Add documentation for the vsock per-namespace sysctls (`ns_mode` and
`child_ns_mode`) to Documentation/admin-guide/sysctl/net.rst.
These sysctls were introduced by commit eafb64f40ca4 ("vsock: add
netns to vsock core").
Document the two namespace modes (`global` and `local`), the
inheritance behavior of `child_ns_mode`, and the restriction preventing
local namespaces from setting `child_ns_mode` to `global`.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Link: https://patch.msgid.link/20260216163147.236844-1-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Fri, 13 Feb 2026 14:25:57 +0000 (14:25 +0000)]
macvlan: observe an RCU grace period in macvlan_common_newlink() error path
valis reported that a race condition still happens after my prior patch.
macvlan_common_newlink() might have made @dev visible before
detecting an error, and its caller will directly call free_netdev(dev).
We must respect an RCU period, either in macvlan or the core networking
stack.
After adding a temporary mdelay(1000) in macvlan_forward_source_one()
to open the race window, valis repro was:
ip link add p1 type veth peer p2
ip link set address 00:00:00:00:00:20 dev p1
ip link set up dev p1
ip link set up dev p2
ip link add mv0 link p2 type macvlan mode source
(ip link add invalid% link p2 type macvlan mode source macaddr add
00:00:00:00:00:20 &) ; sleep 0.5 ; ping -c1 -I p1 1.2.3.4
PING 1.2.3.4 (1.2.3.4): 56 data bytes
RTNETLINK answers: Invalid argument
BUG: KASAN: slab-use-after-free in macvlan_forward_source
(drivers/net/macvlan.c:408 drivers/net/macvlan.c:444)
Read of size 8 at addr ffff888016bb89c0 by task e/175
Jakub Kicinski [Sat, 14 Feb 2026 03:51:59 +0000 (19:51 -0800)]
selftests: tc_actions: don't dump 2MB of \0 to stdout
Since we started running selftests in NIPA we have been seeing
tc_actions.sh generate a soft lockup warning on ~20% of the runs.
On the pre-netdev foundation setup it was actually a missed irq
splat from the console. Now it's either that or a lockup.
I initially suspected a socket locking issue since the test
is exercising local loopback with act_mirred.
After hours of staring at this I noticed in strace that ncat
when -o $file is specified _both_ saves the output to the file
and still prints it to stdout. Because the file being sent
is constructed with:
the data printed is all \0. Most terminals don't display nul
characters (and neither does vng output capture save them).
But QEMU's serial console still has to poke them thru which
is very slow and causes the lockup (if the file is >600kB).
Replace the '-o $file' with '> $file'. This speeds the test up
from 2m20s to 18s on debug kernels, and prevents the warnings.
ipv6: addrconf: reduce default temp_valid_lft to 2 days
This is a recommendation from RFC 8981 and it was intended to be changed
by commit 969c54646af0 ("ipv6: Implement draft-ietf-6man-rfc4941bis")
but it only changed the sysctl documentation.
Eric Dumazet [Mon, 16 Feb 2026 10:01:49 +0000 (10:01 +0000)]
ping: annotate data-races in ping_lookup()
isk->inet_num, isk->inet_rcv_saddr and sk->sk_bound_dev_if
are read locklessly in ping_lookup().
Add READ_ONCE()/WRITE_ONCE() annotations.
The race on isk->inet_rcv_saddr is probably coming from IPv6 support,
but does not deserve a specific backport.
Fixes: dbca1596bbb0 ("ping: convert to RCU lookups, get rid of rwlock") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com> Link: https://patch.msgid.link/20260216100149.3319315-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ivan Vecera [Mon, 16 Feb 2026 19:40:07 +0000 (20:40 +0100)]
dpll: zl3073x: Fix ref frequency setting
The frequency for an input reference is computed as:
frequency = freq_base * freq_mult * freq_ratio_m / freq_ratio_n
Before commit 5bc02b190a3fb ("dpll: zl3073x: Cache all reference
properties in zl3073x_ref"), zl3073x_dpll_input_pin_frequency_set()
explicitly wrote 1 to both the REF_RATIO_M and REF_RATIO_N hardware
registers whenever a new frequency was set. This ensured the FEC ratio
was always reset to 1:1 alongside the new base/multiplier values.
The refactoring in that commit introduced zl3073x_ref_freq_set() to
update the cached ref state, but this helper only sets freq_base and
freq_mult without resetting freq_ratio_m and freq_ratio_n to 1. Because
zl3073x_ref_state_set() uses a compare-and-write strategy, unchanged
ratio fields are never written to the hardware. If the device previously
had non-unity FEC ratio values, they remain in effect after a frequency
change, resulting in an incorrect computed frequency.
Explicitly set freq_ratio_m and freq_ratio_n to 1 in zl3073x_ref_freq_set()
to restore the original behavior.
Fixes: 5bc02b190a3fb ("dpll: zl3073x: Cache all reference properties in zl3073x_ref") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20260216194007.680416-1-ivecera@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 16 Feb 2026 19:36:53 +0000 (19:36 +0000)]
net: do not delay zero-copy skbs in skb_attempt_defer_free()
After the blamed commit, TCP tx zero copy notifications could be
arbitrarily delayed and cause regressions in applications waiting
for them.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: e20dfbad8aab ("net: fix napi_consume_skb() with alien skbs") Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20260216193653.627617-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Mon, 16 Feb 2026 10:54:54 +0000 (11:54 +0100)]
net: psp: select CONFIG_SKB_EXTENSIONS
psp now uses skb extensions, failing to build when that is disabled:
In file included from include/net/psp.h:7,
from net/psp/psp_sock.c:9:
include/net/psp/functions.h: In function '__psp_skb_coalesce_diff':
include/net/psp/functions.h:60:13: error: implicit declaration of function 'skb_ext_find'; did you mean 'skb_ext_copy'? [-Wimplicit-function-declaration]
60 | a = skb_ext_find(one, SKB_EXT_PSP);
| ^~~~~~~~~~~~
| skb_ext_copy
include/net/psp/functions.h:60:31: error: 'SKB_EXT_PSP' undeclared (first use in this function)
60 | a = skb_ext_find(one, SKB_EXT_PSP);
| ^~~~~~~~~~~
include/net/psp/functions.h:60:31: note: each undeclared identifier is reported only once for each function it appears in
include/net/psp/functions.h: In function '__psp_sk_rx_policy_check':
include/net/psp/functions.h:94:53: error: 'SKB_EXT_PSP' undeclared (first use in this function)
94 | struct psp_skb_ext *pse = skb_ext_find(skb, SKB_EXT_PSP);
| ^~~~~~~~~~~
net/psp/psp_sock.c: In function 'psp_sock_recv_queue_check':
net/psp/psp_sock.c:164:41: error: 'SKB_EXT_PSP' undeclared (first use in this function)
164 | pse = skb_ext_find(skb, SKB_EXT_PSP);
| ^~~~~~~~~~~
Select the Kconfig symbol as we do from its other users.
Fixes: 6b46ca260e22 ("net: psp: add socket security association code") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com> Link: https://patch.msgid.link/20260216105500.2382181-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
selftests: forwarding: fix br_netfilter related test failures
This patch series fixes kselftests that fail when the br_nefilter
module is loaded. The failures occur because the tests generate
packets that are either modified or encapsulated, but their IP
headers are not fully correct for sanity checks performed by
be_netfilter.
Signed-off-by: Aleksei Oladko <aleksey.oladko@virtuozzo.com>
====================
Aleksei Oladko [Fri, 13 Feb 2026 13:19:07 +0000 (13:19 +0000)]
selftests: forwarding: fix pedit tests failure with br_netfilter enabled
The tests use the tc pedit action to modify the IPv4 source address
("pedit ex munge ip src set"), but the IP header checksum is not
recalculated after the modification. As a result, the modified packet
fails sanity checks in br_netfilter after bridging and is dropped,
which causes the test to fail.
Fix this by ensuring net.bridge.bridge-nf-call-iptables is set to 0
during the test execution. This prevents the bridge from passing
L2 traffic to netfilter, bypassing the checksum validation that
causes the test failure.
Fixes: 92ad3828944e ("selftests: forwarding: Add a test for pedit munge SIP and DIP") Fixes: 226657ba2389 ("selftests: forwarding: Add a forwarding test for pedit munge dsfield") Signed-off-by: Aleksei Oladko <aleksey.oladko@virtuozzo.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20260213131907.43351-4-aleksey.oladko@virtuozzo.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Aleksei Oladko [Fri, 13 Feb 2026 13:19:06 +0000 (13:19 +0000)]
selftests: forwarding: vxlan_bridge_1d_ipv6: fix test failure with br_netfilter enabled
The test generates VXLAN traffic using mausezahn, where the encapsulated
inner IPv6 packet has an incorrect payload length set in the IPv6 header.
After VXLAN decapsulation, such packets do not pass sanity checks in
br_netfilter and are dropped, which causes the test to fail.
Fix this by setting the correct IPv6 payload length for the encapsulated
packet generated by mausezahn, so that the packet is accepted
by br_netfilter.
Aleksei Oladko [Fri, 13 Feb 2026 13:19:05 +0000 (13:19 +0000)]
selftests: forwarding: vxlan_bridge_1d: fix test failure with br_netfilter enabled
The test generates VXLAN traffic using mausezahn, where the encapsulated
inner IPv4 packet contains a zero IP header checksum. After VXLAN
decapsulation, such packets do not pass sanity checks in br_netfilter
and are dropped, which causes the test to fail.
Fix this by calculating and setting a valid IPv4 header checksum for the
encapsulated packet generated by mausezahn, so that the packet is accepted
by br_netfilter. Fixed by using the payload_template_calc_checksum() /
payload_template_expand_checksum() helpers that are only available
in v6.3 and newer kernels.
Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test") Signed-off-by: Aleksei Oladko <aleksey.oladko@virtuozzo.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20260213131907.43351-2-aleksey.oladko@virtuozzo.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In that configuration, the netconsole driver is useless anyway, so
avoid this with an added dependency that prevents CONFIG_NETCONSOLE
to be enabled without CONFIG_PRINTK.
Fixes: 60325c27d3cf ("printk: Add execution context (task name/CPU) to printk_info") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20260213074431.1729627-1-arnd@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The first patch fixes a warning in the mdb_n_entries code which was
reported by syzbot, the second patch adds tests for different ways
which used to trigger said warning. For more information please check
the individual commit messages.
====================
selftests: forwarding: bridge_mdb_max: add tests for mdb_n_entries warning
Recently we were able to trigger a warning in the mdb_n_entries counting
code. Add tests that exercise different ways which used to trigger that
warning.
net: bridge: mcast: always update mdb_n_entries for vlan contexts
syzbot triggered a warning[1] about the number of mdb entries in a context.
It turned out that there are multiple ways to trigger that warning today
(some got added during the years), the root cause of the problem is that
the increase is done conditionally, and over the years these different
conditions increased so there were new ways to trigger the warning, that is
to do a decrease which wasn't paired with a previous increase.
For example one way to trigger it is with flush:
$ ip l add br0 up type bridge vlan_filtering 1 mcast_snooping 1
$ ip l add dumdum up master br0 type dummy
$ bridge mdb add dev br0 port dumdum grp 239.0.0.1 permanent vid 1
$ ip link set dev br0 down
$ ip link set dev br0 type bridge mcast_vlan_snooping 1
^^^^ this will enable snooping, but will not update mdb_n_entries
because in __br_multicast_enable_port_ctx() we check !netif_running
$ bridge mdb flush dev br0
^^^ this will trigger the warning because it will delete the pg which
we added above, which will try to decrease mdb_n_entries
Fix the problem by removing the conditional increase and always keep the
count up-to-date while the vlan exists. In order to do that we have to
first initialize it on port-vlan context creation, and then always increase
or decrease the value regardless of mcast options. To keep the current
behaviour we have to enforce the mdb limit only if the context is port's or
if the port-vlan's mcast snooping is enabled.
net: arcnet: com20020-pci: fix support for 2.5Mbit cards
Commit 8c14f9c70327 ("ARCNET: add com20020 PCI IDs with metadata")
converted the com20020-pci driver to use a card info structure instead
of a single flag mask in driver_data. However, it failed to take into
account that in the original code, driver_data of 0 indicates a card
with no special flags, not a card that should not have any card info
structure. This introduced a null pointer dereference when cards with
no flags were probed.
Commit bd6f1fd5d33d ("net: arcnet: com20020: Fix null-ptr-deref in
com20020pci_probe()") then papered over this issue by rejecting cards
with no driver_data instead of resolving the problem at its source.
Fix the original issue by introducing a new card info structure for
2.5Mbit cards that does not set any flags and using it if no
driver_data is present.
Fixes: 8c14f9c70327 ("ARCNET: add com20020 PCI IDs with metadata") Fixes: bd6f1fd5d33d ("net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()") Cc: stable@vger.kernel.org Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com> Link: https://patch.msgid.link/20260213045510.32368-1-enelsonmoore@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net/rds: rds_sendmsg should not discard payload_len
Commit 3db6e0d172c9 ("rds: use RCU to synchronize work-enqueue with
connection teardown") modifies rds_sendmsg to avoid enqueueing work
while a tear down is in progress. However, it also changed the return
value of rds_sendmsg to that of rds_send_xmit instead of the
payload_len. This means the user may incorrectly receive errno values
when it should have simply received a payload of 0 while the peer
attempts a reconnections. So this patch corrects the teardown handling
code to only use the out error path in that case, thus restoring the
original payload_len return value.
Fixes: 3db6e0d172c9 ("rds: use RCU to synchronize work-enqueue with connection teardown") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Allison Henderson <achender@kernel.org> Link: https://patch.msgid.link/20260213035409.1963391-1-achender@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ziyi Guo [Thu, 12 Feb 2026 22:40:40 +0000 (22:40 +0000)]
xen-netback: reject zero-queue configuration from guest
A malicious or buggy Xen guest can write "0" to the xenbus key
"multi-queue-num-queues". The connect() function in the backend only
validates the upper bound (requested_num_queues > xenvif_max_queues)
but not zero, allowing requested_num_queues=0 to reach
vzalloc(array_size(0, sizeof(struct xenvif_queue))), which triggers
WARN_ON_ONCE(!size) in __vmalloc_node_range().
On systems with panic_on_warn=1, this allows a guest-to-host denial
of service.
The Xen network interface specification requires
the queue count to be "greater than zero".
Add a zero check to match the validation already present
in xen-blkback, which has included this
guard since its multi-queue support was added.
Fixes: 8d3d53b3e433 ("xen-netback: Add support for multiple queues") Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://patch.msgid.link/20260212224040.86674-1-n7l8m4@u.northwestern.edu Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ziyi Guo [Thu, 12 Feb 2026 21:41:54 +0000 (21:41 +0000)]
net: usb: catc: enable basic endpoint checking
catc_probe() fills three URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX
- usb_rcvintpipe(usbdev, 2) for interrupt status
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a catc_usb_ep enum for endpoint numbers, replacing magic constants
throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints()
calls after usb_set_interface() to verify endpoint types before use,
rejecting devices with mismatched descriptors at probe time.
Similar to
- commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking")
which fixed the issue in rtl8150.
ovpn: tcp - don't deref NULL sk_socket member after tcp_close()
When deleting a peer in case of keepalive expiration, the peer is
removed from the OpenVPN hashtable and is temporary inserted in a
"release list" for further processing.
This happens in:
ovpn_peer_keepalive_work()
unlock_ovpn(release_list)
This processing includes detaching from the socket being used to
talk to this peer, by restoring its original proto and socket
ops/callbacks.
In case of TCP it may happen that, while the peer is sitting in
the release list, userspace decides to close the socket.
This will result in a concurrent execution of:
The last function call will set sk->sk_socket to NULL.
When the releasing routine is resumed, ovpn_tcp_socket_detach()
will attempt to dereference sk->sk_socket to restore its original
ops member. This operation will crash due to sk->sk_socket being NULL.
Fix this race condition by testing-and-accessing
sk->sk_socket atomically under sk->sk_callback_lock.
Paolo Abeni [Tue, 17 Feb 2026 10:15:54 +0000 (11:15 +0100)]
Merge tag 'ovpn-net-20260212' of https://github.com/OpenVPN/ovpn-net-next
Antonio Quartulli says:
====================
This batch includes the following fixes:
* set sk_user_data before installing callbacks, to avoid dropping early
packets
* fix use-after-free in ovpn_net_xmit when accessing shared skbs that
got released
* fix TX bytes stats by adding-up every positively processed GSO
segment
====================
====================
eth: fbnic: fix and improve header/data split configuration
This series fixes TCP HDS configuration in the fbnic driver and adds a
devmem selftest for the intended behavior.
The issues fixed include setting the correct CSR for EN_HDR_SPLIT,
adjusting the hds threshold clamp to avoid long headers overflowing into
the payload page, and configuring the device to use L4/L3/L2 header
boundaries when present by programming the DMA hint bit unconditionally
for all steering rule types.
Prior to these fixes, small payloads fail devmem.check_rx_hds().
TAP version 13
1..4
ok 1 devmem.check_rx
ok 2 devmem.check_tx
ok 3 devmem.check_tx_chunks
ok 4 devmem.check_rx_hds
To: Alexander Duyck <alexanderduyck@fb.com>
To: Jakub Kicinski <kuba@kernel.org>
To: kernel-team@meta.com
To: Andrew Lunn <andrew+netdev@lunn.ch>
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Paolo Abeni <pabeni@redhat.com>
To: Mohsin Bashir <mohsin.bashr@gmail.com>
To: Shuah Khan <shuah@kernel.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-kselftest@vger.kernel.org Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
====================
Bobby Eshleman [Thu, 12 Feb 2026 01:00:44 +0000 (17:00 -0800)]
selftests: drv-net: add HDS payload sweep test for devmem TCP
Add check_rx_hds test that verifies header/data split works across
payload sizes. The test sweeps payload sizes from 1 byte to 8KB, if any
data propagates up to userspace as SCM_DEVMEM_LINEAR, then the test
fails. This shows that regardless of payload size, ncdevmem's
configuration of hds-thresh to 0 is respected.
Add -L (--fail-on-linear) flag to ncdevmem that causes the receiver to
fail if any SCM_DEVMEM_LINEAR cmsg is received.
Use socat option for fixed block sizing and tcp nodelay to disable
nagle's algo to avoid buffering.
Bobby Eshleman [Thu, 12 Feb 2026 01:00:43 +0000 (17:00 -0800)]
eth: fbnic: set DMA_HINT_L4 for all flows
fbnic always advertises ETHTOOL_TCP_DATA_SPLIT_ENABLED via ethtool
.get_ringparam. To enable proper splitting for all flow types, even for
IP/Ethernet flows, this patch sets DMA_HINT_L4 unconditionally for all
RSS and NFC flow steering rules. According to the spec, L4 falls back to
L3 if no valid L4 is found, and L3 falls back to L2 if no L3 is found.
This makes sure that the correct header boundary is used regardless of
traffic type. This is important for zero-copy use cases where we must
ensure that all ZC packets are split correctly.
Bobby Eshleman [Thu, 12 Feb 2026 01:00:42 +0000 (17:00 -0800)]
eth: fbnic: increase FBNIC_HDR_BYTES_MIN from 128 to 256 bytes
Increase FBNIC_HDR_BYTES_MIN from 128 to 256 bytes. The previous minimum
was too small to guarantee that very long L2+L3+L4 headers always fit
within the header buffer. When EN_HDR_SPLIT is disabled and a packet
exceeds MAX_HEADER_BYTES, splitting occurs at that byte offset instead
of the header boundary, resulting in some of the header landing in the
payload page. The increased minimum ensures headers always fit with the
MAX_HEADER_BYTES cut off and land in the header page.
Bobby Eshleman [Thu, 12 Feb 2026 01:00:41 +0000 (17:00 -0800)]
eth: fbnic: set FBNIC_QUEUE_RDE_CTL0_EN_HDR_SPLIT on RDE_CTL0
Fix EN_HDR_SPLIT configuration by writing the field to RDE_CTL0 instead
of RDE_CTL1.
Because drop mode configuration and header splitting enablement both use
RDE_CTL0, we consolidate these configurations into the single function
fbnic_config_drop_mode.
Chengfeng Ye [Wed, 11 Feb 2026 19:13:29 +0000 (19:13 +0000)]
fbnic: close fw_log race between users and teardown
Fixes a theoretical race on fw_log between the teardown path and fw_log
write functions.
fw_log is written inside fbnic_fw_log_write() and can be reached from
the mailbox handler fbnic_fw_msix_intr(), but fw_log is freed before
IRQ/MBX teardown during cleanup, resulting in a potential data race of
dereferencing a freed/null variable.
Possible Interleaving Scenario:
CPU0: fbnic_fw_msix_intr() // Entry
fbnic_fw_log_write()
if (fbnic_fw_log_ready()) // true
... preempt ...
CPU1: fbnic_remove() // Entry
fbnic_fw_log_free()
vfree(log->data_start);
log->data_start = NULL;
CPU0: continues, walks log->entries or writes to log->data_start
The initialization also has an incorrect order problem, as the fw_log
is currently allocated after MBX setup during initialization.
Fix the problems by adjusting the synchronization order to put
initialization in place before the mailbox is enabled, and not cleared
until after the mailbox has been disabled.
====================
vsock: fix child netns mode initialization and restriction
This series fixes two issues in the vsock network namespace support
recently introduced by commit eafb64f40ca4 ("vsock: add netns to vsock
core").
Patch 1 fixes `child_ns_mode` being always hardcoded to "global" for new
namespaces, breaking propagation of the "local" mode through nested
namespaces.
Patch 2 prevents a "local" namespace from switching `child_ns_mode` to
"global", which would allow nested namespaces to escape vsock isolation
and access global CIDs.
====================
vsock: prevent child netns mode switch from local to global
A "local" namespace can change its `child_ns_mode` sysctl to "global",
allowing nested namespaces to access global CIDs. This can be exploited
by an unprivileged user who gained CAP_NET_ADMIN through a user
namespace.
Prevent this by rejecting writes that attempt to set `child_ns_mode` to
"global" when the current namespace's mode is "local".
Fixes: eafb64f40ca4 ("vsock: add netns to vsock core") Cc: bobbyeshleman@meta.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com> Link: https://patch.msgid.link/20260212205916.97533-3-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a new network namespace is created, vsock_net_init() correctly
initializes the namespace's mode by reading the parent's `child_ns_mode`
via vsock_net_child_mode(). However, the `child_ns_mode` of the new
namespace was always hardcoded to VSOCK_NET_MODE_GLOBAL, regardless of
its own mode.
This means that if a parent namespace has `child_ns_mode` set to "local",
the child namespace correctly gets mode "local", but its `child_ns_mode`
is reset to "global". As a result, further nested namespaces will
incorrectly get mode "global" instead of inheriting "local", breaking
the expected propagation of the mode through nested namespaces.
Fix this by initializing `child_ns_mode` to the namespace's own mode,
so the setting propagates correctly through all levels of nesting.
Fixes: eafb64f40ca4 ("vsock: add netns to vsock core") Cc: bobbyeshleman@meta.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com> Link: https://patch.msgid.link/20260212205916.97533-2-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Machon [Thu, 12 Feb 2026 11:02:30 +0000 (12:02 +0100)]
net: sparx5/lan969x: fix PTP clock max_adj value
The max_adj field in ptp_clock_info tells userspace how much the PHC
clock frequency can be adjusted. ptp4l reads this and will never request
a correction larger than max_adj.
On both sparx5 and lan969x the clock offset may never converge because
the servo needs a frequency correction larger than the current max_adj
of 200000 (200 ppm) allows. The servo rails at the max and the offset
stays in the tens of microseconds.
The hardware has no inherent max adjustment limit; frequency correction
is done by writing a 64-bit clock period increment to CLK_PER_CFG, and
the register has plenty of range. The 200000 value was just an overly
conservative software limit. The max_adj is shared between sparx5 and
lan969x, and the increased value is safe for both.
Fix this by increasing max_adj to 10000000 (10000 ppm), giving the
servo sufficient headroom.
ipv6: Fix out-of-bound access in fib6_add_rt2node().
syzbot reported out-of-bound read in fib6_add_rt2node(). [0]
When IPv6 route is created with RTA_NH_ID, struct fib6_info
does not have the trailing struct fib6_nh.
The cited commit started to check !iter->fib6_nh->fib_nh_gw_family
to ensure that rt6_qualify_for_ecmp() will return false for iter.
If iter->nh is not NULL, rt6_qualify_for_ecmp() returns false anyway.
Let's check iter->nh before reading iter->fib6_nh and avoid OOB read.
[0]:
BUG: KASAN: slab-out-of-bounds in fib6_add_rt2node+0x349c/0x3500 net/ipv6/ip6_fib.c:1142
Read of size 1 at addr ffff8880384ba6de by task syz.0.18/5500
Qanux [Wed, 11 Feb 2026 04:04:12 +0000 (12:04 +0800)]
ipv6: ioam: fix heap buffer overflow in __ioam6_fill_trace_data()
On the receive path, __ioam6_fill_trace_data() uses trace->nodelen
to decide how much data to write for each node. It trusts this field
as-is from the incoming packet, with no consistency check against
trace->type (the 24-bit field that tells which data items are
present). A crafted packet can set nodelen=0 while setting type bits
0-21, causing the function to write ~100 bytes past the allocated
region (into skb_shared_info), which corrupts adjacent heap memory
and leads to a kernel panic.
Add a shared helper ioam6_trace_compute_nodelen() in ioam6.c to
derive the expected nodelen from the type field, and use it:
- in ioam6_iptunnel.c (send path, existing validation) to replace
the open-coded computation;
- in exthdrs.c (receive path, ipv6_hop_ioam) to drop packets whose
nodelen is inconsistent with the type field, before any data is
written.
Per RFC 9197, bits 12-21 are each short (4-octet) fields, so they
are included in IOAM6_MASK_SHORT_FIELDS (changed from 0xff100000 to
0xff1ffc00).
Fixes: 9ee11f0fff20 ("ipv6: ioam: Data plane support for Pre-allocated Trace") Cc: stable@vger.kernel.org Signed-off-by: Junxi Qian <qjx1298677004@gmail.com> Reviewed-by: Justin Iurman <justin.iurman@gmail.com> Link: https://patch.msgid.link/20260211040412.86195-1-qjx1298677004@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pin-yen Lin [Tue, 10 Feb 2026 00:59:36 +0000 (16:59 -0800)]
selftests: netconsole: Increase port listening timeout
wait_for_port() can wait up to 2 seconds with the sleep and the polling
in wait_local_port_listen() combined. So, in netcons_basic.sh, the socat
process could die before the test writes to the netconsole.
Increase the timeout to 3 seconds to make netcons_basic.sh pass
consistently.
Fixes: 3dc6c76391cb ("selftests: net: Add IPv6 support to netconsole basic tests") Signed-off-by: Pin-yen Lin <treapking@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20260210005939.3230550-1-treapking@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net: mscc: ocelot: fix missing lock in ocelot_port_xmit()
ocelot_port_xmit() calls ocelot_can_inject() and
ocelot_port_inject_frame() without holding the injection group lock.
Both functions contain lockdep_assert_held() for the injection lock,
and the correct caller felix_port_deferred_xmit() properly acquires
the lock using ocelot_lock_inj_grp() before calling these functions.
this v3 splits the fix into a 3-patch series to separate
refactoring from the behavioral change:
1/3: Extract the PTP timestamp handling into an ocelot_xmit_timestamp()
helper so the logic isn't duplicated when the function is split.
2/3: Split ocelot_port_xmit() into ocelot_port_xmit_fdma() and
ocelot_port_xmit_inj(), keeping the FDMA and register injection
code paths fully separate.
3/3: Add ocelot_lock_inj_grp()/ocelot_unlock_inj_grp() in
ocelot_port_xmit_inj() to fix the missing lock protection.
Patches 1-2 are pure refactors with no behavioral change.
Patch 3 is the actual bug fix.
====================
Ziyi Guo [Sun, 8 Feb 2026 22:56:02 +0000 (22:56 +0000)]
net: mscc: ocelot: add missing lock protection in ocelot_port_xmit_inj()
ocelot_port_xmit_inj() calls ocelot_can_inject() and
ocelot_port_inject_frame() without holding the injection group lock.
Both functions contain lockdep_assert_held() for the injection lock,
and the correct caller felix_port_deferred_xmit() properly acquires
the lock using ocelot_lock_inj_grp() before calling these functions.
Add ocelot_lock_inj_grp()/ocelot_unlock_inj_grp() around the register
injection path to fix the missing lock protection. The FDMA path is not
affected as it uses its own locking mechanism.
Fixes: c5e12ac3beb0 ("net: mscc: ocelot: serialize access to the injection/extraction groups") Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20260208225602.1339325-4-n7l8m4@u.northwestern.edu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyi Guo [Sun, 8 Feb 2026 22:56:01 +0000 (22:56 +0000)]
net: mscc: ocelot: split xmit into FDMA and register injection paths
Split ocelot_port_xmit() into two separate functions:
- ocelot_port_xmit_fdma(): handles the FDMA injection path
- ocelot_port_xmit_inj(): handles the register-based injection path
The top-level ocelot_port_xmit() now dispatches to the appropriate
function based on the ocelot_fdma_enabled static key.
This is a pure refactor with no behavioral change. Separating the two
code paths makes each one simpler and prepares for adding proper locking
to the register injection path without affecting the FDMA path.
Extract the PTP timestamp handling logic from ocelot_port_xmit() into a
separate ocelot_xmit_timestamp() helper function. This is a pure
refactor with no behavioral change.
The helper returns false if the skb was consumed (freed) due to a
timestamp request failure, and true if the caller should continue with
frame injection. The rew_op value is returned via pointer.
This prepares for splitting ocelot_port_xmit() into separate FDMA and
register injection paths in a subsequent patch.
Daniel Machon [Tue, 10 Feb 2026 13:44:01 +0000 (14:44 +0100)]
net: sparx5/lan969x: fix DWRR cost max to match hardware register width
DWRR (Deficit Weighted Round Robin) scheduling distributes bandwidth
across traffic classes based on per-queue cost values, where lower cost
means higher bandwidth share.
The SPX5_DWRR_COST_MAX constant is 63 (6 bits) but the hardware
register field HSCH_DWRR_ENTRY_DWRR_COST is GENMASK(24, 20), only
5 bits wide (max 31). This causes sparx5_weight_to_hw_cost() to
compute cost values that silently overflow via FIELD_PREP, resulting
in incorrect scheduling weights.
Set SPX5_DWRR_COST_MAX to 31 to match the hardware register width.
Duoming Zhou [Tue, 10 Feb 2026 09:45:37 +0000 (17:45 +0800)]
atm: fore200e: fix use-after-free in tasklets during device removal
When the PCA-200E or SBA-200E adapter is being detached, the fore200e
is deallocated. However, the tx_tasklet or rx_tasklet may still be running
or pending, leading to use-after-free bug when the already freed fore200e
is accessed again in fore200e_tx_tasklet() or fore200e_rx_tasklet().
One of the race conditions can occur as follows:
CPU 0 (cleanup) | CPU 1 (tasklet)
fore200e_pca_remove_one() | fore200e_interrupt()
fore200e_shutdown() | tasklet_schedule()
kfree(fore200e) | fore200e_tx_tasklet()
| fore200e-> // UAF
Fix this by ensuring tx_tasklet or rx_tasklet is properly canceled before
the fore200e is released. Add tasklet_kill() in fore200e_shutdown() to
synchronize with any pending or running tasklets. Moreover, since
fore200e_reset() could prevent further interrupts or data transfers,
the tasklet_kill() should be placed after fore200e_reset() to prevent
the tasklet from being rescheduled in fore200e_interrupt(). Finally,
it only needs to do tasklet_kill() when the fore200e state is greater
than or equal to FORE200E_STATE_IRQ, since tasklets are uninitialized
in earlier states. In a word, the tasklet_kill() should be placed in
the FORE200E_STATE_IRQ branch within the switch...case structure.
Jie Zhang [Mon, 9 Feb 2026 22:50:32 +0000 (17:50 -0500)]
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
net: intel: fix PCI device ID conflict between i40e and ipw2200
The ID 8086:104f is matched by both i40e and ipw2200. The same device
ID should not be in more than one driver, because in that case, which
driver is used is unpredictable. Fix this by taking advantage of the
fact that i40e devices use PCI_CLASS_NETWORK_ETHERNET and ipw2200
devices use PCI_CLASS_NETWORK_OTHER to differentiate the devices.
Fixes: 2e45d3f4677a ("i40e: Add support for X710 B/P & SFP+ cards") Cc: stable@vger.kernel.org Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Link: https://patch.msgid.link/20260210021235.16315-1-enelsonmoore@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Tue, 10 Feb 2026 09:31:10 +0000 (11:31 +0200)]
selftests: drv-net: limit RPS test CPUs to supported range
The _get_unused_cpus() function can return CPU numbers >= 16, which
exceeds RPS_MAX_CPUS in toeplitz.c. When this happens, the test fails
with a cryptic message:
# Exception| Traceback (most recent call last):
# Exception| File "/tmp/cur/linux/tools/testing/selftests/net/lib/py/ksft.py", line 319, in ksft_run
# Exception| func(*args)
# Exception| File "/tmp/cur/linux/tools/testing/selftests/drivers/net/hw/toeplitz.py", line 189, in test
# Exception| with bkg(" ".join(rx_cmd), ksft_ready=True, exit_wait=True) as rx_proc:
# Exception| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
# Exception| File "/tmp/cur/linux/tools/testing/selftests/net/lib/py/utils.py", line 124, in __init__
# Exception| super().__init__(comm, background=True,
# Exception| File "/tmp/cur/linux/tools/testing/selftests/net/lib/py/utils.py", line 77, in __init__
# Exception| raise Exception("Did not receive ready message")
# Exception| Exception: Did not receive ready message
Rename _get_unused_cpus() to _get_unused_rps_cpus() and cap the CPU
search range to RPS_MAX_CPUS.
Yue Haibing [Wed, 11 Feb 2026 02:21:46 +0000 (10:21 +0800)]
selftests: net: lib: Fix jq parsing error
The testcase failed as below:
$./vlan_bridge_binding.sh
...
+ adf_ip_link_set_up d1
+ local name=d1
+ shift
+ ip_link_is_up d1
+ ip_link_has_flag d1 UP
+ local name=d1
+ shift
+ local flag=UP
+ shift
++ ip -j link show d1
++ jq --arg flag UP 'any(.[].flags.[]; . == $flag)'
jq: error: syntax error, unexpected '[', expecting FORMAT or QQSTRING_START
(Unix shell quoting issues?) at <top-level>, line 1:
any(.[].flags.[]; . == $flag)
jq: 1 compile error
Remove the extra dot (.) after flags array to fix this.
Ido Schimmel [Mon, 9 Feb 2026 13:53:53 +0000 (14:53 +0100)]
selftests: mlxsw: tc_restrictions: Fix test failure with new iproute2
As explained in [1], iproute2 started rejecting tc-police burst sizes
that result in an overflow. This can happen when the burst size is high
enough and the rate is low enough.
A couple of test cases specify such configurations, resulting in
iproute2 errors and test failure.
Fix by reducing the burst size so that the test will pass with both new
and old iproute2 versions.
Jeremy Kerr [Mon, 9 Feb 2026 07:27:33 +0000 (15:27 +0800)]
net: mctp: ensure our nlmsg responses are initialised
Syed Faraz Abrar (@farazsth98) from Zellic, and Pumpkin (@u1f383) from
DEVCORE Research Team working with Trend Micro Zero Day Initiative
report that a RTM_GETNEIGH will return uninitalised data in the pad
bytes of the ndmsg data.
Ensure we're initialising the netlink data to zero, in the link, addr
and neigh response messages.
Fixes: 831119f88781 ("mctp: Add neighbour netlink interface") Fixes: 06d2f4c583a7 ("mctp: Add netlink route management") Fixes: 583be982d934 ("mctp: Add device handling and netlink interface") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20260209-dev-mctp-nlmsg-v1-1-f1e30c346a43@codeconstruct.com.au Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: phy_port: Correctly recompute the port's linkmodes
a PHY-driven phy_port contains a 'supported' field containing the
linkmodes available on this port. This is populated based on :
- The PHY's reported features
- The DT representation of the connector
- The PHY's attach_mdi() callback
As these different attrbution methods work in conjunction, the helper
phy_port_update_supported() recomputes the final 'supported' value based
on the populated mediums, linkmodes and pairs.
However this recompute wasn't correctly implemented, and added more
modes than necessary by or'ing the medium-specific modes to the existing
support. Let's fix this and properly filter the modes.
net: phy: initialize the port support based on the PHY's for OF ports
With the phy_port infrastructure came an ethernet-connector binding,
allowing to represent the MDI of a PHY in devicetree. This allows
specifying the mediums and pairs of a port.
Let's initialize the port's supported list based on what the PHY
reports, so that we can then filter it with what the connector allows
using.
Ralf Lici [Fri, 30 Jan 2026 17:32:50 +0000 (18:32 +0100)]
ovpn: fix VPN TX bytes counting
In ovpn_net_xmit, after GSO segmentation and segment processing, the
first segment on the list is used to increment VPN TX statistics, which
fails to account for any subsequent segments in the chain.
Fix this by accumulating the length of every segment that successfully
passes skb_share_check into a tx_bytes variable. This ensures the peer
statistics accurately reflect the total data volume sent, regardless of
whether the original packet was segmented.
Fixes: 04ca14955f9a ("ovpn: store tunnel and transport statistics") Signed-off-by: Ralf Lici <ralf@mandelbit.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Ralf Lici [Fri, 30 Jan 2026 17:32:49 +0000 (18:32 +0100)]
ovpn: fix possible use-after-free in ovpn_net_xmit
When building the skb_list in ovpn_net_xmit, skb_share_check will free
the original skb if it is shared. The current implementation continues
to use the stale skb pointer for subsequent operations:
- peer lookup,
- skb_dst_drop (even though all segments produced by skb_gso_segment
will have a dst attached),
- ovpn_peer_stats_increment_tx.
Fix this by moving the peer lookup and skb_dst_drop before segmentation
so that the original skb is still valid when used. Return early if all
segments fail skb_share_check and the list ends up empty.
Also switch ovpn_peer_stats_increment_tx to use skb_list.next; the next
patch fixes the stats logic.
Ralf Lici [Fri, 30 Jan 2026 17:32:48 +0000 (18:32 +0100)]
ovpn: set sk_user_data before overriding callbacks
During initialization, we override socket callbacks and set sk_user_data
to an ovpn_socket instance. Currently, these two operations are
decoupled: callbacks are overridden before sk_user_data is set. While
existing callbacks perform safety checks for NULL or non-ovpn
sk_user_data, this condition causes a "half-formed" state where valid
packets arriving during attachment trigger error logs (e.g., "invoked on
non ovpn socket").
Set sk_user_data before overriding the callbacks so that it can be
accessed safely from them. Since we already check that the socket has no
sk_user_data before setting it, this remains safe even if an interrupt
accesses the socket after sk_user_data is set but before the callbacks
are overridden.
This also requires initializing all protocol-specific fields (such as
tcp_tx_work and peer links) before calling ovpn_socket_attach, ensuring
the ovpn_socket is fully formed before it becomes visible to any
callback.
Fixes: f6226ae7a0cd ("ovpn: introduce the ovpn_socket object") Signed-off-by: Ralf Lici <ralf@mandelbit.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Linus Torvalds [Thu, 12 Feb 2026 03:31:52 +0000 (19:31 -0800)]
Merge tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core & protocols:
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls
for small helper and stack canary overhead in the fast-path.
This generates better and faster code with very small or no text
size increases, as in many cases the call generated more code than
the actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage
by up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the
RX path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without
the HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified,
aligning IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the
rate shaper of sch_cake across multiple CPUs, while still enforcing
a single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations
that are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information,
saving cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most
protocols, avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies
between the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes
back online.
Driver API:
- Support for switching the working mode (automatic vs manual) of a
DPLL device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties,
to generalize polarity inversion requirements for differential
signaling.
- Add helper to create, prepare and enable managed clocks.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram
and NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the
used H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO,
leading to 12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new
layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN
metadata access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support multi-wiphy
devices and and pave the way for future device support in the
same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature"
* tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits)
bnge/bng_re: Add a new HSI
net: macb: Fix tx/rx malfunction after phy link down and up
af_unix: Fix memleak of newsk in unix_stream_connect().
net: ti: icssg-prueth: Add optional dependency on HSR
net: dsa: add basic initial driver for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add tag format for MxL862xx switches
dt-bindings: net: dsa: add MaxLinear MxL862xx
selftests: drivers: net: hw: Modify toeplitz.c to poll for packets
octeontx2-pf: Unregister devlink on probe failure
net: renesas: rswitch: fix forwarding offload statemachine
ionic: Rate limit unknown xcvr type messages
tcp: inet6_csk_xmit() optimization
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock()
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect()
ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6
ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update()
ipv6: use np->final in inet6_sk_rebuild_header()
ipv6: add daddr/final storage in struct ipv6_pinfo
net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup()
...
- Add bindings for Freescale AVIC, Realtek RTD1xxx system
controllers, Microchip 25AA010A EEPROM, OnSemi FIN3385, IEI
WT61P803 PUZZLE, Delta Electronics DPS-800-AB power supply,
Infineon IR35221 Digital Multi-phase Controller, Infineon PXE1610
Digital Dual Output 6+1 VR12.5 & VR13 CPU Controller,
socionext,uniphier-smpctrl, and xlnx,zynqmp-firmware
- Lots of trivial binding fixes to address warnings in DTS files.
These are mostly for arm64 platforms which is getting closer to be
warning free. Some public shaming has helped.
- Fix I2C bus node names in examples
- Drop obsolete brcm,vulcan-soc binding
- Drop unreferenced binding headers"
* tag 'devicetree-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (60 commits)
dt-bindings: interrupt-controller: Add compatiblie string fsl,imx(1|25|27|31|35)-avic
dt-bindings: soc: imx: add fsl,aips and fsl,emi compatible strings
dt-bindings: display: bridge: lt8912b: Drop reset gpio requirement
dt-bindings: firmware: fsl,scu: Mark multi-channel MU layouts as deprecated
cpufreq: s5pv210: Simplify with scoped for each OF child loop
dmaengine: fsl_raid: Simplify with scoped for each OF child loop
clk: imx: imx31: Simplify with scoped for each OF child loop
clk: imx: imx27: Simplify with scoped for each OF child loop
cdx: Use mutex guard to simplify error handling
cdx: Simplify with scoped for each OF child loop
powerpc/wii: Simplify with scoped for each OF child loop
powerpc/fsp2: Simplify with scoped for each OF child loop
ARM: exynos: Simplify with scoped for each OF child loop
ARM: at91: Simplify with scoped for each OF child loop
of: Add for_each_compatible_node_scoped() helper
dt-bindings: Fix emails with spaces or missing brackets
scripts/dtc: Update to upstream version v1.7.2-62-ga26ef6400bd8
dt-bindings: crypto: inside-secure,safexcel: Mandate only ring IRQs
dt-bindings: crypto: inside-secure,safexcel: Add SoC compatibles
of: reserved_mem: Fix placement of __free() annotation
...
Linus Torvalds [Thu, 12 Feb 2026 01:43:59 +0000 (17:43 -0800)]
Merge tag 'driver-core-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"Bus:
- Ensure bus->match() is consistently called with the device lock
held
- Improve type safety of bus_find_device_by_acpi_dev()
Devtmpfs:
- Parse 'devtmpfs.mount=' boot parameter with kstrtoint() instead of
simple_strtoul()
- Avoid sparse warning by making devtmpfs_context_ops static
IOMMU:
- Do not register the qcom_smmu_tbu_driver in arm_smmu_device_probe()
MAINTAINERS:
- Add the new driver-core mailing list (driver-core@lists.linux.dev)
to all relevant entries
- Add missing tree location for "FIRMWARE LOADER (request_firmware)"
- Add driver-model documentation to the "DRIVER CORE" entry
- Add missing driver-core maintainers to the "AUXILIARY BUS" entry
Misc:
- Change return type of attribute_container_register() to void; it
has always been infallible
- Do not export sysfs_change_owner(), sysfs_file_change_owner() and
device_change_owner()
- Move devres_for_each_res() from the public devres header to
drivers/base/base.h
- Do not use a static struct device for the faux bus; allocate it
dynamically
Revocable:
- Patches for the revocable synchronization primitive have been
scheduled for v7.0-rc1, but have been reverted as they need some
more refinement
Rust:
- Device:
- Support dev_printk on all device types, not just the core Device
struct; remove now-redundant .as_ref() calls in dev_* print
calls
- Devres:
- Introduce an internal reference count in Devres<T> to avoid a
deadlock condition in case of (indirect) nesting
- DMA:
- Allow drivers to tune the maximum DMA segment size via
dma_set_max_seg_size()
- I/O:
- Introduce the concept of generic I/O backends to handle
different kinds of device shared memory through a common
interface.
This enables higher-level concepts such as register
abstractions, I/O slices, and field projections to be built
generically on top.
In a first step, introduce the Io, IoCapable<T>, and IoKnownSize
trait hierarchy for sharing a common interface supporting offset
validation and bound-checking logic between I/O backends.
- Refactor MMIO to use the common I/O backend infrastructure
- Misc:
- Add __rust_helper annotations to C helpers for inlining into
Rust code
- Use "kernel vertical" style for imports
- Replace kernel::c_str! with C string literals
- Update ARef imports to use sync::aref
- Use pin_init::zeroed() for struct auxiliary_device_id and
debugfs file_operations initialization
- Use LKMM atomic types in debugfs doc-tests
- Various minor comment and documentation fixes
- PCI:
- Implement PCI configuration space accessors using the common I/O
backend infrastructure
- Document pci::Bar device endianness assumptions
- SoC:
- Abstractions for struct soc_device and struct soc_device_attribute
- Sample driver for soc::Device"
* tag 'driver-core-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (79 commits)
rust: devres: fix race condition due to nesting
rust: dma: add missing __rust_helper annotations
samples: rust: pci: Remove some additional `.as_ref()` for `dev_*` print
Revert "revocable: Revocable resource management"
Revert "revocable: Add Kunit test cases"
Revert "selftests: revocable: Add kselftest cases"
driver core: remove device_change_owner() export
sysfs: remove exports of sysfs_*change_owner()
driver core: disable revocable code from build
revocable: Add KUnit test for concurrent access
revocable: fix SRCU index corruption by requiring caller-provided storage
revocable: Add KUnit test for provider lifetime races
revocable: Fix races in revocable_alloc() using RCU
driver core: fix inverted "locked" suffix of driver_match_device()
rust: io: move MIN_SIZE and io_addr_assert to IoKnownSize
rust: pci: re-export ConfigSpace
rust: dma: allow drivers to tune max segment size
gpu: tyr: remove redundant `.as_ref()` for `dev_*` print
rust: auxiliary: use `pin_init::zeroed()` for device ID
rust: debugfs: use pin_init::zeroed() for file_operations
...
Linus Torvalds [Thu, 12 Feb 2026 01:20:38 +0000 (17:20 -0800)]
Merge tag 'pci-v7.0-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Don't try to enable Extended Tags on VFs since that bit is Reserved
and causes misleading log messages (Håkon Bugge)
- Initialize Endpoint Read Completion Boundary to match Root Port,
regardless of ACPI _HPX (Håkon Bugge)
- Apply _HPX PCIe Setting Record only to AER configuration, and only
when OS owns PCIe hotplug but not AER, to avoid clobbering Extended
Tag and Relaxed Ordering settings (Håkon Bugge)
Resource management:
- Move CardBus code to setup-cardbus.c and only build it when
CONFIG_CARDBUS is set (Ilpo Järvinen)
- Fix bridge window alignment with optional resources, where
additional alignment requirement was previously lost (Ilpo
Järvinen)
- Stop over-estimating bridge window size since they are now assigned
without any gaps between them (Ilpo Järvinen)
- Increase resource MAX_IORES_LEVEL to avoid /proc/iomem flattening
for nested bridges and endpoints (Ilpo Järvinen)
- Add pbus_mem_size_optional() to handle sizes of optional resources
(SR-IOV VF BARs, expansion ROMs, bridge windows) (Ilpo Järvinen)
- Don't claim disabled bridge windows to avoid spurious claim
failures (Ilpo Järvinen)
Driver binding:
- Fix device reference leak in pcie_port_remove_service() (Uwe
Kleine-König)
- Move pcie_port_bus_match() and pcie_port_bus_type to PCIe-specific
portdrv.c (Uwe Kleine-König)
- Convert portdrv to use pcie_port_bus_type.probe() and .remove()
callbacks so .probe() and .remove() can eventually be removed from
struct device_driver (Uwe Kleine-König)
Error handling:
- Clear stale errors on reporting agents upon probe so they don't
look like recent errors (Lukas Wunner)
- Add generic RAS tracepoint for hotplug events (Shuai Xue)
- Add RAS tracepoint for link speed changes (Shuai Xue)
Power management:
- Avoid redundant delay on transition from D3hot to D3cold if the
device was already in D3hot (Brian Norris)
- Prevent runtime suspend until devices are fully initialized to
avoid saving incompletely configured device state (Brian Norris)
Power control:
- Add power_on/off callbacks with generic signature to pwrseq,
tc9563, and slot drivers so they can be used by pwrctrl core
(Manivannan Sadhasivam)
- Add PCIe M.2 connector support to the slot pwrctrl driver
(Manivannan Sadhasivam)
- Switch to pwrctrl interfaces to create, destroy, and power on/off
devices, calling them from host controller drivers instead of the
PCI core (Manivannan Sadhasivam)
- Drop qcom .assert_perst() callbacks since this is now done by the
controller driver instead of the pwrctrl driver (Manivannan
Sadhasivam)
Virtualization:
- Remove an incorrect unlock in pci_slot_trylock() error handling
(Jinhui Guo)
- Lock the bridge device for slot reset (Keith Busch)
- Enable ACS after IOMMU configuration on OF platforms so ACS is
enabled an all devices; previously the first device enumerated
(typically a Root Port) didn't have ACS enabled (Manivannan
Sadhasivam)
- Disable ACS Source Validation for IDT 0x80b5 and 0x8090 switches to
work around hardware erratum; previously ACS SV was only
temporarily disabled, which worked for enumeration but not after
reset (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Release per-CPU pgmap ref when vm_insert_page() fails to avoid hang
when removing the PCI device (Hou Tao)
- Remove incorrect p2pmem_alloc_mmap() warning about page refcount
(Hou Tao)
Endpoint framework:
- Add configfs sub-groups synchronously to avoid NULL pointer
dereference when racing with removal (Liu Song)
- Fix swapped parameters in pci_{primary/secondary}_epc_epf_unlink()
functions (Manikanta Maddireddy)
- Add DT binding and driver support for SA8255p Endpoint being
configured by firmware (Mrinmay Sarkar)
- Parse PERST# from all PCIe bridge nodes for future platforms that
will have PERST# in Switch Downstream Ports as well as in Root
Ports (Manivannan Sadhasivam)
Renesas RZ/G3S PCIe controller driver:
- Use pci_generic_config_write() since the writability provided by
the custom wrapper is unnecessary (Claudiu Beznea)
SOPHGO PCIe controller driver:
- Disable ASPM L0s and L1 on Sophgo 2044 PCIe Root Ports (Inochi
Amaoto)
Synopsys DesignWare PCIe controller driver:
- Extend PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() to return a
pointer to the preceding Capability, to allow removal of
Capabilities that are advertised but not fully implemented (Qiang
Yu)
- Remove MSI and MSI-X Capabilities in platforms that can't support
them, so the PCI core automatically falls back to INTx (Qiang Yu)
- Add ASPM L1.1 and L1.2 Substates context to debugfs ltssm_status
for drivers that support this (Shawn Lin)
- Skip PME_Turn_Off broadcast and L2/L3 transition during suspend if
link is not up to avoid an unnecessary timeout (Manivannan
Sadhasivam)
- Revert dw-rockchip, qcom, and DWC core changes that used link-up
IRQs to trigger enumeration instead of waiting for link to be up
because the PCI core doesn't allocate bus number space for
hierarchies that might be attached (Niklas Cassel)
- Make endpoint iATU entry for MSI permanent instead of programming
it dynamically, which is slow and racy with respect to other
concurrent traffic, e.g., eDMA (Koichiro Den)
- Use iMSI-RX MSI target address when possible to fix endpoints using
32-bit MSI (Shawn Lin)
- Allow DWC host controller driver probe to continue if device is not
found or found but inactive; only fail when there's an error with
the link (Manivannan Sadhasivam)
- For controllers like NXP i.MX6QP and i.MX7D, where LTSSM registers
are not accessible after PME_Turn_Off, simply wait 10ms instead of
polling for L2/L3 Ready (Richard Zhu)
- Use multiple iATU entries to map large bridge windows and DMA
ranges when necessary instead of failing (Samuel Holland)
- Add EPC dynamic_inbound_mapping feature bit for Endpoint
Controllers that can update BAR inbound address translation without
requiring EPF driver to clear/reset the BAR first, and advertise it
for DWC-based Endpoints (Koichiro Den)
- Add EPC subrange_mapping feature bit for Endpoint Controllers that
can map multiple independent inbound regions in a single BAR,
implement subrange mapping, advertise it for DWC-based Endpoints,
and add Endpoint selftests for it (Koichiro Den)
- Make resizable BARs work for Endpoint multi-PF configurations;
previously it only worked for PF 0 (Aksh Garg)
- Fix Endpoint non-PF 0 support for BAR configuration, ATU mappings,
and Address Match Mode (Aksh Garg)
- Set up iATU when ECAM is enabled; previously IO and MEM outbound
windows weren't programmed, and ECAM-related iATU entries weren't
restored after suspend/resume, so config accesses failed (Krishna
Chaitanya Chundru)
Miscellaneous:
- Use system_percpu_wq and WQ_PERCPU to explicitly request per-CPU
work so WQ_UNBOUND can eventually be removed (Marco Crivellari)"
* tag 'pci-v7.0-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (176 commits)
PCI/bwctrl: Disable BW controller on Intel P45 using a quirk
PCI: Disable ACS SV for IDT 0x8090 switch
PCI: Disable ACS SV for IDT 0x80b5 switch
PCI: Cache ACS Capabilities register
PCI: Enable ACS after configuring IOMMU for OF platforms
PCI: Add ACS quirk for Pericom PI7C9X2G404 switches [12d8:b404]
PCI: Add ACS quirk for Qualcomm Hamoa & Glymur
PCI: Use device_lock_assert() to verify device lock is held
PCI: Use lockdep_assert_held(pci_bus_sem) to verify lock is held
PCI: Fix pci_slot_lock () device locking
PCI: Fix pci_slot_trylock() error handling
PCI: Mark Nvidia GB10 to avoid bus reset
PCI: Mark ASM1164 SATA controller to avoid bus reset
PCI: host-generic: Avoid reporting incorrect 'missing reg property' error
PCI/PME: Replace RMW of Root Status register with direct write
PCI/AER: Clear stale errors on reporting agents upon probe
PCI: Don't claim disabled bridge windows
PCI: rzg3s-host: Fix device node reference leak in rzg3s_pcie_host_parse_port()
PCI: dwc: Fix missing iATU setup when ECAM is enabled
PCI: dwc: Clean up iATU index usage in dw_pcie_iatu_setup()
...
* tag 'for-7.0/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (35 commits)
dm mpath: make pg_init_delay_msecs settable
Revert "dm: fix a race condition in retrieve_deps"
dm mpath: Add missing dm_put_device when failing to get scsi dh name
dm vdo encodings: clean up header and version functions
dm: use bio_clone_blkg_association
dm: fix excessive blk-crypto operations for invalid keys
dm-verity: fix section mismatch error
dm-unstripe: fix mapping bug when there are multiple targets in a table
dm-integrity: fix recalculation in bitmap mode
dm-bufio: avoid redundant buffer_tree lookups
dm-bufio: merge cache_put() into cache_put_and_wake()
selftests: add dm-verity keyring selftests
dm-verity: add dm-verity keyring
dm: clear cloned request bio pointer when last clone bio completes
dm-verity: fix up various workqueue-related comments
dm-verity: switch to bio_advance_iter_single()
dm-verity: consolidate the BH and normal work structs
dm: add WQ_PERCPU to alloc_workqueue users
dm-integrity: fix a typo in the code for write/discard race
dm: use READ_ONCE in dm_blk_report_zones
...
Linus Torvalds [Thu, 12 Feb 2026 00:36:08 +0000 (16:36 -0800)]
Merge tag 'iommu-updates-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core changes:
- Rust bindings for IO-pgtable code
- IOMMU page allocation debugging support
- Disable ATS during PCI resets
Intel VT-d changes:
- Skip dev-iotlb flush for inaccessible PCIe device
- Flush cache for PASID table before using it
- Use right invalidation method for SVA and NESTED domains
- Ensure atomicity in context and PASID entry updates
AMD-Vi changes:
- Support for nested translations
- Other minor improvements
ARM-SMMU-v2 changes:
- Configure SoC-specific prefetcher settings for Qualcomm's "MDSS"
ARM-SMMU-v3 changes:
- Improve CMDQ locking fairness for pathetically small queue sizes
- Remove tracking of the IAS as this is only relevant for AArch32 and
was causing C_BAD_STE errors
- Add device-tree support for NVIDIA's CMDQV extension
- Allow some hitless transitions for the 'MEV' and 'EATS' STE fields
- Don't disable ATS for nested S1-bypass nested domains
- Additions to the kunit selftests"
* tag 'iommu-updates-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (54 commits)
iommupt: Always add IOVA range to iotlb_gather in gather_range_pages()
iommu/amd: serialize sequence allocation under concurrent TLB invalidations
iommu/amd: Fix type of type parameter to amd_iommufd_hw_info()
iommu/arm-smmu-v3: Do not set disable_ats unless vSTE is Translate
iommu/arm-smmu-v3-test: Add nested s1bypass/s1dssbypass coverage
iommu/arm-smmu-v3: Mark EATS_TRANS safe when computing the update sequence
iommu/arm-smmu-v3: Mark STE MEV safe when computing the update sequence
iommu/arm-smmu-v3: Add update_safe bits to fix STE update sequence
iommu/arm-smmu-v3: Add device-tree support for CMDQV driver
iommu/tegra241-cmdqv: Decouple driver from ACPI
iommu/arm-smmu-qcom: Restore ACTLR settings for MDSS on sa8775p
iommu/vt-d: Fix race condition during PASID entry replacement
iommu/vt-d: Clear Present bit before tearing down context entry
iommu/vt-d: Clear Present bit before tearing down PASID entry
iommu/vt-d: Flush piotlb for SVM and Nested domain
iommu/vt-d: Flush cache for PASID table before using it
iommu/vt-d: Flush dev-IOTLB only when PCIe device is accessible in scalable mode
iommu/vt-d: Skip dev-iotlb flush for inaccessible PCIe device without scalable mode
rust: iommu: fix `srctree` link warning
rust: iommu: fix Rust formatting
...
Linus Torvalds [Wed, 11 Feb 2026 23:57:08 +0000 (15:57 -0800)]
Merge tag 'landlock-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull landlock updates from Mickaël Salaün:
- extend Landlock to enforce restrictions on a whole process, similarly
to the seccomp's TSYNC flag
- refactor data structures to simplify code and improve performance
- add documentation to cover missing parts
* tag 'landlock-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
mailmap: Add entry for Mickaël Salaün
landlock: Transpose the layer masks data structure
landlock: Add access_mask_subset() helper
selftests/landlock: Add filesystem access benchmark
landlock: Document audit blocker field format
landlock: Add errata documentation section
landlock: Add backwards compatibility for restrict flags
landlock: Refactor TCP socket type check
landlock: Minor reword of docs for TCP access rights
landlock: Document LANDLOCK_RESTRICT_SELF_TSYNC
selftests/landlock: Add LANDLOCK_RESTRICT_SELF_TSYNC tests
landlock: Multithreading support for landlock_restrict_self()
Linus Torvalds [Wed, 11 Feb 2026 23:53:00 +0000 (15:53 -0800)]
Merge tag 'integrity-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"Just two bug fixes: IMA's detecting scripts (bprm_creds_for_exec), and
calculating the EVM HMAC"
* tag 'integrity-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
evm: Use ordered xattrs list to calculate HMAC in evm_init_hmac()
ima: Fix stack-out-of-bounds in is_bprm_creds_for_exec()
Linus Torvalds [Wed, 11 Feb 2026 23:47:37 +0000 (15:47 -0800)]
Merge tag 'Smack-for-7.0' of https://github.com/cschaufler/smack-next
Pull smack updates from Casey Schaufler:
"Two improvements to the code for setting the CIPSO Domain Of
Interpretation (DOI), a seldom used feature, and a formatting change"
* tag 'Smack-for-7.0' of https://github.com/cschaufler/smack-next:
smack: /smack/doi: accept previously used values
smack: /smack/doi must be > 0
security: smack: fix indentation in smack_access.c
Linus Torvalds [Wed, 11 Feb 2026 22:36:47 +0000 (14:36 -0800)]
Merge tag 'printk-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Check all mandatory callbacks when registering nbcon consoles
- Fix some compiler warnings
* tag 'printk-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
vsnprintf: drop __printf() attributes on binary printing functions
printf: convert test_hashed into macro
printk: nbcon: Check for device_{lock,unlock} callbacks
Linus Torvalds [Wed, 11 Feb 2026 22:12:50 +0000 (14:12 -0800)]
Merge tag 'slab-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab updates from Vlastimil Babka:
- The percpu sheaves caching layer was introduced as opt-in in 6.18 and
now we enable it for all caches and remove the previous cpu (partial)
slab caching mechanism.
Besides the lower locking overhead and much more likely fastpath when
freeing, this removes the rather complicated code related to the cpu
slab lockless fastpaths (using this_cpu_try_cmpxchg128/64) and all
its complications for PREEMPT_RT or kmalloc_nolock().
The lockless slab freelist+counters update operation using
try_cmpxchg128/64 remains and is crucial for freeing remote NUMA
objects, and to allow flushing objects from sheaves to slabs mostly
without the node list_lock (Vlastimil Babka)
- Eliminate slabobj_ext metadata overhead when possible. Instead of
using kmalloc() to allocate the array for memcg and/or allocation
profiling tag pointers, use leftover space in a slab or per-object
padding due to alignment (Harry Yoo)
- Various followup improvements to the above (Hao Li)
* tag 'slab-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab: (39 commits)
slub: let need_slab_obj_exts() return false if SLAB_NO_OBJ_EXT is set
mm/slab: only allow SLAB_OBJ_EXT_IN_OBJ for unmergeable caches
mm/slab: place slabobj_ext metadata in unused space within s->size
mm/slab: move [__]ksize and slab_ksize() to mm/slub.c
mm/slab: save memory by allocating slabobj_ext array from leftover
mm/memcontrol,alloc_tag: handle slabobj_ext access under KASAN poison
mm/slab: use stride to access slabobj_ext
mm/slab: abstract slabobj_ext access via new slab_obj_ext() helper
ext4: specify the free pointer offset for ext4_inode_cache
mm/slab: allow specifying free pointer offset when using constructor
mm/slab: use unsigned long for orig_size to ensure proper metadata align
slub: clarify object field layout comments
mm/slab: avoid allocating slabobj_ext array from its own slab
slub: avoid list_lock contention from __refill_objects_any()
mm/slub: cleanup and repurpose some stat items
mm/slub: remove DEACTIVATE_TO_* stat items
slab: remove frozen slab checks from __slab_free()
slab: update overview comments
slab: refill sheaves from all nodes
slab: remove unused PREEMPT_RT specific macros
...
Linus Torvalds [Wed, 11 Feb 2026 21:40:35 +0000 (13:40 -0800)]
Merge tag 'kbuild-7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild/Kconfig updates from Nathan Chancellor:
"Kbuild:
- Drop '*_probe' pattern from modpost section check allowlist, which
hid legitimate warnings (Johan Hovold)
- Disable -Wtype-limits altogether, instead of enabling at W=2
(Vincent Mailhol)
- Improve UAPI testing to skip testing headers that require a libc
when CONFIG_CC_CAN_LINK is not set, opening up testing of headers
with no libc dependencies to more environments (Thomas Weißschuh)
- Update gendwarfksyms documentation with required dependencies
(Jihan LIN)
- Reject invalid LLVM= values to avoid unintentionally falling back
to system toolchain (Thomas Weißschuh)
- Add a script to help run the kernel build process in a container
for consistent environments and testing (Guillaume Tucker)
- Simplify kallsyms by getting rid of the relative base (Ard
Biesheuvel)
- Performance and usability improvements to scripts/make_fit.py
(Simon Glass)
- Minor various clean ups and fixes
Kconfig:
- Move XPM icons to individual files, clearing up GTK deprecation
warnings (Rostislav Krasny)
- Support
depends on FOO if BAR
as syntactic sugar for
depends on FOO || !BAR
(Nicolas Pitre, Graham Roff)
- Refactor merge_config.sh to use awk over shell/sed/grep,
dramatically speeding up processing large number of config
fragments (Anders Roxell, Mikko Rapeli)"
* tag 'kbuild-7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux: (39 commits)
kbuild: remove dependency of run-command on config
scripts/make_fit: Compress dtbs in parallel
scripts/make_fit: Support a few more parallel compressors
kbuild: Support a FIT_EXTRA_ARGS environment variable
scripts/make_fit: Move dtb processing into a function
scripts/make_fit: Support an initial ramdisk
scripts/make_fit: Speed up operation
rust: kconfig: Don't require RUST_IS_AVAILABLE for rustc-option
MAINTAINERS: Add scripts/install.sh into Kbuild entry
modpost: Amend ppc64 save/restfpr symnames for -Os build
MIPS: tools: relocs: Ship a definition of R_MIPS_PC32
streamline_config.pl: remove superfluous exclamation mark
kbuild: dummy-tools: Add python3
scripts: kconfig: merge_config.sh: warn on duplicate input files
scripts: kconfig: merge_config.sh: use awk in checks too
scripts: kconfig: merge_config.sh: refactor from shell/sed/grep to awk
kallsyms: Get rid of kallsyms relative base
mips: Add support for PC32 relocations in vmlinux
Documentation: dev-tools: add container.rst page
scripts: add tool to run containerized builds
...
Linus Torvalds [Wed, 11 Feb 2026 21:35:24 +0000 (13:35 -0800)]
Merge tag 'sched_ext-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext updates from Tejun Heo:
- Move C example schedulers back from the external scx repo to
tools/sched_ext as the authoritative source. scx_userland and
scx_pair are returning while scx_sdt (BPF arena-based task data
management) is new. These schedulers will be dropped from the
external repo.
- Improve error reporting by adding scx_bpf_error() calls when DSQ
creation fails across all in-tree schedulers
- Avoid redundant irq_work_queue() calls in destroy_dsq() by only
queueing when llist_add() indicates an empty list
- Fix flaky init_enable_count selftest by properly synchronizing
pre-forked children using a pipe instead of sleep()
* tag 'sched_ext-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
selftests/sched_ext: Fix init_enable_count flakiness
tools/sched_ext: Fix data header access during free in scx_sdt
tools/sched_ext: Add error logging for dsq creation failures in remaining schedulers
tools/sched_ext: add arena based scheduler
tools/sched_ext: add scx_pair scheduler
tools/sched_ext: add scx_userland scheduler
sched_ext: Add error logging for dsq creation failures
sched_ext: Avoid multiple irq_work_queue() calls in destroy_dsq()
Linus Torvalds [Wed, 11 Feb 2026 21:20:50 +0000 (13:20 -0800)]
Merge tag 'cgroup-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- cpuset changes:
- Continue separating v1 and v2 implementations by moving more
v1-specific logic into cpuset-v1.c
- Improve partition handling. Sibling partitions are no longer
invalidated on cpuset.cpus conflict, cpuset.cpus changes no longer
fail in v2, and effective_xcpus computation is made consistent
- Fix partition effective CPUs overlap that caused a warning on
cpuset removal when sibling partitions shared CPUs
- Increase the maximum cgroup subsystem count from 16 to 32 to
accommodate future subsystem additions
- Misc cleanups and selftest improvements including switching to
css_is_online() helper, removing dead code and stale documentation
references, using lockdep_assert_cpuset_lock_held() consistently, and
adding polling helpers for asynchronously updated cgroup statistics
* tag 'cgroup-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cpuset: fix overlap of partition effective CPUs
cgroup: increase maximum subsystem count from 16 to 32
cgroup: Remove stale cpu.rt.max reference from documentation
cpuset: replace direct lockdep_assert_held() with lockdep_assert_cpuset_lock_held()
cgroup/cpuset: Move the v1 empty cpus/mems check to cpuset1_validate_change()
cgroup/cpuset: Don't invalidate sibling partitions on cpuset.cpus conflict
cgroup/cpuset: Don't fail cpuset.cpus change in v2
cgroup/cpuset: Consistently compute effective_xcpus in update_cpumasks_hier()
cgroup/cpuset: Streamline rm_siblings_excl_cpus()
cpuset: remove dead code in cpuset-v1.c
cpuset: remove v1-specific code from generate_sched_domains
cpuset: separate generate_sched_domains for v1 and v2
cpuset: move update_domain_attr_tree to cpuset_v1.c
cpuset: add cpuset1_init helper for v1 initialization
cpuset: add cpuset1_online_css helper for v1-specific operations
cpuset: add lockdep_assert_cpuset_lock_held helper
cpuset: Remove unnecessary checks in rebuild_sched_domains_locked
cgroup: switch to css_is_online() helper
selftests: cgroup: Replace sleep with cg_read_key_long_poll() for waiting on nr_dying_descendants
selftests: cgroup: make test_memcg_sock robust against delayed sock stats
...
Linus Torvalds [Wed, 11 Feb 2026 21:13:32 +0000 (13:13 -0800)]
Merge tag 'wq-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
- Rework the rescuer to process work items one-by-one instead of
slurping all pending work items in a single pass.
As there is only one rescuer per workqueue, a single long-blocking
work item could cause high latency for all tasks queued behind it,
even after memory pressure is relieved and regular kworkers become
available to service them.
- Add CONFIG_BOOTPARAM_WQ_STALL_PANIC build-time option and
workqueue.panic_on_stall_time parameter for time-based stall panic,
giving systems more control over workqueue stall handling.
- Replace BUG_ON() with panic() in the stall panic path for clearer
intent and more informative output.
* tag 'wq-for-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: replace BUG_ON with panic in panic_on_wq_watchdog
workqueue: add time-based panic for stalls
workqueue: add CONFIG_BOOTPARAM_WQ_STALL_PANIC option
workqueue: Process extra works in rescuer on memory pressure
workqueue: Process rescuer work items one-by-one using a cursor
workqueue: Make send_mayday() take a PWQ argument directly
Thomas Gleixner [Tue, 10 Feb 2026 16:20:51 +0000 (17:20 +0100)]
sched/mmcid: Don't assume CID is CPU owned on mode switch
Shinichiro reported a KASAN UAF, which is actually an out of bounds access
in the MMCID management code.
CPU0 CPU1
T1 runs in userspace
T0: fork(T4) -> Switch to per CPU CID mode
fixup() set MM_CID_TRANSIT on T1/CPU1
T4 exit()
T3 exit()
T2 exit()
T1 exit() switch to per task mode
---> Out of bounds access.
As T1 has not scheduled after T0 set the TRANSIT bit, it exits with the
TRANSIT bit set. sched_mm_cid_remove_user() clears the TRANSIT bit in
the task and drops the CID, but it does not touch the per CPU storage.
That's functionally correct because a CID is only owned by the CPU when
the ONCPU bit is set, which is mutually exclusive with the TRANSIT flag.
Now sched_mm_cid_exit() assumes that the CID is CPU owned because the
prior mode was per CPU. It invokes mm_drop_cid_on_cpu() which clears the
not set ONCPU bit and then invokes clear_bit() with an insanely large
bit number because TRANSIT is set (bit 29).
Prevent that by actually validating that the CID is CPU owned in
mm_drop_cid_on_cpu().
Fixes: 007d84287c74 ("sched/mmcid: Drop per CPU CID immediately when switching to per task mode") Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Tested-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Cc: stable@vger.kernel.org Closes: https://lore.kernel.org/aYsZrixn9b6s_2zL@shinmob Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 11 Feb 2026 20:55:44 +0000 (12:55 -0800)]
Merge tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights:
- amdgpu support for lots of new IP blocks which means newer GPUs
- xe has a lot of SR-IOV and SVM improvements
- lots of intel display refactoring across i915/xe
- msm has more support for gen8 platforms
- Given up on kgdb/kms integration, it's too hard on modern hw
core:
- drop kgdb support
- replace system workqueue with percpu
- account for property blobs in memcg
- MAINTAINERS updates for xe + buddy
rust:
- Fix documentation for Registration constructors
- Use pin_init::zeroed() for fops initialization
- Annotate DRM helpers with __rust_helper
- Improve safety documentation for gem::Object::new()
- Update AlwaysRefCounted imports
- mm: Prevent integer overflow in page_align()
i915/xe display:
- Expose sharpness only if num_scalers is >= 2
- Add initial Xe3P_LPD for NVL
- BMG FBC support
- Add MTL+ platforms to support dpll framework
_ fix DIMM_S DRM decoding on ICL
- Return to using AUX interrupts
- PSR/Panel replay refactoring
- use consolidation HDMI tables
- Xe3_LPD CD2X dividier changes
xe:
- vfio: add vfio_pci for intel GPU
- multi queue support
- dynamic pagemaps and multi-device SVM
- expose temp attribs in hwmon
- NO_COMPRESSION bo flag
- expose MERT OA unit
- sysfs survivability refactor
- SRIOV PF: add MERT support
- enable SR-IOV VF migration
- Enable I2C/NVM on Crescent Island
- Xe3p page reclaimation support
- introduce SRIOV scheduler groups
- add SoC remappt support in system controller
- insert compiler barriers in GuC code
- define NVL GuC firmware
- handle GT resume failure
- fix drm scheduler layering violations
- enable GSC loading and PXP for PTL
- disable GuC Power DCC strategy on PTL
- unregister drm device on probe error
i915:
- move to kernel standard fault injection
- bump recommended GuC version for DG2 and MTL
amdgpu:
- SMUIO 15.x, PSP 15.x support
- IH 6.1.1/7.1 support
- MMHUB 3.4/4.2 support
- GC 11.5.4/12.1 support
- SDMA 6.1.4/7.1/7.11.4 support
- JPEG 5.3 support
- UserQ updates
- GC 9 gfx queue reset support
- TTM memory ops parallelization
- convert legacy logging to new helpers
- DC analog fixes
amdkfd:
- GC 11.5.4/12.1 suppport
- SDMA 6.1.4/7.1 support
- per context support
- increase kfd process hash table
- Reserved SDMA rework
radeon:
- convert legacy logging to new helpers
- use devm for i2c adapters
msm:
- GPU
- Document a612/RGMU dt bindings
- UBWC 6.0 support (for A840 / Kaanapali)
- a225 support
- DPU:
- Switch to use virtual planes by default
- Fix DSI CMD panels on DPU 3.x
- Rewrite format handling to remove intermediate representation
- Fix watchdog on DPU 8.x+
- Fix TE / Vsync source setting on DPU 8.x+
- Add 3D_Mux on SC7280
- Kaanapali platform support
- Fix UBWC register programming
- Make RM reserve DSPP-enabled mixers for CRTCs with LMs
- Gamma correction support
- DP:
- Enable support for eDP 1.4+ link rate tables
- Fix MDSS1 DP indices on SA8775P, making them to work
- Fix msm_dp_ctrl_config_msa() to work with LLVM 20
- DSI:
- Document QCS8300 as compatible with SA8775P
- Kaanapali platform support
- DSI PHY:
- switch to divider_determine_rate()
- MDP5:
- Drop support for MSM8998, SDM660 and SDM630 (switch over to DPU)
- MDSS:
- Kaanapali platform support
- Fixed UBWC register programming
nova-core:
- Prepare for Turing support. This includes parsing and handling
Turing-specific firmware headers and sections as well as a Turing
Falcon HAL implementation
- Get rid of the Result<impl PinInit<T, E>> anti-pattern
- Relocate initializer-specific code into the appropriate initializer
- Use CStr::from_bytes_until_nul() to remove custom helpers
- Improve handling of unexpected firmware values
- Clean up redundant debug prints
- Replace c_str!() with native Rust C-string literals
- Update nova-core task list
nova:
- Align GEM object size to system page size
tyr:
- Use generated uAPI bindings for GpuInfo
- Replace manual sleeps with read_poll_timeout()
- Replace c_str!() with native Rust C-string literals
- Suppress warnings for unread fields
- Fix incorrect register name in print statement
nouveau:
- fix big page table support races in PTE management
- improve reclocking on tegra 186+
amdxdna:
- fix suspend race conditions
- improve handling of zero tail pointers
- fix cu_idx overwritten during command setup
- enable hardware context priority
- remove NPU2 support
- update message buffer allocation requirements
- update firmware version check
ast:
- support imported cursor buffers
- big endian fixes
etnaviv:
- add PPU flop reset support
imagination:
- add AM62P support
- introduce hw version checks
ivpu:
- implement warm boot flow
panfrost:
- add bo sync ioctl
- add GPU_PM_RT support for RZ/G3E SoC
panthor:
- add bo sync ioctl
- enable timestamp propagation
- scheduler robustness improvements
- VM termination fixes
- huge page support
rockchip:
- RK3368 HDMI Support
- get rid of atomic_check fixups
- RK3506 support
- RK3576/RK3588 improved HPD handling
rz-du:
- RZ/V2H(P) MIPI-DSI Support
v3d:
- fix DMA segment size
- convert to new logging helpers
mediatek:
- move DP training to hotplug thread
- convert logging to new helpers
- add support for HS speed DSI
- Genio 510/700/1200-EVK, Radxa NIO-12L HDMI support
atmel-hlcdc:
- switch to drmm resource
- support nomodeset
- use newer helpers
hisilicon:
- fix various DP bugs
renesas:
- fix kernel panic on reboot
exynos:
- fix vidi_connection_ioctl using wrong device
- fix vidi_connection deref user ptr
- fix concurrency regression with vidi_context
vkms:
- add configfs support for display configuration
* tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel: (1610 commits)
drm/xe/pm: Disable D3Cold for BMG only on specific platforms
drm/xe: Fix kerneldoc for xe_tlb_inval_job_alloc_dep
drm/xe: Fix kerneldoc for xe_gt_tlb_inval_init_early
drm/xe: Fix kerneldoc for xe_migrate_exec_queue
drm/xe/query: Fix topology query pointer advance
drm/xe/guc: Fix kernel-doc warning in GuC scheduler ABI header
drm/xe/guc: Fix CFI violation in debugfs access.
accel/amdxdna: Move RPM resume into job run function
accel/amdxdna: Fix incorrect DPM level after suspend/resume
nouveau/vmm: start tracking if the LPT PTE is valid. (v6)
nouveau/vmm: increase size of vmm pte tracker struct to u32 (v2)
nouveau/vmm: rewrite pte tracker using a struct and bitfields.
accel/amdxdna: Fix incorrect error code returned for failed chain command
accel/amdxdna: Remove hardware context status
drm/bridge: imx8qxp-pixel-combiner: Fix bailout for imx8qxp_pc_bridge_probe()
drm/panel: ilitek-ili9882t: Remove duplicate initializers in tianma_il79900a_dsc
drm/i915/display: fix the pixel normalization handling for xe3p_lpd
drm/exynos: vidi: use ctx->lock to protect struct vidi_context member variables related to memory alloc/free
drm/exynos: vidi: fix to avoid directly dereferencing user pointer
drm/exynos: vidi: use priv->vidi_dev for ctx lookup in vidi_connection_ioctl()
...
Linus Torvalds [Wed, 11 Feb 2026 20:20:25 +0000 (12:20 -0800)]
Merge tag 'media/v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Add support for GMSL1 and GMSL‑coax modules (PCI mgb4)
- Add driver for TI VIP
- AV1 – first kernel support (pixel‑format, decoder, transcoder)
- Three new camera‑sensor drivers (os05b10, s5k3m5, s5kjn1)
- Synopsys CSI‑2 receiver driver
- Verisilicon & rkvdec – major fixes and enhancements
- IPU6 (and 7) fixes and preparation for metadata
- omap3isp: v4l2-compliance updates
- Fix DVB streaming, drop wait_prepare/finish (dvb/vb2)
* tag 'media/v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (307 commits)
media: uvcvideo: Pass allocation size directly to uvc_alloc_urb_buffer
media: uvcvideo: Fix allocation for small frame sizes
media: uvcvideo: Return queued buffers on start_streaming() failure
media: uvcvideo: Create an ID namespace for streaming output terminals
media: rkvdec: Add HEVC support for the VDPU383 variant
media: rkvdec: Add HEVC support for the VDPU381 variant
media: rkvdec: Add H264 support for the VDPU383 variant
media: rkvdec: Add H264 support for the VDPU381 variant
media: rkvdec: Disable multicore support
media: rkvdec: Enable all clocks without naming them
media: rkvdec: Support per-variant interrupt handler
media: rkvdec: Add RCB and SRAM support
media: rkvdec: Add variant specific coded formats list
media: rkvdec: Move hevc functions to common file
media: rkvdec: Move h264 functions to common file
media: rkvdec: Use structs to represent the HW RPS
media: rkvdec: Move cabac tables to their own source file
media: rkvdec: Switch to using structs instead of writel
media: visl: Add HEVC short and long term RPS sets
media: v4l2-ctrls: Add hevc_ext_sps_[ls]t_rps controls
...
Linus Torvalds [Wed, 11 Feb 2026 19:43:00 +0000 (11:43 -0800)]
Merge tag 'sound-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been relatively calm for a new era; majority of changes are for
ASoC, mostly device-specific changes, while there are a bit of
cleanups in core stuff. A few SPI API and regmap updates are included
to be used by sound drivers, too.
Core:
- A few trivial cleanups about __free() and runtime PM macros
- Convert to new snd_seq_bus binding
ASoC:
- Generic SDCA support for reporting jack events
- Continuing platform support, cleanup and feature improvements for
AMD, Intel, Qualcomm and SOF code
- Platform description improvements for the Cirrus drivers
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B
HD- and USB-audio:
- Many quirks as usual"
* tag 'sound-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: usb-audio: Add DSD support for iBasso DC04U
ALSA: mixer: oss: Add card disconnect checkpoints
ASoC: SOF: ipc4-control: Set correct error code in refresh_bytes_control
ASoC: SOF: Intel: select CONFIG_SND_HDA_EXT_CORE from SND_SOC_SOF_HDA_COMMON
ALSA: usb-audio: Add iface reset and delay quirk for AB13X USB Audio
ASoC: amd: maintainer information
ALSA: ctxfi: Add quirk for SE-300PCIE variant (160b:0102)
ALSA: hda/generic: fix typos in comments
ALSA: hda/realtek - Enable mute LEDs on HP ENVY x360 15-es0xxx
ALSA: hda/conexant: Add quirk for HP ZBook Studio G4
ASoC: fsl_asrc_dma: allocate memory from dma device
ASoC: fsl_asrc: Add support for i.MX952 platform
ASoC: fsl_asrc_m2m: Add option to start ASRC before DMA device for M2M
ASoC: dt-bindings: fsl,imx-asrc: Add support for i.MX952 platform
ALSA: oss: delete self assignment
ASoC: rockchip: spdif: Convert to FIELD_PREP
ASoC: rockchip: spdif: Fill IEC958 CS info per params
ASoC: rockchip: spdif: Add support for format S32_LE
ASoC: rockchip: spdif: Add support for set mclk rate
ASoC: rockchip: spdif: Swap PCM and DAI component registration order
...
Although 1394 OHCI specification does not impose any restriction on
the memory size dedicated to these DMA contexts, 1394 OHCI PCI driver
allocates pages for convenience when mapping them into either kernel
space or userspace VMA. The driver previously used dma_alloc_pages()
for both page allocation and mapping creation, even though this
kernel API is rarely used. Following discussions questioning the
page-oriented kernel API in the DMA layer, the driver has been
refactored to avoid using this API. In addition, the use of private
members in the allocated pages has been removed following
long-standing concern.
- Allocate variable-sized buffer for isochronous context header
1394 OHCI PCI driver previously allocated a single page for
isochronous context header. As a result, the buffer size for the
header was fixed to PAGE_SIZE, which imposed a limitation on IEC
61883-1/6 packet streaming engine. Consequently, the ALSA PCM devices
provided by drivers for audio and music units in IEEE 1394 bus were
constrained in the maximum size of buffer period (64 ms in most
cases). This limitation is resolved by dynamically allocating the
header buffer with an arbitrary size.
* tag 'firewire-updates-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
ALSA: firewire: remove PCM buffer size constraint from isoc context header
firewire: core: add fw_iso_context_create() variant with header storage size
firewire: core: provide isoc header buffer size outside card driver
firewire: ohci: allocate isoc context header by kvmalloc()
firewire: core: add flags member for isochronous context structure
firewire: ohci: use cleanup helper for isoc context header allocation
firewire: ohci: code refactoring to use union for isoc multiple channel state
firewire: ohci: refactor isoc single-channel state using a union
firewire: core: add function variants for isochronous context creation
firewire: ohci: fix index of pages for dma address to 1394 OHCI IT context
firewire: ohci: stop using page private to store DMA mapping address
firewire: ohci: split page allocation from dma mapping
firewire: ohci: use MAX macro to guarantee minimum count of pages for AR contexts
firewire: core: stop using page private to store DMA mapping address
firewire: core: use common kernel API to allocate and release a batch of pages
firewire: core: code refactoring with cleanup function for isoc pages
firewire: core: use mutex instead of spinlock for client isochronous context
firewire: core: move private function declaration from public header to internal header
Linus Torvalds [Wed, 11 Feb 2026 19:28:10 +0000 (11:28 -0800)]
Merge tag 'hid-for-linus-2026020901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- global switch of HID drivers to use pm_*ptr instead of #ifdef
CONFIG_PM* (Bastien Nocera)
- support for new firmware handling in intel-ish-hid (Vishnu Sankar)
- support for HID output reports in the Quicki2c in intel-thc (Even Xu)
- solidify register configuration updates in intel-thc (Even Xu)
- Support for Rock band 4 PS4 and PS5 guitars (Rosalie Wanders)
- fn lock and WMI fan control handling improvements in certain Asus
models (ROG, ProArt P16) (Ionut Nechita, Connor Belli)
- fix for potential NULL pointer dereference during warm reset in
intel-ish-hid (Ryan Lin)
- fix for potential NULL pointer derefence in probe error paths in
hid-pl (Oliver Neukum)
- various other small assorted fixes and new device ID additions /
device-specific quirks
* tag 'hid-for-linus-2026020901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (41 commits)
HID: sony: add dongle device IDs for CRKD Gibson SG
HID: Intel-thc-hid: Intel-thc: Fix wrong register fields updating
HID: intel-ish-hid: fix NULL-ptr-deref in ishtp_bus_remove_all_clients
HID: logitech-hidpp: Add support for Logitech K980
HID: logitech-dj: Differentiate "invalid device index" error
HID: sony: Use pm_ptr instead of #ifdef CONFIG_PM
HID: wacom: Use pm_ptr instead of #ifdef CONFIG_PM
HID: uclogic: Use pm_ptr instead of #ifdef CONFIG_PM
HID: hid-sensor-hub: Use pm_ptr instead of #ifdef CONFIG_PM
HID: picolcd_core: Use pm_ptr instead of #ifdef CONFIG_PM
HID: nintendo: Use pm_ptr instead of #ifdef CONFIG_PM
HID: logitech-dj: Use pm_ptr instead of #ifdef CONFIG_PM
HID: lenovo: Use pm_ptr instead of #ifdef CONFIG_PM
HID: asus: Use pm_ptr instead of #ifdef CONFIG_PM
HID: appletb-kbd: Use pm_ptr instead of #ifdef CONFIG_PM
HID: hid-alps: Use pm_ptr instead of #ifdef CONFIG_PM
HID: multitouch: add eGalaxTouch EXC3188 support
HID: elecom: Add support for ELECOM HUGE Plus M-HT1MRBK
HID: sony: add support for bluetooth Rock Band 4 PS4 guitars
HID: logitech-hidpp: Check maxfield in hidpp_get_report_length()
...
Linus Torvalds [Wed, 11 Feb 2026 19:00:19 +0000 (11:00 -0800)]
Merge tag 'hwmon-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New PMBus drivers:
- HiTRON HAC300S power supply
- Monolithic MP5926 Hot-Swap Controller
- STEF48H28 hot-swap controller
Support for new chips in existing drivers
- Support for Pro WS TRX50-SAGE WIFI A and ROG MAXIMUS X HERO
(asus-ec-sensors)
- Support for Dell OptiPlex 7080 (dell-smm)
- Support for F81968 (f71882fg)
- Support for Micro PC 2 (gpd-fan)
- New customer ID for ASRock Z590 Taichi (nct6683)
- Support for ASUS Pro WS WRX90E-SAGE SE (nct6775)
- Support for SHT85 (sht3x)
- Support for P3T1035 and P3T2030 (tmp108)
Bug fixes:
- Revert "fix" for UAF which didn't fix a UAF but introduced a race
condition resulting in a NULL pointer crash (ibmpex)
- Fix failure to instantiate driver if the chip is configured for VID
mode (pmbus/mpq8785)
- Use READ/WRITE_ONCE to avoid compiler optimization induced race
(max16065)
- Resource leak fixes (nct7363, emc2305)
Other notable changes:
- Support for temperature limit thresholds (cros_ec)
- Add TjMax for Silvermont through Tremont Atoms (coretemp)
Various other minor improvements"
* tag 'hwmon-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (42 commits)
hwmon: (pmbus/mpq8785) fix VOUT_MODE mismatch during identification
Revert "hwmon: (ibmpex) fix use-after-free in high/low store"
hwmon: (max16065) Use READ/WRITE_ONCE to avoid compiler optimization induced race
hwmon: (nct6775) use sysfs_emit instead of sprintf
hwmon: pmbus: fix table in STEF48H28 documentation
hwmon: Add support for HiTRON HAC300S PSU
dt-bindings: trivial-devices: Add hitron,hac300s
hwmon: (cros_ec) Add support for temperature thresholds
hwmon: (cros_ec) Move temperature channel params to a macro
hwmon: (cros_ec) Add support for fan target speed
hwmon: (cros_ec) Split up supported features in the documentation
hwmon: (tmp108) Add P3T1035 and P3T2030 support
hwmon: (tmp108) Add support for P3T1035 and P3T2030
dt-bindings: hwmon: ti,tmp108: Add P3T1035,P3T2030
hwmon: pmbus: add support for STEF48H28
dt-bindings: hwmon: add STEF48H28
hwmon: (nct7363) Fix a resource leak in nct7363_present_pwm_fanin
hwmon: (emc2305) Fix a resource leak in emc2305_of_parse_pwm_child
hwmon: (gpd-fan) add support for Micro PC 2
hwmon: (coretemp) Add TjMax for Silvermont through Tremont Atoms
...
Linus Torvalds [Wed, 11 Feb 2026 18:53:39 +0000 (10:53 -0800)]
Merge tag 'gpio-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and some changes to GPIO core but mostly
just GPIO driver updates across a wide array of files, adding support
for new models as well as various refactoring changes. Nothing
controversial and everything has spent a good measure of time in
linux-next.
GPIOLIB core:
- shrink the GPIO bus driver stub code
- rework software node support for "undefined" software nodes
- provide and use devm_fwnode_gpiod_get_optional()
- only compile the OF quirk for MT2701 when needed
New drivers:
- add the GPIO driver for ROHM bd72720
- add the gpio-line-mux driver providing 1-to-many mapping for a
single real GPIO
Driver changes:
- refactor gpio-pca9570: use lock guard, add missing headers, use
devres consistently
- add support for a new model (G7 Aspeed sgpiom) to the aspeed-sgpio
driver along with some prerequisite refactoring
- use device_get_match_data() where applicable and save some lines
- add support for more models to gpio-cadence
- add the compatible property to reset-gpio and use it in shared GPIO
management
- drop unnecessary use of irqd_get_trigger_type() in gpio-max77759
- add support for a new variant to gpio-pca953x
- extend build coverage with COMPILE_TEST for more drivers
- constify configfs structures in gpio-sim and gpio-virtuser
- add support for the K3 SoC to gpio-spacemit
- implement the missing .get_direction() callback in gpio-max77620
- add support for Tegra264 to gpio-tegra186
- drop unneeded MODULE_ALIAS() from gpio-menz127
DT bindings:
- document support for the opencores GPIO controller in gpio-mmio
- document new variants for gpio-pca953x
Documentation:
- extensively describe interrupt source detection for gpio-pca953x
and add more models to the list of supported variants"
* tag 'gpio-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (59 commits)
gpio: tegra186: Add support for Tegra264
dt-bindings: gpio: Add Tegra264 support
gpio: spacemit-k1: Use PDR for pin direction, not SDR/CDR
gpio: max77620: Implement .get_direction() callback
gpio: aspeed-sgpio: Support G7 Aspeed sgpiom controller
dt-bindings: gpio: aspeed,sgpio: Support ast2700
gpio: aspeed-sgpio: Convert IRQ functions to use llops callbacks
gpio: aspeed-sgpio: Create llops to handle hardware access
gpio: aspeed-sgpio: Remove unused bank name field
gpio: aspeed-sgpio: Change the macro to support deferred probe
regulator: bd71815: switch to devm_fwnode_gpiod_get_optional
gpiolib: introduce devm_fwnode_gpiod_get_optional() wrapper
gpio: mmio: Add compatible for opencores GPIO
dt-bindings: gpio-mmio: Correct opencores GPIO
gpio: pca9570: use lock guards
gpio: pca9570: Don't use "proxy" headers
gpio: pca9570: Use devm_mutex_init() for mutex initialization
MAINTAINERS: Add ROHM BD72720 PMIC
power: supply: bd71828-power: Support ROHM BD72720
power: supply: bd71828: Support wider register addresses
...
Linus Torvalds [Wed, 11 Feb 2026 18:45:11 +0000 (10:45 -0800)]
Merge tag 'pwrseq-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
"One new driver and support for more models added to the existing
qcom-wcn driver as well as some minor tweaks and fixes.
New drivers:
- add the power sequencing driver for PCIe M.2 connectors
Driver improvements:
- use device_get_match_data() where applicable
- add support for the WCN39xx family of models to pwrseq-qcom-wcn
Fixes:
- fix a locking issue in pwrseq core
- fix retval check in pwrseq-qcom-wcn"
* tag 'pwrseq-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: fix error path for VDDIO handling
power: sequencing: fix missing state_lock in pwrseq_power_on() error path
power: sequencing: Add the Power Sequencing driver for the PCIe M.2 connectors
dt-bindings: connector: Add PCIe M.2 Mechanical Key M connector
power: sequencing: qcom-wcn: add support for WCN39xx
regulator: dt-bindings: qcom,wcn3990-pmu: describe PMUs on WCN39xx
power: sequencing: qcom-wcn: use device_get_match_data()
Linus Torvalds [Wed, 11 Feb 2026 17:52:33 +0000 (09:52 -0800)]
Merge tag 'pwm/for-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"There are a few patches adapting to changes in Rust land which seems
to be the norm since there is a pwm driver written in Rust. Other than
that just a few cleanups and a single fix for the tiehrpwm driver that
came in too late for making it into v6.19.
Thanks to Andy Shevchenko, Bartosz Golaszewski, Daniel Almeida and
Michal Wilczynski for reviews in this cycle, and to Alice Ryhl, Ben
Zong-You Xie, Gokul Praveen, Kari Argillander, Markus Probst, Raag
Jadav, Shankari Anand, Tamir Duberstein and Vladimir Zapolskiy for
code contributions"
* tag 'pwm/for-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: Remove redundant check in pwm_ops_check()
pwm: tiehrpwm: Enable pwmchip's parent device before setting configuration
pwm: Update MAINTAINER entry
rust: pwm: Add __rust_helper to helpers
rust: pwm: Simplify to_result call sites and unsafe blocks
rust: pwm: Fix potential memory leak on init error
dt-bindings: pwm: nxp,lpc32xx-pwm: Specify clocks property as mandatory
pwm: th1520: Replace `kernel::c_str!` with C-Strings
pwm: dwc: Use size macro
pwm: Emit native configuration in /sys/kernel/debug/pwm
rust: pwm: Add UnregisteredChip wrapper around Chip
rust: pwm: Update ARef and AlwaysRefCounted imports to use sync::aref
Linus Torvalds [Wed, 11 Feb 2026 17:43:43 +0000 (09:43 -0800)]
Merge tag 'spi-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The highlight here is that David Lechner has added support for
multi-lane SPI devices. Unlike the existing dual/quad SPI support this
is for devices (typically ADCs/DACs) which support multiple
independent data streams over multiple data lanes, instead of sending
one data stream N times as fast they simultaneously transfer N
different data streams.
This is very similar to the case where multiple devices are grouped
together but in this case it's a single device in a way that's visible
to software.
Otherwise there's been quite a bit of work on existing drivers, both
cleanup and feature improvement, and a reasonable collection of new
drivers.
- Support for multi-lane SPI devices
- Preparatory work for some memory mapped flash improvements that
will happen in the MTD subsystem
- Several conversions to fwnode APIs
- A bunch of cleanup and hardening work on the ST drivers
- Support for DMA mode on Renesas RZV2H and i.MX target mode
- Support for ATCSPI200, AXIADO AX300, NXP XPI and Renesas RZ/N1"
* tag 'spi-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (108 commits)
spi: tools: Add include folder to .gitignore
spi: cadence-qspi: Add support for the Renesas RZ/N1 controller
spi: cadence-qspi: Kill cqspi_jh7110_clk_init
spi: dt-bindings: cdns,qspi-nor: Add Renesas RZ/N1D400 to the list
spi: geni-qcom: Add target abort support
spi: geni-qcom: Drop unused msg parameter from timeout handlers
spi: geni-qcom: Fix abort sequence execution for serial engine errors
spi: geni-qcom: Improve target mode allocation by using proper allocation functions
spi: xilinx: use device property accessors.
dt-bindings: spi: Add binding for Faraday FTSSP010
spi: axi-spi-engine: support SPI_MULTI_LANE_MODE_STRIPE
spi: dt-bindings: adi,axi-spi-engine: add multi-lane support
spi: Documentation: add page on multi-lane support
spi: add multi_lane_mode field to struct spi_transfer
spi: support controllers with multiple data lanes
spi: dt-bindings: add spi-{tx,rx}-lane-map properties
spi: dt-bindings: change spi-{rx,tx}-bus-width to arrays
spi: dw: Remove not-going-to-be-supported code for Baikal SoC
spi: cadence-qspi: Use a default value for cdns,fifo-width
spi: cadence-qspi: Make sure write protection is disabled
...
Linus Torvalds [Wed, 11 Feb 2026 17:40:12 +0000 (09:40 -0800)]
Merge tag 'regulator-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"There's a bunch of new drivers here, plus a lot of hardening for the
supply resolution code which allow us to support systems where we have
two PMICs each of which has regulators supplied by the other. This did
work a long time ago but got broken as part of improved integration
with the device model, it's fairly rare so nobody noticed.
- Improvements for supply handling from André Draszik to allow
systems with two PMICs with supply/consumer relationships in both
directions to instantiate.
- New drivers for Maxim MAX776750, Realtek RT8902, Samsung S2MPG11,
Texas Instuments TPS65185.
This have also pulls in some MFD updates which are build dependencies
for the Samsung S2MPG11 support"
* tag 'regulator-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (42 commits)
regulator: s2mps11: more descriptive gpio consumer name
regulator: s2mps11: add S2MPG11 regulator
regulator: s2mps11: refactor S2MPG10 regulator macros for S2MPG11 reuse
regulator: s2mps11: refactor S2MPG10 ::set_voltage_time() for S2MPG11 reuse
regulator: s2mps11: add S2MPG10 regulator
regulator: s2mps11: refactor handling of external rail control
regulator: s2mps11: update node parsing (allow -supply properties)
regulator: s2mps11: place constants on right side of comparison tests
regulator: s2mps11: use dev_err_probe() where appropriate
regulator: s2mps11: drop two needless variable initialisations
regulator: add REGULATOR_LINEAR_VRANGE macro
regulator: dt-bindings: add s2mpg11-pmic regulators
regulator: dt-bindings: add s2mpg10-pmic regulators
dt-bindings: firmware: google,gs101-acpm-ipc: convert regulators to lowercase
mfd: sec: Add support for S2MPG11 PMIC via ACPM
mfd: sec: s2mpg10: Reorder regulators for better probe performance
dt-bindings: mfd: Add samsung,s2mpg11-pmic
dt-bindings: mfd: samsung,s2mpg10-pmic: Link to its regulators
dt-bindings: mfd: samsung,s2mps11: Split s2mpg10-pmic into separate file
mfd: sec: Drop now unused struct sec_pmic_dev::irq_data
...
Linus Torvalds [Wed, 11 Feb 2026 17:23:13 +0000 (09:23 -0800)]
Merge tag 'regmap-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"The main change here is the implementation of a mechanism for
generating register defaults via a callback rather than with a table
in the driver.
This is useful for devices where there are large ranges of registers
with the same or generated values, it allows us to have a small amount
of code instead of a larger amount of default data"
* tag 'regmap-v6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regcache: Demote defaults readback from HW to debug print
regmap: add KUnit coverage for reg_default_cb callback
regmap: Add reg_default_cb callback for flat cache defaults
regmap: Enable REGMAP when REGMAP_SLIMBUS is enabled
Linus Torvalds [Wed, 11 Feb 2026 17:19:47 +0000 (09:19 -0800)]
Merge tag 'chrome-platform-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Tzung-Bi Shih:
"New cros_ec_lightbar features:
- Report the number of exposed LED segments via sysfs
- Support large sequence of program to be transmitted
Fixes:
- Don't touch fwnode_handle::dev which is a private field
- Fix wrong assignment for response size in cros_ec_lightbar
Cleanups:
- Use acpi_get_local_u64_address() helper"
* tag 'chrome-platform-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: lightbar: Use flexible array member
platform/chrome: lightbar: Fix lightbar_program_ex alignment
platform/chrome: lightbar: Add support for large sequence
platform/chrome: lightbar: Report number of segments
platform/chrome: cros_ec_lightbar: Fix response size initialization
platform/chrome: cros_typec_switch: Use acpi_get_local_u64_address()
platform/chrome: cros_typec_switch: Don't touch struct fwnode_handle::dev
Vikas Gupta [Sun, 8 Feb 2026 17:29:25 +0000 (22:59 +0530)]
bnge/bng_re: Add a new HSI
The HSI is shared between the firmware and the driver and is
automatically generated.
Add a new HSI for the BNGE driver. The current HSI refers to BNXT,
which will become incompatible with ThorUltra devices as the
BNGE driver adds more features. The BNGE driver will not use the HSI
located in the bnxt folder.
Also, add an HSI for ThorUltra RoCE driver.
Changes in v3:
- Fix in bng_roce_hsi.h reported by Jakub (AI review)
https://lore.kernel.org/netdev/20260207051422.4181717-1-kuba@kernel.org/
- Add an entry in MAINTAINERS
Kevin Hao [Sun, 8 Feb 2026 08:45:52 +0000 (16:45 +0800)]
net: macb: Fix tx/rx malfunction after phy link down and up
In commit 99537d5c476c ("net: macb: Relocate mog_init_rings() callback
from macb_mac_link_up() to macb_open()"), the mog_init_rings() callback
was moved from macb_mac_link_up() to macb_open() to resolve a deadlock
issue. However, this change introduced a tx/rx malfunction following
phy link down and up events. The issue arises from a mismatch between
the software queue->tx_head, queue->tx_tail, queue->rx_prepared_head,
and queue->rx_tail values and the hardware's internal tx/rx queue
pointers.
According to the Zynq UltraScale TRM [1], when tx/rx is disabled, the
internal tx queue pointer resets to the value in the tx queue base
address register, while the internal rx queue pointer remains unchanged.
The following is quoted from the Zynq UltraScale TRM:
When transmit is disabled, with bit [3] of the network control register
set low, the transmit-buffer queue pointer resets to point to the address
indicated by the transmit-buffer queue base address register. Disabling
receive does not have the same effect on the receive-buffer queue
pointer.
Additionally, there is no need to reset the RBQP and TBQP registers in a
phy event callback. Therefore, move macb_init_buffers() to macb_open().
In a phy link up event, the only required action is to reset the tx
software head and tail pointers to align with the hardware's behavior.
Kevin Hao [Sat, 7 Feb 2026 06:21:46 +0000 (14:21 +0800)]
net: ti: icssg-prueth: Add optional dependency on HSR
Commit 95540ad6747c ("net: ti: icssg-prueth: Add support for HSR frame
forward offload") introduced support for offloading HSR frame forwarding,
which relies on functions such as is_hsr_master() provided by the HSR
module. Although HSR provides stubs for configurations with HSR
disabled, this driver still requires an optional dependency on HSR.
Otherwise, build failures will occur when icssg-prueth is built-in
while HSR is configured as a module.
ld.lld: error: undefined symbol: is_hsr_master
>>> referenced by icssg_prueth.c:710 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:710)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:681 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:681)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_add_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:1812 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:1812)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(prueth_netdevice_event) in archive vmlinux.a
ld.lld: error: undefined symbol: hsr_get_port_ndev
>>> referenced by icssg_prueth.c:712 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:712)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:712 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:712)
>>> drivers/net/etherneteth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:683 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:683)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_add_mcast) in archive vmlinux.a
>>> referenced 1 more times
Fixes: 95540ad6747c ("net: ti: icssg-prueth: Add support for HSR frame forward offload") Signed-off-by: Kevin Hao <haokexin@gmail.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20260207-icssg-dep-v3-1-8c47c1937f81@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
net: dsa: initial support for MaxLinear MxL862xx switches
This series adds very basic DSA support for the MaxLinear MxL86252
(5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches.
In addition to the 2.5G TP ports both switches also come with two
SerDes interfaces which can be used either to connect external PHYs
or SFP cages, or as CPU port when using the switch with this DSA driver.
MxL862xx integrates a firmware running on an embedded processor (based on
Zephyr RTOS). Host interaction uses a simple netlink-like API transported
over MDIO/MMD.
This series includes only what's needed to pass traffic between user
ports and the CPU port: relayed MDIO to internal PHYs, basic port
enable/disable, and CPU-port special tagging.
The SerDes interface of the CPU port is automatically configured by the
switch after reset using a board-specific configuration stored together
with the firmware in the flash chip attached to the switch, so no action
is needed from the driver to setup the interface mode of the CPU port.
Also MAC settings of the PHY ports are automatically configured, which
means the driver works fine with phylink_mac_ops being all no-op stubs.
Multiple follow up series will bring support for setting up the other
SerDes PCS interface (ie. not used for the CPU port), bridge, VLAN, ...
offloading, and support for using an 802.1Q-based special tag instead of
the proprietary 8-byte tag.
====================
Daniel Golle [Sat, 7 Feb 2026 03:07:27 +0000 (03:07 +0000)]
net: dsa: add basic initial driver for MxL862xx switches
Add very basic DSA driver for MaxLinear's MxL862xx switches.
In contrast to previous MaxLinear switches the MxL862xx has a built-in
processor that runs a sophisticated firmware based on Zephyr RTOS.
Interaction between the host and the switch hence is organized using a
software API of that firmware rather than accessing hardware registers
directly.
Add descriptions of the most basic firmware API calls to access the
built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as
setting up the CPU port.
Implement a very basic DSA driver using that API which is sufficient to
get packets flowing between the user ports and the CPU port.
The firmware offers all features one would expect from a modern switch
hardware, they are going to be added one by one in follow-up patch
series.
Daniel Golle [Sat, 7 Feb 2026 03:07:18 +0000 (03:07 +0000)]
net: mdio: add unlocked mdiodev C45 bus accessors
Add helper inline functions __mdiodev_c45_read() and
__mdiodev_c45_write(), which are the C45 equivalents of the existing
__mdiodev_read() and __mdiodev_write() added by commit e6a45700e7e1
("net: mdio: add unlocked mdiobus and mdiodev bus accessors")
Daniel Golle [Sat, 7 Feb 2026 03:07:11 +0000 (03:07 +0000)]
net: dsa: add tag format for MxL862xx switches
Add proprietary special tag format for the MaxLinear MXL862xx family of
switches. While using the same Ethertype as MaxLinear's GSW1xx switches,
the actual tag format differs significantly, hence we need a dedicated
tag driver for that.
projects / thirdparty / kernel / linux.git / log
