This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org> Fixes: 9f8b17e643fe ("USB: make usbdevices export their device nodes instead of using a separate class") Signed-off-by: Ma Ke <make_ruc2021@163.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com> Cc: stable <stable@kernel.org> Fixes: d920a2ed8620 ("usb: Disable USB3 LPM at shutdown") Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the regression introduced by commit d8c6edfa3f4e ("USB:
usblp: don't call usb_set_interface if there's a single alt"),
which causes that unsupported protocols can also be set via
ioctl when the num_altsetting of the device is 1.
Move the check for protocol support to the earlier stage.
Fixes: d8c6edfa3f4e ("USB: usblp: don't call usb_set_interface if there's a single alt") Cc: stable <stable@kernel.org> Signed-off-by: Jun Yan <jerrysteve1101@gmail.com> Link: https://lore.kernel.org/r/20241212143852.671889-1-jerrysteve1101@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Runtime PM documentation (Section 5) mentions, during remove()
callbacks, drivers should undo the runtime PM changes done in
probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc. Hence add missing
function to disable autosuspend on dwc3-am62 driver unbind.
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Driver returns -EOPNOTSUPPORTED on unsupported parameters case in set
config. Upper level driver checks for -ENOTSUPP. Because of the return
code mismatch, the ioctls from userspace fail. Resolve the issue by
passing -ENOTSUPP during unsupported case.
Fixes: 7d3e4d807df2 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.") Cc: stable <stable@kernel.org> Signed-off-by: Rengarajan S <rengarajan.s@microchip.com> Link: https://lore.kernel.org/r/20241205133626.1483499-3-rengarajan.s@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resolve kernel panic caused by improper handling of IRQs while
accessing GPIO values. This is done by replacing generic_handle_irq with
handle_nested_irq.
Fixes: 1f4d8ae231f4 ("misc: microchip: pci1xxxx: Add gpio irq handler and irq helper functions irq_ack, irq_mask, irq_unmask and irq_set_type of irq_chip.") Cc: stable <stable@kernel.org> Signed-off-by: Rengarajan S <rengarajan.s@microchip.com> Link: https://lore.kernel.org/r/20241205133626.1483499-2-rengarajan.s@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During fuzz testing, the following warning was discovered:
different return values (15 and 11) from vsnprintf("%*pbl
", ...)
test:keyward is WARNING in kvasprintf
WARNING: CPU: 55 PID: 1168477 at lib/kasprintf.c:30 kvasprintf+0x121/0x130
Call Trace:
kvasprintf+0x121/0x130
kasprintf+0xa6/0xe0
bitmap_print_to_buf+0x89/0x100
core_siblings_list_read+0x7e/0xb0
kernfs_file_read_iter+0x15b/0x270
new_sync_read+0x153/0x260
vfs_read+0x215/0x290
ksys_read+0xb9/0x160
do_syscall_64+0x56/0x100
entry_SYSCALL_64_after_hwframe+0x78/0xe2
The call trace shows that kvasprintf() reported this warning during the
printing of core_siblings_list. kvasprintf() has several steps:
(1) First, calculate the length of the resulting formatted string.
(2) Allocate a buffer based on the returned length.
(3) Then, perform the actual string formatting.
(4) Check whether the lengths of the formatted strings returned in
steps (1) and (2) are consistent.
If the core_cpumask is modified between steps (1) and (3), the lengths
obtained in these two steps may not match. Indeed our test includes cpu
hotplugging, which should modify core_cpumask while printing.
To fix this issue, cache the cpumask into a temporary variable before
calling cpumap_print_{list, cpumask}_to_buf(), to keep it unchanged
during the printing process.
Fixes: bb9ec13d156e ("topology: use bin_attribute to break the size limitation of cpumap ABI") Cc: stable <stable@kernel.org> Signed-off-by: Li Huafei <lihuafei1@huawei.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20241114110141.94725-1-lihuafei1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
This fixes data corruption when accessing the internal SD card in mass
storage mode.
I am actually not too sure why. I didn't figure a straightforward way to
reproduce the issue, but i seem to get garbage when issuing a lot (over 50)
of large reads (over 120 sectors) are done in a quick succession. That is,
time seems to matter here -- larger reads are fine if they are done with
some delay between them.
But I'm not great at understanding this sort of things, so I'll assume
the issue other, smarter, folks were seeing with similar phones is the
same problem and I'll just put my quirk next to theirs.
The "Software details" screen on the phone is as follows:
V 04.06
07-08-13
RM-849
(c) Nokia
TL;DR version of the device descriptor:
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x06c2
bcdDevice 4.06
iManufacturer 1 Nokia
iProduct 2 Nokia 208
The patch assumes older firmwares are broken too (I'm unable to test, but
no biggie if they aren't I guess), and I have no idea if newer firmware
exists.
User Perspective:
When a user sets the phase value, the ad9832_write_phase() is called.
The phase register has a 12-bit resolution, so the valid range is 0 to
4095. If the phase offset value of 4096 is input, it effectively exactly
equals 0 in the lower 12 bits, meaning no offset.
Reasons for the Change:
1) Original Condition (phase > BIT(AD9832_PHASE_BITS)):
This condition allows a phase value equal to 2^12, which is 4096.
However, this value exceeds the valid 12-bit range, as the maximum valid
phase value should be 4095.
2) Modified Condition (phase >= BIT(AD9832_PHASE_BITS)):
Ensures that the phase value is within the valid range, preventing
invalid datafrom being written.
Impact on Subsequent Logic: st->data = cpu_to_be16(addr | phase):
If the phase value is 2^12, i.e., 4096 (0001 0000 0000 0000), and addr
is AD9832_REG_PHASE0 (1100 0000 0000 0000), then addr | phase results in
1101 0000 0000 0000, occupying DB12. According to the section of WRITING
TO A PHASE REGISTER in the datasheet, the MSB 12 PHASE0 bits should be
DB11. The original condition leads to incorrect DB12 usage, which
contradicts the datasheet and could pose potential issues for future
updates if DB12 is used in such related cases.
User Perspective:
When a user sets the phase value, the ad9834_write_phase() is called.
The phase register has a 12-bit resolution, so the valid range is 0 to
4095. If the phase offset value of 4096 is input, it effectively exactly
equals 0 in the lower 12 bits, meaning no offset.
Reasons for the Change:
1) Original Condition (phase > BIT(AD9834_PHASE_BITS)):
This condition allows a phase value equal to 2^12, which is 4096.
However, this value exceeds the valid 12-bit range, as the maximum valid
phase value should be 4095.
2) Modified Condition (phase >= BIT(AD9834_PHASE_BITS)):
Ensures that the phase value is within the valid range, preventing
invalid datafrom being written.
Impact on Subsequent Logic: st->data = cpu_to_be16(addr | phase):
If the phase value is 2^12, i.e., 4096 (0001 0000 0000 0000), and addr
is AD9834_REG_PHASE0 (1100 0000 0000 0000), then addr | phase results in
1101 0000 0000 0000, occupying DB12. According to the section of WRITING
TO A PHASE REGISTER in the datasheet, the MSB 12 PHASE0 bits should be
DB11. The original condition leads to incorrect DB12 usage, which
contradicts the datasheet and could pose potential issues for future
updates if DB12 is used in such related cases.
Lonial reported an issue in the BPF verifier where check_mem_size_reg()
has the following code:
if (!tnum_is_const(reg->var_off))
/* For unprivileged variable accesses, disable raw
* mode so that the program is required to
* initialize all the memory that the helper could
* just partially fill up.
*/
meta = NULL;
This means that writes are not checked when the register containing the
size of the passed buffer has not a fixed size. Through this bug, a BPF
program can write to a map which is marked as read-only, for example,
.rodata global maps.
The problem is that MEM_UNINIT's initial meaning that "the passed buffer
to the BPF helper does not need to be initialized" which was added back
in commit 435faee1aae9 ("bpf, verifier: add ARG_PTR_TO_RAW_STACK type")
got overloaded over time with "the passed buffer is being written to".
The problem however is that checks such as the above which were added later
via 06c1c049721a ("bpf: allow helpers access to variable memory") set meta
to NULL in order force the user to always initialize the passed buffer to
the helper. Due to the current double meaning of MEM_UNINIT, this bypasses
verifier write checks to the memory (not boundary checks though) and only
assumes the latter memory is read instead.
Fix this by reverting MEM_UNINIT back to its original meaning, and having
MEM_WRITE as an annotation to BPF helpers in order to then trigger the
BPF verifier checks for writing to memory.
Some notes: check_arg_pair_ok() ensures that for ARG_CONST_SIZE{,_OR_ZERO}
we can access fn->arg_type[arg - 1] since it must contain a preceding
ARG_PTR_TO_MEM. For check_mem_reg() the meta argument can be removed
altogether since we do check both BPF_READ and BPF_WRITE. Same for the
equivalent check_kfunc_mem_size_reg().
Fixes: 7b3552d3f9f6 ("bpf: Reject writes for PTR_TO_MAP_KEY in check_helper_mem_access") Fixes: 97e6d7dab1ca ("bpf: Check PTR_TO_MEM | MEM_RDONLY in check_helper_mem_access") Fixes: 15baa55ff5b0 ("bpf/verifier: allow all functions to read user provided context") Reported-by: Lonial Con <kongln9170@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20241021152809.33343-2-daniel@iogearbox.net Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: BRUNO VERNAY <bruno.vernay@se.com> Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a MEM_WRITE attribute for BPF helper functions which can be used in
bpf_func_proto to annotate an argument type in order to let the verifier
know that the helper writes into the memory passed as an argument. In
the past MEM_UNINIT has been (ab)used for this function, but the latter
merely tells the verifier that the passed memory can be uninitialized.
There have been bugs with overloading the latter but aside from that
there are also cases where the passed memory is read + written which
currently cannot be expressed, see also 4b3786a6c539 ("bpf: Zero former
ARG_PTR_TO_{LONG,INT} args in case of error").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20241021152809.33343-1-daniel@iogearbox.net Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: BRUNO VERNAY <bruno.vernay@se.com> Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com>
Stable-dep-of: 8ea607330a39 ("bpf: Fix overloading of MEM_UNINIT's meaning") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that was fixed in the commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size")
but later broken again in the commit 8ca7cab82bda ("dm verity fec: fix misaligned RS roots IO")
If the Reed-Solomon roots setting spans multiple blocks, the code does not
use proper parity bytes and randomly fails to repair even trivial errors.
This bug cannot happen if the sector size is multiple of RS roots
setting (Android case with roots 2).
The previous solution was to find a dm-bufio block size that is multiple
of the device sector size and roots size. Unfortunately, the optimization
in commit 8ca7cab82bda ("dm verity fec: fix misaligned RS roots IO")
is incorrect and uses data block size for some roots (for example, it uses
4096 block size for roots = 20).
This patch uses a different approach:
- It always uses a configured data block size for dm-bufio to avoid
possible misaligned IOs.
- and it caches the processed parity bytes, so it can join it
if it spans two blocks.
As the RS calculation is called only if an error is detected and
the process is computationally intensive, copying a few more bytes
should not introduce performance issues.
The issue was reported to cryptsetup with trivial reproducer
https://gitlab.com/cryptsetup/cryptsetup/-/issues/923
# create an erasure that should always be repairable with this roots setting
dd if=/dev/zero of=data.img conv=notrunc bs=1 count=4 seek=4 status=none
# try to read it through dm-verity
veritysetup open data.img test hash.img --fec-device=fec.img --fec-roots=20 $(cat roothash)
dd if=/dev/mapper/test of=/dev/null bs=4096 status=noxfer
Even now the log says it cannot repair it:
: verity-fec: 7:1: FEC 0: failed to correct: -74
: device-mapper: verity: 7:1: data block 0 is corrupted
...
With this fix, errors are properly repaired.
: verity-fec: 7:1: FEC 0: corrected 4 errors
Like the Vivobook X1704VAP the X1504VAP has its keyboard IRQ (1) described
as ActiveLow in the DSDT, which the kernel overrides to EdgeHigh which
breaks the keyboard.
Add the X1504VAP to the irq1_level_low_skip_override[] quirk table to fix
this.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219224 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patch.msgid.link/20241220181352.25974-1-hdegoede@redhat.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TongFang GM5HG0A is a TongFang barebone design which is sold under
various brand names.
The ACPI IRQ override for the keyboard IRQ must be used on these AMD Zen
laptops in order for the IRQ to work.
At least on the SKIKK Vanaheim variant the DMI product- and board-name
strings have been replaced by the OEM with "Vanaheim" so checking that
board-name contains "GM5HG0A" as is usually done for TongFang barebones
quirks does not work.
The DMI OEM strings do contain "GM5HG0A". I have looked at the dmidecode
for a few other TongFang devices and the TongFang code-name string being
in the OEM strings seems to be something which is consistently true.
Add a quirk checking one of the DMI_OEM_STRING(s) is "GM5HG0A" in the hope
that this will work for other OEM versions of the "GM5HG0A" too.
die() can be called in exception handler, and therefore cannot sleep.
However, die() takes spinlock_t which can sleep with PREEMPT_RT enabled.
That causes the following warning:
Switch to use raw_spinlock_t, which does not sleep even with PREEMPT_RT
enabled.
Fixes: 76d2a0493a17 ("RISC-V: Init and Halt Code") Signed-off-by: Nam Cao <namcao@linutronix.de> Cc: stable@vger.kernel.org Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20241118091333.1185288-1-namcao@linutronix.de Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Wrapper functions for dcn_bw_ceil2() and dcn_bw_floor2()
should check for granularity is non zero to avoid assert and
divide-by-zero error in dcn_bw_ functions.
[How]
Add check for granularity 0.
Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6e09701c3eb2ccb8cb0518e0b67f1c69742a4ec) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.probe_interval' is
used.
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.rto_min/max' is used.
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.sctp_hmac_alg' is
used.
dm-ebs uses dm-bufio to process requests that are not aligned on logical
sector size. dm-bufio doesn't support passing integrity data (and it is
unclear how should it do it), so we shouldn't set the
DM_TARGET_PASSES_INTEGRITY flag.
The documentation in rculist.h explains the absence of list_empty_rcu()
and cautions programmers against relying on a list_empty() ->
list_first() sequence in RCU safe code. This is because each of these
functions performs its own READ_ONCE() of the list head. This can lead
to a situation where the list_empty() sees a valid list entry, but the
subsequent list_first() sees a different view of list head state after a
modification.
In the case of dm-thin, this author had a production box crash from a GP
fault in the process_deferred_bios path. This function saw a valid list
head in get_first_thin() but when it subsequently dereferenced that and
turned it into a thin_c, it got the inside of the struct pool, since the
list was now empty and referring to itself. The kernel on which this
occurred printed both a warning about a refcount_t being saturated, and
a UBSAN error for an out-of-bounds cpuid access in the queued spinlock,
prior to the fault itself. When the resulting kdump was examined, it
was possible to see another thread patiently waiting in thin_dtr's
synchronize_rcu.
The thin_dtr call managed to pull the thin_c out of the active thins
list (and have it be the last entry in the active_thins list) at just
the wrong moment which lead to this crash.
Fortunately, the fix here is straight forward. Switch get_first_thin()
function to use list_first_or_null_rcu() which performs just a single
READ_ONCE() and returns NULL if the list is already empty.
This was run against the devicemapper test suite's thin-provisioning
suites for delete and suspend and no regressions were observed.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Fixes: b10ebd34ccca ("dm thin: fix rcu_read_lock being held in code that can sleep") Cc: stable@vger.kernel.org Acked-by: Ming-Hung Tsai <mtsai@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'np' device_node is initialized via of_cpu_device_node_get(), which
requires explicit calls to of_node_put() when it is no longer required
to avoid leaking the resource.
Instead of adding the missing calls to of_node_put() in all execution
paths, use the cleanup attribute for 'np' by means of the __free()
macro, which automatically calls of_node_put() when the variable goes
out of scope. Given that 'np' is only used within the
for_each_possible_cpu(), reduce its scope to release the nood after
every iteration of the loop.
Fixes: 6abf32f1d9c5 ("cpuidle: Add RISC-V SBI CPU idle driver") Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://lore.kernel.org/r/20241116-cpuidle-riscv-sbi-cleanup-v3-1-a3a46372ce08@gmail.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When `ksmbd_vfs_kern_path_locked` met an error and it is not the last
entry, it will exit without restoring changed path buffer. But later this
buffer may be used as the filename for creation.
Fixes: c5a709f08d40 ("ksmbd: handle caseless file creation") Signed-off-by: He Wang <xw897002528@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kafs filesystem limits the maximum length of a cell to 256 bytes, but a
problem occurs if someone actually does that: kafs tries to create a
directory under /proc/net/afs/ with the name of the cell, but that fails
with a warning:
WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:405
because procfs limits the maximum filename length to 255.
However, the DNS limits the maximum lookup length and, by extension, the
maximum cell name, to 255 less two (length count and trailing NUL).
Fix this by limiting the maximum acceptable cellname length to 253. This
also allows us to be sure we can create the "/afs/.<cell>/" mountpoint too.
Further, split the YFS VL record cell name maximum to be the 256 allowed by
the protocol and ignore the record retrieved by YFSVL.GetCellName if it
exceeds 253.
Fixes: c3e9f888263b ("afs: Implement client support for the YFSVL.GetCellName RPC op") Reported-by: syzbot+7848fee1f1e5c53f912b@syzkaller.appspotmail.com Closes: https://lore.kernel.org/r/6776d25d.050a0220.3a8527.0048.GAE@google.com/ Signed-off-by: David Howells <dhowells@redhat.com> Link: https://lore.kernel.org/r/376236.1736180460@warthog.procyon.org.uk Tested-by: syzbot+7848fee1f1e5c53f912b@syzkaller.appspotmail.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the smb2_send_interim_resp(), if ksmbd_alloc_work_struct()
fails to allocate a node, it returns a NULL pointer to the
in_work pointer. This can lead to an illegal memory write of
in_work->response_buf when allocate_interim_rsp_buf() attempts
to perform a kzalloc() on it.
To address this issue, incorporating a check for the return
value of ksmbd_alloc_work_struct() ensures that the function
returns immediately upon allocation failure, thereby preventing
the aforementioned illegal memory access.
Fixes: 041bba4414cd ("ksmbd: fix wrong interim response on compound") Signed-off-by: Wentao Liang <liangwentao@iscas.ac.cn> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check the return value of drm_dp_dpcd_readb() to confirm that
AUX communication is successful. To simplify the code, replace
drm_dp_dpcd_readb() and DP_GET_SINK_COUNT() with drm_dp_read_sink_count().
Fix dp mode valid issue to avoid abnormal display of limit state.
After DP passes link training, it can express the lane count of the
current link status is good. Calculate the maximum bandwidth supported
by DP using the current lane count.
The color format will select the best one based on the bandwidth
requirements of the current timing mode. If the current timing mode
uses RGB and meets the DP link bandwidth requirements, RGB will be used.
If the timing mode uses RGB but does not meet the DP link bandwidthi
requirements, it will continue to check whether YUV422 meets
the DP link bandwidth.
FEC overhead is approximately 2.4% from DP 1.4a spec 2.2.1.4.2.
The down-spread amplitude shall either be disabled (0.0%) or up
to 0.5% from 1.4a 3.5.2.6. Add up to approximately 3% total overhead.
Because rate is already divided by 10,
mode->clock does not need to be multiplied by 10.
The PHY portion of the mediatek hdmi driver was originally part of
the driver it self and later split out into drivers/phy, which a
'select' to keep the prior behavior.
However, this leads to build failures when the PHY driver cannot
be built:
WARNING: unmet direct dependencies detected for PHY_MTK_HDMI
Depends on [n]: (ARCH_MEDIATEK || COMPILE_TEST [=y]) && COMMON_CLK [=y] && OF [=y] && REGULATOR [=n]
Selected by [m]:
- DRM_MEDIATEK_HDMI [=m] && HAS_IOMEM [=y] && DRM [=m] && DRM_MEDIATEK [=m]
ERROR: modpost: "devm_regulator_register" [drivers/phy/mediatek/phy-mtk-hdmi-drv.ko] undefined!
ERROR: modpost: "rdev_get_drvdata" [drivers/phy/mediatek/phy-mtk-hdmi-drv.ko] undefined!
The best option here is to just not select the phy driver and leave that
up to the defconfig. Do the same for the other PHY and memory drivers
selected here as well for consistency.
Fixes: a481bf2f0ca4 ("drm/mediatek: Separate mtk_hdmi_phy to an independent module") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20241218085837.2670434-1-arnd@kernel.org/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When cmd_alloc_index(), fails cmd_work_handler() needs
to complete ent->slotted before returning early.
Otherwise the task which issued the command may hang:
mlx5_core 0000:01:00.0: cmd_work_handler:877:(pid 3880418): failed to allocate command entry
INFO: task kworker/13:2:4055883 blocked for more than 120 seconds.
Not tainted 4.19.90-25.44.v2101.ky10.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/13:2 D 0 4055883 2 0x00000228
Workqueue: events mlx5e_tx_dim_work [mlx5_core]
Call trace:
__switch_to+0xe8/0x150
__schedule+0x2a8/0x9b8
schedule+0x2c/0x88
schedule_timeout+0x204/0x478
wait_for_common+0x154/0x250
wait_for_completion+0x28/0x38
cmd_exec+0x7a0/0xa00 [mlx5_core]
mlx5_cmd_exec+0x54/0x80 [mlx5_core]
mlx5_core_modify_cq+0x6c/0x80 [mlx5_core]
mlx5_core_modify_cq_moderation+0xa0/0xb8 [mlx5_core]
mlx5e_tx_dim_work+0x54/0x68 [mlx5_core]
process_one_work+0x1b0/0x448
worker_thread+0x54/0x468
kthread+0x134/0x138
ret_from_fork+0x10/0x18
Fixes: 485d65e13571 ("net/mlx5: Add a timeout to acquire the command queue semaphore") Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Acked-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20250108030009.68520-1-zhaochenguang@kylinos.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even though we fixed a logic error in the commit cited below, syzbot
still managed to trigger an underflow of the per-host bulk flow
counters, leading to an out of bounds memory access.
To avoid any such logic errors causing out of bounds memory accesses,
this commit factors out all accesses to the per-host bulk flow counters
to a series of helpers that perform bounds-checking before any
increments and decrements. This also has the benefit of improving
readability by moving the conditional checks for the flow mode into
these helpers, instead of having them spread out throughout the
code (which was the cause of the original logic error).
As part of this change, the flow quantum calculation is consolidated
into a helper function, which means that the dithering applied to the
ost load scaling is now applied both in the DRR rotation and when a
sparse flow's quantum is first initiated. The only user-visible effect
of this is that the maximum packet size that can be sent while a flow
stays sparse will now vary with +/- one byte in some cases. This should
not make a noticeable difference in practice, and thus it's not worth
complicating the code to preserve the old behaviour.
Use INT_MAX as maximum size for the conntrack hashtable. Otherwise, it
is possible to hit WARN_ON_ONCE in __kvmalloc_node_noprof() when
resizing hashtable because __GFP_NOWARN is unset. See:
0708a0afe291 ("mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls")
Note: hashtable resize is only possible from init_netns.
Fixes: 9cc1c73ad666 ("netfilter: conntrack: avoid integer overflow when resizing") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a follow-up to 3c5b4d69c358 ("net: annotate data-races around
sk->sk_mark"). sk->sk_mark can be read and written without holding
the socket lock. IPv6 equivalent is already covered with READ_ONCE()
annotation in tcp_v6_send_response().
This fixes errors such as the following when Own address type is set to
Random Address but it has not been programmed yet due to either be
advertising or connecting:
< HCI Command: LE Set Exte.. (0x08|0x0041) plen 13
Own address type: Random (0x03)
Filter policy: Ignore not in accept list (0x01)
PHYs: 0x05
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Entry 1: LE Coded
Type: Passive (0x00)
Interval: 180.000 msec (0x0120)
Window: 90.000 msec (0x0090)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Exten.. (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Enable (0x08|0x0042) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Fixes: c45074d68a9b ("Bluetooth: Fix not generating RPA when required") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We've noticed that NFS can hang when using RPC over TLS on an unstable
connection, and investigation shows that the RPC layer is stuck in a tight
loop attempting to transmit, but forever getting -EBADMSG back from the
underlying network. The loop begins when tcp_sendmsg_locked() returns
-EPIPE to tls_tx_records(), but that error is converted to -EBADMSG when
calling the socket's error reporting handler.
Instead of converting errors from tcp_sendmsg_locked(), let's pass them
along in this path. The RPC layer handles -EPIPE by reconnecting the
transport, which prevents the endless attempts to transmit on a broken
connection.
ptp4l application reports too high offset when ran on E823 device
with a 100GB/s link. Those values cannot go under 100ns, like in a
working case when using 100 GB/s cable.
This is due to incorrect frequency settings on the PHY clocks for
100 GB/s speed. Changes are introduced to align with the internal
hardware documentation, and correctly initialize frequency in PHY
clocks with the frequency values that are in our HW spec.
To reproduce the issue run ptp4l as a Time Receiver on E823 device,
and observe the offset, which will never approach values seen
in the PTP working case.
During ARP failure, tid is not inserted but _c4iw_free_ep()
attempts to remove tid which results in error.
This patch fixes the issue by avoiding removal of uninserted tid.
Fixes: 59437d78f088 ("cxgb4/chtls: fix ULD connection failures due to wrong TID base") Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com> Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Link: https://patch.msgid.link/20250103092327.1011925-1-anumula@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When hwrm_req_replace() fails, the driver is not invoking bnxt_req_drop()
which could cause a memory leak.
Fixes: bbf33d1d9805 ("bnxt_en: update all firmware calls to use the new APIs") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250104043849.3482067-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the backlog of listen() is set to zero, sk_acceptq_is_full() allows
one connection to be made, but inet_csk_reqsk_queue_is_full() does not.
When the net.ipv4.tcp_syncookies is zero, inet_csk_reqsk_queue_is_full()
will cause an immediate drop before the sk_acceptq_is_full() check in
tcp_conn_request(), resulting in no connection can be made.
This patch tries to keep consistent with 64a146513f8f ("[NET]: Revert
incorrect accept queue backlog changes.").
Since commit 099ecf59f05b ("net: annotate lockless accesses to
sk->sk_max_ack_backlog") decided to handle the sk_max_ack_backlog
locklessly, there is one more function mostly called in TCP/DCCP
cases. So this patch completes it:)
Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240331090521.71965-1-kerneljasonxing@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3479c7549fb1 ("tcp/dccp: allow a connection when sk_max_ack_backlog is zero") Signed-off-by: Sasha Levin <sashal@kernel.org>
802.2+LLC+SNAP frames received by napi_complete_done() with GRO and DSA
have skb->transport_header set two bytes short, or pointing 2 bytes
before network_header & skb->data. This was an issue as snap_rcv()
expected offset to point to SNAP header (OID:PID), causing packet to
be dropped.
A fix at llc_fixup_skb() (a024e377efed) resets transport_header for any
LLC consumers that may care about it, and stops SNAP packets from being
dropped, but doesn't fix the problem which is that LLC and SNAP should
not use transport_header offset.
Ths patch eliminates the use of transport_header offset for SNAP lookup
of OID:PID so that SNAP does not rely on the offset at all.
The offset is reset after pull for any SNAP packet consumers that may
(but shouldn't) use it.
Fixes: fda55eca5a33 ("net: introduce skb_transport_header_was_set()") Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250103012303.746521-1-antonio.pastor@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ca8210_test_interface_init() returns the result of kfifo_alloc(),
which can be non-zero in case of an error. The caller, ca8210_probe(),
should check the return value and do error-handling if it fails.
On Chromebooks based on Mediatek MT8195 or MT8188, the audio frontend
(AFE) is limited to accessing a very small window (1 MiB) of memory,
which is described as a reserved memory region in the device tree.
On these two platforms, the maximum buffer size is given as 512 KiB.
The MediaTek common code uses the same value for preallocations. This
means that only the first two PCM substreams get preallocations, and
then the whole space is exhausted, barring any other substreams from
working. Since the substreams used are not always the first two, this
means audio won't work correctly.
This is observed on the MT8188 Geralt Chromebooks, on which the
"mediatek,dai-link" property was dropped when it was upstreamed. That
property causes the driver to only register the PCM substreams listed
in the property, and in the order given.
Instead of trying to compute an optimal value and figuring out which
streams are used, simply disable preallocation. The PCM buffers are
managed by the core and are allocated and released on the fly. There
should be no impact to any of the other MediaTek platforms.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://patch.msgid.link/20241219105303.548437-1-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kuan-Wei Chiu [Mon, 6 Jan 2025 17:44:59 +0000 (01:44 +0800)]
scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
The orc_sort_cmp() function, used with qsort(), previously violated the
symmetry and transitivity rules required by the C standard. Specifically,
when both entries are ORC_REG_UNDEFINED, it could result in both a < b
and b < a, which breaks the required symmetry and transitivity. This can
lead to undefined behavior and incorrect sorting results, potentially
causing memory corruption in glibc implementations [1].
Symmetry: If x < y, then y > x.
Transitivity: If x < y and y < z, then x < z.
Fix the comparison logic to return 0 when both entries are
ORC_REG_UNDEFINED, ensuring compliance with qsort() requirements.
In __exfat_free_cluster(), the cluster chain is traversed until the
EOF cluster. If the cluster chain includes a loop due to file system
corruption, the EOF cluster cannot be traversed, resulting in an
infinite loop.
This commit uses the total number of clusters to prevent this infinite
loop.
If the file system is corrupted so that a cluster is linked to
itself in the cluster chain, and there is an unused directory
entry in the cluster, 'dentry' will not be incremented, causing
condition 'dentry < max_dentries' unable to prevent an infinite
loop.
This infinite loop causes s_lock not to be released, and other
tasks will hang, such as exfat_sync_fs().
This commit stops traversing the cluster chain when there is unused
directory entry in the cluster to avoid this infinite loop.
dm_array_cursor_skip() seeks to the target position by loading array
blocks iteratively until the specified number of entries to skip is
reached. When seeking across block boundaries, it uses
dm_array_cursor_next() to step into the next block.
dm_array_cursor_skip() must first move the cursor index to the end
of the current block; otherwise, the cursor position could incorrectly
remain in the same block, causing the actual number of skipped entries
to be much smaller than expected.
This bug affects cache resizing in v2 metadata and could lead to data
loss if the fast device is shrunk during the first-time resume. For
example:
1. create a cache metadata consists of 32768 blocks, with a dirty block
assigned to the second bitmap block. cache_restore v1.0 is required.
2. bring up the cache while attempt to discard all the blocks belonging
to the second bitmap block (block# 32576 to 32767). The last command
is expected to fail, but it actually succeeds.
In addition to the reproducer described above, this fix can be
verified using the "array_cursor/skip" tests in dm-unit:
dm-unit run /pdata/array_cursor/skip/ --kernel-dir <KERNEL_DIR>
Signed-off-by: Ming-Hung Tsai <mtsai@redhat.com> Fixes: 9b696229aa7d ("dm persistent data: add cursor skip functions to the cursor APIs") Reviewed-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cached block pointer in dm_array_cursor might be NULL if it reaches
an unreadable array block, or the array is empty. Therefore,
dm_array_cursor_end() should call dm_btree_cursor_end() unconditionally,
to prevent leaving unreleased btree blocks.
This fix can be verified using the "array_cursor/iterate/empty" test
in dm-unit:
dm-unit run /pdata/array_cursor/iterate/empty --kernel-dir <KERNEL_DIR>
When dm_bm_read_lock() fails due to locking or checksum errors, it
releases the faulty block implicitly while leaving an invalid output
pointer behind. The caller of dm_bm_read_lock() should not operate on
this invalid dm_block pointer, or it will lead to undefined result.
For example, the dm_array_cursor incorrectly caches the invalid pointer
on reading a faulty array block, causing a double release in
dm_array_cursor_end(), then hitting the BUG_ON in dm-bufio cache_put().
(snip)
device-mapper: array: array_block_check failed: blocknr 0 != wanted 10
device-mapper: block manager: array validator check failed for block 10
device-mapper: array: get_ablock failed
device-mapper: cache metadata: dm_array_cursor_next for mapping failed
------------[ cut here ]------------
kernel BUG at drivers/md/dm-bufio.c:638!
Fix by setting the cached block pointer to NULL on errors.
In addition to the reproducer described above, this fix can be
verified using the "array_cursor/damaged" test in dm-unit:
dm-unit run /pdata/array_cursor/damaged --kernel-dir <KERNEL_DIR>
When committing transaction in jbd2_journal_commit_transaction(), the
disk caches for the filesystem device should be flushed before updating
the journal tail sequence. However, this step is missed if the journal
is not located on the filesystem device. As a result, the filesystem may
become inconsistent following a power failure or system crash. Fix it by
ensuring that the filesystem device is flushed appropriately.
Fixes: 3339578f0578 ("jbd2: cleanup journal tail after transaction commit") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Link: https://lore.kernel.org/r/20241203014407.805916-3-yi.zhang@huaweicloud.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit '6a3afb6ac6df ("jbd2: increase the journal IO's priority")'
increases the priority of journal I/O by marking I/O with the
JBD2_JOURNAL_REQ_FLAGS. However, that commit missed the revoke buffers,
so also addresses that kind of I/Os.
Fixes: 6a3afb6ac6df ("jbd2: increase the journal IO's priority") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Link: https://lore.kernel.org/r/20241203014407.805916-2-yi.zhang@huaweicloud.com Reviewed-by: Kemeng Shi <shikemeng@huaweicloud.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_KASAN_SW_TAGS and CONFIG_KASAN_STACK are enabled, the
object_is_on_stack() function may produce incorrect results due to the
presence of tags in the obj pointer, while the stack pointer does not have
tags. This discrepancy can lead to incorrect stack object detection and
subsequently trigger warnings if CONFIG_DEBUG_OBJECTS is also enabled.
Element replace (with a socket different from the one stored) may race
with socket's close() link popping & unlinking. __sock_map_delete()
unconditionally unrefs the (wrong) element:
// set map[0] = s0
map_update_elem(map, 0, s0)
// drop fd of s0
close(s0)
sock_map_close()
lock_sock(sk) (s0!)
sock_map_remove_links(sk)
link = sk_psock_link_pop()
sock_map_unlink(sk, link)
sock_map_delete_from_link
// replace map[0] with s1
map_update_elem(map, 0, s1)
sock_map_update_elem
(s1!) lock_sock(sk)
sock_map_update_common
psock = sk_psock(sk)
spin_lock(&stab->lock)
osk = stab->sks[idx]
sock_map_add_link(..., &stab->sks[idx])
sock_map_unref(osk, &stab->sks[idx])
psock = sk_psock(osk)
sk_psock_put(sk, psock)
if (refcount_dec_and_test(&psock))
sk_psock_drop(sk, psock)
spin_unlock(&stab->lock)
unlock_sock(sk)
__sock_map_delete
spin_lock(&stab->lock)
sk = *psk // s1 replaced s0; sk == s1
if (!sk_test || sk_test == sk) // sk_test (s0) != sk (s1); no branch
sk = xchg(psk, NULL)
if (sk)
sock_map_unref(sk, psk) // unref s1; sks[idx] will dangle
psock = sk_psock(sk)
sk_psock_put(sk, psock)
if (refcount_dec_and_test())
sk_psock_drop(sk, psock)
spin_unlock(&stab->lock)
release_sock(sk)
Then close(map) enqueues bpf_map_free_deferred, which finally calls
sock_map_free(). This results in some refcount_t warnings along with
a KASAN splat [1].
Fix __sock_map_delete(), do not allow sock_map_unref() on elements that
may have been replaced.
[1]:
BUG: KASAN: slab-use-after-free in sock_map_free+0x10e/0x330
Write of size 4 at addr ffff88811f5b9100 by task kworker/u64:12/1063
The buggy address belongs to the object at ffff88811f5b9080
which belongs to the cache UNIX-STREAM of size 1984
The buggy address is located 128 bytes inside of
freed 1984-byte region [ffff88811f5b9080, ffff88811f5b9840)
Memory state around the buggy address: ffff88811f5b9000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88811f5b9080: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88811f5b9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88811f5b9200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Disabling lock debugging due to kernel taint
If the full path to be built by ceph_mdsc_build_path() happens to be
longer than PATH_MAX, then this function will enter an endless (retry)
loop, effectively blocking the whole task. Most of the machine
becomes unusable, making this a very simple and effective DoS
vulnerability.
I cannot imagine why this retry was ever implemented, but it seems
rather useless and harmful to me. Let's remove it and fail with
ENAMETOOLONG instead.
Cc: stable@vger.kernel.org Reported-by: Dario Weißer <dario@cure53.de> Signed-off-by: Max Kellermann <max.kellermann@ionos.com> Reviewed-by: Alex Markuze <amarkuze@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
[idryomov@gmail.com: backport to 6.1: pr_warn() is still in use] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zram: check comp is non-NULL before calling comp_destroy
This is a pre-requisite for the backport of commit 74363ec674cb ("zram:
fix uninitialized ZRAM not releasing backing device"), which has been
implemented differently in commit 7ac07a26dea7 ("zram: preparation for
multi-zcomp support") upstream.
We only need to ensure that zcomp_destroy is not called with a NULL
comp, so add this check as the other commit cannot be backported easily.
Under some corner cases the MPTCP protocol can end-up invoking
mptcp_cleanup_rbuf() when no data has been copied, but such helper
assumes the opposite condition.
Explicitly drop such assumption and performs the costly call only
when strictly needed - before releasing the msk socket lock.
Fixes: fd8976790a6c ("mptcp: be careful on MPTCP-level ack.") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-2-8608af434ceb@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the recvmsg() blocks after receiving some data - i.e. due to
SO_RCVLOWAT - the MPTCP code will attempt multiple times to
adjust the receive buffer size, wrongly accounting every time the
cumulative of received data - instead of accounting only for the
delta.
Address the issue moving mptcp_rcv_space_adjust just after the
data reception and passing it only the just received bytes.
This also removes an unneeded difference between the TCP and MPTCP
RX code path implementation.
Fixes: 581302298524 ("mptcp: error out earlier on disconnect") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-1-8608af434ceb@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric noted a probable shinfo->nr_frags corruption, which indeed
occurs.
The root cause is a buggy MPTCP option len computation in some
circumstances: the ADD_ADDR option should be mutually exclusive
with DSS since the blamed commit.
Still, mptcp_established_options_add_addr() tries to set the
relevant info in mptcp_out_options, if the remaining space is
large enough even when DSS is present.
Since the ADD_ADDR infos and the DSS share the same union
fields, adding first corrupts the latter. In the worst-case
scenario, such corruption increases the DSS binary layout,
exceeding the computed length and possibly overwriting the
skb shared info.
Address the issue by enforcing mutual exclusion in
mptcp_established_options_add_addr(), too.
Cc: stable@vger.kernel.org Reported-by: syzbot+38a095a81f30d82884c1@syzkaller.appspotmail.com Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/538 Fixes: 1bff1e43a30e ("mptcp: optimize out option generation") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/025d9df8cde3c9a557befc47e9bc08fbbe3476e5.1734771049.git.pabeni@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In allow_direct_reclaim(), while processing ZONE_DMA32, the sum of
inactive/active file-backed pages calculated in zone_reclaimable_pages()
based on the result of zone_page_state_snapshot() is zero.
Additionally, since this system lacks swap, the calculation of inactive/
active anonymous pages is skipped.
As a result, ZONE_DMA32 is deemed unreclaimable and skipped, moving on to
the processing of the next zone, ZONE_NORMAL, despite ZONE_DMA32 having
free pages significantly exceeding the high watermark.
The problem is that the pgdat->kswapd_failures hasn't been incremented.
This is because the node deemed balanced. The node balancing logic in
balance_pgdat() evaluates all zones collectively. If one or more zones
(e.g., ZONE_DMA32) have enough free pages to meet their watermarks, the
entire node is deemed balanced. This causes balance_pgdat() to exit early
before incrementing the kswapd_failures, as it considers the overall
memory state acceptable, even though some zones (like ZONE_NORMAL) remain
under significant pressure.
The patch ensures that zone_reclaimable_pages() includes free pages
(NR_FREE_PAGES) in its calculation when no other reclaimable pages are
available (e.g., file-backed or anonymous pages). This change prevents
zones like ZONE_DMA32, which have sufficient free pages, from being
mistakenly deemed unreclaimable. By doing so, the patch ensures proper
node balancing, avoids masking pressure on other zones like ZONE_NORMAL,
and prevents infinite loops in throttle_direct_reclaim() caused by
allow_direct_reclaim(pgdat) repeatedly returning false.
The kernel hangs due to a task stuck in throttle_direct_reclaim(), caused
by a node being incorrectly deemed balanced despite pressure in certain
zones, such as ZONE_NORMAL. This issue arises from
zone_reclaimable_pages() returning 0 for zones without reclaimable file-
backed or anonymous pages, causing zones like ZONE_DMA32 with sufficient
free pages to be skipped.
The lack of swap or reclaimable pages results in ZONE_DMA32 being ignored
during reclaim, masking pressure in other zones. Consequently,
pgdat->kswapd_failures remains 0 in balance_pgdat(), preventing fallback
mechanisms in allow_direct_reclaim() from being triggered, leading to an
infinite loop in throttle_direct_reclaim().
This patch modifies zone_reclaimable_pages() to account for free pages
(NR_FREE_PAGES) when no other reclaimable pages exist. This ensures zones
with sufficient free pages are not skipped, enabling proper balancing and
reclaim behavior.
When testing large folio support with XFS on our servers, we observed that
only a few large folios are mapped when reading large files via mmap.
After a thorough analysis, I identified it was caused by the
`/sys/block/*/queue/read_ahead_kb` setting. On our test servers, this
parameter is set to 128KB. After I tune it to 2MB, the large folio can
work as expected. However, I believe the large folio behavior should not
be dependent on the value of read_ahead_kb. It would be more robust if
the kernel can automatically adopt to it.
With /sys/block/*/queue/read_ahead_kb set to 128KB and performing a
sequential read on a 1GB file using MADV_HUGEPAGE, the differences in
/proc/meminfo are as follows:
- before this patch
FileHugePages: 18432 kB
FilePmdMapped: 4096 kB
- after this patch
FileHugePages: 1067008 kB
FilePmdMapped: 1048576 kB
This shows that after applying the patch, the entire 1GB file is mapped to
huge pages. The stable list is CCed, as without this patch, large folios
don't function optimally in the readahead path.
It's worth noting that if read_ahead_kb is set to a larger value that
isn't aligned with huge page sizes (e.g., 4MB + 128KB), it may still fail
to map to hugepages.
Link: https://lkml.kernel.org/r/20241108141710.9721-1-laoar.shao@gmail.com Link: https://lkml.kernel.org/r/20241206083025.3478-1-laoar.shao@gmail.com Fixes: 4687fdbb805a ("mm/filemap: Support VM_HUGEPAGE for file mappings") Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Tested-by: kernel test robot <oliver.sang@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While by default max_autoclose equals to INT_MAX / HZ, one may set
net.sctp.max_autoclose to UINT_MAX. There is code in
sctp_association_init() that can consequently trigger overflow.
Cc: stable@vger.kernel.org Fixes: 9f70f46bd4c7 ("sctp: properly latch and use autoclose value from sock to association") Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru> Acked-by: Xin Long <lucien.xin@gmail.com> Link: https://patch.msgid.link/20241219162114.2863827-1-kniv@yandex-team.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device uses MCP23xxx IO expander to receive IRQs, the following
bug can happen:
BUG: sleeping function called from invalid context
at kernel/locking/mutex.c:283
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ...
preempt_count: 1, expected: 0
...
Call Trace:
...
__might_resched+0x104/0x10e
__might_sleep+0x3e/0x62
mutex_lock+0x20/0x4c
regmap_lock_mutex+0x10/0x18
regmap_update_bits_base+0x2c/0x66
mcp23s08_irq_set_type+0x1ae/0x1d6
__irq_set_trigger+0x56/0x172
__setup_irq+0x1e6/0x646
request_threaded_irq+0xb6/0x160
...
We observed the problem while experimenting with a touchscreen driver which
used MCP23017 IO expander (I2C).
The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from
concurrent accesses, which is the default for regmaps without .fast_io,
.disable_locking, etc.
mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter
locks the mutex.
However, __setup_irq() locks desc->lock spinlock before calling these
functions. As a result, the system tries to lock the mutex whole holding
the spinlock.
It seems, the internal regmap locks are not needed in this driver at all.
mcp->lock seems to protect the regmap from concurrent accesses already,
except, probably, in mcp_pinconf_get/set.
mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under
chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes
mcp->lock and enables regmap caching, so that the potentially slow I2C
accesses are deferred until chip_bus_unlock().
The accesses to the regmap from mcp23s08_probe_one() do not need additional
locking.
In all remaining places where the regmap is accessed, except
mcp_pinconf_get/set(), the driver already takes mcp->lock.
This patch adds locking in mcp_pinconf_get/set() and disables internal
locking in the regmap config. Among other things, it fixes the sleeping
in atomic context described above.
In the expression "cmd.wqe_size * cmd.wr_count", both variables are u32
values that come from the user so the multiplication can lead to integer
wrapping. Then we pass the result to uverbs_request_next_ptr() which also
could potentially wrap. The "cmd.sge_count * sizeof(struct ib_uverbs_sge)"
multiplication can also overflow on 32bit systems although it's fine on
64bit systems.
This patch does two things. First, I've re-arranged the condition in
uverbs_request_next_ptr() so that the use controlled variable "len" is on
one side of the comparison by itself without any math. Then I've modified
all the callers to use size_mul() for the multiplications.
Fixes: 67cdb40ca444 ("[IB] uverbs: Implement more commands") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://patch.msgid.link/b8765ab3-c2da-4611-aae0-ddd6ba173d23@stanley.mountain Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gcc decides not to inline in_softirq_really(), objtool warns about a
function call with UACCESS enabled:
kernel/kcov.o: warning: objtool: __sanitizer_cov_trace_pc+0x1e: call to in_softirq_really() with UACCESS enabled
kernel/kcov.o: warning: objtool: check_kcov_mode+0x11: call to in_softirq_really() with UACCESS enabled
Mark this as __always_inline to avoid the problem.
Link: https://lkml.kernel.org/r/20241217071814.2261620-1-arnd@kernel.org Fixes: 7d4df2dad312 ("kcov: properly check for softirq context") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Marco Elver <elver@google.com> Cc: Aleksandr Nogikh <nogikh@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OSS sequencer handles the SysEx messages split in 6 bytes packets, and
ALSA sequencer OSS layer tries to combine those. It stores the data
in the internal buffer and this access is racy as of now, which may
lead to the out-of-bounds access.
As a temporary band-aid fix, introduce a mutex for serializing the
process of the SysEx message packets.
Reported-by: Kun Hu <huk23@m.fudan.edu.cn> Closes: https://lore.kernel.org/2B7E93E4-B13A-4AE4-8E87-306A8EE9BBB7@m.fudan.edu.cn Cc: <stable@vger.kernel.org> Link: https://patch.msgid.link/20241230110543.32454-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit eb91c456f371
("ALSA: hda/realtek: Add Framework Laptop 13 (Intel Core Ultra) to quirks")
and previous quirks for Framework systems with
Realtek codecs.
000C is a new platform that will also have an ALC285 codec and needs the
same quirk.
When building a 64-bit kernel, BITS_PER_LONG is defined as 64. However,
on a 32-bit build machine, the constant 1L is a signed 32-bit value.
Left-shifting it beyond 32 bits causes wraparound, and shifting by 31
or 63 bits makes it a negative value.
The fix in commit e0e92632715f ("[PATCH] PATCH: 1 line 2.6.18 bugfix:
modpost-64bit-fix.patch") is incorrect; it only addresses cases where
a 64-bit kernel is built on a 64-bit build machine, overlooking cases
on a 32-bit build machine.
Using 1ULL ensures a 64-bit width on both 32-bit and 64-bit machines,
avoiding the wraparound issue.
Fixes: e0e92632715f ("[PATCH] PATCH: 1 line 2.6.18 bugfix: modpost-64bit-fix.patch") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Stable-dep-of: bf36b4bf1b9a ("modpost: fix the missed iteration for the max bit in do_input()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190c0 ("xhci: retry Stop Endpoint on buggy NEC controllers") CC: stable@vger.kernel.org Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ARC GCC compiler is packaged starting from Fedora 39i and the GCC
variant of cross compile tools has arc-linux-gnu- prefix and not
arc-linux-. This is causing that CROSS_COMPILE variable is left unset.
This change allows builds without need to supply CROSS_COMPILE argument
if distro package is used.
Before this change:
$ make -j 128 ARCH=arc W=1 drivers/infiniband/hw/mlx4/
gcc: warning: ‘-mcpu=’ is deprecated; use ‘-mtune=’ or ‘-march=’ instead
gcc: error: unrecognized command-line option ‘-mmedium-calls’
gcc: error: unrecognized command-line option ‘-mlock’
gcc: error: unrecognized command-line option ‘-munaligned-access’
Some file systems do not ensure that the single call of iterate_dir
reaches the end of the directory. For example, FUSE fetches entries from
a daemon using 4KB buffer and stops fetching if entries exceed the
buffer. And then an actor of caller, KSMBD, is used to fill the entries
from the buffer.
Thus, pattern searching on FUSE, files located after the 4KB could not
be found and STATUS_NO_SUCH_FILE was returned.
Signed-off-by: Hobin Woo <hobin.woo@samsung.com> Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Reviewed-by: Namjae Jeon <linkinjeon@kernel.org> Tested-by: Yoonho Shin <yoonho.shin@samsung.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bpf_remove_insns() function returns WARN_ON_ONCE(error), where
error is a result of bpf_adj_branches(), and thus should be always 0
However, if for any reason it is not 0, then it will be converted to
boolean by WARN_ON_ONCE and returned to user space as 1, not an actual
error value. Fix this by returning the original err after the WARN check.
UAC 2 & 3 DAC's set bit 31 of the format to signal support for a
RAW_DATA type, typically used for DSD playback.
This is correctly tested by (format & UAC*_FORMAT_TYPE_I_RAW_DATA),
fp->dsd_raw = true; and call snd_usb_interface_dsd_format_quirks(),
however a confusing and unnecessary message gets printed because
the bit is not properly tested in the last "unsupported" if test:
if (format & ~0x3F) { ... }
For example the output:
usb 7-1: new high-speed USB device number 5 using xhci_hcd
usb 7-1: New USB device found, idVendor=262a, idProduct=9302, bcdDevice=0.01
usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
usb 7-1: Product: TC44C
usb 7-1: Manufacturer: TC44C
usb 7-1: SerialNumber: 5000000001
hid-generic 0003:262A:9302.001E: No inputs registered, leaving
hid-generic 0003:262A:9302.001E: hidraw6: USB HID v1.00 Device [DDHIFI TC44C] on usb-0000:08:00.3-1/input0
usb 7-1: 2:4 : unsupported format bits 0x100000000
This last "unsupported format" is actually wrong: we know the
format is a RAW_DATA which we assume is DSD, so there is no need
to print the confusing message.
This we unset bit 31 of the format after recognizing it, to avoid
the message.
Introduces the alc2xx-fixup-headset-mic model to simplify enabling
headset microphones on ALC2XX codecs.
Many recent configurations, as well as older systems that lacked this
fix for a long time, leave headset microphones inactive by default.
This addition provides a flexible workaround using the existing
ALC2XX_FIXUP_HEADSET_MIC quirk.
During the unmount path, at close_ctree(), we first stop the cleaner
kthread, using kthread_stop() which frees the associated task_struct, and
then stop and destroy all the work queues. However after we stopped the
cleaner we may still have a worker from the delalloc_workers queue running
inode.c:submit_compressed_extents(), which calls btrfs_add_delayed_iput(),
which in turn tries to wake up the cleaner kthread - which was already
destroyed before, resulting in a use-after-free on the task_struct.
Syzbot reported this with the following stack traces:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x78/0x2100 kernel/locking/lockdep.c:5089
Read of size 8 at addr ffff8880259d2818 by task kworker/u8:3/52
The buggy address belongs to the object at ffff8880259d1e00
which belongs to the cache task_struct of size 7424
The buggy address is located 2584 bytes inside of
freed 7424-byte region [ffff8880259d1e00, ffff8880259d3b00)
The SVM DMA device map direction should be set the same as
the DMA unmap setting, otherwise the DMA core will report
the following warning.
Before finialize this solution, there're some discussion on
the DMA mapping type(stream-based or coherent) in this KFD
migration case, followed by https://lore.kernel.org/all/04d4ab32
-45a1-4b88-86ee-fb0f35a0ca40@amd.com/T/.
As there's no dma_sync_single_for_*() in the DMA buffer accessed
that because this migration operation should be sync properly and
automatically. Give that there's might not be a performance problem
in various cache sync policy of DMA sync. Therefore, in order to
simplify the DMA direction setting alignment, let's set the DMA map
direction as BIDIRECTIONAL.
In case we fail to resume, we'll WARN with
"Hardware became unavailable during restart." and we'll wait until user
space does something. It'll typically bring the interface down and up to
recover. This won't work though because the queues are still stopped on
IEEE80211_QUEUE_STOP_REASON_SUSPEND reason.
Make sure we clear that reason so that we give a chance to the recovery
to succeed.
When a COWing a tree block, at btrfs_cow_block(), and we have the
tracepoint trace_btrfs_cow_block() enabled and preemption is also enabled
(CONFIG_PREEMPT=y), we can trigger a use-after-free in the COWed extent
buffer while inside the tracepoint code. This is because in some paths
that call btrfs_cow_block(), such as btrfs_search_slot(), we are holding
the last reference on the extent buffer @buf so btrfs_force_cow_block()
drops the last reference on the @buf extent buffer when it calls
free_extent_buffer_stale(buf), which schedules the release of the extent
buffer with RCU. This means that if we are on a kernel with preemption,
the current task may be preempted before calling trace_btrfs_cow_block()
and the extent buffer already released by the time trace_btrfs_cow_block()
is called, resulting in a use-after-free.
Fix this by moving the trace_btrfs_cow_block() from btrfs_cow_block() to
btrfs_force_cow_block() before the COWed extent buffer is freed.
This also has a side effect of invoking the tracepoint in the tree defrag
code, at defrag.c:btrfs_realloc_node(), since btrfs_force_cow_block() is
called there, but this is fine and it was actually missing there.
projects / thirdparty / kernel / stable.git / log
