Trackpoint buttons detection fails on ThinkPad 570 and 470 series,
this makes the middle button of the trackpoint to not being recogized.
As I don't believe there is any trackpoint with less than 3 buttons this
patch just assumes three buttons when the extended button information
read fails.
Signed-off-by: Oscar Campos <oscar.campos@member.fsf.org> Acked-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global spinlock `l3_remap_lock` is reinitialized every time the
"probe" function `alt_fpga_bridge_probe()` is called. It should only be
initialized once. Use `DEFINE_SPINLOCK()` to initialize it statically.
Fixes: e5f8efa5c8bf ("ARM: socfpga: fpga bridge driver support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-By: Moritz Fischer <mdf@kernel.org> Signed-off-by: Alan Tull <atull@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):
drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_done':
drivers/crypto/caam/caamalg_qi.c:794:2: error: implicit declaration of function 'dbg_dump_sg' [-Werror=implicit-function-declaration]
dbg_dump_sg(KERN_ERR, "dst @" __stringify(__LINE__)": ",
Since dbg_dump_sg() is shared between caam/jr and caam/qi, move it
in a shared location and export it.
At the same time:
-reduce ifdeferry by providing a no-op implementation for !DEBUG case
-rename it to caam_dump_sg() to be consistent in terms of
exported symbols namespace (caam_*)
On binder_init() the devices string is duplicated and smashed into individual
device names which are passed along. However, the original duplicated string
wasn't freed in case binder_init() failed. Let's free it on error.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.
Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0. Fix this by shifting only by 4 bits to correctly get the upper nybble.
Detected by CoverityScan, CID#142891 ("Operands don't affect result")
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
binder_fd_array_object starts with a 4-byte header,
followed by a few fields that are 8 bytes when
ANDROID_BINDER_IPC_32BIT=N.
This can cause alignment issues in a 64-bit kernel
with a 32-bit userspace, as on x86_32 an 8-byte primitive
may be aligned to a 4-byte address. Pad with a __u32
to fix this.
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend") Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume") Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe") Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Daniel Mack <zonque@gmail.com> Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
The race was introduced by me in commit 971316f0503a ("epoll:
ep_unregister_pollwait() can use the freed pwq->whead"). I did not
realize that nothing can protect eventpoll after ep_poll_callback() sets
->whead = NULL, only whead->lock can save us from the race with
ep_free() or ep_remove().
Move ->whead = NULL to the end of ep_poll_callback() and add the
necessary barriers.
TODO: cleanup the ewake/EPOLLEXCLUSIVE logic, it was confusing even
before this patch.
Hopefully this explains use-after-free reported by syzcaller:
BUG: KASAN: use-after-free in debug_spin_lock_before
...
_raw_spin_lock_irqsave+0x4a/0x60 kernel/locking/spinlock.c:159
ep_poll_callback+0x29f/0xff0 fs/eventpoll.c:1148
this is spin_lock(eventpoll->lock),
...
Freed by task 17774:
...
kfree+0xe8/0x2c0 mm/slub.c:3883
ep_free+0x22c/0x2a0 fs/eventpoll.c:865
Fixes: 971316f0503a ("epoll: ep_unregister_pollwait() can use the freed pwq->whead") Reported-by: 范龙飞 <long7573@126.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since switching the I2C-over-AUX helpers, there have been regressions on
some display combinations due to us not having support for "address only"
transactions.
This commits enables support for them for GF119 and newer.
Earlier GPUs have been reverted to a custom I2C-over-AUX algorithm.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMe 1.3 specification defines the Optional Admin Command Support feature
flags, bit 8 set to '1' then the controller supports the Doorbell Buffer
Config command. Bit 7 is used for Virtualization Mangement command.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: f9f38e33 ("nvme: improve performance for virtual NVMe devices") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fail to get needed page for pool, need to put allocated pages
into pool. But current code has a miscalculation of allocated pages,
correct it.
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Monk Liu <monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'dir' parameter in xfrm_migrate() is a user-controlled byte which is used
as an array index. This can lead to an out-of-bound access, kernel lockup and
DoS. Add a check for the 'dir' value.
Using sg_miter_start and sg_miter_next, the buffer of an SG is kmap'ed
to *buff. The current code calls sg_miter_stop (and thus kunmap) on the
SG entry before the last access of *buff.
The patch moves the sg_miter_stop call after the last access to *buff to
ensure that the memory pointed to by *buff is still mapped.
Fixes: 4816c9406430 ("lib/mpi: Fix SG miter leak") Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
[ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
[ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
.owner_cpu: 0
[ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W 4.12.0-03002-gec979a4-dirty #40
[ 5668.772796] Hardware name: Nokia RX-51 board
[ 5668.773071] Workqueue: phy1 wl1251_irq_work
[ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
(show_stack+0x10/0x14)
[ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
(do_raw_spin_lock+0x6c/0xa0)
[ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
(_raw_spin_lock_irqsave+0x10/0x18)
[ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
(wl1251_op_tx+0x38/0x5c)
[ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
(ieee80211_tx_frags+0x188/0x1c0)
[ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
(__ieee80211_tx+0x6c/0x130)
[ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
(ieee80211_tx+0xdc/0x104)
[ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
(__ieee80211_subif_start_xmit+0x454/0x8c8)
[ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
[<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
[ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
[<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...
by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmwgfx currently cannot support non-blocking commit because when
vmw_*_crtc_page_flip is called, drm_atomic_nonblocking_commit()
schedules the update on a thread. This means vmw_*_crtc_page_flip
cannot rely on the new surface being bound before the subsequent
dirty and flush operations happen.
Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Charmaine Lee <charmainel@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the block layer in single queue mode, get_request()
returns ERR_PTR(-EAGAIN) if the queue is dying and the REQ_NOWAIT
flag has been passed to get_request(). Avoid that the kernel
reports soft lockup complaints in this case due to continuous
requeuing activity.
Fixes: 7083abbbf ("dm mpath: avoid that path removal can trigger an infinite loop") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Tested-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent patch had an endian warning ie
cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup()
Signed-off-by: Steve French <smfrench@gmail.com> CC: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the maximum size of SMB2/3 header is set incorrectly which
leads to hanging of directory listing operations on encrypted SMB3
connections. Fix this by setting the maximum size to 170 bytes that
is calculated as RFC1002 length field size (4) + transform header
size (52) + SMB2 header size (64) + create response size (56).
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Acked-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tests/attr.c: In function 'store_event':
tests/attr.c:66:27: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__u64 {aka long unsigned int}' [-Werror=format=]
snprintf(path, PATH_MAX, "%s/event-%d-%llu-%d", dir,
^
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory_pressure control file was incorrectly set up without
a private value (0, by default). As a result, this control
file was treated like memory_migrate on read. By adding back the
FILE_MEMORY_PRESSURE private value, the correct memory pressure value
will be returned.
Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 7dbdb199d3bf ("cgroup: replace cftype->mode with CFTYPE_WORLD_WRITABLE") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When !NUMA, cpumask_of_node(@node) equals cpu_online_mask regardless of
@node. The assumption seems that if !NUMA, there shouldn't be more than
one node and thus reporting cpu_online_mask regardless of @node is
correct. However, that assumption was broken years ago to support
DISCONTIGMEM and whether a system has multiple nodes or not is
separately controlled by NEED_MULTIPLE_NODES.
This means that, on a system with !NUMA && NEED_MULTIPLE_NODES,
cpumask_of_node() will report cpu_online_mask for all possible nodes,
indicating that the CPUs are associated with multiple nodes which is an
impossible configuration.
This bug has been around forever but doesn't look like it has caused any
noticeable symptoms. However, it triggers a WARN recently added to
workqueue to verify NUMA affinity configuration.
Fix it by reporting empty cpumask on non-zero nodes if !NUMA.
ceph_readpage() unlocks page prematurely prematurely in the case
that page is reading from fscache. Caller of readpage expects that
page is uptodate when it get unlocked. So page shoule get locked
by completion callback of fscache_read_or_alloc_pages()
Wendy Wang reported off-list that a RAS HWPOISON-SOFT test case failed
and bisected it to the commit 479f854a207c ("mm, page_alloc: defer
debugging checks of pages allocated from the PCP").
The problem is that a page that was poisoned with madvise() is reused.
The commit removed a check that would trigger if DEBUG_VM was enabled
but re-enabling the check only fixes the problem as a side-effect by
printing a bad_page warning and recovering.
The root of the problem is that an madvise() can leave a poisoned page
on the per-cpu list. This patch drains all per-cpu lists after pages
are poisoned so that they will not be reused. Wendy reports that the
test case in question passes with this patch applied. While this could
be done in a targeted fashion, it is over-complicated for such a rare
operation.
Commit 7c051267931a ("mm, fork: make dup_mmap wait for mmap_sem for
write killable") made it possible to kill a forking task while it is
waiting to acquire its ->mmap_sem for write, in dup_mmap().
However, it was overlooked that this introduced an new error path before
the new mm_struct's ->uprobes_state.xol_area has been set to NULL after
being copied from the old mm_struct by the memcpy in dup_mm(). For a
task that has previously hit a uprobe tracepoint, this resulted in the
'struct xol_area' being freed multiple times if the task was killed at
just the right time while forking.
Fix it by setting ->uprobes_state.xol_area to NULL in mm_init() rather
than in uprobe_dup_mmap().
With CONFIG_UPROBE_EVENTS=y, the bug can be reproduced by the same C
program given by commit 2b7e8665b4ff ("fork: fix incorrect fput of
->exe_file causing use-after-free"), provided that a uprobe tracepoint
has been set on the fork_thread() function. For example:
For asynchronous operation, SGs are allocated without a page mapped to
them or with a page that is not used (ref-counted). If the SGL is freed,
the code must only call put_page for an SG if there was a page assigned
and ref-counted in the first place.
This fixes a kernel crash when using io_submit with more than one iocb
using the sendmsg and sendpage (vmsplice/splice) interface.
Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9ae433bc79f9 ("crypto: chacha20 - convert generic and x86 versions
to skcipher") ported the existing chacha20 code to use the new skcipher
API, and introduced a bug along the way. Unfortunately, the tcrypt tests
did not catch the error, and it was only found recently by Tobias.
Stefan kindly diagnosed the error, and proposed a fix which is similar
to the one below, with the exception that 'walk.stride' is used rather
than the hardcoded block size. This does not actually matter in this
case, but it's a better example of how to use the skcipher walk API.
Fixes: 9ae433bc79f9 ("crypto: chacha20 - convert generic and x86 ...") Cc: Steffen Klassert <steffen.klassert@secunet.com> Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.
When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.
Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.
User-modified input settings no longer survive a suspend/resume cycle.
Starting with 4.12, the touchpad is reinitialized on every reconnect
because the hardware appears to be different. This can be reproduced
by running the following as root:
[30378.295794] psmouse serio1: synaptics: hardware appears to be
different: id(149271-149271), model(114865-114865),
caps(d047b3-d047b1), ext(b40000-b40000).
Note the single bit difference in caps: bit 1 (SYN_CAP_MULTIFINGER).
This happens because we modify our stored copy of the device info
capabilities when we enable advanced gesture mode but this change is
not reflected in the actual hardware capabilities.
It worked in the past because synaptics_query_hardware used to modify
the stored synaptics_device_info struct instead of filling in a new
one, as it does now.
Fix it by no longer faking the SYN_CAP_MULTIFINGER bit when setting
advanced gesture mode. This necessitated a small refactoring.
Fixes: 6c53694fb222 ("Input: synaptics - split device info into a separate structure") Signed-off-by: Anthony Martin <ality@pbrane.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support") Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The x86 version of insb/insw/insl uses an inline assembly that does
not have the target buffer listed as an output. This can confuse
the compiler, leading it to think that a subsequent access of the
buffer is uninitialized:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_mgmt_scan_confirm’:
drivers/net/wireless/wl3501_cs.c:665:9: error: ‘sig.status’ is used uninitialized in this function [-Werror=uninitialized]
drivers/net/wireless/wl3501_cs.c:668:12: error: ‘sig.cap_info’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c: In function 'sb1000_rx':
drivers/net/sb1000.c:775:9: error: 'st[0]' is used uninitialized in this function [-Werror=uninitialized]
drivers/net/sb1000.c:776:10: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c:784:11: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I tried to mark the exact input buffer as an output here, but couldn't
figure it out. As suggested by Linus, marking all memory as clobbered
however is good enough too. For the outs operations, I also add the
memory clobber, to force the input to be written to local variables.
This is probably already guaranteed by the "asm volatile", but it can't
hurt to do this for symmetry.
When there's a fatal signal pending, arm64's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Laura Abbott <labbott@redhat.com> Reviewed-by: Steve Capper <steve.capper@arm.com> Tested-by: Steve Capper <steve.capper@arm.com> Reviewed-by: James Morse <james.morse@arm.com> Tested-by: James Morse <james.morse@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no guarantee that the various isync's involved with
the context switch will order the update of the CPU mask with
the first TLB entry for the new context being loaded by the HW.
Be safe here and add a memory barrier to order any subsequent
load/store which may bring entries into the TLB.
The corresponding barrier on the other side already exists as
pte updates use pte_xchg() which uses __cmpxchg_u64 which has
a sync after the atomic operation.
Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add comments in the code]
[mpe: Backport to 4.12, minor context change] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle
EC events) introduced acpi_ec_ecdt_start(), but that function is
invoked before acpi_ec_query_init(), which is too early. This causes
the kernel to crash if an EC event occurs after boot, when ec_query_wq
is not valid:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
...
Workqueue: events acpi_ec_event_handler
task: ffff9f539790dac0 task.stack: ffffb437c0e10000
RIP: 0010:__queue_work+0x32/0x430
Normally, the DSDT EC should always be valid, so acpi_ec_ecdt_start()
is actually a no-op in the majority of cases. However, commit c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe)
caused the probing of the DSDT EC as the "boot EC" to be skipped when
the ECDT EC is valid and uncovered the bug.
Fix this issue by invoking acpi_ec_ecdt_start() after acpi_ec_query_init()
in acpi_ec_init().
Link: https://jira01.devtools.intel.com/browse/LCK-4348 Fixes: 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle EC events) Fixes: c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe) Reported-by: Wang Wendy <wendy.wang@intel.com> Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI HID for Hisilicon Hip07/08 should be HISI02A1/2,
not HISI0A21/2, HISI02A1/2 was tested ok but was modified
by the stupid typo when upstream the patches (by me),
correct them to the right IDs (matching the IDs in
drivers/i2c/busses/i2c-designware-platdrv.c).
Fixes: 6e14cf361a0c (ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller) Reported-by: Tao Tian <tiantao6@huawei.com> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that under certain scenarios the SPAD can have bogus values caused
by an agent (i.e. BIOS or other software) that is not the kernel driver, and
that causes memory window setup failure. This should not cause the link to
be disabled because if we do that, the driver will never recover again. We
have verified in testing that this issue happens and prevents proper link
recovery.
Signed-off-by: Dave Jiang <dave.jiang@intel.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Fixes: 84f766855f61 ("ntb: stop link work when we do not have memory") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the link tests, there is a race on one side of the test for
the link coming up. It's possible, in some cases, for the test script
to write to the 'peer_trans' files before the link has come up.
To fix this, we simply use the link event file to ensure both sides
see the link as up before continuning.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Fixes: a9c59ef77458 ("ntb_test: Add a selftest script for the NTB subsystem") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a MAX_LFS_FILESIZE macro that is meant to be filled in by
filesystems (and other IO targets) that know they are 64-bit clean and
don't have any 32-bit limits in their IO path.
It turns out that our 32-bit value for that limit was bogus. On 32-bit,
the VM layer is limited by the page cache to only 32-bit index values,
but our logic for that was confusing and actually wrong. We used to
define that value to
(((loff_t)PAGE_SIZE << (BITS_PER_LONG-1))-1)
which is actually odd in several ways: it limits the index to 31 bits,
and then it limits files so that they can't have data in that last byte
of a page that has the highest 31-bit index (ie page index 0x7fffffff).
Neither of those limitations make sense. The index is actually the full
32 bit unsigned value, and we can use that whole full page. So the
maximum size of the file would logically be "PAGE_SIZE << BITS_PER_LONG".
However, we do wan tto avoid the maximum index, because we have code
that iterates over the page indexes, and we don't want that code to
overflow. So the maximum size of a file on a 32-bit host should
actually be one page less than the full 32-bit index.
So the actual limit is ULONG_MAX << PAGE_SHIFT. That means that we will
not actually be using the page of that last index (ULONG_MAX), but we
can grow a file up to that limit.
The wrong value of MAX_LFS_FILESIZE actually caused problems for Doug
Nazar, who was still using a 32-bit host, but with a 9.7TB 2 x RAID5
volume. It turns out that our old MAX_LFS_FILESIZE was 8TiB (well, one
byte less), but the actual true VM limit is one page less than 16TiB.
This was invisible until commit c2a9737f45e2 ("vfs,mm: fix a dead loop
in truncate_inode_pages_range()"), which started applying that
MAX_LFS_FILESIZE limit to block devices too.
NOTE! On 64-bit, the page index isn't a limiter at all, and the limit is
actually just the offset type itself (loff_t), which is signed. But for
clarity, on 64-bit, just use the maximum signed value, and don't make
people have to count the number of 'f' characters in the hex constant.
So just use LLONG_MAX for the 64-bit case. That was what the value had
been before too, just written out as a hex constant.
Fixes: c2a9737f45e2 ("vfs,mm: fix a dead loop in truncate_inode_pages_range()") Reported-and-tested-by: Doug Nazar <nazard@nazar.ca> Cc: Andreas Dilger <adilger@dilger.ca> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Dave Kleikamp <shaggy@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct iommu_device has a 'struct device' embedded into
it, not as a pointer, but the whole struct. In the
conversion of the iommu drivers to use struct iommu_device
it was forgotten that the relase function for that struct
device simply calls kfree() on the pointer.
This frees memory that was never allocated and causes memory
corruption.
To fix this issue, use a pointer to struct device instead of
embedding the whole struct. This needs some updates in the
iommu sysfs code as well as the Intel VT-d and AMD IOMMU
driver.
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Fixes: 39ab9555c241 ('iommu: Add sysfs bindings for struct iommu_device') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Commit c4ea41ba195d ("binder: use group leader instead of open thread")'
was incomplete and didn't update a check in binder_mmap(), causing all
mmap() calls into the binder driver to fail.
Use wake_up_interruptible_sync() to hint to the scheduler binder
transactions are synchronous wakeups. Disable preemption while waking
to avoid ping-ponging on the binder lock.
The binder allocator assumes that the thread that
called binder_open will never die for the lifetime of
that proc. That thread is normally the group_leader,
however it may not be. Use the group_leader instead
of current.
The patch introduced a race in the binder driver. An attempt to fix the
race was submitted in "[PATCH v2] android: binder: fix dangling pointer
comparison", however the conclusion in the discussion for that patch
was that the original patch should be reverted.
The reversion is being done as part of the fine-grained locking
patchset since the patch would need to be refactored when
proc->vmm_vm_mm is removed from struct binder_proc and added
in the binder allocator.
Verify that the length of the socket buffer is sufficient to cover the
nlmsghdr structure before accessing the nlh->nlmsg_len field for further
input sanitization. If the client only supplies 1-3 bytes of data in
sk_buff, then nlh->nlmsg_len remains partially uninitialized and
contains leftover memory from the corresponding kernel allocation.
Operating on such data may result in indeterminate evaluation of the
nlmsg_len < NLMSG_HDRLEN expression.
The bug was discovered by a runtime instrumentation designed to detect
use of uninitialized memory in the kernel. The patch prevents this and
other similar tools (e.g. KMSAN) from flagging this behavior in the future.
When doing initial conversion to rhashtable I replaced the bucket
walk with a single rhashtable_lookup_fast().
When moving to rhlist I failed to properly walk the list of identical
tuples, but that is what is needed for this to work correctly.
The table contains the original tuples, so the reply tuples are all
distinct.
We currently decide that mapping is (not) in range only based on the
first entry, but in case its not we need to try the reply tuple of the
next entry until we either find an in-range mapping or we checked
all the entries.
This bug makes nat core attempt collision resolution while it might be
able to use the mapping as-is.
We crash in __nf_ct_expect_check, it calls nf_ct_remove_expect on the
uninitialised expectation instead of existing one, so del_timer chokes
on random memory address.
While running nfs/connectathon tests kernel NULL-pointer exception
has been observed due to races in svcsock.c.
Race is appear when kernel accepts connection by kernel_accept
(which creates new socket) and start queuing ingress packets
to new socket. This happens in ksoftirq context which could run
concurrently on a different core while new socket setup is not done yet.
The fix is to re-order socket user data init sequence and add
write/read barrier calls to be sure that we got proper values
for callback pointers before actually calling them.
Test results: nfs/connectathon reports '0' failed tests for about 200+ iterations.
39a0526fb3f7 ("x86/mm: Factor out LDT init from context init")
renamed init_new_context() to init_new_context_ldt() and added a new
init_new_context() which calls init_new_context_ldt(). However, the
error code of init_new_context_ldt() was ignored. Consequently, if a
memory allocation in alloc_ldt_struct() failed during a fork(), the
->context.ldt of the new task remained the same as that of the old task
(due to the memcpy() in dup_mm()). ldt_struct's are not intended to be
shared, so a use-after-free occurred after one task exited.
Fix the bug by making init_new_context() pass through the error code of
init_new_context_ldt().
This bug was found by syzkaller, which encountered the following splat:
BUG: KASAN: use-after-free in free_ldt_struct.part.2+0x10a/0x150 arch/x86/kernel/ldt.c:116
Read of size 4 at addr ffff88006d2cb7c8 by task kworker/u9:0/3710
Note: the reproducer takes advantage of the fact that alloc_ldt_struct()
may use vmalloc() to allocate a large ->entries array, and after
commit:
5d17a73a2ebe ("vmalloc: back off when the current task is killed")
it is possible for userspace to fail a task's vmalloc() by
sending a fatal signal, e.g. via exit_group(). It would be more
difficult to reproduce this bug on kernels without that commit.
This bug only affected kernels with CONFIG_MODIFY_LDT_SYSCALL=y.
Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Fixes: 39a0526fb3f7 ("x86/mm: Factor out LDT init from context init") Link: http://lkml.kernel.org/r/20170824175029.76040-1-ebiggers3@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a timer base is idle, it is forwarded when a new timer is added
to ensure that granularity does not become excessive. When not idle,
the timer tick is expected to increment the base.
However there are several problems:
- If an existing timer is modified, the base is forwarded only after
the index is calculated.
- The base is not forwarded by add_timer_on.
- There is a window after a timer is restarted from a nohz idle, after
it is marked not-idle and before the timer tick on this CPU, where a
timer may be added but the ancient base does not get forwarded.
These result in excessive granularity (a 1 jiffy timeout can blow out
to 100s of jiffies), which cause the rcu lockup detector to trigger,
among other things.
Fix this by keeping track of whether the timer base has been idle
since it was last run or forwarded, and if so then forward it before
adding a new timer.
There is still a case where mod_timer optimises the case of a pending
timer mod with the same expiry time, where the timer can see excessive
granularity relative to the new, shorter interval. A comment is added,
but it's not changed because it is an important fastpath for
networking.
This has been tested and found to fix the RCU softlockup messages.
Testing was also done with tracing to measure requested versus
achieved wakeup latencies for all non-deferrable timers in an idle
system (with no lockup watchdogs running). Wakeup latency relative to
absolute latency is calculated (note this suffers from round-up skew
at low absolute times) and analysed:
The bug was noticed due to the lockup detector Kconfig changes
dropping it out of people's .configs and resulting in larger base
clk skew When the lockup detectors are enabled, no CPU can go idle for
longer than 4 seconds, which limits the granularity errors.
Sub-optimal timer behaviour is observable on a smaller scale in that
case:
Regardless of which events form a group, it does not make sense for the
events to target different tasks and/or CPUs, as this leaves the group
inconsistent and impossible to schedule. The core perf code assumes that
these are consistent across (successfully intialised) groups.
Core perf code only verifies this when moving SW events into a HW
context. Thus, we can violate this requirement for pure SW groups and
pure HW groups, unless the relevant PMU driver happens to perform this
verification itself. These mismatched groups subsequently wreak havoc
elsewhere.
For example, we handle watchpoints as SW events, and reserve watchpoint
HW on a per-CPU basis at pmu::event_init() time to ensure that any event
that is initialised is guaranteed to have a slot at pmu::add() time.
However, the core code only checks the group leader's cpu filter (via
event_filter_match()), and can thus install follower events onto CPUs
violating thier (mismatched) CPU filters, potentially installing them
into a CPU without sufficient reserved slots.
This can be triggered with the below test case, resulting in warnings
from arch backends.
int main(int argc, char *argv[])
{
int leader, ret;
cpu_set_t cpus;
/*
* Force use of CPU0 to ensure our CPU0-bound events get scheduled.
*/
CPU_ZERO(&cpus);
CPU_SET(0, &cpus);
ret = sched_setaffinity(0, sizeof(cpus), &cpus);
if (ret) {
printf("Unable to set cpu affinity\n");
return 1;
}
/* open leader event, bound to this task, CPU0 only */
leader = perf_event_open(&wp_attr, 0, 0, -1, 0);
if (leader < 0) {
printf("Couldn't open leader: %d\n", leader);
return 1;
}
/*
* Open a follower event that is bound to the same task, but a
* different CPU. This means that the group should never be possible to
* schedule.
*/
ret = perf_event_open(&wp_attr, 0, 1, leader, 0);
if (ret < 0) {
printf("Couldn't open mismatched follower: %d\n", ret);
return 1;
} else {
printf("Opened leader/follower with mismastched CPUs\n");
}
/*
* Open as many independent events as we can, all bound to the same
* task, CPU0 only.
*/
do {
ret = perf_event_open(&wp_attr, 0, 0, -1, 0);
} while (ret >= 0);
/*
* Force enable/disble all events to trigger the erronoeous
* installation of the follower event.
*/
printf("Opened all events. Toggling..\n");
for (;;) {
prctl(PR_TASK_PERF_EVENTS_DISABLE, 0, 0, 0, 0);
prctl(PR_TASK_PERF_EVENTS_ENABLE, 0, 0, 0, 0);
}
return 0;
}
Fix this by validating this requirement regardless of whether we're
moving events.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Zhou Chengming <zhouchengming1@huawei.com> Link: http://lkml.kernel.org/r/1498142498-15758-1-git-send-email-mark.rutland@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a small race when function graph shutsdown and the calling of the
registered function graph entry callback. The callback must not reference
the task's ret_stack without first checking that it is not NULL. Note, when
a ret_stack is allocated for a task, it stays allocated until the task exits.
The problem here, is that function_graph is shutdown, and a new task was
created, which doesn't have its ret_stack allocated. But since some of the
functions are still being traced, the callbacks can still be called.
The normal function_graph code handles this, but starting with commit 8861dd303c ("ftrace: Access ret_stack->subtime only in the function
profiler") the profiler code references the ret_stack on function entry, but
doesn't check if it is NULL first.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196611 Fixes: 8861dd303c ("ftrace: Access ret_stack->subtime only in the function profiler") Reported-by: lilydjwg@gmail.com Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for
virtqueues"") removed the adjustment of the pre_vectors for the virtio
MSI-X vector allocation which was added in commit fb5e31d9 ("virtio:
allow drivers to request IRQ affinity when creating VQs"). This will
lead to an incorrect assignment of MSI-X vectors, and potential
deadlocks when offlining cpus.
Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for virtqueues") Reported-by: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunyu Hu reported:
"per_cpu trace directories and files are created for all possible cpus,
but only the cpus which have ever been on-lined have their own per cpu
ring buffer (allocated by cpuhp threads). While trace_buffers_open, the
open handler for trace file 'trace_pipe_raw' is always trying to access
field of ring_buffer_per_cpu, and would panic with the NULL pointer.
Align the behavior of trace_pipe_raw with trace_pipe, that returns -NODEV
when openning it if that cpu does not have trace ring buffer.
Reproduce:
cat /sys/kernel/debug/tracing/per_cpu/cpu31/trace_pipe_raw
(cpu31 is never on-lined, this is a 16 cores x86_64 box)
Tested with:
1) boot with maxcpus=14, read trace_pipe_raw of cpu15.
Got -NODEV.
2) oneline cpu15, read trace_pipe_raw of cpu15.
Get the raw trace data.
This was introduced by the addition of the feature to reuse reader pages
instead of re-allocating them. The problem is that the allocation of a
reader page (which is per cpu) does not check if the cpu is online and set
up for the ring buffer.
Link: http://lkml.kernel.org/r/1500880866-1177-1-git-send-email-chuhu@redhat.com Fixes: 73a757e63114 ("ring-buffer: Return reader page back into existing ring buffer") Reported-by: Chunyu Hu <chuhu@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When processing an NFSv4 WRITE operation, argp->end should never
point past the end of the data in the final page of the page list.
Otherwise, nfsd4_decode_compound can walk into uninitialized memory.
More critical, nfsd4_decode_write is failing to increment argp->pagelen
when it increments argp->pagelist. This can cause later xdr decoders
to assume more data is available than really is, which can cause server
crashes on malformed requests.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The df for a SMB2 share triggers a GetInfo call for
FS_FULL_SIZE_INFORMATION. The values returned are used to populate
struct statfs.
The problem is that none of the information returned by the call
contains the total blocks available on the filesystem. Instead we use
the blocks available to the user ie. quota limitation when filling out
statfs.f_blocks. The information returned does contain Actual free units
on the filesystem and is used to populate statfs.f_bfree. For users with
quota enabled, it can lead to situations where the total free space
reported is more than the total blocks on the system ending up with df
reports like the following
# df -h /mnt/a
Filesystem Size Used Avail Use% Mounted on
//192.168.22.10/a 2.5G -2.3G 2.5G - /mnt/a
To fix this problem, we instead populate both statfs.f_bfree with the
same value as statfs.f_bavail ie. CallerAvailableAllocationUnits. This
is similar to what is done already in the code for cifs and df now
reports the quota information for the user used to mount the share.
# df --si /mnt/a
Filesystem Size Used Avail Use% Mounted on
//192.168.22.10/a 2.7G 101M 2.6G 4% /mnt/a
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Pierguido Lambri <plambri@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .data and .bss sections were modified in the generic linker script to
pull in sections named .data.<C identifier>, which are generated by gcc with
-ffunction-sections and -fdata-sections options.
The problem with this pattern is it can also match section names that Linux
defines explicitly, e.g., .data.unlikely. This can cause Linux sections to
get moved into the wrong place.
The way to avoid this is to use ".." separators for explicit section names
(the dot character is valid in a section name but not a C identifier).
However currently there are sections which don't follow this rule, so for
now just disable the wild card by default.
Initializing cq_context with ev_queue in create_cq(), leads to NULL pointer
dereference in ib_uverbs_comp_handler(), if application doesnot use completion
channel. This patch fixes the cq_context initialization.
Fixes: 1e7710f3f65 ("IB/core: Change completion channel to use the reworked") Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
(cherry picked from commit 699a2d5b1b880b4e4e1c7d55fa25659322cf5b51) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function create_filter() is passed a 'filterp' pointer that gets
allocated, and if "set_str" is true, it is up to the caller to free it, even
on error. The problem is that the pointer is not freed by create_filter()
when set_str is false. This is a bug, and it is not up to the caller to free
the filter on error if it doesn't care about the string.
Link: http://lkml.kernel.org/r/1502705898-27571-2-git-send-email-chuhu@redhat.com Fixes: 38b78eb85 ("tracing: Factorize filter creation") Reported-by: Chunyu Hu <chuhu@redhat.com> Tested-by: Chunyu Hu <chuhu@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clear_boot_tracer function is used to reset the default_bootup_tracer
string to prevent it from being accessed after boot, as it originally points
to init data. But since clear_boot_tracer() is called via the
init_lateinit() call, it races with the initcall for registering the hwlat
tracer. If someone adds "ftrace=hwlat" to the kernel command line, depending
on how the linker sets up the text, the saved command line may be cleared,
and the hwlat tracer never is initialized.
Simply have the clear_boot_tracer() be called by initcall_lateinit_sync() as
that's for tasks to be called after lateinit.
acpi_graph_get_child_prop_value() is intended to find a child node with a
certain property value pair. The check
if (!fwnode_property_read_u32(fwnode, prop_name, &nr))
continue;
is faulty: fwnode_property_read_u32() returns zero on success, not on
failure, leading to comparing values only if the searched property was not
found.
Moreover, the check is made against the parent device node instead of
the child one as it should be.
Fixes: 79389a83bc38 (ACPI / property: Add support for remote endpoints) Reported-by: Hyungwoo Yang <hyungwoo.yang@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
once error happens in shadow_indirect_ctx function, the variable
wa_ctx->indirect_ctx.obj is not initialized but accessed, so the
kernel null point panic occurs.
Fixes: 894cf7d15634 ("drm/i915/gvt: i915_gem_object_create() returns an error pointer") Signed-off-by: fred gao <fred.gao@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since we've parsed VBT child devices, starting from 6acab15a7b0d
("drm/i915: use the HDMI DDI buffer translations from VBT"), we've
ignored the child device information if more than one child device
references the same port. The rationale for this seems lost in time.
Since commit 311a20949f04 ("drm/i915: don't init DP or HDMI when not
supported by DDI port") we started using this information more to skip
HDMI/DP init if the port wasn't there per VBT child devices. However, at
the same time it added port defaults without further explanation.
Thus, if the child device info was skipped due to multiple child devices
referencing the same port, the device info would be retrieved from the
somewhat arbitrary defaults.
Finally, when commit bb1d132935c2 ("drm/i915/vbt: split out defaults
that are set when there is no VBT") stopped initializing the defaults
whenever VBT is present, thus trusting the VBT more, we stopped
initializing ports which were referenced by more than one child device.
Apparently at least Asus UX305UA, UX305U, and UX306U laptops have VBT
child device blocks which cause this behaviour. Arguably they were
shipped with a broken VBT.
Relax the rules for multiple references to the same port, and use the
first child device info to reference a port. Retain the logic to debug
log about this, though.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101745
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196233 Fixes: bb1d132935c2 ("drm/i915/vbt: split out defaults that are set when there is no VBT") Tested-by: Oliver Weißbarth <mail@oweissbarth.de> Reported-by: Oliver Weißbarth <mail@oweissbarth.de> Reported-by: Didier G <didierg-divers@orange.fr> Reported-by: Giles Anderson <agander@gmail.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170811113907.6716-1-jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit b5273d72750555a673040070bfb23c454a7cd3ef) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last part of drm_atomic_check_only is testing whether we need to
fail with -EINVAL when modeset is not allowed, but forgets to return
the value when atomic_check() fails first.
This results in -EDEADLK being replaced by -EINVAL, and the sanity
check in drm_modeset_drop_locks kicks in:
This is also a bugfix because we could end up rejecting updates with
-EINVAL because of a early -EDEADLK, while if atomic_check ran to
completion it might have downgraded the modeset to a fastset.
complete_crtc_signaling is freeing fence_state, but when retrying
num_fences and fence_state are not zero'd. This caused duplicate
fd's in the fence_state array, followed by a BUG_ON in fs/file.c
because we reallocate freed memory, and installing over an existing
fd, or potential other fun.
Zero fence_state and num_fences correctly in the retry loop, which
allows kms_atomic_transition to pass.
Fixes: beaf5af48034 ("drm/fence: add out-fences support") Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Cc: Brian Starkey <brian.starkey@arm.com> (v10) Cc: Sean Paul <seanpaul@chromium.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: kms_atomic_transitions.plane-all-modeset-transition-fencing
(with CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y) Link: https://patchwork.freedesktop.org/patch/msgid/20170814100721.13340-1-maarten.lankhorst@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #intel-gfx on irc Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drm_driver lastclose callback is called when the last userspace
DRM client has closed. Call drm_fbdev_cma_restore_mode to restore
the fbdev console otherwise the fbdev console will stop working.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support") Tested-by: Olliver Schinagl <oliver@schinagl.nl> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jonathan Liu <net147@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same bug as we fixed in commit f6cd7daecff5 ("drm: Release
driver references to handle before making it available again"), but now
the exposure is via the PRIME lookup tables. If we remove the
object/handle from the PRIME lut, then a new request for the same
object/fd will generate a new handle, thus for a short window that
object is known to userspace by two different handles. Fix this by
releasing the driver tracking before PRIME.
Fixes: 0ff926c7d4f0 ("drm/prime: add exported buffers to current fprivs
imported buffer list (v2)") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Thierry Reding <treding@nvidia.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170819120558.6465-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
