When the gpio-addr-flash.c driver was merged with physmap-core.c the
code to store the current gpio_values was lost. This meant that once a
gpio was asserted it was never de-asserted. Fix this by storing the
current offset in gpio_values like the old driver used to.
Fixes: commit ba32ce95cbd9 ("mtd: maps: Merge gpio-addr-flash.c into physmap-core.c") Cc: <stable@vger.kernel.org> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed that reads crossing 4K address boundary are failing.
This limitation is mentioned in Intel documents:
Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:
"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."
Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):
"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."
Avoid this by splitting an operation crossing the boundary into two
operations.
Fixes: 8afda8b26d01 ("spi-nor: Add support for Intel SPI serial flash controller") Cc: stable@vger.kernel.org Reported-by: Romain Porte <romain.porte@nokia.com> Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mismatch between what is found in the Datasheets for DA9063 and DA9063L
provided by Dialog Semiconductor, and the register names provided in the
MFD registers file. The changes are for the OTP (one-time-programming)
control registers. The two naming errors are OPT instead of OTP, and
COUNT instead of CONT (i.e. control).
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that recently multiple systems (chromebooks) couldn't wake
from S0ix using LID or Keyboard after updating to a newer kernel. I
bisected and it turned up commit f941d3e41da7 ("ACPI: EC / PM: Disable
non-wakeup GPEs for suspend-to-idle"). I checked that the issue got
fixed if that commit was reverted.
I debugged and found that although PNP0C0D:00 (representing the LID)
is wake capable and should wakeup the system per the code in
acpi_wakeup_gpe_init() and in drivers/acpi/button.c:
On debugging, I found that its corresponding GPE is not being enabled.
The particular GPE's "gpe_register_info->enable_for_wake" does not
have any bits set when acpi_enable_all_wakeup_gpes() comes around to
use it. I looked at code and could not find any other code path that
should set the bits in "enable_for_wake" bitmask for the wake enabled
devices for s2idle. [I do see that it happens for S3 in
acpi_sleep_prepare()].
Thus I used the same call to enable the GPEs for wake enabled devices,
and verified that this fixes the regression I was seeing on multiple
of my devices.
[ rjw: The problem is that commit f941d3e41da7 ("ACPI: EC / PM:
Disable non-wakeup GPEs for suspend-to-idle") forgot to add
the acpi_enable_wakeup_devices() call for s2idle along with
acpi_enable_all_wakeup_gpes(). ]
Fixes: f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") Link: https://bugzilla.kernel.org/show_bug.cgi?id=203579 Signed-off-by: Rajat Jain <rajatja@google.com>
[ rjw: Subject & changelog ] Cc: 5.0+ <stable@vger.kernel.org> # 5.0+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The task structure is freed while get_mem_cgroup_from_mm() holds
rcu_read_lock() and dereferences mm->owner.
get_mem_cgroup_from_mm() failing fork()
---- ---
task = mm->owner
mm->owner = NULL;
free(task)
if (task) *task; /* use after free */
The fix consists in freeing the task with RCU also in the fork failure
case, exactly like it always happens for the regular exit(2) path. That
is enough to make the rcu_read_lock hold in get_mem_cgroup_from_mm()
(left side above) effective to avoid a use after free when dereferencing
the task structure.
An alternate possible fix would be to defer the delivery of the
userfaultfd contexts to the monitor until after fork() is guaranteed to
succeed. Such a change would require more changes because it would
create a strict ordering dependency where the uffd methods would need to
be called beyond the last potentially failing branch in order to be
safe. This solution as opposed only adds the dependency to common code
to set mm->owner to NULL and to free the task struct that was pointed by
mm->owner with RCU, if fork ends up failing. The userfaultfd methods
can still be called anywhere during the fork runtime and the monitor
will keep discarding orphaned "mm" coming from failed forks in userland.
This race condition couldn't trigger if CONFIG_MEMCG was set =n at build
time.
[aarcange@redhat.com: improve changelog, reduce #ifdefs per Michal] Link: http://lkml.kernel.org/r/20190429035752.4508-1-aarcange@redhat.com Link: http://lkml.kernel.org/r/20190325225636.11635-2-aarcange@redhat.com Fixes: 893e26e61d04 ("userfaultfd: non-cooperative: Add fork() event") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Tested-by: zhong jiang <zhongjiang@huawei.com> Reported-by: syzbot+cbb52e396df3e565ab02@syzkaller.appspotmail.com Cc: Oleg Nesterov <oleg@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: zhong jiang <zhongjiang@huawei.com> Cc: syzbot+cbb52e396df3e565ab02@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, ocfs2_iget() reads the data of inode, which has been
deleted for some reason. That will make the system panic. So We should
judge whether this inode has been deleted, and tell the caller that the
inode is a bad inode.
For example, the ocfs2 is used as the backed of nfs, and the client is
nfsv3. This issue can be reproduced by the following steps.
on the nfs server side,
..../patha/pathb
Step 1: The process A was scheduled before calling the function fh_verify.
Step 2: The process B is removing the 'pathb', and just completed the call
to function dput. Then the dentry of 'pathb' has been deleted from the
dcache, and all ancestors have been deleted also. The relationship of
dentry and inode was deleted through the function hlist_del_init. The
following is the call stack.
dentry_iput->hlist_del_init(&dentry->d_u.d_alias)
At this time, the inode is still in the dcache.
Step 3: The process A call the function ocfs2_get_dentry, which get the
inode from dcache. Then the refcount of inode is 1. The following is the
call stack.
nfsd3_proc_getacl->fh_verify->exportfs_decode_fh->fh_to_dentry(ocfs2_get_dentry)
Step 4: Dirty pages are flushed by bdi threads. So the inode of 'patha'
is evicted, and this directory was deleted. But the inode of 'pathb'
can't be evicted, because the refcount of the inode was 1.
Step 5: The process A keep running, and call the function
reconnect_path(in exportfs_decode_fh), which call function
ocfs2_get_parent of ocfs2. Get the block number of parent
directory(patha) by the name of ... Then read the data from disk by the
block number. But this inode has been deleted, so the system panic.
Process A Process B
1. in nfsd3_proc_getacl |
2. | dput
3. fh_to_dentry(ocfs2_get_dentry) |
4. bdi flush dirty cache |
5. ocfs2_iget |
[283465.542049] OCFS2: ERROR (device sdp): ocfs2_validate_inode_block:
Invalid dinode #580640: OCFS2_VALID_FL not set
[283465.545490] Kernel panic - not syncing: OCFS2: (device sdp): panic forced
after error
hugetlb uses a fault mutex hash table to prevent page faults of the
same pages concurrently. The key for shared and private mappings is
different. Shared keys off address_space and file index. Private keys
off mm and virtual address. Consider a private mappings of a populated
hugetlbfs file. A fault will map the page from the file and if needed
do a COW to map a writable page.
Hugetlbfs hole punch uses the fault mutex to prevent mappings of file
pages. It uses the address_space file index key. However, private
mappings will use a different key and could race with this code to map
the file page. This causes problems (BUG) for the page cache remove
code as it expects the page to be unmapped. A sample stack is:
There seems to be another potential COW issue/race with this approach
of different private and shared keys as noted in commit 8382d914ebf7
("mm, hugetlb: improve page-fault scalability").
Since every hugetlb mapping (even anon and private) is actually a file
mapping, just use the address_space index key for all mappings. This
results in potentially more hash collisions. However, this should not
be the common case.
Link: http://lkml.kernel.org/r/20190328234704.27083-3-mike.kravetz@oracle.com Link: http://lkml.kernel.org/r/20190412165235.t4sscoujczfhuiyt@linux-r8p5 Fixes: b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by: Davidlohr Bueso <dbueso@suse.de> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dtor returned by get_compound_page_dtor in __put_compound_page may be
the function of free_huge_page which will lock the hugetlb_lock, so don't
put_page in lock of hugetlb_lock.
Link: http://lkml.kernel.org/r/b8ade452-2d6b-0372-32c2-703644032b47@huawei.com Fixes: 9980d744a0 ("mm, hugetlb: get rid of surplus page accounting tricks") Signed-off-by: Kai Shen <shenkai8@huawei.com> Signed-off-by: Feilong Lin <linfeilong@huawei.com> Reported-by: Wang Wang <wangwang2@huawei.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with c6f3c5ee40c1 ("mm/huge_memory.c: fix modifying of page
protection by insert_pfn_pmd()") vmf_insert_pfn_pmd() internally calls
pmdp_set_access_flags(). That helper enforces a pmd aligned @address
argument via VM_BUG_ON() assertion.
Update the implementation to take a 'struct vm_fault' argument directly
and apply the address alignment fixup internally to fix crash signatures
like:
The semantics of what mincore() considers to be resident is not
completely clear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache".
That's potentially a problem, as that [in]directly exposes
meta-information about pagecache / memory mapping state even about
memory not strictly belonging to the process executing the syscall,
opening possibilities for sidechannel attacks.
Change the semantics of mincore() so that it only reveals pagecache
information for non-anonymous mappings that belog to files that the
calling process could (if it tried to) successfully open for writing;
otherwise we'd be including shared non-exclusive mappings, which
- is the sidechannel
- is not the usecase for mincore(), as that's primarily used for data,
not (shared) text
[jkosina@suse.cz: v2] Link: http://lkml.kernel.org/r/20190312141708.6652-2-vbabka@suse.cz
[mhocko@suse.com: restructure can_do_mincore() conditions] Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1903062342020.19912@cbobk.fhfr.pm Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Josh Snyder <joshs@netflix.com> Acked-by: Michal Hocko <mhocko@suse.com> Originally-by: Linus Torvalds <torvalds@linux-foundation.org> Originally-by: Dominique Martinet <asmadeus@codewreck.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Chinner <david@fromorbit.com> Cc: Kevin Easton <kevin@guarana.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Cyril Hrubis <chrubis@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Daniel Gruss <daniel@gruss.cc> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in order to support cryptocell tee fips error that may occurs while
cryptocell ree is suspended, an cc_tee_handle_fips_error call added
to the cc_pm_resume function.
Adds function that checks if cryptocell tee fips error occurred
and in such case triggers system error through kernel panic.
Change fips function to use this new routine.
During power management suspend the driver need to prepare the device
for the power down operation and as a last indication write to the
HOST_POWER_DOWN_EN register which signals to the hardware that
The ccree is ready for power down.
We were computing the size of the import buffer based on the digest size
but the 318 and 224 byte variants use 512 and 256 bytes internal state
sizes respectfully, thus causing the import buffer to overrun.
We were handling chained scattergather lists with specialized code
needlessly as the regular sg APIs handle them just fine. The code
handling this also had an (unused) code path with a use-before-init
error, flagged by Coverity.
Remove all special handling of chained sg and leave their handling
to the regular sg APIs.
Prefetch-with-intent-to-write is currently part of the XADD mapping in
the AArch64 JIT and follows the kernel's implementation of atomic_add.
This may interfere with other threads executing the LDXR/STXR loop,
leading to potential starvation and fairness issues. Drop the optional
prefetch instruction.
Fixes: 85f68fe89832 ("bpf, arm64: implement jiting of BPF_XADD") Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In resume from S3, HDAC HDMI codec driver dapm event callback may be
operated before HDMI codec driver turns on the display audio power
domain because of the contest between display driver and hdmi codec driver.
This patch adds the device_link between soc card device (consumer) and
hdmi codec device (supplier) to make sure the sequence is always correct.
Signed-off-by: Libin Yang <libin.yang@intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.
Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org> Reviewed-by: Ben Zhang <benzh@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max98090 driver defines 3 DAPM muxes; one for the right line output
(LINMOD Mux), one for the left headphone mixer source (MIXHPLSEL Mux)
and one for the right headphone mixer source (MIXHPRSEL Mux). The same
bit is used for the mux as well as the DAPM enable, and although the mux
can be correctly configured, after playback has completed, the mux will
be reset during the disable phase. This is preventing the state of these
muxes from being saved and restored correctly on system reboot. Fix this
by marking these muxes as SND_SOC_NOPM.
Note this has been verified this on the Tegra124 Nyan Big which features
the MAX98090 codec.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the System76 Gazelle (gaze14), there is a headset microphone input
attached to 0x1a that does not have a jack detect. In order to get it
working, the pin configuration needs to be set correctly, and the
ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied. This is
identical to the patch already applied for the System76 Darter Pro
(darp5).
[ NOTE: This change is supposed to reduce the possible click noises at
(runtime) PM resume. The functionality should be same (i.e. the
verbs are executed correctly) no matter which order is, so this
should be safe to apply for all codecs -- tiwai ]
On the machines with AMD GPU or Nvidia GPU, we often meet this issue:
after s3, there are 4 HDMI/DP audio devices in the gnome-sound-setting
even there is no any monitors plugged.
When this problem happens, we check the /proc/asound/cardX/eld#N.M, we
will find the monitor_present=1, eld_valid=0.
The root cause is BIOS or GPU driver makes the PRESENCE valid even no
monitor plugged, and of course the driver will not get the valid
eld_data subsequently.
In this situation, we should not report the jack_plugged event, to do
so, let us change the function hdmi_present_sense_via_verbs(). In this
function, it reads the pin_sense via snd_hda_pin_sense(), after
calling this function, the jack_dirty is 0, and before exiting
via_verbs(), we change the shadow pin_sense according to both
monitor_present and eld_valid, then in the snd_hda_jack_report_sync(),
since the jack_dirty is still 0, it will report jack event according
to this modified shadow pin_sense.
After this change, the driver will not report Jack_is_plugged event
through hdmi_present_sense_via_verbs() if monitor_present is 1 and
eld_valid is 0.
The driver will check the monitor presence when resuming from suspend,
starting poll or interrupt triggers. In these 3 situations, the
jack_dirty will be set to 1 first, then the hda_jack.c reads the
pin_sense from register, after reading the register, the jack_dirty
will be set to 0. But hdmi_repoll_work() is enabled in these 3
situations, It will read the pin_sense a couple of times subsequently,
since the jack_dirty is 0 now, It does not read the register anymore,
instead it uses the shadow pin_sense which is read at the first time.
It is meaningless to check the shadow pin_sense a couple of times,
we need to read the register to check the real plugging state, so
we set the jack_dirty to 1 in the hdmi_repoll_work().
In parse_audio_selector_unit(), the string array 'namelist' is allocated
through kmalloc_array(), and each string pointer in this array, i.e.,
'namelist[]', is allocated through kmalloc() in the following for loop.
Then, a control instance 'kctl' is created by invoking snd_ctl_new1(). If
an error occurs during the creation process, the string array 'namelist',
including all string pointers in the array 'namelist[]', should be freed,
before the error code ENOMEM is returned. However, the current code does
not free 'namelist[]', resulting in memory leaks.
To fix the above issue, free all string pointers 'namelist[]' in a loop.
The line6 toneport driver has code for some delayed initialization,
and this hits the kernel Oops because mutex and other sleepable
functions are used in the timer callback. Fix the abuse by a delayed
work instead so that everything works gracefully.
Some time ago, a fix was done for the sdhci-acpi driver, refer
commit 6e1c7d6103fe ("mmc: sdhci-acpi: Reduce Baytrail eMMC/SD/SDIO
hangs"). The same issue was not expected to affect the sdhci-pci driver,
but there have been reports to the contrary, so make the same hardware
setting change.
This patch applies to v5.0+ but before that backports will be required.
The tag set is allocated in mmc_init_queue but never freed. This results
in a memory leak. This change makes sure we free the tag set when the
queue is also freed.
ddr_signaling is set to true for DDR50 and DDR52 modes but is
not set back to false for other modes. This programs incorrect
host clock when mode change happens from DDR52/DDR50 to other
SDR or HS modes like incase of mmc_retune where it switches
from HS400 to HS DDR and then from HS DDR to HS mode and then
to HS200.
This patch fixes the ddr_signaling to set properly for non DDR
modes.
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
xts-aes-neonbs doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and unconditionally accessing walk.iv has caused a
real problem in other algorithms. Thus, update xts-aes-neonbs to start
checking the return value of skcipher_walk_virt().
Fixes: 1abee99eafab ("crypto: arm64/aes - reimplement bit-sliced ARM/NEON implementation for arm64") Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
arm32 xts-aes-neonbs doesn't set an alignmask, so currently it isn't
affected by this despite unconditionally accessing walk.iv. However
this is more subtle than desired, and it was actually broken prior to
the alignmask being removed by commit cc477bf64573 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"). Thus, update xts-aes-neonbs to
start checking the return value of skcipher_walk_virt().
Fixes: e4e7f10bfc40 ("ARM: add support for bit sliced AES using NEON instructions") Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 307244452d3d ("crypto: caam - generate hash keys in-place")
fixed ahash implementation in caam/jr driver such that user-provided key
buffer is not DMA mapped, since it's not guaranteed to be DMAable.
Apply a similar fix for caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+ Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commits c19650d6ea99 ("crypto: caam - fix DMA mapping of stack memory")
and 65055e210884 ("crypto: caam - fix hash context DMA unmap size")
fixed the ahash implementation in caam/jr driver such that req->result
is not DMA-mapped (since it's not guaranteed to be DMA-able).
Apply a similar fix for ahash implementation in caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+ Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 04e6d25c5bb2 ("crypto: caam - fix zero-length buffer DMA mapping")
fixed an issue in caam/jr driver where ahash implementation was
DMA mapping a zero-length buffer.
Current commit applies a similar fix for caam/qi2 driver.
Cc: <stable@vger.kernel.org> # v4.20+ Fixes: 3f16f6c9d632 ("crypto: caam/qi2 - add support for ahash algorithms") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kernel Crypto API request output the next IV data to
IV buffer for CBC implementation. So the last block data of
ciphertext should be copid into assigned IV buffer.
Reported-by: Eric Biggers <ebiggers@google.com> Fixes: 433cd2c617bf ("crypto: rockchip - add crypto driver for rk3288") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Zhang Zhijie <zhangzj@rock-chips.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCM instances can be created by either the "gcm" template, which only
allows choosing the block cipher, e.g. "gcm(aes)"; or by "gcm_base",
which allows choosing the ctr and ghash implementations, e.g.
"gcm_base(ctr(aes-generic),ghash-generic)".
However, a "gcm_base" instance prevents a "gcm" instance from being
registered using the same implementations. Nor will the instance be
found by lookups of "gcm". This can be used as a denial of service.
Moreover, "gcm_base" instances are never tested by the crypto
self-tests, even if there are compatible "gcm" tests.
The root cause of these problems is that instances of the two templates
use different cra_names. Therefore, fix these problems by making
"gcm_base" instances set the same cra_name as "gcm" instances, e.g.
"gcm(aes)" instead of "gcm_base(ctr(aes-generic),ghash-generic)".
This requires extracting the block cipher name from the name of the ctr
algorithm. It also requires starting to verify that the algorithms are
really ctr and ghash, not something else entirely. But it would be
bizarre if anyone were actually using non-gcm-compatible algorithms with
gcm_base, so this shouldn't break anyone in practice.
The arm64 gcm-aes-ce algorithm is failing the extra crypto self-tests
following my patches to test the !may_use_simd() code paths, which
previously were untested. The problem is that in the !may_use_simd()
case, an odd number of AES blocks can be processed within each step of
the skcipher_walk. However, the skcipher_walk is being done with a
"stride" of 2 blocks and is advanced by an even number of blocks after
each step. This causes the encryption to produce the wrong ciphertext
and authentication tag, and causes the decryption to incorrectly fail.
Fix it by only processing an even number of blocks per step.
Fixes: c2b24c36e0a3 ("crypto: arm64/aes-gcm-ce - fix scatterwalk API violation") Fixes: 71e52c278c54 ("crypto: arm64/aes-ce-gcm - operate on two input blocks at a time") Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->digest() method of crct10dif-pclmul reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
Fixes: 0b95a7f85718 ("crypto: crct10dif - Glue code to cast accelerated CRCT10DIF assembly as a crypto transform") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->digest() method of crct10dif-generic reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: 2d31e518a428 ("crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skcipher_walk_done() assumes it's a bug if, after the "slow" path is
executed where the next chunk of data is processed via a bounce buffer,
the algorithm says it didn't process all bytes. Thus it WARNs on this.
However, this can happen legitimately when the message needs to be
evenly divisible into "blocks" but isn't, and the algorithm has a
'walksize' greater than the block size. For example, ecb-aes-neonbs
sets 'walksize' to 128 bytes and only supports messages evenly divisible
into 16-byte blocks. If, say, 17 message bytes remain but they straddle
scatterlist elements, the skcipher_walk code will take the "slow" path
and pass the algorithm all 17 bytes in the bounce buffer. But the
algorithm will only be able to process 16 bytes, triggering the WARN.
Fix this by just removing the WARN_ON(). Returning -EINVAL, as the code
already does, is the right behavior.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: b286d8b1a690 ("crypto: skcipher - Add skcipher walk interface") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original assembly imported from OpenSSL has two copy-paste
errors in handling CTR mode. When dealing with a 2 or 3 block tail,
the code branches to the CBC decryption exit path, rather than to
the CTR exit path.
This leads to corruption of the IV, which leads to subsequent blocks
being corrupted.
This can be detected with libkcapi test suite, which is available at
https://github.com/smuellerDD/libkcapi
Reported-by: Ondrej Mosnáček <omosnacek@gmail.com> Fixes: 5c380d623ed3 ("crypto: vmx - Add support for VMS instructions by ASM") Cc: stable@vger.kernel.org Signed-off-by: Daniel Axtens <dja@axtens.net> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we free the psp_master if the PLATFORM_INIT fails during the
SEV FW probe. If psp_master is freed then driver does not invoke the PSP
FW. As per SEV FW spec, there are several commands (PLATFORM_RESET,
PLATFORM_STATUS, GET_ID etc) which can be executed in the UNINIT state
We should not free the psp_master when PLATFORM_INIT fails.
Fixes: 200664d5237f ("crypto: ccp: Add SEV support") Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Gary Hook <gary.hook@amd.com> Cc: stable@vger.kernel.org # 4.19.y Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the rfc7539 template is instantiated with specific implementations,
e.g. "rfc7539(chacha20-generic,poly1305-generic)" rather than
"rfc7539(chacha20,poly1305)", then the implementation names end up
included in the instance's cra_name. This is incorrect because it then
prevents all users from allocating "rfc7539(chacha20,poly1305)", if the
highest priority implementations of chacha20 and poly1305 were selected.
Also, the self-tests aren't run on an instance allocated in this way.
Fix it by setting the instance's cra_name from the underlying
algorithms' actual cra_names, rather than from the requested names.
This matches what other templates do.
Fixes: 71ebc4d1b27d ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539") Cc: <stable@vger.kernel.org> # v4.2+ Cc: Martin Willi <martin@strongswan.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm64 implementations of ChaCha and XChaCha are failing the extra
crypto self-tests following my patches to test the !may_use_simd() code
paths, which previously were untested. The problem is as follows:
When !may_use_simd(), the arm64 NEON implementations fall back to the
generic implementation, which uses the skcipher_walk API to iterate
through the src/dst scatterlists. Due to how the skcipher_walk API
works, walk.stride is set from the skcipher_alg actually being used,
which in this case is the arm64 NEON algorithm. Thus walk.stride is
5*CHACHA_BLOCK_SIZE, not CHACHA_BLOCK_SIZE.
This unnecessarily large stride shouldn't cause an actual problem.
However, the generic implementation computes round_down(nbytes,
walk.stride). round_down() assumes the round amount is a power of 2,
which 5*CHACHA_BLOCK_SIZE is not, so it gives the wrong result.
This causes the following case in skcipher_walk_done() to be hit,
causing a WARN() and failing the encryption operation:
if (WARN_ON(err)) {
/* unexpected case; didn't process all bytes */
err = -EINVAL;
goto finish;
}
Fix it by rounding down to CHACHA_BLOCK_SIZE instead of walk.stride.
(Or we could replace round_down() with rounddown(), but that would add a
slow division operation every time, which I think we should avoid.)
Fixes: 2fe55987b262 ("crypto: arm64/chacha - use combined SIMD/ALU routine for more speed") Cc: <stable@vger.kernel.org> # v5.0+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
Fix this in the LRW template by checking the return value of
skcipher_walk_virt().
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation. When the extra
self-tests were run on a KASAN-enabled kernel, a KASAN use-after-free
splat occured during lrw(aes) testing.
Fixes: c778f96bf347 ("crypto: lrw - Optimize tweak computation") Cc: <stable@vger.kernel.org> # v4.20+ Cc: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
salsa20-generic doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and it was actually broken prior to the alignmask
being removed by commit b62b3db76f73 ("crypto: salsa20-generic - cleanup
and convert to skcipher API").
Since salsa20-generic does not update the IV and does not need any IV
alignment, update it to use req->iv instead of walk.iv.
Currently, crypto4xx CFB and OFB AES ciphers are
failing testmgr's test vectors.
|cfb-aes-ppc4xx encryption overran dst buffer on test vector 3, cfg="in-place"
|ofb-aes-ppc4xx encryption overran dst buffer on test vector 1, cfg="in-place"
This is because of a very subtile "bug" in the hardware that
gets indirectly mentioned in 18.1.3.5 Encryption/Decryption
of the hardware spec:
the OFB and CFB modes for AES are listed there as operation
modes for >>> "Block ciphers" <<<. Which kind of makes sense,
but we would like them to be considered as stream ciphers just
like the CTR mode.
To workaround this issue and stop the hardware from causing
"overran dst buffer" on crypttexts that are not a multiple
of 16 (AES_BLOCK_SIZE), we force the driver to use the scatter
buffers as the go-between.
As a bonus this patch also kills redundant pd_uinfo->num_gd
and pd_uinfo->num_sd setters since the value has already been
set before.
Cc: stable@vger.kernel.org Fixes: f2a13e7cba9e ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8efd972ef96a ("crypto: testmgr - support checking skcipher output IV")
caused the crypto4xx driver to produce the following error:
| ctr-aes-ppc4xx encryption test failed (wrong output IV)
| on test vector 0, cfg="in-place"
This patch fixes this by reworking the crypto4xx_setkey_aes()
function to:
- not save the iv for ECB (as per 18.2.38 CRYP0_SA_CMD_0:
"This bit mut be cleared for DES ECB mode or AES ECB mode,
when no IV is used.")
- instruct the hardware to save the generated IV for all
other modes of operations that have IV and then supply
it back to the callee in pretty much the same way as we
do it for cbc-aes already.
- make it clear that the DIR_(IN|OUT)BOUND is the important
bit that tells the hardware to encrypt or decrypt the data.
(this is cosmetic - but it hopefully prevents me from
getting confused again).
- don't load any bogus hash when we don't use any hash
operation to begin with.
Cc: stable@vger.kernel.org Fixes: f2a13e7cba9e ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD family 17h Models 10h-2Fh may report a high number of L1 BTB MCA
errors under certain conditions. The errors are benign and can safely be
ignored. However, the high error rate may cause the MCA threshold
counter to overflow causing a high rate of thresholding interrupts.
In addition, users may see the errors reported through the AMD MCE
decoder module, even with the interrupt disabled, due to MCA polling.
Clear the "Counter Present" bit in the Instruction Fetch bank's
MCA_MISC0 register. This will prevent enabling MCA thresholding on this
bank which will prevent the high interrupt rate due to this error.
Define an AMD-specific function to filter these errors from the MCE
event pool so that they don't get reported during early boot.
Rename filter function in EDAC/mce_amd to avoid a naming conflict, while
at it.
[ bp: Move function prototype to the internal header and
massage/cleanup, fix typos. ]
Reported-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "clemej@gmail.com" <clemej@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Morse <james.morse@arm.com> Cc: Kees Cook <keescook@chromium.org> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Pu Wen <puwen@hygon.cn> Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Cc: Shirish S <Shirish.S@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: x86-ml <x86@kernel.org> Cc: <stable@vger.kernel.org> # 5.0.x: c95b323dcd35: x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models Cc: <stable@vger.kernel.org> # 5.0.x: 30aa3d26edb0: x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk Cc: <stable@vger.kernel.org> # 5.0.x: 9308fd407455: x86/MCE: Group AMD function prototypes in <asm/mce.h> Cc: <stable@vger.kernel.org> # 5.0.x Link: https://lkml.kernel.org/r/20190325163410.171021-2-Yazen.Ghannam@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC4_MISC thresholding quirk needs to be applied during S5 -> S0 and
S3 -> S0 state transitions, which follow different code paths. Carve it
out into a separate function and call it mce_amd_feature_init() where
the two code paths of the state transitions converge.
[ bp: massage commit message and the carved out function. ]
Some systems may report spurious MCA errors. In general, spurious MCA
errors may be disabled by clearing a particular bit in MCA_CTL. However,
clearing a bit in MCA_CTL may not be recommended for some errors, so the
only option is to ignore them.
An MCA error is printed and handled after it has been added to the MCE
event pool. So an MCA error can be ignored by not adding it to that pool
in the first place.
Add such a filtering function.
[ bp: Move function prototype to the internal header and massage. ]
2c7577a75837 ("sched/x86_64: Don't save flags on context switch")
Specifically because SMAP uses FLAGS.AC which invalidates the claim
that the kernel has clean flags.
In particular; while preemption from interrupt return is fine (the
IRET frame on the exception stack contains FLAGS) it breaks any code
that does synchonous scheduling, including preempt_enable().
This has become a significant issue ever since commit:
5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses")
provided for means of having 'normal' C code between STAC / CLAC,
exposing the FLAGS.AC state. So far this hasn't led to trouble,
however fix it before it comes apart.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org Fixes: 5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the CPU comes out of suspend, the firmware may have modified the OS
Double Lock Register. Save it in an unused slot of cpu_suspend_ctx, and
restore it on resume.
Currently, compat tasks running on arm64 can allocate memory up to
TASK_SIZE_32 (UL(0x100000000)).
This means that mmap() allocations, if we treat them as returning an
array, are not compliant with the sections 6.5.8 of the C standard
(C99) which states that: "If the expression P points to an element of
an array object and the expression Q points to the last element of the
same array object, the pointer expression Q+1 compares greater than P".
When executing clock_gettime(), either in the vDSO or via a system call,
we need to ensure that the read of the counter register occurs within
the seqlock reader critical section. This ensures that updates to the
clocksource parameters (e.g. the multiplier) are consistent with the
counter value and therefore avoids the situation where time appears to
go backwards across multiple reads.
Extend the vDSO logic so that the seqlock critical section covers the
read of the counter register as well as accesses to the data page. Since
reads of the counter system registers are not ordered by memory barrier
instructions, introduce dependency ordering from the counter read to a
subsequent memory access so that the seqlock memory barriers apply to
the counter access in both the vDSO and the system call paths.
The file offset argument to the arm64 sys_mmap() implementation is
scaled from bytes to pages by shifting right by PAGE_SHIFT.
Unfortunately, the offset is passed in as a signed 'off_t' type and
therefore large offsets (i.e. with the top bit set) are incorrectly
sign-extended by the shift. This has been observed to cause false mmap()
failures when mapping GPU doorbells on an arm64 server part.
Change the type of the file offset argument to sys_mmap() from 'off_t'
to 'unsigned long' so that the shifting scales the value as expected.
The ACEPC T8 and T11 Cherry Trail Z8350 mini PCs use an AXP288 and as PCs,
rather then portables, they does not have a battery. Still for some
reason the AXP288 not only thinks there is a battery, it actually
thinks it is discharging while the PC is running, slowly going to
0% full, causing userspace to shutdown the system due to the battery
being critically low after a while.
This commit adds the ACEPC T8 and T11 to the axp288 fuel-gauge driver
blacklist, so that we stop reporting bogus battery readings on this device.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1690852 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message reporting any errors
and returning *pirq*
Addresses-Coverity-ID: 1443940 ("Improper use of negative value") Fixes: 843735b788a4 ("power: axp288_charger: axp288 charger driver") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with warnings like:
arch/arm/mach-exynos/firmware.c:201:2-8: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 193,
but without a corresponding object release within this function.
Cc: stable@vger.kernel.org Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct commands (DCMDs) are an optional feature of eMMC 5.1's command
queue engine (CQE). The Arasan eMMC 5.1 controller uses the CQHCI,
which exposes a control register bit to enable the feature.
The current implementation sets this bit unconditionally.
This patch allows to suppress the feature activation,
by specifying the property disable-cqe-dcmd.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of CODEC input widget to which microphone is connected through
the "Headphone" jack is "IN12" not "IN1". This fixes microphone support
on Odroid XU3.
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:
The driver shows this message only for the first spurious interrupt
by using WARN_ONCE(). Changing this to WARN() shows, that this is
happening quite frequently (up to once a second).
Since the eMMC 5.1 specification, where CQE and CQHCI are specified,
does not mention that spurious TCN interrupts for DCMDs can be simply
ignored, we must assume that using this feature is not working reliably.
The current implementation uses DCMD for REQ_OP_FLUSH only, and
I could not see any performance/power impact when disabling
this optional feature for RK3399.
Therefore this patch disables DCMDs for RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: stable@vger.kernel.org
[the corresponding code changes are queued for 5.2 so doing that as well] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes IO domain voltage setting that is related to
audio_gpio3d4a_ms (bit 1) of GRF_IO_VSEL.
This is because RockPro64 schematics P.16 says that regulator
supplies 3.0V power to APIO5_VDD. So audio_gpio3d4a_ms bit should
be clear (means 3.0V). Power domain map is saying different thing
(supplies 1.8V) but I believe P.16 is actual connectings.
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Cc: stable@vger.kernel.org Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a function falls through to the next function due to a compiler
bug, objtool prints some obscure warnings. For example:
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x95: return with modified stack frame
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x0: stack state mismatch: cfa1=7+32 cfa2=7+8
Instead it should be printing:
drivers/regulator/core.o: warning: objtool: regulator_supply_is_couple() falls through to next function regulator_count_voltages()
This used to work, but was broken by the following commit:
13810435b9a7 ("objtool: Support GCC 8's cold subfunctions")
The padding nops at the end of a function aren't actually part of the
function, as defined by the symbol table. So the 'func' variable in
validate_branch() is getting cleared to NULL when a padding nop is
encountered, breaking the fallthrough detection.
If the current instruction doesn't have a function associated with it,
just consider it to be part of the previously detected function by not
overwriting the previous value of 'func'.
On x86_64, all returns to usermode go through
prepare_exit_to_usermode(), with the sole exception of do_nmi().
This even includes machine checks -- this was added several years
ago to support MCE recovery. Update the documentation.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/999fa9e126ba6a48e9d214d2f18dbde5c62ac55c.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The double fault ESPFIX path doesn't return to user mode at all --
it returns back to the kernel by simulating a #GP fault.
prepare_exit_to_usermode() will run on the way out of
general_protection before running user code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/ac97612445c0a44ee10374f6ea79c222fe22a5c4.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During my rwsem testing, it was found that after a down_read(), the
reader count may occasionally become 0 or even negative. Consequently,
a writer may steal the lock at that time and execute with the reader
in parallel thus breaking the mutual exclusion guarantee of the write
lock. In other words, both readers and writer can become rwsem owners
simultaneously.
The current reader wakeup code does it in one pass to clear waiter->task
and put them into wake_q before fully incrementing the reader count.
Once waiter->task is cleared, the corresponding reader may see it,
finish the critical section and do unlock to decrement the count before
the count is incremented. This is not a problem if there is only one
reader to wake up as the count has been pre-incremented by 1. It is
a problem if there are more than one readers to be woken up and writer
can steal the lock.
The wakeup was actually done in 2 passes before the following v4.9 commit:
70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once")
To fix this problem, the wakeup is now done in two passes
again. In the first pass, we collect the readers and count them.
The reader count is then fully incremented. In the second pass, the
waiter->task is then cleared and they are put into wake_q to be woken
up later.
Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Will Deacon <will.deacon@arm.com> Cc: huang ying <huang.ying.caritas@gmail.com> Fixes: 70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once") Link: http://lkml.kernel.org/r/20190428212557.13482-2-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For a single device mount using a zoned block device, the zone
information for the device is stored in the sbi->devs single entry
array and sbi->s_ndevs is set to 1. This differs from a single device
mount using a regular block device which does not allocate sbi->devs
and sets sbi->s_ndevs to 0.
However, sbi->s_devs == 0 condition is used throughout the code to
differentiate a single device mount from a multi-device mount where
sbi->s_ndevs is always larger than 1. This results in problems with
single zoned block device volumes as these are treated as multi-device
mounts but do not have the start_blk and end_blk information set. One
of the problem observed is skipping of zone discard issuing resulting in
write commands being issued to full zones or unaligned to a zone write
pointer.
Fix this problem by simply treating the cases sbi->s_ndevs == 0 (single
regular block device mount) and sbi->s_ndevs == 1 (single zoned block
device mount) in the same manner. This is done by introducing the
helper function f2fs_is_multi_device() and using this helper in place
of direct tests of sbi->s_ndevs value, improving code readability.
Fixes: 7bb3a371d199 ("f2fs: Fix zoned block device support") Cc: <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we hot-remove a device, usually the host sends us a PCI_EJECT message,
and a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
When we execute the quick hot-add/hot-remove test, the host may not send
us the PCI_EJECT message if the guest has not fully finished the
initialization by sending the PCI_RESOURCES_ASSIGNED* message to the
host, so it's potentially unsafe to only depend on the
pci_destroy_slot() in hv_eject_device_work() because the code path
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
is not called in this case. Note: in this case, the host still sends the
guest a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
In the quick hot-add/hot-remove test, we can have such a race before
the code path
adds the new device into the hbus->children list, we may have already
received the PCI_EJECT message, and since the tasklet handler
hv_pci_onchannelcallback()
may fail to find the "hpdev" by calling
get_pcichild_wslot(hbus, dev_message->wslot.slot)
hv_pci_eject_device() is not called; Later, by continuing execution
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
creates the slot and the PCI_BUS_RELATIONS message with
bus_rel->device_count == 0 removes the device from hbus->children, and
we end up being unable to remove the slot in
hv_pci_remove()
-> hv_pci_remove_slots()
Remove the slot in pci_devices_present_work() when the device
is removed to address this race.
pci_devices_present_work() and hv_eject_device_work() run in the
singled-threaded hbus->wq, so there is not a double-remove issue for the
slot.
We cannot offload hv_pci_eject_device() from hv_pci_onchannelcallback()
to the workqueue, because we need the hv_pci_onchannelcallback()
synchronously call hv_pci_eject_device() to poll the channel
ringbuffer to work around the "hangs in hv_compose_msi_msg()" issue
fixed in commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in
hv_compose_msi_msg()")
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: rewritten commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unload the pci-hyperv host controller driver, the host does not
send us a PCI_EJECT message.
In this case we also need to make sure the sysfs PCI slot directory is
removed, otherwise a command on a slot file eg:
"cat /sys/bus/pci/slots/2/address"
will trigger a
"BUG: unable to handle kernel paging request"
and, if we unload/reload the driver several times we would end up with
stale slot entries in PCI slot directories in /sys/bus/pci/slots/
root@localhost:~# ls -rtl /sys/bus/pci/slots/
total 0
drwxr-xr-x 2 root root 0 Feb 7 10:49 2
drwxr-xr-x 2 root root 0 Feb 7 10:49 2-1
drwxr-xr-x 2 root root 0 Feb 7 10:51 2-2
Add the missing code to remove the PCI slot and fix the current
behaviour.
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: reformatted the log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'desc' should be freed before leaving from err handing path.
Fixes: 1ce9e6055fa0 ("virtio_ring: introduce packed ring support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set RI in the default kernel's MSR so that the architected way of
detecting unrecoverable machine check interrupts has a chance to work.
This is inline with the MSR setup of the rest of booke powerpc
architectures configured here.
Without restoring the IAMR after idle, execution prevention on POWER9
with Radix MMU is overwritten and the kernel can freely execute
userspace without faulting.
This is necessary when returning from any stop state that modifies
user state, as well as hypervisor state.
To test how this fails without this patch, load the lkdtm driver and
do the following:
When the memset code was added to pgd_alloc(), it failed to consider
that kmem_cache_alloc() can return NULL. It's uncommon, but not
impossible under heavy memory contention. Example oops:
The "param.count" value is a u64 thatcomes from the user. The code
later in the function assumes that param.count is at least one and if
it's not then it leads to an Oops when we dereference the ZERO_SIZE_PTR.
Also the addition can have an integer overflow which would lead us to
allocate a smaller "pages" array than required. I can't immediately
tell what the possible run times implications are, but it's safest to
prevent the overflow.
Link: http://lkml.kernel.org/r/20181218082129.GE32567@kadam Fixes: 6db7199407ca ("drivers/virt: introduce Freescale hypervisor management driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Timur Tabi <timur@freescale.com> Cc: Mihai Caraman <mihai.caraman@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch to make bas_gigaset use usb_fill_int_urb() - instead of
filling that urb "by hand" - missed the subtle ordering of the previous
code.
See, before the switch urb->dev was set to a member somewhere deep in a
complicated structure and then supplied to usb_rcvisocpipe() and
usb_sndisocpipe(). After that switch urb->dev wasn't set to anything
specific before being supplied to those two macros. This triggers a
nasty oops:
No-one noticed because this Oops is apparently only triggered by setting
up an ISDN data connection on a live ISDN line on a gigaset base (ie,
the PBX that the gigaset driver support). Very few people do that
running present day kernels.
Anyhow, a little code reorganization makes this problem go away, while
avoiding the subtle ordering that was used in the past. So let's do
that.
Fixes: 78c696c19578 ("isdn: gigaset: use usb_fill_int_urb()") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue(tfile) is detached through __tun_detach(), we move the
last enabled tfile to the position where detached one sit but don't
NULL out last position. We expect to synchronize the datapath through
tun->numqueues. Unfortunately, this won't work since we're lacking
sufficient mechanism to order or synchronize the access to
tun->numqueues.
To fix this, NULL out the last position during detaching and check
RCU protected tfile against NULL instead of checking tun->numqueues in
datapath.
Cc: YueHaibing <yuehaibing@huawei.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: weiyongjun (A) <weiyongjun1@huawei.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Fixes: c8d68e6be1c3b ("tuntap: multiqueue support") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need check if tun->numqueues is zero (e.g for the persist device)
before trying to use it for modular arithmetic.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 96f84061620c6("tun: add eBPF based queue selection method") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VRF netdev mtu isn't typically set and have an mtu of 65536. When the
link of a tunnel is set, the tunnel mtu is changed from 1480 to the link
mtu minus tunnel header. In the case of VRF netdev is the link, then the
tunnel mtu becomes 65516. So, fix it by not setting the tunnel mtu in
this case.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With NET_ADMIN enabled in container, a normal user could be mapped to
root and is able to change the real device's rx filter via ioctl on
vlan, which would affect the other ptp process on host. Fix it by
disabling SIOCSHWTSTAMP in container.
Fixes: a6111d3c93d0 ("vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 517d7c79bdb398 ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bdb398
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bdb398 ("tipc: fix hanging poll() for stream sockets") Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit 68741a8adab9
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.
Fix the above falling back to the generic/old code when the address family
is not AF_INET{4,6}, but leave the SCTP code path untouched, as it has
specific constraints.
Fixes: 68741a8adab9 ("selinux: Fix ltp test connect-syscall failure") Reported-by: Tom Deseyn <tdeseyn@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe af_packet, register_pernet_subsys
fails and does a cleanup, ops->list is set to LIST_POISON1,
but the module init is considered to success, then while rmmod it,
BUG() is triggered in __list_del_entry_valid which is called from
unregister_pernet_subsys. This patch fix error handing path in
packet_init to avoid possilbe issue if some error occur.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing the number of buffers in the RX ring while the interface
is running, the following Oops is encountered due to the new number
of buffers being taken into account immediately while their allocation
is done when opening the device only.
The old MIPS implementation of dma_cache_sync() didn't use the dev argument,
but commit c9eb6172c328 ("dma-mapping: turn dma_cache_sync into a
dma_map_ops method") changed that, so we now need to set dev.parent.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
