In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> CC: <stable@vger.kernel.org> CC: <linux-omap@vger.kernel.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This patch uses iio_trigger_get to increment the reference
count of trigger device, to avoid incorrect assignment.
Can result in a null pointer dereference during removal if the
trigger has been changed before removal.
This patch refers to a similar situation encountered through the
following discussion:
http://www.spinics.net/lists/linux-iio/msg13669.html
Depending on conversion mode used, the ADC clock (ADCK) needs
to be below a maximum frequency. According to Vybrid's data
sheet this is 20MHz for the low power conversion mode.
The ADC clock is depending on input clock, which is the bus
clock by default. Vybrid SoC are typically clocked at at 400MHz
or 500MHz, which leads to 66MHz or 83MHz bus clock respectively.
Hence, a divider of 8 is required to stay below the specified
maximum clock of 20MHz.
Due to the different bus clock speeds, the resulting sampling
frequency is not static. Hence use the ADC clock and calculate
the actual available sampling frequency dynamically.
This fixes bogous values observed on some 500MHz clocked Vybrid
SoC. The resulting value usually showed Bit 9 being stuck at 1,
or 0, which lead to a value of +/-512.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Fugang Duan <B38611@freescale.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Currently driver reports device bandwidth list as available
sampling frequency. But sampling frequency is actually twice
the device bandwidth. This patch fixes this issue.
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order
to avoid attaching a TTY to the JTAG port as this board is based on the
CALAO Systems reference design and needs the same fix up.
Add USB VID/PID for Xircom PGMFHUB USB/serial component. (The hub and SCSI
bridge on that hardware are recognized out of the box by existing drivers.)
Tested VID/PID using new_id and loopback connection and was met with
success, but that's all the testing done.
Use readb() and memcpy_fromio() accessors instead.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
2f800fbd777b ("writeback: fix dirtied pages accounting on redirty")
introduced account_page_redirty() which reverts stat updates for a
redirtied page, making BDI_DIRTIED no longer monotonically increasing.
bdi_update_write_bandwidth() uses the delta in BDI_DIRTIED as the
basis for bandwidth calculation. While unlikely, since the above
patch, the newer value may be lower than the recorded past value and
underflow the bandwidth calculation leading to a wild result.
Fix it by subtracing min of the old and new values when calculating
delta. AFAIK, there hasn't been any report of it happening but the
resulting erratic behavior would be non-critical and temporary, so
it's possible that the issue is happening without being reported. The
risk of the fix is very low, so tagged for -stable.
global_update_bandwidth() uses static variable update_time as the
timestamp for the last update but forgets to initialize it to
INITIALIZE_JIFFIES.
This means that global_dirty_limit will be 5 mins into the future on
32bit and some large amount jiffies into the past on 64bit. This
isn't critical as the only effect is that global_dirty_limit won't be
updated for the first 5 mins after booting on 32bit machines,
especially given the auxiliary nature of global_dirty_limit's role -
protecting against global dirty threshold's sudden dips; however, it
does lead to unintended suboptimal behavior. Fix it.
All CPUs leaving the first-online CPU are hotplugged out on suspend and
and cpufreq core stops managing them.
On resume, we need to call cpufreq_update_policy() for this CPU's policy
to make sure its frequency is in sync with cpufreq's cached value, as it
might have got updated by hardware during suspend/resume.
The policies are always added to the top of the policy-list. So, in
normal circumstances, CPU 0's policy will be the last one in the list.
And so the code checks for the last policy.
But there are cases where it will fail. Consider quad-core system, with
policy-per core. If CPU0 is hotplugged out and added back again, the
last policy will be on CPU1 :(
To fix this in a proper way, always look for the policy of the first
online CPU. That way we will be sure that we are calling
cpufreq_update_policy() for the only CPU that wasn't hotplugged out.
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+ Fixes: 2f0aea936360 ("cpufreq: suspend governors on system suspend/hibernate") Reported-by: Saravana Kannan <skannan@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Saravana Kannan <skannan@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
When non-realtime tasks get priority-inheritance boosted to a realtime
scheduling class, RLIMIT_RTTIME starts to apply to them. However, the
counter used for checking this (the same one used for SCHED_RR
timeslices) was not getting reset. This meant that tasks running with a
non-realtime scheduling class which are repeatedly boosted to a realtime
one, but never block while they are running realtime, eventually hit the
timeout without ever running for a time over the limit. This patch
resets the realtime timeslice counter when un-PI-boosting from an RT to
a non-RT scheduling class.
I have some test code with two threads and a shared PTHREAD_PRIO_INHERIT
mutex which induces priority boosting and spins while boosted that gets
killed by a SIGXCPU on non-fixed kernels but doesn't with this patch
applied. It happens much faster with a CONFIG_PREEMPT_RT kernel, and
does happen eventually with PREEMPT_VOLUNTARY kernels.
Commit 3c605096d315 ("mm/page_alloc: restrict max order of merging on
isolated pageblock") changed the logic of unset_migratetype_isolate to
check the buddy allocator and explicitly call __free_pages to merge.
The page that is being freed in this path never had prep_new_page called
so set_page_refcounted is called explicitly but there is no call to
kernel_map_pages. With the default kernel_map_pages this is mostly
harmless but if kernel_map_pages does any manipulation of the page
tables (unmapping or setting pages to read only) this may trigger a
fault:
The cause is the "memset(pgdat, 0, sizeof(*pgdat))" at the end of
try_offline_node, which will reset all the content of pgdat to 0, as the
pgdat is accessed lock-free, so that the users still using the pgdat
will panic, such as the vmstat_update routine.
process A: offline node XX:
vmstat_updat()
refresh_cpu_vm_stats()
for_each_populated_zone()
find online node XX
cond_resched()
offline cpu and memory, then try_offline_node()
node_set_offline(nid), and memset(pgdat, 0, sizeof(*pgdat))
zone = next_zone(zone)
pg_data_t *pgdat = zone->zone_pgdat; // here pgdat is NULL now
next_online_pgdat(pgdat)
next_online_node(pgdat->node_id); // NULL pointer access
So the solution here is postponing the reset of obsolete pgdat from
try_offline_node() to hotadd_new_pgdat(), and just resetting
pgdat->nr_zones and pgdat->classzone_idx to be 0 rather than the memset
0 to avoid breaking pointer information in pgdat.
I have constantly stumbled upon "kernel BUG at mm/rmap.c:399!" after
upgrading to 3.19 and had no luck with 4.0-rc1 neither.
So, after looking into new logic introduced by commit 7a3ef208e662 ("mm:
prevent endless growth of anon_vma hierarchy"), I found chances are that
unlink_anon_vmas() is called without incrementing dst->anon_vma->degree
in anon_vma_clone() due to allocation failure. If dst->anon_vma is not
NULL in error path, its degree will be incorrectly decremented in
unlink_anon_vmas() and eventually underflow when exiting as a result of
another call to unlink_anon_vmas(). That's how "kernel BUG at
mm/rmap.c:399!" is triggered for me.
This patch fixes the underflow by dropping dst->anon_vma when allocation
fails. It's safe to do so regardless of original value of dst->anon_vma
because dst->anon_vma doesn't have valid meaning if anon_vma_clone()
fails. Besides, callers don't care dst->anon_vma in such case neither.
Also suggested by Michal Hocko, we can clean up vma_adjust() a bit as
anon_vma_clone() now does the work.
[akpm@linux-foundation.org: tweak comment] Fixes: 7a3ef208e662 ("mm: prevent endless growth of anon_vma hierarchy") Signed-off-by: Leon Yu <chianglungyu@gmail.com> Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e662 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com> Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com> Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu> Cc: Michal Hocko <mhocko@suse.cz> Cc: stable@vger.kernel.org # to match back-porting of 7a3ef208e662 Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Constantly forking task causes unlimited grow of anon_vma chain. Each
next child allocates new level of anon_vmas and links vma to all
previous levels because pages might be inherited from any level.
This patch adds heuristic which decides to reuse existing anon_vma
instead of forking new one. It adds counter anon_vma->degree which
counts linked vmas and directly descending anon_vmas and reuses anon_vma
if counter is lower than two. As a result each anon_vma has either vma
or at least two descending anon_vmas. In such trees half of nodes are
leafs with alive vmas, thus count of anon_vmas is no more than two times
bigger than count of vmas.
This heuristic reuses anon_vmas as few as possible because each reuse
adds false aliasing among vmas and rmap walker ought to scan more ptes
when it searches where page is might be mapped.
Link: http://lkml.kernel.org/r/20120816024610.GA5350@evergreen.ssec.wisc.edu Fixes: 5beb49305251 ("mm: change anon_vma linking to fix multi-process server scalability issue")
[akpm@linux-foundation.org: fix typo, per Rik] Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Reported-by: Daniel Forrest <dan.forrest@ssec.wisc.edu> Tested-by: Michal Hocko <mhocko@suse.cz> Tested-by: Jerome Marchand <jmarchan@redhat.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: <stable@vger.kernel.org> [2.6.34+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Implement arch_irq_work_has_interrupt() for powerpc
Commit 9b01f5bf3 introduced a dependency on "IRQ work self-IPIs" for
full dynamic ticks to be enabled, by expecting architectures to
implement a suitable arch_irq_work_has_interrupt() routine.
Several arches have implemented this routine, including x86 (3010279f)
and arm (09f6edd4), but powerpc was omitted.
This patch implements this routine for powerpc.
The symptom, at boot (on powerpc systems) with "nohz_full=<CPU list>"
is displayed:
NO_HZ: Can't run full dynticks because arch doesn't support irq work self-IPIs
after this patch:
NO_HZ: Full dynticks CPUs: <CPU list>.
Tested against 3.19.
powerpc implements "IRQ work self-IPIs" by setting the decrementer to 1 in
arch_irq_work_raise(), which causes a decrementer exception on the next
timebase tick. We then handle the work in __timer_interrupt().
CC: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Paul A. Clarke <pc@us.ibm.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[mpe: Flesh out change log, fix ws & include guards, remove include of processor.h] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Space allocated for paca is based off nr_cpu_ids,
but pnv_alloc_idle_core_states() iterates paca with
cpu_nr_cores()*threads_per_core, which is using NR_CPUS.
This causes pnv_alloc_idle_core_states() to write over memory,
which is outside of paca array and may later lead to various panics.
Fixes: 7cba160ad789 (powernv/cpuidle: Redesign idle states management) Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
alloc_init_lock_stateowner can return an already freed entry if there is
a race to put openowners in the hashtable.
Noticed by inspection after Jeff Layton fixed the same bug for open
owners. Depending on client behavior, this one may be trickier to
trigger in practice.
Fixes: c58c6610ec24 "nfsd: Protect adding/removing lock owners using client_lock" Cc: <stable@vger.kernel.org> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Acked-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
alloc_init_open_stateowner can return an already freed entry if there is
a race to put openowners in the hashtable.
In commit 7ffb588086e9, we changed it so that we allocate and initialize
an openowner, and then check to see if a matching one got stuffed into
the hashtable in the meantime. If it did, then we free the one we just
allocated and take a reference on the one already there. There is a bug
here though. The code will then return the pointer to the one that was
allocated (and has now been freed).
This wasn't evident before as this race almost never occurred. The Linux
kernel client used to serialize requests for a single openowner. That
has changed now with v4.0 kernels, and this race can now easily occur.
Fixes: 7ffb588086e9 Cc: <stable@vger.kernel.org> # v3.17+ Cc: Trond Myklebust <trond.myklebust@primarydata.com> Reported-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
To be able to add memory pages which were added via memory hotplug to
a pv domain, the pages must be "invalid" instead of "identity" in the
p2m list before they can be added.
Suggested-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Cc: <stable@vger.kernel.org> # 3.16+ Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159 Cc: <stable@vger.kernel.org> Signed-off-by: Shachar Raindel <raindel@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Some bios really like to joke and start the planes at an offset ...
hooray!
Align start and end to fix this.
v2: Fixup calculation of size, spotted by Chris Wilson.
v3: Fix serious fumble I've just spotted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86883 Cc: stable@vger.kernel.org Cc: Johannes W <jargon@molb.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reported-and-tested-by: Johannes W <jargon@molb.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: split WARN_ONs, rebase on v4.0-rc1] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see 85250ddff7a6 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7a1 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Tested-by: Darren Hart <dvhart@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Deepak S <deepak.s@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see 85250ddff7a6 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7a1 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
We need to wait for all fences, not just the exclusive one.
Signed-off-by: Christian König <christian.koenig@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Christian König <christian.koenig@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The legcy colorkey ioctls are only implemented for sprite planes, so
reject the ioctl for primary/cursor planes. If we want to support
colorkeying with these planes (assuming we have hw support of course)
we should just move ahead with the colorkey property conversion.
Testcase: kms_legacy_colorkey Cc: Tommi Rantala <tt.rantala@gmail.com> Cc: stable@vger.kernel.org
Reference: http://mid.gmane.org/CA+ydwtr+bCo7LJ44JFmUkVRx144UDFgOS+aJTfK6KHtvBDVuAw@mail.gmail.com Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
If the user supplies EDID through firmware or debugfs override, the
driver callbacks are bypassed and the connector ELD does not get
updated, and audio fails. Set ELD for firmware and debugfs EDIDs too.
There should be no harm in gratuitously doing this for non HDMI/DP
connectors, as it's still up to the driver to use the ELD, if any.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82349
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=80691 Reported-by: Emil <emilsvennesson@gmail.com> Reported-by: Rob Engle <grenoble@gmail.com> Tested-by: Jolan Luff <jolan@gormsby.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
we've switched to weak references, broke that assumption but forgot to
fix it up.
Since we still force-disable planes it's only possible to hit this
when racing multiple rmfb with fbdev restoring or similar evil things.
As long as userspace is nice it's impossible to hit the BUG_ON.
But the BUG_ON would most likely be hit from fbdev code, which usually
invovles the console_lock besides all modeset locks. So very likely
we'd never get the bug reports if this was hit in the wild, hence
better be safe than sorry and backport.
Spotted by Matt Roper while reviewing other patches.
[airlied: pull this back into 4.0 - the oops happens there]
Cc: stable@vger.kernel.org Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
As the sunxi usb clocks all contain a reset controller, it is not
possible to build the sunxi clock driver without RESET_CONTROLLER
enabled. Doing so results in an undefined symbol error:
drivers/built-in.o: In function `sunxi_gates_clk_setup':
linux/drivers/clk/sunxi/clk-sunxi.c:1071: undefined reference to
`reset_controller_register'
This is possible if building a minimal kernel without PHY_SUN4I_USB.
The dependency issue is made visible at compile time instead of
link time by the new A80 mmc clocks, which also use a reset control
itself.
This patch makes ARCH_SUNXI select ARCH_HAS_RESET_CONTROLLER and
RESET_CONTROLLER.
Fixes: 559482d1f950 ARM: sunxi: Split the various SoCs support in Kconfig Cc: <stable@vger.kernel.org> # 3.16+ Reported-by: Lourens Rozema <ik@lourensrozema.nl> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
A malicious signal handler / restorer can DOS the system by fudging the
user regs saved on stack, causing weird things such as sigreturn returning
to user mode PC but cpu state still being kernel mode....
Ensure that in sigreturn path status32 always has U bit; any other bogosity
(gargbage PC etc) will be taken care of by normal user mode exceptions mechanisms.
The regfile provided to SA_SIGINFO signal handler as ucontext was off by
one due to pt_regs gutter cleanups in 2013.
Before handling signal, user pt_regs are copied onto user_regs_struct and copied
back later. Both structs are binary compatible. This was all fine until
commit 2fa919045b72 (ARC: pt_regs update #2) which removed the empty stack slot
at top of pt_regs (corresponding to first pad) and made the corresponding
fixup in struct user_regs_struct (the pad in there was moved out of
@scratch - not removed altogether as it is part of ptrace ABI)
struct user_regs_struct {
+ long pad;
struct {
- long pad;
long bta, lp_start, lp_end,....
} scratch;
...
}
This meant that now user_regs_struct was off by 1 reg w.r.t pt_regs and
signal code needs to user_regs_struct.scratch to reflect it as pt_regs,
which is what this commit does.
This problem was hidden for 2 years, because both save/restore, despite
using wrong location, were using the same location. Only an interim
inspection (reproducer below) exposed the issue.
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration") Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301 Reported-by: Michael D Labriola <mlabriol@gdeb.com> Tested-by: Michael D Labriola <mlabriol@gdeb.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.18+ Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Commit fab4c256a58b ("PCI/AER: Add a TLP header print helper") introduced
the helper function __print_tlp_header(), but contrary to the intention,
the behaviour did change: Since we're taking the address of the parameter
t, the first 4 or 8 bytes printed will be the value of the pointer t
itself, and the remaining 12 or 8 bytes will be who-knows-what (something
from the stack).
We want to show the values of the four members of the struct
aer_header_log_regs; that can be done without ugly and error-prone casts.
On little-endian this should produce the same output as originally
intended, and since no-one has complained about getting garbage output so
far, I think big-endian should be ok too.
Some BIOS version of Fujitsu Lifebook T731 seems to set up the
headphone pin (0x21) without the assoc number 0x0f while it's set only
to the output on the docking port (0x1a). With the recent commit
[03ad6a8c93b6: ALSA: hda - Fix "PCM" name being used on one DAC when
there are two DACs], this resulted in the weird mixer element
mapping where the headphone on the laptop is assigned as a shared
volume with the speaker and the docking port is assigned as an
individual headphone.
This patch improves the situation by correcting the headphone pin
config to the more appropriate value.
Pin sense will active when power pin is wake up.
Power pin will not wake up immediately during resume state.
Add some delay to wait for power pin activated.
Some M-Audio devices require to receive bootup command just after
powering on, while codes in BeBoB driver doesn't work properly in
big-endian machine because the command should be aligned by
little-endian.
This commit fixes this bug. This fix should go to stable kernel.
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3237"
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
BugLink: http://bugs.launchpad.net/bugs/1381005
In canon mode, the read buffer head will advance over the buffer tail
if the input > 4095 bytes without receiving a line termination char.
Discard additional input until a line termination is received.
Before evaluating for overflow, the 'room' value is normalized for
I_PARMRK and 1 byte is reserved for line termination (even in !icanon
mode, in case the mode is switched). The following table shows the
transform:
actual buffer | 'room' value before overflow calc
space avail | !I_PARMRK | I_PARMRK
--------------------------------------------------
0 | -1 | -1
1 | 0 | 0
2 | 1 | 0
3 | 2 | 0
4+ | 3 | 1
When !icanon or when icanon and the read buffer contains newlines,
normalized 'room' values of -1 and 0 are clamped to 0, and
'overflow' is 0, so read_head is not adjusted and the input i/o loop
exits (setting no_room if called from flush_to_ldisc()). No input
is discarded since the reader does have input available to read
which ensures forward progress.
When icanon and the read buffer does not contain newlines and the
normalized 'room' value is 0, then overflow and room are reset to 1,
so that the i/o loop will process the next input char normally
(except for parity errors which are ignored). Thus, erasures, signalling
chars, 7-bit mode, etc. will continue to be handled properly.
If the input char processed was not a line termination char, then
the canon_head index will not have advanced, so the normalized 'room'
value will now be -1 and 'overflow' will be set, which indicates the
read_head can safely be reset, effectively erasing the last char
processed.
If the input char processed was a line termination, then the
canon_head index will have advanced, so 'overflow' is cleared to 0,
the read_head is not reset, and 'room' is cleared to 0, which exits
the i/o loop (because the reader now have input available to read
which ensures forward progress).
Note that it is possible for a line termination to be received, and
for the reader to copy the line to the user buffer before the
input i/o loop is ready to process the next input char. This is
why the i/o loop recomputes the room/overflow state with every
input char while handling overflow.
Finally, if the input data was processed without receiving
a line termination (so that overflow is still set), the pty
driver must receive a write wakeup. A pty writer may be waiting
to write more data in n_tty_write() but without unthrottling
here that wakeup will not arrive, and forward progress will halt.
(Normally, the pty writer is woken when the reader reads data out
of the buffer and more space become available).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backported from commit fb5ef9e7da39968fec6d6f37f20a23d23740c75e) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org> Cc: <stable@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: Don Fry <pcnet32@frontier.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Commit 746c9e9f92dd "of/base: Fix PowerPC address parsing hack" limited
the applicability of the workaround whereby a missing ranges is treated
as an empty ranges. This workaround was hiding a bug in the etsec2
device tree nodes, which have children with reg, but did not have
ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com> Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
We currently use the device tree update code in the kernel after resuming
from a suspend operation to re-sync the kernels view of the device tree with
that of the hypervisor. The code as it stands is not endian safe as it relies
on parsing buffers returned by RTAS calls that thusly contains data in big
endian format.
This patch annotates variables and structure members with __be types as well
as performing necessary byte swaps to cpu endian for data that needs to be
parsed.
The idle_task_exit() function may call switch_mm() with next ==
&init_mm. On arm64, init_mm.pgd cannot be used for user mappings, so
this patch simply sets the reserved TTBR0.
Cc: <stable@vger.kernel.org> Reported-by: Jon Medhurst (Tixy) <tixy@linaro.org> Tested-by: Jon Medhurst (Tixy) <tixy@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The register offset for REGEN2_CTRL in different for TPS659038 chip as when
compared with other Palmas family PMICs. In the case of TPS659038 the wrong
offset pointed to PLLEN_CTRL and was causing a hang. Correcting the same.
Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit id 2ba9f0d has changed CONFIG_KVM_BOOK3S_64_HV to tristate to allow
HV/PR bits to be built as modules. But the MCE code still depends on
CONFIG_KVM_BOOK3S_64_HV which is wrong. When user selects
CONFIG_KVM_BOOK3S_64_HV=m to build HV/PR bits as a separate module the
relevant MCE code gets excluded.
This patch fixes the MCE code to use CONFIG_KVM_BOOK3S_64_HANDLER. This
makes sure that the relevant MCE code is included when HV/PR bits
are built as a separate modules.
Fixes: 2ba9f0d88750 ("kvm: powerpc: book3s: Support building HV and PR KVM as module") Cc: stable@vger.kernel.org # v3.14+ Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Haswell moved the TOLM/TOHM registers to a different device and offset.
The sb_edac driver accounted for the change of device, but not for the
new offset. There was also a typo in the constant to fill in the low
26 bits (was 0x1ffffff, should be 0x3ffffff).
This resulted in a bogus value for the top of low memory:
Dirty page throttling should be sufficient for us in the general case
so there is no need to use __GFP_MEMALLOC - it would be needed only in
the swap-over-rbd case, which we currently don't support. (It would
probably take approximately the commit that is being reverted to add
that support, but we would also need the "swap" option to distinguish
from the general case and make sure swap ceph_client-s aren't shared
with anything else.) See ceph-devel threads [1] and [2] for the
details of why enabling pfmemalloc reserves for all cases is a bad
thing.
On top of potential system lockups related to drained emergency
reserves, this turned out to cause ceph lockups in case peers are on
the same host and communicating via loopback due to sk_filter()
dropping pfmemalloc skbs on the receiving side because the receiving
loopback socket is not tagged with SOCK_MEMALLOC.
[1] "SOCK_MEMALLOC vs loopback"
http://www.spinics.net/lists/ceph-devel/msg22998.html
[2] "[PATCH] libceph: don't set memalloc flags in loopback case"
http://www.spinics.net/lists/ceph-devel/msg23392.html
Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert(). In this case a hfs_brec_update_parent() is
called to update the parent index node (if exists) and it is passed
hfs_find_data with a search_key containing a newly inserted key instead
of the key to be updated. This results in an inconsistent index node.
The bug reproduces on my machine after an extents overflow record for
the catalog file (CNID=4) is inserted into the extents overflow B-tree.
Because of a low (reserved) value of CNID=4, it has to become the first
record in the first leaf node.
A change in hfs_brec_insert() makes hfs_brec_update_parent() work
correctly by preventing it from getting fd->record=-1 value from
__hfs_brec_find().
Along the way, I removed duplicate code with unification of the if
condition. The resulting code is equivalent to the original code
because node is never 0.
Also hfs_brec_update_parent() will now return an error after getting a
negative fd->record value. However, the return value of
hfs_brec_update_parent() is not checked anywhere in the file and I'm
leaving it unchanged by this patch. brec.c lacks error checking after
some other calls too, but this issue is of less importance than the one
being fixed by this patch.
Signed-off-by: Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Anton Altaparmakov <aia21@cam.ac.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
The "dm snapshot: suspend origin when doing exception handover" commit
fixed a exception store handover bug associated with pending exceptions
to the "snapshot-origin" target.
However, a similar problem exists in snapshot merging. When snapshot
merging is in progress, we use the target "snapshot-merge" instead of
"snapshot-origin". Consequently, during exception store handover, we
must find the snapshot-merge target and suspend its associated
mapped_device.
To avoid lockdep warnings, the target must be suspended and resumed
without holding _origins_lock.
Introduce a dm_hold() function that grabs a reference on a
mapped_device, but unlike dm_get(), it doesn't crash if the device has
the DMF_FREEING flag set, it returns an error in this case.
In snapshot_resume() we grab the reference to the origin device using
dm_hold() while holding _origins_lock (_origins_lock guarantees that the
device won't disappear). Then we release _origins_lock, suspend the
device and grab _origins_lock again.
NOTE to stable@ people:
When backporting to kernels 3.18 and older, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
In the function snapshot_resume we perform exception store handover. If
there is another active snapshot target, the exception store is moved
from this target to the target that is being resumed.
The problem is that if there is some pending exception, it will point to
an incorrect exception store after that handover, causing a crash due to
dm-snap-persistent.c:get_exception()'s BUG_ON.
This bug can be triggered by repeatedly changing snapshot permissions
with "lvchange -p r" and "lvchange -p rw" while there are writes on the
associated origin device.
To fix this bug, we must suspend the origin device when doing the
exception store handover to make sure that there are no pending
exceptions:
- introduce _origin_hash that keeps track of dm_origin structures.
- introduce functions __lookup_dm_origin, __insert_dm_origin and
__remove_dm_origin that manipulate the origin hash.
- modify snapshot_resume so that it calls dm_internal_suspend_fast() and
dm_internal_resume_fast() on the origin device.
NOTE to stable@ people:
When backporting to kernels 3.12-3.18, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
When backporting to kernels older than 3.12, you need to pick functions
dm_internal_suspend and dm_internal_resume from the commit fd2ed4d252701d3bbed4cd3e3d267ad469bb832a.
It was always intended that a read to an unprovisioned block will return
zeroes regardless of whether the pool is in read-only or read-write
mode. thin_bio_map() was inconsistent with its handling of such reads
when the pool is in read-only mode, it now properly zero-fills the bios
it returns in response to unprovisioned block reads.
Eliminate thin_bio_map()'s special read-only mode handling of -ENODATA
and just allow the IO to be deferred to the worker which will result in
pool->process_bio() handling the IO (which already properly zero-fills
reads to unprovisioned blocks).
Reported-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Since it's possible for the discard and write same queue limits to
change while the upper level command is being sliced and diced, fix up
both of them (a) to reject IO if the special command is unsupported at
the start of the function and (b) read the limits once and let the
commands error out on their own if the status happens to change.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The commit 9cade1a46c77 (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com> Fixes: 9cade1a46c77 (dma: dw: split driver to library part and platform code) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Which is caused by an irq_work generating new irq_work and therefore
not allowing forward progress.
This happens because processing the perf irq_work triggers another
perf event (tracepoint stuff) which in turn generates an irq_work ad
infinitum.
Avoid this by raising the recursion counter in the irq_work -- which
effectively disables all software events (including tracepoints) from
actually triggering again.
Reported-by: Vince Weaver <vincent.weaver@maine.edu> Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20150219170311.GH21418@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
As stated in kernel/cpu_pm.c, "Platform is responsible for ensuring
that cpu_pm_enter is not called twice on the same CPU before
cpu_pm_exit is called.". In the current code in case of failure when
calling mvebu_v7_cpu_suspend, the function cpu_pm_exit() is never
called whereas cpu_pm_enter() was called just before.
This patch moves the cpu_pm_exit() in order to balance the
cpu_pm_enter() calls.
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.18+] Cc: Alan Fisher <acf@unixcube.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added. Cc: <stable@vger.kernel.org> # v3.16+ Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Cc: stable <stable@vger.kernel.org> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Li Jun <b47624@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
A new uas compatible controller has shown up in some people's devices from
the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X
quirk to work properly with uas, so add it to the uas quirks table.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Cc: stable@vger.kernel.org [3.16+] Fixes: 73de86a38962b ("cfg80211/mac80211: move interface counting for combination check to mac80211") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[rewrite commit message, dig out the commit it fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Some APs experience problems when working with
U-APSD. Decreasing the probability of that
happening by using legacy mode for all ACs but VO
isn't enough.
Cisco 4410N originally forced us to enable VO by
default only because it treated non-VO ACs as
legacy.
However some APs (notably Netgear R7000) silently
reclassify packets to different ACs. Since u-APSD
ACs require trigger frames for frame retrieval
clients would never see some frames (e.g. ARP
responses) or would fetch them accidentally after
a long time.
It makes little sense to enable u-APSD queues by
default because it needs userspace applications to
be aware of it to actually take advantage of the
possible additional powersavings. Implicitly
depending on driver autotrigger frame support
doesn't make much sense.
Cc: stable@vger.kernel.org Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The Fimware 8.1 has a bug in which the extra buttons are only sent when the
ExtBit is 1. This should be fixed in a future FW update which should have
a bump of the minor version.
Cc: stable@vger.kernel.org Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle
button of the trackstick (attached to the touchpad serio device, of course)
seems to get lost.
Actually, the touchpads reports 3 extra buttons, which falls in the switch
below to the '2' case. Let's handle the case of odd numbers also, so that
the middle button finds its way back.
Cc: stable@vger.kernel.org Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Post-2013 Lenovo laptops provide correct min/max dimensions, which are
different with the ones currently quirked. According to
https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids
are assigned in the post-2013 touchpads:
Add a min/max range for board ids to the min/max coordinates quirk. This
makes it possible to restrict quirks to specific models based upon their
board id. The define ANY_BOARD_ID (0) serves as a wild card.
Cc: stable@vger.kernel.org Signed-off-by: Daniel Martin <daniel.martin@secunet.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The firmware of the X240 (LEN0035, 2013/12) exposes the same values
x [1232..5710], y [1156..4696]
as the quirk applies.
Cc: stable@vger.kernel.org Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: stable@vger.kernel.org Signed-off-by: Daniel Martin <consume.noise@gmail.com>
re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1 Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
projects / thirdparty / kernel / stable.git / log
