SAE: Only allow SAE AKMP for PMKSA caching attempts
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.
SAE: Fix default PMK configuration for PMKSA caching case
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.
Clear pmk_len more consistently for extra protection
This gives more protection against unexpected behavior if RSN supplicant
code ends up trying to use sm->pmk[] with a stale value. Couple of the
code paths did not clear sm->pmk_len explicitly in cases where the old
PMK is being removed, so cover those cases as well to make sure these
will result in PMK-to-PTK derivation failures rather than use of
incorrect PMK value if such a code path could be reached somehow.
Fix hostapd wmm_enabled setup on config reload path
If there is no explicit wmm_enabled parameter in the configuration
(i.e., conf->wmm_enabled == -1), the configuration reload path needs to
initialize conf->wmm_enabled based on iconf->ieee80211n in
hostapd_reload_bss() similarly to what is done in the initial startup
case in hostapd_setup_bss().
This fixes issues with RSN capabilities being set incorrectly when WMM
is supposed to get enabled and unexpectedly enabling WMM when it is not
supposed to be enabled (HT disabled). Either of these issues could show
up when asking hostapd to reload the configuration file (and when that
file does not set wmm_enabled explicitly).
Michael Braun [Thu, 18 May 2017 13:21:54 +0000 (15:21 +0200)]
FT: Move wpa_ft_rrb_build_r0() special case to caller
Handle the special case of no PMK-R0 entry in the caller instead of
having to have wpa_ft_rrb_build_r0() aware of the possibility of pmk_r0
being NULL.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Michael Braun [Thu, 18 May 2017 13:21:54 +0000 (15:21 +0200)]
Fix potential memory leak with identity/radius_cui
ieee802_11_set_radius_info() might be called with a STA entry that has
already stored identity and/or radius_cui information, so make sure the
old values get freed before being replaced by the new ones.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Michael Braun [Thu, 18 May 2017 13:21:52 +0000 (15:21 +0200)]
tests: Add a small sleep in FT run_roams()
time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Michael Braun [Thu, 18 May 2017 13:21:50 +0000 (15:21 +0200)]
FT: Add expiration to PMK-R0 and PMK-R1 cache
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.
This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.
The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Michael Braun [Thu, 18 May 2017 13:21:50 +0000 (15:21 +0200)]
FT: Add helper function for FILS key storing
FILS calls wpa_ft_store_pmk_r0() from wpa_auth.c. This is moved into a
new function wpa_ft_store_pmk_fils() in preparation of additional
information being needed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Michael Braun [Thu, 18 May 2017 13:21:50 +0000 (15:21 +0200)]
FT: Convert r0_key_lifetime to seconds
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Remove CONFIG_IEEE80211R_AP=y build option from wpa_supplicant
There is no existing mechanism for setting up AP mode functionality with
FT enabled, so there is not really much point in having a build option
for trying to include the AP-to-AP FT functionality into wpa_supplicant
either. Since this build option results in failures to complete the
build, simply remove it completely. This can be restored if there is
ever desire to enable FT functionality in wpa_supplicant controlled AP
mode.
Davide Caratti [Wed, 28 Mar 2018 14:34:56 +0000 (16:34 +0200)]
wpa_supplicant: Don't reply to EAPOL if pkt_type is PACKET_OTHERHOST
When wpa_supplicant is running on a Linux interface that is configured in
promiscuous mode, and it is not a member of a bridge, incoming EAPOL
packets are processed regardless of the Destination Address in the frame.
As a consequence, there are situations where wpa_supplicant replies to
EAPOL packets that are not destined for it.
This behavior seems undesired (see IEEE Std 802.1X-2010, 11.4.a), and can
be avoided by attaching a BPF filter that lets the kernel discard packets
having pkt_type equal to PACKET_OTHERHOST.
Vasyl Vavrychuk [Mon, 12 Feb 2018 19:29:06 +0000 (21:29 +0200)]
Clean up setting of iface->p2p_mgmt flag
Previously we set this flag to one in wpa_supplicant_init_iface() if
Wi-Fi controller does not have a dedicated P2P-interface.
This setting had effect only in scope of wpa_supplicant_init_iface() and
it contradicts with comment to struct wpa_interface::p2p_mgmt field.
This comment says that this flag is used only if Wi-Fi controller has
dedicated P2P-device interface.
Also it contradicts with usage of similiar p2p_mgmt field in struct
wpa_supplicant. Again struct wpa_supplicant::p2p_mgmt is set only for
dedicated P2P-device interface.
After this change wpa_interface become input argument to
wpa_supplicant_init_iface() that we are not modifying.
Vasyl Vavrychuk [Mon, 12 Feb 2018 19:27:20 +0000 (21:27 +0200)]
dbus: Redirect signal processing to the management device if present
This fixes sending of FindStopped, GroupFormationFailure, and
InvitationReceived signals in the case of separate P2P-Device interface.
This extends the coverage of the earlier commit 745d62322b37675b4a7eb8f0cd10e25a288168da ("dbus: Redirect P2P request to
the managment device if present") to these three functions that were
missing the redirection.
Some wireless controllers might have separate P2P-Device interface, see
as example result of 'iw dev':
phy#0
Unnamed/non-netdev interface
...
type P2P-device
...
Interface wlp2s0
type managed
...
In this case there is separate 'struct wpa_supplicant' created for this
p2p-dev-* device as result of 'wpa_supplicant_add_iface >
wpas_p2p_add_p2pdev_interface > wpa_supplicant_add_iface'.
This instance of wpa_supplicant is not registered in D-Bus
(wpas_dbus_register_*) since for corresponding P2P device interface flag
'struct wpa_interface > p2p_mgmt' is set.
But this instance is saved in p2p_init_wpa_s and is used for handling
P2P related D-Bus commands. Therefore we should look for D-Bus path in
the parent of p2p_init_wpa_s instance.
Without this change test dbus_p2p_discovery starts failing if we set
support_p2p_device in vm-run.sh.
tests: Fix clearing of IGTK PN in handshake retransmit test functions
When locating the position of the IGTK PN in the key data, we also need
to skip the KDE header, in addition to the keyid field. This fixes
hostapd RESEND_M3 and RESEND_GROUP_M1 behavior when PMF is negotiated
for the association. Previously, the IGTK KDE ended up getting
practically hidden since zeroing of the PN ended up clearing the KDE OUI
and Type fields.
Ahmed ElArabawy [Thu, 15 Mar 2018 16:00:10 +0000 (09:00 -0700)]
Propagate the EAP method error code
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.
This commit reports the EAP method failure error code in a separate
callback.
The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.
Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
Jouni Malinen [Fri, 30 Mar 2018 09:11:55 +0000 (12:11 +0300)]
tests: WPA2-Enterprise connection using EAP-PSK after MAC address change
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
wpa_supplicant: Fix auth failure when the MAC is updated externally
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):
wpa_supplicant logs:
wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
wlan0: RSN: no matching PMKID found
EAPOL: Successfully fetched key (len=32)
WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 66 20 cf ab 8c dc
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
nl80211: Delete PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
nl80211: Add PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!
hostapd logs:
WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 02 00 00 00 00 00
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)
That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.
Add a new driver event that notifies of MAC address changes while the
interface is active.
Dmitry Lebed [Sat, 24 Mar 2018 07:54:27 +0000 (10:54 +0300)]
nl80211: Add DFS offload support using upstream nl80211 definitions
Add generic DFS offload support using the nl80211 feature that was
recently added to the mac80211-next tree. This uses the already
available DFS offload infrastructure that was previously used with
vendor specific definitions and just sets necessary flags (DFS_OFFLOAD
ext_feature) and forawrds CAC_STARTED event for processing.
Jouni Malinen [Mon, 26 Mar 2018 13:11:54 +0000 (16:11 +0300)]
tests: GAS/ANQP and Venue URL (hostapd venue_url)
Test the hostapd venue_url configuration parameter. In addition, fix the
previous defined gas_anqp_venue_url test case to use correct encoding of
the Venue URL ANQP-element payload (URLs were missing and Venue Number
was off-by-one).
Jouni Malinen [Mon, 26 Mar 2018 13:10:47 +0000 (16:10 +0300)]
Add hostapd.conf venue_url to set Venue URL ANQP-element
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.
Jouni Malinen [Sat, 24 Mar 2018 09:24:18 +0000 (11:24 +0200)]
FILS: Add more complete support for FT-FILS use cases
This extends the original IEEE Std 802.11ai-2016 functionality with the
changes added in REVmd to describe how additional keys are derived to
protect the FT protocol using keys derived through FILS authentication.
This allows key_mgmt=FT-FILS-SHA256 to be used with FT protocol since
the FTE MIC can now be calculated following the changes in REVmd. The
FT-FILS-SHA384 case is still unsupported (it needs support for variable
length MIC field in FTE).
Jouni Malinen [Sat, 24 Mar 2018 16:45:42 +0000 (18:45 +0200)]
FT: Derive PMK-R1 locally if requested PMKR0Name is found
Derive PMK-R1 locally if the derived PMKR1Name is not found from the
local cache, but the request is for a key that was originally generated
locally (R0KH-ID matches) and the PMKR0Name is found in the local cache.
This was apparently not hit in the previously used FT sequences, but
this is useful to have available if a PMK-R1 entry is dropped from the
local cache before PMK-R0.
Jouni Malinen [Fri, 23 Mar 2018 15:57:14 +0000 (17:57 +0200)]
SAE: Fix PTK derivation to use KDF-SHA256
The previous implementation ended up defaulting to using PRF-SHA1 for
deriving PTK from PMK when SAE was used. This is not correct since the
SAE AKM is defined to be using SHA-256 -based KDF instead. Fix that.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Jouni Malinen [Fri, 23 Mar 2018 15:45:44 +0000 (17:45 +0200)]
SAE: Fix PMKID in EAPOL-Key msg 1/4
Previously, the association that used SAE authentication ended up
recalculating the PMKID for EAPOL-Key msg 1/4 using incorrect
PMK-to-PMKID derivation instead of using the previously derived PMKID
from SAE. The correct PMKID was used only when going through PMKSA
caching exchange with a previously derived PMKSA from SAE.
Fix this by storing the SAE PMKID into the state machine entry for the
initial SAE authentication case when there is no explicit PMKSA entry
attached to the station.
Jouni Malinen [Fri, 23 Mar 2018 16:42:21 +0000 (18:42 +0200)]
SAE: Fix FT-SAE key derivation for a case where PMKID in msg 1/4 matches
Previously, matching PMKSA cache entry ended up clearing XXKey. However,
that XXKey is needed in the specific case where FT-SAE goes through the
initial mobility domain association with SAE authentication. FT-SAE
worked previously since the hostapd side generation of the particular
PMKID value in msg 1/4 was broken, but once that PMKID is fixed,
wpa_supplicant will need this fix to allow FT-SAE to be used.
Jouni Malinen [Wed, 21 Mar 2018 20:34:09 +0000 (22:34 +0200)]
Fix a resource leak on hostapd maclist parsing error path
The open file needs to be closed in error case. The conversion to using
a new helper function (hostapd_add_acl_maclist) somehow managed to
remove the neede fclose(f) call. Bring it back to fix this.
Fixes: 3988046de538 ("hostapd: Dynamic MAC ACL management over control interface") Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Jouni Malinen [Wed, 21 Mar 2018 14:58:05 +0000 (16:58 +0200)]
Do not disable 40 MHz based on co-ex report with matching primary channel
When processing 20/40 BSS Coexistence Management frames that do not
explicitly require 40 MHz to be disabled, check whether the reported
channels in 20/40 BSS Intolerant Channel Report element match the
current primary channel. If so, allow 40 MHz operation to continue. This
makes the during-operation updates for 20/40 Operation Permitted more
consistent with the scans during initial BSS startup.
The received 20/40 BSS Intolerant Channel Report channels are to be used
in the OT set in the during-operation determination and the P == OT_i
exception was ignored in the previous implementation which could result
in the AP first starting with 40 MHz and then dropping to 20 MHz on
first received 20/40 BSS Coexistence Management frame even though there
was no change in the neighboring BSSs.
Jouni Malinen [Wed, 21 Mar 2018 14:43:54 +0000 (16:43 +0200)]
Support multiple 20/40 BSS Intolerant Channel Report elements
This extends 20/40 BSS Coexistence Management frame processing to
iterate over all the included 20/40 BSS Intolerant Channel Report
elements instead of using only the first one.
Jouni Malinen [Wed, 21 Mar 2018 14:35:15 +0000 (16:35 +0200)]
Ignore intra-BSS 20/40 BSS Coexistence Management from not-associated STA
The 20 MHz BSS Width Request field is set to 1 only for intra-BSS
reports. As such, ignore the frame if such a claim is made by a
transmitter that is not currently associated with the AP.
hostapd: Ignore LOW_ACK event for co-operative steering clients
Ignore hostapd_event_sta_low_ack for a station which has agreed to
steering by checking the agreed_to_steer flag. This flag will be set
whenever a station accepts the BSS transition request from the AP.
Without this ignoring of the LOW_ACK event, the steering in-progress
might be affected due to disassociation. In this way AP will allow some
time (two seconds) for the station to move away and reset the flag after
the timeout.
Tamizh chelvam [Fri, 9 Mar 2018 12:49:09 +0000 (18:19 +0530)]
Make STA opmode change event available to upper layers
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Tamizh chelvam [Fri, 9 Mar 2018 12:49:08 +0000 (18:19 +0530)]
nl80211: Add support for STA opmode change events
The nl80211 driver can report STA_OPMODE notification event as soon as
it receives an HT/VHT Action frame about modification of station's SMPS
mode/bandwidth/RX NSS. Add support to parse such events.
hostapd: Add last_ack_rssi into ctrl iface cmd STA
This allows external application to get last ACK signal strength of the
last transmitted frame if the driver makes this information
(NL80211_STA_INFO_ACK_SIGNAL) available.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org> Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Ashok Ponnaiah [Mon, 5 Mar 2018 05:29:18 +0000 (10:59 +0530)]
OWE: Clean up pointer check in a testing code path
Check wpa_auth_write_assoc_resp_owe() return value to keep static
analyzers happier. The code path where this could happen is not really
reachable due to the separate hapd->conf->own_ie_override check and
wpa_auth_write_assoc_resp_owe() returning NULL only in an error case in
the override path. Furthermore, clean up the pointer return value to use
a proper pointer (NULL vs. 0).
DPP: Support retrieving of configurator's private key
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Jouni Malinen [Fri, 16 Mar 2018 11:04:15 +0000 (13:04 +0200)]
SAE: Fix EAPOL-Key integrity and key-wrap algorithm selection
The SAE AKM 00-0F-AC:8 is supposed to use EAPOL-Key Key Descriptor
Version 0 (AKM-defined) with AES-128-CMAC and NIST AES Key Wrap.
However, the previous implementation ended up using Key Descriptor
Version 2 (HMAC-SHA-1-128 and NIST AES Key Wrap). Fix this by using the
appropriate Key Descriptor Version and integrity algorithm. Use helper
functions to keep the selection clearer and more consistent between
wpa_supplicant and hostapd uses.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Srinivas Dasari [Wed, 7 Mar 2018 11:56:26 +0000 (17:26 +0530)]
DPP: Extend dpp_test 89 functionality to transmit side
This extends dpp_test functionality to allow DPP exchanges to be stopped
after authentication is completed on the Initiator, i.e., after sending
out the Authentication Confirm message. Previously, dpp_test=89 was used
only on the Responder side to stop after receiving the Authentication
Confirm message. The main use case for this extended functionality is to
be able to stop the protocol exchange on a device that acts as
authentication Initiator and Enrollee.
Use correct WPA_ALG_* values to compare for enum wpa_alg
enum wpa_alg was being compared with WPA_CIPHER_* values. That does not
work here and strict compilers will report this as an error. Fix the
comparision to use proper WPA_ALG_* values. This fixes testing
capability for resetting IPN for BIP.
Fixes: 16579769ff7b ("Add testing functionality for resetting PN/IPN for configured keys") Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Jouni Malinen [Sun, 11 Mar 2018 15:04:34 +0000 (17:04 +0200)]
mka: Mark ieee802_1x_kay_create_mka() ckn and cak arguments const
These structures are not modified or freed (i.e., only data from them is
copied), so mark the arguments const to document this a bit more clearly
now that there was a memory leak in one of the callers to this function.
Davide Caratti [Thu, 8 Mar 2018 16:15:02 +0000 (17:15 +0100)]
wpa_supplicant: Fix memory leaks in ieee802_1x_create_preshared_mka()
In case MKA is initialized successfully, local copies of CAK and CKN
were allocated, but never freed. Ensure that such memory is released
also when ieee802_1x_kay_create_mka() returns a valid pointer.
Mike Siedzik [Tue, 20 Feb 2018 19:28:40 +0000 (14:28 -0500)]
mka: Do not print contents of SAK to debug log
Log newly generated SAKs as well as unwrapped SAKs with wpa_hexdump_key()
rather than wpa_hexdump(). By default, the wpa_hexdump_key() function
will not display sensitive key data.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Mike Siedzik [Tue, 20 Feb 2018 19:28:37 +0000 (14:28 -0500)]
mka: Detect duplicate MAC addresses during key server election
In the unlikely event the local KaY and the elected peer have the same
actor priority as well as the same MAC address, log a warning message
and do not elect a key server. Resolution is for network administrator
to reconfigure MAC address.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Mike Siedzik [Tue, 20 Feb 2018 19:28:34 +0000 (14:28 -0500)]
mka: Loss of live peers to result in connect PENDING not AUTHENTICATED
When the number of live peers becomes 0 the KaY was setting
kay->authenticated true and telling the CP to connect AUTHENTICATED.
Per IEEE Std 802.1X-2010 Clause 12.2, MKA.authenticated means "the Key
Server has proved mutual authentication but has determined that
Controlled Port communication should proceed without the use of MACsec",
which means port traffic will be passed in the clear.
When the number of live peers becomes 0 the KaY must instead set
kay->authenticated false and tell the CP to connect PENDING. Per Clause
12.3 connect PENDING will "prevent connectivity by clearing the
controlledPortEnabled parameter."
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Mike Siedzik [Tue, 20 Feb 2018 19:28:32 +0000 (14:28 -0500)]
mka: Ignore MACsec SAK Use Old Key parameter if we don't have our old key
Upon receipt of the "MACsec MKPDU SAK Use parameter set" the KaY verifies
that both the latest key and the old key are valid. If the local system
reboots or is reinitialized, the KaY won't have a copy of its old key.
Therefore if the KaY does not have a copy of its old key it should not
reject MKPDUs that contain old key data in the MACsec SAK Use parameter.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Mike Siedzik [Tue, 20 Feb 2018 19:28:31 +0000 (14:28 -0500)]
mka: When matching CKNs ensure that lengths are identical
KaY looks up participants using CAK Name (CKN). Per IEEE Std 802.1X-2010
Clause 9.3.1 CAK identification, the CKN is an integral number of
octets, between 1 and 32 (inclusive). This fix will ensure that the KaY
does not inadvertently match CKNs such as 'myCakNamedFoo' and
'myCakNamedFooBar'.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Tamizh chelvam [Wed, 14 Feb 2018 13:43:56 +0000 (19:13 +0530)]
Extend ACL check for Probe Request frames
Extend ACL check to deny Probe Request frames for the client which does
not pass ACL check. Skip this check for the case where RADIUS ACL is
used to avoid excessive load on the RADIUS authentication server due to
Probe Request frames. This patch add wpa_msg event for auth and assoc
rejection due to acl reject.
Add new WiFi test config attributes to configure BA params
Define a new WiFi test configuration attributes in QCA vendor
command to configure BA session parameters and to add or
delete a BA session and to configure no ack policy.
This is used for configuring the testbed device.
Add new WiFi test config attribute to allow WEP/TKIP in HE
Define a new WiFi test configuration attribute in QCA vendor
command to allow or not to allow WEP/TKIP in HT/VHT/HE mode.
This is used for configuring the testbed device.
Jeffin Mammen [Fri, 2 Mar 2018 19:10:38 +0000 (21:10 +0200)]
FILS: Check kde more consistently to avoid static analyzer warnings
For FILS, __wpa_send_eapol() is called only with the kde != NULL, but a
static analyzer might not understand that. Add an explicit check kde !=
NULL similarly to the other cases going through the kde parameter to
silence such bogus warnings.
Jouni Malinen [Fri, 2 Mar 2018 10:29:30 +0000 (12:29 +0200)]
SAE: Debug print group support in the crypto library
This makes it easier to understand why "SAE: Failed to select group"
debug entry shows up in cases the selected crypto library does not
support a specific group.
Jouni Malinen [Fri, 2 Mar 2018 10:13:16 +0000 (12:13 +0200)]
SAE: Fix potential infinite loop in mismatching PMK case on AP
Commit e61fea6b467bec0702096c795b06195584d32a6c ('SAE: Fix PMKSA caching
behavior in AP mode') modified the PSK fetching loop to not override PMK
in case of SAE with PMKSA caching. However, that commit missed the error
path cases where there is need to break from the loop with exact
negative of the check in the beginning of the loop. This could result in
hitting an infinite loop in hostapd if a station derived a different PMK
value from otherwise successfully completed SAE authentication or if a
STA used a different PMK with a PMKSA caching attempt after a previously
completed successful authentication.
Fix this by adding the matching break condition on SAE AKM within the
loops.
Fixes: e61fea6b467b ("SAE: Fix PMKSA caching behavior in AP mode") Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Anurag Das [Fri, 23 Feb 2018 10:14:02 +0000 (15:44 +0530)]
wpadebug: Add activity to select method for QR Code scanning
Add QrCodeReadActivity that makes a decision to select between InputUri
and QrCodeScannerActivity depending on the availability of the camera in
the device.
Anurag Das [Wed, 21 Feb 2018 12:35:33 +0000 (18:05 +0530)]
wpadebug: A dialog activity to input the URI from QR Code Scanner
This should help to read the URI from the QR Code Scanner's (USB HID
devices instead of USB video device) that decodes the QR Code.
This dialog box provisions the mechanism to enter the decoded
URI code from such hardware devices.
This dialog can be used with:
am start -n w1.fi.wpadebug/w1.fi.wpadebug.InputUri
projects / thirdparty / hostap.git / log
