w100fb_probe() did not reset the global state to its initial state. This
can result in invocation of iounmap() even when there was not the
appropriate successful call of ioremap(). For instance, this may be the
case if first probe fails after two successful ioremap() while second
probe fails when first ioremap() fails. The similar issue is with
w100fb_remove(). The patch fixes both bugs.
Found by Linux Driver Verification project (linuxtesting.org).
Coverity complains of a possible buffer overflow. However,
given the 'static' scope of nvidia_setup_i2c_bus() it looks
like that can't happen after examiniing the call sites.
CID 19036 (#1 of 1): Copy into fixed size buffer (STRING_OVERFLOW)
1. fixed_size_dest: You might overrun the 48-character fixed-size string
chan->adapter.name by copying name without checking the length.
2. parameter_as_source: Note: This defect has an elevated risk because the
source argument is a parameter of the current function.
89 strcpy(chan->adapter.name, name);
Fix this warning by using strscpy() which will silence the warning and
prevent any future buffer overflows should the names used to identify the
channel become much longer.
When the consumer works, it should enable the smi-larb's power which
also need enable the smi-common's power firstly.
Thus, First of all, use the device link connect the consumer and the
smi-larbs. then add device link between the smi-larb and smi-common.
This patch adds device_link between the consumer and the larbs.
When device_link_add, I add the flag DL_FLAG_STATELESS to avoid calling
pm_runtime_xx to keep the original status of clocks. It can avoid two
issues:
1) Display HW show fastlogo abnormally reported in [1]. At the beggining,
all the clocks are enabled before entering kernel, but the clocks for
display HW(always in larb0) will be gated after clk_enable and clk_disable
called from device_link_add(->pm_runtime_resume) and rpm_idle. The clock
operation happened before display driver probe. At that time, the display
HW will be abnormal.
2) A deadlock issue reported in [2]. Use DL_FLAG_STATELESS to skip
pm_runtime_xx to avoid the deadlock.
Corresponding, DL_FLAG_AUTOREMOVE_CONSUMER can't be added, then
device_link_removed should be added explicitly.
Meanwhile, Currently we don't have a device connect with 2 larbs at the
same time. Disallow this case, print the error log.
The platform device is created at:
of_platform_default_populate_init: arch_initcall_sync
->of_platform_populate
->of_platform_device_create_pdata
When entering our probe, all the devices should be already created.
if it is null, means NODEV. Currently we don't get the fail case.
It's a minor fix, no need add fixes tags.
Signed-off-by: Yong Wu <yong.wu@mediatek.com> Acked-by: Joerg Roedel <jroedel@suse.de> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the iommu master device enters of_iommu_xlate, the ops may be
NULL(iommu dev is defered), then it will initialize the fwspec here:
[<c0c9c5bc>] (dev_iommu_fwspec_set) from [<c06bda80>]
(iommu_fwspec_init+0xbc/0xd4)
[<c06bd9c4>] (iommu_fwspec_init) from [<c06c0db4>]
(of_iommu_xlate+0x7c/0x12c)
[<c06c0d38>] (of_iommu_xlate) from [<c06c10e8>]
(of_iommu_configure+0x144/0x1e8)
BUT the mtk_iommu_v1.c only supports arm32, the probing flow still is a bit
weird. We always expect create the fwspec internally. otherwise it will
enter here and return fail.
static int mtk_iommu_create_mapping(struct device *dev,
struct of_phandle_args *args)
{
...
if (!fwspec) {
....
} else if (dev_iommu_fwspec_get(dev)->ops != &mtk_iommu_ops) {
>>>>>>>>>>Enter here. return fail.<<<<<<<<<<<<
return -EINVAL;
}
...
}
Thus, Free the existed fwspec if the master device already has fwspec.
This issue is reported at:
https://lore.kernel.org/linux-mediatek/trinity-7d9ebdc9-4849-4d93-bfb5-429dcb4ee449-1626253158870@3c-app-gmx-bs01/
Reported-by: Frank Wunderlich <frank-w@public-files.de> Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623 Signed-off-by: Yong Wu <yong.wu@mediatek.com> Acked-by: Joerg Roedel <jroedel@suse.de> Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the application queues an NV12M jpeg as output buffer, but then
queues a single planar capture buffer, the kernel will crash with
"Unable to handle kernel NULL pointer dereference" in mxc_jpeg_addrs,
prevent this by finishing the job with error.
Codecs with the same part id, manufacturer id and part id, but different
sdw version should be treated as different codecs. For example, rt711 and
rt711-sdca are different. So, we should match sdw version as well.
Reported-by: Reddy Muralidhar <muralidhar.reddy@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220120232157.199919-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a plug event is detect report the full state of all status
bits, don't assume that there will have been a previous unplug
event to clear all the bits. Report the state of both HEADPHONE
and MICROPHONE bits according to detected type, and clear all the
button status bits. The current button status is already checked
and reported at the end of the function.
During a system suspend the jack could be unplugged and plugged,
possibly changing the jack type. On resume the interrupt status will
indicate a plug event - there will not be an unplug event to clear
the bits.
The ISC supports a full broad range of frame sizes.
Until now, the subdevice was queried for possible frame sizes and these
were reported to the user space.
However, the ISC should not care about which frame sizes the subdev
supports, as long as this frame size is supported.
Thus, report a continuous range from smallest frame size up to the max
resolution.
This fixes several issues found with 'v4l2-compliance -s':
1) read()/write() is supported, but not reported in the capabilities
2) S_STD(G_STD()) failed: setting the same standard should just return 0.
3) G_PARM failed to set readbuffers.
4) different field values in the format vs. what v4l2_buffer reported.
5) zero the sequence number when starting streaming.
6) drop VB_USERPTR: makes no sense with dma_contig streaming.
Move some code out of zr36057_init() and create new functions for handling
zr->video_dev. This permit to ease code reading and fix a zr->video_dev
memory leak.
When session gets reconnected during mount then read size in super block fs context
gets set to zero and after negotiate, rsize is not modified which results in
incorrect read with requested bytes as zero. Fixes intermittent failure
of xfstest generic/240
Note that stable requires a different version of this patch which will be
sent to the stable mailing list.
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com> Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In lz4_decompress_pages(), if size of decompressed data is not equal to
expected one, we should print the size rather than size of target buffer
for decompressed data, fix it.
The submit helper will always run bio_endio() on the bio if it fails to
submit, so cleaning up the bio just leads to a variety of use-after-free
and NULL pointer dereference bugs because we race with the endio
function that is cleaning up the bio. Instead just return BLK_STS_OK as
the repair function has to continue to process the rest of the pages,
and the endio for the repair bio will do the appropriate cleanup for the
page that it was given.
Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I hit some weird panics while fixing up the error handling from
btrfs_lookup_bio_sums(). Turns out the compression path will complete
the bio we use if we set up any of the compression bios and then return
an error, and then btrfs_submit_data_bio() will also call bio_endio() on
the bio.
Fix this by making btrfs_submit_compressed_read() responsible for
calling bio_endio() on the bio if there are any errors. Currently it
was only doing it if we created the compression bios, otherwise it was
depending on btrfs_submit_data_bio() to do the right thing. This
creates the above problem, so fix up btrfs_submit_compressed_read() to
always call bio_endio() in case of an error, and then simply return from
btrfs_submit_data_bio() if we had to call
btrfs_submit_compressed_read().
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently any error we get while trying to lookup csums during reads
shows up as a missing csum, and then on the read completion side we
print an error saying there was a csum mismatch and we increase the
device corruption count.
However we could have gotten an EIO from the lookup. We could also be
inside of a memory constrained container and gotten a ENOMEM while
trying to do the read. In either case we don't want to make this look
like a file system corruption problem, we want to make it look like the
actual error it is. Capture any negative value, convert it to the
appropriate blk_status_t, free the csum array if we have one and bail.
Note: a possible improvement would be to make the relocation code look
up the owning inode and see if it's marked as NODATASUM and set
EXTENT_NODATASUM there, that way if there's corruption and there isn't a
checksum when we want it we can fail here rather than later.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can either fail to find a csum entry at all and return -ENOENT, or we
can find a range that is close, but return -EFBIG. In essence these
both mean the same thing when we are doing a lookup for a csum in an
existing range, we didn't find a csum. We want to treat both of these
errors the same way, complain loudly that there wasn't a csum. This
currently happens anyway because we do
count = search_csum_tree();
if (count <= 0) {
// reloc and error handling
}
However it forces us to incorrectly treat EIO or ENOMEM errors as on
disk corruption. Fix this by returning 0 if we get either -ENOENT or
-EFBIG from btrfs_lookup_csum() so we can do proper error handling.
Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Identifying and removing the stale device from the fs_uuids list is done
by btrfs_free_stale_devices(). btrfs_free_stale_devices() in turn
depends on device_path_matched() to check if the device appears in more
than one btrfs_device structure.
The matching of the device happens by its path, the device path. However,
when device mapper is in use, the dm device paths are nothing but a link
to the actual block device, which leads to the device_path_matched()
failing to match.
Fix this by matching the dev_t as provided by lookup_bdev() instead of
plain string compare of the device paths.
Reported-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[un]pin_user_pages_remote is dirtying pages without properly warning
the file system in advance. A related race was noted by Jan Kara in
2018[1]; however, more recently instead of it being a very hard-to-hit
race, it could be reliably triggered by process_vm_writev(2) which was
discovered by Syzbot[2].
This is technically a bug in mm/gup.c, but arguably ext4 is fragile in
that if some other kernel subsystem dirty pages without properly
notifying the file system using page_mkwrite(), ext4 will BUG, while
other file systems will not BUG (although data will still be lost).
So instead of crashing with a BUG, issue a warning (since there may be
potential data loss) and just mark the page as clean to avoid
unprivileged denial of service attacks until the problem can be
properly fixed. More discussion and background can be found in the
thread starting at [2].
TASK_RTLOCK_WAIT currently isn't part of TASK_REPORT, thus a task blocking
on an rtlock will appear as having a task state == 0, IOW TASK_RUNNING.
The actual state is saved in p->saved_state, but reading it after reading
p->__state has a few issues:
o that could still be TASK_RUNNING in the case of e.g. rt_spin_lock
o ttwu_state_match() might have changed that to TASK_RUNNING
As pointed out by Eric, adding TASK_RTLOCK_WAIT to TASK_REPORT implies
exposing a new state to userspace tools which way not know what to do with
them. The only information that needs to be conveyed here is that a task is
waiting on an rt_mutex, which matches TASK_UNINTERRUPTIBLE - there's no
need for a new state.
In case of flex_bg feature (which is by default enabled), extents for
any given inode might span across blocks from two different block group.
ext4_mb_mark_bb() only reads the buffer_head of block bitmap once for the
starting block group, but it fails to read it again when the extent length
boundary overflows to another block group. Then in this below loop it
accesses memory beyond the block group bitmap buffer_head and results
into a data abort.
for (i = 0; i < clen; i++)
if (!mb_test_bit(blkoff + i, bitmap_bh->b_data) == !state)
already++;
This patch adds this functionality for checking block group boundary in
ext4_mb_mark_bb() and update the buffer_head(bitmap_bh) for every different
block group.
w/o this patch, I was easily able to hit a data access abort using Power platform.
When dumping lock_classes information via /proc/lockdep, we can't take
the lockdep lock as the lock hold time is indeterminate. Iterating
over all_lock_classes without holding lock can be dangerous as there
is a slight chance that it may branch off to other lists leading to
infinite loop or even access invalid memory if changes are made to
all_lock_classes list in parallel.
To avoid this problem, iteration of lock classes is now done directly
on the lock_classes array itself. The lock_classes_in_use bitmap is
checked to see if the lock class is being used. To avoid iterating
the full array all the times, a new max_lock_class_idx value is added
to track the maximum lock_class index that is currently being used.
We can theoretically take the lockdep lock for iterating all_lock_classes
when other lockdep files (lockdep_stats and lock_stat) are accessed as
the lock hold time will be shorter for them. For consistency, they are
also modified to iterate the lock_classes array directly.
Arnd reports that on 32-bit architectures, the fallbacks for
atomic64_read_acquire() and atomic64_set_release() are broken as they
use smp_load_acquire() and smp_store_release() respectively, which do
not work on types larger than the native word size.
Since those contain compiletime_assert_atomic_type(), any attempt to use
those fallbacks will result in a build-time error. e.g. with the
following added to arch/arm/kernel/setup.c:
| In file included from <command-line>:
| In function 'arch_atomic64_set_release',
| inlined from 'test_atomic64' at ./include/linux/atomic/atomic-instrumented.h:669:2:
| ././include/linux/compiler_types.h:346:38: error: call to '__compiletime_assert_9' declared with attribute error: Need native word sized stores/loads for atomicity.
| 346 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| | ^
| ././include/linux/compiler_types.h:327:4: note: in definition of macro '__compiletime_assert'
| 327 | prefix ## suffix(); \
| | ^~~~~~
| ././include/linux/compiler_types.h:346:2: note: in expansion of macro '_compiletime_assert'
| 346 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| | ^~~~~~~~~~~~~~~~~~~
| ././include/linux/compiler_types.h:349:2: note: in expansion of macro 'compiletime_assert'
| 349 | compiletime_assert(__native_word(t), \
| | ^~~~~~~~~~~~~~~~~~
| ./include/asm-generic/barrier.h:133:2: note: in expansion of macro 'compiletime_assert_atomic_type'
| 133 | compiletime_assert_atomic_type(*p); \
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| ./include/asm-generic/barrier.h:164:55: note: in expansion of macro '__smp_store_release'
| 164 | #define smp_store_release(p, v) do { kcsan_release(); __smp_store_release(p, v); } while (0)
| | ^~~~~~~~~~~~~~~~~~~
| ./include/linux/atomic/atomic-arch-fallback.h:1270:2: note: in expansion of macro 'smp_store_release'
| 1270 | smp_store_release(&(v)->counter, i);
| | ^~~~~~~~~~~~~~~~~
| make[2]: *** [scripts/Makefile.build:288: arch/arm/kernel/setup.o] Error 1
| make[1]: *** [scripts/Makefile.build:550: arch/arm/kernel] Error 2
| make: *** [Makefile:1831: arch/arm] Error 2
Fix this by only using smp_load_acquire() and smp_store_release() for
native atomic types, and otherwise falling back to the regular barriers
necessary for acquire/release semantics, as we do in the more generic
acquire and release fallbacks.
Since the fallback templates are used to generate the atomic64_*() and
atomic_*() operations, the __native_word() check is added to both. For
the atomic_*() operations, which are always 32-bit, the __native_word()
check is redundant but not harmful, as it is always true.
For the example above this works as expected on 32-bit, e.g. for arm
multi_v7_defconfig:
The data transfer routines must poll the status register to
determine when more data can be shifted in or out. If the hardware
gets into a bad state, these polling loops may never exit. Prevent
this by returning an error if a timeout is exceeded.
Put NVMe/TCP sockets in their own class to avoid some lockdep warnings.
Sockets created by nvme-tcp are not exposed to user-space, and will not
trigger certain code paths that the general socket API exposes.
Lockdep complains about a circular dependency between the socket and
filesystem locks, because setsockopt can trigger a page fault with a
socket lock held, but nvme-tcp sends requests on the socket while file
system locks are held.
======================================================
WARNING: possible circular locking dependency detected
5.15.0-rc3 #1 Not tainted
------------------------------------------------------
fio/1496 is trying to acquire lock:
(sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_sendpage+0x23/0x80
but task is already holding lock:
(&xfs_dir_ilock_class/5){+.+.}-{3:3}, at: xfs_ilock+0xcf/0x290 [xfs]
Currently, the parisc kernel does not fully support non-access TLB
fault handling for probe instructions. In the fast path, we set the
target register to zero if it is not a shadowed register. The slow
path is not implemented, so we call do_page_fault. The architecture
indicates that non-access faults should not cause a page fault from
disk.
This change adds to code to provide non-access fault support for
probe instructions. It also modifies the handling of faults on
userspace so that if the address lies in a valid VMA and the access
type matches that for the VMA, the probe target register is set to
one. Otherwise, the target register is set to zero.
This was done to make probe instructions more useful for userspace.
Probe instructions are not very useful if they set the target register
to zero whenever a page is not present in memory. Nominally, the
purpose of the probe instruction is determine whether read or write
access to a given address is allowed.
This fixes a problem in function pointer comparison noticed in the
glibc testsuite (stdio-common/tst-vfprintf-user-type). The same
problem is likely in glibc (_dl_lookup_address).
V2 adds flush and lpa instruction support to handle_nadtlb_fault.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a page is not present, we get non-access data TLB faults from
the fdc and fic instructions in flush_user_dcache_range_asm and
flush_user_icache_range_asm. When these occur, the cache line is
not invalidated and potentially we get memory corruption. The
problem was hidden by the nullification of the flush instructions.
These faults also affect performance. With pa8800/pa8900 processors,
there will be 32 faults per 4 KB page since the cache line is 128
bytes. There will be more faults with earlier processors.
The problem is fixed by using flush_cache_pages(). It does the flush
using a tmp alias mapping.
The flush_cache_pages() call in flush_cache_range() flushed too
large a range.
V2: Remove unnecessary preempt_disable() and preempt_enable() calls.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function device_pm_check_callbacks() can be called under the spin
lock (in the reported case it happens from genpd_add_device() ->
dev_pm_domain_set(), when the genpd uses spinlocks rather than mutexes.
However this function uncoditionally uses spin_lock_irq() /
spin_unlock_irq(), thus not preserving the CPU flags. Use the
irqsave/irqrestore instead.
Platforms with large BERT table data can trigger soft lockup errors
while attempting to print the entire BERT table data to the console at
boot:
watchdog: BUG: soft lockup - CPU#160 stuck for 23s! [swapper/0:1]
Observed on Ampere Altra systems with a single BERT record of ~250KB.
The original bert driver appears to have assumed relatively small table
data. Since it is impractical to reassemble large table data from
interwoven console messages, and the table data is available in
/sys/firmware/acpi/tables/data/BERT
limit the size for tables printed to the console to 1024 (for no reason
other than it seemed like a good place to kick off the discussion, would
appreciate feedback from existing users in terms of what size would
maintain their current usage model).
Alternatively, we could make printing a CONFIG option, use the
bert_disable boot arg (or something similar), or use a debug log level.
However, all those solutions require extra steps or change the existing
behavior for small table data. Limiting the size preserves existing
behavior on existing platforms with small table data, and eliminates the
soft lockups for platforms with large table data, while still making it
available.
Signed-off-by: Darren Hart <darren@os.amperecomputing.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A crash [1] happened to be triggered in conjunction with commit 2d52c58b9c9b ("block, bfq: honor already-setup queue merges"). The
latter was then reverted by commit ebc69e897e17 ("Revert "block, bfq:
honor already-setup queue merges""). Yet, the reverted commit was not
the one introducing the bug. In fact, it actually triggered a UAF
introduced by a different commit, and now fixed by commit d29bd41428cf
("block, bfq: reset last_bfqq_created on group change").
So, there is no point in keeping commit 2d52c58b9c9b ("block, bfq:
honor already-setup queue merges") out. This commit restores it.
Buidling raid6test on Ubuntu 21.10 (ppc64le) with GNU Make 4.3 shows the
errors below:
$ cd lib/raid6/test/
$ make
<stdin>:1:1: error: stray ‘\’ in program
<stdin>:1:2: error: stray ‘#’ in program
<stdin>:1:11: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ \
before ‘<’ token
[...]
The errors come from the HAS_ALTIVEC test, which fails, and the POWER
optimized versions are not built. That’s also reason nobody noticed on the
other architectures.
GNU Make 4.3 does not remove the backslash anymore. From the 4.3 release
announcment:
> * WARNING: Backward-incompatibility!
> Number signs (#) appearing inside a macro reference or function invocation
> no longer introduce comments and should not be escaped with backslashes:
> thus a call such as:
> foo := $(shell echo '#')
> is legal. Previously the number sign needed to be escaped, for example:
> foo := $(shell echo '\#')
> Now this latter will resolve to "\#". If you want to write makefiles
> portable to both versions, assign the number sign to a variable:
> H := \#
> foo := $(shell echo '$H')
> This was claimed to be fixed in 3.81, but wasn't, for some reason.
> To detect this change search for 'nocomment' in the .FEATURES variable.
So, do the same as commit 9564a8cf422d ("Kbuild: fix # escaping in .cmd
files for future Make") and commit 929bef467771 ("bpf: Use $(pound) instead
of \# in Makefiles") and define and use a $(pound) variable.
Reference for the change in make:
https://git.savannah.gnu.org/cgit/make.git/commit/?id=c6966b323811c37acedff05b57
Cc: Matt Brown <matthew.brown.dev@gmail.com> Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prevent acpi_ns_walk_namespace() from crashing when called with
start_node equal to ACPI_ROOT_OBJECT if the Namespace has not been
instantiated yet and acpi_gbl_root_node is NULL.
For instance, this can happen if the kernel is run with "acpi=off"
in the command line.
KASAN reports a use-after-free report when doing normal scsi-mq test
[69832.239032] ==================================================================
[69832.241810] BUG: KASAN: use-after-free in bfq_dispatch_request+0x1045/0x44b0
[69832.243267] Read of size 8 at addr ffff88802622ba88 by task kworker/3:1H/155
[69832.244656]
[69832.245007] CPU: 3 PID: 155 Comm: kworker/3:1H Not tainted 5.10.0-10295-g576c6382529e #8
[69832.246626] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[69832.249069] Workqueue: kblockd blk_mq_run_work_fn
[69832.250022] Call Trace:
[69832.250541] dump_stack+0x9b/0xce
[69832.251232] ? bfq_dispatch_request+0x1045/0x44b0
[69832.252243] print_address_description.constprop.6+0x3e/0x60
[69832.253381] ? __cpuidle_text_end+0x5/0x5
[69832.254211] ? vprintk_func+0x6b/0x120
[69832.254994] ? bfq_dispatch_request+0x1045/0x44b0
[69832.255952] ? bfq_dispatch_request+0x1045/0x44b0
[69832.256914] kasan_report.cold.9+0x22/0x3a
[69832.257753] ? bfq_dispatch_request+0x1045/0x44b0
[69832.258755] check_memory_region+0x1c1/0x1e0
[69832.260248] bfq_dispatch_request+0x1045/0x44b0
[69832.261181] ? bfq_bfqq_expire+0x2440/0x2440
[69832.262032] ? blk_mq_delay_run_hw_queues+0xf9/0x170
[69832.263022] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.264011] ? blk_mq_sched_request_inserted+0x100/0x100
[69832.265101] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.266206] ? blk_mq_do_dispatch_ctx+0x570/0x570
[69832.267147] ? __switch_to+0x5f4/0xee0
[69832.267898] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.268946] __blk_mq_run_hw_queue+0xc0/0x270
[69832.269840] blk_mq_run_work_fn+0x51/0x60
[69832.278170] process_one_work+0x6d4/0xfe0
[69832.278984] worker_thread+0x91/0xc80
[69832.279726] ? __kthread_parkme+0xb0/0x110
[69832.280554] ? process_one_work+0xfe0/0xfe0
[69832.281414] kthread+0x32d/0x3f0
[69832.282082] ? kthread_park+0x170/0x170
[69832.282849] ret_from_fork+0x1f/0x30
[69832.283573]
[69832.283886] Allocated by task 7725:
[69832.284599] kasan_save_stack+0x19/0x40
[69832.285385] __kasan_kmalloc.constprop.2+0xc1/0xd0
[69832.286350] kmem_cache_alloc_node+0x13f/0x460
[69832.287237] bfq_get_queue+0x3d4/0x1140
[69832.287993] bfq_get_bfqq_handle_split+0x103/0x510
[69832.289015] bfq_init_rq+0x337/0x2d50
[69832.289749] bfq_insert_requests+0x304/0x4e10
[69832.290634] blk_mq_sched_insert_requests+0x13e/0x390
[69832.291629] blk_mq_flush_plug_list+0x4b4/0x760
[69832.292538] blk_flush_plug_list+0x2c5/0x480
[69832.293392] io_schedule_prepare+0xb2/0xd0
[69832.294209] io_schedule_timeout+0x13/0x80
[69832.295014] wait_for_common_io.constprop.1+0x13c/0x270
[69832.296137] submit_bio_wait+0x103/0x1a0
[69832.296932] blkdev_issue_discard+0xe6/0x160
[69832.297794] blk_ioctl_discard+0x219/0x290
[69832.298614] blkdev_common_ioctl+0x50a/0x1750
[69832.304715] blkdev_ioctl+0x470/0x600
[69832.305474] block_ioctl+0xde/0x120
[69832.306232] vfs_ioctl+0x6c/0xc0
[69832.306877] __se_sys_ioctl+0x90/0xa0
[69832.307629] do_syscall_64+0x2d/0x40
[69832.308362] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[69832.309382]
[69832.309701] Freed by task 155:
[69832.310328] kasan_save_stack+0x19/0x40
[69832.311121] kasan_set_track+0x1c/0x30
[69832.311868] kasan_set_free_info+0x1b/0x30
[69832.312699] __kasan_slab_free+0x111/0x160
[69832.313524] kmem_cache_free+0x94/0x460
[69832.314367] bfq_put_queue+0x582/0x940
[69832.315112] __bfq_bfqd_reset_in_service+0x166/0x1d0
[69832.317275] bfq_bfqq_expire+0xb27/0x2440
[69832.318084] bfq_dispatch_request+0x697/0x44b0
[69832.318991] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.319984] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.321087] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.322225] __blk_mq_run_hw_queue+0xc0/0x270
[69832.323114] blk_mq_run_work_fn+0x51/0x60
[69832.323942] process_one_work+0x6d4/0xfe0
[69832.324772] worker_thread+0x91/0xc80
[69832.325518] kthread+0x32d/0x3f0
[69832.326205] ret_from_fork+0x1f/0x30
[69832.326932]
[69832.338297] The buggy address belongs to the object at ffff88802622b968
[69832.338297] which belongs to the cache bfq_queue of size 512
[69832.340766] The buggy address is located 288 bytes inside of
[69832.340766] 512-byte region [ffff88802622b968, ffff88802622bb68)
[69832.343091] The buggy address belongs to the page:
[69832.344097] page:ffffea0000988a00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88802622a528 pfn:0x26228
[69832.346214] head:ffffea0000988a00 order:2 compound_mapcount:0 compound_pincount:0
[69832.347719] flags: 0x1fffff80010200(slab|head)
[69832.348625] raw: 001fffff80010200ffffea0000dbac08ffff888017a57650ffff8880179fe840
[69832.354972] raw: ffff88802622a528000000000012000800000001ffffffff0000000000000000
[69832.356547] page dumped because: kasan: bad access detected
[69832.357652]
[69832.357970] Memory state around the buggy address:
[69832.358926] ffff88802622b980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.360358] ffff88802622ba00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.361810] >ffff88802622ba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.363273] ^
[69832.363975] ffff88802622bb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
[69832.375960] ffff88802622bb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[69832.377405] ==================================================================
In bfq_dispatch_requestfunction, it may have function call:
bfq_dispatch_request
__bfq_dispatch_request
bfq_select_queue
bfq_bfqq_expire
__bfq_bfqd_reset_in_service
bfq_put_queue
kmem_cache_free
In this function call, in_serv_queue has beed expired and meet the
conditions to free. In the function bfq_dispatch_request, the address
of in_serv_queue pointing to has been released. For getting the value
of idle_timer_disabled, it will get flags value from the address which
in_serv_queue pointing to, then the problem of use-after-free happens;
Fix the problem by check in_serv_queue == bfqd->in_service_queue, to
get the value of idle_timer_disabled if in_serve_queue is equel to
bfqd->in_service_queue. If the space of in_serv_queue pointing has
been released, this judge will aviod use-after-free problem.
And if in_serv_queue may be expired or finished, the idle_timer_disabled
will be false which would not give effects to bfq_update_dispatch_stats.
: The AT_PHDR of ELF auxiliary vectors should point to the memory address
: of program header. But binfmt_elf.c calculates this address as follows:
:
: NEW_AUX_ENT(AT_PHDR, load_addr + exec->e_phoff);
:
: which is wrong since e_phoff is the file offset of program header and
: load_addr is the memory base address from PT_LOAD entry.
:
: The ld.so uses AT_PHDR as the memory address of program header. In normal
: case, since the e_phoff is usually 64 and in the first PT_LOAD region, it
: is the correct program header address.
:
: But if the address of program header isn't equal to the first PT_LOAD
: address + e_phoff (e.g. Put the program header in other non-consecutive
: PT_LOAD region), ld.so will try to read program header from wrong address
: then crash or use incorrect program header.
This is because exec->e_phoff
is the offset of PHDRs in the file and the address of PHDRs in the
memory may differ from it. This patch fixes the bug by calculating the
address of program headers from PT_LOADs directly.
pdc_enable_intr() serves as a primitive to qcom_pdc_gic_{en,dis}able,
and has a raw spinlock for mutual exclusion, which is uses with
interruptible primitives.
This means that this critical section can itself be interrupted.
Should the interrupt also be a PDC interrupt, and the endpoint driver
perform an irq_disable() on that interrupt, we end-up in a deadlock.
Fix this by using the irqsave/irqrestore variants of the locking
primitives.
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for outputting sysfs content and it's possible to overrun the
PAGE_SIZE buffer length.
Use a generic sysfs_emit function that knows the size of the
temporary buffer and ensures that no overrun is done for offset
attribute in
loop_attr_[offset|sizelimit|autoclear|partscan|dio]_show() callbacks.
These ioctls are equivalent to fcntl(fd, F_SETFD, flags), which SELinux
always allows too. Furthermore, a failed FIOCLEX could result in a file
descriptor being leaked to a process that should not have access to it.
As this patch removes access controls, a policy capability needs to be
enabled in policy to always allow these ioctls.
Based-on-patch-by: Demi Marie Obenour <demiobenour@gmail.com> Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
[PM: subject line tweak] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On ELF, (NOLOAD) sets the section type to SHT_NOBITS[1]. It is conceptually
inappropriate for .plt and .text.* sections which are always
SHT_PROGBITS.
In GNU ld, if PLT entries are needed, .plt will be SHT_PROGBITS anyway
and (NOLOAD) will be essentially ignored. In ld.lld, since
https://reviews.llvm.org/D118840 ("[ELF] Support (TYPE=<value>) to
customize the output section type"), ld.lld will report a `section type
mismatch` error. Just remove (NOLOAD) to fix the error.
[1] https://lld.llvm.org/ELF/linker_script.html As of today, "The
section should be marked as not loadable" on
https://sourceware.org/binutils/docs/ld/Output-Section-Type.html is
outdated for ELF.
The release function does not reset the per cpu variable when it is
called. That will prevent creation again as the variable will be
already from the previous creation.
security_sid_to_context() expects a pointer to an u32 as the address
where to store the length of the computed context.
Reported by sparse:
security/selinux/xfrm.c:359:39: warning: incorrect type in arg 4
(different signedness)
security/selinux/xfrm.c:359:39: expected unsigned int
[usertype] *scontext_len
security/selinux/xfrm.c:359:39: got int *
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
[PM: wrapped commit description] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The xts module needs ecb to be present as it's meant to work
on top of ecb. This patch adds a softdep so ecb can be included
automatically into the initramfs.
Use set_disk_ro to propagate the read-only state to the block layer
instead of checking for it in ->open and leaking a reference in case
of a read-only device.
Commit 111be8839817 ("block-throttle: avoid double charge") marks bio as
BIO_THROTTLED unconditionally if __blk_throtl_bio() is called on this bio,
then this bio won't be called into __blk_throtl_bio() any more. This way
is to avoid double charge in case of bio splitting. It is reasonable for
read/write throughput limit, but not reasonable for IOPS limit because
block layer provides io accounting against split bio.
Chunguang Xu has already observed this issue and fixed it in commit 4f1e9630afe6 ("blk-throtl: optimize IOPS throttle for large IO scenarios").
However, that patch only covers bio splitting in __blk_queue_split(), and
we have other kind of bio splitting, such as bio_split() &
submit_bio_noacct() and other ways.
This patch tries to fix the issue in one generic way by always charging
the bio for iops limit in blk_throtl_bio(). This way is reasonable:
re-submission & fast-cloned bio is charged if it is submitted to same
disk/queue, and BIO_THROTTLED will be cleared if bio->bi_bdev is changed.
This new approach can get much more smooth/stable iops limit compared with
commit 4f1e9630afe6 ("blk-throtl: optimize IOPS throttle for large IO
scenarios") since that commit can't throttle current split bios actually.
Also this way won't cause new double bio iops charge in
blk_throtl_dispatch_work_fn() in which blk_throtl_bio() won't be called
any more.
Reported-by: Ning Li <lining2020x@163.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Chunguang Xu <brookxu@tencent.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20220216044514.2903784-7-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
KCSAN reports data races between the rcu_segcblist_clear_flags() and
rcu_segcblist_set_flags() functions, though misreporting the latter
as a call to rcu_segcblist_is_enabled() from call_rcu(). This commit
converts the updates of this field to WRITE_ONCE(), relying on the
resulting unmarked reads to continue to detect buggy concurrent writes
to this field.
Reported-by: Zhouyi Zhou <zhouzhouyi@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Cc: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The npcm driver has a bunch of references to the irq_chip parent_device
field, but never sets it.
Fix it by fishing that reference from somewhere else, but it is
obvious that these debug statements were never used. Also remove
an unused field in a local data structure.
If we allow architectures to bring APs online in parallel, then we end
up requiring rcu_cpu_starting() to be reentrant. But currently, the
manipulation of rnp->ofl_seq is not thread-safe.
However, rnp->ofl_seq is also fairly much pointless anyway since both
rcu_cpu_starting() and rcu_report_dead() hold rcu_state.ofl_lock for
fairly much the whole time that rnp->ofl_seq is set to an odd number
to indicate that an operation is in progress.
So drop rnp->ofl_seq completely, and use only rcu_state.ofl_lock.
This has a couple of minor complexities: lockdep will complain when we
take rcu_state.ofl_lock, and currently accepts the 'excuse' of having
an odd value in rnp->ofl_seq. So switch it to an arch_spinlock_t to
avoid that false positive complaint. Since we're killing rnp->ofl_seq
of course that 'excuse' has to be changed too, so make it check for
arch_spin_is_locked(rcu_state.ofl_lock).
There's no arch_spin_lock_irqsave() so we have to manually save and
restore local interrupts around the locking.
At Paul's request based on Neeraj's analysis, make rcu_gp_init not just
wait but *exclude* any CPU online/offline activity, which was fairly
much true already by virtue of it holding rcu_state.ofl_lock.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since STRING_CST may not be NUL terminated, strncmp() was used for check
for equality. However, this may lead to mismatches for longer section
names where the start matches the tested-for string. Test for exact
equality by checking for the presences of NUL termination.
The kernel test rebot report this warning: Uninitialized variable: ret.
The code flow may return value of ret directly. This value is an
uninitialized variable, here is fix it.
Signed-off-by: Kai Ye <yekai13@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.
Increase delays appropriately, and retry should I2C errors be
reported.
The usual LSM hook "bail on fail" scheme doesn't work for cases where
a security module may return an error code indicating that it does not
recognize an input. In this particular case Smack sees a mount option
that it recognizes, and returns 0. A call to a BPF hook follows, which
returns -ENOPARAM, which confuses the caller because Smack has processed
its data.
The SELinux hook incorrectly returns 1 on success. There was a time
when this was correct, however the current expectation is that it
return 0 on success. This is repaired.
Reported-by: syzbot+d1e3b1d92d25abf97943@syzkaller.appspotmail.com Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: James Morris <jamorris@linux.microsoft.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jason Donenfeld reports that my commit 1c24a186398f ("fs: fd tables have
to be multiples of BITS_PER_LONG") doesn't work, and the reason is an
embarrassing brown-paper-bag bug.
Yes, we want to align the number of fds to BITS_PER_LONG, and yes, the
reason they might not be aligned is because the incoming 'max_fd'
argument might not be aligned.
But aligining the argument - while simple - will cause a "infinitely
big" maxfd (eg NR_OPEN_MAX) to just overflow to zero. Which most
definitely isn't what we want either.
The obvious fix was always just to do the alignment last, but I had
moved it earlier just to make the patch smaller and the code look
simpler. Duh. It certainly made _me_ look simple.
Fixes: 1c24a186398f ("fs: fd tables have to be multiples of BITS_PER_LONG") Reported-and-tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Fedor Pchelkin <aissur0002@gmail.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Christian Brauner <brauner@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "test_dev" pointer is freed but then returned to the caller.
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This has always been the rule: fdtables have several bitmaps in them,
and as a result they have to be sized properly for bitmaps. We walk
those bitmaps in chunks of 'unsigned long' in serveral cases, but even
when we don't, we use the regular kernel bitops that are defined to work
on arrays of 'unsigned long', not on some byte array.
Now, the distinction between arrays of bytes and 'unsigned long'
normally only really ends up being noticeable on big-endian systems, but
Fedor Pchelkin and Alexey Khoroshilov reported that copy_fd_bitmaps()
could be called with an argument that wasn't even a multiple of
BITS_PER_BYTE. And then it fails to do the proper copy even on
little-endian machines.
The bug wasn't in copy_fd_bitmap(), but in sane_fdtable_size(), which
didn't actually sanitize the fdtable size sufficiently, and never made
sure it had the proper BITS_PER_LONG alignment.
That's partly because the alignment historically came not from having to
explicitly align things, but simply from previous fdtable sizes, and
from count_open_files(), which counts the file descriptors by walking
them one 'unsigned long' word at a time and thus naturally ends up doing
sizing in the proper 'chunks of unsigned long'.
But with the introduction of close_range(), we now have an external
source of "this is how many files we want to have", and so
sane_fdtable_size() needs to do a better job.
This also adds that explicit alignment to alloc_fdtable(), although
there it is mainly just for documentation at a source code level. The
arithmetic we do there to pick a reasonable fdtable size already aligns
the result sufficiently.
In fact,clang notices that the added ALIGN() in that function doesn't
actually do anything, and does not generate any extra code for it.
It turns out that gcc ends up confusing itself by combining a previous
constant-sized shift operation with the variable-sized shift operations
in roundup_pow_of_two(). And probably due to that doesn't notice that
the ALIGN() is a no-op. But that's a (tiny) gcc misfeature that doesn't
matter. Having the explicit alignment makes sense, and would actually
matter on a 128-bit architecture if we ever go there.
This also adds big comments above both functions about how fdtable sizes
have to have that BITS_PER_LONG alignment.
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
In nfs4_callback_devicenotify(), if we don't find a matching entry for
the deviceid, we're left with a pointer to 'struct nfs_server' that
actually points to the list of super blocks associated with our struct
nfs_client.
Furthermore, even if we have a valid pointer, nothing pins the super
block, and so the struct nfs_server could end up getting freed while
we're using it.
Since all we want is a pointer to the struct pnfs_layoutdriver_type,
let's skip all the iteration over super blocks, and just use APIs to
find the layout driver directly.
When switching zones or network namespaces without doing a ct clear in
between, it is now leaking a reference to the old ct entry. That's
because tcf_ct_skb_nfct_cached() returns false and
tcf_ct_flow_table_lookup() may simply overwrite it.
The fix is to, as the ct entry is not reusable, free it already at
tcf_ct_skb_nfct_cached().
Reported-by: Florian Westphal <fw@strlen.de> Fixes: 2f131de361f6 ("net/sched: act_ct: Fix flow table lookup after ct clear or switching zones") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Its the same as nf_conntrack_put(), but without the
need for an indirect call. The downside is a module dependency on
nf_conntrack, but all of these already depend on conntrack anyway.
Cc: Paul Blakey <paulb@mellanox.com> Cc: dev@openvswitch.org Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
These are negative tests, testing TLS code rejects certain
operations. They won't pass without TLS enabled, pure TCP
accepts those operations.
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org> Fixes: d87d67fd61ef ("selftests: tls: test splicing cmsgs") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang static analysis reports this representative issue
rvu_npc.c:898:15: warning: Assigned value is garbage
or undefined
req.match_id = action.match_id;
^ ~~~~~~~~~~~~~~~
The initial setting of action is conditional on
if (is_mcam_entry_enabled(...))
The later check of action.op will sometimes be garbage.
So initialize action.
Reduce setting of
*(u64 *)&action = 0x00;
to
*(u64 *)&action = 0;
Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the possible failure of the allocation, devm_kzalloc() may return NULL
pointer.
Therefore, it should be better to check the 'db' in order to prevent
the dereference of NULL pointer.
Fixes: 10615907e9b51 ("net: sparx5: switchdev: adding frame DMA functionality") Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the link layer is terminating, x25->neighbour will be set to NULL
in x25_disconnect(). As a result, it could cause null-ptr-deref bugs in
x25_sendmsg(),x25_recvmsg() and x25_connect(). One of the bugs is
shown below.
The code sets NULL to x25->neighbour in position (1) and dereferences
x25->neighbour in position (2), which could cause null-ptr-deref bug.
This patch adds lock_sock() in x25_kill_by_neigh() in order to synchronize
with x25_sendmsg(), x25_recvmsg() and x25_connect(). What`s more, the
sock held by lock_sock() is not NULL, because it is extracted from x25_list
and uses x25_list_lock to synchronize.
Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix build errors when PTP_1588_CLOCK=m and SPARX5_SWTICH=y.
arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ethtool.o: in function `sparx5_get_ts_info':
sparx5_ethtool.c:(.text+0x146): undefined reference to `ptp_clock_index'
arc-linux-ld: sparx5_ethtool.c:(.text+0x146): undefined reference to `ptp_clock_index'
arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o: in function `sparx5_ptp_init':
sparx5_ptp.c:(.text+0xd56): undefined reference to `ptp_clock_register'
arc-linux-ld: sparx5_ptp.c:(.text+0xd56): undefined reference to `ptp_clock_register'
arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o: in function `sparx5_ptp_deinit':
sparx5_ptp.c:(.text+0xf30): undefined reference to `ptp_clock_unregister'
arc-linux-ld: sparx5_ptp.c:(.text+0xf30): undefined reference to `ptp_clock_unregister'
arc-linux-ld: sparx5_ptp.c:(.text+0xf38): undefined reference to `ptp_clock_unregister'
arc-linux-ld: sparx5_ptp.c:(.text+0xf46): undefined reference to `ptp_clock_unregister'
arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o:sparx5_ptp.c:(.text+0xf46): more undefined references to `ptp_clock_unregister' follow
Fixes: 3cfa11bac9bb ("net: sparx5: add the basic sparx5 driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Steen Hegelund <steen.hegelund@microchip.com> Cc: Bjarni Jonasson <bjarni.jonasson@microchip.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After disable sriov, VF still has some config and info need to be
cleaned, which configured by PF. This patch clean the HW config
and SW struct vport->vf_info.
Fixes: fa8d82e853e8 ("net: hns3: Add support of .sriov_configure in HNS3 driver") Signed-off-by: Peng Li<lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If __nfs_pageio_add_request() fails to add the request, it will return
with either desc->pg_error < 0, or mirror->pg_recoalesce will be set, so
we are guaranteed either to exit the function altogether, or to loop.
However if there is nothing left in mirror->pg_list to coalesce, we must
exit, so make sure that we clear mirror->pg_recoalesce every time we
loop.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: 70536bf4eb07 ("NFS: Clean up reset of the mirror accounting variables") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The purpose of the last test case is to test VXLAN encapsulation and
decapsulation when the underlay lookup takes place in a non-default VRF.
This is achieved by enslaving the physical device of the tunnel to a
VRF.
The binding of the VXLAN UDP socket to the VRF happens when the VXLAN
device itself is opened, not when its physical device is opened. This
was also mentioned in the cited commit ("tests that moving the underlay
from a VRF to another works when down/up the VXLAN interface"), but the
test did something else.
Fix it by reopening the VXLAN device instead of its physical device.
Before:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [FAIL]
After:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [ OK ]
Fixes: 03f1c26b1c56 ("test/net: Add script for VXLAN underlay in a VRF") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220324200514.1638326-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A Broadcom AC201 PHY (same entry as 5241) would be flagged by the
Broadcom UniMAC MDIO controller as not completing the turn around
properly since the PHY expects 65 MDC clock cycles to complete a write
cycle, and the MDIO controller was only sending 64 MDC clock cycles as
determined by looking at a scope shot.
This would make the subsequent read fail with the UniMAC MDIO controller
command field having MDIO_READ_FAIL set and we would abort the
brcm_fet_config_init() function and thus not probe the PHY at all.
After issuing a software reset, wait for at least 1ms which is well
above the 1us reset delay advertised by the datasheet and issue a dummy
read to let the PHY turn around the line properly. This read
specifically ignores -EIO which would be returned by MDIO controllers
checking for the line being turned around.
If we have a genuine reaad failure, the next read of the interrupt
status register would pick it up anyway.
Currently, when PF set VF VLAN, it sends notify mailbox to VF
if VF alive. VF stop its traffic, and send request mailbox
to PF, then PF updates VF VLAN. It's a bit complex. If VF is
killed before sending request, PF will not set VF VLAN without
any log.
This patch refines the process, PF can set VF VLAN direclty,
and then notify the VF. If VF is resetting at that time, the
notify may be dropped, so VF should query it after reset finished.
Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Printing the whole MAC addresse may bring security risks. Therefore,
the MAC address is partially encrypted to improve security.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding port base VLAN, vf VLAN need to remove from HW and modify
the vlan state in vf VLAN list as false. If the periodicity task is
freeing the same node, it may cause "use after free" error.
This patch adds a vlan list lock to protect the vlan list.
Currently, Port base vlan is initiated by PF and configured to its VFs,
by using command "ip link set <pf name> vf <vf id> vlan <vlan id>".
When a global reset was triggered, the hardware vlan table and the soft
recorded vlan information will be cleared by PF, and restored them until
VFs were ready. There is a short time window between the table had been
cleared and before table restored. If configured a new port base vlan tag
at this moment, driver will check the soft recorded vlan information,
and find there hasn't the old tag in it, which causing a warning print.
Due to the port base vlan is managed by PF, so the VFs's port base vlan
restoring should be handled by PF when PF was ready.
This patch fixes it.
Fixes: 039ba863e8d7 ("net: hns3: optimize the filter table entries handling when resetting") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the MAC address A is configured to vport A and then vport B. The MAC
address of vport A in the hardware becomes invalid. If the address of
vport A is changed to MAC address B, the driver needs to delete the MAC
address A of vport A. Due to the MAC address A of vport A has become
invalid in the hardware entry, so "-ENOENT" is returned. In this case, the
"used_umv_size" value recorded in driver is not updated. As a result, the
MAC entry status of the software is inconsistent with that of the hardware.
Therefore, the driver updates the umv size even if the MAC entry cannot be
found. Ensure that the software and hardware status is consistent.
Fixes: ee4bcd3b7ae4 ("net: hns3: refactor the MAC address configure") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
is_xen_pmu() is taking the cpu number as parameter, but it is not using
it. Instead it just tests whether the Xen PMU initialization on the
current cpu did succeed. As this test is done by checking a percpu
pointer, preemption needs to be disabled in order to avoid switching
the cpu while doing the test. While resuming from suspend() this seems
not to be the case:
[ 88.082751] ACPI: PM: Low-level resume complete
[ 88.087933] ACPI: EC: EC started
[ 88.091464] ACPI: PM: Restoring platform NVS memory
[ 88.097166] xen_acpi_processor: Uploading Xen processor PM info
[ 88.103850] Enabling non-boot CPUs ...
[ 88.108128] installing Xen timer for CPU 1
[ 88.112763] BUG: using smp_processor_id() in preemptible [00000000] code: systemd-sleep/7138
[ 88.122256] caller is is_xen_pmu+0x12/0x30
[ 88.126937] CPU: 0 PID: 7138 Comm: systemd-sleep Tainted: G W 5.16.13-2.fc32.qubes.x86_64 #1
[ 88.137939] Hardware name: Star Labs StarBook/StarBook, BIOS 7.97 03/21/2022
[ 88.145930] Call Trace:
[ 88.148757] <TASK>
[ 88.151193] dump_stack_lvl+0x48/0x5e
[ 88.155381] check_preemption_disabled+0xde/0xe0
[ 88.160641] is_xen_pmu+0x12/0x30
[ 88.164441] xen_smp_intr_init_pv+0x75/0x100
Fix that by replacing is_xen_pmu() by a simple boolean variable which
reflects the Xen PMU initialization state on cpu 0.
Modify xen_pmu_init() to return early in case it is being called for a
cpu other than cpu 0 and the boolean variable not being set.
Fixes: bf6dfb154d93 ("xen/PMU: PMU emulation code") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20220325142002.31789-1-jgross@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When registering a clock that doesn't have a recalc_rate implementation,
and doesn't have its parent registered yet, we initialize the clk_core
rate and 'req_rate' fields to 0.
The rate field is later updated when the parent is registered in
clk_core_reparent_orphans_nolock() using __clk_recalc_rates(), but the
'req_rate' field is never updated.
This leads to an issue in clk_set_rate_range() and clk_put(), since
those functions will call clk_set_rate() with the content of 'req_rate'
to provide drivers with the opportunity to change the rate based on the
new boundaries. In this case, we would call clk_set_rate() with a rate
of 0, effectively enforcing the minimum allowed for this clock whenever
we would call one of those two functions, even though the actual rate
might be within range.
Let's fix this by setting 'req_rate' in
clk_core_reparent_orphans_nolock() with the rate field content just
updated by the call to __clk_recalc_rates().
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, but virtio-vsock
driver uses VQs in the probe function to fill rx and event VQs
with new buffers.
Let's fix this, calling virtio_device_ready() before using VQs
in the probe function.
Fixes: 0ea9e1d3a9e3 ("VSOCK: Introduce virtio_transport.ko") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Complete the driver configuration, reading the negotiated features,
before using the VQs in the virtio_vsock_probe().
Fixes: 53efbba12cc7 ("virtio/vsock: enable SEQPACKET for transport") Suggested-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we fill VQs with empty buffers and kick the host, it may send
an interrupt. `vdev->priv` must be initialized before this since it
is used in the virtqueue callbacks.
Fixes: 0deab087b16a ("vsock/virtio: use RCU to avoid use-after-free on the_virtio_vsock") Suggested-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: aec89f78cf01 ("clk: qcom: Add support for msm8994 global clock controller") Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20220319174940.341137-1-konrad.dybcio@somainline.org Tested-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The new PMU for s390 counts the execution of certain CPU instructions.
The root cause is the extremely small run time of the mytest program. It
just executes some assembly instructions and then exits.
In above invocation the instruction is executed exactly one time (-c1
option). The PMU is expected to report this one time execution by a
counter value of one, but fails to do so in some cases, not all.
Debugging reveals the invocation of the child process is done
*before* the counter events are installed and enabled.
Tracing reveals that sometimes the child process starts and exits before
the event is installed on all CPUs. The more CPUs the machine has, the
more often this miscount happens.
Fix this by reversing the start of the work load after the events have
been installed on the specified CPUs. Now the comment also matches the
code.
Output after:
# perf stat -a -e new_pmu/INSTRUCTION_7/ -- mytest -c1 7
Currently kdb_putarea_size() uses copy_from_kernel_nofault() to write *to*
arbitrary kernel memory. This is obviously wrong and means the memory
modify ('mm') command is a serious risk to debugger stability: if we poke
to a bad address we'll double-fault and lose our debug session.
Fix this the (very) obvious way.
Note that there are two Fixes: tags because the API was renamed and this
patch will only trivially backport as far as the rename (and this is
probably enough). Nevertheless Christoph's rename did not introduce this
problem so I wanted to record that!
Fixes: fe557319aa06 ("maccess: rename probe_kernel_{read,write} to copy_{from,to}_kernel_nofault") Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)") Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20220128144055.207267-1-daniel.thompson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
