Olivier Benjamin [Fri, 20 Jun 2025 15:21:34 +0000 (17:21 +0200)]
arm64: dts: rockchip: describe I2c Bus 1 and IMX258 world camera on PinePhone Pro
Add the description of the rear/world camera (IMX258) on the PinePhone Pro
to the device dts file.
It receives commands on the I2C Bus 1 at address 0x1a and transmits data
over CSI-MIPI.
The I2C address for IMX258 can be found in the IMX258-0AQH5 Software
Reference Manual, page 24, section 2.3.1: 0b0011010 = 0x1a.
Section 3 indicates the module has 4 pairs of data lines. While 4-lane
mode is nominal, 2-lane mode should also be supported.
The pin muxing info was extracted from the PinePhone Pro schematic v1.0
as well as the RK3399 datasheet revision 1.8.
Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
of IO functions for the SoC pins. Page 52 shows GPIO1_A0, page 54 shows
GPIO2_D4.
For I2C power, the PinePhone Pro schematic page 11 quadrants A4 and A5:
RK3399_J.AA8 and RK3399_J.Y8 get power from vcaa1v8_codec, so turn it on
The IMX258 also uses the following regulators, expected by its driver:
- vana (2.8V analog), called AVDD2V8_DVP on P.18 q.C1 and derived from
VCC1V8_S3 on P.13 q.B2
- vdig (1.2V digital core), called DVDD_DVP on P.18 q.C1 and shown on
P.18 q.D3 to be equivalent to VCC1V2_DVP derived from VCC3V3_SYS on
P.13 q.B3. Note that this regulator's voltage is inconsistently
labeled either 1.2V or 1.5V
RK3399_J.AG1 is GPIO4_A1/I2C1_SDA, RK3399_J.Y6 is GPIO4_A2/I2C1_SCL
This is the default pinctrl "i2c1_xfer" for i2c1 from rk3399-base.
Jonas Karlman [Sat, 21 Jun 2025 11:38:57 +0000 (11:38 +0000)]
arm64: dts: rockchip: Fix pinctrl node names for RK3528
Following warnings can be observed with CHECK_DTBS=y for the RK3528:
rk3528-pinctrl.dtsi:101.36-105.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym0-led_dpx: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:108.38-112.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym0-led_link: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:115.36-119.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym0-led_spd: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:122.36-126.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym1-led_dpx: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:129.38-133.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym1-led_link: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:136.36-140.5: Warning (node_name_chars_strict):
/pinctrl/fephy/fephym1-led_spd: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:782.32-790.5: Warning (node_name_chars_strict):
/pinctrl/rgmii/rgmii-rx_bus2: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:793.32-801.5: Warning (node_name_chars_strict):
/pinctrl/rgmii/rgmii-tx_bus2: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:804.36-810.5: Warning (node_name_chars_strict):
/pinctrl/rgmii/rgmii-rgmii_clk: Character '_' not recommended in node name
rk3528-pinctrl.dtsi:813.36-823.5: Warning (node_name_chars_strict):
/pinctrl/rgmii/rgmii-rgmii_bus: Character '_' not recommended in node name
Quentin Schulz [Fri, 27 Jun 2025 10:53:57 +0000 (12:53 +0200)]
arm64: dts: rockchip: force PMIC reset behavior to restart PMU on RK3588 Tiger
The bootloader for RK3588 Tiger currently forces the PMIC reset behavior
(stored in RST_FUN bitfield in register SYS_CFG3 of the PMIC) to 0b1X
which is incorrect for our devices.
It is required to restart the PMU as otherwise the companion
microcontroller cannot detect the PMIC (and by extension the full
product and main SoC) being rebooted which is an issue as that is used
to reset a few things like the PWM beeper and watchdogs.
Let's add the new rockchip,reset-mode property to make sure the PMIC
reset behavior is the expected one.
Quentin Schulz [Fri, 27 Jun 2025 10:53:56 +0000 (12:53 +0200)]
arm64: dts: rockchip: force PMIC reset behavior to restart PMU on RK3588 Jaguar
The bootloader for RK3588 Jaguar currently forces the PMIC reset
behavior (stored in RST_FUN bitfield in register SYS_CFG3 of the PMIC)
to 0b1X which is incorrect for our devices.
It is required to restart the PMU as otherwise the companion
microcontroller cannot detect the PMIC (and by extension the full
product and main SoC) being rebooted which is an issue as that is used
to reset a few things like the PWM beeper and watchdogs.
Let's add the new rockchip,reset-mode property to make sure the PMIC
reset behavior is the expected one.
Quentin Schulz [Fri, 27 Jun 2025 10:53:55 +0000 (12:53 +0200)]
arm64: dts: rockchip: add header for RK8XX PMIC constants
To make it easier to read the device tree, let's add constants for the
rockchip,reset-mode property values that are currently only applicable
to RK806 PMIC.
arm64: dts: rockchip: theoretically enable Wi-Fi on ROCK 4D
The production version of the ROCK 4D appears to sport a AICSEMI
AIC8800D80 USB Wi-Fi + BT chipset. This chip does not yet have a
mainline driver.
Add the necessary rfkill node and wifi regulator node to at least make
it show up in lsusb output. The regulator is set as always-on, as like 2
hours deep into debugging why onboard_usb_dev.c wouldn't try enabling
the regulator the device needs to actually show up and thus bind to
onboard_usb_dev.c, I decided that it's not worth the effort.
arm64: dts: rockchip: adjust dcin regulator on ROCK 4D
The ROCK 4D's actual DC input is 5V, and the schematic names it as being
5V as well.
Rename the regulator, and change the voltage it claims to be at.
Furthermore, fix vcc_1v1_nldo_s3's vin-supply as coming from
vcc_5v0_sys, and not the DCIN, as per the schematic. This makes no
functional change; both regulators are always on, and one feeds into the
other.
arm64: dts: rockchip: fix PHY handling for ROCK 4D
Old revisions of the ROCK 4D board have a dedicated crystal to
supply the RTL8211F PHY's 25MHz clock input. At least some newer
revisions instead use REFCLKO25M_GMAC0_OUT. The DT already has
this half-prepared, but there are some issues:
1. The DT relies on auto-selecting the right PHY driver, which
requires that it works good enough to read the ID registers.
This does not work without the clock, which is handled by
the PHY driver. By updating the compatible to contain the
RTL8211F IDs, so that the operating system can choose the
right PHY driver without relying on a pre-powered PHY.
2. Despite the name REFCLKO25M_GMAC0_OUT could also provide a
different frequency, so ensure it is explicitly set to 25
MHz as expected by the PHY.
3. While at it switch from deprecated "enable-gpio" to standard
"enable-gpios".
arm64: dts: rockchip: Add HDMI PHY PLL clock source to VOP2 on rk3576
Since commit c871a311edf0 ("phy: rockchip: samsung-hdptx: Setup TMDS
char rate via phy_configure_opts_hdmi"), the workaround of passing the
rate from DW HDMI QP bridge driver via phy_set_bus_width() became
partially broken, as it cannot reliably handle mode switches anymore.
Attempting to fix this up at PHY level would not only introduce
additional hacks, but it would also fail to adequately resolve the
display issues that are a consequence of the system CRU limitations.
Instead, proceed with the solution already implemented for RK3588: make
use of the HDMI PHY PLL as a better suited DCLK source for VOP2. This
will not only address the aforementioned problem, but it should also
facilitate the proper operation of display modes up to 4K@60Hz.
It's worth noting that anything above 4K@30Hz still requires high TMDS
clock ratio and scrambling support, which hasn't been mainlined yet.
arm64: dts: rockchip: Enable HDMI PHY clk provider on rk3576
As with the RK3588 SoC, the HDMI PHY PLL on RK3576 can be used as a more
accurate pixel clock source for VOP2, which is actually mandatory to
ensure proper support for display modes handling.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI PHY.
Hsun Lai [Mon, 9 Jun 2025 11:30:44 +0000 (19:30 +0800)]
arm64: dts: rockchip: add DTs for Firefly ROC-RK3588S-PC
The Firefly ROC-RK3588S-PC is a SBC based on the Rockchip RK3588s SoC.
Link: https://wiki.t-firefly.com/en/Station-M3/index.html
The device contains the following hardware that is tested/working:
- 32 or 64GB eMMC
- SDMMC card slot
- Realtek USB WiFi 5/BT
- NVME 2242 socket
- 4 or 8GB of RAM
- RTL8211 GbE
- USB 3.0 port
- USB 2.0 port
- HDMI port
Quentin Schulz [Tue, 10 Jun 2025 16:22:18 +0000 (18:22 +0200)]
arm64: dts: rockchip: support camera module on Haikou Video Demo on PX30 Ringneck
The Haikou Video Demo adapter has a proprietary connector for a camera
module which has an OV5675 camera sensor and a companion DW9714 focus
lens driver.
This adds support for the camera module on PX30 Ringneck module fitted
on a Haikou devkit with the Haikou Video Demo adapter.
Quentin Schulz [Tue, 10 Jun 2025 16:22:17 +0000 (18:22 +0200)]
arm64: dts: rockchip: add label to first port of ISP on px30
This will make it slightly easier for Device Trees (and Overlays) to
link the ISP controller to a video input such as a CSI camera while also
bringing it closer to what's been done already for the DSI controller.
Quentin Schulz [Tue, 10 Jun 2025 16:22:16 +0000 (18:22 +0200)]
arm64: dts: rockchip: fix endpoint dtc warning for PX30 ISP
dtc complains with the following message for DTSes which use the ISP:
arch/arm64/boot/dts/rockchip/px30.dtsi:1272.19-1276.6: Warning (graph_child_address): /isp@ff4a0000/ports/port@0: graph node has single child node 'endpoint@0', #address-cells/#size-cells are not necessary
Typically, it is expected from the device DTS(I) to update the SoC DTSI
nodes if they have more than one endpoint, so let's assume there's only
one endpoint in port@0 by default, instead of forcing board DTS(I)s to
/delete-property/ address-cells and size-cells to make dtc happy.
Because PX30 PP1516/EVB's endpoint@0 is the only endpoint and
considering its parent node now has no address-cells property, dtc
complains (same messages for PX30 EVB):
arch/arm64/boot/dts/rockchip/px30-pp1516.dtsi:447.29-451.6: Warning (avoid_default_addr_size): /isp@ff4a0000/ports/port@0/endpoint@0: Relying on default #address-cells value
arch/arm64/boot/dts/rockchip/px30-pp1516.dtsi:447.29-451.6: Warning (avoid_default_addr_size): /isp@ff4a0000/ports/port@0/endpoint@0: Relying on default #size-cells value
arch/arm64/boot/dts/rockchip/px30-pp1516-ltk050h3146w-a2.dtb: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
arch/arm64/boot/dts/rockchip/px30-pp1516-ltk050h3146w-a2.dtb: Warning (unique_unit_address_if_enabled): Failed prerequisite 'avoid_default_addr_size'
arch/arm64/boot/dts/rockchip/px30-pp1516.dtsi:447.29-451.6: Warning (graph_endpoint): /isp@ff4a0000/ports/port@0/endpoint@0: graph node '#address-cells' is -1, must be 1
arch/arm64/boot/dts/rockchip/px30-pp1516.dtsi:447.29-451.6: Warning (graph_endpoint): /isp@ff4a0000/ports/port@0/endpoint@0: graph node '#size-cells' is -1, must be 0
arch/arm64/boot/dts/rockchip/px30-pp1516-ltk050h3146w-a2.dtb: Warning (graph_child_address): Failed prerequisite 'graph_endpoint'
so we fix that by removing the reg property. dtc still complains (same
messages for PX30 EVB):
arch/arm64/boot/dts/rockchip/px30-pp1516.dtsi:447.29-450.6: Warning (unit_address_vs_reg): /isp@ff4a0000/ports/port@0/endpoint@0: node has a unit name, but no reg or ranges property
so we also remove the @0 suffix off the node name.
Fixes: 8df7b4537dfb ("arm64: dts: rockchip: add isp node for px30") Fixes: 474a77395be2 ("arm64: dts: rockchip: hook up camera on px30-evb") Fixes: 56198acdbf0d ("arm64: dts: rockchip: add px30-pp1516 base dtsi and board variants") Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de> Link: https://lore.kernel.org/r/20250610-ringneck-haikou-video-demo-cam-v2-1-de1bf87e0732@cherry.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ArmSoM Sige5 has several USB ports: a Type-A USB 3 port (USB2 lines
going through a hub), a Type-A USB 2.0 port (also going through a hub),
a Type-C DC input port that has absolutely no USB data connection and a
Type-C port with USB3.2 Gen1x1 that's also the maskrom programming port.
Enable these ports, and set the device role to be host for the host
ports.
The data capable Type-C USB port uses a fusb302 for data role switching.
Alexey Charkov [Sat, 14 Jun 2025 18:14:36 +0000 (22:14 +0400)]
arm64: dts: rockchip: add overlay for the WiFi/BT module on Sige5 v1.2
Add support for the Broadcom based WiFi/Bluetooth module (BW3752-50B1)
found in ArmSoM Sige5 boards version 1.2. This includes SDIO connected
WiFi with OOB interrupt support, as well as UART connected Bluetooth
with its respective interrupts.
PCM support for Bluetooth SCO audio is left out for now. It is connected
to SAI2 in M0 pin mode in case someone needs to enable it.
Note that v1.1 boards used a Realtek based module which is incompatible
with these DT nodes, so v1.1 would need a different overlay.
Alexey Charkov [Sat, 14 Jun 2025 18:14:35 +0000 (22:14 +0400)]
arm64: dts: rockchip: add version-independent WiFi/BT nodes on Sige5
ArmSoM Sige5 uses a soldered-on WiFi/BT module with WiFi on SDIO and BT
on UART. However, board v1.1 uses a Realtek based BL-M8852BS2, while
v1.2 uses a Broadcom based BW3752-50B1. They use the same pins and
controllers, but require different DT properties to enable.
Thankfully, the WiFi part at least works without explicitly listing it in
the device tree, albeit without OOB interrupt functionality.
Add required device tree nodes that do not depend on the board version so
that at least the WiFi module can appear on the SDIO bus.
WiFi OOB interrupt and Bluetooth function support are not enabled here, as
they require module specific properties.
Alexey Charkov [Sat, 14 Jun 2025 18:14:34 +0000 (22:14 +0400)]
arm64: dts: rockchip: add SDIO controller on RK3576
RK3576 has one more SD/MMC controller than are currently listed in its
.dtsi, with the missing one intended as an SDIO controller. Add the
missing node (tested with the onboard WiFi module on ArmSoM Sige5 v1.2)
Olivier Benjamin [Thu, 19 Jun 2025 13:41:24 +0000 (15:41 +0200)]
arm64: dts: rockchip: Update the PinePhone Pro panel description
Fix a few issues in the panel section of the PinePhone Pro DTS:
- add the second part of the Himax HX8394 LCD panel controller
compatible
- as proposed by Diederik de Haas, reuse the mipi_out and ports
definitions from rk3399-base.dtsi instead of redefining them
- add a pinctrl for the LCD_RST signal for LCD1, derived from
LCD1_RST, which is on GPIO4_D1, as documented on pages 11
and 16 of the PinePhone Pro schematic
John Clark [Fri, 16 May 2025 00:27:13 +0000 (20:27 -0400)]
arm64: dts: rockchip: Add Luckfox Omni3576 Board support
Add device tree for the Luckfox Omni3576 Carrier Board with Core3576
Module, powered by the Rockchip RK3576 SoC with four Cortex-A72 cores,
four Cortex-A53 cores, and a Mali-G52 MC3 GPU. This initial
implementation enables essential functionality for booting Linux and
basic connectivity.
Supported and tested features:
- UART for serial console
- SD card for storage
- PCIe with NVMe SSD (detected, mounted, and fully functional)
- USB 2.0 host ports
- RK806 PMIC for power management
- RTC with timekeeping and wake-up
- GPIO-controlled LED with heartbeat trigger
- eMMC (enabled, not populated on tested board)
The device tree provides a foundation for further peripheral support, such
as WiFi, MIPI-DSI, HDMI, and Ethernet, in future updates.
Tested on Linux 6.15-rc4
Based on the Luckfox SDK, which derives from Rockchip’s SDK examples, with
relevant changes to align with upstream Linux.
Sam Edwards [Sun, 8 Jun 2025 18:48:55 +0000 (11:48 -0700)]
arm64: dts: rockchip: Remove workaround that prevented Turing RK1 GPU power regulator control
The RK3588 GPU power domain cannot be activated unless the external
power regulator is already on. When GPU support was added to this DT,
we had no way to represent this requirement, so `regulator-always-on`
was added to the `vdd_gpu_s0` regulator in order to ensure stability.
A later patch series (see "Fixes:" commit) resolved this shortcoming,
but that commit left the workaround -- and rendered the comment above
it no longer correct.
Remove the workaround to allow the GPU power regulator to power off, now
that the DT includes the necessary information to power it back on
correctly.
Fixes: f94500eb7328b ("arm64: dts: rockchip: Add GPU power domain regulator dependency for RK3588") Signed-off-by: Sam Edwards <CFSworks@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250608184855.130206-1-CFSworks@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter Robinson [Sun, 18 May 2025 21:59:34 +0000 (22:59 +0100)]
arm64: dts: rockchip: add overlay for RockPro64 screen
The Pine64 touch panel is a panel consisting of the Feiyang fy07024di26a30d
panel with a Goodix gt911 touch screen. Add a device tree overlay to
allow the display to be easily used on the device.
This was previously included in the main device tree but left disabled
by default which still required rebuilding the DT to use the device, now
overlays can go upstream the overlay is the best way to handle the
add on devices.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
[added the missing v2 to
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64-v2-screen.dtb
^^
rk3399-rockpro64-v2-screen-dtbs := rk3399-rockpro64-v2.dtb \
rk3399-rockpro64-screen.dtbo
dropped address-cells/size-cells from panel node to fix warning about
rk3399-rockpro64-screen.dtso:69.22-84.4: Warning (avoid_unnecessary_addr_size)
/fragment@2/__overlay__/panel@0: unnecessary #address-cells/#size-cells
without "ranges", "dma-ranges" or child "reg" property] Link: https://lore.kernel.org/r/20250518215944.178582-2-pbrobinson@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter Robinson [Sun, 18 May 2025 21:59:33 +0000 (22:59 +0100)]
arm64: dts: rockchip: drop touch panel display from rockpro64
The touch panel display is an optional add on for the RockPro64
so this should be an DT overlay, drop the panel options in
preparation to add this as an overlay.
This effectively reverts commit b65155c786c4 so as to add an
overlay for it.
John Clark [Tue, 20 May 2025 00:33:32 +0000 (20:33 -0400)]
arm64: dts: rockchip: Use standard PHY reset properties for RK3576 ArmSoM Sige5
Replace deprecated snps,reset-gpio, snps,reset-active-low, and
snps,reset-delays-us in gmac0 and gmac1 nodes with standard reset-gpios,
reset-assert-us, and reset-deassert-us in rgmii_phy0 and rgmii_phy1 nodes.
Add pinctrl properties to PHY nodes and define gmac0_rst and gmac1_rst in
pinctrl node. Reorder phy-handle for consistency.
The RADXA ROCK 5T is a single board computer quite similar to the ROCK
5B+, except it has one more PCIe-to-Ethernet controller (at the expense
of a USB3 port) and a barrel jack for power input instead. Some pins are
shuffled around as well.
The RADXA ROCK 5T is a single board computer aimed at industrial use.
Its design is similar to the ROCK 5B+, but it does away with one of the
USB-C PD inputs, and uses one combination USB3/SATA/PCIe PHY for an
additional second 2.5G PCIe network card instead of USB3.
Diederik de Haas [Mon, 26 May 2025 16:14:47 +0000 (18:14 +0200)]
arm64: dts: rockchip: Fix cover detection on PineNote
The SW_MACHINE_COVER switch event was added to input event codes to
detect the removal of the back cover of the N900.
But on the PineNote its purpose is to detect when the front cover gets
closed, just like when a laptop lid is closed. Therefore SW_LID is the
appropriate linux code and not SW_MACHINE_COVER.
Chris Morgan [Wed, 4 Jun 2025 02:41:19 +0000 (21:41 -0500)]
arm64: dts: rockchip: Document unused device on i2c1
Update the i2c1 bus noting that the unknown/unused device at 0x3c is an
iSmartWare SW2001 "encryption IC".
Based on the documentation I was able to find, this IC appears to be
used to authenticate a device for certain programs to ensure they only
run on authorized devices as a form of digital rights management.
Quentin Schulz [Wed, 4 Jun 2025 16:18:08 +0000 (18:18 +0200)]
arm64: dts: rockchip: support Ethernet Switch adapter for RK3588 Jaguar
This adds support for the Ethernet Switch adapter connected to the
mezzanine connector on RK3588 Jaguar.
This adapter has a KSZ9896 Ethernet Switch with 4 1GbE Ethernet
connectors, two user controllable LEDs, and an M12 12-pin connector
which exposes the following signals:
- RS232/RS485 (max 250Kbps/500Kbps, RX pin1, TX pin2)
- two digital inputs (pin4 routed to GPIO3_C5 on SoC, pin5 to GPIO4_B4)
- two digital outputs (pin7 routed to GPIO3_D3 on SoC, pin8 to
GPIO3_D1)
- two analog inputs (pin10 to channel1 of ADS1015, pin11 to channel2)
Chris Morgan [Tue, 3 Jun 2025 19:39:30 +0000 (14:39 -0500)]
arm64: dts: rockchip: Add DSI panel support for gameforce-ace
Enable the DSI controller, DSI DCPHY, and Huiling hl055fhav028c
1080x1920 panel for the Gameforce Ace.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://lore.kernel.org/r/20250603193930.323607-5-macroalpha82@gmail.com
[moved lcd_rst pin into a lcd pinctrl group with lcd_bl_en] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linus Torvalds [Sun, 8 Jun 2025 18:33:00 +0000 (11:33 -0700)]
Merge tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Linus Torvalds [Sun, 8 Jun 2025 18:27:20 +0000 (11:27 -0700)]
Merge tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Zhang Rui [Fri, 30 May 2025 00:09:28 +0000 (08:09 +0800)]
tools/power turbostat: Avoid probing the same perf counters
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:44:50 +0000 (17:44 +0800)]
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
commit 05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db888 ("tools/power turbostat: read RAPL counters via perf") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: Add Android support for MSR device handling
It uses /dev/msrN device paths on Android instead of /dev/cpu/N/msr,
updates error messages and permission checks to reflect the Android
device path, and wraps platform-specific code with #if defined(ANDROID)
to ensure correct behavior on both Android and non-Android systems.
These changes improve compatibility and usability of turbostat on
Android devices.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sun, 8 Jun 2025 18:07:33 +0000 (11:07 -0700)]
Merge tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf fix from Thomas Gleixner:
"A single fix for the x86 performance counters on Intel CPUs:
The MSR offset calculations for fixed performance counters are stored
at the wrong index in the configuration array causing the general
purpose counter MSR offset to be overwritten, so both the general
purpose and the fixed counters offsets are incorrect.
Correct the array index calculation to fix that"
* tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix incorrect MSR index calculations in intel_pmu_config_acr()
Linus Torvalds [Sun, 8 Jun 2025 18:02:53 +0000 (11:02 -0700)]
Merge tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for the PCI/MSI code:
The conversion to per device MSI domains created a MSI domain with
size 1 instead of sizing it to the maximum possible number of MSI
interrupts for the device. This "worked" as the subsequent allocations
resized the domain, but the recent change to move the prepare() call
into the domain creation path broke this works by chance mechanism.
Size the domain properly at creation time"
* tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Size device MSI domain with the maximum number of vectors
Linus Torvalds [Sun, 8 Jun 2025 17:35:12 +0000 (10:35 -0700)]
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount fixes from Al Viro:
"Various mount-related bugfixes:
- split the do_move_mount() checks in subtree-of-our-ns and
entire-anon cases and adapt detached mount propagation selftest for
mount_setattr
- allow clone_private_mount() for a path on real rootfs
- fix a race in call of has_locked_children()
- fix move_mount propagation graph breakage by MOVE_MOUNT_SET_GROUP
- make sure clone_private_mnt() caller has CAP_SYS_ADMIN in the right
userns
- avoid false negatives in path_overmount()
- don't leak MNT_LOCKED from parent to child in finish_automount()
- do_change_type(): refuse to operate on unmounted/not ours mounts"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_change_type(): refuse to operate on unmounted/not ours mounts
clone_private_mnt(): make sure that caller has CAP_SYS_ADMIN in the right userns
selftests/mount_setattr: adapt detached mount propagation test
do_move_mount(): split the checks in subtree-of-our-ns and entire-anon cases
fs: allow clone_private_mount() for a path on real rootfs
fix propagation graph breakage by MOVE_MOUNT_SET_GROUP move_mount(2)
finish_automount(): don't leak MNT_LOCKED from parent to child
path_overmount(): avoid false negatives
fs/fhandle.c: fix a race in call of has_locked_children()
Linus Torvalds [Sun, 8 Jun 2025 17:20:21 +0000 (10:20 -0700)]
Merge tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- multichannel/reconnect fixes
- move smbdirect (smb over RDMA) defines to fs/smb/common so they will
be able to be used in the future more broadly, and a documentation
update explaining setting up smbdirect mounts
- update email address for Paulo
* tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
MAINTAINERS, mailmap: Update Paulo Alcantara's email address
cifs: add documentation for smbdirect setup
cifs: do not disable interface polling on failure
cifs: serialize other channels when query server interfaces is pending
cifs: deal with the channel loading lag while picking channels
smb: client: make use of common smbdirect_socket_parameters
smb: smbdirect: introduce smbdirect_socket_parameters
smb: client: make use of common smbdirect_socket
smb: smbdirect: add smbdirect_socket.h
smb: client: make use of common smbdirect.h
smb: smbdirect: add smbdirect.h with public structures
smb: client: make use of common smbdirect_pdu.h
smb: smbdirect: add smbdirect_pdu.h with protocol definitions
Linus Torvalds [Sun, 8 Jun 2025 15:19:01 +0000 (08:19 -0700)]
Merge tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull more tracing fixes from Steven Rostedt:
- Fix regression of waiting a long time on updating trace event filters
When the faultable trace points were added, it needed task trace RCU
synchronization.
This was added to the tracepoint_synchronize_unregister() function.
The filter logic always called this function whenever it updated the
trace event filters before freeing the old filters. This increased
the time of "trace-cmd record" from taking 13 seconds to running over
2 minutes to complete.
Move the freeing of the filters to call_rcu*() logic, which brings
the time back down to 13 seconds.
The error path of the ring_buffer_subbuf_order_set() released the
mutex too early and allowed subsequent accesses to setting the
subbuffer size to corrupt the data and cause a bug.
By moving the mutex locking to the end of the error path, it prevents
the reentrant access to the critical data and also allows the
function to convert the taking of the mutex over to the guard()
logic.
- Remove unused power management clock events
The clock events were added in 2010 for power management. In 2011 arm
used them. In 2013 the code they were used in was removed. These
events have been wasting memory since then.
- Fix sparse warnings
There was a few places that sparse warned about trace_events_filter.c
where file->filter was referenced directly, but it is annotated with
an __rcu tag. Use the helper functions and fix them up to use
rcu_dereference() properly.
* tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Add rcu annotation around file->filter accesses
tracing: PM: Remove unused clock events
ring-buffer: Fix buffer locking in ring_buffer_subbuf_order_set()
tracing: Fix regression of filter waiting a long time on RCU synchronization
Linus Torvalds [Sat, 7 Jun 2025 17:05:35 +0000 (10:05 -0700)]
Merge tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add support for the EXPORT_SYMBOL_GPL_FOR_MODULES() macro, which
exports a symbol only to specified modules
- Improve ABI handling in gendwarfksyms
- Forcibly link lib-y objects to vmlinux even if CONFIG_MODULES=n
- Add checkers for redundant or missing <linux/export.h> inclusion
- Deprecate the extra-y syntax
- Fix a genksyms bug when including enum constants from *.symref files
* tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (28 commits)
genksyms: Fix enum consts from a reference affecting new values
arch: use always-$(KBUILD_BUILTIN) for vmlinux.lds
kbuild: set y instead of 1 to KBUILD_{BUILTIN,MODULES}
efi/libstub: use 'targets' instead of extra-y in Makefile
module: make __mod_device_table__* symbols static
scripts/misc-check: check unnecessary #include <linux/export.h> when W=1
scripts/misc-check: check missing #include <linux/export.h> when W=1
scripts/misc-check: add double-quotes to satisfy shellcheck
kbuild: move W=1 check for scripts/misc-check to top-level Makefile
scripts/tags.sh: allow to use alternative ctags implementation
kconfig: introduce menu type enum
docs: symbol-namespaces: fix reST warning with literal block
kbuild: link lib-y objects to vmlinux forcibly even when CONFIG_MODULES=n
tinyconfig: enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION
docs/core-api/symbol-namespaces: drop table of contents and section numbering
modpost: check forbidden MODULE_IMPORT_NS("module:") at compile time
kbuild: move kbuild syntax processing to scripts/Makefile.build
Makefile: remove dependency on archscripts for header installation
Documentation/kbuild: Add new gendwarfksyms kABI rules
Documentation/kbuild: Drop section numbers
...
Linus Torvalds [Sat, 7 Jun 2025 17:00:03 +0000 (10:00 -0700)]
Merge tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
- replace the __ASSEMBLY__ with __ASSEMBLER__ macro in all headers
since the latter is now defined automatically by both GCC and Clang
when compiling assembly code (Thomas Huth)
- set the default SPI mode for the ecovec24 board which became
necessary after a new mode member as added to the sh_msiof_spi_info
struct in cf9e4784f3bd ("spi: sh-msiof: Add slave mode support")
(Geert Uytterhoeven)
- remove unused variables in the kprobes code in
kprobe_exceptions_notify() (Mike Rapoport)
* tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
sh: ecovec24: Make SPI mode explicit
sh: Replace __ASSEMBLY__ with __ASSEMBLER__ in all headers
Linus Torvalds [Sat, 7 Jun 2025 16:56:18 +0000 (09:56 -0700)]
Merge tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Adjust the 'make install' operation
- Support SCHED_MC (Multi-core scheduler)
- Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
- Enable HAVE_ARCH_STACKLEAK
- Increase max supported CPUs up to 2048
- Introduce the numa_memblks conversion
- Add PWM controller nodes in dts
- Some bug fixes and other small changes
* tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
platform/loongarch: laptop: Unregister generic_sub_drivers on exit
platform/loongarch: laptop: Add backlight power control support
platform/loongarch: laptop: Get brightness setting from EC on probe
LoongArch: dts: Add PWM support to Loongson-2K2000
LoongArch: dts: Add PWM support to Loongson-2K1000
LoongArch: dts: Add PWM support to Loongson-2K0500
LoongArch: vDSO: Correctly use asm parameters in syscall wrappers
LoongArch: Fix panic caused by NULL-PMD in huge_pte_offset()
LoongArch: Preserve firmware configuration when desired
LoongArch: Avoid using $r0/$r1 as "mask" for csrxchg
LoongArch: Introduce the numa_memblks conversion
LoongArch: Increase max supported CPUs up to 2048
LoongArch: Enable HAVE_ARCH_STACKLEAK
LoongArch: Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
LoongArch: Add SCHED_MC (Multi-core scheduler) support
LoongArch: Add some annotations in archhelp
LoongArch: Using generic scripts/install.sh in `make install`
LoongArch: Add a default install.sh
Linus Torvalds [Sat, 7 Jun 2025 16:40:08 +0000 (09:40 -0700)]
Merge tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fix patches for the 6.16-rc1 merge window.
Most of changes are about ASoC, especially lots of AVS driver fixes.
Larger LOCs are seen in TAS571x codec drivers, but the changes are
trivial and safe. The rest are all device-specific small fixes"
* tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ASoC: Intel: avs: boards: Fix rt5663 front end name
ASoC: Intel: avs: Simplify verification of parse_int_array() result
ALSA: usb-audio: Add implicit feedback quirk for RODE AI-1
ALSA: hda: Ignore unsol events for cards being shut down
ALSA: hda: Add new pci id for AMD GPU display HD audio controller
ALSA: hda: cs35l41: Constify regmap_irq_chip
ALSA: usb-audio: Add a quirk for Lenovo Thinkpad Thunderbolt 3 dock
ASoC: ti: omap-hdmi: Re-add dai_link->platform to fix card init
ASoC: pcm: Do not open FEs with no BEs connected
ASoC: rt1320: fix speaker noise when volume bar is 100%
ASoC: Intel: avs: Include missing string.h
ASoC: Intel: avs: Verify content returned by parse_int_array()
ASoC: Intel: avs: Verify kcalloc() status when setting constraints
ASoC: Intel: avs: Fix paths in MODULE_FIRMWARE hints
ASoC: Intel: avs: Fix possible null-ptr-deref when initing hw
ASoC: Intel: avs: Fix PPLCxFMT calculation
ASoC: Intel: avs: Fix deadlock when the failing IPC is SET_D0IX
ASoC: codecs: hda: Fix RPM usage count underflow
ASoC: amd: yc: Add support for Lenovo Yoga 7 16ARP8
ASoC: tas571x: fix tas5733 num_controls
...
Linus Torvalds [Sat, 7 Jun 2025 14:24:07 +0000 (07:24 -0700)]
Merge tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2 and UBIFS fixes from Richard Weinberger:
"JFFS2:
- Correctly check return code of jffs2_prealloc_raw_node_refs()
UBIFS:
- Spelling fixes"
* tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: check jffs2_prealloc_raw_node_refs() result in few other places
jffs2: check that raw node were preallocated before writing summary
ubifs: Fix grammar in error message
Mike Rapoport [Sat, 17 May 2025 09:30:48 +0000 (12:30 +0300)]
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
kbuild reports the following warning:
arch/sh/kernel/kprobes.c: In function 'kprobe_exceptions_notify':
>> arch/sh/kernel/kprobes.c:412:24: warning: variable 'p' set but not used [-Wunused-but-set-variable]
412 | struct kprobe *p = NULL;
| ^
The variable 'p' is indeed unused since the commit fa5a24b16f94
("sh/kprobes: Don't call the ->break_handler() in SH kprobes code")
Remove that variable along with 'kprobe_opcode_t *addr' which also
becomes unused after 'p' is removed.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202505151341.EuRFR22l-lkp@intel.com/ Fixes: fa5a24b16f94 ("sh/kprobes: Don't call the ->break_handler() in SH kprobes code") Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Commit cf9e4784f3bde3e4 ("spi: sh-msiof: Add slave mode support") added
a new mode member to the sh_msiof_spi_info structure, but did not update
any board files. Hence all users in board files rely on the default
being host mode.
Make this unambiguous by configuring host mode explicitly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Thomas Huth [Fri, 14 Mar 2025 07:10:03 +0000 (08:10 +0100)]
sh: Replace __ASSEMBLY__ with __ASSEMBLER__ in all headers
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembly code, __ASSEMBLY__ is a
macro that only gets defined by the Makefiles in the kernel.
This can be very confusing when switching between userspace
and kernelspace coding, or when dealing with uapi headers that
rather should use __ASSEMBLER__ instead. So let's standardize on
the __ASSEMBLER__ macro that is provided by the compilers now.
This is a completely mechanical patch (done with a simple "sed -i"
statement).
Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Cc: linux-sh@vger.kernel.org Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
$ cat test.0.symtypes
E#E_MAX 2
s#bar struct bar { int mem [ E#E_MAX ] ; }
foo int foo ( s#bar * )
$ cat test.c | ./scripts/genksyms/genksyms -T test.1.symtypes -r test.0.symtypes
<stdin>:4: warning: foo: modversion changed because of changes in enum constant E_MAX
#SYMVER foo 0x9c9dfd81
$ cat test.1.symtypes
E#E_MAX ( 2 ) + 3
s#bar struct bar { int mem [ E#E_MAX ] ; }
foo int foo ( s#bar * )
The __add_symbol() function includes logic to handle the incrementation of
enumeration values, but this code is also invoked when reading a reference
file. As a result, the variables last_enum_expr and enum_counter might be
incorrectly set after reading the reference file, which later affects
parsing of the actual input.
Fix the problem by splitting the logic for the incrementation of
enumeration values into a separate function process_enum() and call it from
__add_symbol() only when processing non-reference data.
Fixes: e37ddb825003 ("genksyms: Track changes to enum constants") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Al Viro [Wed, 4 Jun 2025 16:27:08 +0000 (12:27 -0400)]
do_change_type(): refuse to operate on unmounted/not ours mounts
Ensure that propagation settings can only be changed for mounts located
in the caller's mount namespace. This change aligns permission checking
with the rest of mount(2).
Reviewed-by: Christian Brauner <brauner@kernel.org> Fixes: 07b20889e305 ("beginning of the shared-subtree proper") Reported-by: "Orlando, Noah" <Noah.Orlando@deshaw.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 2 Jun 2025 00:11:06 +0000 (20:11 -0400)]
clone_private_mnt(): make sure that caller has CAP_SYS_ADMIN in the right userns
What we want is to verify there is that clone won't expose something
hidden by a mount we wouldn't be able to undo. "Wouldn't be able to undo"
may be a result of MNT_LOCKED on a child, but it may also come from
lacking admin rights in the userns of the namespace mount belongs to.
clone_private_mnt() checks the former, but not the latter.
There's a number of rather confusing CAP_SYS_ADMIN checks in various
userns during the mount, especially with the new mount API; they serve
different purposes and in case of clone_private_mnt() they usually,
but not always end up covering the missing check mentioned above.
Reviewed-by: Christian Brauner <brauner@kernel.org> Reported-by: "Orlando, Noah" <Noah.Orlando@deshaw.com> Fixes: 427215d85e8d ("ovl: prevent private clone if bind mount is not allowed") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 7 Jun 2025 05:06:57 +0000 (22:06 -0700)]
Merge tag 'mm-stable-2025-06-06-16-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more MM updates from Andrew Morton:
"The series 'Fix uprobe pte be overwritten when expanding vma' fixes a
longstanding and quite obscure bug related to the vma merging of the
uprobe mmap page"
* tag 'mm-stable-2025-06-06-16-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
selftests/mm: add test about uprobe pte be orphan during vma merge
selftests/mm: extract read_sysfs and write_sysfs into vm_util
mm: expose abnormal new_pte during move_ptes
mm: fix uprobe pte be overwritten when expanding vma
mm/damon: s/primitives/code/ on comments
Linus Torvalds [Sat, 7 Jun 2025 04:45:45 +0000 (21:45 -0700)]
Merge tag 'mm-hotfixes-stable-2025-06-06-16-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"13 hotfixes.
6 are cc:stable and the remainder address post-6.15 issues or aren't
considered necessary for -stable kernels. 11 are for MM"
* tag 'mm-hotfixes-stable-2025-06-06-16-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kernel/rcu/tree_stall: add /sys/kernel/rcu_stall_count
MAINTAINERS: add mm swap section
kmsan: test: add module description
MAINTAINERS: add tlb trace events to MMU GATHER AND TLB INVALIDATION
mm/hugetlb: fix huge_pmd_unshare() vs GUP-fast race
mm/hugetlb: unshare page tables during VMA split, not before
MAINTAINERS: add Alistair as reviewer of mm memory policy
iov_iter: use iov_offset for length calculation in iov_iter_aligned_bvec
mm/mempolicy: fix incorrect freeing of wi_kobj
alloc_tag: handle module codetag load errors as module load failures
mm/madvise: handle madvise_lock() failure during race unwinding
mm: fix vmstat after removing NR_BOUNCE
KVM: s390: rename PROT_NONE to PROT_TYPE_DUMMY
projects / thirdparty / linux.git / log
