The media bus bit width of MEDIA_BUS_FMT_RGB101010_1X30 is 30.
So, 'Bit31' and 'Bit30' cells for the 'MEDIA_BUS_FMT_RGB101010_1X30'
row should be spaces instead of '0's.
Fixes: 54f38fcae536 ("media: docs: move uAPI book to userspace-api/media") Signed-off-by: Liu Ying <victor.liu@nxp.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function i2c_new_dummy_device() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: e6089feca460 ("media: m88ds3103: Add support for ds3103b demod") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When sun6i_video_remote_subdev() returns NULL to subdev, no error return
code of sun6i_video_start_streaming() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Fixes: 5cc7522d8965 ("media: sun6i: Add support for Allwinner CSI V3s") Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful 'of_icc_get()' call, it must be
undone.
Use 'devm_of_icc_get()' instead of 'of_icc_get()' to avoid the leak.
Update the remove function accordingly and axe the now unneeded
'icc_put()' calls.
drm_helper_hpd_irq_event() checks the epoch counter to determine
connector status change. This was introduced in
commit 5186421cbfe2 ("drm: Introduce epoch counter to drm_connector").
Do the same for output_poll_execute() so it can detect other changes
beside connection status value changes.
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting.
Fixes: d2b4387f3bdf ("media: platform: Add Aspeed Video Engine driver") Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Eddie James <eajames@linux.ibm.com> Fixes: d3d04f6c330a ("clk: Add support for AST2600 SoC") Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When setting the source media bus code in the resizer,
we first check that the current media bus code in the
source is yuv encoded format. This is done by
retrieving the data from the formats list of the isp
entity. This cause a crash when the media bus code on the
source is YUYV8_1_5X8 which is not supported by the isp
entity. Instead we should test the sink format of the resizer
which is guaranteed to be supported by the isp entity.
Fixes: 251b6eebb6c49 ("media: staging: rkisp1: rsz: Add support to more YUV encoded mbus codes on src pad") Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Acked-by: Helen Koike <helen.koike@collabora.com> Tested-by: Sebastian Fricke <sebastian.fricke.linux@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The new AMD IOMMU DMA implementation concatenates sglist entries under
certain conditions, and because saa7146 accessed the length member
directly, it did not support this scenario.
This fixes IO_PAGE_FAULTs by using the sg_dma_len macro.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api") Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The new AMD IOMMU DMA implementation concatenates sglist entries under
certain conditions, and because saa7134 accessed the length member
directly, it did not support this scenario.
This fixes IO_PAGE_FAULTs and choppy DMA audio by using the
sg_dma_len macro.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api") Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the chroma_flags and alpha_flags are being zero'd with a bit-wise
mask and the following statement should be bit-wise or'ing in the new flag
bits but instead is making a direct assignment. Fix this by using the |=
operator rather than an assignment.
Addresses-Coverity: ("Unused value")
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rcu_nmi_enter(), there is an erroneous instrumentation_end() in the
second branch of the "if" statement. Oddly enough, "objtool check -f
vmlinux.o" fails to complain because it is unable to correctly cover
all cases. Instead, objtool visits the third branch first, which marks
following trace_rcu_dyntick() as visited. This commit therefore removes
the spurious instrumentation_end().
Fixes: 04b25a495bd6 ("rcu: Mark rcu_nmi_enter() call to rcu_cleanup_after_idle() noinstr")
Reported-by Neeraj Upadhyay <neeraju@codeaurora.org> Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The second loop of syslog_print_all() subtracts lengths that were
added in the first loop. With commit b031a684bfd0 ("printk: remove
logbuf_lock writer-protection of ringbuffer") it is possible that
records are (over)written during syslog_print_all(). This allows the
possibility of the second loop subtracting lengths that were never
added in the first loop.
This situation can result in syslog_print_all() filling the buffer
starting from a later record, even though there may have been room
to fit the earlier record(s) as well.
Fixes: b031a684bfd0 ("printk: remove logbuf_lock writer-protection of ringbuffer") Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20210303101528.29901-4-john.ogness@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported a handful of occurrences where an sd->nr_balance_failed can
grow to much higher values than one would expect.
A successful load_balance() resets it to 0; a failed one increments
it. Once it gets to sd->cache_nice_tries + 3, this *should* trigger an
active balance, which will either set it to sd->cache_nice_tries+1 or reset
it to 0. However, in case the to-be-active-balanced task is not allowed to
run on env->dst_cpu, then the increment is done without any further
modification.
This could then be repeated ad nauseam, and would explain the absurdly high
values reported by syzbot (86, 149). VincentG noted there is value in
letting sd->cache_nice_tries grow, so the shift itself should be
fixed. That means preventing:
"""
If the value of the right operand is negative or is greater than or equal
to the width of the promoted left operand, the behavior is undefined.
"""
Thus we need to cap the shift exponent to
BITS_PER_TYPE(typeof(lefthand)) - 1.
I had a look around for other similar cases via coccinelle:
@cst depends on expr@
position pos;
expression expr.E1;
constant cst;
@@
(
E1 >> cst@pos
|
E1 << cst@pos
)
@script:python depends on !cst@
pos << expr.pos;
exp << expr.E2;
@@
# Dirty hack to ignore constexpr
if exp.upper() != exp:
coccilib.report.print_report(pos[0], "Possible UB shift here")
The only other match in kernel/sched is rq_clock_thermal() which employs
sched_thermal_decay_shift, and that exponent is already capped to 10, so
that one is fine.
It is possible to call lpfc_issue_els_plogi() passing a did for which no
matching ndlp is found. A call is then made to lpfc_prep_els_iocb() with a
null pointer to a lpfc_nodelist structure resulting in a null pointer
dereference.
Fix by returning an error status if no valid ndlp is found. Fix up comments
regarding ndlp reference counting.
Link: https://lore.kernel.org/r/20210301171821.3427-10-jsmart2021@gmail.com Fixes: 4430f7fd09ec ("scsi: lpfc: Rework locations of ndlp reference taking") Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A recent patch renaming MIPI_DSI_MODE_EOT_PACKET to
MIPI_DSI_MODE_NO_EOT_PACKET brought to light the
misunderstanding in the current MCDE driver and all
its associated panel drivers that MIPI_DSI_MODE_EOT_PACKET
would mean "use EOT packet" when in fact it means the
reverse.
Fix it up by implementing the flag right in the MCDE
DSI driver and remove the flag from panels that actually
want the EOT packet.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Nicolas Boichat <drinkcat@chromium.org> Fixes: 5fc537bfd000 ("drm/mcde: Add new driver for ST-Ericsson MCDE") Fixes: 899f24ed8d3a ("drm/panel: Add driver for Novatek NT35510-based panels") Fixes: ac1d6d74884e ("drm/panel: Add driver for Samsung S6D16D0 panel") Fixes: 435e06c06cb2 ("drm/panel: s6e63m0: Add DSI transport") Fixes: 8152c2bfd780 ("drm/panel: Add driver for Sony ACX424AKP panel") Link: https://patchwork.freedesktop.org/patch/msgid/20210304004138.1785057-1-linus.walleij@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The hdcp_i2c_offsets[] array did not have an entry for
HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one
read overflow. I added an entry and copied the 0x0 value for the offset
from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c.
I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX
entries. This doesn't change the code, but it's just a belt and
suspenders approach to try future proof the code.
The drm_display_mode_to_videomode() does not populate DISPLAY_FLAGS_DE_LOW
or DISPLAY_FLAGS_PIXDATA_NEGEDGE flags in struct videomode. Therefore, no
matter what polarity the next bridge or display might require, these flags
are never set, and thus the LTDC GCR_DEPOL and GCR_PCPOL bits are never set
and the LTDC behaves as if both DISPLAY_FLAGS_PIXDATA_POSEDGE and
DISPLAY_FLAGS_DE_HIGH were always set.
The fix for this problem is taken almost verbatim from MXSFB driver. In
case there is a bridge attached to the LTDC, the bridge might have extra
polarity requirements, so extract bus_flags from the bridge and use them
for LTDC configuration. Otherwise, extract bus_flags from the connector,
which is the display.
Fixes: b759012c5fa7 ("drm/stm: Add STM32 LTDC driver") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org Tested-by: Yannick Fertre <yannick.fertre@foss.st.com> Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210127110756.125570-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
When run xrandr to change resolution on Beaglebone Black board, it will
print the error information:
root@beaglebone:~# xrandr -display :0 --output HDMI-1 --mode 720x400
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:32:tilcdc crtc] commit wait timed out
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:34:HDMI-A-1] commit wait timed out
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:31:plane-0] commit wait timed out
tilcdc 4830e000.lcdc: already pending page flip!
This is because there is operation sequence as below:
drm_atomic_connector_commit_dpms(mode is DRM_MODE_DPMS_OFF):
...
drm_atomic_helper_setup_commit <- init_completion(commit_A->flip_done)
drm_atomic_helper_commit_tail
tilcdc_crtc_atomic_disable
tilcdc_plane_atomic_update <- drm_crtc_send_vblank_event in tilcdc_crtc_irq
is skipped since tilcdc_crtc->enabled is 0
tilcdc_crtc_atomic_flush <- drm_crtc_send_vblank_event is skipped since
crtc->state->event is set to be NULL in
tilcdc_plane_atomic_update
drm_mode_setcrtc:
...
drm_atomic_helper_setup_commit <- init_completion(commit_B->flip_done)
drm_atomic_helper_wait_for_dependencies
drm_crtc_commit_wait <- wait for commit_A->flip_done completing
Just as shown above, the steps which could complete commit_A->flip_done
are all skipped and commit_A->flip_done will never be completed. This will
result a time-out ERROR when drm_crtc_commit_wait check the commit_A->flip_done.
So add drm_crtc_send_vblank_event in tilcdc_crtc_atomic_disable to
complete commit_A->flip_done.
Fixes: cb345decb4d2 ("drm/tilcdc: Use standard drm_atomic_helper_commit") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi> Tested-by: Jyri Sarha <jyri.sarha@iki.fi> Signed-off-by: Jyri Sarha <jyri.sarha@iki.fi> Link: https://patchwork.freedesktop.org/patch/msgid/20210209082415.382602-1-quanyang.wang@windriver.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The intent here was to return negative error codes but it actually
returns positive values. The problem is that type promotion with
ternary operations is quite complicated.
"ret" is an int. "copied" is a u32. And the snoop_file_read() function
returns long. What happens is that "ret" is cast to u32 and becomes
positive then it's cast to long and it's still positive.
Fix this by removing the ternary so that "ret" is type promoted directly
to long.
Prior to commit 4a8c31a1c6f5 ("xen/blkback: rework connect_ring() to avoid
inconsistent xenstore 'ring-page-order' set by malicious blkfront"), the
behaviour of xen-blkback when connecting to a frontend was:
- read 'ring-page-order'
- if not present then expect a single page ring specified by 'ring-ref'
- else expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
This was correct behaviour, but was broken by the afforementioned commit to
become:
- read 'ring-page-order'
- if not present then expect a single page ring (i.e. ring-page-order = 0)
- expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
- if that didn't work then see if there's a single page ring specified by
'ring-ref'
This incorrect behaviour works most of the time but fails when a frontend
that sets 'ring-page-order' is unloaded and replaced by one that does not
because, instead of reading 'ring-ref', xen-blkback will read the stale
'ring-ref0' left around by the previous frontend will try to map the wrong
grant reference.
This patch restores the original behaviour.
Fixes: 4a8c31a1c6f5 ("xen/blkback: rework connect_ring() to avoid inconsistent xenstore 'ring-page-order' set by malicious blkfront") Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com> Link: https://lore.kernel.org/r/20210202175659.18452-1-paul@xen.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Data received during half-duplex transmission must be filtered.
If the target device responds quickly, emptying the FIFO at the end of
the transmission can erase not only the echo characters but also part of
the response message.
By keeping the receive interrupt enabled even during transmission, it
allows you to filter each echo character and only in a number equal to
those transmitted.
The issue was generated by a target device that started responding
240us later having received a request in communication at 115200bps.
Sometimes, some messages received by the target were missing some of the
first bytes.
Fixes: 3a13884abea0 ("tty/serial: omap: empty the RX FIFO at the end of half-duplex TX") Signed-off-by: Dario Binacchi <dariobin@libero.it> Link: https://lore.kernel.org/r/20210418094705.27014-1-dariobin@libero.it Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are rs485 transceivers (e.g. MAX13487E/MAX13488E) which
automatically disable or enable the driver and receiver to keep the bus
in the correct state.
In these cases we don't need a GPIO for flow control.
int main(int argc, char *argv[])
{
int i;
int fd[10];
for (i = 0; i < 10; i++)
fd[i] = open("/dev/ttyprintk", O_WRONLY);
ioctl(fd[0], TIOCVHANGUP);
for (i = 0; i < 10; i++)
close(fd[i]);
close(open("/dev/ttyprintk", O_WRONLY));
return 0;
}
----------
When TTY hangup happens, port->count needs to be reset via
"struct tty_operations"->hangup callback.
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.
Hibernation fails on a system in fips mode because md5 is used for the e820
integrity check and is not available. Use crc32 instead.
The check is intended to detect whether the E820 memory map provided
by the firmware after cold boot unexpectedly differs from the one that
was in use when the hibernation image was created. In this case, the
hibernation image cannot be restored, as it may cover memory regions
that are no longer available to the OS.
A non-cryptographic checksum such as CRC-32 is sufficient to detect such
inadvertent deviations.
Fixes: 62a03defeabd ("PM / hibernate: Verify the consistent of e820 memory map by md5 digest") Reviewed-by: Eric Biggers <ebiggers@google.com> Tested-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Chris von Recklinghausen <crecklin@redhat.com>
[ rjw: Subject edit ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987efc8 ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e9873: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When handling op->addr, it is using the buffer "tmpbuf" which has been
freed. This will trigger a use-after-free KASAN warning. Let's use
temporary variables to store op->addr.val and op->cmd.opcode to fix
this issue.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210416004652.2975446-5-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:
Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.
And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.
Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "open_info" variable is added to the &vmbus_connection.chn_msg_list,
but the error handling frees "open_info" without removing it from the
list. This will result in a use after free. First remove it from the
list, and then free it.
Fixes: 6f3d791f3006 ("Drivers: hv: vmbus: Fix rescind handling issues") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrea Parri <parri.andrea@gmail.com> Link: https://lore.kernel.org/r/YHV3XLCot6xBS44r@mwanda Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The si7021 was incorrectly placed at 0x20 on i2c bus 7. It is at 0x40.
Fixes: 9c44db7096e0 ("ARM: dts: aspeed: rainier: Add i2c devices") Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
pmc_plt_clk* clocks are used for ethernet controllers, so need to stay
turned on. This adds the affected board family to critclk_systems DMI
table, so the clocks are marked as CLK_CRITICAL and not turned off.
This replaces the previously listed boards with a match for the whole
device family CBxx63. CBxx63 matches only baytrail devices.
There are new affected boards that would otherwise need to be listed.
There are unaffected boards in the family, but having the clocks
turned on is not an issue.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Link: https://lore.kernel.org/r/20210412133006.397679-1-linux-kernel-dev@beckhoff.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In TPM 1.2 an authorization was a 20 byte number. The spec actually
recommended you to hash variable length passwords and use the sha1
hash as the authorization. Because the spec doesn't require this
hashing, the current authorization for trusted keys is a 40 digit hex
number. For TPM 2.0 the spec allows the passing in of variable length
passwords and passphrases directly, so we should allow that in trusted
keys for ease of use. Update the 'blobauth' parameter to take this
into account, so we can now use plain text passwords for the keys.
so before
keyctl add trusted kmk "new 32 blobauth=f572d396fae9206628714fb2ce00f72e94f2258fkeyhandle=81000001" @u
after we will accept both the old hex sha1 form as well as a new
directly supplied password:
keyctl add trusted kmk "new 32 blobauth=hello keyhandle=81000001" @u
Since a sha1 hex code must be exactly 40 bytes long and a direct
password must be 20 or less, we use the length as the discriminator
for which form is input.
Note this is both and enhancement and a potential bug fix. The TPM
2.0 spec requires us to strip leading zeros, meaning empyty
authorization is a zero length HMAC whereas we're currently passing in
20 bytes of zeros. A lot of TPMs simply accept this as OK, but the
Microsoft TPM emulator rejects it with TPM_RC_BAD_AUTH, so this patch
makes the Microsoft TPM emulator work with trusted keys.
Fixes: 0fe5480303a1 ("keys, trusted: seal/unseal with TPM 2.0 chips") Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The platform_get_resource_byname() can return NULL which would be
immediately dereferenced by resource_size(). Instead dereference it
after validating the resource.
When the superuser flushes the entire cache, the mmap_read_lock() is not
taken, but mmap_read_unlock() is called. Add the missing
mmap_read_lock() call.
Fixes: cd2567b6850b1648 ("m68k: call find_vma with the mmap_sem held in sys_cacheflush()") Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Link: https://lore.kernel.org/r/20210407200032.764445-1-Liam.Howlett@Oracle.com Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rxchannel id is updated by the driver using the
port no value, but this does not ensure that the value
is correct. So now rx channel value is obtained from
etoc channel map value.
We can't use kfree() to free device managed resources so the kfree(dev)
is against the rules.
It's easier to write this code if we open code the device_register() as
a device_initialize() and device_add(). That way if dev_set_name() set
name fails we can call put_device() and it will clean up correctly.
When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'
Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.
Fixes: 916f743da354 ("firmware: qcom: scm: Move the scm driver to drivers/firmware") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: He Ying <heying24@huawei.com> Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Support for termiox was added by commit 1d65b4a088de ("tty: Add
termiox") in 2008 but no driver support ever followed and it was
recently ripped out by commit e0efb3168d34 ("tty: Remove dead termiox
code").
Fix the return value for the unsupported termiox ioctls, which have
always returned -EINVAL, by explicitly returning -ENOTTY rather than
removing them completely and falling back to the default unrecognised-
ioctl handling.
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e667 ("USB: allow users to run setserial with cdc-acm") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db0a ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Li <wangli74@huawei.com> Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.
The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.
So let's switch to hardware dummy cycles transfer to fix this issue.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 -- 4 % complete
(Press Ctrl+C)
[ 169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.603480] spi-nor spi0.0: Erase operation failed.
[ 173.608368] spi-nor spi0.0: Attempted to modify a protected sector.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When current CPU load is not L0 then loading armada-37xx-cpufreq.ko driver
fails with following error:
# modprobe armada-37xx-cpufreq
[ 502.702097] Unsupported CPU frequency 250 MHz
This issue was partially fixed by commit 8db82563451f ("cpufreq:
armada-37xx: fix frequency calculation for opp"), but only for calculating
CPU frequency for opp.
Fix this also for determination of base CPU frequency.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for
opp") changed calculation of frequency passed to the dev_pm_opp_add()
function call. But the code for dev_pm_opp_remove() function call was not
updated, so the driver cleanup phase does not work when registration fails.
This fixes the issue by using the same frequency in both calls.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for opp") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CPU frequency is at 250 MHz and set_rate() is called with 500 MHz (L1)
quickly followed by a call with 1 GHz (L0), the CPU does not necessarily
stay in L1 for at least 20ms as is required by Marvell errata.
This situation happens frequently with the ondemand cpufreq governor and
can be also reproduced with userspace governor. In most cases it causes CPU
to crash.
This change fixes the above issue and ensures that the CPU always stays in
L1 for at least 20ms when switching from any state to L0.
Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 61c40f35f5cd ("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that the workaround introduced by commit 61c40f35f5cd
("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to
1.2GHz") when base CPU frequency is 1.2 GHz is also required when base
CPU frequency is 1 GHz. Otherwise switching CPU frequency directly from
L2 (250 MHz) to L0 (1 GHz) causes a crash.
When base CPU frequency is just 800 MHz no crashed were observed during
switch from L2 to L0.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original CPU voltage value for load L1 is too low for Armada 37xx SoC
when base CPU frequency is 1000 or 1200 MHz. It leads to instabilities
where CPU gets stuck soon after dynamic voltage scaling from load L1 to L0.
Update the CPU voltage value for load L1 accordingly when base frequency is
1000 or 1200 MHz. The minimal L1 value for base CPU frequency 1000 MHz is
updated from the original 1.05V to 1.108V and for 1200 MHz is updated to
1.155V. This minimal L1 value is used only in the case when it is lower
than value for L0.
This change fixes CPU instability issues on 1 GHz and 1.2 GHz variants of
Espressobin and 1 GHz Turris Mox.
Marvell previously for 1 GHz variant of Espressobin provided a patch [1]
suitable only for their Marvell Linux kernel 4.4 fork which workarounded
this issue. Patch forced CPU voltage value to 1.108V in all loads. But
such change does not fix CPU instability issues on 1.2 GHz variants of
Armada 3720 SoC.
During testing we come to the conclusion that using 1.108V as minimal
value for L1 load makes 1 GHz variants of Espressobin and Turris Mox boards
stable. And similarly 1.155V for 1.2 GHz variant of Espressobin.
These two values 1.108V and 1.155V are documented in Armada 3700 Hardware
Specifications as typical initial CPU voltage values.
Discussion about this issue is also at the Armbian forum [2].
This method was supposed to be needed by the armada-37xx-cpufreq driver,
but was never actually called due to wrong assumptions in the cpufreq
driver. After this was fixed in the cpufreq driver, this method is not
needed anymore.
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CPU frequency determining software [1] we have discovered that
after this driver does one CPU frequency change, the base frequency of
the CPU is set to the frequency of TBG-A-P clock, instead of the TBG
that is parent to the CPU.
This can be reproduced on EspressoBIN and Turris MOX:
cd /sys/devices/system/cpu/cpufreq/policy0
echo powersave >scaling_governor
echo performance >scaling_governor
Running the mhz tool before this driver is loaded reports 1000 MHz, and
after loading the driver and executing commands above the tool reports
800 MHz.
The change of TBG clock selector is supposed to happen in function
armada37xx_cpufreq_dvfs_setup. Before the function returns, it does
this:
parent = clk_get_parent(clk);
clk_set_parent(clk, parent);
The armada-37xx-periph clock driver has the .set_parent method
implemented correctly for this, so if the method was actually called,
this would work. But since the introduction of the common clock
framework in commit b2476490ef11 ("clk: introduce the common clock..."),
the clk_set_parent function checks whether the parent is actually
changing, and if the requested new parent is same as the old parent
(which is obviously the case for the code above), the .set_parent method
is not called at all.
This patch fixes this issue by filling the correct TBG clock selector
directly in the armada37xx_cpufreq_dvfs_setup during the filling of
other registers at the same address. But the determination of CPU TBG
index cannot be done via the common clock framework, therefore we need
to access the North Bridge Peripheral Clock registers directly in this
driver.
[1] https://github.com/wtarreau/mhz
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
As far as I can tell, the only difference between 'struct cppc_attr'
and 'struct kobj_attribute' aside from the type of the attr parameter
is the type of the count parameter in the ->store() member (ssize_t vs.
size_t), which does not actually matter because all of these nodes are
read-only.
Eliminate 'struct cppc_attr' in favor of 'struct kobj_attribute' to fix
the violation.
When CONFIG_ARM_QCOM_SPM_CPUIDLE is y and CONFIG_MMU is not set,
compiling errors are encountered as follows:
drivers/cpuidle/cpuidle-qcom-spm.o: In function `spm_dev_probe':
cpuidle-qcom-spm.c:(.text+0x140): undefined reference to `cpu_resume_arm'
cpuidle-qcom-spm.c:(.text+0x148): undefined reference to `cpu_resume_arm'
Note that cpu_resume_arm is defined when MMU is set. So, add dependency
on MMU in ARM_QCOM_SPM_CPUIDLE configuration.
Fixes: a871be6b8eee ("cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: He Ying <heying24@huawei.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210406123328.92904-1-heying24@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that no validation of how much data the firmware loader read in
for a given segment truncated segment files would best case result in a
hash verification failure, without any indication of what went wrong.
Improve this by validating that the firmware loader did return the
amount of data requested.
The code validates that segments of p_memsz bytes of a segment will fit
in the provided memory region, but does not validate that p_filesz bytes
will, which means that an incorrectly crafted ELF header might write
beyond the provided memory region.
Fixes: 051fb70fd4ea ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Reviewed-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20210107233119.717173-1-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a5c ("spi: Introduce device-managed SPI controller allocation") Signed-off-by: William A. Kennington III <wak@google.com> Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: ca7b72b5a5f2 ("clocksource: Add driver for the Ingenic JZ47xx OST") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210308123031.2285083-1-weiyongjun1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid spurious timer interrupts when KTIME_MAX is used, we need to
configure set_state_oneshot_stopped(). Although implementing this is
optional, it still affects things like power management for the extra
timer interrupt.
For more information, please see commit 8fff52fd5093 ("clockevents:
Introduce CLOCK_EVT_STATE_ONESHOT_STOPPED state") and commit cf8c5009ee37
("clockevents/drivers/arm_arch_timer: Implement
->set_state_oneshot_stopped()").
Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210304072135.52712-4-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the timer is configured in posted mode, we need to check the write-
posted status register (TWPS) before writing to the register.
We now check TWPS after the write starting with commit 52762fbd1c47
("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource
support").
For example, in the TRM for am571x the following is documented in chapter
"22.2.4.13.1.1 Write Posting Synchronization Mode":
"For each register, a status bit is provided in the timer write-posted
status (TWPS) register. In this mode, it is mandatory that software check
this status bit before any write access. If a write is attempted to a
register with a previous access pending, the previous access is discarded
without notice."
The regression happened when I updated the code to use standard read/write
accessors for the driver instead of using __omap_dm_timer_load_start().
We have__omap_dm_timer_load_start() check the TWPS status correctly using
__omap_dm_timer_write().
Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210304072135.52712-2-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Make init_bios_attributes() ACPI object parsing more robust:
1. Always check that the type of the return ACPI object is package, rather
then only checking this for instance_id == 0
2. Check that the package has the minimum amount of elements which will
be consumed by the populate_foo_data() for the attr_type
Note/TODO: The populate_foo_data() functions should also be made more
robust. The should check the type of each of the elements matches the
type which they expect and in case of populate_enum_data()
obj->package.count should be passed to it as an argument and it should
re-check this itself since it consume a variable number of elements.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321121607.35717-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the greybus implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: e68453ed28c5 ("greybus: uart-gb: now builds, more framework added") Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210407102334.32361-7-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Fix the fwserial implementation by dropping its custom interpretation of
the unused xmit_fifo_size field, which was overflowed with the driver
FIFO size. Also leave the type and flags fields unset as these cannot be
changed.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
closing_wait, but let's report back the default value actually used (30
seconds).
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the fwserial implementation which was returning -EPERM also for a
privileged user when trying to change certain unsupported parameters,
and instead return success consistently.
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of riv->ieee80211->LinkDetectInfo.SlotNum
that is a u16 type. There is a potential infinite loop if SlotNum
is larger than the u8 loop counter. Fix this by making the loop
counter the same type as SlotNum.
Addresses-Coverity: ("Infinite loop") Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210407150308.496623-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `ni_routes_test` module is not currently selectable using the
Kconfig files, but can be built by specifying `CONFIG_COMEDI_TESTS=m` on
the "make" command line. It currently fails to compile due to an extra
parameter added to the `ni_assign_device_routes` function by
commit e3b7ce73c578 ("staging: comedi: ni_routes: Allow alternate board
name for routes"). Fix it by supplying the value `NULL` for the added
`alt_board_name` parameter (which specifies that there is no alternate
board name).
Fixes: e3b7ce73c578 ("staging: comedi: ni_routes: Allow alternate board name for routes") Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20210407140142.447250-2-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c24 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Because a dependency on HAS_IOMEM and OF was added for the ADI AXI ADC
driver, this makes the AD9467 driver have some build/dependency issues
when OF is disabled (typically on ACPI archs like x86).
This is because the selection of the AD9467 enforces the ADI_AXI_ADC symbol
which is blocked by the OF (and potentially HAS_IOMEM) being disabled.
To fix this, we make the AD9467 driver depend on the ADI_AXI_ADC symbol.
The AD9467 driver cannot operate on it's own. It requires the ADI AXI ADC
driver to stream data (or some similar IIO interface).
So, the fix here is to make the AD9467 symbol depend on the ADI_AXI_ADC
symbol. At some point this could become it's own subgroup of high-speed
ADCs.
Fixes: be24c65e9fa24 ("iio: adc: adi-axi-adc: add proper Kconfig dependencies") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210324182746.9337-1-aardelean@deviqon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some SC7180 firmwares don't implement the QCOM_SCM_INFO_IS_CALL_AVAIL
API, so we can't probe the calling convention. We detect the legacy
calling convention on these firmwares, because the availability call
always fails and legacy is the fallback. This leads to problems where
the rmtfs driver fails to probe, because it tries to assign memory with
a bad calling convention, which then leads to modem failing to load and
all networking, even wifi, to fail. Ouch!
Let's force the calling convention to be what it always is on this SoC,
i.e. arm64. Of course, the calling convention is not the same thing as
implementing the QCOM_SCM_INFO_IS_CALL_AVAIL API. The absence of the "is
this call available" API from the firmware means that any call to
__qcom_scm_is_call_available() fails. This is OK for now though because
none of the calls that are checked for existence are implemented on
firmware running on sc7180. If such a call needs to be checked for
existence in the future, we presume that firmware will implement this
API and then things will "just work".
Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 9a434cee773a ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-4-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We shouldn't need to hold this spinlock here around the entire SCM call
into the firmware and back. Instead, we should be able to query the
firmware, potentially in parallel with other CPUs making the same
convention detection firmware call, and then grab the lock to update the
calling convention detected. The convention doesn't change at runtime so
calling into firmware more than once is possibly wasteful but simpler.
Besides, this is the slow path, not the fast path where we've already
detected the convention used.
More importantly, this allows us to add more logic here to workaround
the case where the firmware call to check for availability isn't
implemented in the firmware at all. In that case we can check the
firmware node compatible string and force a calling convention.
Note that we remove the 'has_queried' logic that is repeated twice. That
could lead to the calling convention being printed multiple times to the
kernel logs if the bool is true but __query_convention() is running on
multiple CPUs. We also shorten the time where the lock is held, but we
keep the lock held around the printk because it doesn't seem hugely
important to drop it for that.
Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 9a434cee773a ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-3-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make __qcom_scm_is_call_available() return bool instead of int. The
function has "is" in the name, so it should return a bool to indicate
the truth of the call being available. Unfortunately, it can return a
number < 0 which also looks "true", but not all callers expect that and
thus they think a call is available when really the check to see if the
call is available failed to figure it out.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 0f206514749b ("scsi: firmware: qcom_scm: Add support for programming inline crypto keys") Fixes: 0434a4061471 ("firmware: qcom: scm: add support to restore secure config to qcm_scm-32") Fixes: b0a1614fb1f5 ("firmware: qcom: scm: add OCMEM lock/unlock interface") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-2-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't clear the timer 1 configuration bits when clearing the interrupt flag
and counter overflow. As Michael reported, "This results in no timer
interrupts being delivered after the first. Initialization then hangs
in calibrate_delay as the jiffies counter is not updated."
On mvme16x, enable the timer after requesting the irq, consistent with
mvme147.
When stream config is failed, master runtime will release all
slave runtime in the slave_rt_list, but slave runtime is not
added to the list at this time. This patch frees slave runtime
in the config error path to fix the memory leak.
Fixes: 89e590535f32 ("soundwire: Add support for SoundWire stream management") Signed-off-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Keyon Jie <yang.jie@intel.com> Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20210331004610.12242-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
projects / thirdparty / kernel / stable.git / log
