Since we now prevent regulatory restore during STA disconnect
if concurrent AP interfaces are active, we need to reschedule
this check when the AP state changes. This fixes never doing
a restore when an AP is the last interface to stop. Or to put
it another way: we need to re-check after anything we check
here changes.
Cc: stable@vger.kernel.org Fixes: 113f3aaa81bd ("cfg80211: Prevent regulatory restore during STA disconnect in concurrent interfaces") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing
to deliver SIGHUP but always trying.
When the stack overflows delivery of SIGHUP fails and force_sigsegv is
called. Unfortunately because SIGSEGV is numerically higher than
SIGHUP next_signal tries again to deliver a SIGHUP.
From a quality of implementation standpoint attempting to deliver the
timer SIGHUP signal is wrong. We should attempt to deliver the
synchronous SIGSEGV signal we just forced.
We can make that happening in a fairly straight forward manner by
instead of just looking at the signal number we also look at the
si_code. In particular for exceptions (aka synchronous signals) the
si_code is always greater than 0.
That still has the potential to pick up a number of asynchronous
signals as in a few cases the same si_codes that are used
for synchronous signals are also used for asynchronous signals,
and SI_KERNEL is also included in the list of possible si_codes.
Still the heuristic is much better and timer signals are definitely
excluded. Which is enough to prevent all known ways for someone
sending a process signals fast enough to cause unexpected and
arguably incorrect behavior.
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop
failing to deliver SIGHUP but always trying.
Upon examination it turns out part of the problem is actually most of
the solution. Since 2.5 signal delivery has found all fatal signals,
marked the signal group for death, and queued SIGKILL in every threads
thread queue relying on signal->group_exit_code to preserve the
information of which was the actual fatal signal.
The conversion of all fatal signals to SIGKILL results in the
synchronous signal heuristic in next_signal kicking in and preferring
SIGHUP to SIGKILL. Which is especially problematic as all
fatal signals have already been transformed into SIGKILL.
Instead of dequeueing signals and depending upon SIGKILL to
be the first signal dequeued, first test if the signal group
has already been marked for death. This guarantees that
nothing in the signal queue can prevent a process that needs
to exit from exiting.
Since 2.5.34 the code has had the potential to not allocate siginfo
for SIGSTOP signals. Except for ptrace this is perfectly fine as only
ptrace can use PTRACE_PEEK_SIGINFO and see what the contents of
the delivered siginfo are.
Users of PTRACE_PEEK_SIGINFO that care about the contents siginfo
for SIGSTOP are rare, but they do exist. A seccomp self test
has cared and lldb cares.
Jack Andersen <jackoalan@gmail.com> writes:
> The patch titled
> `signal: Never allocate siginfo for SIGKILL or SIGSTOP`
> created a regression for users of PTRACE_GETSIGINFO needing to
> discern signals that were raised via the tgkill syscall.
>
> A notable user of this tgkill+ptrace combination is lldb while
> debugging a multithreaded program. Without the ability to detect a
> SIGSTOP originating from tgkill, lldb does not have a way to
> synchronize on a per-thread basis and falls back to SIGSTOP-ing the
> entire process.
Everyone affected by this please note. The kernel can still fail to
allocate a siginfo structure. The allocation is with GFP_KERNEL and
is best effort only. If memory is tight when the signal allocation
comes in this will fail to allocate a siginfo.
So I strongly recommend looking at more robust solutions for
synchronizing with a single thread such as PTRACE_INTERRUPT. Or if
that does not work persuading your friendly local kernel developer to
build the interface you need.
Reported-by: Tycho Andersen <tycho@tycho.ws> Reported-by: Kees Cook <keescook@chromium.org> Reported-by: Jack Andersen <jackoalan@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Christian Brauner <christian@brauner.io> Cc: stable@vger.kernel.org Fixes: f149b3155744 ("signal: Never allocate siginfo for SIGKILL or SIGSTOP") Fixes: 6dfc88977e42 ("[PATCH] shared thread signals")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Jonathan Cameron, the buffer needs to allocate room for a
64 bit timestamp as well as the channels. Change the buffer
to allocate this additional space.
Fixes: 2a86487786b5c ("iio: adc: ti-ads8688: add trigger and buffer support") Signed-off-by: Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545 Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, num_loops is unsigned, but it's set by strtoll, which returns a
(signed) long long int. This could lead to overflow, and it also makes the
check "num_loops < 0" always be false, since num_loops is unsigned.
Setting num_loops to -1 to loop forever is almost working because num_loops
is getting set to a very high number, but it's technically still incorrect.
Fix this issue by making num_loops signed. This also fixes an error found
by Smatch.
Signed-off-by: Martin Kelly <mkelly@xevo.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 55dda0abcf9d ("tools: iio: iio_generic_buffer: allow continuous looping") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Reported-by: Stefan Roese <sr@denx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent
erase properties") introduced a check to make sure ->erasesize and
->_erase values are consistent with the MTD_NO_ERASE flag.
This patch did not take the 0 bytes partition case into account which
can happen when the defined partition is outside the flash device memory
range. Fix that by setting the partition erasesize to the parent
erasesize.
Fixes: 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent erase properties") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: <stable@vger.kernel.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the parameter 'count' is non-zero, nfsd4_clone_file_range() will
currently clobber all errors returned by vfs_clone_file_range() and
replace them with EINVAL.
Fixes: 42ec3d4c0218 ("vfs: make remap_file_range functions take and...") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 448a5a552f336bd7b847b1951 ("drivers: base: cacheinfo: use OF
property_read_u32 instead of get_property,read_number") makes cache
size and number_of_sets be 0 if DT doesn't provide there values. I
think this is unreasonable so make them keep the old values, which is
the same as old kernels.
Fixes: 448a5a552f33 ("drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number") Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae735 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts") Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There still is a race window after the commit b027e2298bd588
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com> Tested-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Wang Li <wangli39@baidu.com> Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notice that the use of the bitwise OR operator '|' always leads to true
in this particular case, which seems a bit suspicious due to the context
in which this expression is being used.
Fix this by using bitwise AND operator '&' instead.
This bug was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Fixes: 6a6cd11d4e57 ("perf test: Add test for the sched tracepoint format fields") Link: http://lkml.kernel.org/r/20190122233439.GA5868@embeddedor Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf tool uses /proc/sys/kernel/perf_event_mlock_kb to determine how
large its ringbuffer mmap should be. This can be configured to arbitrary
values, which can be larger than the maximum possible allocation from
kmalloc.
When this is configured to a suitably large value (e.g. thanks to the
perf fuzzer), attempting to use perf record triggers a WARN_ON_ONCE() in
__alloc_pages_nodemask():
WARNING: CPU: 2 PID: 5666 at mm/page_alloc.c:4511 __alloc_pages_nodemask+0x3f8/0xbc8
Let's avoid this by checking that the requested allocation is possible
before calling kzalloc.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20190110142745.25495-1-mark.rutland@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal injection testing crashed with a console log that said:
mce: [Hardware Error]: CPU 7: Machine Check Exception: f Bank 0: bd80000000100134
This caused a lot of head scratching because the MCACOD (bits 15:0) of
that status is a signature from an L1 data cache error. But Linux says
that it found it in "Bank 0", which on this model CPU only reports L1
instruction cache errors.
The answer was that Linux doesn't initialize "m->bank" in the case that
it finds a fatal error in the mce_no_way_out() pre-scan of banks. If
this was a local machine check, then this partially initialized struct
mce is being passed to mce_panic().
Fix is simple: just initialize m->bank in the case of a fatal error.
Fixes: 40c36e2741d7 ("x86/mce: Fix incorrect "Machine check from unknown source" message") Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: x86-ml <x86@kernel.org> Cc: stable@vger.kernel.org # v4.18 Note pre-v5.0 arch/x86/kernel/cpu/mce/core.c was called arch/x86/kernel/cpu/mcheck/mce.c Link: https://lkml.kernel.org/r/20190201003341.10638-1-tony.luck@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
intel_pmu_cpu_prepare() allocated memory for ->shared_regs among other
members of struct cpu_hw_events. This memory is released in
intel_pmu_cpu_dying() which is wrong. The counterpart of the
intel_pmu_cpu_prepare() callback is x86_pmu_dead_cpu().
Otherwise if the CPU fails on the UP path between CPUHP_PERF_X86_PREPARE
and CPUHP_AP_PERF_X86_STARTING then it won't release the memory but
allocate new memory on the next attempt to online the CPU (leaking the
old memory).
Also, if the CPU down path fails between CPUHP_AP_PERF_X86_STARTING and
CPUHP_PERF_X86_PREPARE then the CPU will go back online but never
allocate the memory that was released in x86_pmu_dying_cpu().
Make the memory allocation/free symmetrical in regard to the CPU hotplug
notifier by moving the deallocation to intel_pmu_cpu_dead().
This started in commit:
a7e3ed1e47011 ("perf: Add support for supplementary event registers").
In principle the bug was introduced in v2.6.39 (!), but it will almost
certainly not backport cleanly across the big CPU hotplug rewrite between v4.7-v4.15...
Reported-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With developer hat on Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With maintainer hat on Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: acme@kernel.org Cc: bp@alien8.de Cc: hpa@zytor.com Cc: jolsa@kernel.org Cc: kan.liang@linux.intel.com Cc: namhyung@kernel.org Cc: <stable@vger.kernel.org> Fixes: a7e3ed1e47011 ("perf: Add support for supplementary event registers"). Link: https://lkml.kernel.org/r/20181219165350.6s3jvyxbibpvlhtq@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCI uncore PMUs cannot be registered on an 8-socket system (HPE
Superdome Flex).
To understand which Socket the PCI uncore PMUs belongs to, perf retrieves
the local Node ID of the uncore device from CPUNODEID(0xC0) of the PCI
configuration space, and the mapping between Socket ID and Node ID from
GIDNIDMAP(0xD4). The Socket ID can be calculated accordingly.
The local Node ID is only available at bit 2:0, but current code doesn't
mask it. If a BIOS doesn't clear the rest of the bits, an incorrect Node ID
will be fetched.
Filter the Node ID by adding a mask.
Reported-by: Song Liu <songliubraving@fb.com> Tested-by: Song Liu <songliubraving@fb.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> # v3.7+ Fixes: 7c94ee2e0917 ("perf/x86: Add Intel Nehalem and Sandy Bridge-EP uncore support") Link: https://lkml.kernel.org/r/1548600794-33162-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS") Reported-by: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Joe Mario <jmario@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple code paths where an hrtimer may have been started to
emulate an L1 VMX preemption timer that can result in a call to free_nested
without an intervening L2 exit where the hrtimer is normally
cancelled. Unconditionally cancel in free_nested to cover all cases.
Embargoed until Feb 7th 2019.
Signed-off-by: Peter Shier <pshier@google.com> Reported-by: Jim Mattson <jmattson@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org
Message-Id: <20181011184646.154065-1-pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. creates a device that holds a reference to the VM object (with a borrowed
reference, the VM's refcount has not been bumped yet)
2. initializes the device
3. transfers the reference to the device to the caller's file descriptor table
4. calls kvm_get_kvm() to turn the borrowed reference to the VM into a real
reference
The ownership transfer in step 3 must not happen before the reference to the VM
becomes a proper, non-borrowed reference, which only happens in step 4.
After step 3, an attacker can close the file descriptor and drop the borrowed
reference, which can cause the refcount of the kvm object to drop to zero.
This means that we need to grab a reference for the device before
anon_inode_getfd(), otherwise the VM can disappear from under us.
Emulation of certain instructions (VMXON, VMCLEAR, VMPTRLD, VMWRITE with
memory operand, INVEPT, INVVPID) can incorrectly inject a page fault
when passed an operand that points to an MMIO address. The page fault
will use uninitialized kernel stack memory as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just
ensure that the error code and CR2 are zero.
Embargoed until Feb 7th 2019.
Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the PCI code had recently added a file named 'revision' to every
PCI device. Fix this by renaming the aic94xx revision file to
aic_revision. This is safe to do for us because as far as I can tell,
there's nothing in userspace relying on the current aic94xx revision file
so it can be renamed without breaking anything.
Fixes: 702ed3be1b1b (PCI: Create revision file in sysfs) Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently when an error is encountered during probe of the cxlflash
adapter, a deadlock is seen with cpu thread stuck inside
cxlflash_remove(). Below is the trace of the deadlock as logged by
khungtaskd:
cxlflash 0006:00:00.0: cxlflash_probe: init_afu failed rc=-16
INFO: task kworker/80:1:890 blocked for more than 120 seconds.
Not tainted 5.0.0-rc4-capi2-kexec+ #2
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/80:1 D 0 890 2 0x00000808
Workqueue: events work_for_cpu_fn
Call Trace:
0x4d72136320 (unreliable)
__switch_to+0x2cc/0x460
__schedule+0x2bc/0xac0
schedule+0x40/0xb0
cxlflash_remove+0xec/0x640 [cxlflash]
cxlflash_probe+0x370/0x8f0 [cxlflash]
local_pci_probe+0x6c/0x140
work_for_cpu_fn+0x38/0x60
process_one_work+0x260/0x530
worker_thread+0x280/0x5d0
kthread+0x1a8/0x1b0
ret_from_kernel_thread+0x5c/0x80
INFO: task systemd-udevd:5160 blocked for more than 120 seconds.
The deadlock occurs as cxlflash_remove() is called from cxlflash_probe()
without setting 'cxlflash_cfg->state' to STATE_PROBED and the probe thread
starts to wait on 'cxlflash_cfg->reset_waitq'. Since the device was never
successfully probed the 'cxlflash_cfg->state' never changes from
STATE_PROBING hence the deadlock occurs.
We fix this deadlock by setting the variable 'cxlflash_cfg->state' to
STATE_PROBED in case an error occurs during cxlflash_probe() and just
before calling cxlflash_remove().
Cc: stable@vger.kernel.org Fixes: c21e0bbfc485("cxlflash: Base support for IBM CXL Flash Adapter") Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bf5054569653 ("block: Introduce blk_revalidate_disk_zones()")
inadvertently broke the message output of sd_zbc_print_zones() because the
zone information initialization of the scsi disk structure was moved to the
second scan run while sd_zbc_print_zones() is called on the first
scan. This leads to the following incorrect message to be printed for any
ZBC or ZAC zoned disks.
"...[sdX] 4294967295 zones of 0 logical blocks + 1 runt zone"
Fix this by initializing sdkp zone size and number of zones early on the
first scan. This does not impact the execution of
blk_revalidate_zones(). This functions is still called only once the block
device capacity is set on the second revalidate run on boot, or if the disk
zone configuration changed (i.e. the disk changed).
Fixes: bf5054569653 ("block: Introduce blk_revalidate_disk_zones()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The send_xchar() and tiocmset() tty operations are optional. Add the
missing sanity checks to prevent user-space triggerable NULL-pointer
dereferences.
Fixes: 6b9ad1c742bf ("staging: speakup: add send_xchar, tiocmset and input functionality for tty") Cc: stable <stable@vger.kernel.org> # 4.13 Cc: Okash Khawaja <okash.khawaja@gmail.com> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d76352 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup") Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f9151 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket") Cc: stable@vger.kernel.org Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems or VMs where multiple devices share a single DevID
(because they sit behind a PCI bridge, or because the HW is
broken in funky ways), we reuse the save its_device structure
in order to reflect this.
It turns out that there is a distinct lack of locking when looking
up the its_device, and two device being probed concurrently can result
in double allocations. That's obviously not nice.
A solution for this is to have a per-ITS mutex that serializes device
allocation.
A similar issue exists on the freeing side, which can run concurrently
with the allocation. On top of now taking the appropriate lock, we
also make sure that a shared device is never freed, as we have no way
to currently track the life cycle of such object.
commit 56222b212e8e ("futex: Drop hb->lock before enqueueing on the
rtmutex") changed the locking rules in the futex code so that the hash
bucket lock is not longer held while the waiter is enqueued into the
rtmutex wait list. This made the lock and the unlock path symmetric, but
unfortunately the possible early exit from __rt_mutex_proxy_start() due to
a detected deadlock was not updated accordingly. That allows a concurrent
unlocker to observe inconsitent state which triggers the warning in the
unlock path.
The problem is caused by the remove(rtmutex_waiter) in the failure case of
__rt_mutex_proxy_start() as this lets the unlocker observe a waiter in the
hash bucket but no waiter on the rtmutex, i.e. inconsistent state.
The original commit handles this correctly for the other early return cases
(timeout, signal) by delaying the removal of the rtmutex waiter until the
returning task reacquired the hash bucket lock.
Treat the failure case of __rt_mutex_proxy_start() in the same way and let
the existing cleanup code handle the eventual handover of the rtmutex
gracefully. The regular rt_mutex_proxy_start() gains the rtmutex waiter
removal for the failure case, so that the other callsites are still
operating correctly.
Add proper comments to the code so all these details are fully documented.
Thanks to Peter for helping with the analysis and writing the really
valuable code comments.
Fixes: 56222b212e8e ("futex: Drop hb->lock before enqueueing on the rtmutex") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Co-developed-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: linux-s390@vger.kernel.org Cc: Stefan Liebler <stli@linux.ibm.com> Cc: Sebastian Sewior <bigeasy@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1901292311410.1950@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the "ld_queue" list is not empty, next descriptor will migrate
into "ld_active" list. The "desc" variable will be overwritten
during that transition. And later the dmaengine_desc_get_callback_invoke()
will use it as an argument. As result we invoke wrong callback.
That behaviour was in place since:
commit fcaaba6c7136 ("dmaengine: imx-dma: fix callback path in tasklet").
But after commit 4cd13c21b207 ("softirq: Let ksoftirqd do its job")
things got worse, since possible delay between tasklet_schedule()
from DMA irq handler and actual tasklet function execution got bigger.
And that gave more time for new DMA request to be submitted and
to be put into "ld_queue" list.
It has been noticed that DMA issue is causing problems for "mxc-mmc"
driver. While stressing the system with heavy network traffic and
writing/reading to/from sd card simultaneously the timeout may happen:
10013000.sdhci: mxcmci_watchdog: read time out (status = 0x30004900)
There are multiple issues with bcm2835_dma_abort() (which is called on
termination of a transaction):
* The algorithm to abort the transaction first pauses the channel by
clearing the ACTIVE flag in the CS register, then waits for the PAUSED
flag to clear. Page 49 of the spec documents the latter as follows:
"Indicates if the DMA is currently paused and not transferring data.
This will occur if the active bit has been cleared [...]"
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
So the function is entering an infinite loop because it is waiting for
PAUSED to clear which is always set due to the function having cleared
the ACTIVE flag. The only thing that's saving it from itself is the
upper bound of 10000 loop iterations.
The code comment says that the intention is to "wait for any current
AXI transfer to complete", so the author probably wanted to check the
WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function
accordingly.
* The CS register is only read at the beginning of the function. It
needs to be read again after pausing the channel and before checking
for outstanding writes, otherwise writes which were issued between
the register read at the beginning of the function and pausing the
channel may not be waited for.
* The function seeks to abort the transfer by writing 0 to the NEXTCONBK
register and setting the ABORT and ACTIVE flags. Thereby, the 0 in
NEXTCONBK is sought to be loaded into the CONBLK_AD register. However
experimentation has shown this approach to not work: The CONBLK_AD
register remains the same as before and the CS register contains
0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control
block is not aborted but merely paused and it will be resumed once the
next DMA transaction is started. That is absolutely not the desired
behavior.
A simpler approach is to set the channel's RESET flag instead. This
reliably zeroes the NEXTCONBK as well as the CS register. It requires
less code and only a single MMIO write. This is also what popular
user space DMA drivers do, e.g.:
https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c
Note that the spec is contradictory whether the NEXTCONBK register
is writeable at all. On the one hand, page 41 claims:
"The value loaded into the NEXTCONBK register can be overwritten so
that the linked list of Control Block data structures can be
dynamically altered. However it is only safe to do this when the DMA
is paused."
On the other hand, page 40 specifies:
"Only three registers in each channel's register set are directly
writeable (CS, CONBLK_AD and DEBUG). The other registers (TI,
SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically
loaded from a Control Block data structure held in external memory."
If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf147
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187 Cc: stable@vger.kernel.org # v4.18+ Fixes: cd667ce24796 ("HID: use debugfs for events/reports dumping") Fixes: 717adfdaf147 ("HID: debug: check length before copy_to_user()") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the pipe_buf_release() handlers seem to assume that the pipe is
locked - in particular, anon_pipe_buf_release() accesses pipe->tmp_page
without taking any extra locks. From a glance through the callers of
pipe_buf_release(), it looks like FUSE is the only one that calls
pipe_buf_release() without having the pipe locked.
This bug should only lead to a memory leak, nothing terrible.
On the System76 Darter Pro (darp5), there is a headset microphone
input attached to 0x1a that does not have a jack detect. In order to
get it working, the pin configuration needs to be set correctly, and
the ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied.
This is similar to the MIC_NO_PRESENCE fixups for some Dell laptops,
except we have a separate microphone jack that is already configured
correctly.
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
This patch adds the T+A VID to the generic check in order to enable
native DSD support for T+A devices. This works with the new T+A USB
DAC model SD3100HV and will also work with future devices which
support the XMOS/Thesycon style DSD format.
It is normal user behaviour to start, stop, then start a stream
again without closing it. Currently this works for compressed
playback streams but not capture ones.
The states on a compressed capture stream go directly from OPEN to
PREPARED, unlike a playback stream which moves to SETUP and waits
for a write of data before moving to PREPARED. Currently however,
when a stop is sent the state is set to SETUP for both types of
streams. This leaves a capture stream in the situation where a new
start can't be sent as that requires the state to be PREPARED and
a new set_params can't be sent as that requires the state to be
OPEN. The only option being to close the stream, and then reopen.
Correct this issues by allowing snd_compr_drain_notify to set the
state depending on the stream direction, as we already do in
set_params.
Fixes: 49bb6402f1aa ("ALSA: compress_core: Add support for capture streams") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cached writeback mapping is EOF trimmed to try and avoid races
between post-eof block management and writeback that result in
sending cached data to a stale location. The cached mapping is
currently trimmed on the validation check, which leaves a race
window between the time the mapping is cached and when it is trimmed
against the current inode size.
For example, if a new mapping is cached by delalloc conversion on a
blocksize == page size fs, we could cycle various locks, perform
memory allocations, etc. in the writeback codepath before the
associated mapping is eventually trimmed to i_size. This leaves
enough time for a post-eof truncate and file append before the
cached mapping is trimmed. The former event essentially invalidates
a range of the cached mapping and the latter bumps the inode size
such the trim on the next writepage event won't trim all of the
invalid blocks. fstest generic/464 reproduces this scenario
occasionally and causes a lost writeback and stale delalloc blocks
warning on inode inactivation.
To work around this problem, trim the cached writeback mapping as
soon as it is cached in addition to on subsequent validation checks.
This is a minor tweak to tighten the race window as much as possible
until a proper invalidation mechanism is available.
Fixes: 40214d128e07 ("xfs: trim writepage mapping to within eof") Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.
Prior to:
commit '88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), Cc: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts") Fixes: b2ddc48a81b5 ("net: dsa: b53: Do not fail when IRQ are not initialized") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fl_change(), when adding a new rule (i.e. fold == NULL), a driver may
reject the new rule, for example due to resource exhaustion. By that
point, the new rule was already assigned a mask, and it was added to
that mask's hash table. The clean-up path that's invoked as a result of
the rejection however neglects to undo the hash table addition, and
proceeds to free the new rule, thus leaving a dangling pointer in the
hash table.
Fix by removing fnew from the mask's hash table before it is freed.
Fixes: 35cc3cefc4de ("net/sched: cls_flower: Reject duplicated rules also under skip_sw") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns. When servicing the interrupt, the
driver may crash when trying to access the doorbell.
Fix it by disabling interrupt on that vector until the doorbell is
set up.
Fixes: 697197e5a173 ("bnxt_en: Re-structure doorbells.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously virtnet_xdp_xmit() did not account for device tx counters,
which caused confusions.
To be consistent with SKBs, account them on freeing xdp_frames.
Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "p" buffer is 0x4000 bytes long. B3_RI_WTO_R1 is 0x190. The value
of "regs->len" is in the 1-0x4000 range. The bug here is that
"regs->len - B3_RI_WTO_R1" can be a negative value which would lead to
memory corruption and an abrupt crash.
Fixes: c3f8be961808 ("[PATCH] skge: expand ethtool debug register dump") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sctp_sendmesg(), when walking the list of endpoint associations, the
association can be dropped from the list, making the list corrupt.
Properly handle this by using list_for_each_entry_safe()
Fixes: 4910280503f3 ("sctp: add support for snd flag SCTP_SENDALL process in sendmsg") Reported-by: Secunia Research <vuln@secunia.com> Tested-by: Secunia Research <vuln@secunia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now when using stream reconfig to add out streams, stream->out
will get re-allocated, and all old streams' information will
be copied to the new ones and the old ones will be freed.
So without stream->out_curr updated, next time when trying to
send from stream->out_curr stream, a panic would be caused.
This patch is to check and update stream->out_curr when
allocating stream_out.
v1->v2:
- define fa_index() to get elem index from stream->out_curr.
v2->v3:
- repost with no change.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: Ying Xu <yinxu@redhat.com> Reported-by: syzbot+e33a3a138267ca119c7d@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When either "goto wait_interrupted;" or "goto wait_error;"
paths are taken, socket lock has already been released.
This patch fixes following syzbot splat :
WARNING: bad unlock balance detected!
5.0.0-rc4+ #59 Not tainted
-------------------------------------
syz-executor223/8256 is trying to release lock (sk_lock-AF_RXRPC) at:
[<ffffffff86651353>] rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598
but there are no more locks to release!
other info that might help us debug this:
1 lock held by syz-executor223/8256:
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: spin_lock_bh include/linux/spinlock.h:334 [inline]
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2798
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Howells <dhowells@redhat.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original diagnosis was incorrect: it appears that the NIC had
PHY polling mode enabled, which meant that it overwrote the PHYs
advertisement register during negotiation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broadcom STB chips support a deep sleep mode where all register
contents are lost. Because we were stashing the MagicPacket password
into some of these registers a suspend into that deep sleep then a
resumption would not lead to being able to wake-up from MagicPacket with
password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Rundong Ge <rdong.ge@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.
Fix this by using the source port ID for the violation, which really
is a port number.
Reported-by: Chris Healy <Chris.Healy@zii.aero> Tested-by: Chris Healy <Chris.Healy@zii.aero> Fixes: 65f60e4582bd ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed3e ("dsa: slave: eee: Allow ports to use phylink") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This looks fairly harmless (no actual deadlock occurs), and is
fixed in a similar way to c6894dec8ea9 ("bridge: fix lockdep
addr_list_lock false positive splat") by putting the addr_list_lock
in its own lockdep class.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test_insert_dup() function from lib/test_rhashtable.c passes a
pointer to a stack object to rhltable_init(). Allocate the hash table
dynamically to avoid that the following is reported with object
debugging enabled:
Cc: Thomas Graf <tgraf@suug.ch> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does
not set skb->ip_summed. So IPv6 rx checksum is not offloaded.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid warnings like this:
thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function]
thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
Fixes: 0dd88793aacd ("thermal: hwmon: move hwmon support to single file") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transport disconnect processing does a "wake pending tasks" at
various points.
Suppose an RPC Reply is being processed. The RPC task that Reply
goes with is waiting on the pending queue. If a disconnect wake-up
happens before reply processing is done, that reply, even if it is
good, is thrown away, and the RPC has to be sent again.
This window apparently does not exist for socket transports because
there is a lock held while a reply is being received which prevents
the wake-up call until after reply processing is done.
To resolve this, all RPC replies being processed on an RPC-over-RDMA
transport have to complete before pending tasks are awoken due to a
transport disconnect.
Callers that already hold the transport write lock may invoke
->ops->close directly. Others use a generic helper that schedules
a close when the write lock can be taken safely.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A bug is present in GDB which causes early string termination when
parsing variables. This has been reported [0], but we should ensure
that we can support at least basic printing of the core kernel strings.
For current gdb version (has been tested with 7.3 and 8.1), 'lx-version'
only prints one character.
(gdb) lx-version
L(gdb)
This can be fixed by casting 'linux_banner' as (char *).
(gdb) lx-version
Linux version 4.19.0-rc1+ (changbin@acer) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21 SMP Sat Sep 1 21:43:30 CST 2018
Since __sanitizer_cov_trace_const_cmp4 is marked as notrace, the
function called from __sanitizer_cov_trace_const_cmp4 shouldn't be
traceable either. ftrace_graph_caller() gets called every time func
write_comp_data() gets called if it isn't marked 'notrace'. This is the
backtrace from gdb:
#0 ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:179
#1 0xffffff8010201920 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:151
#2 0xffffff8010439714 in write_comp_data (type=5, arg1=0, arg2=0, ip=18446743524224276596) at ../kernel/kcov.c:116
#3 0xffffff8010439894 in __sanitizer_cov_trace_const_cmp4 (arg1=<optimized out>, arg2=<optimized out>) at ../kernel/kcov.c:188
#4 0xffffff8010201874 in prepare_ftrace_return (self_addr=18446743524226602768, parent=0xffffff801014b918, frame_pointer=18446743524223531344) at ./include/generated/atomic-instrumented.h:27
#5 0xffffff801020194c in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:182
Rework so that write_comp_data() that are called from
__sanitizer_cov_trace_*_cmp*() are marked as 'notrace'.
Commit 903e8ff86753 ("kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace")
missed to mark write_comp_data() as 'notrace'. When that patch was
created gcc-7 was used. In lib/Kconfig.debug
config KCOV_ENABLE_COMPARISONS
depends on $(cc-option,-fsanitize-coverage=trace-cmp)
That code path isn't hit with gcc-7. However, it were that with gcc-8.
Link: http://lkml.kernel.org/r/20181206143011.23719-1-anders.roxell@linaro.org Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Co-developed-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
load_script() simply truncates bprm->buf and this is very wrong if the
length of shebang string exceeds BINPRM_BUF_SIZE-2. This can silently
truncate i_arg or (worse) we can execute the wrong binary if buf[2:126]
happens to be the valid executable path.
Change load_script() to return ENOEXEC if it can't find '\n' or zero in
bprm->buf. Note that '\0' can come from either
prepare_binprm()->memset() or from kernel_read(), we do not care.
Link: http://lkml.kernel.org/r/20181112160931.GA28463@redhat.com Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Ben Woodard <woodard@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ep->ovflist is a secondary ready-list to temporarily store events
that might occur when doing sproc without holding the ep->wq.lock. This
accounts for every time we check for ready events and also send events
back to userspace; both callbacks, particularly the latter because of
copy_to_user, can account for a non-trivial time.
As such, the unlikely() check to see if the pointer is being used, seems
both misleading and sub-optimal. In fact, we go to an awful lot of
trouble to sync both lists, and populating the ovflist is far from an
uncommon scenario.
For example, profiling a concurrent epoll_wait(2) benchmark, with
CONFIG_PROFILE_ANNOTATED_BRANCHES shows that for a two threads a 33%
incorrect rate was seen; and when incrementally increasing the number of
epoll instances (which is used, for example for multiple queuing load
balancing models), up to a 90% incorrect rate was seen.
Similarly, by deleting the prediction, 3% throughput boost was seen
across incremental threads.
Link: http://lkml.kernel.org/r/20181108051006.18751-4-dave@stgolabs.net Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Jason Baron <jbaron@akamai.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on commit 401c636a0eeb ("kernel/hung_task.c: show all hung tasks
before panic"), we could get the call stack of hung task.
However, if the console loglevel is not high, we still can not see the
useful panic information in practice, and in most cases users don't set
console loglevel to high level.
This patch is to force console verbose before system panic, so that the
real useful information can be seen in the console, instead of being
like the following, which doesn't have hung task information.
INFO: task init:1 blocked for more than 120 seconds.
Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Kernel panic - not syncing: hung_task: blocked tasks
CPU: 2 PID: 479 Comm: khungtaskd Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
Call Trace:
dump_stack+0x4f/0x65
panic+0xde/0x231
watchdog+0x290/0x410
kthread+0x12c/0x150
ret_from_fork+0x35/0x40
reboot: panic mode set: p,w
Kernel Offset: 0x34000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A6015B675@SHSMSX101.ccr.corp.intel.com Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are three processing functions dealing with digital parameters,
__do_proc_dointvec/__do_proc_douintvec/__do_proc_doulongvec_minmax.
This patch deals with __do_proc_doulongvec_minmax, just as
__do_proc_dointvec does, adding a check for parameters 'left'. In
__do_proc_douintvec, its code implementation explicitly does not support
multiple inputs.
static int __do_proc_douintvec(...){
...
/*
* Arrays are not supported, keep this simple. *Do not* add
* support for them.
*/
if (vleft != 1) {
*lenp = 0;
return -EINVAL;
}
...
}
So, just __do_proc_doulongvec_minmax has the problem. And most use of
proc_doulongvec_minmax/proc_doulongvec_ms_jiffies_minmax just have one
parameter.
Link: http://lkml.kernel.org/r/1544081775-15720-1-git-send-email-cheng.lin130@zte.com.cn Signed-off-by: Cheng Lin <cheng.lin130@zte.com.cn> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
check_hung_uninterruptible_tasks() is currently calling rcu_lock_break()
for every 1024 threads. But check_hung_task() is very slow if printk()
was called, and is very fast otherwise.
If many threads within some 1024 threads called printk(), the RCU grace
period might be extended enough to trigger RCU stall warnings.
Therefore, calling rcu_lock_break() for every some fixed jiffies will be
safer.
Link: http://lkml.kernel.org/r/1544800658-11423-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SVE_PT_REGS_OFFSET is supposed to indicate the offset for skipping
over the ptrace NT_ARM_SVE header (struct user_sve_header) to the
start of the SVE register data proper.
However, currently SVE_PT_REGS_OFFSET is defined in terms of struct
sve_context, which is wrong: that structure describes the SVE
header in the signal frame, not in the ptrace regset.
This patch fixes the definition to use the ptrace header structure
struct user_sve_header instead.
By good fortune, the two structures are the same size anyway, so
there is no functional or ABI change.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
First correct the edge case to return the last element if we're
outside the range, rather than at the last element, so that
interpolation is not omitted for points between the two last entries in
the table.
Then correct the formula to perform linear interpolation based the two
points surrounding the read ADC value. The indices for temp are kept as
"hi" and "lo" to pair with the adc indices, but there's no requirement
that the temperature is provided in descendent order. mult_frac() is
used to prevent issues with overflowing the int.
Reverting commit 8ccb8cb1892b ("swim3: convert to blk-mq") resolves the
problem.
That commit added a struct blk_mq_tag_set to struct floppy_state and
initialized it with a blk_mq_init_sq_queue() call. Unfortunately, there
is a memset() in swim3_add_device() that subsequently clears the
floppy_state struct. That means fs->tag_set->ops is a NULL pointer, and
it gets dereferenced by blk_mq_free_rqs() which gets called in the
request_irq() error path. Move the memset() to fix this bug.
BTW, the request_irq() failure for the left mediabay floppy (fd1) is not
a regression. I don't know why it happens. The right media bay floppy
(fd0) works fine however.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 8ccb8cb1892b ("swim3: convert to blk-mq") Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MSI Enable bit in the MSI Capability (PCIe r4.0, sec 7.7.1.2) controls
whether a Function can request service using MSI.
i.MX6 Root Ports implement the MSI Capability and may use MSI to request
service for events like PME, hotplug, AER, etc. In addition, on i.MX6, the
MSI Enable bit controls delivery of MSI interrupts from components below
the Root Port.
Prior to f3fdfc4ac3a2 ("PCI: Remove host driver Kconfig selection of
CONFIG_PCIEPORTBUS"), enabling CONFIG_PCI_IMX6 automatically also enabled
CONFIG_PCIEPORTBUS, and when portdrv claimed the Root Ports, it set the MSI
Enable bit so it could use PME, hotplug, AER, etc. As a side effect, that
also enabled delivery of MSI interrupts from downstream components.
The imx6q-pcie driver itself does not depend on portdrv, so set MSI Enable
in imx6q-pcie so MSI from downstream components works even if nobody uses
MSI for the Root Port events.
Fixes: f3fdfc4ac3a2 ("PCI: Remove host driver Kconfig selection of CONFIG_PCIEPORTBUS") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Sven Van Asbroeck <TheSven73@googlemail.com> Tested-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Regmap would use device name to create debugfs entries. If the device
has multiple regmaps it is recommended to use name field in regmap_config.
Fix this by providing name to the regmap configs correctly.
Without this patch we would see below error on DB820c.
qcom-tsens 4a9000.thermal-sensor: Failed to create 4a9000.thermal-sensor
debugfs directory
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Amit Kucheria <amit.kucheria@linaro.org> Tested-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you have a CPU that fails to round up and then run 'btc' you'll end
up crashing in kdb becaue we dereferenced NULL. Let's add a check.
It's wise to also set the task to NULL when leaving the debugger so
that if we fail to round up on a later entry into the debugger we
won't backtrace a stale task.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
By defaul of-based thermal driver do not enable hwmon.
This patch does this explicitly, so that the temperature can be read
through the common hwmon sysfs.
When the block device is opened with FMODE_EXCL, ref_count is set to -1.
This value doesn't get reset when the device is closed which means the
device cannot be opened again. Fix this by checking for refcount <= 0
in the release method.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In probe_gdrom(), the buffer pointed by 'gd.cd_info' is allocated through
kzalloc() and is used to hold the information of the gdrom device. To
register and unregister the device, the pointer 'gd.cd_info' is passed to
the functions register_cdrom() and unregister_cdrom(), respectively.
However, this buffer is not freed after it is used, which can cause a
memory leak bug.
This patch simply frees the buffer 'gd.cd_info' in exit_gdrom() to fix the
above issue.
Inherently, swap device has many idle pages which are rare touched since
it was allocated. It is never problem if we use storage device as swap.
However, it's just waste for zram-swap.
This patchset supports zram idle page writeback feature.
* Admin can define what is idle page "no access since X time ago"
* Admin can define when zram should writeback them
* Admin can define when zram should stop writeback to prevent wearout
Details are in each patch's description.
This patch (of 7):
================================
WARNING: inconsistent lock state
4.19.0+ #390 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
zram_verify/2095 [HC0[0]:SC1[1]:HE1:SE0] takes: 00000000b1828693 (&(&zram->bitmap_lock)->rlock){+.?.}, at: put_entry_bdev+0x1e/0x50
{SOFTIRQ-ON-W} state was registered at:
_raw_spin_lock+0x2c/0x40
zram_make_request+0x755/0xdc9
generic_make_request+0x373/0x6a0
submit_bio+0x6c/0x140
__swap_writepage+0x3a8/0x480
shrink_page_list+0x1102/0x1a60
shrink_inactive_list+0x21b/0x3f0
shrink_node_memcg.constprop.99+0x4f8/0x7e0
shrink_node+0x7d/0x2f0
do_try_to_free_pages+0xe0/0x300
try_to_free_pages+0x116/0x2b0
__alloc_pages_slowpath+0x3f4/0xf80
__alloc_pages_nodemask+0x2a2/0x2f0
__handle_mm_fault+0x42e/0xb50
handle_mm_fault+0x55/0xb0
__do_page_fault+0x235/0x4b0
page_fault+0x1e/0x30
irq event stamp: 228412
hardirqs last enabled at (228412): [<ffffffff98245846>] __slab_free+0x3e6/0x600
hardirqs last disabled at (228411): [<ffffffff98245625>] __slab_free+0x1c5/0x600
softirqs last enabled at (228396): [<ffffffff98e0031e>] __do_softirq+0x31e/0x427
softirqs last disabled at (228403): [<ffffffff98072051>] irq_exit+0xd1/0xe0
other info that might help us debug this:
Possible unsafe locking scenario:
With writeback feature, zram_slot_free_notify could be called in softirq
context by end_swap_bio_read. However, bitmap_lock is not aware of that
so lockdep yell out:
With akpm's suggestion (i.e. bitmap operation is already atomic), we
could remove bitmap lock. It might fail to find a empty slot if serious
contention happens. However, it's not severe problem because huge page
writeback has already possiblity to fail if there is severe memory
pressure. Worst case is just keeping the incompressible in memory, not
storage.
The other problem is zram_slot_lock in zram_slot_slot_free_notify. To
make it safe is this patch introduces zram_slot_trylock where
zram_slot_free_notify uses it. Although it's rare to be contented, this
patch adds new debug stat "miss_free" to keep monitoring how often it
happens.
projects / thirdparty / kernel / stable.git / log
