recordmcount edits the file in-place, which can cause problems when
using ccache in hardlink mode. Arrange for recordmcount to break a
hardlinked object.
Fix parent-device reference leak due to SPI-core taking an unnecessary
reference to the parent when allocating the master structure, a
reference that was never released.
Note that driver core takes its own reference to the parent when the
master device is registered.
Fixes: 49dce689ad4e ("spi doesn't need class_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When shutting down the device, the struct ser_cardstate must not be
kfree()d immediately after the call to platform_device_unregister()
since the embedded struct platform_device is still in use.
Move the kfree() call to the release method instead.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Fixes: 2869b23e4b95 ("drivers/isdn/gigaset: new M101 driver (v2)") Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are two issue here.
1) cnt starts as maxloop + 1 so all these loops iterate one more time
than intended.
2) At the end of the loop we test for "if (maxloop && !cnt)" but for
the first two loops, we end with cnt equal to -1. Changing this to
a pre-op means we end with cnt set to 0.
Fixes: cae86d4a4e56 ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For the little-endian SH771x kernels the driver has to byte-swap the RX/TX
buffers, however yet unset physcial address from the TX descriptor is used
to call sh_eth_soft_swap(). Use 'skb->data' instead...
Fixes: 31fcb99d9958 ("net: sh_eth: remove __flush_purge_region") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.
Commit 2d1cb7f658fb ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.
However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.
Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).
Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.
v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: open-code usb_audio_info()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add helper macros with a little bit of preprocessor magic to
automatically compute the length of a TLV item. This lets us avoid
having to compute this by hand, and will allow to use items that do
not use a fixed length.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A line discipline which does not define a receive_buf() method can
can cause a GPF if data is ever received [1]. Oddly, this was known
to the author of n_tracesink in 2011, but never fixed.
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some users of rfkill, like NFC and cfg80211, use a dynamic name when
allocating rfkill, in those cases dev_name(). Therefore, the pointer
passed to rfkill_alloc() might not be valid forever, I specifically
found the case that the rfkill name was quite obviously an invalid
pointer (or at least garbage) when the wiphy had been renamed.
Fix this by making a copy of the rfkill name in rfkill_alloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some ciphers actually support encrypting zero length plaintexts. For
example, many AEAD modes support this. The resulting ciphertext for
those winds up being only the authentication tag, which is a result of
the key, the iv, the additional data, and the fact that the plaintext
had zero length. The blkcipher constructors won't copy the IV to the
right place, however, when using a zero length input, resulting in
some significant problems when ciphers call their initialization
routines, only to find that the ->iv parameter is uninitialized. One
such example of this would be using chacha20poly1305 with a zero length
input, which then calls chacha20, which calls the key setup routine,
which eventually OOPSes due to the uninitialized ->iv member.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If diu_ops is not implemented on platform, kernel will access a NULL
pointer. We need to check this pointer in DIU initialization.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Acked-by: Timur Tabi <timur@tabi.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While cooking the sctp np->opt rcu fixes, I forgot to move
one rcu_read_unlock() after the added rcu_dereference() in
sctp_v6_get_dst()
This gave lockdep warnings reported by Dave Jones.
Fixes: c836a8ba9386 ("ipv6: sctp: add rcu protection around np->opt") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
when A sends a data to B, then A close() and enter into SHUTDOWN_PENDING
state, if B neither claim his rwnd is 0 nor send SACK for this data, A
will keep retransmitting this data until t5 timeout, Max.Retrans times
can't work anymore, which is bad.
if B's rwnd is not 0, it should send abort after Max.Retrans times, only
when B's rwnd == 0 and A's retransmitting beyonds Max.Retrans times, A
will start t5 timer, which is also commit f8d960524328 ("sctp: Enforce
retransmission limit during shutdown") means, but it lacks the condition
peer rwnd == 0.
so fix it by adding a bit (zero_window_announced) in peer to record if
the last rwnd is 0. If it was, zero_window_announced will be set. and use
this bit to decide if start t5 timer when local.state is SHUTDOWN_PENDING.
Fixes: commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: change sack_needed to bitfield as done earlier upstream] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently slhc_init() treats out-of-range values of rslots and tslots
as equivalent to 0, except that if tslots is too large it will
dereference a null pointer (CVE-2015-7799).
Add a range-check at the top of the function and make it return an
ERR_PTR() on error instead of NULL. Change the callers accordingly.
Compile-tested only.
Reported-by: 郭永刚 <guoyonggang@360.cn>
References: http://article.gmane.org/gmane.comp.security.oss.general/17908 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust indentation]
Using bit fields is dangerous on ppc64/sparc64, as the compiler [1]
uses 64bit instructions to manipulate them.
If the 64bit word includes any atomic_t or spinlock_t, we can lose
critical concurrent changes.
This is happening in af_unix, where unix_sk(sk)->gc_candidate/
gc_maybe_cycle/lock share the same 64bit word.
This leads to fatal deadlock, as one/several cpus spin forever
on a spinlock that will never be available again.
A safer way would be to use a long to store flags.
This way we are sure compiler/arch wont do bad things.
As we own unix_gc_lock spinlock when clearing or setting bits,
we can use the non atomic __set_bit()/__clear_bit().
recursion_level can share the same 64bit location with the spinlock,
as it is set only with this spinlock held.
[1] bug fixed in gcc-4.8.0 :
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52080
Reported-by: Ambrose Feinstein <ambrose@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
With b3ca9b02b00704053a38bfe4c31dbbb9c13595d0, the AF_UNIX SOCK_STREAM
receive code was changed from using mutex_lock(&u->readlock) to
mutex_lock_interruptible(&u->readlock) to prevent signals from being
delayed for an indefinite time if a thread sleeping on the mutex
happened to be selected for handling the signal. But this was never a
problem with the stream receive code (as opposed to its datagram
counterpart) as that never went to sleep waiting for new messages with the
mutex held and thus, wouldn't cause secondary readers to block on the
mutex waiting for the sleeping primary reader. As the interruptible
locking makes the code more complicated in exchange for no benefit,
change it back to using mutex_lock.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AF_INET, AF_INET6 sockets actually only support 8-bit protocol
identifiers. inet_sock's skc_protocol field thus is sized accordingly,
thus larger protocol identifiers simply cut off the higher bits and
store a zero in the protocol fields.
This could lead to e.g. NULL function pointer because as a result of
the cut off inet_num is zero and we call down to inet_autobind, which
is NULL for raw sockets.
I found no particular commit which introduced this problem.
CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by: 郭永刚 <guoyonggang@360.cn> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: open-code U8_MAX] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
SCTP is lacking proper np->opt cloning at accept() time.
TCP and DCCP use ipv6_dup_options() helper, do the same
in SCTP.
We might later factorize this code in a common helper to avoid
future mistakes.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy
related to disabling sock timestamp.
When SCTP accepts an association or peel one off, it copies sock flags
but forgot to call net_enable_timestamp() if a packet timestamping flag
was copied, leading to extra calls to net_disable_timestamp() whenever
such clones were closed.
The fix is to call net_enable_timestamp() whenever we copy a sock with
that flag on, like tcp does.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: SK_FLAGS_TIMESTAMP is newly defined] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets.
We need to call inet6_destroy_sock() to properly release
inet6 specific fields.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
- Drop changes to l2tp
- Fix an additional use of np->opt in tcp_v6_send_synack()
- Fold in commit 43264e0bd963 ("ipv6: remove unnecessary codes in tcp_ipv6.c")
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
opt always equals np->opts, so it is meaningless to define opt, and
check if opt does not equal np->opts and then try to free opt.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a fragmented multicast packet is received on an ethernet device which
has an active macvlan on top of it, each fragment is duplicated and
received both on the underlying device and the macvlan. If some
fragments for macvlan are processed before the whole packet for the
underlying device is reassembled, the "overlapping fragments" test in
ip6_frag_queue() discards the whole fragment queue.
To resolve this, add device ifindex to the search key and require it to
match reassembling multicast packets and packets to link-local
addresses.
Note: similar patch has been already submitted by Yoshifuji Hideaki in
http://patchwork.ozlabs.org/patch/220979/
but got lost and forgotten for some reason.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When destroying an mrt table the static mfc entries and the static
devices are kept, which leads to devices that can never be destroyed
(because of refcnt taken) and leaked memory, for example:
unreferenced object 0xffff880034c144c0 (size 192):
comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s)
hex dump (first 32 bytes):
98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4....
ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................
backtrace:
[<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300
[<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910
[<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0
[<ffffffff8153e490>] ip_setsockopt+0x30/0xa0
[<ffffffff81564e13>] raw_setsockopt+0x33/0x90
[<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20
[<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0
[<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Make sure that everything is cleaned on netns destruction.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Further investigation showed that this can happen when an *odd* number of
fds are being passed over AF_UNIX sockets.
In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)),
where i is the number of successfully passed fds, differ by 4 bytes due
to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary
on 64 bit. The padding is used to align subsequent cmsg headers in the
control buffer.
When the control buffer passed in from the receiver side *lacks* these 4
bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will
overflow in scm_detach_fds():
int cmlen = CMSG_LEN(i * sizeof(int)); <--- cmlen w/o tail-padding
err = put_user(SOL_SOCKET, &cm->cmsg_level);
if (!err)
err = put_user(SCM_RIGHTS, &cm->cmsg_type);
if (!err)
err = put_user(cmlen, &cm->cmsg_len);
if (!err) {
cmlen = CMSG_SPACE(i * sizeof(int)); <--- cmlen w/ 4 byte extra tail-padding
msg->msg_control += cmlen;
msg->msg_controllen -= cmlen; <--- iff no tail-padding space here ...
} ... wrap-around
F.e. it will wrap to a length of 18446744073709551612 bytes in case the
receiver passed in msg->msg_controllen of 20 bytes, and the sender
properly transferred 1 fd to the receiver, so that its CMSG_LEN results
in 20 bytes and CMSG_SPACE in 24 bytes.
In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an
issue in my tests as alignment seems always on 4 byte boundary. Same
should be in case of native 32 bit, where we end up with 4 byte boundaries
as well.
In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving
a single fd would mean that on successful return, msg->msg_controllen is
being set by the kernel to 24 bytes instead, thus more than the input
buffer advertised. It could f.e. become an issue if such application later
on zeroes or copies the control buffer based on the returned msg->msg_controllen
elsewhere.
Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253).
Going over the code, it seems like msg->msg_controllen is not being read
after scm_detach_fds() in scm_recv() anymore by the kernel, good!
Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg())
and unix_stream_recvmsg(). Both return back to their recvmsg() caller,
and ___sys_recvmsg() places the updated length, that is, new msg_control -
old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen
in the example).
Long time ago, Wei Yongjun fixed something related in commit 1ac70e7ad24a
("[NET]: Fix function put_cmsg() which may cause usr application memory
overflow").
RFC3542, section 20.2. says:
The fields shown as "XX" are possible padding, between the cmsghdr
structure and the data, and between the data and the next cmsghdr
structure, if required by the implementation. While sending an
application may or may not include padding at the end of last
ancillary data in msg_controllen and implementations must accept both
as valid. On receiving a portable application must provide space for
padding at the end of the last ancillary data as implementations may
copy out the padding at the end of the control message buffer and
include it in the received msg_controllen. When recvmsg() is called
if msg_controllen is too small for all the ancillary data items
including any trailing padding after the last item an implementation
may set MSG_CTRUNC.
Since we didn't place MSG_CTRUNC for already quite a long time, just do
the same as in 1ac70e7ad24a to avoid an overflow.
Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix
error in SCM_RIGHTS code sample"). Some people must have copied this (?),
thus it got triggered in the wild (reported several times during boot by
David and HacKurx).
No Fixes tag this time as pre 2002 (that is, pre history tree).
Reported-by: David Sterba <dave@jikos.cz> Reported-by: HacKurx <hackurx@gmail.com> Cc: PaX Team <pageexec@freemail.hu> Cc: Emese Revfy <re.emese@gmail.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
His program is specifically attempting a Cross SYN TCP exchange,
that we support (for the pleasure of hackers ?), but it looks we
lack proper tcp->copied_seq initialization.
Thanks again Dmitry for your report and testings.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Tested-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Claus Jensen <claus.jensen@microsemi.com> CC: Claus Jensen <claus.jensen@microsemi.com> CC: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to arch/sh/kernel/syscalls_64.S and common sense, __NR_fgetxattr
has to be defined to 259, but it doesn't. Instead, it's defined to 269,
which is of course used by another syscall, __NR_sched_setaffinity in this
case.
This bug was found by strace test suite.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently at the beginning of hugetlb_fault(), we call huge_pte_offset()
and check whether the obtained *ptep is a migration/hwpoison entry or
not. And if not, then we get to call huge_pte_alloc(). This is racy
because the *ptep could turn into migration/hwpoison entry after the
huge_pte_offset() check. This race results in BUG_ON in
huge_pte_alloc().
We don't have to call huge_pte_alloc() when the huge_pte_offset()
returns non-NULL, so let's fix this bug with moving the code into else
block.
Note that the *ptep could turn into a migration/hwpoison entry after
this block, but that's not a problem because we have another
!pte_present check later (we never go into hugetlb_no_page() in that
case.)
Fixes: 290408d4a250 ("hugetlb: hugepage migration core") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tetsuo Handa has reported that the system might basically livelock in
OOM condition without triggering the OOM killer.
The issue is caused by internal dependency of the direct reclaim on
vmstat counter updates (via zone_reclaimable) which are performed from
the workqueue context. If all the current workers get assigned to an
allocation request, though, they will be looping inside the allocator
trying to reclaim memory but zone_reclaimable can see stalled numbers so
it will consider a zone reclaimable even though it has been scanned way
too much. WQ concurrency logic will not consider this situation as a
congested workqueue because it relies that worker would have to sleep in
such a situation. This also means that it doesn't try to spawn new
workers or invoke the rescuer thread if the one is assigned to the
queue.
In order to fix this issue we need to do two things. First we have to
let wq concurrency code know that we are in trouble so we have to do a
short sleep. In order to prevent from issues handled by 0e093d99763e
("writeback: do not sleep on the congestion queue if there are no
congested BDIs or if significant congestion is not being encountered in
the current zone") we limit the sleep only to worker threads which are
the ones of the interest anyway.
The second thing to do is to create a dedicated workqueue for vmstat and
mark it WQ_MEM_RECLAIM to note it participates in the reclaim and to
have a spare worker thread for it.
Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Tejun Heo <tj@kernel.org> Cc: Cristopher Lameter <clameter@sgi.com> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Arkadiusz Miskiewicz <arekm@maven.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.
Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources
The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).
The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.
How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:
if (startsg->length + dma_len > max_seg_size)
break;
When it finishes coalescing adjacent entries, it allocates the mapping:
It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.
To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
if (startsg->length + dma_len > max_seg_size)
break;
to
if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
break;
This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
There are few defects in vga_get() related to signal hadning:
- we shouldn't check for pending signals for TASK_UNINTERRUPTIBLE
case;
- if we found pending signal we must remove ourself from wait queue
and change task state back to running;
- -ERESTARTSYS is more appropriate, I guess.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.
Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org> CC: linux-kernel@vger.kernel.org Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Tony Camuso <tcamuso@redhat.com> Signed-off-by: Corey Minyard <cminyard@mvista.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For block devices the pagecache is associated with the inode
on bdevfs, not with the aliasing ones on the mountable filesystems.
The latter have its own ->i_data empty and ->i_mapping pointing
to the (unique per major/minor) bdevfs inode. That guarantees
cache coherence between all block device inodes with the same
device number.
Eviction of an alias inode has no business trying to evict the
pages belonging to bdevfs one; moreover, ->i_mapping is only
safe to access when the thing is opened. At the time of
->evict_inode() the victim is definitely *not* opened. We are
about to kill the address space embedded into struct inode
(inode->i_data) and that's what we need to empty of any pages.
9p instance tries to empty inode->i_mapping instead, which is
both unsafe and bogus - if we have several device nodes with
the same device number in different places, closing one of them
should not try to empty the (shared) page cache.
Fortunately, other instances in the tree are OK; they are
evicting from &inode->i_data instead, as 9p one should.
Reported-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com> Tested-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
rme96 driver needs to reset DAC depending on the sample rate, and this
results in resetting to the max volume suddenly. It's because of the
missing call of snd_rme96_apply_dac_volume().
However, calling this function right after the DAC reset still may not
work, and we need some delay before this call. Since the DAC reset
and the procedure after that are performed in the spinlock, we delay
the DAC volume restore at the end after the spinlock.
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.
The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.
Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.
Signed-off-by: Xunlei Pang <xlpang@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2:
- There's no dlo_mask to initialise
- Adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Because wakeups can (fundamentally) be late, a task might not be in
the expected state. Therefore testing against a task's state is racy,
and can yield false positives.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: oleg@redhat.com Fixes: 9067ac85d533 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task") Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2:
- s/master_mutex/struct_mutex/
- drm_new_set_master() must drop struct_mutex while calling
drm_driver::master_create
- Adjust filename, context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An interface may need to assert a lock invariant and not flood the
system logs; add a lockdep helper macro equivalent to
lockdep_assert_held() which only WARNs once.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.
If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a5344f ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.
The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 52ad353a5344f "(igmp: fix the problem when mc leave group") Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
If we pass in an empty nfs_fattr struct to nfs_update_inode, it will
(correctly) not update any of the attributes, but it then clears the
NFS_INO_INVALID_ATTR flag, which indicates that the attributes are
up to date. Don't clear the flag if the fattr struct has no valid
attrs to apply.
Reviewed-by: Steve French <steve.french@primarydata.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Sasha's found a NULL pointer dereference in the RDS connection code when
sending a message to an apparently unbound socket. The problem is caused
by the code checking if the socket is bound in rds_sendmsg(), which checks
the rs_bound_addr field without taking a lock on the socket. This opens a
race where rs_bound_addr is temporarily set but where the transport is not
in rds_bind(), leading to a NULL pointer dereference when trying to
dereference 'trans' in __rds_conn_create().
Vegard wrote a reproducer for this issue, so kindly ask him to share if
you're interested.
I cannot reproduce the NULL pointer dereference using Vegard's reproducer
with this patch, whereas I could without.
Complete earlier incomplete fix to CVE-2015-6937:
74e98eb08588 ("RDS: verify the underlying transport exists before creating a connection")
Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Vegard Nossum <vegard.nossum@oracle.com> Reviewed-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ted and Namjae have reported that truncated pages don't get timely
reclaimed after being truncated in data=journal mode. The following test
triggers the issue easily:
for (i = 0; i < 1000; i++) {
pwrite(fd, buf, 1024*1024, 0);
fsync(fd);
fsync(fd);
ftruncate(fd, 0);
}
The reason is that journal_unmap_buffer() finds that truncated buffers
are not journalled (jh->b_transaction == NULL), they are part of
checkpoint list of a transaction (jh->b_cp_transaction != NULL) and have
been already written out (!buffer_dirty(bh)). We clean such buffers but
we leave them in the checkpoint list. Since checkpoint transaction holds
a reference to the journal head, these buffers cannot be released until
the checkpoint transaction is cleaned up. And at that point we don't
call release_buffer_page() anymore so pages detached from mapping are
lingering in the system waiting for reclaim to find them and free them.
Fix the problem by removing buffers from transaction checkpoint lists
when journal_unmap_buffer() finds out they don't have to be there
anymore.
Reported-and-tested-by: Namjae Jeon <namjae.jeon@samsung.com> Fixes: de1b794130b130e77ffa975bb58cb843744f9ae5 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In ext4, the bottom two bits of {a,c,m}time_extra are used to extend
the {a,c,m}time fields, deferring the year 2038 problem to the year
2446.
When decoding these extended fields, for times whose bottom 32 bits
would represent a negative number, sign extension causes the 64-bit
extended timestamp to be negative as well, which is not what's
intended. This patch corrects that issue, so that the only negative
{a,c,m}times are those between 1901 and 1970 (as per 32-bit signed
timestamps).
Some older kernels might have written pre-1970 dates with 1,1 in the
extra bits. This patch treats those incorrectly-encoded dates as
pre-1970, instead of post-2311, until kernel 4.20 is released.
Hopefully by then e2fsck will have fixed up the bad data.
Also add a comment explaining the encoding of ext4's extra {a,c,m}time
bits.
Signed-off-by: David Turner <novalis@novalis.org> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reported-by: Mark Harris <mh8928@yahoo.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=23732 Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.
rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 296291cdd162 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2:
- Adjust context
- Also delete unused sysv_fast_symlink_inode_operations] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Rainer Weikusat <rweikusat@mobileactivedefense.com> writes:
An AF_UNIX datagram socket being the client in an n:1 association with
some server socket is only allowed to send messages to the server if the
receive queue of this socket contains at most sk_max_ack_backlog
datagrams. This implies that prospective writers might be forced to go
to sleep despite none of the message presently enqueued on the server
receive queue were sent by them. In order to ensure that these will be
woken up once space becomes again available, the present unix_dgram_poll
routine does a second sock_poll_wait call with the peer_wait wait queue
of the server socket as queue argument (unix_dgram_recvmsg does a wake
up on this queue after a datagram was received). This is inherently
problematic because the server socket is only guaranteed to remain alive
for as long as the client still holds a reference to it. In case the
connection is dissolved via connect or by the dead peer detection logic
in unix_dgram_sendmsg, the server socket may be freed despite "the
polling mechanism" (in particular, epoll) still has a pointer to the
corresponding peer_wait queue. There's no way to forcibly deregister a
wait queue with epoll.
Based on an idea by Jason Baron, the patch below changes the code such
that a wait_queue_t belonging to the client socket is enqueued on the
peer_wait queue of the server whenever the peer receive queue full
condition is detected by either a sendmsg or a poll. A wake up on the
peer queue is then relayed to the ordinary wait queue of the client
socket via wake function. The connection to the peer wait queue is again
dissolved if either a wake up is about to be relayed or the client
socket reconnects or a dead peer is detected or the client socket is
itself closed. This enables removing the second sock_poll_wait from
unix_dgram_poll, thus avoiding the use-after-free, while still ensuring
that no blocked writer sleeps forever.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Fixes: ec0d215f9420 ("af_unix: fix 'poll for write'/connected DGRAM sockets") Reviewed-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.
The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.
"This is what happens when the device is turned on (without modifying
the drivers):
[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:
[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14
Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se> Tested-by: Daniele Palmas <dnlplm@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[bwh: Backported to 3.2: s/SJA1000_IR/REG_IR/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef1e ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to wait for the flying timers, since we
are going to free the mrtable right after it.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If md->signature == MAC_DRIVER_MAGIC and md->block_size == 1023, a single
512 byte sector would be read (secsize / 512). However the partition
structure would be located past the end of the buffer (secsize % 512).
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jens Axboe <axboe@fb.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e8d ("net: introduce rx_handler results and logic around that") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
Fixes: eb2b9311fd00 ("mac80211: mesh path table implementation") Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 102f4d900c9c8f5e ("FS-Cache: Handle a write to the page immediately beyond the EOF marker") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45ce ("net: Call netdev_features_change() from netdev_update_features()") CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sachin Pandhare <sachinpandhare@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[bwh: Backported to 3.2: wm8962_reg is a sparse array, not an array of
{ offset, value } pairs] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e460 ("usb: musb: add ulpi access operations") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ben Hutchings [Wed, 23 Dec 2015 13:04:59 +0000 (13:04 +0000)]
USB: ti_usb_3410_502: Fix ID table size
Commit 35a2fbc941ac ("USB: serial: ti_usb_3410_5052: new device id for
Abbot strip port cable") failed to update the size of the
ti_id_table_3410 array. This doesn't need to be fixed upstream
following commit d7ece6515e12 ("USB: ti_usb_3410_5052: remove
vendor/product module parameters") but should be fixed in stable
branches older than 3.12.
Backports of commit c9d09dc7ad10 ("USB: serial: ti_usb_3410_5052: add
Abbott strip port ID to combined table as well.") similarly failed to
update the size of the ti_id_table_combined array.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
now sctp auth cannot work well when setting a hmacid manually, which
is caused by that we didn't use the network order for hmacid, so fix
it by adding the transformation in sctp_auth_ep_set_hmacs.
even we set hmacid with the network order in userspace, it still
can't work, because of this condition in sctp_auth_ep_set_hmacs():
if (id > SCTP_AUTH_HMAC_ID_MAX)
return -EOPNOTSUPP;
so this wasn't working before and thus it won't break compatibility.
Fixes: 65b07e5d0d09 ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I got a report about unkillable task eating CPU. Further
investigation shows, that the problem is in the fuse_fill_write_pages()
function. If iov's first segment has zero length, we get an infinite
loop, because we never reach iov_iter_advance() call.
Fix this by calling iov_iter_advance() before repeating an attempt to
copy data from userspace.
A similar problem is described in 124d3b7041f ("fix writev regression:
pan hanging unkillable and un-straceable"). If zero-length segmend
is followed by segment with invalid address,
iov_iter_fault_in_readable() checks only first segment (zero-length),
iov_iter_copy_from_user_atomic() skips it, fails at second and
returns zero -> goto again without skipping zero-length segment.
Patch calls iov_iter_advance() before goto again: we'll skip zero-length
segment at second iteraction and iov_iter_fault_in_readable() will detect
invalid address.
Special thanks to Konstantin Khlebnikov, who helped a lot with the commit
description.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Maxim Patlasov <mpatlasov@parallels.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Signed-off-by: Miklos Szeredi <miklos@szeredi.hu> Fixes: ea9b9907b82a ("fuse: implement perform_write") Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
Under low memory conditions, tcp_sk_init() and icmp_sk_init()
can both iterate on all possible cpus and call inet_ctl_sock_destroy(),
with eventual NULL pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ani Sinha <ani@arista.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: ipmr doesn't implement IPSTATS_MIB_OUTOCTETS] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Either of pskb_pull() or pskb_trim() may fail under low memory conditions.
If rds_tcp_data_recv() ignores such failures, the application will
receive corrupted data because the skb has not been correctly
carved to the RDS datagram size.
Avoid this by handling pskb_pull/pskb_trim failure in the same
manner as the skb_clone failure: bail out of rds_tcp_data_recv(), and
retry via the deferred call to rds_send_worker() that gets set up on
ENOMEM from rds_tcp_read_sock()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / thirdparty / kernel / stable.git / log
