A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b090 ("[media] s5p-fimc: Add the media device driver") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbce5 ("[media] solo6x10: sync to latest code from Bluecherry's git repo") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The input parameter @fields is type of struct ima_template_field ***, so
when allocates array memory for @fields, the size of element should be
sizeof(**field) instead of sizeof(*field).
Actually the original code would not cause any runtime error, but it's
better to make it logically right.
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e6d ("regulator: map consumer regulator based on device tree") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because we forget to check boundary after adjust compose->height
int V4L2_SEL_TGT_CROP case. Add v4l2_rect_map_inside() to fix this problem
for this case.
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible that skb is freed in ath9k_htc_rx_msg(), then
usb_submit_urb() fails and we try to free skb again. It causes
use-after-free bug. Moreover, if alloc_skb() fails, urb->context becomes
NULL but rx_buf is not freed and there can be a memory leak.
The patch removes unnecessary nskb and makes skb processing more clear: it
is supposed that ath9k_htc_rx_msg() either frees old skb or passes its
managing to another callback function.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 03fb92a432ea ("ath9k: hif_usb: fix race condition between usb_get_urb() and usb_kill_anchored_urbs()") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220725151359.283704-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
When kfifo_alloc fails, the refcount of chdev->dev is left incremental.
We should use put_device(&chdev->dev) to decrease the ref count of
chdev->dev to avoid refcount leak.
Link: https://lkml.kernel.org/r/20221203085721.13146-1-caixinchen1@huawei.com Fixes: e8de370188d0 ("rapidio: add mport char device driver") Signed-off-by: Cai Xinchen <caixinchen1@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Wang Weiyang <wangweiyang2@huawei.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
loop0: detected capacity change from 0 to 64
==================================================================
BUG: KASAN: slab-out-of-bounds in hfs_asc2mac+0x467/0x9a0
fs/hfs/trans.c:133
Write of size 1 at addr ffff88801848314e by task syz-executor391/3632
If in->len is much larger than HFS_NAMELEN(31) which is the maximum
length of an HFS filename, a OOB write could occur in hfs_asc2mac(). In
that case, when the dst reaches the boundary, the srclen is still
greater than 0, which causes a OOB write.
Fix this by adding a check on dstlen in while() before writing to dst
address.
If kfifo_alloc() fails in mport_cdev_open(), goto err_fifo and just free
priv. But priv is still in the chdev->file_list, then list traversal
may cause UAF. This fixes the following smatch warning:
drivers/rapidio/devices/rio_mport_cdev.c:1930 mport_cdev_open() warn: '&priv->list' not removed from list
Link: https://lkml.kernel.org/r/20221123095147.52408-1-wangweiyang2@huawei.com Fixes: e8de370188d0 ("rapidio: add mport char device driver") Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sysv_nblocks() returns 'blocks' rather than 'res', which only counting
the number of triple-indirect blocks and causing sysv_getattr() gets a
wrong result.
[AV: this is actually a sysv counterpart of minixfs fix - 0fcd426de9d0 "[PATCH] minix block usage counting fix" in
historical tree; mea culpa, should've thought to check
fs/sysv back then...]
Check clk for NULL before calling clk_enable_unlocked where clk
is dereferenced. There is such check in other implementations
of clk_enable.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.") Signed-off-by: Anastasia Belova <abelova@astralinux.ru> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In xen_init_lock_cpu(), the @name has allocated new string by kasprintf(),
if bind_ipi_to_irqhandler() fails, it should be freed, otherwise may lead
to a memory leak issue, fix it.
Intel ICC -hotpatch inserts 2-byte "0x66 0x90" NOP at the start of each
function to reserve extra space for hot-patching, and currently it is not
possible to probe these functions because branch_setup_xol_ops() wrongly
rejects NOP with REP prefix as it treats them like word-sized branch
instructions.
BUG: KASAN: use-after-free in acpi_ut_remove_reference+0x3b/0x82
Read of size 1 at addr ffff888112afc460 by task modprobe/2111
CPU: 0 PID: 2111 Comm: modprobe Not tainted 6.1.0-rc7-dirty
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
Call Trace:
<TASK>
kasan_report+0xae/0xe0
acpi_ut_remove_reference+0x3b/0x82
acpi_ut_copy_iobject_to_iobject+0x3be/0x3d5
acpi_ds_store_object_to_local+0x15d/0x3a0
acpi_ex_store+0x78d/0x7fd
acpi_ex_opcode_1A_1T_1R+0xbe4/0xf9b
acpi_ps_parse_aml+0x217/0x8d5
...
</TASK>
The root cause of the problem is that the acpi_operand_object
is freed when acpi_ut_walk_package_tree() fails in
acpi_ut_copy_ipackage_to_ipackage(), lead to repeated release in
acpi_ut_copy_iobject_to_iobject(). The problem was introduced
by "8aa5e56eeb61" commit, this commit is to fix memory leak in
acpi_ut_copy_iobject_to_iobject(), repeatedly adding remove
operation, lead to "acpi_operand_object" used after free.
Fix it by removing acpi_ut_remove_reference() in
acpi_ut_copy_ipackage_to_ipackage(). acpi_ut_copy_ipackage_to_ipackage()
is called to copy an internal package object into another internal
package object, when it fails, the memory of acpi_operand_object
should be freed by the caller.
Fixes: 8aa5e56eeb61 ("ACPICA: Utilities: Fix memory leak in acpi_ut_copy_iobject_to_iobject") Signed-off-by: Li Zetao <lizetao1@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error, the name allocated by dev_set_name()
need be freed. It should use put_device() to give up the reference in the
error path, so that the name can be freed in kobject_cleanup(), and
list_del() is called to delete the port from rio_mports.
Link: https://lkml.kernel.org/r/20221114152636.2939035-3-yangyingliang@huawei.com Fixes: 2aaf308b95b2 ("rapidio: rework device hierarchy and introduce mport class of devices") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "rapidio: fix three possible memory leaks".
This patchset fixes three name leaks in error handling.
- patch #1 fixes two name leaks while rio_add_device() fails.
- patch #2 fixes a name leak while rio_register_mport() fails.
This patch (of 2):
If rio_add_device() returns error, the name allocated by dev_set_name()
need be freed. It should use put_device() to give up the reference in the
error path, so that the name can be freed in kobject_cleanup(), and the
'rdev' can be freed in rio_release_dev().
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()").
This restores the previous behaviour by using newly introduced
DEFINE_SIMPLE_ATTRIBUTE_SIGNED instead of DEFINE_SIMPLE_ATTRIBUTE.
Link: https://lkml.kernel.org/r/20220919172418.45257-3-akinobu.mita@gmail.com Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Oscar Salvador <osalvador@suse.de> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "fix error when writing negative value to simple attribute
files".
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), but some attribute files want to accept a negative
value.
This patch (of 3):
The simple attribute files do not accept a negative value since the commit 488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), so we have to use a 64-bit value to write a
negative value.
This adds DEFINE_SIMPLE_ATTRIBUTE_SIGNED for a signed value.
Link: https://lkml.kernel.org/r/20220919172418.45257-1-akinobu.mita@gmail.com Link: https://lkml.kernel.org/r/20220919172418.45257-2-akinobu.mita@gmail.com Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Oscar Salvador <osalvador@suse.de> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
gic_probe() calls pm_runtime_get_sync() and added fail path as
rpm_put to put usage_counter. However, pm_runtime_get_sync()
will increment usage_counter even it failed. Fix it by replacing it with
pm_runtime_resume_and_get() to keep usage counter balanced.
Fixes: 9c8edddfc992 ("irqchip/gic: Add platform driver for non-root GICs that require RPM") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221124065150.22809-1-shangxiaojing@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
move dev_set_name() after pnp_add_id() to avoid memory leak.
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_set_name() allocates memory for name, it need be freed
when module exiting, call put_device() to give up reference,
so that it can be freed in kobject_cleanup() when the refcount
hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 17a1d523aa58 ("MIPS: APRP: Add VPE loader support for CMP platforms.") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
it need be freed when module exiting, call put_device() to give up
reference, so that it can be freed in kobject_cleanup() when the
refcount hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Link: https://lkml.kernel.org/r/41651ca1-432a-db34-eb97-d35744559de1@linux.alibaba.com Fixes: 3878f110f71a ("ocfs2: Move the hb_ctl_path sysctl into the stack glue.") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When `timerqueue_getnext()` is called on an empty timer queue, it will
use `rb_entry()` on a NULL pointer, which is invalid. Fix that by using
`rb_entry_safe()` which handles NULL pointers.
This has not caused any issues so far because the offset of the `rb_node`
member in `timerqueue_node` is 0, so `rb_entry()` is essentially a no-op.
Fixes: 511885d7061e ("lib/timerqueue: Rely on rbtree semantics for next timer") Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20221114195421.342929-1-pobrn@protonmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In pmu_dev_alloc(), when dev_set_name() failed, it will goto free_dev
and call put_device(pmu->dev) to release it.
However pmu->dev->release is assigned after this, which makes warning
and memleak.
Call dev_set_name() after pmu->dev->release = pmu_dev_release to fix it.
Device '(null)' does not have a release() function...
WARNING: CPU: 2 PID: 441 at drivers/base/core.c:2332 device_release+0x1b9/0x240
...
Call Trace:
<TASK>
kobject_put+0x17f/0x460
put_device+0x20/0x30
pmu_dev_alloc+0x152/0x400
perf_pmu_register+0x96b/0xee0
...
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
unreferenced object 0xffff888014759000 (size 2048):
comm "modprobe", pid 441, jiffies 4294931444 (age 38.332s)
backtrace:
[<0000000005aed3b4>] kmalloc_trace+0x27/0x110
[<000000006b38f9b8>] pmu_dev_alloc+0x50/0x400
[<00000000735f17be>] perf_pmu_register+0x96b/0xee0
[<00000000e38477f1>] 0xffffffffc0ad8603
[<000000004e162216>] do_one_initcall+0xd0/0x4e0
...
The check being unconditional may lead to unwanted denials reported by
LSMs when a process has the capability granted by DAC, but denied by an
LSM. In the case of SELinux such denials are a problem, since they can't
be effectively filtered out via the policy and when not silenced, they
produce noise that may hide a true problem or an attack.
Checking for the capability only if any trusted xattr is actually
present wouldn't really address the issue, since calling listxattr(2) on
such node on its own doesn't indicate an explicit attempt to see the
trusted xattrs. Additionally, it could potentially leak the presence of
trusted xattrs to an unprivileged user if they can check for the denials
(e.g. through dmesg).
Therefore, it's best (and simplest) to keep the check unconditional and
instead use ns_capable_noaudit() that will silence any associated LSM
denials.
Fixes: 38f38657444d ("xattr: extract simple_xattr code from tmpfs") Reported-by: Martin Pitt <mpitt@redhat.com> Suggested-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org> Reviewed-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
but the one in the kerneldoc comment of the function is different and
incorrect.
Fixes: ddeb64870810 ("PM / Hibernate: Add sysfs knob to control size of memory for drivers") Signed-off-by: xiongxin <xiongxin@kylinos.cn>
[ rjw: Subject and changelog rewrite ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We only want to take the slow path if SYSCALL_TRACE or SYSCALL_AUDIT is
set; on !AUDIT_SYSCALL configs the current tree hits it whenever _any_
thread flag (including NEED_RESCHED, NOTIFY_SIGNAL, etc.) happens to
be set.
While we correctly skips to initialize an idle state from a disabled idle
state node in DT, the returned value from dt_init_idle_driver() don't get
adjusted accordingly. Instead the number of found idle state nodes are
returned, while the callers are expecting the number of successfully
initialized idle states from DT.
This leads to cpuidle drivers unnecessarily continues to initialize their
idle state specific data. Moreover, in the case when all idle states have
been disabled in DT, we would end up registering a cpuidle driver, rather
than relying on the default arch specific idle call.
Fixes: 9f14da345599 ("drivers: cpuidle: implement DT based idle states infrastructure") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An oops can be induced by running 'cat /proc/kcore > /dev/null' on
devices using pstore with the ram backend because kmap_atomic() assumes
lowmem pages are accessible with __va().
During early boot, memblock reserves the pages for the ramoops reserved
memory node in DT that would otherwise be part of the direct lowmem
mapping. Pstore's ram backend reuses those reserved pages to change the
memory type (writeback or non-cached) by passing the pages to vmap()
(see pfn_to_page() usage in persistent_ram_vmap() for more details) with
specific flags. When read_kcore() starts iterating over the vmalloc
region, it runs over the virtual address that vmap() returned for
ramoops. In aligned_vread() the virtual address is passed to
vmalloc_to_page() which returns the page struct for the reserved lowmem
area. That lowmem page is passed to kmap_atomic(), which effectively
calls page_to_virt() that assumes a lowmem page struct must be directly
accessible with __va() and friends. These pages are mapped via vmap()
though, and the lowmem mapping was never made, so accessing them via the
lowmem virtual address oopses like above.
Let's side-step this problem by passing VM_IOREMAP to vmap(). This will
tell vread() to not include the ramoops region in the kcore. Instead the
area will look like a bunch of zeros. The alternative is to teach kmap()
about vmalloc areas that intersect with lowmem. Presumably such a change
isn't a one-liner, and there isn't much interest in inspecting the
ramoops region in kcore files anyway, so the most expedient route is
taken for now.
Cc: Brian Geffon <bgeffon@google.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 404a6043385d ("staging: android: persistent_ram: handle reserving and mapping memory") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20221205233136.3420802-1-swboyd@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
timer_read() was using an empty 100-iteration loop to wait for the
TMR_CVWR register to capture the latest timer counter value. The delay
wasn't long enough. This resulted in CPU idle time being extremely
underreported on PXA168 with CONFIG_NO_HZ_IDLE=y.
Switch to the approach used in the vendor kernel, which implements the
capture delay by reading TMR_CVWR a few times instead.
Fixes: 49cbe78637eb ("[ARM] pxa: add base support for Marvell's PXA168 processor line") Signed-off-by: Doug Brown <doug@schmorgal.com> Link: https://lore.kernel.org/r/20221204005117.53452-3-doug@schmorgal.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 538da83ddbea ("ARM: mvebu: add Device Tree files for Armada 39x SoC and board") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 0d3d96ab0059 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 4de59085091f ("ARM: mvebu: add Device Tree description of the Armada 375 SoC") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 9d8f44f02d4a ("arm: mvebu: add PCIe Device Tree informations for Armada XP") Fixes: 12b69a599745 ("ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable") Fixes: 2163e61c92d9 ("ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: a09a0b7c6ff1 ("arm: mvebu: add PCIe Device Tree informations for Armada 370") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
When the name_assign_type attribute was introduced (commit 685343fc3ba6, "net: add name_assign_type netdev attribute"), the
loopback device was explicitly mentioned as one which would make use
of NET_NAME_PREDICTABLE:
The name_assign_type attribute gives hints where the interface name of a
given net-device comes from. These values are currently defined:
...
NET_NAME_PREDICTABLE:
The ifname has been assigned by the kernel in a predictable way
that is guaranteed to avoid reuse and always be the same for a
given device. Examples include statically created devices like
the loopback device [...]
Switch to that so that reading /sys/class/net/lo/name_assign_type
produces something sensible instead of returning -EINVAL.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
By keep sending L2CAP_CONF_REQ packets, chan->num_conf_rsp increases
multiple times and eventually it will wrap around the maximum number
(i.e., 255).
This patch prevents this by adding a boundary check with
L2CAP_MAX_CONF_RSP
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setup function uvc_function_setup permits control transfer
requests with up to 64 bytes of payload (UVC_MAX_REQUEST_SIZE),
data stage handler for OUT transfer uses memcpy to copy req->actual
bytes to uvc_event->data.data array of size 60. This may result
in an overflow of 4 bytes.
Fixes: cdda479f15cd ("USB gadget: video class function driver") Cc: stable <stable@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com> Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com> Link: https://lore.kernel.org/r/20221206141301.51305-1-szymon.heidrich@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file within last block it can happen that the extent is
already rounded to the blocksize and thus contains the offset we want to
grow up to. In such case we would mistakenly expand the last extent and
make it one block longer than it should be, exposing unallocated block
in a file and causing data corruption. Fix the problem by properly
detecting this case and bailing out.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When preallocation extent is the first one in the extent block, the
code would corrupt extent tree header instead. Fix the problem and use
udf_delete_aext() for deleting extent to avoid some code duplication.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file with a hole, we tried to preserve existing
preallocation for the file. However that is not very useful and
complicates code because the previous extent may need to be rounded to
block boundary as well (which we forgot to do thus causing data
corruption for sequence like:
Currently the check against the max value for the control is being
applied after the value has had the minimum applied and been masked. But
the max value simply indicates the number of volume levels on an SX
control, and as such should just be applied on the raw value.
Fixes: 97eea946b939 ("ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20221125162348.1288005-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.
Ming Lei [Tue, 13 Dec 2022 07:16:55 +0000 (15:16 +0800)]
block: unhash blkdev part inode when the part is deleted
v5.11 changes the blkdev lookup mechanism completely since commit 22ae8ce8b892 ("block: simplify bdev/disk lookup in blkdev_get"),
and small part of the change is to unhash part bdev inode when
deleting partition. Turns out this kind of change does fix one
nasty issue in case of BLOCK_EXT_MAJOR:
1) when one partition is deleted & closed, disk_put_part() is always
called before bdput(bdev), see blkdev_put(); so the part's devt can
be freed & re-used before the inode is dropped
2) then new partition with same devt can be created just before the
inode in 1) is dropped, then the old inode/bdev structurein 1) is
re-used for this new partition, this way causes use-after-free and
kernel panic.
It isn't possible to backport the whole big patchset of "merge struct
block_device and struct hd_struct v4" for addressing this issue.
So fixes it by unhashing part bdev in delete_partition(), and this way
is actually aligned with v5.11+'s behavior.
Backported from the following 5.10.y commit:
5f2f77560591 ("block: unhash blkdev part inode when the part is deleted")
Reported-by: Shiwei Cui <cuishw@inspur.com> Tested-by: Shiwei Cui <cuishw@inspur.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any codepath that zaps page table entries must invoke MMU notifiers to
ensure that secondary MMUs (like KVM) don't keep accessing pages which
aren't mapped anymore. Secondary MMUs don't hold their own references to
pages that are mirrored over, so failing to notify them can lead to page
use-after-free.
I'm marking this as addressing an issue introduced in commit f3f0e1d2150b
("khugepaged: add support of collapse for tmpfs/shmem pages"), but most of
the security impact of this only came in commit 27e1f8273113 ("khugepaged:
enable collapse pmd for pte-mapped THP"), which actually omitted flushes
for the removal of present PTEs, not just for the removal of empty page
tables.
Link: https://lkml.kernel.org/r/20221129154730.2274278-3-jannh@google.com Link: https://lkml.kernel.org/r/20221128180252.1684965-3-jannh@google.com Link: https://lkml.kernel.org/r/20221125213714.4115729-3-jannh@google.com Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[manual backport: this code was refactored from two copies into a common
helper between 5.15 and 6.0;
pmd collapse for PTE-mapped THP was only added in 5.4;
MMU notifier API changed between 4.19 and 5.4] Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 70cbc3cc78a99 ("mm: gup: fix the fast GUP race against THP
collapse"), the lockless_pages_from_mm() fastpath rechecks the pmd_t to
ensure that the page table was not removed by khugepaged in between.
However, lockless_pages_from_mm() still requires that the page table is
not concurrently freed. Fix it by sending IPIs (if the architecture uses
semi-RCU-style page table freeing) before freeing/reusing page tables.
Link: https://lkml.kernel.org/r/20221129154730.2274278-2-jannh@google.com Link: https://lkml.kernel.org/r/20221128180252.1684965-2-jannh@google.com Link: https://lkml.kernel.org/r/20221125213714.4115729-2-jannh@google.com Fixes: ba76149f47d8 ("thp: khugepaged") Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[manual backport: two of the three places in khugepaged that can free
ptes were refactored into a common helper between 5.15 and 6.0;
TLB flushing was refactored between 5.4 and 5.10;
TLB flushing was refactored between 4.19 and 5.4;
pmd collapse for PTE-mapped THP was only added in 5.4;
ugly hack for s390 in <=4.19 and arm] Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In an earlier commit, I added a bounds check to prevent an out of bounds
read and a WARN(). On further discussion and consideration that check
was probably too aggressive. Instead of returning -EINVAL, a better fix
would be to just prevent the out of bounds read but continue the process.
Background: The value of "pp->rxq_def" is a number between 0-7 by default,
or even higher depending on the value of "rxq_number", which is a module
parameter. If the value is more than the number of available CPUs then
it will trigger the WARN() in cpu_max_bits_warn().
Fixes: e8b4fc13900b ("net: mvneta: Prevent out of bounds read in mvneta_config_rss()") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/Y5A7d1E5ccwHTYPf@kadam Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from
hardware interrupt context or with interrupts being disabled.
So replace kfree_skb/dev_kfree_skb() with dev_kfree_skb_irq()
and dev_consume_skb_irq() under spin_lock_irq().
Commit ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in
the non-linear area") introduced a (valid) build warning. There have
even been reports of this problem breaking networking of Xen guests.
Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pp->indir[0] value comes from the user. It is passed to:
if (cpu_online(pp->rxq_def))
inside the mvneta_percpu_elect() function. It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.
Fixes: cad5d847a093 ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect") Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d70e53262f5c ("net: Microchip encx24j600 driver") Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ieee802154_if_add() allocates wpan_dev as netdev's private data, but not
init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage
the list when device register/unregister, and may lead to null-ptr-deref.
Use INIT_LIST_HEAD() on it to initialize it correctly.
Without this change, the interrupt test fail with MSI-X environment:
$ sudo ethtool -t enp0s2 offline
[ 43.921783] igb 0000:00:02.0: offline testing starting
[ 44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[ 44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 51.272202] igb 0000:00:02.0: testing shared interrupt
[ 56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 4
Loopback test (offline) 0
Link test (on/offline) 0
Here, "4" means an expected interrupt was not delivered.
To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:
$ sudo ethtool -t enp0s2 offline
[ 42.762985] igb 0000:00:02.0: offline testing starting
[ 50.141967] igb 0000:00:02.0: testing shared interrupt
[ 56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: 4eefa8f01314 ("igb: add single vector msi-x testing to interrupt test") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.
This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;
This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de047d ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported shift-out-of-bounds in hid_report_raw_event.
microsoft 0003:045E:07DA.0001: hid_field_extract() called with n (128) >
32! (swapper/0)
======================================================================
UBSAN: shift-out-of-bounds in drivers/hid/hid-core.c:1323:20
shift exponent 127 is too large for 32-bit type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rc4-syzkaller-00159-g4bbf3422df78 #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x3a6/0x420 lib/ubsan.c:322
snto32 drivers/hid/hid-core.c:1323 [inline]
hid_input_fetch_field drivers/hid/hid-core.c:1572 [inline]
hid_process_report drivers/hid/hid-core.c:1665 [inline]
hid_report_raw_event+0xd56/0x18b0 drivers/hid/hid-core.c:1998
hid_input_report+0x408/0x4f0 drivers/hid/hid-core.c:2066
hid_irq_in+0x459/0x690 drivers/hid/usbhid/hid-core.c:284
__usb_hcd_giveback_urb+0x369/0x530 drivers/usb/core/hcd.c:1671
dummy_timer+0x86b/0x3110 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0xf5/0x210 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x76a/0x980 kernel/time/timer.c:1790
run_timer_softirq+0x63/0xf0 kernel/time/timer.c:1803
__do_softirq+0x277/0x75b kernel/softirq.c:571
__irq_exit_rcu+0xec/0x170 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x91/0xb0 arch/x86/kernel/apic/apic.c:1107
======================================================================
If the size of the integer (unsigned n) is bigger than 32 in snto32(),
shift exponent will be too large for 32-bit type 'int', resulting in a
shift-out-of-bounds bug.
Fix this by adding a check on the size of the integer (unsigned n) in
snto32(). To add support for n greater than 32 bits, set n to 32, if n
is greater than 32.
Sanity checks were added to verify the v4l2_bt_timings blanking fields
in order to avoid integer overflows when userspace passes weird values.
But that assumed that userspace would correctly fill in the front porch,
backporch and sync values, but sometimes all you know is the total
blanking, which is then assigned to just one of these fields.
And that can fail with these checks.
So instead set a maximum for the total horizontal and vertical
blanking and check that each field remains below that.
That is still sufficient to avoid integer overflows, but it also
allows for more flexibility in how userspace fills in these fields.
Commit 20b92a30b561 ("mmc: sdhci: update signal voltage switch code")
removed voltage switch delays from sdhci because mmc core had been
enhanced to support them. However that assumed that sdhci_set_ios()
did a single clock change, which it did not, and so the delays in mmc
core, which should have come after the first clock change, were not
effective.
Fix by avoiding re-configuring UHS and preset settings when the clock
is turning on and the settings have not changed. That then also avoids
the associated clock changes, so that then sdhci_set_ios() does a single
clock change when voltage switching, and the mmc core delays become
effective.
To do that has meant keeping track of driver strength (host->drv_type),
and cases of reinitialization (host->reinit_uhs).
Note also, the 'turning_on_clk' restriction should not be necessary
but is done to minimize the impact of the change on stable kernels.
Fixes: 20b92a30b561 ("mmc: sdhci: update signal voltage switch code") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20221128133259.38305-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rcutorture scripts currently expect the user to create the
tools/testing/selftests/rcutorture/initrd directory. Should the user
fail to do this, the kernel build will fail with obscure and confusing
error messages. This commit therefore adds explicit checks for the
tools/testing/selftests/rcutorture/initrd directory, and if not present,
creates one on systems on which dracut is installed. If this directory
could not be created, a less obscure error message is emitted and the
test is aborted.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Connor Shu <Connor.Shu@ibm.com>
[ paulmck: Adapt the script to fit into the rcutorture framework and
severely abbreviate the initrd/init script. ] Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So remove kfree_skb()
from the spin_lock_irqsave() section and use the already existing
"drop" label in xenvif_start_xmit() for dropping the SKB. At the
same time replace the dev_kfree_skb() call there with a call of
dev_kfree_skb_any(), as xenvif_start_xmit() can be called with
disabled interrupts.
This is XSA-424 / CVE-2022-42328 / CVE-2022-42329.
Fixes: be81992f9086 ("xen/netback: don't queue unlimited number of packages") Reported-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some cases, the frontend may send a packet where the protocol headers
are spread across multiple slots. This would result in netback creating
an skb where the protocol headers spill over into the non-linear area.
Some drivers and NICs don't handle this properly resulting in an
interface reset or worse.
This issue was introduced by the removal of an unconditional skb pull in
the tx path to improve performance. Fix this without reintroducing the
pull by setting up grant copy ops for as many slots as needed to reach
the XEN_NETBACK_TX_COPY_LEN size. Adjust the rest of the code to handle
multiple copy operations per skb.
This is XSA-423 / CVE-2022-3643.
Fixes: 7e5d7753956b ("xen-netback: remove unconditional __pskb_pull_tail() in guest Tx path") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Store the frame address where arm_get_current_stackframe() looks for it
(ARM_r7 instead of ARM_fp if CONFIG_THUMB2_KERNEL=y). Otherwise frame->fp
gets set to 0, causing unwind_frame() to fail.
The V4L2_MEMORY_USERPTR interface is long deprecated and shouldn't be
used (and is discouraged for any modern v4l drivers). And Seth Jenkins
points out that the fallback to VM_PFNMAP/VM_IO is fundamentally racy
and dangerous.
Note that it's not even a case that should trigger, since any normal
user pointer logic ends up just using the pin_user_pages_fast() call
that does the proper page reference counting. That's not the problem
case, only if you try to use special device mappings do you have any
issues.
Normally I'd just remove this during the merge window, but since Seth
pointed out the problem cases, we really want to know as soon as
possible if there are actually any users of this odd special case of a
legacy interface. Neither Hans nor Mauro seem to think that such
mis-uses of the old legacy interface should exist. As Mauro says:
"See, V4L2 has actually 4 streaming APIs:
- Kernel-allocated mmap (usually referred simply as just mmap);
- USERPTR mmap;
- read();
- dmabuf;
The USERPTR is one of the oldest way to use it, coming from V4L
version 1 times, and by far the least used one"
And Hans chimed in on the USERPTR interface:
"To be honest, I wouldn't mind if it goes away completely, but that's a
bit of a pipe dream right now"
but while removing this legacy interface entirely may be a pipe dream we
can at least try to remove the unlikely (and actively broken) case of
using special device mappings for USERPTR accesses.
This replaces it with a WARN_ONCE() that we can remove once we've
hopefully confirmed that no actual users exist.
NOTE! Longer term, this means that a 'struct frame_vector' only ever
contains proper page pointers, and all the games we have with converting
them to pages can go away (grep for 'frame_vector_to_pages()' and the
uses of 'vec->is_pfns'). But this is just the first step, to verify
that this code really is all dead, and do so as quickly as possible.
Reported-by: Seth Jenkins <sethjenkins@google.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
proc_skip_spaces() seems to think it is working on C strings, and ends
up being just a wrapper around skip_spaces() with a really odd calling
convention.
Instead of basing it on skip_spaces(), it should have looked more like
proc_skip_char(), which really is the exact same function (except it
skips a particular character, rather than whitespace). So use that as
inspiration, odd coding and all.
Now the calling convention actually makes sense and works for the
intended purpose.
proc_get_long() is passed a size_t, but then assigns it to an 'int'
variable for the length. Let's not do that, even if our IO paths are
limited to MAX_RW_COUNT (exactly because of these kinds of type errors).
Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.
Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.
projects / thirdparty / kernel / stable.git / log
