This avoids an issue that occurs when we're attempting to preempt multiple
channels simultaneously. HW seems to ignore preempt requests while it's
still processing a previous one, which, well, makes sense.
Fixes random "fifo: SCHED_ERROR 0d []" + GPCCS page faults during parallel
piglit runs on (at least) GM107.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTM was changed a while back to allow for pipelining of buffer moves, and
part of this was the removal of waiting for a BO to idle before calling
move(), placing the responsibility on the driver to do this if required.
That's all well and good, except, we make use of move_notify() to handle
mapping/unmapping from the GPU VMM as move() isn't called on all paths.
This commit adds a wait before unmapping from a VMM in move_notify(), to
prevent GPU page faults where a buffer is still being accessed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Look for firmware files using the legacy ("nouveau/nvxx_fucxxxx") path
if they cannot be found in the new, "official" path. User setups were
broken by the switch, which is bad.
There are only 4 firmware files we may want to look up that way, so
hardcode them into the lookup function. All new firmware files should
use the standard "nvidia/<chip>/gr/" path.
Fixes: 8539b37acef7 ("drm/nouveau/gr: use NVIDIA-provided external firmwares") Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUI idle interrupts should be enabled only after we
have enabled coarse grain clock gating (CGCG). This
prevents GFX engine generating idle interrupt even
though CGCG is not completely enabled.
Most of the time this goes un-noticed, but on some
Stoney ASICs this results in GFX engine hang after
system resumes from suspend. The issue is not
particular to Stoney though and could have occured
on any ASIC. The patch fixes this issue.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Sunil Uttarwar <Sunil.Uttarwar1@amd.com> Signed-off-by: Arindam Nath <arindam.nath@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HP Pavilion dv6 has a non-working acpi_video0 backlight interface
and an intel_backlight interface which works fine. Add a force_native
quirk for it so that the non-working acpi_video0 interface does not get
registered.
Note that there are quite a few HP Pavilion dv6 variants, some
woth ATI and some with NVIDIA hybrid gfx, both seem to need this
quirk to have working backlight control. There are also some versions
with only Intel integrated gfx, these may not need this quirk, but it
should not hurt there.
The Dell XPS 17 L702X has a non-working acpi_video0 backlight interface
and an intel_backlight interface which works fine. Add a force_native
quirk for it so that the non-working acpi_video0 interface does not get
registered.
Note that there also is an issue with the brightnesskeys on this laptop,
they do not generate key-press events in anyway. That is not solved by
this patch.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1123661 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0557344e2149 ("staging: comedi: ni_mio_common: fix local var for
32-bit read") changed the type of local variable `d` from `unsigned
short` to `unsigned int` to fix a bug introduced in
commit 9c340ac934db ("staging: comedi: ni_stc.h: add read/write
callbacks to struct ni_private") when reading AI data for NI PCI-6110
and PCI-6111 cards. Unfortunately, other parts of the function rely on
the variable being `unsigned short` when an offset value in local
variable `signbits` is added to `d` before writing the value to the
`data` array:
d += signbits;
data[n] = d;
The `signbits` variable will be non-zero in bipolar mode, and is used to
convert the hardware's 2's complement, 16-bit numbers to Comedi's
straight binary sample format (with 0 representing the most negative
voltage). This breaks because `d` is now 32 bits wide instead of 16
bits wide, so after the addition of `signbits`, `data[n]` ends up being
set to values above 65536 for negative voltages. This affects all
supported "E series" cards except PCI-6143 (and PXI-6143). Fix it by
ANDing the value written to the `data[n]` with the mask 0xffff.
Fixes: 0557344e2149 ("staging: comedi: ni_mio_common: fix local var for 32-bit read") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For NI M Series cards, the Comedi `insn_read` handler for the AI
subdevice is broken due to ANDing the value read from the AI FIFO data
register with an incorrect mask. The incorrect mask clears all but the
most significant bit of the sample data. It should preserve all the
sample data bits. Correct it.
Fixes: 817144ae7fda ("staging: comedi: ni_mio_common: remove unnecessary use of 'board->adbits'") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"kernel BUG at drivers/hv/channel_mgmt.c:350!" is observed when hv_vmbus
module is unloaded. BUG_ON() was introduced in commit 85d9aa705184
("Drivers: hv: vmbus: add an API vmbus_hvsock_device_unregister()") as
vmbus_free_channels() codepath was apparently forgotten.
Fixes: 85d9aa705184 ("Drivers: hv: vmbus: add an API vmbus_hvsock_device_unregister()") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In docutils 0.13, the return type of get_column_widths method of the
Table directive has changed [1], which breaks our flat-table directive
and leads to a TypeError when trying to build the docs [2].
This patch adds support for the new return type, while keeping support
for older docutils versions too.
In the critical sysfs entry the thermal hwmon was returning wrong
temperature to the user-space. It was reporting the temperature of the
first trip point instead of the temperature of critical trip point.
For example:
/sys/class/hwmon/hwmon0/temp1_crit:50000
/sys/class/thermal/thermal_zone0/trip_point_0_temp:50000
/sys/class/thermal/thermal_zone0/trip_point_0_type:active
/sys/class/thermal/thermal_zone0/trip_point_3_temp:120000
/sys/class/thermal/thermal_zone0/trip_point_3_type:critical
Since commit e68b16abd91d ("thermal: add hwmon sysfs I/F") the driver
have been registering a sysfs entry if get_crit_temp() callback was
provided. However when accessed, it was calling get_trip_temp() instead
of the get_crit_temp().
bcm2835_pll_divider_off() is resetting the divider field in the A2W reg
to zero when disabling the clock.
Make sure we preserve this value by reading the previous a2w_reg value
first and ORing the result with A2W_PLL_CHANNEL_DISABLE.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the VDD_GPU regulator (a GPIO-enabled PWM regulator) to the Jetson
TX1 board. This addition allows the GPU to be used provided the
bootloader properly enabled the GPU node.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
[as pointed out by Thierry on IRC, nobody has reported a bug
in the field, but using a new bootloader with a .dtb that
has the incorrect data, it will crash on boot] Fixes: 336f79c7b6d7 ("arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO chardev is used for management tasks (allocating line and event
handles) and does neither support read() nor write() operations. Hence it
does not make much sense to allow seek operations.
Currently the chardev uses noop_llseek() for its seek implementation. This
function does not move the pointer and simply returns the current position
(always 0 for the GPIO chardev). noop_llseek() is primarily meant for
devices that can not support seek, but where there might be a user that
depends on the seek() operation succeeding. For newly added devices that
can not support seek operations it is recommended to use no_llseek(), which
will return an error. For more information see commit 6038f373a3dc
("llseek: automatically add .llseek fop").
Unfortunately this was overlooked when the GPIO chardev ABI was introduced.
But it is highly unlikely that since then userspace applications have
appeared that rely on being able to perform non-failing seek operations on
a GPIO chardev file descriptor. So it should be safe to change from
noop_llseel() to no_seek(). Also use nonseekable_open() in the chardev
open() callback to clear the FMODE_SEEK, FMODE_PREAD and FMODE_PWRITE flags
from the file. Neither of these should be set on a file that does not
support seek operations.
Fixes: 3c702e9987e2 ("gpio: add a userspace chardev ABI for GPIOs") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocksource delta to nanoseconds conversion is using signed math, but
the delta is unsigned. This makes the conversion space smaller than
necessary and in case of a multiplication overflow the conversion can
become negative. The conversion is done with scaled math:
Shifting a signed integer right obvioulsy preserves the sign, which has
interesting consequences:
- Time jumps backwards
- __iter_div_u64_rem() which is used in one of the calling code pathes
will take forever to piecewise calculate the seconds/nanoseconds part.
This has been reported by several people with different scenarios:
David observed that when stopping a VM with a debugger:
"It was essentially the stopped by debugger case. I forget exactly why,
but the guest was being explicitly stopped from outside, it wasn't just
scheduling lag. I think it was something in the vicinity of 10 minutes
stopped."
When lifting the stop the machine went dead.
The stopped by debugger case is not really interesting, but nevertheless it
would be a good thing not to die completely.
But this was also observed on a live system by Liav:
"When the OS is too overloaded, delta will get a high enough value for the
msb of the sum delta * tkr->mult + tkr->xtime_nsec to be set, and so
after the shift the nsec variable will gain a value similar to
0xffffffffff000000."
Unfortunately this has been reintroduced recently with commit 6bd58f09e1d8
("time: Add cycles to nanoseconds translation"). It had been fixed a year
ago already in commit 35a4933a8959 ("time: Avoid signed overflow in
timekeeping_get_ns()").
Though it's not surprising that the issue has been reintroduced because the
function itself and the whole call chain uses s64 for the result and the
propagation of it. The change in this recent commit is subtle:
s64 nsec;
- nsec = (d * m + n) >> s:
+ nsec = d * m + n;
+ nsec >>= s;
d being type of cycle_t adds another level of obfuscation.
This wouldn't have happened if the previous change to unsigned computation
would have made the 'nsec' variable u64 right away and a follow up patch
had cleaned up the whole call chain.
There have been patches submitted which basically did a revert of the above
patch leaving everything else unchanged as signed. Back to square one. This
spawned a admittedly pointless discussion about potential users which rely
on the unsigned behaviour until someone pointed out that it had been fixed
before. The changelogs of said patches added further confusion as they made
finally false claims about the consequences for eventual users which expect
signed results.
Despite delta being cycle_t, aka. u64, it's very well possible to hand in
a signed negative value and the signed computation will happily return the
correct result. But nobody actually sat down and analyzed the code which
was added as user after the propably unintended signed conversion.
Though in sensitive code like this it's better to analyze it proper and
make sure that nothing relies on this than hunting the subtle wreckage half
a year later. After analyzing all call chains it stands that no caller can
hand in a negative value (which actually would work due to the s64 cast)
and rely on the signed math to do the right thing.
Change the conversion function to unsigned math. The conversion of all call
chains is done in a follow up patch.
This solves the starvation issue, which was caused by the negative result,
but it does not solve the underlying problem. It merily procrastinates
it. When the timekeeper update is deferred long enough that the unsigned
multiplication overflows, then time going backwards is observable again.
It does neither solve the issue of clocksources with a small counter width
which will wrap around possibly several times and cause random time stamps
to be generated. But those are usually not found on systems used for
virtualization, so this is likely a non issue.
I took the liberty to claim authorship for this simply because
analyzing all callsites and writing the changelog took substantially
more time than just making the simple s/s64/u64/ change and ignore the
rest.
Fixes: 6bd58f09e1d8 ("time: Add cycles to nanoseconds translation") Reported-by: David Gibson <david@gibson.dropbear.id.au> Reported-by: Liav Rehana <liavr@mellanox.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Parit Bhargava <prarit@redhat.com> Cc: Laurent Vivier <lvivier@redhat.com> Cc: "Christopher S. Hall" <christopher.s.hall@intel.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Link: http://lkml.kernel.org/r/20161208204228.688545601@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regulator has never been properly enabled, it has been
dormant all the time. It's strange that MMC was working
at all, but it likely worked by the signals going through
the levelshifter and reaching the card anyways.
Fixes: 3615a34ea1a6 ("regulator: add STw481x VMMC driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b58f ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Dan O'Donovan <dan@emutex.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.") Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and SOC") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An earlier patch allowed enabling PT and LBR at the same
time on Goldmont. However it also allowed enabling BTS and LBR
at the same time, which is still not supported. Fix this by
bypassing the check only for PT.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: alexander.shishkin@intel.com Cc: kan.liang@intel.com Fixes: ccbebba4c6bf ("perf/x86/intel/pt: Bypass PT vs. LBR exclusivity if the core supports it") Link: http://lkml.kernel.org/r/20161209001417.4713-1-andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Reported-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global mutex of 'gdp_mutex' is used to serialize creating/querying
glue dir and its cleanup. Turns out it isn't a perfect way because
part(kobj_kset_leave()) of the actual cleanup action() is done inside
the release handler of the glue dir kobject. That means gdp_mutex has
to be held before releasing the last reference count of the glue dir
kobject.
This patch moves glue dir's cleanup after kobject_del() in device_del()
for avoiding the race.
Cc: Yijing Wang <wangyijing@huawei.com> Reported-by: Chandra Sekhar Lingutla <clingutla@codeaurora.org> Signed-off-by: Ming Lei <ming.lei@canonical.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kdump(kexec-tools) parses /proc/iomem to identify all the memory regions
on the system. Since the current kernel names "nomap" regions, like UEFI
runtime services code/data, as "System RAM," kexec-tools sets up elf core
header to include them in a crash dump file (/proc/vmcore).
Then crash dump kernel parses UEFI memory map again, re-marks those regions
as "nomap" and does not create a memory mapping for them unlike the other
areas of System RAM. In this case, copying /proc/vmcore through
copy_oldmem_page() on crash dump kernel will end up with a kernel abort,
as reported in [1].
This patch names all the "nomap" regions explicitly as "reserved" so that
we can exclude them from a crash dump file. acpi_os_ioremap() must also
be modified because those regions have WB attributes [2].
Apart from kdump, this change also matches x86's use of acpi (and
/proc/iomem).
xlog_recover_clear_agi_bucket didn't set the
type to XFS_BLFT_AGI_BUF, so we got a warning during log
replay (or an ASSERT on a debug build).
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
Fix this, as was done in f19b872b for 2 other locations
with the same problem.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xen_guest_init is using __alloc_percpu with an alignment
which are not power of two.
However, the percpu allocator never supported alignments which are not power
of two and has always behaved incorectly in thise case.
Commit 3ca45a4 "percpu: ensure requested alignment is power of two"
introduced a check which trigger a warning [1] when booting linux-next
on Xen. But in reality this bug was always present.
This can be fixed by replacing the call to __alloc_percpu with
alloc_percpu. The latter will use an alignment which are a power of two.
Commit 9c17d96500f7 ("xen/gntdev: Grant maps should not be subject to
NUMA balancing") set VM_IO flag to prevent grant maps from being
subjected to NUMA balancing.
It was discovered recently that this flag causes get_user_pages() to
always fail with -EFAULT.
We've got a delay loop waiting for secondary CPUs. That loop uses
loops_per_jiffy. However, loops_per_jiffy doesn't actually mean how
many tight loops make up a jiffy on all architectures. It is quite
common to see things like this in the boot log:
Calibrating delay loop (skipped), value calculated using timer
frequency.. 48.00 BogoMIPS (lpj=24000)
In my case I was seeing lots of cases where other CPUs timed out
entering the debugger only to print their stack crawls shortly after the
kdb> prompt was written.
Elsewhere in kgdb we already use udelay(), so that should be safe enough
to use to implement our timeout. We'll delay 1 ms for 1000 times, which
should give us a full second of delay (just like the old code wanted)
but allow us to notice that we're done every 1 ms.
[akpm@linux-foundation.org: simplifications, per Daniel] Link: http://lkml.kernel.org/r/1477091361-2039-1-git-send-email-dianders@chromium.org Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Brian Norris <briannorris@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a off-by-one in the "watchdog: qcom: add option for
standalone watchdog not in timer block" patch that causes the
following panic on boot:
Systemd on reboot enables shutdown watchdog that leaves the watchdog
device open to ensure that even if power down process get stuck the
platform reboots nonetheless.
The iamt_wdt is an alarm-only watchdog and can't reboot system, but the
FW will generate an alarm event reboot was completed in time, as the
watchdog is not automatically disabled during power cycle.
So we should request stop watchdog on reboot to eliminate wrong alarm
from the FW.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NMI handler doesn't call set_irq_regs(), it's set only by normal IRQ.
Thus get_irq_regs() returns NULL or stale registers snapshot with IP/SP
pointing to the code interrupted by IRQ which was interrupted by NMI.
NULL isn't a problem: in this case watchdog calls dump_stack() and
prints full stack trace including NMI. But if we're stuck in IRQ
handler then NMI watchlog will print stack trace without IRQ part at
all.
This patch uses registers snapshot passed into NMI handler as arguments:
these registers point exactly to the instruction interrupted by NMI.
Fixes: 55537871ef66 ("kernel/watchdog.c: perform all-CPU backtrace in case of hard lockup") Link: http://lkml.kernel.org/r/146771764784.86724.6006627197118544150.stgit@buzz Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Ulrich Obergfell <uobergfe@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not unlock/lock cifs_tcp_ses_lock while walking through ses
and tcon lists because it can corrupt list iterator pointers and
a tcon structure can be released if we don't hold an extra reference.
Fix it by moving a reconnect process to a separate delayed work
and acquiring a reference to every tcon that needs to be reconnected.
Also do not send an echo request on newly established connections.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dm_sm_metadata_create() we temporarily change the dm_space_map
operations from 'ops' (whose .destroy function deallocates the
sm_metadata) to 'bootstrap_ops' (whose .destroy function doesn't).
If dm_sm_metadata_create() fails in sm_ll_new_metadata() or
sm_ll_extend(), it exits back to dm_tm_create_internal(), which calls
dm_sm_destroy() with the intention of freeing the sm_metadata, but it
doesn't (because the dm_space_map operations is still set to
'bootstrap_ops').
Fix this by setting the dm_space_map operations back to 'ops' if
dm_sm_metadata_create() fails when it is set to 'bootstrap_ops'.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ecbfb9f118 ("dm raid: add raid level takeover support") moved the
configure_discard_support() call from raid_ctr() to raid_preresume().
Enabling/disabling discard _must_ happen during table load (through the
.ctr hook). Fix this regression by moving the
configure_discard_support() call back to raid_ctr().
It is required to hold the queue lock when calling blk_run_queue_async()
to avoid that a race between blk_run_queue_async() and
blk_cleanup_queue() is triggered.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In crypt_set_key(), if a failure occurs while replacing the old key
(e.g. tfm->setkey() fails) the key must not have DM_CRYPT_KEY_VALID flag
set. Otherwise, the crypto layer would have an invalid key that still
has DM_CRYPT_KEY_VALID flag set.
Signed-off-by: Ondrej Kozina <okozina@redhat.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return error code -EINVAL instead of 0, as is done elsewhere in
this function.
Fixes: e80d1c805a3b ("dm: do not override error code returned from dm_get_device()") Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dm_table_set_type() is used by a target to establish a DM table's
type (e.g. DM_TYPE_MQ_REQUEST_BASED in the case of DM multipath) the
DM core must go on to verify that the devices in the table are
compatible with the established type.
An earlier DM multipath table could have been build ontop of underlying
devices that were all using blk-mq. In that case, if that active
multipath table is replaced with an empty DM multipath table (that
reflects all paths have failed) then it is important that the
'all_blk_mq' state of the active table is transfered to the new empty DM
table. Otherwise dm-rq.c:dm_old_prep_tio() will incorrectly clone a
request that isn't needed by the DM multipath target when it is to issue
IO to an underlying blk-mq device.
Fixes: e83068a5 ("dm mpath: add optional "queue_mode" feature") Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meaning of the BLK_MQ_S_STOPPED flag is "do not call
.queue_rq()". Hence modify blk_mq_make_request() such that requests
are queued instead of issued if a queue has been stopped.
Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joonyoung Shim reported an interesting problem on his ARM octa-core
Odoroid-XU3 platform. During system suspend, dev_pm_opp_put_regulator()
was failing for a struct device for which dev_pm_opp_set_regulator() is
called earlier.
This happened because an earlier call to
dev_pm_opp_of_cpumask_remove_table() function (from cpufreq-dt.c file)
removed all the entries from opp_table->dev_list apart from the last CPU
device in the cpumask of CPUs sharing the OPP.
But both dev_pm_opp_set_regulator() and dev_pm_opp_put_regulator()
routines get CPU device for the first CPU in the cpumask. And so the OPP
core failed to find the OPP table for the struct device.
This patch attempts to fix this problem by returning a pointer to the
opp_table from dev_pm_opp_set_regulator() and using that as the
parameter to dev_pm_opp_put_regulator(). This ensures that the
dev_pm_opp_put_regulator() doesn't fail to find the opp table.
Note that similar design problem also exists with other
dev_pm_opp_put_*() APIs, but those aren't used currently by anyone and
so we don't need to update them for now.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ Viresh: Wrote commit log and tested on exynos 5250 ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Cc: <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vlastimil Babka pointed out that commit 479f854a207c ("mm, page_alloc:
defer debugging checks of pages allocated from the PCP") will allow the
per-cpu list counter to be out of sync with the per-cpu list contents if
a struct page is corrupted.
The consequence is an infinite loop if the per-cpu lists get fully
drained by free_pcppages_bulk because all the lists are empty but the
count is positive. The infinite loop occurs here
do {
batch_free++;
if (++migratetype == MIGRATE_PCPTYPES)
migratetype = 0;
list = &pcp->lists[migratetype];
} while (list_empty(list));
What the user sees is a bad page warning followed by a soft lockup with
interrupts disabled in free_pcppages_bulk().
This patch keeps the accounting in sync.
Fixes: 479f854a207c ("mm, page_alloc: defer debugging checks of pages allocated from the PCP") Link: http://lkml.kernel.org/r/20161202112951.23346-2-mgorman@techsingularity.net Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Christoph Lameter <cl@linux.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our system uses significantly more slab memory with memcg enabled with
the latest kernel. With 3.10 kernel, slab uses 2G memory, while with
4.6 kernel, 6G memory is used. The shrinker has problem. Let's see we
have two memcg for one shrinker. In do_shrink_slab:
1. Check cg1. nr_deferred = 0, assume total_scan = 700. batch size
is 1024, then no memory is freed. nr_deferred = 700
2. Check cg2. nr_deferred = 700. Assume freeable = 20, then
total_scan = 10 or 40. Let's assume it's 10. No memory is freed.
nr_deferred = 10.
The deferred share of cg1 is lost in this case. kswapd will free no
memory even run above steps again and again.
The fix makes sure one memcg's deferred share isn't lost.
Link: http://lkml.kernel.org/r/2414be961b5d25892060315fbb56bb19d81d0c07.1476227351.git.shli@fb.com Signed-off-by: Shaohua Li <shli@fb.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing a namespace we delete it from the subsystem namespaces
list with list_del_init which allows us to know if it is enabled or
not.
The problem is that list_del_init initialize the list next and does
not respect the RCU list-traversal we do on the IO path for locating
a namespace. Instead we need to use list_del_rcu which is allowed to
run concurrently with the _rcu list-traversal primitives (keeps list
next intact) and guarantees concurrent nvmet_find_naespace forward
progress.
By changing that, we cannot rely on ns->dev_link for knowing if the
namspace is enabled, so add enabled indicator entry to nvmet_ns for
that.
In the last ilen case, i was already increased, resulting in accessing out-
of-boundary entry of do_replace and blkaddr.
Fix to check ilen first to exit the loop.
Fixes: 2aa8fbb9693020 ("f2fs: refactor __exchange_data_block for speed up") Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct file_operations instance serving the f2fs/status debugfs file
lacks an initialization of its ->owner.
This means that although that file might have been opened, the f2fs module
can still get removed. Any further operation on that opened file, releasing
included, will cause accesses to unmapped memory.
Indeed, Mike Marshall reported the following:
BUG: unable to handle kernel paging request at ffffffffa0307430
IP: [<ffffffff8132a224>] full_proxy_release+0x24/0x90
<...>
Call Trace:
[] __fput+0xdf/0x1d0
[] ____fput+0xe/0x10
[] task_work_run+0x8e/0xc0
[] do_exit+0x2ae/0xae0
[] ? __audit_syscall_entry+0xae/0x100
[] ? syscall_trace_enter+0x1ca/0x310
[] do_group_exit+0x44/0xc0
[] SyS_exit_group+0x14/0x20
[] do_syscall_64+0x61/0x150
[] entry_SYSCALL64_slow_path+0x25/0x25
<...>
---[ end trace f22ae883fa3ea6b8 ]---
Fixing recursive fault but reboot is needed!
Fix this by initializing the f2fs/status file_operations' ->owner with
THIS_MODULE.
This will allow debugfs to grab a reference to the f2fs module upon any
open on that file, thus preventing it from getting removed.
Fixes: 902829aa0b72 ("f2fs: move proc files to debugfs") Reported-by: Mike Marshall <hubcap@omnibond.com> Reported-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently data journalling is incompatible with encryption: enabling both
at the same time has never been supported by design, and would result in
unpredictable behavior. However, users are not precluded from turning on
both features simultaneously. This change programmatically replaces data
journaling for encrypted regular files with ordered data journaling mode.
Background:
Journaling encrypted data has not been supported because it operates on
buffer heads of the page in the page cache. Namely, when the commit
happens, which could be up to five seconds after caching, the commit
thread uses the buffer heads attached to the page to copy the contents of
the page to the journal. With encryption, it would have been required to
keep the bounce buffer with ciphertext for up to the aforementioned five
seconds, since the page cache can only hold plaintext and could not be
used for journaling. Alternatively, it would be required to setup the
journal to initiate a callback at the commit time to perform deferred
encryption - in this case, not only would the data have to be written
twice, but it would also have to be encrypted twice. This level of
complexity was not justified for a mode that in practice is very rarely
used because of the overhead from the data journalling.
Solution:
If data=journaled has been set as a mount option for a filesystem, or if
journaling is enabled on a regular file, do not perform journaling if the
file is also encrypted, instead fall back to the data=ordered mode for the
file.
Rationale:
The intent is to allow seamless and proper filesystem operation when
journaling and encryption have both been enabled, and have these two
conflicting features gracefully resolved by the filesystem.
Fixes: 67cf5b09a46f ("ext4: add the basic function for inline data support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "ext4: sanity check the block and cluster size at mount
time" should prevent any problems, but in case the superblock is
modified while the file system is mounted, add an extra safety check
to make sure we won't overrun the allocated buffer.
Fix a large number of problems with how we handle mount options in the
superblock. For one, if the string in the superblock is long enough
that it is not null terminated, we could run off the end of the string
and try to interpret superblocks fields as characters. It's unlikely
this will cause a security problem, but it could result in an invalid
parse. Also, parse_options is destructive to the string, so in some
cases if there is a comma-separated string, it would be modified in
the superblock. (Fortunately it only happens on file systems with a
1k block size.)
The number of 'counters' elements needed in 'struct sg' is
super_block->s_blocksize_bits + 2. Presently we have 16 'counters'
elements in the array. This is insufficient for block sizes >= 32k. In
such cases the memcpy operation performed in ext4_mb_seq_groups_show()
would cause stack memory corruption.
Fixes: c9de560ded61f Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'border' variable is set to a value of 2 times the block size of the
underlying filesystem. With 64k block size, the resulting value won't
fit into a 16-bit variable. Hence this commit changes the data type of
'border' to 'unsigned int'.
The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.
When the flag PT_PTRACE_CAP was added the PTRACE_TRACEME path was
overlooked. This can result in incorrect behavior when an application
like strace traces an exec of a setuid executable.
Further PT_PTRACE_CAP does not have enough information for making good
security decisions as it does not report which user namespace the
capability is in. This has already allowed one mistake through
insufficient granulariy.
I found this issue when I was testing another corner case of exec and
discovered that I could not get strace to set PT_PTRACE_CAP even when
running strace as root with a full set of caps.
This change fixes the above issue with strace allowing stracing as
root a setuid executable without disabling setuid. More fundamentaly
this change allows what is allowable at all times, by using the correct
information in it's decision.
We truncated the possible read iterator to s_maxbytes in commit c2a9737f45e2 ("vfs,mm: fix a dead loop in truncate_inode_pages_range()"),
but our end condition handling was wrong: it's not an error to try to
read at the end of the file.
Reading past the end should return EOF (0), not EINVAL.
During exec dumpable is cleared if the file that is being executed is
not readable by the user executing the file. A bug in
ptrace_may_access allows reading the file if the executable happens to
enter into a subordinate user namespace (aka clone(CLONE_NEWUSER),
unshare(CLONE_NEWUSER), or setns(fd, CLONE_NEWUSER).
This problem is fixed with only necessary userspace breakage by adding
a user namespace owner to mm_struct, captured at the time of exec, so
it is clear in which user namespace CAP_SYS_PTRACE must be present in
to be able to safely give read permission to the executable.
The function ptrace_may_access is modified to verify that the ptracer
has CAP_SYS_ADMIN in task->mm->user_ns instead of task->cred->user_ns.
This ensures that if the task changes it's cred into a subordinate
user namespace it does not become ptraceable.
The function ptrace_attach is modified to only set PT_PTRACE_CAP when
CAP_SYS_PTRACE is held over task->mm->user_ns. The intent of
PT_PTRACE_CAP is to be a flag to note that whatever permission changes
the task might go through the tracer has sufficient permissions for
it not to be an issue. task->cred->user_ns is always the same
as or descendent of mm->user_ns. Which guarantees that having
CAP_SYS_PTRACE over mm->user_ns is the worst case for the tasks
credentials.
To prevent regressions mm->dumpable and mm->user_ns are not considered
when a task has no mm. As simply failing ptrace_may_attach causes
regressions in privileged applications attempting to read things
such as /proc/<pid>/stat
Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Cyrill Gorcunov <gorcunov@openvz.org> Fixes: 8409cca70561 ("userns: allow ptrace from non-init user namespaces") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bdev->bd_contains is not stable before calling __blkdev_get().
When __blkdev_get() is called on a parition with ->bd_openers == 0
it sets
bdev->bd_contains = bdev;
which is not correct for a partition.
After a call to __blkdev_get() succeeds, ->bd_openers will be > 0
and then ->bd_contains is stable.
When FMODE_EXCL is used, blkdev_get() calls
bd_start_claiming() -> bd_prepare_to_claim() -> bd_may_claim()
This call happens before __blkdev_get() is called, so ->bd_contains
is not stable. So bd_may_claim() cannot safely use ->bd_contains.
It currently tries to use it, and this can lead to a BUG_ON().
This happens when a whole device is already open with a bd_holder (in
use by dm in my particular example) and two threads race to open a
partition of that device for the first time, one opening with O_EXCL and
one without.
The thread that doesn't use O_EXCL gets through blkdev_get() to
__blkdev_get(), gains the ->bd_mutex, and sets bdev->bd_contains = bdev;
Immediately thereafter the other thread, using FMODE_EXCL, calls
bd_start_claiming() from blkdev_get(). This should fail because the
whole device has a holder, but because bdev->bd_contains == bdev
bd_may_claim() incorrectly reports success.
This thread continues and blocks on bd_mutex.
The first thread then sets bdev->bd_contains correctly and drops the mutex.
The thread using FMODE_EXCL then continues and when it calls bd_may_claim()
again in:
BUG_ON(!bd_may_claim(bdev, whole, holder));
The BUG_ON fires.
Fix this by removing the dependency on ->bd_contains in
bd_may_claim(). As bd_may_claim() has direct access to the whole
device, it can simply test if the target bdev is the whole device.
If you have a process that has set itself to be non-dumpable, and it
then undergoes exec(2), any CLOEXEC file descriptors it has open are
"exposed" during a race window between the dumpable flags of the process
being reset for exec(2) and CLOEXEC being applied to the file
descriptors. This can be exploited by a process by attempting to access
/proc/<pid>/fd/... during this window, without requiring CAP_SYS_PTRACE.
The race in question is after set_dumpable has been (for get_link,
though the trace is basically the same for readlink):
Which will return 0, during the race window and CLOEXEC file descriptors
will still be open during this window because do_close_on_exec has not
been called yet. As a result, the ordering of these calls should be
reversed to avoid this race window.
This is of particular concern to container runtimes, where joining a
PID namespace with file descriptors referring to the host filesystem
can result in security issues (since PRCTL_SET_DUMPABLE doesn't protect
against access of CLOEXEC file descriptors -- file descriptors which may
reference filesystem objects the container shouldn't have access to).
Cc: dev@opencontainers.org Reported-by: Michael Crosby <crosbymichael@gmail.com> Signed-off-by: Aleksa Sarai <asarai@suse.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user namespace support was merged the need to prevent
ptrace from revealing the contents of an unreadable executable
was overlooked.
Correct this oversight by ensuring that the executed file
or files are in mm->user_ns, by adjusting mm->user_ns.
Use the new function privileged_wrt_inode_uidgid to see if
the executable is a member of the user namespace, and as such
if having CAP_SYS_PTRACE in the user namespace should allow
tracing the executable. If not update mm->user_ns to
the parent user namespace until an appropriate parent is found.
Reported-by: Jann Horn <jann@thejh.net> Fixes: 9e4a36ece652 ("userns: Fail exec for suid and sgid binaries with ids outside our user namespace.") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 951555856b88 ("Btrfs: send, don't bug on inconsistent snapshots")
removed some BUG_ON() statements (replacing them with returning errors
to user space and logging error messages) when a snapshot is in an
inconsistent state due to failures to update a delayed inode item (ENOMEM
or ENOSPC) after adding/updating/deleting references, xattrs or file
extent items.
However there is a case, when no errors happen, where a file extent item
can be modified without having the corresponding inode item updated. This
case happens during balance under very specific timings, when relocation
is in the stage where it updates data pointers and a leaf that contains
file extent items is COWed. When that happens file extent items get their
disk_bytenr field updated to a new value that reflects the post relocation
logical address of the extent, without updating their respective inode
items (as there is nothing that needs to be updated on them). This is
performed at relocation.c:replace_file_extents() through
relocation.c:btrfs_reloc_cow_block().
So make an incremental send deal with this case and don't do any processing
for a file extent item that got its disk_bytenr field updated by relocation,
since the extent's data is the same as the one pointed by the file extent
item in the parent snapshot.
After the recent commit mentioned above this case resulted in EIO errors
returned to user space (and an error message logged to dmesg/syslog) when
doing an incremental send, while before it, it resulted in hitting a
BUG_ON leading to the following trace:
Really there's lots of things that can go wrong here, kill all the
BUG_ON()'s and replace the logic ones with ASSERT()'s and return EIO
instead.
Signed-off-by: Josef Bacik <jbacik@fb.com>
[ switched to btrfs_err, errors go to common label ] Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btrfs_show_devname() is using the device_list_mutex, sometimes
a call to blkdev_put() leads vfs calling into this func. So
call blkdev_put() outside of device_list_mutex, as of now.
The extent buffer 'next' needs to be free'd conditionally.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btrfs_rm_device frees the block device but then re-opens it using
the saved device name. A race exists between the close and the
re-open that allows the block size to be changed. The result
is getting stuck forever in the reclaim loop in __getblk_slow.
This patch moves the superblock cleanup before closing the block
device, which is also consistent with other callers. We also don't
need a private copy of dev_name as the whole routine operates under
the uuid_mutex.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't track the reloc roots in any sort of normal way, so the only way the
root/commit_root nodes get free'd is if the relocation finishes successfully and
the reloc root is deleted. Fix this by free'ing them in free_reloc_roots.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When relocating tree blocks, we firstly get block information from
back references in the extent tree, we then search fs tree to try to
find all parents of a block.
However, if fs tree is corrupted, eg. if there're some missing
items, we could come across these WARN_ONs and BUG_ONs.
This makes us print some error messages and return gracefully
from balance.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we allow inconsistence about mixed flag
(BTRFS_BLOCK_GROUP_METADATA | BTRFS_BLOCK_GROUP_DATA).
We'd get ENOSPC if block group has mixed flag and btrfs doesn't.
If that happens, we have one space_info with mixed flag and another
space_info only with BTRFS_BLOCK_GROUP_METADATA, and
global_block_rsv.space_info points to the latter one, but all bytes
from block_group contributes to the mixed space_info, thus all the
allocation will fail with ENOSPC.
This adds a check for the above case.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
[ updated message ] Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So we can read a btree block via readahead or intentional read,
and we can end up with a memory leak when something happens as
follows,
1) readahead starts to read block A but does not wait for read
completion,
2) btree_readpage_end_io_hook finds that block A is corrupted,
and it needs to clear all block A's pages' uptodate bit.
3) meanwhile an intentional read kicks in and checks block A's
pages' uptodate to decide which page needs to be read.
4) when some pages have the uptodate bit during 3)'s check so
3) doesn't count them for eb->io_pages, but they are later
cleared by 2) so we has to readpage on the page, we get
the wrong eb->io_pages which results in a memory leak of
this block.
This fixes the problem by firstly getting all pages's locking and
then checking pages' uptodate bit.
t1(readahead) t2(readahead endio) t3(the following read)
read_extent_buffer_pages end_bio_extent_readpage
for pg in eb: for page 0,1,2 in eb:
if pg is uptodate: btree_readpage_end_io_hook(pg)
num_reads++ if uptodate:
eb->io_pages = num_reads SetPageUptodate(pg) _______________
for pg in eb: for page 3 in eb: read_extent_buffer_pages
if pg is NOT uptodate: btree_readpage_end_io_hook(pg) for pg in eb:
__extent_read_full_page(pg) sanity check reports something wrong if pg is uptodate:
clear_extent_buffer_uptodate(eb) num_reads++
for pg in eb: eb->io_pages = num_reads
ClearPageUptodate(page) _______________
for pg in eb:
if pg is NOT uptodate:
__extent_read_full_page(pg)
So t3's eb->io_pages is not consistent with the number of pages it's reading,
and during endio(), atomic_dec_and_test(&eb->io_pages) will get a negative
number so that we're not able to free the eb.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9] Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit [64047d7f4912 ALSA: hda - ignore the assoc and seq when comparing
pin configurations] intented to ignore both seq and assoc at pin
comparing, but it only ignored seq. So that commit may still fail to
match pins on some machines.
Change the bitmask to also ignore assoc.
v2: Use macro to do bit masking.
Thanks to Hui Wang for the analysis.
Fixes: 64047d7f4912 ("ALSA: hda - ignore the assoc and seq when comparing...") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP Z1 Gen3 AiO with Conexant codec doesn't give an unsolicited event
to the headset mic pin upon the jack plugging, it reports only to the
headphone pin. It results in the missing mic switching. Let's fix up
by simply gating the jack event.
More and more pin configurations have been adding to the pin quirk
table, lots of them are only different from assoc and seq, but they
all apply to the same QUIRK_FIXUP, if we don't compare assoc and seq
when matching pin configurations, it will greatly reduce the pin
quirk table size.
We have tested this change on a couple of Dell laptops, it worked
well.
Sampling rate changes after first set one are not reflected to the
hardware, while driver and ALSA think the rate has been changed.
Fix the problem by properly stopping the interface at the beginning of
prepare call, allowing new rate to be set to the hardware. This keeps
the hardware in sync with the driver.
The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the
following warning.
[ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072),
cval->res is probably wrong.
[ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val =
4608/7680/1
Adding it to the list of devices in volume_control_quirks makes it work
properly, fixing related typo.
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
