM_CCI400_PMU are not, we get a warning about how parts of
the driver are never used:
drivers/perf/arm-cci.c:1454:29: error: 'cci_pmu_models' defined but not used [-Werror=unused-variable]
drivers/perf/arm-cci.c:693:16: error: 'cci_pmu_event_show' defined but not used [-Werror=unused-function]
drivers/perf/arm-cci.c:685:16: error: 'cci_pmu_format_show' defined but not used [-Werror=unused-function]
Marking all three functions as __maybe_unused avoids the warnings in
randconfig builds. I'm doing this lacking any ideas for a better fix.
Fixes: 3de6be7a3dd8 ("drivers/bus: Split Arm CCI driver") Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following warning during boot:
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
__might_sleep+0x7c/0x88
In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a0e ("iwlwifi: mvm: change open and close criteria of a BA session") Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
[Problem description and how we fix it]
We should balance dirty metadata pages at the end of
btrfs_finish_ordered_io, since a small, unmergeable random write can
potentially produce dirty metadata which is multiple times larger than
the data itself. For example, a small, unmergeable 4KiB write may
produce:
16KiB dirty leaf (and possibly 16KiB dirty node) in subvolume tree
16KiB dirty leaf (and possibly 16KiB dirty node) in checksum tree
16KiB dirty leaf (and possibly 16KiB dirty node) in extent tree
Although we do call balance dirty pages in write side, but in the
buffered write path, most metadata are dirtied only after we reach the
dirty background limit (which by far only counts dirty data pages) and
wakeup the flusher thread. If there are many small, unmergeable random
writes spread in a large btree, we'll find a burst of dirty pages
exceeds the dirty_bytes limit after we wakeup the flusher thread - which
is not what we expect. In our machine, it caused out-of-memory problem
since a page cannot be dropped if it is marked dirty.
Someone may worry about we may sleep in btrfs_btree_balance_dirty_nodelay,
but since we do btrfs_finish_ordered_io in a separate worker, it will not
stop the flusher consuming dirty pages. Also, we use different worker for
metadata writeback endio, sleep in btrfs_finish_ordered_io help us throttle
the size of dirty metadata pages.
[Reproduce steps]
To reproduce the problem, we need to do 4KiB write randomly spread in a
large btree. In our 2GiB RAM machine:
1) Create 4 subvolumes.
2) Run fio on each subvolume:
3) Take snapshot on each subvolume and repeat fio on existing files.
4) Repeat step (3) until we get large btrees.
In our case, by observing btrfs_root_item->bytes_used, we have 2GiB of
metadata in each subvolume tree and 12GiB of metadata in extent tree.
5) Stop all fio, take snapshot again, and wait until all delayed work is
completed.
6) Start all fio. Few seconds later we hit OOM when the flusher starts
to work.
Driver switches vif sta_state into QTNF_STA_CONNECTING when cfg80211
core initiates connect procedure. Further this state is changed either
to QTNF_STA_CONNECTED or to QTNF_STA_DISCONNECTED by BSS_JOIN and
BSS_LEAVE events from firmware. However it is possible that no such
events will be sent by firmware, e.g. if EAPOL timed out.
In this case vif sta_mode will remain in QTNF_STA_CONNECTING state and
all subsequent connection attempts will fail with -EBUSY error code.
Fix this by perfroming STA state transition from QTNF_STA_CONNECTING
to QTNF_STA_DISCONNECTED in cfg80211 disconnect callback.
No need to rely upon firmware events in this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were picking up the wrong header should use asm/ioctls.h form the kernel
and not the header from the system (sys/ioctl.h). In the current code we
added the correct include and we added the kernel headers path to the CFLAGS.
When devpts_pts test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative
result even when the test could not be run.
In another case, it returns pass for a skipped test reporting a false
postive.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Change it to use ksft_exit_skip() when test is skipped.
When intel_pstate test is skipped because of unmet dependencies and/or
unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even
when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When kvm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Change it to use ksft_exit_skip() when the test is skipped. In addition,
refine test_assert() message to include strerror() string and add explicit
check for EACCES to cleary identify when test doesn't run when access is
denied to resources required e.g: open /dev/kvm failed, rc: -1 errno: 13
When memfd test is skipped because of unmet dependencies and/or unsupported
configuration, it returns non-zero value which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit check for root user at the start of memfd hugetlbfs test
and return skip code if a non-root user attempts to run it.
In addition, return skip code when not enough huge pages are available to
run the test.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
A few changes improve the overall usability of the test:
* fix a hard-coded maximum frequency (3300),
* don't adjust the CPU frequency if only evaluating results,
* fix a comparison for multiple frequencies.
A symptom of that last issue looked like this:
./run.sh: line 107: [: too many arguments
./run.sh: line 110: 3099
3099
3100-3100: syntax error in expression (error token is \"3099
3100-3100\")
Because a check will count how many differente frequencies
there are among the CPUs of the system, and after they are
tallied another read is performed, which might produce
different results.
For Nehalem and Westmere, there is only one fixed counter for W-Box.
There is no index which is bigger than UNCORE_PMC_IDX_FIXED.
It is not correct to use >= to check fixed counter.
The code quality issue will bring problem when new counter index is
introduced.
Signed-off-by: Kan Liang <kan.liang@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: acme@kernel.org Cc: eranian@google.com Link: http://lkml.kernel.org/r/1525371913-10597-2-git-send-email-kan.liang@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no index which is bigger than UNCORE_PMC_IDX_FIXED. The only
exception is client IMC uncore, which has been specially handled.
For generic code, it is not correct to use >= to check fixed counter.
The code quality issue will bring problem when a new counter index is
introduced.
Signed-off-by: Kan Liang <kan.liang@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: acme@kernel.org Cc: eranian@google.com Link: http://lkml.kernel.org/r/1525371913-10597-3-git-send-email-kan.liang@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the amount of available ports varies by the kernels build
configuration. To remove the limitation of the fixed 128 ports
we allocate the amount of idevs by using the number we get
from the kernel.
detach_port() fails to call usbip_vhci_driver_close() from its error
path after usbip_vhci_detach_device() returns failure, leaking memory
allocated in usbip_vhci_driver_open() and holding udev_context and udev
references. Fix it to call usbip_vhci_driver_close().
In bfq_requests_merged(), there is a deadlock because the lock on
bfqq->bfqd->lock is held by the calling function, but the code of
this function tries to grab the lock again.
This deadlock is currently hidden by another bug (fixed by next commit
for this source file), which causes the body of bfq_requests_merged()
to be never executed.
This commit removes the deadlock by removing the lock/unlock pair.
After revoking atomic write, related LBA can be reused by others, so we
need to wait page writeback before reusing the LBA, in order to avoid
interference between old atomic written in-flight IO and new IO.
With data_flush mount option, during recovery, in order to avoid entering
above writeback flow, let's detect recovery status and do skip in
f2fs_balance_fs_bg.
Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Yunlei He <heyunlei@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch disables loading of f2fs module on architectures
which have PAGE_SIZE > 4096 , since it is impossible to mount f2fs on
such architectures , log messages are:
mount: /mnt: wrong fs type, bad option, bad superblock on
/dev/vdiskb1, missing codepage or helper program, or other error.
/dev/vdiskb1: F2FS filesystem,
UUID=1d8b9ca4-2389-4910-af3b-10998969f09c, volume name ""
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 1th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 2th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
If the server recalls the layout that was just handed out, we risk hitting
a race as described in RFC5661 Section 2.10.6.3 unless we ensure that we
release the sequence slot after processing the LAYOUTGET operation that
was sent as part of the OPEN compound.
When cleaning up buffer entries as we wrap up, their state should be
"completed". If any of the entries is in "submitted" state, it means
that something bad has happened. Trigger a warning immediately instead of
waiting for the state flag to eventually be updated, thus hiding the
issue.
Currently in case of error caused by bio_pc_add_page in
pblk_bio_add_pages two issues occur when calling from
pblk_rb_read_to_bio(). First one is in pblk_bio_free_pages, since we
are trying to free pages not allocated from our mempool. Second one
is the warn from dma_pool_free, that we are trying to free NULL
pointer dma.
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.
This patch fixes it by disabling the phy when resetting.
Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The si544 driver had a rounding problem that using the result of clk_round_rate
may set the clock to yet another rate, for example:
clk_round_rate(195000000) = 194999999
clk_round_rate(194999999) = 194999998
Clients would expect that after clk_set_rate(clk, freq2=clk_round_rate(clk, freq)) the
chip will be running at exactly freq2.
The problem was in the calculation of the feedback divider, it was always rounded
down instead of to the nearest possible VCO value.
After this change, the following holds true for any supported frequency:
actual_freq = clk_round_rate(clk, freq);
clk_set_rate(clk, actual_freq);
clk_round_rate(clk, actual_freq) == actual_freq && clk_get_rate(clk) == actual_freq
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Fixes: 953cc3e81170 ("clk: Add driver for the si544 clock generator chip") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.
GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.
from arch/powerpc/kernel/time.c:
unsigned long tb_ticks_per_usec = 100; /* sane default */
Currently, all powernv systems have a timebase frequency of 512mhz
(512000000/1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.
So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.
The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: Stewart Smith <stewart@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A no-op form of ori (or immediate of 0 into r31 and the result stored
in r31) has been re-tasked as a speculation barrier. The instruction
only acts as a barrier on newer machines with appropriate firmware
support. On older CPUs it remains a harmless no-op.
Implement barrier_nospec using this instruction.
mpe: The semantics of the instruction are believed to be that it
prevents execution of subsequent instructions until preceding branches
have been fully resolved and are no longer executing speculatively.
There is no further documentation available at this time.
Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
