John Crispin [Mon, 20 Oct 2014 11:19:21 +0000 (11:19 +0000)]
hostapd: Add wpa_psk_file option to netifd.sh
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
John Crispin [Mon, 20 Oct 2014 06:29:05 +0000 (06:29 +0000)]
failsafe-mode: print short help on commandline
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/
http://patchwork.openwrt.org/patch/3553/
Jo-Philipp Wich [Sun, 19 Oct 2014 17:46:37 +0000 (17:46 +0000)]
x86_64: use default block2mtd timeout of 5s
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Felix Fietkau [Sat, 18 Oct 2014 19:25:24 +0000 (19:25 +0000)]
toolchain: fix binutils broken symlink
The Makefile for binutils creates a broken symlink to "binutils-linaro" in
"trunk/build_dir/toolchain-<target>_gcc-4.9-linaro_uClibc-0.9.33.2".
Modify the Makefile to point the symlink to the correct directory.
Rafał Miłecki [Thu, 16 Oct 2014 20:52:22 +0000 (20:52 +0000)]
bcm53xx: hack UBI to erase all dirty blocks left by CFE
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
John Crispin [Wed, 15 Oct 2014 17:55:13 +0000 (17:55 +0000)]
default_postinst() fix wrong call of group_add
[base-files] default_postinst() fix wrong call of group_add
after 12bae65d07d29854204715cebc1ef1eae237fd9b group_add is
always called. shell scripting can be tricky...
John Crispin [Tue, 14 Oct 2014 19:01:30 +0000 (19:01 +0000)]
base-files: default_postinst() force clear luci-indexcache
Inside every LuCI package you need to clear luci-indexcache and
sometimes when installing non LuCI pacakges it's also needed to clear
it. Easier put it into default_postinst().
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 42923
John Crispin [Tue, 14 Oct 2014 19:01:21 +0000 (19:01 +0000)]
wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILL
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
John Crispin [Tue, 14 Oct 2014 19:01:10 +0000 (19:01 +0000)]
lantiq xway: generate ramdisk image by default
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42920
John Crispin [Tue, 14 Oct 2014 12:21:41 +0000 (12:21 +0000)]
ar71xx: fix seama factory type image generation.
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
John Crispin [Tue, 14 Oct 2014 12:21:36 +0000 (12:21 +0000)]
ar71xx: qihoo-c301: reset imageNtrynum after each successful boot.
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
John Crispin [Tue, 14 Oct 2014 12:21:11 +0000 (12:21 +0000)]
scripts: fix wrong usage of '==' operator
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
John Crispin [Tue, 14 Oct 2014 10:33:07 +0000 (10:33 +0000)]
ar71xx: Fix LED definitions for the DRAGINO2 board
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
John Crispin [Mon, 13 Oct 2014 19:41:27 +0000 (19:41 +0000)]
scripts/feeds: handle missing/broken feeds better
pts/feeds update -a" can fail rather silently for feeds using git, as
the script does not pause when updating a feed fails. Instead it prints the
error message and calmly continues to the next feed. It is very easy to
overlook update errors with the feeds updated first, as their text scrolls
rapidly away from the screen.
This behaviour has not been a big problem with svn feeds, as svn update stops
with a conflict message and interactively forces the user to resolve or
postpone the conflict. In any case the svn error is noticed by the user.
Majority of the feeds use now git, so this silent failure can affect users
doing private builds in an increasing amount.
Below is an example of update failing and script continuing:
perus@v1404:/Openwrt/barrier$ ./scripts/feeds update -a
Updating feed 'packages' from
'https://github.com/openwrt/packages.git;for-14.07' ...
remote: Counting objects: 17, done.
remote: Compressing objects: 100% (15/15), done.
remote: Total 17 (delta 10), reused 8 (delta 1)
Unpacking objects: 100% (17/17), done.
From https://github.com/openwrt/packages 62031da..dc26009 for-14.07 -> origin/for-14.07
Updating 62031da..dc26009
error: Your local changes to the following files would be overwritten by merge:
utils/collectd/Makefile
Please, commit your changes or stash them before you can merge.
Aborting
failed.
Updating feed 'luci' from 'http://git.openwrt.org/project/luci.git;luci-0.12' ...
Already up-to-date.
Create index file './feeds/luci.index'
Updating feed 'routing' from
'https://github.com/openwrt-routing/packages.git;for-14.07' ...
...
The script prints "failed.", but does not break the updating process. The
"update_feed" function returns an error code 1, but that value is not checked
in the "update" function, which continues to the next feed.
Return 1 as error:
https://dev.openwrt.org/browser/trunk/scripts/feeds#L547
Call to update_feed without any error monitoring:
https://dev.openwrt.org/browser/trunk/scripts/feeds#L585
The included patch makes the feeds script to stop updating after failing to
update a feed.
The script continues to the refresh_config step despite a possible failure in
updating, so the stopping action just prevents the other feeds from updating
and makes the error more clearly visible.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 42891
projects / thirdparty / openwrt.git / log
