Since the commit below the ipmr/ip6mr rtnl_unicast() code uses the portid
instead of the previous dst_pid which was copied from in_skb's portid.
Since the skb is new the portid is 0 at that point so the packets are sent
to the kernel and we get scheduling while atomic or a deadlock (depending
on where it happens) by trying to acquire rtnl two times.
Also since this is RTM_GETROUTE, it can be triggered by a normal user.
Fixes: 2942e9005056 ("[RTNETLINK]: Use rtnl_unicast() for rtnetlink unicasts") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Similar to commit 3be07244b733 ("ip6_gre: fix flowi6_proto value in
xmit path"), set flowi6_proto to IPPROTO_GRE for output route lookup.
Up until now, ip6gre_xmit_other() has set flowi6_proto to a bogus value.
This affected output route lookup for packets sent on an ip6gretap device
in cases where routing was dependent on the value of flowi6_proto.
Since the correct proto is already set in the tunnel flowi6 template via
commit 252f3f5a1189 ("ip6_gre: Set flowi6_proto as IPPROTO_GRE in xmit
path."), simply delete the line setting the incorrect flowi6_proto value.
Suggested-by: Jiri Benc <jbenc@redhat.com> Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
With TCP MTU probing enabled and offload TX checksumming disabled,
tcp_mtu_probe() calculated the wrong checksum when a fragment being copied
into the probe's SKB had an odd length. This was caused by the direct use
of skb_copy_and_csum_bits() to calculate the checksum, as it pads the
fragment being copied, if needed. When this fragment was not the last, a
subsequent call used the previous checksum without considering this
padding.
The effect was a stale connection in one way, as even retransmissions
wouldn't solve the problem, because the checksum was never recalculated for
the full SKB length.
Signed-off-by: Douglas Caetano dos Santos <douglascs@taghos.com.br> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
sk_mem_reclaim_partial() goal is to ensure each socket has
one SK_MEM_QUANTUM forward allocation. This is needed both for
performance and better handling of memory pressure situations in
follow up patches.
SK_MEM_QUANTUM is currently a page, but might be reduced to 4096 bytes
as some arches have 64KB pages.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When there is a CM id object that has port assigned to it, it means that
the cm-id asked for the specific port that it should go by it, but if
that port was removed (hot-unplug event) the cm-id was not updated.
In order to fix that the port keeps a list of all the cm-id's that are
planning to go by it, whenever the port is removed it marks all of them
as invalid.
This commit fixes a kernel panic which happens when running traffic between
guests and we force reboot a guest mid traffic, it triggers a kernel panic:
When an internal error condition is detected, make sure to set the
device inactive after dispatching the event so ULPs can get a
notification of this event.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When creating kernel CQs use 128B CQE stride if the
cache line size is 128B, 64B otherwise. This prevents
multiple CQEs from residing in a 128B cache line,
which can cause retries when there are concurrent
read and writes in one cache line.
Tested with IPoIB on PPC64, saw ~5% throughput
improvement.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure to drop the reference taken by class_find_device() after
opening the RTC device.
Fixes: 77437fd4e61f (pm: boot time suspend selftest) Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This subsystem consistently fails to drop the device reference taken by
class_find_device().
Note that some of these lookup functions already take a reference to the
returned data, while others claim no reference is needed (or does not
seem need one).
Fixes: 183b9b592a62 ("uwb: add the UWB stack (core files)") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba996302 ("mfd: add platform_device sharing support for mfd") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If the block size or cluster size is insane, reject the mount. This
is important for security reasons (although we shouldn't be just
depending on this check).
So Sebastian turned off the PIE for kernel builds but that was too late
- Kbuild.include already uses KBUILD_CFLAGS and trying to disable gcc
options with, say cc-disable-warning, fails:
gcc -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs
...
-Wno-sign-compare -fno-asynchronous-unwind-tables -Wframe-address -c -x c /dev/null -o .31392.tmp
/dev/null:1:0: error: code model kernel does not support PIC mode
because that returns an error and we can't disable the warning. For
example in this case:
which leads to gcc issuing all those warnings again.
So let's turn off PIE/PIC at the earliest possible moment, when we
declare KBUILD_CFLAGS so that cc-disable-warning picks it up too.
Also, we need the $(call cc-option ...) because -fno-PIE is supported
since gcc v3.4 and our lowest supported gcc version is 3.2 right now.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Adding -no-PIE to the fstack protector check. -no-PIE was introduced
before -fstack-protector so there is no need for a runtime check.
Without it the build stops:
|Cannot use CONFIG_CC_STACKPROTECTOR_STRONG: -fstack-protector-strong available but compiler is broken
due to -mcmodel=kernel + -fPIE if -fPIE is enabled by default.
Tagging it stable so it is possible to compile recent stable kernels as
well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Debian started to build the gcc with -fPIE by default so the kernel
build ends before it starts properly with:
|kernel/bounds.c:1:0: error: code model kernel does not support PIC mode
Also add to KBUILD_AFLAGS due to:
|gcc -Wp,-MD,arch/x86/entry/vdso/vdso32/.note.o.d … -mfentry -DCC_USING_FENTRY … vdso/vdso32/note.S
|arch/x86/entry/vdso/vdso32/note.S:1:0: sorry, unimplemented: -mfentry isn’t supported for 32-bit in combination with -fpic
Tagging it stable so it is possible to compile recent stable kernels as
well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
Function user_notifier_unregister should be called only once for each
registered user notifier.
Function kvm_arch_hardware_disable can be executed from an IPI context
which could cause a race condition with a VCPU returning to user mode
and attempting to unregister the notifier.
nf_log_proc_dostring() used current's network namespace instead of the one
corresponding to the sysctl file the write was performed on. Because the
permission check happens at open time and the nf_log files in namespaces
are accessible for the namespace owner, this can be abused by an
unprivileged user to effectively write to the init namespace's nf_log
sysctls.
Stash the "struct net *" in extra2 - data and extra1 are already used.
uid_t outer_uid;
gid_t outer_gid;
int stolen_fd = -1;
void writefile(char *path, char *buf) {
int fd = open(path, O_WRONLY);
if (fd == -1)
err(1, "unable to open thing");
if (write(fd, buf, strlen(buf)) != strlen(buf))
err(1, "unable to write thing");
close(fd);
}
int child_fn(void *p_) {
if (mount("proc", "/proc", "proc", MS_NOSUID|MS_NODEV|MS_NOEXEC,
NULL))
err(1, "mount");
/* Yes, we need to set the maps for the net sysctls to recognize us
* as namespace root.
*/
char buf[1000];
sprintf(buf, "0 %d 1\n", (int)outer_uid);
writefile("/proc/1/uid_map", buf);
writefile("/proc/1/setgroups", "deny");
sprintf(buf, "0 %d 1\n", (int)outer_gid);
writefile("/proc/1/gid_map", buf);
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.
In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.
gen_pool_alloc_algo() iterates over the chunks of a pool trying to find
a contiguous block of memory that satisfies the allocation request.
The shortcut
if (size > atomic_read(&chunk->avail))
continue;
makes the loop skip over chunks that do not have enough bytes left to
fulfill the request. There are two situations, though, where an
allocation might still fail:
(1) The available memory is not contiguous, i.e. the request cannot
be fulfilled due to external fragmentation.
(2) A race condition. Another thread runs the same code concurrently
and is quicker to grab the available memory.
In those situations, the loop calls pool->algo() to search the entire
chunk, and pool->algo() returns some value that is >= end_bit to
indicate that the search failed. This return value is then assigned to
start_bit. The variables start_bit and end_bit describe the range that
should be searched, and this range should be reset for every chunk that
is searched. Today, the code fails to reset start_bit to 0. As a
result, prefixes of subsequent chunks are ignored. Memory allocations
might fail even though there is plenty of room left in these prefixes of
those other chunks.
Fixes: 7f184275aa30 ("lib, Make gen_pool memory allocator lockless") Link: http://lkml.kernel.org/r/1477420604-28918-1-git-send-email-danielmentz@google.com Signed-off-by: Daniel Mentz <danielmentz@google.com> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
NFC version reply size checked against only header size, not against
full message size. That may lead potentially to uninitialized memory access
in version data.
That leads to warnings when version data is accessed:
drivers/misc/mei/bus-fixup.c: warning: '*((void *)&ver+11)' may be used uninitialized in this function [-Wuninitialized]: => 212:2
Reported in
Build regressions/improvements in v4.9-rc3
https://lkml.org/lkml/2016/10/30/57
[js] the check is in 3.12 only once
Fixes: 59fcd7c63abf (mei: nfc: Initial nfc implementation) Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Don't pass a size larger than iov_len to kernel_sendmsg().
Otherwise it will cause a NULL pointer deref when kernel_sendmsg()
returns with rv < size.
DRBD as external module has been around in the kernel 2.4 days already.
We used to be compatible to 2.4 and very early 2.6 kernels,
we used to use
rv = sock_sendmsg(sock, &msg, iov.iov_len);
then later changed to
rv = kernel_sendmsg(sock, &msg, &iov, 1, size);
when we should have used
rv = kernel_sendmsg(sock, &msg, &iov, 1, iov.iov_len);
tcp_sendmsg() used to totally ignore the size parameter. 57be5bd ip: convert tcp_sendmsg() to iov_iter primitives
changes that, and exposes our long standing error.
Even with this error exposed, to trigger the bug, we would need to have
an environment (config or otherwise) causing us to not use sendpage()
for larger transfers, a failing connection, and have it fail "just at the
right time". Apparently that was unlikely enough for most, so this went
unnoticed for years.
Still, it is known to trigger at least some of these,
and suspected for the others:
[0] http://lists.linbit.com/pipermail/drbd-user/2016-July/023112.html
[1] http://lists.linbit.com/pipermail/drbd-dev/2016-March/003362.html
[2] https://forums.grsecurity.net/viewtopic.php?f=3&t=4546
[3] https://ubuntuforums.org/showthread.php?t=2336150
[4] http://e2.howsolveproblem.com/i/1175162/
This should go into 4.9,
and into all stable branches since and including v4.0,
which is the first to contain the exposing change.
It is correct for all stable branches older than that as well
(which contain the DRBD driver; which is 2.6.33 and up).
It requires a small "conflict" resolution for v4.4 and earlier, with v4.5
we dropped the comment block immediately preceding the kernel_sendmsg().
Fixes: b411b3637fa7 ("The DRBD driver") Cc: viro@zeniv.linux.org.uk Cc: christoph.lechleitner@iteg.at Cc: wolfgang.glas@iteg.at Reported-by: Christoph Lechleitner <christoph.lechleitner@iteg.at> Tested-by: Christoph Lechleitner <christoph.lechleitner@iteg.at> Signed-off-by: Richard Weinberger <richard@nod.at>
[changed oneliner to be "obvious" without context; more verbose message] Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.
A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).
Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Acked-by: Marc Dietrich <marvin24@gmx.de> Fixes: 36b30d6138f4 ("staging: nvec: ps2: change serio type to passthrough") Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.
To prevent this from happening just let every party do its part of the
job.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Acked-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The ad5933_i2c_read function returns an error code to indicate
whether it could read data or not. However ad5933_work() ignores
this return code and just accesses the data unconditionally,
which gets detected by gcc as a possible bug:
drivers/staging/iio/impedance-analyzer/ad5933.c: In function 'ad5933_work':
drivers/staging/iio/impedance-analyzer/ad5933.c:649:16: warning: 'status' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds minimal error handling so we only evaluate the
data if it was correctly read.
Since commit d86bd1bece6f ("mm/slub: support left redzone") it is no longer
guaranteed that kmalloc(PAGE_SIZE) returns page aligned memory.
After the above commit we get an error for diag224 because aligned
memory is required. This leads to the following user visible error:
# mount none -t s390_hypfs /sys/hypervisor/
mount: unknown filesystem type 's390_hypfs'
# dmesg | grep hypfs
hypfs.cccfb8: The hardware system does not provide all functions
required by hypfs
hypfs.7a79f0: Initialization of hypfs failed with rc=-61
Fix this problem and use get_free_page() instead of kmalloc() to get
correctly aligned memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It could be not possible to freeze coredumping task when it waits for
'core_state->startup' completion, because threads are frozen in
get_signal() before they got a chance to complete 'core_state->startup'.
Inability to freeze a task during suspend will cause suspend to fail.
Also CRIU uses cgroup freezer during dump operation. So with an
unfreezable task the CRIU dump will fail because it waits for a
transition from 'FREEZING' to 'FROZEN' state which will never happen.
Use freezer_do_not_count() to tell freezer to ignore coredumping task
while it waits for core_state->startup completion.
Link: http://lkml.kernel.org/r/1475225434-3753-1-git-send-email-aryabinin@virtuozzo.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Tejun Heo <tj@kernel.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When root activates a swap partition whose header has the wrong
endianness, nr_badpages elements of badpages are swabbed before
nr_badpages has been checked, leading to a buffer overrun of up to 8GB.
This normally is not a security issue because it can only be exploited
by root (more specifically, a process with CAP_SYS_ADMIN or the ability
to modify a swap file/partition), and such a process can already e.g.
modify swapped-out memory of any other userspace process on the system.
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org> Tested-by: Sean Young <sean@mess.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com> Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch will fix regression caused by commit 1e793f6fc0db ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
Huge pages are not normally available to PV guests. Not suppressing
hugetlbfs use results in an endless loop of page faults when user mode
code tries to access a hugetlbfs mapped area (since the hypervisor
denies such PTEs to be created, but error indications can't be
propagated out of xen_set_pte_at(), just like for various of its
siblings), and - once killed in an oops like this:
s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change
e.g. the pageblock_order, which should be independent in respect to
hugepage support.
With this patch every architecture is free to define how to check
for hugepage support.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.
scan_pool() does not mark the PEB for scrubing when bitflips are
detected in the EC header of a free PEB (VID header region left to
0xff).
Make sure we scrub the PEB in this case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: dbb7d2a88d2a ("UBI: Add fastmap core") Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The smc91x driver defines a macro that compares its argument to
itself, apparently to get a true result while using its argument
to avoid a warning about unused local variables.
Unfortunately, this triggers a warning with gcc-6, as the comparison
is obviously useless:
drivers/net/ethernet/smsc/smc91x.c: In function 'smc_hardware_send_pkt':
drivers/net/ethernet/smsc/smc91x.c:563:14: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (!smc_special_trylock(&lp->lock, flags)) {
This replaces the macro with another one that behaves similarly,
with a cast to (void) to ensure the argument is used, and using
a literal 'true' as its value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
gcc-6.0 warns about comparisons between two identical expressions,
which is what we get in the floppy driver when writing to the FD_DOR
register:
drivers/block/floppy.c: In function 'set_dor':
drivers/block/floppy.c:810:44: error: self-comparison always evaluates to true [-Werror=tautological-compare]
fd_outb(newdor, FD_DOR);
It would be nice to use a static inline function instead of the
macro, to avoid the warning, but we cannot do that because the
FD_DOR definition is incomplete at this point.
Adding a cast to (u32) is a harmless way to shut up the warning,
just not very nice.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
xen_cleanhighmap() is operating on level2_kernel_pgt only. The upper
bound of the loop setting non-kernel-image entries to zero should not
exceed the size of level2_kernel_pgt.
The read is taking a considerable amount of time (about 50us on this
machine). The register does not ever hold anything other than the ring
ID that is updated in this exact function, so there is no need for
the read modify write cycle.
This chops off a big chunk of the time spent in hardirq disabled
context, as this function is called multiple times in the interrupt
handler. With this change applied radeon won't show up in the list
of the worst IRQ latency offenders anymore, where it was a regular
before.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The arcmsr driver failed to pass SYNCHRONIZE CACHE to controller
firmware. Depending on how drive caches are handled internally by
controller firmware this could potentially lead to data integrity
problems.
Ensure that cache flushes are passed to the controller.
[mkp: applied by hand and removed unused vars]
Signed-off-by: Ching Huang <ching2048@areca.com.tw> Reported-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59 Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In mac80211, multicast A-MSDUs are accepted in many cases that
they shouldn't be accepted in:
* drop A-MSDUs with a multicast A1 (RA), as required by the
spec in 9.11 (802.11-2012 version)
* drop A-MSDUs with a 4-addr header, since the fourth address
can't actually be useful for them; unless 4-address frame
format is actually requested, even though the fourth address
is still not useful in this case, but ignored
Accepting the first case, in particular, is very problematic
since it allows anyone else with possession of a GTK to send
unicast frames encapsulated in a multicast A-MSDU, even when
the AP has client isolation enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop.
Therefore it also needs a keyboard reset to detect the Elantech touchpad.
Otherwise the touchpad appears to be dead.
With this patch the touchpad is detected:
$ dmesg | grep -E "(i8042|Elantech|elantech)"
[ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.680372] i8042: Attempting to reset device connected to KBD port
[ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e)
[ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f.
[ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74
[ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
Commit c6017e793b93 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b93 ("virtio: console: add locks around buffer removal in port unplug path") Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The ERET instruction to return from exception is used for returning from
exception level (Status.EXL) and error level (Status.ERL). If both bits
are set however we should be returning from ERL first, as ERL can
interrupt EXL, for example when an NMI is taken. KVM however checks EXL
first.
Fix the order of the checks to match the pseudocode in the instruction
set manual.
vcpu->arch.wbinvd_dirty_mask may still be used after freeing it,
corrupting memory. For example, the following call trace may set a bit
in an already freed cpu mask:
kvm_arch_vcpu_load
vcpu_load
vmx_free_vcpu_nested
vmx_free_vcpu
kvm_arch_vcpu_free
Fix this by deferring freeing of wbinvd_dirty_mask.
The current tiocmget implementation would fail to report errors up the
stack and instead leaked a few bits from the stack as a mask of
modem-status flags.
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Size of kmalloc() in vc_do_resize() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Put a reasonable upper bound on terminal size to prevent WARNINGs.
The host keeps sending heartbeat packets independent of the
guest responding to them. Even though we respond to the heartbeat messages at
interrupt level, we can have situations where there maybe multiple heartbeat
messages pending that have not been responded to. For instance this occurs when the
VM is paused and the host continues to send the heartbeat messages.
Address this issue by draining and responding to all
the heartbeat messages that maybe pending.
Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Linus Torvalds [Tue, 8 Nov 2016 10:17:00 +0000 (11:17 +0100)]
Fix potential infoleak in older kernels
Not upstream as it is not needed there.
So a patch something like this might be a safe way to fix the
potential infoleak in older kernels.
THIS IS UNTESTED. It's a very obvious patch, though, so if it compiles
it probably works. It just initializes the output variable with 0 in
the inline asm description, instead of doing it in the exception
handler.
It will generate slightly worse code (a few unnecessary ALU
operations), but it doesn't have any interactions with the exception
handler implementation.
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e05 ("USB: serial: make minor allocation dynamic") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If we don't guarantee that we will always get an
interrupt at least when we're queueing our very last
request, we could fall into situation where we queue
every request with 'no_interrupt' set. This will
cause the link to get stuck.
The behavior above has been triggered with g_ether
and dwc3.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If UBIFS is facing an error while walking a directory, it reports this
error and ubifs_readdir() returns the error code. But the VFS readdir
logic does not make the getdents system call fail in all cases. When the
readdir cursor indicates that more entries are present, the system call
will just return and the libc wrapper will try again since it also
knows that more entries are present.
This causes the libc wrapper to busy loop for ever when a directory is
corrupted on UBIFS.
A common approach do deal with corrupted directory entries is
skipping them by setting the cursor to the next entry. On UBIFS this
approach is not possible since we cannot compute the next directory
entry cursor position without reading the current entry. So all we can
do is setting the cursor to the "no more entries" position and make
getdents exit.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
AZX_DCAPS_RIRB_PRE_DELAY is always tied with AZX_DCAPS_CTX_WORKAROUND,
which is Creative's XFi specific. So, we can replace it and reduce
one more bit free for DCAPS.
The stk1160 chip needs QUIRK_AUDIO_ALIGN_TRANSFER. This patch resolves
the issue reported on the mailing list
(http://marc.info/?l=linux-sound&m=139223599126215&w=2) and also fixes
bug 180071 (https://bugzilla.kernel.org/show_bug.cgi?id=180071).
Fix a short sprintf buffer in proc_keys_show(). If the gcc stack protector
is turned on, this can cause a panic due to stack corruption.
The problem is that xbuf[] is not big enough to hold a 64-bit timeout
rendered as weeks:
(gdb) p 0xffffffffffffffffULL/(60*60*24*7)
$2 = 30500568904943
That's 14 chars plus NUL, not 11 chars plus NUL.
Expand the buffer to 16 chars.
I think the unpatched code apparently works if the stack-protector is not
enabled because on a 32-bit machine the buffer won't be overflowed and on a
64-bit machine there's a 64-bit aligned pointer at one side and an int that
isn't checked again on the other side.
Reported-by: Ondrej Kozina <okozina@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Ondrej Kozina <okozina@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The function xfs_calc_dquots_per_chunk takes a parameter in units
of basic blocks. The kernel seems to get the units wrong, but
userspace got 'fixed' by commenting out the unnecessary conversion.
Fix both.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Line discipline drivers may mistakenly misuse ldisc-related fields
when initializing. For example, a failure to initialize tty->receive_room
in the N_GIGASET_M101 line discipline was recently found and fixed [1].
Now, the N_X25 line discipline has been discovered accessing the previous
line discipline's already-freed private data [2].
Harden the ldisc interface against misuse by initializing revelant
tty fields before instancing the new line discipline.
The advancing of the PC when completing an MMIO load is done before
re-entering the guest, i.e. before restoring the guest ASID. However if
the load is in a branch delay slot it may need to access guest code to
read the prior branch instruction. This isn't safe in TLB mapped code at
the moment, nor in the future when we'll access unmapped guest segments
using direct user accessors too, as it could read the branch from host
user memory instead.
Therefore calculate the resume PC in advance while we're still in the
right context and save it in the new vcpu->arch.io_pc (replacing the no
longer needed vcpu->arch.pending_load_cause), and restore it on MMIO
completion.
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[james.hogan@imgtec.com: Backport to 3.10..3.16] Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
As kvm_mips_complete_mmio_load() did not yet modify PC at this point
as James Hogans <james.hogan@imgtec.com> explained the curr_pc variable
and the comments along with it can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Link: http://lkml.org/lkml/2015/5/8/422 Cc: Gleb Natapov <gleb@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9993/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[james.hogan@imgtec.com: Backport to 3.10..3.16] Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate
TLB entries on the local CPU. This doesn't work correctly on an SMP host
when the guest is migrated to a different physical CPU, as it could pick
up stale TLB mappings from the last time the vCPU ran on that physical
CPU.
Therefore invalidate both user and kernel host ASIDs on other CPUs,
which will cause new ASIDs to be generated when it next runs on those
CPUs.
We're careful only to do this if the TLB entry was already valid, and
only for the kernel ASID where the virtual address it mapped is outside
of the guest user address range.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
[james.hogan@imgtec.com: Backport to 3.10..3.16] Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In USB20 specification, describes in chapter 9.4.5: The Remote Wakeup
field can be modified by the SetFeature() and ClearFeature() requests
using the DEVICE_REMOTE_WAKEUP feature selector.
In USB30 specification, also describes in chapter 9.4.5: The Function
Remote Wakeup field can be modified by the SetFeature() requests
using the FUNCTION_SUSPEND feature selector. In chapter 9.4.9 Set
Feature reference, it describes Function Remote Wake Enabled/Disabled
at suspend options by SET_FEATURE.
In USB30 specification only mentioned SetFeature(), so we need use
SET_FEATURE replace CLEAR_FEATURE to disable USB30 function remote
wakeup in suspend options.
We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.
[js] no ARCMSR_API_DATA_BUFLEN defined, use the number
Reported-by: Marco Grassi <marco.gra@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When we merge two contiguous partitions whose signatures are marked
NVRAM_SIG_FREE, We need update prev's length and checksum, then write it
to nvram, not cur's. So lets fix this mistake now.
Also use memset instead of strncpy to set the partition's name. It's
more readable if we want to fill up with duplicate chars .
Fixes: fa2b4e54d41f ("powerpc/nvram: Improve partition removal") Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When we call symbol__fixup_duplicate() we use algorithms to pick the
"best" symbols for cases where there are various functions/aliases to an
address, and those check zero size symbols, which, before calling
symbol__fixup_end() are _all_ symbols in a just parsed kallsyms file.
So first fixup the end, then fixup the duplicates.
Found while trying to figure out why 'perf test vmlinux' failed, see the
output of 'perf test -v vmlinux' to see cases where the symbols picked
as best for vmlinux don't match the ones picked for kallsyms.
Cc: Anton Blanchard <anton@samba.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 694bf407b061 ("perf symbols: Add some heuristics for choosing the best duplicate symbol") Link: http://lkml.kernel.org/n/tip-rxqvdgr0mqjdxee0kf8i2ufn@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently omap-rng checks the return value of pm_runtime_get_sync and
reports failure if anything is returned, however it should be checking
if ret < 0 as pm_runtime_get_sync return 0 on success but also can return
1 if the device was already active which is not a failure case. Only
values < 0 are actual failures.
Fixes: 61dc0a446e5d ("hwrng: omap - Fix assumption that runtime_get_sync will always succeed") Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The cipher block size for GCM is 16 bytes, and thus the CTR transform
used in crypto_gcm_setkey() will also expect a 16-byte IV. However,
the code currently reserves only 8 bytes for the IV, causing
an out-of-bounds access in the CTR transform. This patch fixes
the issue by setting the size of the IV buffer to 16 bytes.
Fixes: 84c911523020 ("[CRYPTO] gcm: Add support for async ciphers") Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The variable i contains a total number of resources (including
IORESOURCE_IRQ). However, we want the dmem_region_start to point
after the last resource of type IORESOURCE_MEM. The original behaviour
leads (very likely) to skipping several UIO mapping regions and makes
them useless. Fix this by computing dmem_region_start from the uiomem
which points to the last used UIO mapping.
Fixes: 0a0c3b5a24bd ("Add new uio device for dynamic memory allocation") Signed-off-by: Jan Viktorin <viktorin@rehivetech.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Without this patch irq_domain_disassociate() cannot properly release the
interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed'
but said bit is never cleared, only set.
Commit 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support")
added irq_map_generic_chip() function and also stated "This lacks a removal
function for now".
This commit provides an implementation of an unmap function that can be
called by irq_domain_disassociate().
[ tglx: Made the function static and removed the export as we have neither
a prototype nor a modular user. ]
[js] use irq_get_irq_data, irq_set_chip_and_handler, and
irq_set_chip_data in 3.12
Fixes: 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support") Signed-off-by: Sebastian Frias <sf84@laposte.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Mason <slash.tmp@free.fr> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
eeh_pe_bus_get() can return NULL if a PCI bus isn't found for a given PE.
Some callers don't check this, and can cause a null pointer dereference
under certain circumstances.
Fix this by checking NULL everywhere eeh_pe_bus_get() is called.
Fixes: 8a6b1bc70dbb ("powerpc/eeh: EEH core to handle special event") Signed-off-by: Russell Currey <ruscur@russell.cc> Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / thirdparty / kernel / stable.git / log
