The root cause of the problem is located in the OpenWrt specific quilt
patch, which sets the quilt install directory to $STAGING_DIR/../host.
However, on a clean environment (right after running "make clean"),
$STAGING_DIR doesn't exist. The "quilt" executable doesn't find its
different commands, errors out, and creates this message.
We're fixing it by using $STAGING_DIR_HOST rather than $STAGING_DIR,
which is absolute. It will work even if there is no target directory
yet.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47410
Felix Fietkau [Sat, 7 Nov 2015 12:52:07 +0000 (12:52 +0000)]
rules.mk: export STAGING_DIR_HOST to sub-makefiles and shells
Certains host packages (like quilt) need to know the previously used
install location at run-time. They currently use $STAGING_DIR, which
causes issues on cleaned environment, where $STAGING_DIR doesn't exist
yet.
Felix Fietkau [Sat, 7 Nov 2015 12:52:01 +0000 (12:52 +0000)]
mac80211: set mcast-rate for mesh point interfaces
In order to set the multicast rate for mesh point interfaces the "mesh join"
was made explicit and moved to mac80211_setup_vif(), similar to how it is
done for IBSS interfaces.
Previously, the mesh join was made implicit in case authentication (i.e.
$key) was not used when creating the interface in mac80211_prepare_vif(),
while using authentication would create the interface first, then join
later in mac80211_setup_vif() by starting authsae.
Signed-off-by: Nils Schneider <nils@nilsschneider.net>
SVN-Revision: 47408
In case if we're interested in generation of non-binary images
(for example if we want images to be valid .elfs - and that's what we
want for ARC now) we have to instruct Device/Build/initramfs target to
use input file with some extension (in case of ARC it will be
essentially .elf).
Otherwise default binary vmlinux-initramfs (without extension) is used and
resulting images then are binaries instead of elfs.
Now having KERNEL_INITRAMFS_NAME variable it's possible to substitute
default $$(KERNEL_NAME)-initramfs with preferred option like
$$(KERNEL_NAME)-initramfs.elf.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Felix Fietkau <nbd@openwrt.org> Cc: John Crispin <blogic@openwrt.org>
SVN-Revision: 47403
Jonas Gorski [Wed, 4 Nov 2015 11:33:31 +0000 (11:33 +0000)]
ipq806x: fix BOARD_NAME spellings
the board names used by the upgrade check differ from the device names
in case, so always set them. We can't rely on tolower or similar since
different locales might have different rules for lower case letters, so
set them explicitily.
Fixes sysupgrade rejecting *-sysupgrade.tar because of the difference.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de> Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47381
Jonas Gorski [Wed, 4 Nov 2015 11:33:22 +0000 (11:33 +0000)]
brcm63xx: work around boot failures with squashfs on BCM6368
Due to the LWL/LWR SMP issue on BCM6368, booting with squash might fail
if the rootfs is not word aligned. As a quick fix, work around it by
ensuring this condition is always true.
Felix Fietkau [Tue, 3 Nov 2015 11:59:09 +0000 (11:59 +0000)]
lldpd: implement a reload hook
Seems the default one is not working as expected.
The way that reload should work is that the 'start' service
call should return 1 (if lldpd is running) and then a normal
restart would be called.
However, for lldpd a reload would mean just clearing all custom TLVs
(if they're configured) and reloading the configuration.
So, this patch adds a reload hook, which would:
- 'start' lldpd if it's not running (because we return 1 if not running)
- reload configuration if it is running (also previously
clearing custom TLVs if present)
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47367
Felix Fietkau [Mon, 2 Nov 2015 18:26:15 +0000 (18:26 +0000)]
mac80211: fix crash when using mesh (11s) VIF together with another VIF
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Felix Fietkau [Mon, 2 Nov 2015 18:12:54 +0000 (18:12 +0000)]
hostapd: add default value to eapol_version (#20641)
r46861 introduced a new option eapol_version to hostapd, but did not
provide a default value. When the option value is evaluated,
the non-existing value causes errors to the systen log:
"netifd: radio0: sh: out of range"
Add a no-op default value 0 for eapol_version. Only values 1 or 2 are
actually passed on, so 0 will not change the default action in hostapd.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47361
Felix Fietkau [Mon, 2 Nov 2015 18:12:29 +0000 (18:12 +0000)]
include/kernel.mk - better search for ARCH
If "findstring" is used without leading and trailing spaces unexpected matches
may happen. For example consider ARC=arc then "findstring $(ARCH)" will
report a false match with "aarch64".
But "findstring $ARCH " (note trailing space) will correctly skip
matches for both "aarch64" and "aarch64_be".
This patch is built-tested against NetGear WNDR3800.
Felix Fietkau [Mon, 2 Nov 2015 18:12:10 +0000 (18:12 +0000)]
uclibc-ng: bump version from 1.0.6 to 1.0.8
2 new architectures were added in between 1.0.6 and 1.0.8 in uClibc-ng,
these are:
* lm32
* or1k
Even thought both are not yet supported in OpenWRT it's important to
disable them both in default config file otherwise user prompt will
appear during uClibc configuration asking to select desired
architecture.
John Crispin [Mon, 2 Nov 2015 10:18:02 +0000 (10:18 +0000)]
ramips: preinit: use iproute2 instead of vconfig
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips
The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47349
John Crispin [Mon, 2 Nov 2015 10:17:41 +0000 (10:17 +0000)]
ramips: add function to change rt2x00 wifi eeprom mac
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47347
John Crispin [Mon, 2 Nov 2015 10:17:35 +0000 (10:17 +0000)]
ramips: mt7620 add icplus phy driver kernel config symbol
Add missing icplus phy driver kernel config symbol to mt7620 subtarget.
This is needed since some mt7620 devices have icplus ip1001 ethernet transceiver
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47346
John Crispin [Mon, 2 Nov 2015 10:17:26 +0000 (10:17 +0000)]
ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.
Signed-off-by: Alberto Mattea <alberto@mattea.info>
SVN-Revision: 47345
John Crispin [Mon, 2 Nov 2015 10:17:15 +0000 (10:17 +0000)]
ar71xx: Add support for wdr7500v3
The device is similar to Archer C7 v2, but with 8M of flash, and 6 external
antennas. Reason for breaking the naming pattern is that sticker on the back
mentions "WDR7500" and has no mention of "Archer".
John Crispin [Mon, 2 Nov 2015 10:16:28 +0000 (10:16 +0000)]
package/devel/perf: fix build for kernel 4.1
This fix contains 2 parts:
- kernel 4.1: backport upstream patch "perf build: Do not fail on missing Build file"
- add NO_LZMA=1 to perf MAKE_FLAGS to disable LZMA support
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47338
Felix Fietkau [Sat, 31 Oct 2015 09:30:57 +0000 (09:30 +0000)]
malta: make eth0 the wan interface by default
Many packages for OpenWrt currently assume that lan is the "internal"
side of the network map, e.g. if installed, dnsmasq will hand out DHCP
leases on lan, firewall will allow forwarding on lan.
While at it, also configure a lan interface if eth1 exists.
Felix Fietkau [Sat, 31 Oct 2015 09:30:37 +0000 (09:30 +0000)]
malta: use as a default type device
There is currently no relevant definition for developerboard device type
in include/target.mk, thus packages like iptables, firewall, dnsmasq
etc. are missing in the default images, rendering it almost useless
for regular testing or normal use.
With this change, currently a default set of packages for "router" will
be installed to malta firmware images.
Felix Fietkau [Sat, 31 Oct 2015 09:30:14 +0000 (09:30 +0000)]
malta: set CPU_TYPE:=24kc.
There are instructions (e.g. wsbh) only available in MIPS32R2 which is
the isa level used by many MIPS targets in OpenWrt. As we use the malta
target mostly for development and testing purposes, setting the CPU_TYPE
to 24Kc will make the emulation more real.
The following is output from qemu-system-mipsel 2.3.0
root@OpenWrt:/# cat /proc/cpuinfo | grep 'cpu model\|isa'
cpu model : MIPS 24Kc V0.0 FPU V0.0
isa : mips1 mips2 mips32r1 mips32r2
projects / thirdparty / openwrt.git / log
