Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.
Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.
RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:
Some of the transport addresses of a multi-homed SCTP endpoint
may become inactive due to either the occurrence of certain
error conditions (see Section 8.2) or adjustments from the
SCTP user.
When there is outbound data to send and the primary path
becomes inactive (e.g., due to failures), or where the SCTP
user explicitly requests to send data to an inactive
destination transport address, before reporting an error to
its ULP, the SCTP endpoint should try to send the data to an
alternate __active__ destination transport address if one
exists.
When retransmitting data that timed out, if the endpoint is
multihomed, it should consider each source-destination address
pair in its retransmission selection policy. When retransmitting
timed-out data, the endpoint should attempt to pick the most
divergent source-destination pair from the original
source-destination pair to which the packet was transmitted.
Note: Rules for picking the most divergent source-destination
pair are an implementation decision and are not specified
within this document.
So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.
Commit 4141ddc02a92 ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc02a92, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.
Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.
This patch mostly reverts 4141ddc02a92, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.
Fixes: 4141ddc02a92 ("sctp: retran_path update bug fix") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com> Acked-by: Vlad Yasevich <yasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[wt: picked updated function from 3.12 except the debug statement] Signed-off-by: Willy Tarreau <w@1wt.eu>
We fixed this to use free_netdev() instead of kfree() but unfortunately
free_netdev() doesn't accept NULL pointers. Smatch complains about
this, it's not something I discovered through testing.
Fixes: 3030d40b5036 ('staging: vt6655: use free_netdev instead of kfree') Fixes: 0a438d5b381e ('staging: vt6656: use free_netdev instead of kfree') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[wt: only vt6656 was converted to free_netdev in 3.10] Signed-off-by: Willy Tarreau <w@1wt.eu>
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[wt: no tuntap VLAN offloading in 3.10] Signed-off-by: Willy Tarreau <w@1wt.eu>
KGDB is a kernel debug stub and it can't be used to debug userland as it
can only safely access kernel memory.
On MIPS however KGDB has always got the register state of sleeping
processes from the userland register context at the beginning of the
kernel stack. This is meaningless for kernel threads (which never enter
userland), and for user threads it prevents the user seeing what it is
doing while in the kernel:
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) 0x0000000000000000 in ?? ()
2 Thread 1 (init) 0x000000007705c4b4 in ?? ()
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Get the register state instead from the (partial) kernel register
context stored in the task's thread_struct for resume() to restore. All
threads now correctly appear to be in context_switch():
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Call clobbered registers which aren't saved and exception registers
(BadVAddr & Cause) which can't be easily determined without stack
unwinding are reported as 0. The PC is taken from the return address,
such that the state presented matches that found immediately after
returning from resume().
Fixes: 8854700115ec ("[MIPS] kgdb: add arch support for the kernel's kgdb core") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15829/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Take a reference on the sessions returned by l2tp_session_find_nth()
(and rename it l2tp_session_get_nth() to reflect this change), so that
caller is assured that the session isn't going to disappear while
processing it.
For procfs and debugfs handlers, the session is held in the .start()
callback and dropped in .show(). Given that pppol2tp_seq_session_show()
dereferences the associated PPPoL2TP socket and that
l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to
call the session's .ref() callback to prevent the socket from going
away from under us.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Fixes: 0ad6614048cf ("l2tp: Add debugfs files for dumping l2tp debug info") Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: Willy Tarreau <w@1wt.eu>
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d984 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.") Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: Brad Mouring <brad.mouring@ni.com> Acked-by: Xander Huff <xander.huff@ni.com> Acked-by: Kyle Roeschley <kyle.roeschley@ni.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Since 09d9686047db ("netfilter: x_tables: do compat validation via
translate_table"), it used compatr structure to assign newinfo
structure. In translate_compat_table of ip_tables.c and ip6_tables.c,
it used compatr->hook_entry to replace info->hook_entry and
compatr->underflow to replace info->underflow, but not do the same
replacement in arp_tables.c.
It caused invoking 32-bit "arptbale -P INPUT ACCEPT" failed in 64bit
kernel.
--------------------------------------
root@qemux86-64:~# arptables -P INPUT ACCEPT
root@qemux86-64:~# arptables -P INPUT ACCEPT
ERROR: Policy for `INPUT' offset 448 != underflow 0
arptables: Incompatible with this kernel
--------------------------------------
Fixes: 09d9686047db ("netfilter: x_tables: do compat validation via translate_table") Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
I noticed that reading the snapshot file when it is empty no longer gives a
status. It suppose to show the status of the snapshot buffer as well as how
to allocate and use it. For example:
># cat snapshot
# tracer: nop
#
#
# * Snapshot is allocated *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
What happened was that it was using the ring_buffer_iter_empty() function to
see if it was empty, and if it was, it showed the status. But that function
was returning false when it was empty. The reason was that the iter header
page was on the reader page, and the reader page was empty, but so was the
buffer itself. The check only tested to see if the iter was on the commit
page, but the commit page was no longer pointing to the reader page, but as
all pages were empty, the buffer is also.
Fixes: 651e22f2701b ("ring-buffer: Always reset iterator to reader page") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Currently the snapshot trigger enables the probe and then allocates the
snapshot. If the probe triggers before the allocation, it could cause the
snapshot to fail and turn tracing off. It's best to allocate the snapshot
buffer first, and then enable the trigger. If something goes wrong in the
enabling of the trigger, the snapshot buffer is still allocated, but it can
also be freed by the user by writting zero into the snapshot buffer file.
Also add a check of the return status of alloc_snapshot().
Fixes: 77fd5c15e3 ("tracing: Add snapshot trigger to function probes") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023e5 ("powerpc: Setup in HFSCR for POWER8") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[sb: Backported to linux-4.4.y: adjusted context] Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
According to full-history-linux commit d3794f4fa7c3edc3 ("[PATCH] M68k
update (part 25)"), port operations are allowed on m68k if CONFIG_ISA is
defined.
However, commit 153dcc54df826d2f ("[PATCH] mem driver: fix conditional
on isa i/o support") accidentally changed an "||" into an "&&",
disabling it completely on m68k. This logic was retained when
introducing the DEVPORT symbol in commit 4f911d64e04a44c4 ("Make
/dev/port conditional on config symbol").
Drop the bogus dependency on !M68K to fix this.
Fixes: 153dcc54df826d2f ("[PATCH] mem driver: fix conditional on isa i/o support") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Al Stone <ahs3@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
In function mlx4_cq_completion() and mlx4_cq_event(), the
radix_tree_lookup requires a rcu_read_lock.
This is mandatory: if another core frees the CQ, it could
run the radix_tree_node_rcu_free() call_rcu() callback while
its being used by the radix tree lookup function.
Additionally, in function mlx4_cq_event(), since we are adding
the rcu lock around the radix-tree lookup, we no longer need to take
the spinlock. Also, the synchronize_irq() call for the async event
eliminates the need for incrementing the cq reference count in
mlx4_cq_event().
Other changes:
1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock:
we no longer take this spinlock in the interrupt context.
The spinlock here, therefore, simply protects against different
threads simultaneously invoking mlx4_cq_free() for different cq's.
2. In function mlx4_cq_free(), we move the radix tree delete to before
the synchronize_irq() calls. This guarantees that we will not
access this cq during any subsequent interrupts, and therefore can
safely free the CQ after the synchronize_irq calls. The rcu_read_lock
in the interrupt handlers only needs to protect against corrupting the
radix tree; the interrupt handlers may access the cq outside the
rcu_read_lock due to the synchronize_irq calls which protect against
premature freeing of the cq.
3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg.
4. We leave the cq reference count mechanism in place, because it is
still needed for the cq completion tasklet mechanism.
Fixes: 6d90aa5cf17b ("net/mlx4_core: Make sure there are no pending async events when freeing CQ") Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Reorder the operations in decompress_kernel() to ensure initrd is moved
to a safe location before the bss section is zeroed.
During decompression bss can overlap with the initrd and this can
corrupt the initrd contents depending on the size of the compressed
kernel (which affects where the initrd is placed by the bootloader) and
the size of the bss section of the decompressor.
Also use the correct initrd size when checking for overlaps with
parmblock.
The rapf copy loops in the Meta usercopy code is missing some extable
entries for HTP cores with unaligned access checking enabled, where
faults occur on the instruction immediately after the faulting access.
Add the fixup labels and extable entries for these cases so that corner
case user copy failures don't cause kernel crashes.
The fixup code to rewind the source pointer in
__asm_copy_from_user_{32,64}bit_rapf_loop() always rewound the source by
a single unit (4 or 8 bytes), however this is insufficient if the fault
didn't occur on the first load in the loop, as the source pointer will
have been incremented but nothing will have been stored until all 4
register [pairs] are loaded.
Read the LSM_STEP field of TXSTATUS (which is already loaded into a
register), a bit like the copy_to_user versions, to determine how many
iterations of MGET[DL] have taken place, all of which need rewinding.
The fixup code for the copy_to_user rapf loops reads TXStatus.LSM_STEP
to decide how far to rewind the source pointer. There is a special case
for the last execution of an MGETL/MGETD, since it leaves LSM_STEP=0
even though the number of MGETLs/MGETDs attempted was 4. This uses ADDZ
which is conditional upon the Z condition flag, but the AND instruction
which masked the TXStatus.LSM_STEP field didn't set the condition flags
based on the result.
Fix that now by using ANDS which does set the flags, and also marking
the condition codes as clobbered by the inline assembly.
When copying to userland on Meta, if any faults are encountered
immediately abort the copy instead of continuing on and repeatedly
faulting, and worse potentially copying further bytes successfully to
subsequent valid pages.
Fix the error checking of the alignment adjustment code in
raw_copy_from_user(), which mistakenly considers it safe to skip the
error check when aligning the source buffer on a 2 or 4 byte boundary.
If the destination buffer was unaligned it may have started to copy
using byte or word accesses, which could well be at the start of a new
(valid) source page. This would result in it appearing to have copied 1
or 2 bytes at the end of the first (invalid) page rather than none at
all.
In case of error, the function kthread_run() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against
__TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end
of a PTRACE_LISTEN, this can wake the task /after/ the check against
__TASK_TRACED, but before the reset of state to TASK_TRACED. This
causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup
against TRACED while the task is still on the rq wake_list, corrupting
it.
Oleg said:
"The kernel can crash or this can lead to other hard-to-debug problems.
In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced()
assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the
contract. Obviusly it is very wrong to manipulate task->state if this
task is already running, or WAKING, or it sleeps again"
[akpm@linux-foundation.org: coding-style fixes] Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL") Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com Signed-off-by: Ben Segall <bsegall@google.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.
If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a5344f ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.
The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 52ad353a5344f "(igmp: fix the problem when mc leave group") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a71bb ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
This patch fixes a bug introduced by commit 977dcfdc6031 ("USB: OHCI:
don't lose track of EDs when a controller dies"). The commit changed
ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had
been called. The user-visible consequence is that the driver
occasionally crashes or locks up when an URB is submitted while
another URB for the same endpoint is being unlinked.
This patch moves the ED state change later, to the right place. The
drawback is that now we may unnecessarily execute some instructions
multiple times when a controller dies. Since controllers dying is an
exceptional occurrence, a little wasted time won't matter.
This effectively reverts the following three commits:
7bc10388ccdd ACPI / resources: free memory on error in add_region_before() 0f1b414d1907 ACPI / PNP: Avoid conflicting resource reservations b9a5e5e18fbf ACPI / init: Fix the ordering of acpi_reserve_resources()
(commit b9a5e5e18fbf introduced regressions some of which, but not
all, were addressed by commit 0f1b414d1907 and commit 7bc10388ccdd
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.
The story is as follows. First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes. Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.
The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e18fbf).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d1907.
That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook. That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d1907 wouldn't be
necessary any more.
For this reason, the changes made by commit 0f1b414d1907 are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e18fbf that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.
Commit b9a5e5e18fbf "ACPI / init: Fix the ordering of
acpi_reserve_resources()" overlooked the fact that the memory
and/or I/O regions reserved by acpi_reserve_resources() may
conflict with those reserved by the PNP "system" driver.
If that conflict actually takes place, it causes the reservations
made by the "system" driver to fail while before commit b9a5e5e18fbf
all reservations made by it and by acpi_reserve_resources() would be
successful. In turn, that allows the resources that haven't been
reserved by the "system" driver to be used by others (e.g. PCI) which
sometimes leads to functional problems (up to and including boot
failures).
To fix that issue, introduce a common resource reservation routine,
acpi_reserve_region(), to be used by both acpi_reserve_resources()
and the "system" driver, that will track all resources reserved by
it and avoid making conflicting requests.
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit
architectures, and bails out if it fails. This causes a problem on
some platforms since the 64bit DMA isn't always guaranteed. We should
fall back to the default 32bit DMA when 64bit DMA fails.
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Fixes: ff2aeb1eb64c8a4770a6 ("libata: convert to chained sg") Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
Revert the main part of commit: af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests")
That commit introduced reading the pci device's msi message data to see
if a pirq was previously configured for the device's msi/msix, and re-use
that pirq. At the time, that was the correct behavior. However, a
later change to Qemu caused it to call into the Xen hypervisor to unmap
all pirqs for a pci device, when the pci device disables its MSI/MSIX
vectors; specifically the Qemu commit: c976437c7dba9c7444fb41df45468968aaa326ad
("qemu-xen: free all the pirqs for msi/msix when driver unload")
Once Qemu added this pirq unmapping, it was no longer correct for the
kernel to re-use the pirq number cached in the pci device msi message
data. All Qemu releases since 2.1.0 contain the patch that unmaps the
pirqs when the pci device disables its MSI/MSIX vectors.
This bug is causing failures to initialize multiple NVMe controllers
under Xen, because the NVMe driver sets up a single MSIX vector for
each controller (concurrently), and then after using that to talk to
the controller for some configuration data, it disables the single MSIX
vector and re-configures all the MSIX vectors it needs. So the MSIX
setup code tries to re-use the cached pirq from the first vector
for each controller, but the hypervisor has already given away that
pirq to another controller, and its initialization fails.
This is discussed in more detail at:
https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html
Fixes: af42b8d12f8a ("xen: fix MSI setup and teardown for PV on HVM guests") Signed-off-by: Dan Streetman <dan.streetman@canonical.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: cf7776dc05b8 ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection") Cc: Hansjoerg Lipp <hjlipp@web.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
While hunting for clues to a use-after-free, Oleg spotted that
perf_event_init_context() can loose an error value with the result
that fork() can succeed even though we did not fully inherit the perf
event context.
Spotted-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: oleg@redhat.com Fixes: 889ff0150661 ("perf/core: Split context's event group list into pinned and non-pinned lists") Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
When tc actions are loaded as a module and no actions have been installed,
flushing them would result in actions removed from the memory, but modules
reference count not being decremented, so that the modules would not be
unloaded.
Following is example with GACT action:
% sudo modprobe act_gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions ls action gact
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 1
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 2
% sudo rmmod act_gact
rmmod: ERROR: Module act_gact is in use
....
After the fix:
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions add action pass index 1
% sudo tc actions add action pass index 2
% sudo tc actions add action pass index 3
% lsmod
Module Size Used by
act_gact 16384 3
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
% sudo rmmod act_gact
% lsmod
Module Size Used by
%
Fixes: f97017cdefef ("net-sched: Fix actions flushing") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610d6 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <egarver@redhat.com> Cc: Hannes Sowa <hsowa@redhat.com> Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
It is now very clear that silly TCP listeners might play with
enabling/disabling timestamping while new children are added
to their accept queue.
Meaning net_enable_timestamp() can be called from BH context
while current state of the static key is not enabled.
Lets play safe and allow all contexts.
The work queue is scheduled only under the problematic cases,
which are the static key enable/disable transition, to not slow down
critical paths.
This extends and improves what we did in commit 5fa8bbda38c6 ("net: use
a work queue to defer net_disable_timestamp() work")
Fixes: b90e5794c5bd ("net: dont call jump_label_dec from irq context") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Add two helpers to make it easier to treat the refcount as boolean.
[js] do not involve WARN_ON_ONCE as it causes build failures
Suggested-by: Jason Baron <jasonbaron0@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[wt: only backported for use in next fix ;
s/static_key_count(key)/atomic_read(&key->enabled)/]
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a8212 ("USB: iowarrior: fix oops with malicious USB descriptors") Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
There are several trace include files that define TRACE_INCLUDE_FILE.
Include several of them in the same .c file (as I currently have in
some code I am working on), and the compile will blow up with a
"warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls"
Every other include file in include/trace/events/ avoids that issue
by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h
should have one, too.
Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com Fixes: b8007ef74222 ("tracing: Separate raw syscall from syscall tracer") Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
One of the last remaining failures in kernelci.org is for a gcc bug:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: error: insn does not satisfy its constraints:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: internal compiler error: in extract_constrain_insn, at recog.c:2190
This is apparently broken in gcc-6 but fixed in gcc-7, and I cannot
reproduce the problem here. However, it is clear that ip27_defconfig
does not actually need this driver as the platform has only PCI-X but
not PCIe, and the qlge adapter in turn is PCIe-only.
The driver was originally enabled in 2010 along with lots of other
drivers.
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 2d380889215f ("USB: serial: digi_acceleport: fix OOB data sanity
check") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Commit df2cb6daa4 ("block: Avoid deadlocks with bio allocation by
stacking drivers") created a workqueue for every bio set and code
in bio_alloc_bioset() that tries to resolve some low-memory deadlocks
by redirecting bios queued on current->bio_list to the workqueue if the
system is low on memory. However other deadlocks (see below **) may
happen, without any low memory condition, because generic_make_request
is queuing bios to current->bio_list (rather than submitting them).
** the related dm-snapshot deadlock is detailed here:
https://www.redhat.com/archives/dm-devel/2016-July/msg00065.html
Fix this deadlock by redirecting any bios on current->bio_list to the
bio_set's rescue workqueue on every schedule() call. Consequently,
when the process blocks on a mutex, the bios queued on
current->bio_list are dispatched to independent workqueus and they can
complete without waiting for the mutex to be available.
The structure blk_plug contains an entry cb_list and this list can contain
arbitrary callback functions that are called when the process blocks.
To implement this fix DM (ab)uses the onstack plug's cb_list interface
to get its flush_current_bio_list() called at schedule() time.
This fixes the snapshot deadlock - if the map method blocks,
flush_current_bio_list() will be called and it redirects bios waiting
on current->bio_list to appropriate workqueues.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1267650
Depends-on: df2cb6daa4 ("block: Avoid deadlocks with bio allocation by stacking drivers") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
It is not sufficient to just check that the lock pids match when
granting a callback, we also need to ensure that we're granting
the callback on the right file.
When calling set_mode from sys/fs, the call flow locks the sys/fs lock
first and then tries to lock rtnl_lock (when calling ipoib_set_mod).
On the other hand, the rmmod call flow takes the rtnl_lock first
(when calling unregister_netdev) and then tries to take the sys/fs
lock. Deadlock a->b, b->a.
The problem starts when ipoib_set_mod frees it's rtnl_lck and tries
to get it after that.
For devices with multiple input queues, tiqdio_call_inq_handlers()
iterates over all input queues and clears the device's DSCI
during each iteration. If the DSCI is re-armed during one
of the later iterations, we therefore do not scan the previous
queues again.
The re-arming also raises a new adapter interrupt. But its
handler does not trigger a rescan for the device, as the DSCI
has already been erroneously cleared.
This can result in queue stalls on devices with multiple
input queues.
Fix it by clearing the DSCI just once, prior to scanning the queues.
As the code is moved in front of the loop, we also need to access
the DSCI directly (ie irq->dsci) instead of going via each queue's
parent pointer to the same irq. This is not a functional change,
and a follow-up patch will clean up the other users.
In practice, this bug only affects CQ-enabled HiperSockets devices,
ie. devices with sysfs-attribute "hsuid" set. Setting a hsuid is
needed for AF_IUCV socket applications that use HiperSockets
communication.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Bitmap and attrlen follow immediately after the op reply header. This
was an oversight from commit bf118a342f.
Consequences of this are just minor efficiency (extra calls to
xdr_shrink_bufhead).
Fixes: bf118a342f10 "NFSv4: include bitmap in nfsv4 get acl data" Reviewed-by: Kinglong Mee <kinglongmee@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The RDMA core uses ib_pack() to convert from unpacked CPU structs
to on-the-wire bitpacked structs.
This process requires that 1 bit fields are declared as u8 in the
unpacked struct, otherwise the packing process does not read the
value properly and the packed result is wired to 0. Several
places wrongly used int.
Crucially this means the kernel has never, set reversible
correctly in the path record request. It has always asked for
irreversible paths even if the ULP requests otherwise.
When the kernel is used with a SM that supports this feature, it
completely breaks communication management if reversible paths are
not properly requested.
The only reason this ever worked is because opensm ignores the
reversible bit.
fuse_file_put() was missing the "force" flag for the RELEASE request when
sending synchronously (fuseblk).
If this flag is not set, then a sync request may be interrupted before it
is dequeued by the userspace filesystem. In this case the OPEN won't be
balanced with a RELEASE.
[js] force is a variable, not a bit
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 5a18ec176c93 ("fuse: fix hang of single threaded fuseblk filesystem") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
This patch fixes the OTP register definitions for the AR934x and AR9550
WMAC SoC.
Previously, the ath9k driver was unable to initialize the integrated
WMAC on an Aerohive AP121:
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004
| ath: phy0: Unable to initialize hardware; initialization status: -5
| ath9k ar934x_wmac: failed to initialize device
| ath9k: probe of ar934x_wmac failed with error -5
It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA
definitions contain a typo.
Cc: Gabor Juhos <juhosg@openwrt.org> Fixes: add295a4afbdf5852d0 "ath9k: use correct OTP register offsets for AR9550" Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb835223752 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family) Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: David Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
is_jump_ins() checks for plain jump ("j") instructions since commit e7438c4b893e ("MIPS: Fix sibling call handling in get_frame_info") but
that commit didn't make the same change to the microMIPS code, leaving
it inconsistent with the MIPS32/MIPS64 code. Handle the microMIPS
encoding of the jump instruction too such that it behaves consistently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: e7438c4b893e ("MIPS: Fix sibling call handling in get_frame_info") Cc: Tony Wu <tung7970@gmail.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14533/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
get_frame_info() calculates the offset of the return address within a
stack frame simply by dividing a the bottom 16 bits of the instruction,
treated as a signed integer, by the size of a long. Whilst this works
for MIPS32 & MIPS64 ISAs where the sw or sd instructions are used, it's
incorrect for microMIPS where encodings differ. The result is that we
typically completely fail to unwind the stack on microMIPS.
Fix this by adjusting is_ra_save_ins() to calculate the return address
offset, and take into account the various different encodings there in
the same place as we consider whether an instruction is storing the
ra/$31 register.
With this we are now able to unwind the stack for kernels targetting the
microMIPS ISA, for example we can produce:
is_jump_ins() checks 16b instruction fields without verifying that the
instruction is indeed 16b, as is done by is_ra_save_ins() &
is_sp_move_ins(). Add the appropriate check.
get_frame_info() is meant to iterate over up to the first 128
instructions within a function, but for microMIPS kernels it will not
reach that many instructions unless the function is 512 bytes long since
we calculate the maximum number of instructions to check by dividing the
function length by the 4 byte size of a union mips_instruction. In
microMIPS kernels this won't do since instructions are variable length.
Fix this by instead checking whether the pointer to the current
instruction has reached the end of the function, and use max_insns as a
simple constant to check the number of iterations against.
During stack unwinding we call a number of functions to determine what
type of instruction we're looking at. The union mips_instruction pointer
provided to them may be pointing at a 2 byte, but not 4 byte, aligned
address & we thus cannot directly access the 4 byte wide members of the
union mips_instruction. To avoid this is_ra_save_ins() copies the
required half-words of the microMIPS instruction to a correctly aligned
union mips_instruction on the stack, which it can then access safely.
The is_jump_ins() & is_sp_move_ins() functions do not correctly perform
this temporary copy, and instead attempt to directly dereference 4 byte
fields which may be misaligned and lead to an address exception.
Fix this by copying the instruction halfwords to a temporary union
mips_instruction in get_frame_info() such that we can provide a 4 byte
aligned union mips_instruction to the is_*_ins() functions and they do
not need to deal with misalignment themselves.
get_frame_info() can be called in microMIPS kernels with the ISA bit
already clear. For example this happens when unwind_stack_by_address()
is called because we begin with a PC that has the ISA bit set & subtract
the (odd) offset from the preceding symbol (which does not have the ISA
bit set). Since get_frame_info() unconditionally subtracts 1 from the PC
in microMIPS kernels it incorrectly misaligns the address it then
attempts to access code at, leading to an address error exception.
Fix this by using msk_isa16_mode() to clear the ISA bit, which allows
get_frame_info() to function regardless of whether it is provided with a
PC that has the ISA bit set or not.
If copy_from_user is called with a large buffer (>= 128 bytes) and the
userspace buffer refers partially to unreadable memory, then it is
possible for Octeon's copy_from_user to report the wrong number of bytes
have been copied. In the case where the buffer size is an exact multiple
of 128 and the fault occurs in the last 64 bytes, copy_from_user will
report that all the bytes were copied successfully but leave some
garbage in the destination buffer.
The bug is in the main __copy_user_common loop in octeon-memcpy.S where
in the middle of the loop, src and dst are incremented by 128 bytes. The
l_exc_copy fault handler is used after this but that assumes that
"src < THREAD_BUADDR($28)". This is not the case if src has already been
incremented.
Fix by adding an extra fault handler which rewinds the src and dst
pointers 128 bytes before falling though to l_exc_copy.
Thanks to the pwritev test from the strace test suite for originally
highlighting this bug!
Fixes: 5b3b16880f40 ("MIPS: Add Cavium OCTEON processor support ...") Signed-off-by: James Cowgill <James.Cowgill@imgtec.com> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14978/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
META_COLLECTOR int_vlan_tag() assumes that if the accel tag (vlan_tci)
is zero, then no vlan accel tag is present.
This is incorrect for zero VID vlan accel packets, making the following
match fail:
tc filter add ... basic match 'meta(vlan mask 0xfff eq 0)' ...
Apparently 'int_vlan_tag' was implemented prior VLAN_TAG_PRESENT was
introduced in 05423b2 "vlan: allow null VLAN ID to be used"
(and at time introduced, the 'vlan_tx_tag_get' call in em_meta was not
adapted).
Fix, testing skb_vlan_tag_present instead of testing skb_vlan_tag_get's
value.
Fixes: 05423b2413 ("vlan: allow null VLAN ID to be used") Fixes: 1a31f2042e ("netsched: Allow meta match on vlan tag on receive") Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
We currently count the size of LL_MAX_HEADER and struct iphdr
twice for vti4 devices, this leads to a wrong device mtu.
The size of LL_MAX_HEADER and struct iphdr is already counted in
ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init().
Fixes: b9959fd3 ("vti: switch to new ip tunnel code") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
Where the else path of the condition, that is, non-compression
path, calls memcpy() with a pointer to struct ipv6hdr *hdr as
source, thus two levels of indirection. This cannot be correct,
and likely only one level of pointer was intended as source
buffer for memcpy() here.
Fixes: 44331fe2aa0d ("IEEE802.15.4: 6LoWPAN basic support") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: Werner Almesberger <werner@almesberger.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
The goldfish platform code registers the platform device unconditionally
which causes havoc in several ways if the goldfish_pdev_bus driver is
enabled:
- Access to the hardcoded physical memory region, which is either not
available or contains stuff which is completely unrelated.
- Prevents that the interrupt of the serial port can be requested
- In case of a spurious interrupt it goes into a infinite loop in the
interrupt handler of the pdev_bus driver (which needs to be fixed
seperately).
Add a 'goldfish' command line option to make the registration opt-in when
the platform is compiled in.
I'm seriously grumpy about this engineering trainwreck, which has seven
SOBs from Intel developers for 50 lines of code. And none of them figured
out that this is broken. Impressive fail!
Fixes: ddd70cf93d78 ("goldfish: platform device for x86") Reported-by: Gabriel C <nix.or.die@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a452 ("USB: ark3116: Setup some basic infrastructure for new ark3116 driver.") Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware and add close and release functions.") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7a6ee2b02751 ("USB: opticon: switch to generic read implementation") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d8593 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc> Fixes: 72fda3ca6fc1 ("USB: serial: ftd_sio: implement sysrq handling on
break") Fixes: 166ceb690750 ("USB: ftdi_sio: clean up line-status handling") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Since commit 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6ba ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com> Fixes: 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY flag") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Commit 34b88a68f26a ("net: Fix use after free in the recvmmsg exit path"),
changed the exit path of recvmmsg to always return the datagrams
variable and modified the error paths to set the variable to the error
code returned by recvmsg if necessary.
However in the case sock_error returned an error, the error code was
then ignored, and recvmmsg returned 0.
Change the error path of recvmmsg to correctly return the error code
of sock_error.
The bug was triggered by using recvmmsg on a CAN interface which was
not up. Linux 4.6 and later return 0 in this case while earlier
releases returned -ENETDOWN.
Fixes: 34b88a68f26a ("net: Fix use after free in the recvmmsg exit path") Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
projects / thirdparty / kernel / stable.git / log
