Jeff Kletsky [Wed, 4 Jan 2023 07:17:03 +0000 (23:17 -0800)]
ipq40xx: Fix Linksys upgrade, restore config step
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration
was not preserved over sysupgrade steps.
This was restored for some devices in
commit 84ff6c90dda1 ("base-files: bring back nand_do_upgrade_success").
This restored preservation of config for ipq40xx devices using the
linksys.sh script. Other devices and targets have not been examined.
Closes: #11677 Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Tested-on: EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
(checkpatch nitpick) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
David Bauer [Mon, 13 Mar 2023 02:14:42 +0000 (03:14 +0100)]
mediatek: enable bootargs-override for filogic subtarget
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.
David Bauer [Sat, 11 Mar 2023 00:38:19 +0000 (01:38 +0100)]
generic: mxl-gpy: allow configuring LED registers
Add a patch to allow modification of the PHY LED configuration. This is
required for boards, where the reset configuration of LED functions is
incompatibe with the usage of the device LEDs.
This is the case for the ASUS TUF-AX4200 Wireless router. It requires
modification of the LED configuration because as the WAN LED on the
front of the device is driven by the PHY. Without patching, it would
only illuminate in case the Link speed is 100 Mbit/s.
Felix Fietkau [Sun, 19 Feb 2023 14:01:43 +0000 (15:01 +0100)]
kernel: add support for threaded network backlog processing
This can improve load balancing by pushing backlog (and RPS) processing
to separate threads, allowing the scheduler to distribute the load.
It can be enabled with: echo 1 > /proc/sys/net/core/backlog_threaded
David Bauer [Thu, 23 Mar 2023 22:53:47 +0000 (23:53 +0100)]
ramips: add support for Mercusys MR70X
Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
Do not connect 3v3. TX is marked with an arrow.
Installation
============
Flash factory image. This can be done using stock web ui.
Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.
Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1
Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net>
These patches have now received a positive review upstream, so let's add them
to pending patches.
776-net-dsa-b53-mmap-add-phy-ops.patch:
This is mostly bmips/bcm63xx-specific to get external switches working
without hanging the device when accessing certain registers.
777-net-dsa-b53-mdio-add-support-for-BCM53134:
This adds support for BCM53134 switch on DSA B53, so any target using DSA B53
can benefit from it.
Also fix sercomm-h500-s external switch IMP port phy-mode.
Refreshing the patches for fff07085fb5a moved the b53_adjust_63xx_rgmii() call
from b53_phylink_mac_link_up() to b53_phylink_mac_link_down().
In order to properly configure the RGMII ports we need to restore it to its
correct place.
Lech Perczak [Tue, 7 Mar 2023 20:25:59 +0000 (21:25 +0100)]
ath79: support Ruckus ZoneFlex 7341/7343/7363
Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point. ZoneFlex 7343 is the single band variant of 7363
restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet
ports.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch,
connected with Fast Ethernet link to CPU.
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the -U variants.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single PH1 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed.
Use the Gigabit interface, Fast Ethernet ports are not supported
under U-boot:
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7363_backup.bin
4. System will reboot.
Quirks and known issues:
- Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management
features of the RTL8363S switch aren't implemented yet, though the
switch is visible over MDIO0 bus. This is a gigabit-capable switch, so
link establishment with a gigabit link partner may take a longer time
because RTL8363S advertises gigabit, and the port magnetics don't
support it, so a downshift needs to occur. Both ports are accessible
at eth1 interface, which - strangely - runs only at 100Mbps itself.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Lech Perczak [Fri, 30 Dec 2022 23:15:48 +0000 (00:15 +0100)]
ath79: support Ruckus ZoneFlex 7351
Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7351-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7351_backup.bin
4. System will reboot.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Sercomm H-500s is a BCM63268 with 128M, internal and external (Quantenna) wifi
and external BCM53134S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/sercomm/h500-s.
It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.
kernel: add pending patches for bcm63268-timer-clocks
bcm63268-timer-clocks have been sent upstream with a positive review, so let's
add them to pending v5.15.
Also add devm_clk_hw_register_gate() patch from v5.17 to backports since it's
needed for upstream bcm63268-timer-clocks patches.
7c0f603 router: skip RA and wait for LINK-LOCAL to be assigned ba30afc config: skip interface setup if interface not IFF_RUNNING 06b111e Revert "odhcpd: Reduce error messages" 90d6cc9 odhcpd: Reduce error messages
Also drop AUTORELEASE since it got deprecated.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CI: build: disable cache of external toolchain/sdk
Our buildbot build a different external toolchain/sdk for each build.
This cause the idea of using the tar hash to cache it broken and wrong.
This makes the github cache bloated and remove space for ccache cache.
Drop cache for external toolchain/sdk as the feature is broken and cause
problems to ccache cache.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes the following warnings for Netgear DGND3700v2 and Comtrend VR-3032u:
[ 1.059540] 7 fixed-partitions partitions found on MTD device brcmnand.0
[ 1.066570] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.073766] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.081927] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.089128] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
Huawei HG253s v2 is a BCM6362 with 128M RAM, internal wifi and external
BCM53124S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/huawei/hg253s_v2.
It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.
Without this change, internal and external B53 switches couldn't coexist as
reported in https://github.com/openwrt/openwrt/issues/10313.
In order to fix this we need to force the B53 MMAP DSA switch driver to use
bcm6368-mdio-mux for accessing the PHY registers instead of its own phy_read()
and phy_write() functions.
Andre Heider [Thu, 2 Feb 2023 20:33:38 +0000 (21:33 +0100)]
treewide: add support for "lto" in PKG_BUILD_FLAGS
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Andre Heider [Thu, 2 Feb 2023 20:16:21 +0000 (21:16 +0100)]
treewide: add support for "gc-sections" in PKG_BUILD_FLAGS
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Andre Heider [Thu, 2 Feb 2023 18:20:42 +0000 (19:20 +0100)]
build: introduce PKG_BUILD_FLAGS and move PKG_IREMAP to it
PKG_BUILD_FLAGS is a new variable for package Makefiles similar to
PKG_FLAGS. It's a whitespace separated list of flags to control various
aspects of how a package is build.
The build system and/or .config defines the default for each, but
every package has the means to override it. Using $flagname enables
a flag, no-$flagname disables it.
Start with PKG_IREMAP as "iremap". That's easy as no package here
nor in any package feed uses it. The default is unchanged: enabled.
Packages can opt-out via:
PKG_BUILD_FLAGS:=no-iremap
(Not that any should, just to illustrate how to use it)
Robert Marko [Tue, 30 Jun 2020 16:07:50 +0000 (18:07 +0200)]
ipq40xx: add support for Wallystech DR40x9
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Cases have been reported in which certain devices do not boot correctly
or have errors. After various tests by users who have such errors it has
been concluded that the SPI frequency should be reduced to 40Mhz, at
this speed it appears that all devices work correctly.
Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
John Audia [Sat, 11 Mar 2023 19:03:00 +0000 (14:03 -0500)]
x86: fix deprecated CONFIG_MICROCODE_OLD_INTERACE
We use late loading[1] so need to set this option despite upstream adding a
kernel taint when this option is set. See discussion in PR#12149 for more details.
David Bauer [Mon, 20 Mar 2023 16:27:58 +0000 (17:27 +0100)]
mpc85xx: poll PHY status
Disable interrupts for the eth-PHYs, as the interrupts are either not
firing or lost within the stack. Switch to polling the PHY status in the
meantime until a proper fix is implemented.
David Bauer [Mon, 20 Mar 2023 03:50:14 +0000 (04:50 +0100)]
mpc85xx: use bootwrapper for ws-ap3825i
The boot-procedure for the Extreme WS-AP3825I is vfragile to put it
mildly. It does not relocate the FDT properly. It currently exercises
every step manually as well as coming with a pre-padded dtb.
Use the PowerPC bootwrapper code for legacy platforms with a pre-filles
DTS instead. We still need to ship a fit image to not break the fdt
resize / relocate instructions on existing boards. This does not require
adapting the U-Boot bootcommand.
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
David Bauer [Sun, 19 Mar 2023 20:33:32 +0000 (21:33 +0100)]
mpc85xx: fix incorrect kernel target
The wrapper-image for the WL-WDR4900 was used as a build-target for the
kernel. This workd fine as long as only a single wrapper is used with
the OpenWrt build-system.
If additional wrappers are used, the build becomes racy in the
wrapper-stage.
The wrapper images actually do not represent a target. They are built
based on the kernel configuration. Only copy the resulting images to
avoid race-conditions as explained.
Hauke Mehrtens [Wed, 8 Mar 2023 20:31:19 +0000 (21:31 +0100)]
kernel: Deactivate options shown with CONFIG_KERNEL_KCOV=y
This sets the CONFIG_KCOV_IRQ_AREA_SIZE kernel configuration option to its default value.
This is shown when I set CONFIG_KERNEL_KCOV=y in the OpenWrt configuration on x86/64.
Hauke Mehrtens [Wed, 8 Mar 2023 20:31:17 +0000 (21:31 +0100)]
kernel: Set some options to default shown with CONFIG_KERNEL_UBSAN=y
This sets some kernel configuration options to their default values. I saw
these as warnings when I set CONFIG_KERNEL_UBSAN=y is set in the OpenWrt
configuration on x86/64.
Mathew McBride [Thu, 23 Feb 2023 05:51:36 +0000 (16:51 +1100)]
tools: update elf.h
OpenWrt contains a 2012 copy of glibc's elf.h, which predates the
introduction of some newer architectures like Arm64 and RISC-V.
Linux 5.13 introduced the "gen-hyprel" tool into the kernel compile
(when virtualization/KVM is enabled) which requires EM_AARCH64 to be
defined.
arch/arm64/kvm/hyp/nvhe/gen-hyprel.c: In function 'init_elf':
arch/arm64/kvm/hyp/nvhe/gen-hyprel.c:289:43: error: 'EM_AARCH64'
undeclared (first use in this function); did you mean 'EM_IA_64'?
289 | assert_eq(elf16toh(elf.ehdr->e_machine), EM_AARCH64, "%u");
| ^~~~~~~~~~
Update the copy of elf.h from the latest glibc to fix this.
Compile-tested: ath79, armvirt, mpc85xx, x86
Run-tested: armvirt
Kristjan Krušič [Sat, 4 Feb 2023 16:00:57 +0000 (17:00 +0100)]
ipq806x: add support for Nokia Airscale AC400i
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
lantiq: xway: add phy reset pin to AVM Fritz!Box 7320
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
John Audia [Mon, 13 Mar 2023 13:04:36 +0000 (09:04 -0400)]
kernel: bump 5.15 to 5.15.102
No patches needed to be rebased.
Signed-off-by: John Audia <therealgraysky@proton.me> Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36 Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
projects / thirdparty / openwrt.git / log
