If HW Channel (HWC) is not responding, reduce the waiting time, so further
steps will fail quickly.
This will prevent getting stuck for a long time (30 minutes or more), for
example, during unloading while HWC is not responding.
The calculation formula for nominal bit rate of classical CAN is the same as
that of nominal bit rate of CANFD on the RZ/G3E and R-Car Gen4 SoCs
compared to other SoCs. Update nominal bit rate constants.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://patch.msgid.link/20250908120940.147196-2-biju.das.jz@bp.renesas.com
[mkl: slightly improve wording of commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
during entropy evaluation, if the generated samples fail
any statistical test, then, all of the bits will be discarded,
and a second set of samples will be generated and tested.
the entropy delay interval should be doubled before performing the
retry.
also, ctrlpriv->rng4_sh_init and inst_handles both reads RNG DRNG
status register, but only inst_handles is updated before every retry.
so only check inst_handles and removing ctrlpriv->rng4_sh_init
payload_size field of the request header is incorrectly calculated using
sizeof(req). Since 'req' is a pointer (struct hsti_request *), sizeof(req)
returns the size of the pointer itself (e.g., 8 bytes on a 64-bit system),
rather than the size of the structure it points to. This leads to an
incorrect payload size being sent to the Platform Security Processor (PSP),
potentially causing the HSTI query command to fail.
Fix this by using sizeof(*req) to correctly calculate the size of the
struct hsti_request.
Signed-off-by: Yunseong Kim <ysk@kzalloc.com> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>> --- Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
dw_pcie_edma_irq_verify() is supposed to verify the eDMA IRQs in devicetree
by fetching them using either 'dma' or 'dmaX' IRQ names. Former is used
when the platform uses a single IRQ for all eDMA channels and latter is
used when the platform uses separate IRQ per channel. But currently,
dw_pcie_edma_irq_verify() bails out early if edma::nr_irqs is 1, i.e., when
a single IRQ is used. This gives an impression that the driver could work
with any single IRQ in devicetree, not necessarily with name 'dma'.
But dw_pcie_edma_irq_vector(), which actually requests the IRQ, does
require the single IRQ to be named as 'dma'. So this creates inconsistency
between dw_pcie_edma_irq_verify() and dw_pcie_edma_irq_vector().
Thus, to fix this inconsistency, make sure dw_pcie_edma_irq_verify() also
verifies the single IRQ name by removing the bail out code.
Fix the issue of max_timeout being calculated larger than actual value.
The calculation result of freq / (S3C2410_WTCON_PRESCALE_MAX + 1) /
S3C2410_WTCON_MAXDIV is smaller than the actual value because the remainder
is discarded during the calculation process. This leads to a larger
calculated value for max_timeout compared to the actual settable value.
To resolve this issue, the order of calculations in the computation process
has been adjusted.
The Asus Z13 folio has a multitouch touchpad that needs to bind
to the hid-multitouch driver in order to work properly. So bind
it to the HID_GROUP_GENERIC group to release the touchpad and
move it to the bottom so that the comment applies to it.
While at it, change the generic KEYBOARD3 name to Z13_FOLIO.
Reviewed-by: Luke D. Jones <luke@ljones.dev> Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
netdev_WARN() uses WARN/WARN_ON to print a backtrace along with
file and line information. In this case, udp_tunnel_nic_register()
returning an error is just a failed operation, not a kernel bug.
udp_tunnel_nic_register() can fail due to a memory allocation
failure (kzalloc() or udp_tunnel_nic_alloc()).
This is a normal runtime error and not a kernel bug.
Replace netdev_WARN() with netdev_warn() accordingly.
Usually the autodefer helpers in lib.sh are expected to be run in context
where success is the expected outcome. However when using them for feature
detection, failure can legitimately occur. But the failed command still
schedules a cleanup, which will likely fail again.
Instead, only schedule deferred cleanup when the positive command succeeds.
This way of organizing the cleanup has the added benefit that now the
return code from these functions reflects whether the command passed.
tcp_recvmsg_dmabuf can export the following errors:
- EFAULT when linear copy fails
- ETOOSMALL when cmsg put fails
- ENODEV if one of the frags is readable
- ENOMEM on xarray failures
But they are all ignored and replaced by EFAULT in the caller
(tcp_recvmsg_locked). Expose real error to the userspace to
add more transparency on what specifically fails.
In non-devmem case (skb_copy_datagram_msg) doing `if (!copied)
copied=-EFAULT` is ok because skb_copy_datagram_msg can return only EFAULT.
Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Mina Almasry <almasrymina@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250910162429.4127997-1-sdf@fomichev.me Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 8139too is probing and 8139TOO_PIO=y it will call pci_iomap_range()
and from there __pci_ioport_map() for the PCI IO space.
If HAS_IOPORT_MAP=n and NO_GENERIC_PCI_IOPORT_MAP=n, like it is on my
m68k config, __pci_ioport_map() becomes NULL, pci_iomap_range() will
always fail and the driver will complain it couldn't map the PIO space
and return an error.
NO_IOPORT_MAP seems to cover the case where what 8139too is trying
to do cannot ever work so make 8139TOO_PIO depend on being it false
and avoid creating an unusable driver.
All of the x86 KVM guest types (VMX, SEV and TDX) do some special context
tracking when entering guests. This means that the actual guest entry
sequence must be noinstr.
Part of entering a TDX guest is passing a physical address to the TDX
module. Right now, that physical address is stored as a 'struct page'
and converted to a physical address at guest entry. That page=>phys
conversion can be complicated, can vary greatly based on kernel
config, and it is definitely _not_ a noinstr path today.
There have been a number of tinkering approaches to try and fix this
up, but they all fall down due to some part of the page=>phys
conversion infrastructure not being noinstr friendly.
Precalculate the page=>phys conversion and store it in the existing
'tdx_vp' structure. Use the new field at every site that needs a
tdvpr physical address. Remove the now redundant tdx_tdvpr_pa().
Remove the __flatten remnant from the tinkering.
Note that only one user of the new field is actually noinstr. All
others can use page_to_phys(). But, they might as well save the effort
since there is a pre-calculated value sitting there for them.
[ dhansen: rewrite all the text ]
Signed-off-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kiryl Shutsemau <kas@kernel.org> Tested-by: Farrah Chen <farrah.chen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit b2798ba0b876 ("KVM: X86: Choose qspinlock when dedicated
physical CPUs are available") states that when PV_DEDICATED=1
(vCPU has dedicated pCPU), qspinlock should be preferred regardless of
PV_UNHALT. However, the current implementation doesn't reflect this: when
PV_UNHALT=0, we still use virt_spin_lock() even with dedicated pCPUs.
This is suboptimal because:
1. Native qspinlocks should outperform virt_spin_lock() for dedicated
vCPUs irrespective of HALT exiting
2. virt_spin_lock() should only be preferred when vCPUs may be preempted
(non-dedicated case)
So reorder the PV spinlock checks to:
1. First handle dedicated pCPU case (disable virt_spin_lock_key)
2. Second check single CPU, and nopvspin configuration
3. Only then check PV_UNHALT support
This ensures we always use native qspinlock for dedicated vCPUs, delivering
pretty performance gains at high contention levels.
Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Tested-by: Wangyang Guo <wangyang.guo@intel.com> Link: https://lore.kernel.org/r/20250722110005.4988-1-lirongqing@baidu.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
But the icmp reject 'netdev' family versions will reply to icmp
dst-unreach errors, unlike icmp_send() and icmp6_send() which are used
by the inet family implementation (and internally by the REJECT target).
Check for the icmp(6) type and do not respond if its an unreachable error.
Without this, something like 'ip protocol icmp reject', when used
in a netdev chain attached to 'lo', cause a packet loop.
Same for two hosts that both use such a rule: each error packet
will be replied to.
Such situation persist until the (bogus) rule is amended to ratelimit or
checks the icmp type before the reject statement.
As the inet versions don't do this make the netdev ones follow along.
To ensure the proper functioning of the jump_label test module, this patch
adds support for the R_OR1K_32_PCREL relocation type for any modules. The
implementation calculates the PC-relative offset by subtracting the
instruction location from the target value and stores the result at the
specified location.
The test always returns success even if some tests were modified to
fail. Fix by converting the test to use the appropriate library
functions instead of using its own functions.
Originally, the 'amd_pmf_get_custom_bios_inputs()' function was written
under the assumption that the BIOS would only send a single pending
request for the driver to process. However, following OEM enablement, it
became clear that multiple pending requests for custom BIOS inputs might
be sent at the same time, a scenario that the current code logic does not
support when it comes to handling multiple custom BIOS inputs.
To address this, the code logic needs to be improved to not only manage
multiple simultaneous custom BIOS inputs but also to ensure it is scalable
for future additional inputs.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com> Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com> Tested-by: Yijun Shen <Yijun.Shen@Dell.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://patch.msgid.link/20250901110140.2519072-3-Shyam-sundar.S-k@amd.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change "ret" from u8 to int type in redrat3_enable_detector() to store
negative error codes or zero returned by redrat3_send_cmd() and
usb_submit_urb() - this better aligns with the coding standards and
maintains code consistency.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcnal-test.sh already includes lib.sh, use relevant helpers
instead of sleeping. Replace sleep after starting nettest
as a server with wait_local_port_listen.
The upstream mesa copy of the GPU regs has shifted more things to reg64
instead of seperate 32b HI/LO reg32's. This works better with the "new-
style" c++ builders that mesa has been migrating to for a6xx+ (to better
handle register shuffling between gens), but it leaves the C builders
with missing _HI/LO builders.
So handle the special case of reg64, automatically generating the
missing _HI/LO builders.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673559/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver for the Rockchip MIPI CSI-2 DPHY uses GRF register offset
value 0 to sort out undefined registers. However, the RK3588 CSIDPHY GRF
this offset is perfectly fine (in fact, register 0 is the only one in
this register file).
Introduce a boolean variable to indicate valid registers and allow writes
to register 0.
When compiled without CONFIG_VIDEO the architecture specific
implementations of video_is_primary_device() include prototypes and
assume that video-common.c will be linked. Guard against this so that the
fallback inline implementation that returns false will be used when
compiled without CONFIG_VIDEO.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202506221312.49Fy1aNA-lkp@intel.com/ Link: https://lore.kernel.org/r/20250811162606.587759-2-superm1@kernel.org Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable support for data lane rates between 80-160 Mbps cdns dphy
as mentioned in TRM [0] by setting the pll_opdiv field to 16.
This change enables lower resolutions like 640x480 at 60Hz.
[0]: https://www.ti.com/lit/zip/spruil1
(Table 12-552. DPHY_TX_PLL_CTRL Register Field Descriptions)
In hidden SSID we have separate BSS entries for the beacon and for the
probe response(s).
The BSS entry time stamps represent the age of the BSS;
when was the last time we heard the BSS.
When we receive a beacon of a hidden SSID it means that we heard that
BSS, so it makes sense to indicate that in the probe response entries.
Do that.
Since commit af153bb63a33 ("vfs: catch invalid modes in may_open()")
requires any inode be one of S_IFDIR/S_IFLNK/S_IFREG/S_IFCHR/S_IFBLK/
S_IFIFO/S_IFSOCK type, use S_IFREG for $Extend records.
Address the issue where the host does not send adapt to the device after
PA_Init success. Ensure the adapt process is correctly initiated for
devices with IP version MT6899 and above, resolving communication issues
between the host and device.
Signed-off-by: Alice Chao <alice.chao@mediatek.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable auto-hibern8 during power mode transitions to prevent unintended
entry into auto-hibern8. Restore the original auto-hibern8 timer value
after completing the power mode change to maintain system stability and
prevent potential issues during power state transitions.
Signed-off-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Refine the system power management (PM) flow by skipping low power mode
(LPM) and MTCMOS settings if runtime PM is already applied. Prevent
redundant operations to ensure a more efficient PM process.
Signed-off-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 88e1510 PHY has an erratum where the phy downshift counter is not
cleared after phy being suspended(BMCR_PDOWN set) and then later
resumed(BMCR_PDOWN cleared). This can cause the gigabit link to
intermittently downshift to a lower speed.
Disabling and re-enabling the downshift feature clears the counter,
allowing the PHY to retry gigabit link negotiation up to the programmed
retry count times before downshifting. This behavior has been observed
on copper links.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com> Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250906-marvell_fix-v2-1-f6efb286937f@altera.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Improve the recovery process for hibernation exit failures. Trigger the
error handler and break the suspend operation to ensure effective
recovery from hibernation errors. Activate the error handling mechanism
by ufshcd_force_error_recovery and scheduling the error handler work.
Signed-off-by: Peter Wang <peter.wang@mediatek.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Resolve the issue of unbalanced IRQ enablement by setting the
'is_mcq_intr_enabled' flag after the first successful IRQ enablement.
Ensure proper tracking of the IRQ state and prevent potential mismatches
in IRQ handling.
Signed-off-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disabling the AES core in Shared ICE is not supported during power
collapse for UFS Host Controller v5.0, which may lead to data errors
after Hibern8 exit. To comply with hardware programming guidelines and
avoid this issue, issue a sync reset to ICE upon power collapse exit.
Hence follow below steps to reset the ICE upon exiting power collapse
and align with Hw programming guide.
a. Assert the ICE sync reset by setting both SYNC_RST_SEL and
SYNC_RST_SW bits in UFS_MEM_ICE_CFG
b. Deassert the reset by clearing SYNC_RST_SW in UFS_MEM_ICE_CFG
Signed-off-by: Palash Kambar <quic_pkambar@quicinc.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Improve the recovery process for failed resume operations. Log the
device's power status and return 0 if both resume and recovery fail to
prevent I/O hang.
Signed-off-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When many ADD_ADDR need to be sent, it can take some time to send each
of them, and create new subflows. Some CIs seem to occasionally have
issues with these tests, especially with "debug" kernels.
Two subtests will now run for a slightly longer time: the last two where
3 or more ADD_ADDR are sent during the test.
On DGFX, during init_post_hwconfig() step, we are reinitializing
CTB BO in VRAM and we have to replace cleanup action to disable CT
communication prior to release of underlying BO.
But that introduces some discrepancy between DGFX and iGFX, as for
iGFX we keep previously added disable CT action that would be called
during unwind much later.
To keep the same flow on both types of platforms, always replace old
cleanup action and register new one.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Satyanarayana K V P <satyanarayana.k.v.p@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com> Link: https://lore.kernel.org/r/20250908102053.539-2-michal.wajdeczko@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of writing the first byte of the infoframe (and hoping that the
rest is default / zeroes), hook Audio InfoFrame support into the
write_infoframe / clear_infoframes callbacks and use
drm_atomic_helper_connector_hdmi_update_audio_infoframe() to write the
frame.
The OmniVision OG01A1B image sensor is a monochrome sensor, it supports
8-bit and 10-bit RAW output formats only.
That said the planar greyscale Y8/Y10 media formats are more appropriate
for the sensor instead of the originally and arbitrary selected SGRBG one,
since there is no red, green or blue color components.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The datasheet of ov08x40 doesn't match the hardware behavior.
0x3821[2] == 1 is the original state and 0 the horizontal flip enabled.
Signed-off-by: Hao Yao <hao.yao@intel.com> Reviewed-by: Hans de Goede <hansg@kernel.org> Tested-by: Hans de Goede <hansg@kernel.org> # ThinkPad X1 Carbon Gen 12 & Gen 13 Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the test allocates BAR sizes according to fixed table bar_size.
This does not work with controllers which have fixed size BARs that are
smaller than the requested BAR size. One such controller is Renesas R-Car
V4H PCIe controller, which has BAR4 size limited to 256 bytes, which is
much less than one of the BAR size, 131072 currently requested by this
test. A lot of controllers drivers in-tree have fixed size BARs, and they
do work perfectly fine, but it is only because their fixed size is larger
than the size requested by pci-epf-test.c
Adjust the test such that in case a fixed size BAR is detected, the fixed
BAR size is used, as that is the only possible option.
This helps with test failures reported as follows:
pci_epf_test pci_epf_test.0: requested BAR size is larger than fixed size
pci_epf_test pci_epf_test.0: Failed to allocate space for BAR4
Recent changes to make netlink socket memory accounting must
have broken the implicit assumption of the netlink-dump test
that we can fit exactly 64 dumps into the socket. Handle the
failure mode properly, and increase the dump count to 80
to make sure we still run into the error condition if
the default buffer size increases in the future.
Add the missing linking of NAPIs to netdev queues when enabling
interrupt vectors in order to support NAPI configuration and
interfaces requiring get_rx_queue()->napi to be set (like XSk
busy polling).
As currently, idpf_vport_{start,stop}() is called from several flows
with inconsistent RTNL locking, we need to synchronize them to avoid
runtime assertions. Notably:
* idpf_{open,stop}() -- regular NDOs, RTNL is always taken;
* idpf_initiate_soft_reset() -- usually called under RTNL;
* idpf_init_task -- called from the init work, needs RTNL;
* idpf_vport_dealloc -- called without RTNL taken, needs it.
Expand common idpf_vport_{start,stop}() to take an additional bool
telling whether we need to manually take the RTNL lock.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> # helper Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Ramu R <ramu.r@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CP_ALWAYS_ON counter falls under GX domain which is collapsed during
IFPC. So switch to GMU_ALWAYS_ON counter for any CPU reads since it is
not impacted by IFPC. Both counters are clocked by same xo clock source.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673373/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some special registers which are accessible even when GX power
domain is collapsed during an IFPC sleep. Accessing these registers
wakes up GPU from power collapse and allow programming these registers
without additional handshake with GMU. This patch adds support for this
special register write sequence.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673368/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, misc_deregister() uses list_del() to remove the device
from the list. After list_del(), the list pointers are set to
LIST_POISON1 and LIST_POISON2, which may help catch use-after-free bugs,
but does not reset the list head.
If misc_deregister() is called more than once on the same device,
list_empty() will not return true, and list_del() may be called again,
leading to undefined behavior.
Replace list_del() with list_del_init() to reinitialize the list head
after deletion. This makes the code more robust against double
deregistration and allows safe usage of list_empty() on the miscdevice
after deregistration.
[ Note, this seems to keep broken out-of-tree drivers from doing foolish
things. While this does not matter for any in-kernel drivers,
external drivers could use a bit of help to show them they shouldn't
be doing stuff like re-registering misc devices - gregkh ]
Update Adreno 623's dt-binding to remove smmu_clk which is not required
for this GMU.
Signed-off-by: Jie Zhang <quic_jiezh@quicinc.com> Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/672455/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Not all FRAM chips have a device ID and implement the corresponding read
command. For such chips this led to the following error on module
loading:
at25 spi2.0: Error: no Cypress FRAM (id 00)
The device ID contains the memory size, so devices without this ID are
supported now by setting the size manually in Devicetree using the
"size" property.
Tested with FM25L16B and "size = <2048>;":
at25 spi2.0: 2 KByte fm25 fram, pagesize 4096
According to Infineon/Cypress datasheets, these FRAMs have a device ID:
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Starting with commit f99508074e78 ("PM: domains: Detach on
device_unbind_cleanup()"), there is no longer a need to call
dev_pm_domain_detach() in the bus remove function. The
device_unbind_cleanup() function now handles this to avoid
invoking devres cleanup handlers while the PM domain is
powered off, which could otherwise lead to failures as
described in the above-mentioned commit.
Drop the explicit dev_pm_domain_detach() call and rely instead
on the flags passed to dev_pm_domain_attach() to power off the
domain.
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints").
Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.
The "usxgmii" phy-mode that the Felix switch ports support on LS1028A is
not quite USXGMII, it is defined by the USXGMII multiport specification
document as 10G-QXGMII. It uses the same signaling as USXGMII, but it
multiplexes 4 ports over the link, resulting in a maximum speed of 2.5G
per port.
This change is needed in preparation for the lynx-10g SerDes driver on
LS1028A, which will make a more clear distinction between usxgmii
(supported on lane 0) and 10g-qxgmii (supported on lane 1). These
protocols have their configuration in different PCCR registers (PCCRB vs
PCCR9).
Continue parsing and supporting single-port-per-lane USXGMII when found
in the device tree as usual (because it works), but add support for
10G-QXGMII too. Using phy-mode = "10g-qxgmii" will be required when
modifying the device trees to specify a "phys" phandle to the SerDes
lane. The result when the "phys" phandle is present but the phy-mode is
wrong is undefined.
The only PHY driver in known use with this phy-mode, AQR412C, will gain
logic to transition from "usxgmii" to "10g-qxgmii" in a future change.
Prepare the driver by also setting PHY_INTERFACE_MODE_10G_QXGMII in
supported_interfaces when PHY_INTERFACE_MODE_USXGMII is there, to
prevent breakage with existing device trees.
devmem test fails on NIPA. Most likely we get skb(s) with readable
frags (why?) but the failure manifests as an OOM. The OOM happens
because ncdevmem spams the following message:
recvmsg ret=-1
recvmsg: Bad address
As of today, ncdevmem can't deal with various reasons of EFAULT:
- falling back to regular recvmsg for non-devmem skbs
- increasing ctrl_data size (can't happen with ncdevmem's large buffer)
Exit (cleanly) with error when recvmsg returns EFAULT. This should at
least cause the test to cleanup its state.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Mina Almasry <almasrymina@google.com> Link: https://patch.msgid.link/20250904182710.1586473-1-sdf@fomichev.me Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
There is a `scale` sysfs attribute that can be used to indicate when
non-linear brightness scaling is in use. As Custom brightness curves
work by linear interpolation of points the scale is no longer linear.
[How]
Indicate non-linear scaling when custom brightness curves in use and
linear scaling otherwise.
Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Mario Limonciello <superm1@kernel.org> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why&how]
control flag for the wait during pipe update wait for vupdate should
be set if update type is not fast or med to prevent an invalid sleep
operation
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since there are too many variants available for Foxconn T99W696 modem, and
they all share the same configuration, use PCI_ANY_ID as the subsystem
device ID to match each possible SKUs and support all of them.
Since SEV or SNP may already be initialized in the previous kernel,
attempting to initialize them again in the kdump kernel can result
in SNP initialization failures, which in turn lead to IOMMU
initialization failures. Moreover, SNP/SEV guests are not run under a
kdump kernel, so there is no need to initialize SEV or SNP during
kdump boot.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU device table register is locked and exclusive to the previous
kernel. Attempts to copy old device table from the previous kernel
fails in kdump kernel as hardware ignores writes to the locked device
table base address register as per AMD IOMMU spec Section 2.12.2.1.
This causes the IOMMU driver (OS) and the hardware to reference
different memory locations. As a result, the IOMMU hardware cannot
process the command which results in repeated "Completion-Wait loop
timed out" errors and a second kernel panic: "Kernel panic - not
syncing: timer doesn't work through Interrupt-remapped IO-APIC".
Reuse device table instead of copying device table in case of kdump
boot and remove all copying device table code.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU completion wait buffers (CWBs), command buffers and event buffer
registers remain locked and exclusive to the previous kernel. Attempts
to allocate and use new buffers in the kdump kernel fail, as hardware
ignores writes to the locked MMIO registers as per AMD IOMMU spec
Section 2.12.2.1.
This results in repeated "Completion-Wait loop timed out" errors and a
second kernel panic: "Kernel panic - not syncing: timer doesn't work
through Interrupt-remapped IO-APIC"
The list of MMIO registers locked and which ignore writes after failed
SNP shutdown are mentioned in the AMD IOMMU specifications below:
Reuse the pages of the previous kernel for completion wait buffers,
command buffers, event buffers and memremap them during kdump boot
and essentially work with an already enabled IOMMU configuration and
re-using the previous kernel’s data structures.
Reusing of command buffers and event buffers is now done for kdump boot
irrespective of SNP being enabled during kdump.
Re-use of completion wait buffers is only done when SNP is enabled as
the exclusion base register is used for the completion wait buffer
(CWB) address only when SNP is enabled.
Handle the case where the hmm range partially covers a huge page (like
2M), otherwise we can potentially end up doing something nasty like
mapping memory which is outside the range, and maybe not even mapped by
the mm. Fix is based on the xe userptr code, which in a future patch
will directly use gpusvm, so needs alignment here.
v2:
- Add kernel-doc (Matt B)
- s/fls/ilog2/ (Thomas)
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Link: https://lore.kernel.org/r/20250828142430.615826-11-matthew.auld@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After analysis, it appears this is because of the cond_resched()
call from __release_sock().
When current thread is yielding, while still holding the TCP socket lock,
it might regain the cpu after a very long time.
Other peer TLP/RTO is firing (multiple times) and packets are retransmit,
while the initial copy is waiting in the socket backlog or receive queue.
In this patch, I call cond_resched() only once every 16 packets.
Modern TCP stack now spends less time per packet in the backlog,
especially because ACK are no longer sent (commit 133c4c0d3717
"tcp: defer regular ACK while processing socket backlog")
The GuC communication protocol allows GuC to send NO_RESPONSE_RETRY
reply message to indicate that due to some interim condition it can
not handle incoming H2G request and the host shall resend it.
But in some cases, due to errors, this unsatisfied condition might
be final and this could lead to endless retries as it was recently
seen on the CI:
To avoid such dangerous loops allow only limited number of retries
(for now 50) and add some delays (n * 5ms) to slow down the rate of
resending this repeated request.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Reviewed-by: Julia Filipchuk <julia.filipchuk@intel.com> Link: https://lore.kernel.org/r/20250903223330.6408-1-michal.wajdeczko@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the 3.3Vaux supply is present, fetch it at the probe time and keep it
enabled for the entire PCIe controller lifecycle so that the link can enter
L2 state and the devices can signal wakeup using either Beacon or WAKE#
mechanisms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded the subject, description and error message] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20250820022328.2143374-1-hongxing.zhu@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In partitioned systems, the domain ID is unique in the partition and a
package can have multiple partitions.
Some user-space tools, such as turbostat, assume the domain ID is unique
per package. These tools map CPU power domains, which are unique to a
package. However, this approach does not work in partitioned systems.
There is no architectural definition of "partition" to present to user
space.
To support these tools, set the domain_id to be unique per package. For
compute die IDs, uniqueness can be achieved using the platform info
cdie_mask, mirroring the behavior observed in non-partitioned systems.
For IO dies, which lack a direct CPU relationship, any unique logical
ID can be assigned. Here domain IDs for IO dies are configured after all
compute domain IDs. During the probe, keep the index of the next IO
domain ID after the last IO domain ID of the current partition. Since
CPU packages are symmetric, partition information is same for all
packages.
The Intel Speed Select driver has already implemented a similar change
to make the domain ID unique, with compute dies listed first, followed
by I/O dies.
Currently, when adding the 6 GHz Band Capabilities element, the channel
list of the wiphy is checked to determine if 6 GHz is supported for a given
virtual interface. However, in a multi-radio wiphy (e.g., one that has
both lower bands and 6 GHz combined), the wiphy advertises support for
all bands. As a result, the 6 GHz Band Capabilities element is incorrectly
included in mesh beacon and station's association request frames of
interfaces operating in lower bands, without verifying whether the
interface is actually operating in a 6 GHz channel.
Fix this by verifying if the interface operates on 6 GHz channel
before adding the element. Note that this check cannot be placed
directly in ieee80211_put_he_6ghz_cap() as the same function is used to
add probe request elements while initiating scan in which case the
interface may not be operating in any band's channel.
Call the dedicated v4l2_disable_ioctl helper instead of manually
checking whether the current context is an encoder for the selection
api ioctls.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .querystd callback should not program the device with the detected
standard, it should only report the standard to user-space. User-space
may then use .s_std to set the standard, if it wants to use it.
All that is required of .querystd is to setup the auto detection of
standards and report its findings.
While at it add some documentation on why this can't happen while
streaming and improve the error handling using a scoped guard.
projects / thirdparty / kernel / stable.git / log
