张鹏 [Fri, 16 Oct 2020 10:42:15 +0000 (12:42 +0200)]
ath79: add support for Qxwlan E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
张鹏 [Wed, 14 Oct 2020 07:47:35 +0000 (15:47 +0800)]
ath79: add support for Qxwlan E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Fri, 16 Oct 2020 19:42:11 +0000 (21:42 +0200)]
mac80211: fix memory leak on filtered powersave frames
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 8 Oct 2020 11:44:33 +0000 (13:44 +0200)]
mediatek: rewrite flow offload code
The code is now much cleaner and works better than the old code.
Preparation for submitting it upstream (though with a different API)
Also add back MT7621 support and fix flow table coherence issues on
MT7622
Daniel Golle [Fri, 16 Oct 2020 13:27:34 +0000 (14:27 +0100)]
config: clean up SELinux options
In order to make it easier for users to build with SELinux, have a
single option in 'Global build settings' to enable all necessary
kernel features, userland packages and build-system hooks.
Also add better descriptions and help messages while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 16 Oct 2020 00:51:13 +0000 (01:51 +0100)]
fstools: update to git HEAD
8e0f29a mount: remove support for legacy overlayfs before v2.3 0f8a443 mount: fix log format string and indentation 46a56d3 overlay: use precompiler macros for reoccuring path names f25ab8a mount: apply SELinux labels before overlayfs mount
Total ipk size change (ipq40xx): +120b
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 10 Oct 2020 22:04:13 +0000 (23:04 +0100)]
hostapd: ubus: add handler for wps_status and guard WPS calls
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Peng Zhang [Wed, 14 Oct 2020 07:47:35 +0000 (15:47 +0800)]
ath79: add support for Qxwlan E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[cut out of bigger patch, alter use of DEVICE_VARIANT, merge case
in 01_leds, use lower case for v4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this removes
the "devicename" from LED labels in rtl838x, as it's useless and
only creates complexity.
Since the target is fresh and so far only system LEDs were added,
this does not add a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Thu, 15 Oct 2020 08:17:45 +0000 (10:17 +0200)]
build: always build package/kernel/linux
build: always build package/kernel/linux
If no in-tree module packages are selected, the build system does not process
package/kernel/linux. This package is required for building the virtual
'kernel' package, which is specified as a dependency for all kernel packages.
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Birger Koblitz [Sat, 3 Oct 2020 09:20:48 +0000 (11:20 +0200)]
rtl838x: Add support for RTL839x internal PHY
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.
CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100/1000Mbps Ethernet
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input only
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
Power Supply: DC 5V/2A
PCB Dimension: 40 x 40 x 1.2mm
Installation:
Burn the image file to an SD Card with dd or any image burning tool
Boot ZeroPi from the SD Card
The following features are working and tested:
Ethernet port 10/100/1000M Ethernet
Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)
Andre Heider [Tue, 8 Oct 2019 19:15:44 +0000 (21:15 +0200)]
kernel: add a kmod package for the SoC S/PDIF codec
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Andre Heider [Tue, 8 Oct 2019 18:06:57 +0000 (20:06 +0200)]
kernel: fix name of CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM
CONFIG_SND_SOC_DMAENGINE_PCM was removed and replaced with
CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM seven years ago, see:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=28c4468b00a1e55e08cc20117de968f7c6275441
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b7ae6f31d8243ec684af16bc5c763eccdfabaec0
Andre Heider [Sat, 12 Sep 2020 07:32:41 +0000 (09:32 +0200)]
mvebu: Add bootscript for espressobin to support mainline firmware
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Tony Ambardar [Fri, 25 Sep 2020 03:52:37 +0000 (20:52 -0700)]
scripts/qemustart: update malta to use MIPS64 R2 cpu
Explicitly set the QEMU cpu type and support the MIPS R2 ISA, for both
64-bit and 32-bit targets. The later previously supported MIPS R2 by
implicit default.
This is needed after commit 93608697f3 ("malta: update MIPS64 ISA to R2"),
otherwise booting malta images with scripts/qemustart will hang.
Tony Ambardar [Fri, 14 Aug 2020 05:11:22 +0000 (22:11 -0700)]
malta: update MIPS64 ISA to R2
Usage of current R1 ISA is inconsistent with the MIPS32 subtarget, little
used and has limited utility for testing.
Many distros target a minimum R2 ISA. Debian MIPS 32-bit/64-bit ports all
use MIPS R2 ISA since Stretch, for example. Fedora's MIPS arch also targets
the R2 ISA for 32-bit/64-bit.
Widely used MIPS64 platforms like Octeon are based on the MIPS R2 ISA or
later, and benefit from having a compatible test platform in OpenWRT.
While Linux does support MIPS64 R1 targets, its usefulness for development
and testing is limited. As an example, the modern Linux eBPF JIT requires
a MIPS R2 ISA or later.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[Refresh config and fix README] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If you compile first libaudit library and then trace-cmd package,
compilations fails with:
Package trace-cmd is missing dependencies for the following libraries:
libaudit.so.1
If you enable libaudit for trace-cmd, it will show system name calls while using command profile.
Try to be slim as much as possible - libaudit .ipk has 42,4 kB.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Marek Behún [Sat, 26 Sep 2020 21:42:52 +0000 (21:42 +0000)]
perf: fix building with musl when NLS is enabled
This package fails with a strange error when building with musl when NLS
is enabled. The configuration thinks that libelf is not present, even
though DEPENDS contains +libelf, because when NLS is enabled, libelf.so
depends on libintl, and the correct LDFLAGS are missing for
libintl-full. This then causes the configuration script to check for
glibc, but this fails because we are using musl.
bcm63xx: add a few DTSI files to share definitions
After the LED labels have been made more general by removing
the model names, we can move several definitions to DTSI files
to reduce the amount of duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 9 Oct 2020 22:16:53 +0000 (23:16 +0100)]
kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Robert Marko [Wed, 7 Oct 2020 15:12:56 +0000 (17:12 +0200)]
ipq40xx: 5.4: move AR40xx driver into files
There is no point in keeping the AR40xx driver as a patch as its
not pending merge or backport.
To allow for easier maintenance until DSA is ready move it into
files like EDMA is.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[combine with removal from patches-5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Sun, 5 Feb 2017 16:55:53 +0000 (17:55 +0100)]
rt2x00: mt7620: differentiate based on SoC's CHIP_VER
The vendor driver does things differently based on what it finds in the
SoC's CHIP_VER register, which should tell whether this is MT7620N or
MT7620A (PKG) and probably also the revision (VER) and most likely
also something about the silicon implementer (ECO).
Introduce codepaths just like the ones in the vendor driver to handle
the different chips properly.
Some of those paths are most likely dead code and left-overs from FPGA
versions or early prototypes of the chip. It'd thus be great if people
can post their kernel logs, at least the line telling the chip version
and eco, so we know what's actually out there in the wild -- all I
could find is
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
and
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
which would make things easier, as then we really just need to know
whether it's MT7620N or MT7620A and not care about FPGA or prototypes
with ver <= 1 and eco <= 2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Mon, 5 Oct 2020 23:54:43 +0000 (13:54 -1000)]
kernel: clean up XATTR config symbols
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sven Roederer [Sun, 27 Sep 2020 21:07:38 +0000 (23:07 +0200)]
build, imagebuilder: Do not require compilers
The buildroot and SDK both require the compilers (gcc, g++) to be
installed on the host system, however the ImageBuilder uses precompiled
binaries.
This patch changes the prerequirements checks to skip the checking for
the compilers if running as ImageBuilder. A similar change has been
made for libncurses-dev in 4a1a58a3e2d2.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de> Acked-by: Paul Spooren <mail@aparcar.org>
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Fri, 18 Sep 2020 13:31:59 +0000 (22:31 +0900)]
ipq40xx: improve support for Edgecore ECW5211
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.
The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jo-Philipp Wich [Sun, 4 Oct 2020 21:04:51 +0000 (23:04 +0200)]
uhttpd: update to latest Git HEAD
14a3cb4 ubus: fix legacy empty reply format 0f38b03 client: fix spurious keepalive connection timeouts 88ba2fa client: really close connection on timeout c186212 ubus: support GET method with CORS requests
Joe Mullally [Sat, 12 Sep 2020 18:46:28 +0000 (19:46 +0100)]
ath79: add support for TP-Link TL-WPA8630P (EU) v2.1
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Andre Heider [Fri, 4 Sep 2020 07:30:49 +0000 (09:30 +0200)]
omap: update uboot to v2020.04
Fixes the build error:
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
00a84c5 linux-firmware: Update AMD SEV firmware 71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main 07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200 1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201 28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560 db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260 eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310 ec88f05 mediatek: update MT7915 firmware to 20200819 a9993f8 brcm: Fix a stale symlink for RPi3 model b+ f48fec4 qcom: Add updated a5xx and a6xx microcode d5f9eea wl18xx: update firmware file 8.9.0.0.83 7a237c6 linux-firmware: mt7615: update firmware to 20200814 version 74bd44f amdgpu: add navi12 firmware from 20.30 b9f69cd amdgpu: update navi10 firmware for 20.30
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Tue, 25 Aug 2020 13:26:05 +0000 (15:26 +0200)]
layerscape: add layerscape's SATA driver package
This patch intruduce SATA support for layerscape devices.
Target specific package with ahci_qoriq driver was added
to local modules.mk.
Kmod package was added to default packages for devices with
SATA interface.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.
Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
projects / thirdparty / openwrt.git / log
