v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is
invalid or if the user is trying to use a multiplanar format with the
singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such
value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns
an error value if vimc_cap_try_fmt_vid_cap() has failed.
Signed-off-by: André Almeida <andrealmeid@collabora.com> Suggested-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message] Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some Qualcomm Snapdragon based laptops built to run Microsoft Windows
are clearly ACPI 5.1 based, given that that is the first ACPI revision
that supports ARM, and introduced the FADT 'arm_boot_flags' field,
which has a non-zero field on those systems.
So in these cases, infer from the ARM boot flags that the FADT must be
5.1 or later, and treat it as 5.1.
Don't allow the TAI-UTC offset of the system clock to be set by adjtimex()
to a value larger than 100000 seconds.
This prevents an overflow in the conversion to int, prevents the CLOCK_TAI
clock from getting too far ahead of the CLOCK_REALTIME clock, and it is
still large enough to allow leap seconds to be inserted at the maximum rate
currently supported by the kernel (once per day) for the next ~270 years,
however unlikely it is that someone can survive a catastrophic event which
slowed down the rotation of the Earth so much.
Reported-by: Weikang shi <swkhack@gmail.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190618154713.20929-1-mlichvar@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the beginning the second clock ('special', 'sclk') was optional and
it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with
v7 of MFC hardware).
However commit 1bce6fb3edf1 ("[media] s5p-mfc: Rework clock handling")
made handling of all specified clocks mandatory. This patch restores
original behavior of the driver and fixes its operation on
Exynos5420 SoCs.
syzkaller reports for memory leak when registering hooks [1]
As we moved the nf_unregister_net_hooks() call into
__ip_vs_dev_cleanup(), defer the nf_register_net_hooks()
call, so that hooks are allocated and freed from same
pernet_operations (ipvs_core_dev_ops).
kernelci.org reports failed builds on arc because of what looks
like an old missed 'select' statement:
net/xfrm/xfrm_algo.o: In function `xfrm_probe_algs':
xfrm_algo.c:(.text+0x1e8): undefined reference to `crypto_has_ahash'
I don't see this in randconfig builds on other architectures, but
it's fairly clear we want to select the hash code for it, like we
do for all its other users. As Herbert points out, CRYPTO_BLKCIPHER
is also required even though it has not popped up in build tests.
Fixes: 17bc19702221 ("ipsec: Use skcipher and ahash when probing algorithms") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In edac_create_csrow_object(), the reference to the object is not
released when adding the device to the device hierarchy fails
(device_add()). This may result in a memory leak.
Vhost_net was known to suffer from HOL[1] issues which is not easy to
fix. Several downstream disable the feature by default. What's more,
the datapath was split and datacopy path got the support of batching
and XDP support recently which makes it faster than zerocopy part for
small packets transmission.
It looks to me that disable zerocopy by default is more
appropriate. It cold be enabled by default again in the future if we
fix the above issues.
Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In which case it simply returns "unknown", like when it can't figure out
the evsel->name value.
This makes this code more robust and fixes a problem in 'perf trace'
where a NULL evsel was being passed to a routine that only used the
evsel for printing its name when a invalid syscall id was passed.
Reported-by: Leo Yan <leo.yan@linaro.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-f30ztaasku3z935cn3ak3h53@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:
Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:
After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4
In fact, the selector is not mandatory, allow the user to provide an empty
selector.
Fixes: b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation") CC: Anirudh Gupta <anirudh.gupta@sophos.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
wbc_account_io() collects information on cgroup ownership of writeback
pages to determine which cgroup should own the inode. Pages can stay
associated with dead memcgs but we want to avoid attributing IOs to
dead blkcgs as much as possible as the association is likely to be
stale. However, currently, pages associated with dead memcgs
contribute to the accounting delaying and/or confusing the
arbitration.
Fix it by ignoring pages associated with dead memcgs.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the CPUID enumeration for Intel's de-feature bits to accommodate
passing these de-features through to kvm guests.
These de-features are (from SDM vol 1, section 8.1.8):
- X86_FEATURE_FDP_EXCPTN_ONLY: If CPUID.(EAX=07H,ECX=0H):EBX[bit 6] = 1, the
data pointer (FDP) is updated only for the x87 non-control instructions that
incur unmasked x87 exceptions.
- X86_FEATURE_ZERO_FCS_FDS: If CPUID.(EAX=07H,ECX=0H):EBX[bit 13] = 1, the
processor deprecates FCS and FDS; it saves each as 0000H.
Signed-off-by: Aaron Lewis <aaronlewis@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: marcorr@google.com Cc: Peter Feiner <pfeiner@google.com> Cc: pshier@google.com Cc: Robert Hoo <robert.hu@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Lendacky <Thomas.Lendacky@amd.com> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190605220252.103406-1-aaronlewis@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When debugging options are turned on, the rcu_read_lock() function
might not be inlined. This results in lockdep's print_lock() function
printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller.
For example:
[ 10.579995] =============================
[ 10.584033] WARNING: suspicious RCU usage
[ 10.588074] 4.18.0.memcg_v2+ #1 Not tainted
[ 10.593162] -----------------------------
[ 10.597203] include/linux/rcupdate.h:281 Illegal context switch in
RCU read-side critical section!
[ 10.606220]
[ 10.606220] other info that might help us debug this:
[ 10.606220]
[ 10.614280]
[ 10.614280] rcu_scheduler_active = 2, debug_locks = 1
[ 10.620853] 3 locks held by systemd/1:
[ 10.624632] #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70
[ 10.633232] #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
[ 10.640954] #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
These "rcu_read_lock+0x0/0x70" strings are not providing any useful
information. This commit therefore forces inlining of the rcu_read_lock()
function so that rcu_read_lock()'s caller is instead shown.
Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:
kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~
kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~
98 copies of the above.
The attached patch silences the warnings, because we *know* we're overwriting
the default initializer. That leaves bpf/core.c with only 6 other warnings,
which become more visible in comparison.
On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NOTE: There must be a correlation between the wake-up enable and
interrupt-enable registers. If a GPIO pin has a wake-up configured
on it, it must also have the corresponding interrupt enabled (on
one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt. This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and
trigger setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.
This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.
Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case we expand an existing region, we unlink
this latter and insert the larger one. In
that case we should free the original region after
the insertion. Also we can immediately return.
New Gen3 R-Car platforms incorporate the FDP1 with an updated version
register. No code change is required to support these targets, but they
will currently report an error stating that the device can not be
identified.
Update the driver to match against the new device types.
when the kvm module is not loaded or not built in.
Fix this by adding a valid function which tests if the module
is loaded. Loaded modules (or builtin KVM support) have a
directory named
/sys/kernel/debug/tracing/events/kvm-s390
for this tracepoint.
Check for existence of this directory.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20190604053504.43073-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds the necessary intelligence to properly compute the value
of 'old' and 'head' when operating in snapshot mode. That way we can
get the latest information in the AUX buffer and be compatible with the
generic AUX ring buffer mechanic.
Tester notes:
> Leo, have you had the chance to test/review this one? Suzuki?
Sure. I applied this patch on the perf/core branch (with latest
commit 3e4fbf36c1e3 'perf augmented_raw_syscalls: Move reading
filename to the loop') and passed testing with below steps:
# perf record -e cs_etm/@tmc_etr0/ -S -m,64 --per-thread ./sort &
[1] 19097
Bubble sorting array of 30000 elements
# kill -USR2 19097
# kill -USR2 19097
# kill -USR2 19097
[ perf record: Woken up 4 times to write data ]
[ perf record: Captured and wrote 0.753 MB perf.data ]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/20190605161633.12245-1-mathieu.poirier@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a fresh array block is allocated during resize, the current in-memory
set size should be increased by the size of the block, not replaced by it.
Before the fix, adding entries to a hash set type, leading to a table
resize, caused an inconsistent memory size to be reported. This becomes
more obvious when swapping sets with similar sizes:
# cat hash_ip_size.sh
#!/bin/sh
FAIL_RETRIES=10
tries=0
while [ ${tries} -lt ${FAIL_RETRIES} ]; do
ipset create t1 hash:ip
for i in `seq 1 4345`; do
ipset add t1 1.2.$((i / 255)).$((i % 255))
done
t1_init="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset create t2 hash:ip
for i in `seq 1 4360`; do
ipset add t2 1.2.$((i / 255)).$((i % 255))
done
t2_init="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset swap t1 t2
t1_swap="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
t2_swap="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When inserting random PFNs for debugging the CEC through
(debugfs)/ras/cec/pfn, depending on the return value of pfn_set(),
multiple values get inserted per a single write.
That is because simple_attr_write() interprets a retval of 0 as
success and claims the whole input. However, pfn_set() returns the
cec_add_elem() value, which, if > 0 and smaller than the whole input
length, makes glibc continue issuing the write syscall until there's
input left:
When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.
This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support") Signed-off-by: Biao Huang <biao.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To set frequency on specific cpus using cpupower, following syntax can
be used :
cpupower -c #i frequency-set -f #f -r
While setting frequency using cpupower frequency-set command, if we use
'-r' option, it is expected to set frequency for all cpus related to
cpu #i. But it is observed to be missing the last cpu in related cpu
list. This patch fixes the problem.
X-Originating-IP: [10.175.113.25]
X-CFilter-Loop: Reflected
The fm_v4l2_init_video_device() forget to unregister v4l2/video device
in the error path, it could lead to UAF issue, eg,
BUG: KASAN: use-after-free in atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline]
BUG: KASAN: use-after-free in atomic_long_read include/asm-generic/atomic-long.h:28 [inline]
BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206
Read of size 8 at addr ffff8881e84a7c70 by task v4l_id/3659
will trigger the following error in __lock_release() when calling
mutex_release() at **:
DEBUG_LOCKS_WARN_ON(depth <= 0)
The problem is that the hlock merging happening at * updates the
references for test_ww_class incorrectly to 3 whereas it should've
updated it to 4 (representing all the instances for ww_ctx and
ww_lock_[abc]).
Fix this by updating the references during merging correctly taking into
account that we can have non-zero references (both for the hlock that we
merge into another hlock or for the hlock we are merging into).
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= <ville.syrjala@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/r/20190524201509.9199-2-imre.deak@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rename _P to _P_VAL and _R to _R_VAL to avoid global
namespace conflicts:
drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:
drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
#define _P 32
In file included from ./include/acpi/platform/aclinux.h:54,
from ./include/acpi/platform/acenv.h:152,
from ./include/acpi/acpi.h:22,
from ./include/linux/acpi.h:34,
from ./include/linux/i2c.h:17,
from drivers/media/dvb-frontends/tua6100.h:30,
from drivers/media/dvb-frontends/tua6100.c:32:
./include/linux/ctype.h:14: note: this is the location of the previous definition
#define _P 0x10 /* punct */
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
SEC Lite-initiated 8xx writes can occur only on 32-bit-word boundaries, but
reads can occur on any byte boundary. Writing back a header read from a
non-32-bit-word boundary will yield unpredictable results.
In order to ensure that, cra_alignmask is set to 3 for SEC1.
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to avoid possible memory leak if the decoder initialization
got failed.Free the allocated memory for file handle object
before return in case decoder initialization fails.
Replace some BUG_ON()s with WARN_ON_ONCE() and returning an error code,
and move the check for len divisible by FS_CRYPTO_BLOCK_SIZE into
fscrypt_crypt_block() so that it's done for both encryption and
decryption, not just encryption.
Family of src/dst can be different from family of selector src/dst.
Use xfrm selector family to validate address prefix length,
while verifying new sa from userspace.
Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \
0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5
Fixes: 07bf7908950a ("xfrm: Validate address prefix lengths in the xfrm selector.") Signed-off-by: Anirudh Gupta <anirudh.gupta@sophos.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The locking in force_sig_info is not prepared to deal with a task that
exits or execs (as sighand may change). The is not a locking problem
in force_sig as force_sig is only built to handle synchronous
exceptions.
Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal. The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.
So using force_sig rather than send_sig for SIGKILL is confusing
and pointless.
Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.
Cc: Daniel Lezcano <daniel.lezcano@free.fr> Cc: Serge Hallyn <serge@hallyn.com> Cc: Oleg Nesterov <oleg@redhat.com> Fixes: cf3f89214ef6 ("pidns: add reboot_pid_ns() to handle the reboot syscall") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 100g mode the doorbell bar is united for both engines. Set
the correct offset in the hwfn so that the doorbell returned
for RoCE is in the affined hwfn.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com> Signed-off-by: Denis Bolotin <denis.bolotin@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
[ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.043185] 00000000: fe dc ba 98 76 54 32 10
[ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42
This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.
A handler for BATADV_TVLV_ROAM was being registered when the
translation-table was initialized, but not unregistered when the
translation-table was freed. Unregister it.
Fixes: 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets") Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.
The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements. We need to add a couple bounds
checks to prevent array overflows.
I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.
Fixes: bdcd81707973 (" Add ath6kl cleaned up driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: Tim Schumacher <timschumi@gmx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If probe() fails anywhere beyond the point where
sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the
firmware callback to run when firmware becomes available,
using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the
sdma instance structure
3. firmware becomes available, firmware callback is
called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain
that probe() will succeed. This guarantees that the firmware
callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the
firmware loader will increment the driver module's use count,
ensuring that the module cannot be unloaded while the
firmware callback is pending or running.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Reviewed-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: fixed braces for if condition] Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
After r363059 and r363928 in LLVM, a build using ld.lld as the linker
with CONFIG_RANDOMIZE_BASE enabled fails like so:
ld.lld: error: relocation R_AARCH64_ABS32 cannot be used against symbol
__efistub_stext_offset; recompile with -fPIC
Fangrui and Peter figured out that ld.lld is incorrectly considering
__efistub_stext_offset as a relative symbol because of the order in
which symbols are evaluated. _text is treated as an absolute symbol
and stext is a relative symbol, making __efistub_stext_offset a
relative symbol.
Adding ABSOLUTE will force ld.lld to evalute this expression in the
right context and does not change ld.bfd's behavior. ld.lld will
need to be fixed but the developers do not see a quick or simple fix
without some research (see the linked issue for further explanation).
Add this simple workaround so that ld.lld can continue to link kernels.
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Suggested-by: Jo-Philipp Wich <jo@mein.io> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
While trying to get the uart with parity working I found setting even
parity enabled odd parity insted. Fix the register settings to match
the datasheet of AR9331.
This should help with some of the lifetime issues, and move us away
from load/unload.
[rez] Regarding the backport to v4.14.y, the only difference is due to
the fact that in v4.14.y the udl_usb_probe() function still uses
drm_dev_unref() instead of drm_dev_put().
Backport notes:
On Mon, Jul 15, 2019 at 09:13:08PM -0400, Sasha Levin wrote:
> Hm, we don't need ac3b35f11a06 here? Why not? I'd love to document that
> with the backport.
Nope, we don't need that patch in the v4.14 backport.
In v4.19.y we have two functions, drm_dev_put() and drm_dev_unref(), which are
aliases for one another (drm_dev_unref() just calls drm_dev_put()).
drm_dev_unref() is the older of the two, and was introduced back in v4.0.
drm_dev_put() was introduced in v4.15 with
and slowly callers were moved from the old name (_unref) to the new name
(_put). The patch you mentioned, ac3b35f11a06, is one such patch where we are
replacing a drm_dev_unref() call with a drm_dev_put() call. This doesn't have
a functional change, but was necessary so that the third patch in the v4.19.y
series I sent would apply cleanly.
For the v4.14.y series, though, the drm_dev_put() function hasn't yet been
defined and everyone is still using drm_dev_unref(). So, we don't need a
backport of ac3b35f11a06, and I also had a small backport change in the last
patch of the v4.14.y series where I had to change a drm_dev_put() call with a
drm_dev_unref() call.
Just for posterity, the drm_dev_unref() calls were eventually all changed to
drm_dev_put() in v5.0, and drm_dev_unref() was removed entirely. That
happened with the following two patches:
808bad32ea423 drm: replace "drm_dev_unref" function with "drm_dev_put" ba1d345401476 drm: remove deprecated "drm_dev_unref" function
This just makes it easier to later embed drm into udl.
[rez] Regarding the backport to v4.14.y, the only difference is due to
the fact that in v4.14.y the udl_gem_mmap() function doesn't have a
local 'struct udl_device' pointer so it didn't need to be converted.
System gets checkstop if RxFIFO overruns with more requests than the
maximum possible number of CRBs in FIFO at the same time. The max number
of requests per window is controlled by window credits. So find max
CRBs from FIFO size and set it to receive window credits.
Fixes: b0d6c9bab5e4 ("crypto/nx: Add P9 NX support for 842 compression engine") CC: stable@vger.kernel.org # v4.14+
Signed-off-by:Haren Myneni <haren@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89fff ("[S390] qdio: set correct bit in dsci") Cc: <stable@vger.kernel.org> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468f7 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
The stfle inline assembly returns the number of double words written
(condition code 0) or the double words it would have written
(condition code 3), if the memory array it got as parameter would have
been large enough.
The current stfle implementation assumes that the array is always
large enough and clears those parts of the array that have not been
written to with a subsequent memset call.
If however the array is not large enough memset will get a negative
length parameter, which means that memset clears memory until it gets
an exception and the kernel crashes.
To fix this simply limit the maximum length. Move also the inline
assembly to an extra function to avoid clobbering of register 0, which
might happen because of the added min_t invocation together with code
instrumentation.
The bug was introduced with commit 14375bc4eb8d ("[S390] cleanup
facility list handling") but was rather harmless, since it would only
write to a rather large array. It became a potential problem with
commit 3ab121ab1866 ("[S390] kernel: Add z/VM LGR detection"). Since
then it writes to an array with only four double words, while some
machines already deliver three double words. As soon as machines have
a facility bit within the fifth double a crash on IPL would happen.
DIV_ROUND_UP_ULL adds the two arguments and then invokes
DIV_ROUND_DOWN_ULL. But on a 32bit system the addition of two 32 bit
values can overflow. DIV_ROUND_DOWN_ULL does it correctly and stashes
the addition into a unsigned long long so cast the result to unsigned
long long here to avoid the overflow condition.
[akpm@linux-foundation.org: DIV_ROUND_UP_ULL must be an rval] Link: http://lkml.kernel.org/r/20190625100518.30753-1-vkoul@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting invalid value to /sys/devices/system/cpu/cpuX/hotplug/fail
can control `struct cpuhp_step *sp` address, results in the following
global-out-of-bounds read.
The buggy address belongs to the variable:
cpu_hotplug_lock+0x98/0xa0
Memory state around the buggy address: ffffffff89734300: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734380: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
>ffffffff89734400: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
^ ffffffff89734480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Add a sanity check for the value written from user space.
A kernel which boots in 5-level paging mode crashes in a small percentage
of cases if KASLR is enabled.
This issue was tracked down to the case when the kernel image unpacks in a
way that it crosses an 1G boundary. The crash is caused by an overrun of
the PMD page table in __startup_64() and corruption of P4D page table
allocated next to it. This particular issue is not visible with 4-level
paging as P4D page tables are not used.
But the P4D and the PUD calculation have similar problems.
The PMD index calculation is wrong due to operator precedence, which fails
to confine the PMDs in the PMD array on wrap around.
The P4D calculation for 5-level paging and the PUD calculation calculate
the first index correctly, but then blindly increment it which causes the
same issue when a kernel image is located across a 512G and for 5-level
paging across a 46T boundary.
This wrap around mishandling was introduced when these parts moved from
assembly to C.
Restore it to the correct behaviour.
Fixes: c88d71508e36 ("x86/boot/64: Rewrite startup_64() in C") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190620112345.28833-1-kirill.shutemov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 605ad7f184b60cfaacbc038aa6c55ee68dee3c89 "tcp: refine TSO autosizing",
outbound throughput is dramatically reduced for some connections, as sis900
is doing TX completion within idle states only.
Make TX completion happen after every transmitted packet.
Test:
netperf
before patch:
> netperf -H remote -l -2000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 253.44 0.06
after patch:
> netperf -H remote -l -10000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 5.38 14.89
Thx to Dave Miller and Eric Dumazet for helpful hints
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a
softdep line, so that the corresponding module gets prepared
gracefully. Without this, a simple inclusion to initrd via dracut
failed due to the missing dependency, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.
Changes in v2:
- added fixes header
Fixes: 4276e47e2d1c ("be2net: Add link test to list of ethtool self tests.") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so
we get a warning with clang-8:
WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup()
The function omap3xxx_prm_late_init() references
the function __init omap3xxx_prm_enable_io_wakeup().
This is often because omap3xxx_prm_late_init lacks a __init
annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong.
When building with gcc, omap3xxx_prm_enable_io_wakeup() is always
inlined, so we never noticed in the past.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_sample_regs_user() uses 'current->mm' to test for the presence of
userspace, but this is insufficient, consider use_mm().
A better test is: '!(current->flags & PF_KTHREAD)', exec() clears
PF_KTHREAD after it sets the new ->mm but before it drops to userspace
for the first time.
Possibly obsoletes: bf05fc25f268 ("powerpc/perf: Fix oops when kthread execs user process")
Reported-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Reported-by: Young Xiao <92siuyang@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4018994f3d87 ("perf: Add ability to attach user level registers dump to sample") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting with ACPI 6.2 bits 1 and 2 of the BGRT status field are no longer
reserved. These bits are now used to indicate if the image needs to be
rotated before being displayed.
The first device using these bits has now shown up (the GPD MicroPC) and
the reserved bits check causes us to reject the valid BGRT table on this
device.
Rather then changing the reserved bits check, allowing only the 2 new bits,
instead just completely remove it so that we do not end up with a similar
problem when more bits are added in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we do a clk_get() for a clock that does not exists, we have
_ti_omap4_clkctrl_xlate() return uninitialized data if no match
is found. This can be seen in some cases with SLAB_DEBUG enabled:
Unable to handle kernel paging request at virtual address 5a5a5a5a
...
clk_hw_create_clk.part.33
sysc_notifier_call
notifier_call_chain
blocking_notifier_call_chain
device_add
Let's fix this by setting a found flag only when we find a match.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Fixes: 88a172526c32 ("clk: ti: add support for clkctrl clocks") Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This check might otherwise be useful to stop users from using a non-linux
compiler, but if you're doing that you are going to have a lot more
trouble anyway.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21149/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VMCI handle array has an integer overflow in
vmci_handle_arr_append_entry when it tries to expand the array. This can be
triggered from a guest, since the doorbell link hypercall doesn't impose a
limit on the number of doorbell handles that a VM can create in the
hypervisor, and these handles are stored in a handle array.
In this change, we introduce a mandatory max capacity for handle
arrays/lists to avoid excessive memory usage.
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzkallar found a 32-byte memory leak in a rarely executed error
case. The transaction complete work item was not freed if put_user()
failed when writing the BR_TRANSACTION_COMPLETE to the user command
buffer. Fixed by freeing it before put_user() is called.
The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card. There is no analog output subdevice for
a PCI260. The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260. The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.
Fixes: 39064f23284c ("staging: comedi: amplc_pci230: use comedi_handle_events()") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support. For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`. In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers. Trust that
they are reliable for now.)
Note:
commit 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4cfe ("staging: comedi: dt282x: use cfc_handle_events()").
Fixes: 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old commit 6e4b74e4690d ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf3888d ("usb: renesas_usbhs: add support for USB-DMAC") Cc: <stable@vger.kernel.org> # v4.1+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Fixes: 2e9fe5391083 ("serial: 8250: Don't service RX FIFO if interrupts are disabled") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
