As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083b901f001794038a08b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
drivers/staging/vme_user/vme_tsi148.c:1757 tsi148_dma_list_add() warn:
'&entry->list' not removed from list
In tsi148_dma_list_add(), the error path "goto err_dma" will not
remove entry->list from list->entries, but entry will be freed,
then list traversal may cause UAF.
Fix by removeing it from list->entries before free().
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
This fixes a concurrency issue addressed in commit 34cb27528398 ("UIO: Fix
concurrency issue"):
"In a SMP case there was a race condition issue between
Uio_pdrv_genirq_irqcontrol() running on one CPU and irq handler on
another CPU. Fix it by spin_locking shared resources access inside irq
handler."
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
merged, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(), thus, both had the same concurrency issue
mentioned by the above commit. However, the above patch was only applied to
the "uio_pdrv_genirq" driver.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: 0a0c3b5a24bd ("Add new uio device for dynamic memory allocation") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-3-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-while-atomic bug that commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") was trying to
fix. Thus, this fixes the missing unlock in irqcontrol() by importing the
implementation of irqcontrol() handler from the "uio_pdrv_genirq" driver.
In the end, it reverts commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") and change
disable_irq() to disable_irq_nosync().
It is worth noting that this still does not address the concurrency issue
fixed by commit 34cb27528398 ("UIO: Fix concurrency issue"). It will be
addressed separately in the next commits.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: b74351287d4b ("uio: fix a sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-2-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error, the 'dev' and name needs be
freed. Add a release function, and then call put_device() in the
error path, so the name is freed in kobject_cleanup() and to the
'dev' is freed in release function.
Fixes: 2e4c77bea3d8 ("m68k: dio - Kill warn_unused_result warnings") Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109064036.1835346-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 ways to create IPoIB PKEY child interfaces:
1) Writing a PKEY to /sys/class/net/<ib parent interface>/create_child.
2) Using netlink with iproute.
While with sysfs the child interface has the same number of tx and
rx queues as the parent, with netlink there will always be 1 tx
and 1 rx queue for the child interface. That's because the
get_num_tx/rx_queues() netlink ops are missing and the default value
of 1 is taken for the number of queues (in rtnl_create_link()).
This change adds the get_num_tx/rx_queues() ops which allows for
interfaces with multiple queues to be created over netlink. This
constant only represents the max number of tx and rx queues on that
net device.
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path.
Fixes: ef5d862734b8 ("[PATCH] Add Geode HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path.
Fixes: 96d63c0297cc ("[PATCH] Add AMD HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/snic/snic_disc.c:307 snic_tgt_create() warn:
'&tgt->list' not removed from list
If device_add() fails in snic_tgt_create(), tgt will be freed, but
tgt->list will not be removed from snic->disc.tgt_list, then list traversal
may cause UAF.
Remove from snic->disc.tgt_list before free().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221117035100.2944812-1-cuigaosheng1@huawei.com Acked-by: Narsimhulu Musini <nmusini@cisco.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcoe_init() calls fcoe_transport_attach(&fcoe_sw_transport), but when
fcoe_if_init() fails, &fcoe_sw_transport is not detached and leaves freed
&fcoe_sw_transport on fcoe_transports list. This causes panic when
reinserting module.
BUG: unable to handle page fault for address: fffffbfff82e2213
RIP: 0010:fcoe_transport_attach+0xe1/0x230 [libfcoe]
Call Trace:
<TASK>
do_one_initcall+0xd0/0x4e0
load_module+0x5eee/0x7210
...
Fixes: 78a582463c1e ("[SCSI] fcoe: convert fcoe.ko to become an fcoe transport provider driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221115092442.133088-1-chenzhongjin@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipr_init() will not call unregister_reboot_notifier() when
pci_register_driver() fails, which causes a WARNING. Call
unregister_reboot_notifier() when pci_register_driver() fails.
If device_register() returns an error, the name allocated by dev_set_name()
needs to be freed. As the comment of device_register() says, one should use
put_device() to give up the reference in the error path. Fix this by
calling put_device(), then the name can be freed in kobject_cleanup().
The 'fcf' is freed in fcoe_fcf_device_release(), so the kfree() in the
error path can be removed.
The 'ctlr' is freed in fcoe_ctlr_device_release(), so don't use the error
label, just return NULL after calling put_device().
Fixes: 9a74e884ee71 ("[SCSI] libfcoe: Add fcoe_sysfs") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112094310.3633291-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_rphy() returns an error, the 'rphy' allocated in
sas_end_device_alloc() needs to be freed. Address this by calling
sas_rphy_free() in the error path.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221111043012.1074466-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_phy() returns an error, hpsa_free_sas_phy() can not be
called to free the memory because the port and the phy have not been added
yet.
Replace hpsa_free_sas_phy() with sas_phy_free() and kfree() to avoid kernel
crash in this case.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221110151129.394389-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MAC is connected to a 10 Mb/s PHY and the PTP clock is derived
from the MAC reference clock (default), the clk_ptp_rate becomes too
small and the calculated sub second increment becomes 0 when computed by
the stmmac_config_sub_second_increment() function within
stmmac_init_tstamp_counter().
Therefore, the subsequent div_u64 in stmmac_init_tstamp_counter()
operation triggers a divide by 0 exception as shown below.
[ 95.062067] socfpga-dwmac ff700000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 95.076440] socfpga-dwmac ff700000.ethernet eth0: PHY [stmmac-0:08] driver [NCN26000] (irq=49)
[ 95.095964] dwmac1000: Master AXI performs any burst length
[ 95.101588] socfpga-dwmac ff700000.ethernet eth0: No Safety Features support found
[ 95.109428] Division by zero in kernel.
[ 95.113447] CPU: 0 PID: 239 Comm: ifconfig Not tainted 6.1.0-rc7-centurion3-1.0.3.0-01574-gb624218205b7-dirty #77
[ 95.123686] Hardware name: Altera SOCFPGA
[ 95.127695] unwind_backtrace from show_stack+0x10/0x14
[ 95.132938] show_stack from dump_stack_lvl+0x40/0x4c
[ 95.137992] dump_stack_lvl from Ldiv0+0x8/0x10
[ 95.142527] Ldiv0 from __aeabi_uidivmod+0x8/0x18
[ 95.147232] __aeabi_uidivmod from div_u64_rem+0x1c/0x40
[ 95.152552] div_u64_rem from stmmac_init_tstamp_counter+0xd0/0x164
[ 95.158826] stmmac_init_tstamp_counter from stmmac_hw_setup+0x430/0xf00
[ 95.165533] stmmac_hw_setup from __stmmac_open+0x214/0x2d4
[ 95.171117] __stmmac_open from stmmac_open+0x30/0x44
[ 95.176182] stmmac_open from __dev_open+0x11c/0x134
[ 95.181172] __dev_open from __dev_change_flags+0x168/0x17c
[ 95.186750] __dev_change_flags from dev_change_flags+0x14/0x50
[ 95.192662] dev_change_flags from devinet_ioctl+0x2b4/0x604
[ 95.198321] devinet_ioctl from inet_ioctl+0x1ec/0x214
[ 95.203462] inet_ioctl from sock_ioctl+0x14c/0x3c4
[ 95.208354] sock_ioctl from vfs_ioctl+0x20/0x38
[ 95.212984] vfs_ioctl from sys_ioctl+0x250/0x844
[ 95.217691] sys_ioctl from ret_fast_syscall+0x0/0x4c
[ 95.222743] Exception stack(0xd0ee1fa8 to 0xd0ee1ff0)
[ 95.227790] 1fa0: 00574c4fbe9aeca40000000300008914be9aeca4be9aec50
[ 95.235945] 1fc0: 00574c4fbe9aeca40059f07800000036be9aee8cbe9aef7a0000001500000000
[ 95.244096] 1fe0: 005a01f0be9aec38004d7484b6e67d74
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 9238f36a5a50 ("Bluetooth: Add request cmd_complete and cmd_status functions") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d78960 ("Bluetooth: Fix/implement Three-wire reliable packet sending") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c1976d ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367ffb ("Bluetooth: btusb: Implement driver internal packet reassembly") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
TX/RX callback handlers (ntb_netdev_tx_handler(),
ntb_netdev_rx_handler()) can be called in interrupt
context via the DMA framework when the respective
DMA operations have completed. As such, any calls
by these routines to free skb's, should use the
interrupt context safe dev_kfree_skb_any() function.
Previously, these callback handlers would call the
interrupt unsafe version of dev_kfree_skb(). This has
not presented an issue on Intel IOAT DMA engines as
that driver utilizes tasklets rather than a hard
interrupt handler, like the AMD PTDMA DMA driver.
On AMD systems, a kernel WARNING message is
encountered, which is being issued from
skb_release_head_state() due to in_hardirq()
being true.
Besides the user visible WARNING from the kernel,
the other symptom of this bug was that TCP/IP performance
across the ntb_netdev interface was very poor, i.e.
approximately an order of magnitude below what was
expected. With the repair to use dev_kfree_skb_any(),
kernel WARNINGs from skb_release_head_state() ceased
and TCP/IP performance, as measured by iperf, was on
par with expected results, approximately 20 Gb/s on
AMD Milan based server. Note that this performance
is comparable with Intel based servers.
Fixes: 765ccc7bc3d91 ("ntb_netdev: correct skb leak") Fixes: 548c237c0a997 ("net: Add support for NTB virtual ethernet device") Signed-off-by: Eric Pilmore <epilmore@gigaio.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20221209000659.8318-1-epilmore@gigaio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In these two cases, dev_kfree_skb() is called consume the xmited SKB,
so replace it with dev_consume_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In scc_discard_buffers(), dev_kfree_skb() is called to discard the SKBs,
so replace it with dev_kfree_skb_irq().
In scc_net_tx(), dev_kfree_skb() is called to drop the SKB that exceed
queue length, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
In this case, the lock is used to protected 'bp', so we can move
dev_kfree_skb() after the spin_unlock_irqrestore().
Fixes: 4796417417a6 ("dnet: Dave DNET ethernet controller driver (updated)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in xemaclite_tx_timeout() to
drop the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: bb81b2ddfa19 ("net: add Xilinx emac lite device driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in bmac_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in mace_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a race condition in vxlan that when deleting a vxlan device
during receiving packets, there is a possibility that the sock is
released after getting vxlan_sock vs from sk_user_data. Then in
later vxlan_ecn_decapsulate(), vxlan_get_sk_family() we will got
NULL pointer dereference. e.g.
Fix this by waiting for all sk_user_data reader to finish before
releasing the sock.
Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Fixes: 6a93cc905274 ("udp-tunnel: Add a few more UDP tunnel APIs") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is traced to the netdev and fst_card_info are not freed
when removes one fst in fst_remove_one(), which may trigger oom if
repeated insmod and rmmod module.
Fix it by adding free_netdev() and kfree() in fst_remove_one(), just as
the operations on the error handling path in fst_add_one().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in free_tx_buffers() to drop
the SKBs in tx buffers, when the card is down, so replace it with
dev_kfree_skb_irq() here.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If vp alloc failed in qlcnic_sriov_init(), all previously allocated vp
needs to be freed.
Fixes: f197a7aa6288 ("qlcnic: VF-PF communication channel implementation") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
vmci_transport_dgram_enqueue() does not check the return value
of memcpy_from_msg(). If memcpy_from_msg() fails, it is possible that
uninitialized memory contents are sent unintentionally instead of user's
message in the datagram to the destination. Return with an error if
memcpy_from_msg() fails.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f7db23a07af ("vmci_transport: switch ->enqeue_dgram, ->enqueue_stream and ->dequeue_stream to msghdr") Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the blk_classic option is enabled, non-blktrace events must be
filtered out. Otherwise, events of other types are output in the blktrace
classic format, which is unexpected.
The problem can be triggered in the following ways:
Fix to return a negative error code instead of 0 when
brcmf_chip_set_active() fails. In addition, change the return
value for brcmf_pcie_exit_download_state() to keep consistent.
Fixes: d380ebc9b6fb ("brcmfmac: rename chip download functions") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1669959342-27144-1-git-send-email-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
As the coda_iram_alloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
In configure_channels(), we should call of_node_put() when breaking
out of for_each_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: c5f5d0f99794 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host().
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host(), besides, other resources also need be
released.
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
Fix this by checking the return value and goto error path which
will call mmc_free_host().
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, the timer added before mmc_add_host() needs be del.
And this patch fixes another missing call mmc_free_host() if usb_control_msg()
fails.
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, free_irq() also needs be called.
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and calling mmc_free_host() in the
error path, besides, led_classdev_unregister() and pm_runtime_disable() also
need be called.
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host().
Fixes: d96be879ff46 ("mmc: Add a MX2/MX3 specific SDHC driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221101063023.1664968-4-yangyingliang@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host().
socket dynamically created is not released when getting an unintended
address family type in rpc_sockname(), direct to out_release for calling
sock_release().
Fixes: 2e738fdce22f ("SUNRPC: Add API to acquire source address") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "ignore_updelay" variable needs to be initialized to false.
Fixes: f8a65ab2f3ff ("bonding: fix link recovery in mode 2 when updelay is nonzero") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/Y4SWJlh3ohJ6EPTL@kili Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:f086ba9d5389c ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in radeon_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d8ade3526b2a ("drm/radeon: handle non-VGA class pci devices with ATRM") Fixes: c61e2775873f ("drm/radeon: split ATRM support out from the ATPX handler (v3)") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're asked to recover open state while a delegation return is
outstanding, then the state manager thread cannot use a cached open, so
if the server returns a delegation, we can end up deadlocked behind the
pending delegreturn.
To avoid this problem, let's just ask the server not to give us a
delegation unless we're explicitly reclaiming one.
Fixes: be36e185bd26 ("NFSv4: nfs4_open_recover_helper() must set share access") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
If clk_register() fails, @pll->rate_table may have allocated memory by
kmemdup(), so it needs to be freed, otherwise will cause memory leak
issue, this patch fixes it.
Fixes: 90c590254051 ("clk: rockchip: add clock type for pll clocks and pll used on rk3066") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Link: https://lore.kernel.org/r/20221123091201.199819-1-xiujianfeng@huawei.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/seq/seq_clientmgr.c:509:22
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_seq_deliver_single_event.constprop.21+0x191/0x2f0
snd_seq_deliver_event+0x1a2/0x350
snd_seq_kernel_client_dispatch+0x8b/0xb0
snd_seq_client_notify_subscription+0x72/0xa0
snd_seq_ioctl_subscribe_port+0x128/0x160
snd_seq_kernel_client_ctl+0xce/0xf0
snd_seq_oss_create_client+0x109/0x15b
alsa_seq_oss_init+0x11c/0x1aa
do_one_initcall+0x80/0x440
kernel_init_freeable+0x370/0x3c3
kernel_init+0x1b/0x190
ret_from_fork+0x1f/0x30
</TASK>
This is no bugfix (so no Fixes: tag is necessary) as it is
taken care of in hid_sensor_custom_add_attributes().
The motivation for this patch is that:
hid_sensor_custom_field.attr_name and
hid_sensor_custom_field.attrs
has the size of HID_CUSTOM_TOTAL_ATTRS and used in same context.
We compare against HID_CUSTOM_TOTAL_ATTRS when
looping through hid_custom_attrs.
We will silent the smatch error:
hid_sensor_custom_add_attributes() error: buffer overflow
'hid_custom_attrs' 8 <= 10
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b090 ("[media] s5p-fimc: Add the media device driver") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbce5 ("[media] solo6x10: sync to latest code from Bluecherry's git repo") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The input parameter @fields is type of struct ima_template_field ***, so
when allocates array memory for @fields, the size of element should be
sizeof(**field) instead of sizeof(*field).
Actually the original code would not cause any runtime error, but it's
better to make it logically right.
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e6d ("regulator: map consumer regulator based on device tree") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because we forget to check boundary after adjust compose->height
int V4L2_SEL_TGT_CROP case. Add v4l2_rect_map_inside() to fix this problem
for this case.
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible that skb is freed in ath9k_htc_rx_msg(), then
usb_submit_urb() fails and we try to free skb again. It causes
use-after-free bug. Moreover, if alloc_skb() fails, urb->context becomes
NULL but rx_buf is not freed and there can be a memory leak.
The patch removes unnecessary nskb and makes skb processing more clear: it
is supposed that ath9k_htc_rx_msg() either frees old skb or passes its
managing to another callback function.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 03fb92a432ea ("ath9k: hif_usb: fix race condition between usb_get_urb() and usb_kill_anchored_urbs()") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220725151359.283704-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
When kfifo_alloc fails, the refcount of chdev->dev is left incremental.
We should use put_device(&chdev->dev) to decrease the ref count of
chdev->dev to avoid refcount leak.
Link: https://lkml.kernel.org/r/20221203085721.13146-1-caixinchen1@huawei.com Fixes: e8de370188d0 ("rapidio: add mport char device driver") Signed-off-by: Cai Xinchen <caixinchen1@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Wang Weiyang <wangweiyang2@huawei.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
loop0: detected capacity change from 0 to 64
==================================================================
BUG: KASAN: slab-out-of-bounds in hfs_asc2mac+0x467/0x9a0
fs/hfs/trans.c:133
Write of size 1 at addr ffff88801848314e by task syz-executor391/3632
If in->len is much larger than HFS_NAMELEN(31) which is the maximum
length of an HFS filename, a OOB write could occur in hfs_asc2mac(). In
that case, when the dst reaches the boundary, the srclen is still
greater than 0, which causes a OOB write.
Fix this by adding a check on dstlen in while() before writing to dst
address.
If kfifo_alloc() fails in mport_cdev_open(), goto err_fifo and just free
priv. But priv is still in the chdev->file_list, then list traversal
may cause UAF. This fixes the following smatch warning:
drivers/rapidio/devices/rio_mport_cdev.c:1930 mport_cdev_open() warn: '&priv->list' not removed from list
Link: https://lkml.kernel.org/r/20221123095147.52408-1-wangweiyang2@huawei.com Fixes: e8de370188d0 ("rapidio: add mport char device driver") Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sysv_nblocks() returns 'blocks' rather than 'res', which only counting
the number of triple-indirect blocks and causing sysv_getattr() gets a
wrong result.
[AV: this is actually a sysv counterpart of minixfs fix - 0fcd426de9d0 "[PATCH] minix block usage counting fix" in
historical tree; mea culpa, should've thought to check
fs/sysv back then...]
Check clk for NULL before calling clk_enable_unlocked where clk
is dereferenced. There is such check in other implementations
of clk_enable.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.") Signed-off-by: Anastasia Belova <abelova@astralinux.ru> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In xen_init_lock_cpu(), the @name has allocated new string by kasprintf(),
if bind_ipi_to_irqhandler() fails, it should be freed, otherwise may lead
to a memory leak issue, fix it.
Intel ICC -hotpatch inserts 2-byte "0x66 0x90" NOP at the start of each
function to reserve extra space for hot-patching, and currently it is not
possible to probe these functions because branch_setup_xol_ops() wrongly
rejects NOP with REP prefix as it treats them like word-sized branch
instructions.
BUG: KASAN: use-after-free in acpi_ut_remove_reference+0x3b/0x82
Read of size 1 at addr ffff888112afc460 by task modprobe/2111
CPU: 0 PID: 2111 Comm: modprobe Not tainted 6.1.0-rc7-dirty
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
Call Trace:
<TASK>
kasan_report+0xae/0xe0
acpi_ut_remove_reference+0x3b/0x82
acpi_ut_copy_iobject_to_iobject+0x3be/0x3d5
acpi_ds_store_object_to_local+0x15d/0x3a0
acpi_ex_store+0x78d/0x7fd
acpi_ex_opcode_1A_1T_1R+0xbe4/0xf9b
acpi_ps_parse_aml+0x217/0x8d5
...
</TASK>
The root cause of the problem is that the acpi_operand_object
is freed when acpi_ut_walk_package_tree() fails in
acpi_ut_copy_ipackage_to_ipackage(), lead to repeated release in
acpi_ut_copy_iobject_to_iobject(). The problem was introduced
by "8aa5e56eeb61" commit, this commit is to fix memory leak in
acpi_ut_copy_iobject_to_iobject(), repeatedly adding remove
operation, lead to "acpi_operand_object" used after free.
Fix it by removing acpi_ut_remove_reference() in
acpi_ut_copy_ipackage_to_ipackage(). acpi_ut_copy_ipackage_to_ipackage()
is called to copy an internal package object into another internal
package object, when it fails, the memory of acpi_operand_object
should be freed by the caller.
Fixes: 8aa5e56eeb61 ("ACPICA: Utilities: Fix memory leak in acpi_ut_copy_iobject_to_iobject") Signed-off-by: Li Zetao <lizetao1@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error, the name allocated by dev_set_name()
need be freed. It should use put_device() to give up the reference in the
error path, so that the name can be freed in kobject_cleanup(), and
list_del() is called to delete the port from rio_mports.
Link: https://lkml.kernel.org/r/20221114152636.2939035-3-yangyingliang@huawei.com Fixes: 2aaf308b95b2 ("rapidio: rework device hierarchy and introduce mport class of devices") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "rapidio: fix three possible memory leaks".
This patchset fixes three name leaks in error handling.
- patch #1 fixes two name leaks while rio_add_device() fails.
- patch #2 fixes a name leak while rio_register_mport() fails.
This patch (of 2):
If rio_add_device() returns error, the name allocated by dev_set_name()
need be freed. It should use put_device() to give up the reference in the
error path, so that the name can be freed in kobject_cleanup(), and the
'rdev' can be freed in rio_release_dev().
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()").
This restores the previous behaviour by using newly introduced
DEFINE_SIMPLE_ATTRIBUTE_SIGNED instead of DEFINE_SIMPLE_ATTRIBUTE.
Link: https://lkml.kernel.org/r/20220919172418.45257-3-akinobu.mita@gmail.com Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Oscar Salvador <osalvador@suse.de> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "fix error when writing negative value to simple attribute
files".
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), but some attribute files want to accept a negative
value.
This patch (of 3):
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), so we have to use a 64-bit value to write a
negative value.
This adds DEFINE_SIMPLE_ATTRIBUTE_SIGNED for a signed value.
Link: https://lkml.kernel.org/r/20220919172418.45257-1-akinobu.mita@gmail.com Link: https://lkml.kernel.org/r/20220919172418.45257-2-akinobu.mita@gmail.com Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Oscar Salvador <osalvador@suse.de> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
gic_probe() calls pm_runtime_get_sync() and added fail path as
rpm_put to put usage_counter. However, pm_runtime_get_sync()
will increment usage_counter even it failed. Fix it by replacing it with
pm_runtime_resume_and_get() to keep usage counter balanced.
Fixes: 9c8edddfc992 ("irqchip/gic: Add platform driver for non-root GICs that require RPM") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221124065150.22809-1-shangxiaojing@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
move dev_set_name() after pnp_add_id() to avoid memory leak.
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_set_name() allocates memory for name, it need be freed
when module exiting, call put_device() to give up reference,
so that it can be freed in kobject_cleanup() when the refcount
hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 17a1d523aa58 ("MIPS: APRP: Add VPE loader support for CMP platforms.") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
it need be freed when module exiting, call put_device() to give up
reference, so that it can be freed in kobject_cleanup() when the
refcount hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
