Hauke Mehrtens [Sat, 26 Jun 2021 22:52:50 +0000 (00:52 +0200)]
ltq-deu: Mark lantiq DEU broken
When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any
more. It fails with this error message:
daemon.err hostapd: nl80211: kernel reports: key addition failed
daemon.err hostapd: Interface initialization failed
OpenWrt uses the standard Linux crypto API in the wifi drivers now
and this probably makes the system offload more crypto operations to
special hardware like the Lantiq DEU. There is probably a bug in the DEU
and these operations fail and then hostapd does not start the interface.
Do not include the Lantiq DEU by default any more.
Ansuel Smith [Thu, 20 May 2021 21:41:57 +0000 (23:41 +0200)]
ipq806x: fix dedicated cpufreq driver
2 small fix for the dedicated cpufreq driver:
- Fix index wrongly used as the current cpu
- Exit early if a bad freq is detected. In the current state the freq
is applied anyway even with invalid state.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Thu, 20 May 2021 21:39:36 +0000 (23:39 +0200)]
ipq806x: fix missing 1.4ghz cache freq for ipq8065 SoC
With the new implementation of the dedicated cpufreq driver,
the 1.4 Ghz was only dropped and not added to the ipq8065 SoC.
Fix this to improve performance.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Tue, 25 May 2021 00:58:27 +0000 (02:58 +0200)]
ipq806x: fix missing changes in 5.4 for new cpufreq implementation
The new cpufreq dedicated driver changed the node structure
on how the cache should be defined in the dts. The 5.4 dtsi addition
patch has not been updated to follow the new implementation.
Fix this to restore correct cache scaling and restore any performance
regression.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Hardware-Revision
-----------------
There are two board revisions of the RUT230, a v0 and v1.
A HW version is silkscreened on the top of the PCBs front side as well
as shown in the Teltonika UI. However, this looks to be a different
identifier, as the GPl dump shows this silkscreened / UI shown version
are internally treated identically.
Th following mapping has been obtained from the latest GPl dump.
HW Ver 01 - 04 --> v0
HW Ver > 05 --> v1
My board was a HW Ver 09 and is treated as a v1.
Installation
------------
While attaching power, hold down the reset button and release it after
the signal LEDs flashed 3 times.
Attach your Computer with the devices LAN port and assign yourself the
IPv4 address 192.168.1.10/24. Open a web browser, navigate to
192.168.1.1. Upload the OpenWrt factory image.
The device will install OpenWrt and automatically reboots afterwards.
You can use the smae procedure with the stock firmware to return back to
the vendor firmware.
Etan Kissling [Sun, 27 Jun 2021 22:02:46 +0000 (22:02 +0000)]
dnsmasq: distinct Ubus names for multiple instances
Currently, when using multiple dnsmasq instances they are all assigned
to the same Ubus instance name. This does not work, as only a single
instance can register with Ubus at a time. In the log, this leads to
`Cannot add object to UBus: Invalid argument` error messages.
Furthermore, upstream 3c93e8eb41952a9c91699386132d6fe83050e9be changes
behaviour so that instead of the log, dnsmasq exits at start instead.
With this patch, all dnsmasq instances are assigned unique names so that
they can register with Ubus concurrently. One of the enabled instances
is always assigned the previous default name "dnsmasq" to avoid breaking
backwards compatibility with other software relying on that default.
Previously, a random instance got assigned that name (while the others
produced error logs). Now, the first unnamed dnsmasq config section is
assigned the default name. If there are no unnamed dnsmasq sections the
first encountered named dnsmasq config section is assigned instead.
A similar issue exists for Dbus and was similarly addressed.
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
[tweaked commit message] dnsmasq was not crashing it is exiting Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bob Cantor [Thu, 24 Jun 2021 18:37:17 +0000 (04:37 +1000)]
base-files: wifi: swap the order of some ubus calls
"/sbin/wifi up" makes three ubus calls:
1. ubus call network reload
2. ubus call network.wireless down
3. ubus call network.wireless up
The first and third ubus calls call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel,
so the call sequence becomes,
This commit swaps the order of the first two ubus calls,
1. ubus call network.wireless down
2. ubus call network reload
3. ubus call network.wireless up
Consequently drv_mac80211_setup is only called once,
and two related bugs (#FS3784 and #FS3902) are no longer triggered
by /sbin/wifi.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
Bob Cantor [Thu, 24 Jun 2021 17:18:33 +0000 (03:18 +1000)]
mac80211: fix no_reload logic (FS#3902)
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete. But
"ubus call network.wireless status" erroneously reports that radio0 is down.)
This commit sets no_reload = 0 during the second call of drv_mac80211_setup.
It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.
When /sbin/wifi is used to turn on wifi,
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
/sbin/wifi makes the following ubus calls,
ubus call network reload
ubus call network.wireless down
ubus call network.wireless up
The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,
John Audia [Thu, 24 Jun 2021 11:51:55 +0000 (07:51 -0400)]
ipq806x: refresh config for kernel 5.4
* With kernel 5.4.128, ran: make kernel_menuconfig CONFIG_TARGET=generic
* Manually added back CONFIG_LEDS_TRIGGER_DISK=y so as not to revert f93fcf8923aa ("ipq806x: enable disk-activity LED trigger")
Signed-off-by: John Audia <graysky@archlinux.us>
[minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysntpd server becomes unavailable if the index of the bound
interface changes. So let's add an interface trigger to reload sysntpd.
This patch also adds the ability for the sysntpd script to handle
uci interface name from configuration.
Fixes: 4da60500ebd2 ("busybox: sysntpd: option to bind server to iface") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
The router itself is just a board with Power / USB / RJ-45 connectors
and DC/DC converters. The SoC and WiFi components are on a
daughterboard which connect using two M.2 connectors.
The compute module has the model number "T-CB1800K-DM2 V02" printed on
it. The main baord has "T-MB5EU V01" printed on it. This information
might be useful, as it's highly likely either of these two will be
reused in similar designs.
The router itself is sold as Tenbay T-MB5EU directly from the OEM as
well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a
slightly different case.
Installation
------------
A Tool for creating a factory image for the Vendor Web Interface can be
found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/
As the OEM Firmware is just a modified LEDE 17.01, you can also access
failsafe mode via UART while the OS boots, by connecting to UART
and pressing "f" when prompted. The Router is reachable at
192.168.1.1 via root without password.
Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade
using the -n and -F flags.
Alternatively, the board can be flashed by attaching to the UART
console, interrupting the boot process by keeping "0" pressed while
attaching power.
Serve the OpenWrt initramfs using a TFTP server with address
192.168.1.66. Rename the initramfs to ax1800.bin.
Attach your TFTP server to one of the LAN ports. Execute the following
commands.
Hans Dedecker [Sun, 27 Jun 2021 13:29:25 +0000 (15:29 +0200)]
glibc: update to latest 2.33 HEAD (BZ #27646, bug 27896, BZ #15271)
58b90461ae elf: Use _dl_catch_error from base namespace in dl-libc.c [BZ #27646] 8c06748c51 Fix use of __pthread_attr_copy in mq_notify (bug 27896) 4b6be914bd Use __pthread_attr_copy in mq_notify (bug 27896) f4cba6ca1e dlfcn: Failures after dlmopen should not terminate process [BZ #15271]
David Bauer [Mon, 14 Jun 2021 22:15:17 +0000 (00:15 +0200)]
ramips: fix AR8033 fiber operation
It was reported AR8033 did not work in fiber operation mode on the ER-X.
While the earlier attempt of fixing this mitigated the issue of 1000
Base-X link mode not being supported, it also switched to the copper
page, breaking fiber operation altogether.
Extend the hack adding fiber operation so it does not switch to the
copper page. Also remove the part where the supported link mode bit for
1000 Base-X is removed, as this is required for fiber operation.
David Bauer [Mon, 14 Jun 2021 21:53:38 +0000 (23:53 +0200)]
generic: at803x: mask 1000 Base-X link mode
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
lantiq: xrx200: switch the subtarget to the mainline DSA driver
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430 Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020 Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1 Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490 Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490 Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431) Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Etan Kissling [Sat, 26 Jun 2021 12:11:45 +0000 (12:11 +0000)]
dnsmasq: Update to version 2.86test3
Need this version to add config option for connmark DNS filtering.
Summary of upstream CHANGELOG:
* Handle DHCPREBIND requests in the DHCPv6 server code.
* Fix bug which caused dnsmasq to lose track of processes forked.
* Major rewrite of the DNS server and domain handling code.
* Revise resource handling for number of concurrent DNS queries.
* Improve efficiency of DNSSEC.
* Connection track mark based DNS query filtering.
ramips: ethernet: ralink: rewrite esw_rt3050 to support link states
Ensure the esw is initialized before the ethernet device is sending
packets. Further implement carrier detection similar to mt7620.
If any port has a link, the ethernet device will detect a carrier.
ramips: ethernet: ralink: add fe_reset_fe() to reset fe via reset controller
The dts defines the reset fe for all architectures. However
the soc code used direct register access of the reset controller.
Replace the custom soc reset with a generic fe_reset_fe().
Instead of assuming /sbin contains the correct BusyBox symlinks, directly invoke
the busybox executable. The required utilities are guaranteed to be present,
since the zram-swap package selects them. Additionally, don't assume busybox
resides in /bin, rely on PATH to find it.
While at it, update the copyright year, use SPDX and switch to AUTORELEASE.
Raphaël Mélotte [Wed, 7 Oct 2020 08:08:14 +0000 (10:08 +0200)]
hostapd: add default_disabled option to the supplicant
With the default configuration we generate, the supplicant starts
scanning and tries to connect to any open network when the interface
is enabled.
In some cases it can be desirable to prevent the supplicant from
scanning by itself. For example, if on the same radio an AP is
configured and an unconfigured STA is added (to be configured with
WPS), the AP might not be able to beacon until the STA stops
scanning.
In such a case, the STA configuration can still be required to set
specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to
"disabled" in uci (because that would prevent the supplicant from
being run at all). The alternative is to add the "disabled" parameter
to the default network block in the supplicant configuration.
This patch adds a "default_disabled" setting in UCI which, when set,
adds the "disabled" parameter to the supplicant default network block.
The system init script currently sets /tmp/localinfo when zoneinfo is
populated. However, zoneinfo has spaces in it whereas the actual files
have _ instead of spaces. This made the if condition never return true.
Example failure when removing the if condition:
/tmp/localtime -> /usr/share/zoneinfo/America/Los Angeles
This file does not exist. America/Los_Angeles does.
Liu Yu [Sat, 12 Jun 2021 12:02:45 +0000 (20:02 +0800)]
ramips: fix software reboot failure on HILINK HLK-7628N
In the new kernel version 5.X,reboot will fail.
When SOC is reset, flash has not exited the 4-byte address mode,
which causes the operation mode mismatch of flash during boot.Add
broken-flash-reset to make flash exit 4-byte address mode before
SOC reset
Michael Pratt [Tue, 20 Apr 2021 16:35:47 +0000 (12:35 -0400)]
ramips: mt7620: disable SOC VLANs for external switches
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617aecbd47debd4d3a734dc0e471342db96)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Michael Pratt [Mon, 31 May 2021 07:56:20 +0000 (03:56 -0400)]
ramips: mt7620: add ephy-disable option to switch driver
Add back the register write to disable internal PHYs
as a separate option in the code that can be set using a DTS property.
Set the option to true by default
when an external mt7530 switch is identified.
This makes the driver more in sync with original SDK code
while keeping the lines separated into different options
to accommodate any board with any PHY layout.
Michael Pratt [Sun, 30 May 2021 06:02:47 +0000 (02:02 -0400)]
ramips: mt7620: move mt7620_mdio_mode() to ethernet driver
The function mt7620_mdio_mode is only called once
and both the function and mdio_mode block have been named incorrectly,
leading to confusion and useless commits.
These lines in the mdio_mode block of mt7620_hw_init
are only intended for boards with an external mt7530 switch.
(see commit 194ca6127ee18cd3a95da4d03f02e43b5428c0bb)
Therefore, move lines from mdio_mode to the place in soc_mt7620.c
where the type of mt7530 switch is identified,
and move lines from mt7620_mdio_mode to a main function.
mt7620_mdio_mode was called from mt7620_gsw_init
where the priv struct is available,
so the lines must stay in mt7620_gsw_init function.
In order to keep things as simple as possible,
keep the DTS property related function calls together,
by moving them from mt7620_gsw_probe to init.
Remove the now useless DTS properties and extra phy nodes.
Fixes: 5a6229a93df8 ("ramips: remove superfluous & confusing DT binding") Fixes: b85fe43ec8c4 ("ramips: mt7620: add force use of mdio-mode") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Sat, 3 Apr 2021 18:42:51 +0000 (14:42 -0400)]
ramips: mt7620: use DTS to set PHY base address for external PHYs
Set the PHY base address to 12 for mt7530 and 8 for others,
which is based on the default setting for some devices
from printing the register with the following command
after it is written to by uboot during the boot cycle.
`md 0x10117014 1`
PHY_BASE option only uses 5 bits of the register,
bits 16 to 20, so use 8-bit integer type.
Set the option using the DTS property mediatek,ephy-base
and create the gsw node if missing.
Also, added a kernel message to display the EPHY base address.
Note:
If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf)
then there is adverse effects with Atheros switches.
Michael Pratt [Tue, 20 Apr 2021 22:45:15 +0000 (18:45 -0400)]
ramips: mt7620: allow both internal and external PHYs
When the new variable ephy_base was introduced,
it was not applied to the if block for mdio_mode.
The first line in the mdio_mode if block
sets the EPHY base address to 12 in the SOC by writing a register,
but the corresponding variable in the driver
was still set to the default of 0.
This causes subsequent lines that write registers with the function
_mt7620_mii_write
to write to PHY addresses 0 through 4
while internal PHYs have been moved to addresses 12 through 16.
All of these lines are intended only for PHYs on the SOC internal switch,
however, they are being written to external ethernet switches
if they exist at those PHY addresses 0 through 4.
This causes some ethernet ports to be broken on boards with AR8327 or QCA8337 switch.
Other suggested fixes move those lines to the else block of mdio_mode,
but removing the else block completely also fixes it.
Therefore, move the lines to the mt7620_hw_init function main block,
and have only one instance of the function mtk_switch_w32
for writing the register with the EPHY base address.
In theory, this also allows for boards that have both external switches
and internal PHYs that lead to ethernet ports to be supported.
Fixes: 391df3782914 ("ramips: mt7620: add EPHY base mdio address changing possibility") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 2 Jun 2021 03:01:26 +0000 (23:01 -0400)]
ramips: mt7620: fix ethernet driver GMAC port init
A workaround was added to the switch driver
to set SOC port 4 as an RGMII GMAC interface
based on the DTS property mediatek,port4-gmac.
(previously mediatek,port4)
However, the ethernet driver already does this,
but is being blocked by a return statement
whenever the phy-handle and fixed-link properties
are both missing from nodes that define the port properties.
Revert the workaround, so that both the switch driver
and ethernet driver are not doing the same thing
and move the phy-handle related lines down
so nothing is ending the function prematurely.
While at it, clean up kernel messages
and delete useless return statements.
Fixes: f6d81e2fa1f1 ("mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Fri, 11 Jun 2021 18:54:43 +0000 (14:54 -0400)]
ramips: mt7620: remove useless GMAC nodes
These nodes are used for configuring a GMAC interface
and for defining external PHYs to be accessed with MDIO.
None of this is possible on MT7620N, only MT7620A,
so remove them from all MT7620N DTS.
When the mdio-bus node is missing, the driver returns -NODEV
which causes the internal switch to not initialize.
Replace that return so that everything works without the DTS node.
Also, an extra kernel message to indicate for all error conditions
that mdio-bus is disabled.
Fixes: d482356322c9 ("ramips: mt7620n: add mdio node and disable port4 by default") Fixes: aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Let the DTS property be boolean instead of string
where EPHY mode is the default.
Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.
Hauke Mehrtens [Mon, 21 Jun 2021 22:45:21 +0000 (00:45 +0200)]
realtek: Fix failsafe mode
The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is
configured. Do not use the standard failsafe configuration for DSA
accessing the default port directly, but configure a switch on the lan1
interface instead.
This will add the VLAN ID 1 configuration to the switch:
$ bridge vlan show
port vlan-id
lan1 1 PVID Egress Untagged
switch 1 PVID Egress Untagged
These are the latest patches that just landed upstream for 5.13, will be
backported by Greg into 5.10 (because of stable@), and are now in the
5.4 backport branch of wireguard: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Stijn Segers <foss@volatilesystems.org>
Birger Koblitz [Sun, 6 Jun 2021 14:20:59 +0000 (16:20 +0200)]
realtek: Fix buffer length calculation on RTL8380 with CRC offload
Fixes the buffer and packet length calculations for Ethernet TX on
the RTL8380 SoC when CRC calculation offload is enabled.
CRC-offload is always done by the SoC, but additional CRC
calculation was previously done also by the kernel.
It also fixes detection of the DSA tag for packets on RTL8390
SoCs for ports > 28.
Timo Sigurdsson [Tue, 15 Jun 2021 21:09:41 +0000 (23:09 +0200)]
hostapd: make wnm_sleep_mode_no_keys configurable
In the aftermath of the KRACK attacks, hostapd gained an AP-side workaround
against WNM-Sleep Mode GTK/IGTK reinstallation attacks. WNM Sleep Mode is not
enabled by default on OpenWrt, but it is configurable through the option
wnm_sleep_mode. Thus, make the AP-side workaround configurable as well by
exposing the option wnm_sleep_mode_no_keys. If you use the option
wpa_disable_eapol_key_retries and have wnm_sleep_mode enabled, you might
consider using this workaround.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Karel Kočí [Mon, 7 Jun 2021 17:25:06 +0000 (19:25 +0200)]
base-files: fix enabled for services with only STOP
There are services that have only STOP value set. They are executed only
on shutdown and it is common to use them for system cleanup. There is
one such service shipped directly with base-files, it is 'umount'. Those
work the same way as those with START but enabled does not report them
as enabled although it should have as they can be enabled and disabled
as any other service.
This also changes check from check for executable to check for symbolic
link. The implementation depends on those being links to service file
and it is much cleaner and direct to check for them being links.
Timo Sigurdsson [Tue, 15 Jun 2021 21:12:08 +0000 (23:12 +0200)]
hostapd: fix handling of the channel utilization options
Commit 0a7657c ("hostapd: add channel utilization as config option") added the
two new uci options bss_load_update_period and chan_util_avg_period. However,
the corresponding "config_add_int" calls for these options weren't added, so
attempting to actually use these options and change their values is bound to
fail - they always stay at their defaults. Add the missing code to actually
make these options work.
Fixes: 0a7657c ("hostapd: add channel utilization as config option") Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Timo Sigurdsson [Tue, 15 Jun 2021 21:08:56 +0000 (23:08 +0200)]
hostapd: make country3 option configurable
The country3 option in hostapd.conf allows the third octet of the country
string to be set. It can be used e.g. to indicate indoor or outdoor use (see
hostapd.conf for further details). Make this option configurable but optional
in OpenWrt.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Karel Kočí [Mon, 21 Jun 2021 09:42:25 +0000 (11:42 +0200)]
ustream-ssl: variants conflict with each other
This adds conflicts between variants of libustream pacakge.
They provide the same file and thus it should not be possible to install
them side by side.
Chris Blake [Tue, 15 Jun 2021 13:03:05 +0000 (08:03 -0500)]
kernel/modules: make sure igb loads at boot
Without loading the igb at boot, the recovery wouldn't have
network available. All network drivers should be loaded before
etc/board.d/02_network is called. Note that other network drivers
already have this set, such as tg3.
Paul Spooren [Thu, 17 Jun 2021 04:05:04 +0000 (18:05 -1000)]
build: create profiles.json per default
The file is a info file just like config.buildinfo, feeds.buildinfo and
version.buildinfo. It bundles these and more information in a machine
readable way.
This commit enables the creation of profiles.json by default and not
only for buildbots. By doing so it follow the behaviour of the
ImageBuilder which always creates the file, lastly this increases the
files visibility for downstream projects.
Koen Vandeputte [Mon, 17 May 2021 15:52:53 +0000 (17:52 +0200)]
ath79: ar934x: fix mounting issues if subpage is not supported
Currently, the option to disable subpage writing is only set
when a HW ECC engine is used.
Some boards lack a HW ECC engine and use software for that.
In this case, this NAND option does not get set when the NAND chip
does not support it, resulting in mounting errors.
Move the setting of this option to a generic init location so it
gets set for all types where required.
While at it, also OR the option instead of just setting it
so we don't overwrite potential flags being set somewhere else.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
port -- both can be used for LTE modem, but only one can be
used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
(tested with sysfs led trigger timer). But kmod-gpio-beeper
doesn't work -- we left this as is for now.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Florian Eckert [Mon, 1 Feb 2021 10:02:30 +0000 (11:02 +0100)]
base-files: add syslog logging for v function
The logging output should not only be displayed in the calling shell
session but also in the syslog. A sysupgrade and a configuration
import, export can thus be traced in the syslog.
Chuck Fan [Tue, 9 Mar 2021 09:42:57 +0000 (17:42 +0800)]
base-files: upgrade: use zcat command provided by busybox
Calling `switch_to_ramfs()` will not copy the gzip executable
(/bin/gzip) to ramfs, but `/bin/zcat` will call `/bin/gzip` when
package gzip is installed, instead of the busybox-supplied zcat.
This will cause `zcat` to fail to find `gzip`, then cause the
sysupgrade to fail. Adding the `busybox` prefix here will solve
the problem.
projects / thirdparty / openwrt.git / log
