This reverts commit 584cf613c24a4250d9be4819efc841aa2624d5b6.
Commit 584cf613c24a ("drm/i915/dp: Reject HBR3 when sink doesn't support
TPS4") introduced a blanket rejection of HBR3 link rate when the sink does
not support TPS4.
While this was intended to address instability observed on certain eDP
panels [1], there seem to be edp panels that do not follow the
specification. These eDP panels do not advertise TPS4 support, but require
HBR3 to operate at their fixed native resolution [2].
As a result, the change causes blank screens on such panels. Apparently,
Windows driver does not enforce this restriction, and the issue is not seen
there.
Therefore, revert the commit to restore functionality for such panels,
and align behaviour with Windows driver.
Jari Ruusu [Sat, 22 Nov 2025 07:28:00 +0000 (07:28 +0000)]
tty/vt: fix up incorrect backport to stable releases
Below is a patch for 6.12.58+ and 6.17.8+ stable branches only.
Upstream does not need this.
Signed-off-by: Jari Ruusu <jariruusu@protonmail.com> Fixes: da7e8b382396 ("tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[why]
1. With allow_0_dtb_clk enabled, the time required to latch DTBCLK to 600 MHz
depends on the SMU. If DTBCLK is not latched to 600 MHz before set_mode completes,
gating DTBCLK causes the DP2 sink to lose its clock source.
2. The existing DTBCLK gating sequence ungates DTBCLK based on both pix_clk and ref_dtbclk,
but gates DTBCLK when either pix_clk or ref_dtbclk is zero.
pix_clk can be zero outside the set_mode sequence before DTBCLK is properly latched,
which can lead to DTBCLK being gated by mistake.
[how]
Consider both pixel_clk and ref_dtbclk when determining when it is safe to gate DTBCLK;
this is more accurate.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4701 Fixes: 5949e7c4890c ("drm/amd/display: Enable Dynamic DTBCLK Switch") Reviewed-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d04eb0c402780ca037b62a6aecf23b863545ebca) Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix inverted WARN_ON_ONCE condition that prevented normal address
removal counter updates. The current code only executes decrement
logic when the counter is already 0 (abnormal state), while
normal removals (counter > 0) are ignored.
CPU: 1 UID: 0 PID: 1300113 Comm: xfs_scrub Not tainted 6.18.0-rc4-djwx #rc4 PREEMPT(lazy) 3d744dd94e92690f00a04398d2bd8631dcef1954
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-4.module+el8.8.0+21164+ed375313 04/01/2014
==================================================================
On further analysis, I realized that the second parameter to min() is
not correct. xfs_ifork::if_bytes is the size of the xfs_ifork::if_data
buffer. if_bytes can be smaller than the data fork size because:
(a) the forkoff code tries to keep the data area as large as possible
(b) for symbolic links, if_bytes is the ondisk file size + 1
(c) forkoff is always a multiple of 8.
Case in point: for a single-byte symlink target, forkoff will be
8 but the buffer will only be 2 bytes long.
In other words, the logic here is wrong and we walk off the end of the
incore buffer. Fix that.
Cc: stable@vger.kernel.org # v6.10 Fixes: 2651923d8d8db0 ("xfs: online repair of symbolic links") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changes modernizes the code by aligning it with current kernel best
practices. It improves code clarity and consistency, as strncpy is deprecated
as explained in Documentation/process/deprecated.rst. This change does
not alter the functionality or introduce any behavioral changes.
Suggested-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Marcelo Moreira <marcelomoreira1905@gmail.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Stable-dep-of: 678e1cc2f482 ("xfs: fix out of bounds memory read error in symlink repair") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable Panel Replay on MST links until it's properly implemented. For
instance the required VSC SDP is not programmed on MST and FEC is not
enabled if Panel Replay is enabled.
Currently we are ignoriong drm_dp_dpcd_read return values when reading PSR
and Panel Replay capability DPCD register. Rework intel_psr_dpcd a bit to
take care of checking the return value.
smb: client: fix incomplete backport in cfids_invalidation_worker()
The previous commit bdb596ceb4b7 ("smb: client: fix potential UAF in
smb2_close_cached_fid()") was an incomplete backport and missed one
kref_put() call in cfids_invalidation_worker() that should have been
converted to close_cached_dir().
On PF passthrough environment, after hibernate and then resume, coralgemm
will cause gpu page fault.
Mode1 reset happens during hibernate, but partition mode is not restored
on resume, register mmCP_HYP_XCP_CTL and mmCP_PSP_XCP_CTL is not right
after resume. When CP access the MQD BO, wrong stride size is used,
this will cause out of bound access on the MQD BO, resulting page fault.
The fix is to ensure gfx_v9_4_3_switch_compute_partition() is called
when resume from a hibernation.
KFD resume is called separately during a reset recovery or resume from
suspend sequence. Hence it's not required to be called as part of
partition switch.
Signed-off-by: Samuel Zhang <guoqing.zhang@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5d1b32cfe4a676fe552416cb5ae847b215463a1a) Signed-off-by: Sasha Levin <sashal@kernel.org>
If we are logging a new name make sure our inode has the runtime flag
BTRFS_INODE_COPY_EVERYTHING set so that at btrfs_log_inode() we will find
new inode refs/extrefs in the subvolume tree and copy them into the log
tree.
We are currently doing it when adding a new link but we are missing it
when renaming.
An example where this makes a new name not persisted:
1) create symlink with name foo in directory A
2) fsync directory A, which persists the symlink
3) rename the symlink from foo to bar
4) fsync directory A to persist the new symlink name
Step 4 isn't working correctly as it's not logging the new name and also
leaving the old inode ref in the log tree, so after a power failure the
symlink still has the old name of "foo". This is because when we first
fsync directoy A we log the symlink's inode (as it's a new entry) and at
btrfs_log_inode() we set the log mode to LOG_INODE_ALL and then because
we are using that mode and the inode has the runtime flag
BTRFS_INODE_NEEDS_FULL_SYNC set, we clear that flag as well as the flag
BTRFS_INODE_COPY_EVERYTHING. That means the next time we log the inode,
during the rename through the call to btrfs_log_new_name() (calling
btrfs_log_inode_parent() and then btrfs_log_inode()), we will not search
the subvolume tree for new refs/extrefs and jump directory to the
'log_extents' label.
Fix this by making sure we set BTRFS_INODE_COPY_EVERYTHING on an inode
when we are about to log a new name. A test case for fstests will follow
soon.
Reported-by: Vyacheslav Kovalevsky <slava.kovalevskiy.2014@gmail.com> Link: https://lore.kernel.org/linux-btrfs/ac949c74-90c2-4b9a-b7fd-1ffc5c3175c7@gmail.com/ Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The help message incorrectly listed '-t' as the short option for
--threads, but the actual getopt_long configuration uses '-e'.
This mismatch can confuse users and lead to incorrect command-line
usage. This patch updates the usage string to correctly show:
"-e, --threads NRTHR"
to match the implementation.
Note: checkpatch.pl reports a false-positive spelling warning on
'Run', which is intentional.
Make knav_dma_open_channel consistently return NULL on error instead
of ERR_PTR. Currently the header include/linux/soc/ti/knav_dma.h
returns NULL when the driver is disabled, but the driver
implementation does not even return NULL or ERR_PTR on failure,
causing inconsistency in the users. This results in a crash in
netcp_free_navigator_resources as followed (trimmed):
Unhandled fault: alignment exception (0x221) at 0xfffffff2
[fffffff2] *pgd=80000800207003, *pmd=82ffda003, *pte=00000000
Internal error: : 221 [#1] SMP ARM
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc7 #1 NONE
Hardware name: Keystone
PC is at knav_dma_close_channel+0x30/0x19c
LR is at netcp_free_navigator_resources+0x2c/0x28c
[... TRIM...]
Call trace:
knav_dma_close_channel from netcp_free_navigator_resources+0x2c/0x28c
netcp_free_navigator_resources from netcp_ndo_open+0x430/0x46c
netcp_ndo_open from __dev_open+0x114/0x29c
__dev_open from __dev_change_flags+0x190/0x208
__dev_change_flags from netif_change_flags+0x1c/0x58
netif_change_flags from dev_change_flags+0x38/0xa0
dev_change_flags from ip_auto_config+0x2c4/0x11f0
ip_auto_config from do_one_initcall+0x58/0x200
do_one_initcall from kernel_init_freeable+0x1cc/0x238
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x38
[... TRIM...]
Standardize the error handling by making the function return NULL on
all error conditions. The API is used in just the netcp_core.c so the
impact is limited.
Note, this change, in effect reverts commit 5b6cb43b4d62 ("net:
ethernet: ti: netcp_core: return error while dma channel open issue"),
but provides a less error prone implementation.
Suggested-by: Simon Horman <horms@kernel.org> Suggested-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20251103162811.3730055-1-nm@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to UFS specifications, the power-off sequence for a UFS device
includes:
- Sending an SSU command with Power_Condition=3 and await a response.
- Asserting RST_N low.
- Turning off REF_CLK.
- Turning off VCC.
- Turning off VCCQ/VCCQ2.
As part of ufs shutdown, after the SSU command completion, asserting
hardware reset (HWRST) triggers the device firmware to wake up and
execute its reset routine. This routine initializes hardware blocks and
takes a few milliseconds to complete. During this time, the ICCQ draws a
large current.
This large ICCQ current may cause issues for the regulator which is
supplying power to UFS, because the turn off request from UFS driver to
the regulator framework will be immediately followed by low power
mode(LPM) request by regulator framework. This is done by framework
because UFS which is the only client is requesting for disable. So if
the rail is still in the process of shutting down while ICCQ exceeds LPM
current thresholds, and LPM mode is activated in hardware during this
state, it may trigger an overcurrent protection (OCP) fault in the
regulator.
To prevent this, a 10ms delay is added after asserting HWRST. This
allows the reset operation to complete while power rails remain active
and in high-power mode.
Currently there is no way for Host to query whether the reset is
completed or not and hence this the delay is based on experiments with
Qualcomm UFS controllers across multiple UFS vendors.
Signed-off-by: Nitin Rawat <nitin.rawat@oss.qualcomm.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Link: https://patch.msgid.link/20251012173828.9880-1-nitin.rawat@oss.qualcomm.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 8b3a087f7f65 ("ALSA: usb-audio: Unify virtual type units type to
UAC3 values") usb-audio is using UAC3_CLOCK_SOURCE instead of
bDescriptorSubtype, later refactored with e0ccdef9265 ("ALSA: usb-audio:
Clean up check_input_term()") into parse_term_uac2_clock_source().
This breaks the clock source selection for at least my
1397:0003 BEHRINGER International GmbH FCA610 Pro.
Fix by using UAC2_CLOCK_SOURCE in parse_term_uac2_clock_source().
If user provides a large value (such as 0x80) for parameter
prefetch_mem_region_instance in vm_bind ioctl, it will cause
BIT(prefetch_region) overflow as below:
"
------------[ cut here ]------------
UBSAN: shift-out-of-bounds in drivers/gpu/drm/xe/xe_vm.c:3414:7
shift exponent 128 is too large for 64-bit type 'long unsigned int'
CPU: 8 UID: 0 PID: 53120 Comm: xe_exec_system_ Tainted: G W 6.18.0-rc1-lgci-xe-kernel+ #200 PREEMPT(voluntary)
Tainted: [W]=WARN
Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 0812 02/24/2023
Call Trace:
<TASK>
dump_stack_lvl+0xa0/0xc0
dump_stack+0x10/0x20
ubsan_epilogue+0x9/0x40
__ubsan_handle_shift_out_of_bounds+0x10e/0x170
? mutex_unlock+0x12/0x20
xe_vm_bind_ioctl.cold+0x20/0x3c [xe]
...
"
Fix it by validating prefetch_region before the BIT() usage.
v2: Add Closes and Cc stable kernels. (Matt)
Reported-by: Koen Koning <koen.koning@intel.com> Reported-by: Peter Senna Tschudin <peter.senna@linux.intel.com> Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs") Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/6478 Cc: <stable@vger.kernel.org> # v6.8+ Reviewed-by: Matthew Auld <matthew.auld@intel.com> Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Link: https://patch.msgid.link/20251112181005.2120521-2-shuicheng.lin@intel.com
(cherry picked from commit 8f565bdd14eec5611cc041dba4650e42ccdf71d9) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit d52dea485cd3c98cfeeb474cf66cf95df2ab142f) Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix bug where make nconfig doesn't initialize the default locale, which
causes ncurses menu borders to be displayed incorrectly (lqqqqk) in
UTF-8 terminals that don't support VT100 ACS by default, such as PuTTY.
Fix bug where make menuconfig doesn't initialize the default locale, which
causes ncurses menu borders to be displayed incorrectly (lqqqqk) in
UTF-8 terminals that don't support VT100 ACS by default, such as PuTTY.
When a netdev issues a RX async resync request for a TLS connection,
the TLS module handles it by logging record headers and attempting to
match them to the tcp_sn provided by the device. If a match is found,
the TLS module approves the tcp_sn for resynchronization.
While waiting for a device response, the TLS module also increments
rcd_delta each time a new TLS record is received, tracking the distance
from the original resync request.
However, if the device response is delayed or fails (e.g due to
unstable connection and device getting out of tracking, hardware
errors, resource exhaustion etc.), the TLS module keeps logging and
incrementing, which can lead to a WARN() when rcd_delta exceeds the
threshold.
To address this, introduce tls_offload_rx_resync_async_request_cancel()
to explicitly cancel resync requests when a device response failure is
detected. Call this helper also as a final safeguard when rcd_delta
crosses its threshold, as reaching this point implies that earlier
cancellation did not occur.
Update tls_offload_rx_resync_async_request_start() and
tls_offload_rx_resync_async_request_end() to get a struct
tls_offload_resync_async parameter directly, rather than
extracting it from struct sock.
This change aligns the function signatures with the upcoming
tls_offload_rx_resync_async_request_cancel() helper, which
will be introduced in a subsequent patch.
In bareudp.sh, this script uses /bin/sh and it will load another lib.sh
BASH script at the very beginning.
But on some operating systems like Ubuntu, /bin/sh is actually pointed to
DASH, thus it will try to run BASH commands with DASH and consequently
leads to syntax issues:
# ./bareudp.sh: 4: ./lib.sh: Bad substitution
# ./bareudp.sh: 5: ./lib.sh: source: not found
# ./bareudp.sh: 24: ./lib.sh: Syntax error: "(" unexpected
Fix this by explicitly using BASH for bareudp.sh. This fixes test
execution failures on systems where /bin/sh is not BASH.
In very rare cases, DFS mounts could end up with SMB sessions without
any IPC connections. These mounts are only possible when having
unexpired cached DFS referrals, hence not requiring any IPC
connections during the mount process.
Try to establish those missing IPC connections when refreshing DFS
referrals. If the server is still rejecting it, then simply ignore
and leave expired cached DFS referral for any potential DFS failovers.
Reported-by: Jay Shin <jaeshin@redhat.com> Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org> Cc: David Howells <dhowells@redhat.com> Cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix warning caused from declaration under a case label. The proper way
is to declare variable at the beginning of the function. The warning
came from running clang using LLVM=1; and is as follows:
-test_cachestat.c:260:3: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
260 | char *map = mmap(NULL, filesize, PROT_READ | PROT_WRITE,
|
Link: https://lore.kernel.org/r/20250929115405.25695-2-sidharthseela@gmail.com Signed-off-by: Sidharth Seela <sidharthseela@gmail.com> Reviewed-by: SeongJae Park <sj@kernel.org> Reviewed-by: wang lian <lianux.mm@gmail.com> Reviewed-by: Dev Jain <dev.jain@arm.com> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Acked-by: Nhat Pham <nphamcs@gmail.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
WildcatLake (WCL) is a variant of PantherLake (PTL) and shares the same
uncore PMU features with PTL. Therefore, directly reuse Pantherlake's
uncore PMU enabling code for WildcatLake.
The quirk for Victus 15-fa1xxx wasn't working on Victus 15-fa1031nt due to a different board id. This patch enables the existing quirk for the board id 8BC8.
Tested on HP Victus 15-fa1031nt (MB 8C2D). The LED behaviour works as intended.
Fix this regression by making scsi_host_busy() check whether the SCSI
host tag set has already been initialized. tag_set->ops is set by
scsi_mq_setup_tags() just before blk_mq_alloc_tag_set() is called. This
fix is based on the assumption that scsi_host_busy() and
scsi_mq_setup_tags() calls are serialized. This is the case in the UFS
driver.
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com> Closes: https://lore.kernel.org/linux-block/pnezafputodmqlpumwfbn644ohjybouveehcjhz2hmhtcf2rka@sdhoiivync4y/ Cc: Ming Lei <ming.lei@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://patch.msgid.link/20251007214800.1678255-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since msm_vma_job_free() is called directly from the ioctl, this looks
like an error path cleanup issue. Which I think results from
prealloc_cleanup() called without a preceding successful
prealloc_allocate() call. So handle that case better.
Reported-by: Connor Abbott <cwabbott0@gmail.com> Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/678677/
Message-ID: <20251006153542.419998-1-robin.clark@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sched_ext code calls queue_balance_callback() during enqueue_task()
to defer operations that drop multiple locks until we can unpin them.
The call assumes that the rq lock is held until the callbacks are
invoked, and the pending callbacks will not be visible to any other
threads. This is enforced by a WARN_ON_ONCE() in rq_pin_lock().
However, balance_one() may actually drop the lock during a BPF dispatch
call. Another thread may win the race to get the rq lock and see the
pending callback. To avoid this, sched_ext must only queue the callback
after the dispatch calls have completed.
On systems with >4096 CPUs, scx_kick_cpus_pnt_seqs allocation fails during
boot because it exceeds the 32,768 byte percpu allocator limit.
Restructure to use DEFINE_PER_CPU() for the per-CPU pointers, with each CPU
pointing to its own kvzalloc'd array. Move allocation from boot time to
scx_enable() and free in scx_disable(), so the O(nr_cpu_ids^2) memory is only
consumed when sched_ext is active.
Use RCU to guard against racing with free. Arrays are freed via call_rcu()
and kick_cpus_irq_workfn() uses rcu_dereference_bh() with a NULL check.
While at it, rename to scx_kick_pseqs for brevity and update comments to
clarify these are pick_task sequence numbers.
v2: RCU protect scx_kick_seqs to manage kick_cpus_irq_workfn() racing
against disable as per Andrea.
v3: Fix bugs notcied by Andrea.
Reported-by: Phil Auld <pauld@redhat.com> Link: http://lkml.kernel.org/r/20251007133523.GA93086@pauld.westford.csb Cc: Andrea Righi <arighi@nvidia.com> Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com> Reviewed-by: Phil Auld <pauld@redhat.com> Reviewed-by: Andrea Righi <arighi@nvidia.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 69896119dc9d ("MIPS: vdso: Switch to generic storage
implementation") switches to a generic vdso storage, which increases
the number of data pages from 1 to 4. But there is only one page
reserved, which causes segementation faults depending where the VDSO
area is randomized to. To fix this use the same size of reservation
and allocation of the VDSO data pages.
Fixes: 69896119dc9d ("MIPS: vdso: Switch to generic storage implementation") Reviewed-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
tk_aux_sysfs_init() returns immediately on error during the auxiliary clock
initialization loop without cleaning up previously allocated kobjects and
sysfs groups.
If kobject_create_and_add() or sysfs_create_group() fails during loop
iteration, the parent kobjects (tko and auxo) and any previously created
child kobjects are leaked.
Fix this by adding proper error handling with goto labels to ensure all
allocated resources are cleaned up on failure. kobject_put() on the
parent kobjects will handle cleanup of their children.
Fixes: 7b95663a3d96 ("timekeeping: Provide interface to control auxiliary clocks") Signed-off-by: Malaya Kumar Rout <mrout@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://patch.msgid.link/20251120150213.246777-1-mrout@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
During connect(), acting on a signal/timeout by disconnecting an already
established socket leads to several issues:
1. connect() invoking vsock_transport_cancel_pkt() ->
virtio_transport_purge_skbs() may race with sendmsg() invoking
virtio_transport_get_credit(). This results in a permanently elevated
`vvs->bytes_unsent`. Which, in turn, confuses the SOCK_LINGER handling.
2. connect() resetting a connected socket's state may race with socket
being placed in a sockmap. A disconnected socket remaining in a sockmap
breaks sockmap's assumptions. And gives rise to WARNs.
3. connect() transitioning SS_CONNECTED -> SS_UNCONNECTED allows for a
transport change/drop after TCP_ESTABLISHED. Which poses a problem for
any simultaneous sendmsg() or connect() and may result in a
use-after-free/null-ptr-deref.
Do not disconnect socket on signal/timeout. Keep the logic for unconnected
sockets: they don't linger, can't be placed in a sockmap, are rejected by
sendmsg().
Currently cpu-clock event always returns 0 count, e.g.,
perf stat -e cpu-clock -- sleep 1
Performance counter stats for 'sleep 1':
0 cpu-clock # 0.000 CPUs utilized
1.002308394 seconds time elapsed
The root cause is the commit 'bc4394e5e79c ("perf: Fix the throttle
error of some clock events")' adds PERF_EF_UPDATE flag check before
calling cpu_clock_event_update() to update the count, however the
PERF_EF_UPDATE flag is never set when the cpu-clock event is stopped in
counting mode (pmu->dev() -> cpu_clock_event_del() ->
cpu_clock_event_stop()). This leads to the cpu-clock event count is
never updated.
To fix this issue, force to set PERF_EF_UPDATE flag for cpu-clock event
just like what task-clock does.
Fixes: bc4394e5e79c ("perf: Fix the throttle error of some clock events") Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Ian Rogers <irogers@google.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://patch.msgid.link/20251112080526.3971392-1-dapeng1.mi@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Add proper cleanup of ctx->source and fc->source to the
cifs_parse_mount_err error handler. This ensures that memory allocated
for the source strings is correctly freed on all error paths, matching
the cleanup already performed in the success path by
smb3_cleanup_fs_context_contents().
Pointers are also set to NULL after freeing to prevent potential
double-free issues.
This change fixes a memory leak originally detected by syzbot. The
leak occurred when processing Opt_source mount options if an error
happened after ctx->source and fc->source were successfully
allocated but before the function completed.
The specific leak sequence was:
1. ctx->source = smb3_fs_context_fullpath(ctx, '/') allocates memory
2. fc->source = kstrdup(ctx->source, GFP_KERNEL) allocates more memory
3. A subsequent error jumps to cifs_parse_mount_err
4. The old error handler freed passwords but not the source strings,
causing the memory to leak.
This issue was not addressed by commit e8c73eb7db0a ("cifs: client:
fix memory leak in smb3_fs_context_parse_param"), which only fixed
leaks from repeated fsconfig() calls but not this error path.
Patch updated with minor change suggested by kernel test robot
Reported-by: syzbot+87be6809ed9bf6d718e3@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=87be6809ed9bf6d718e3 Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Reviewed-by: David Howells <dhowells@redhat.com> Signed-off-by: Shaurya Rane <ssrane_b23@ee.vjti.ac.in> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kernel UAPI headers already contain fixed-width integer types, there
is no need to rely on the libc types. There may not be a libc available
or the libc may not provides the <stdint.h>, like for example on nolibc.
This also aligns the header with the rest of the LoongArch UAPI headers.
Fixes: 803b0fc5c3f2 ("LoongArch: Add process management") Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") the
new function report_idle_softirq() was created by breaking code out of the
existing can_stop_idle_tick() for kernels v5.18 and newer.
In doing so, the code essentially went from this form:
if (A) {
static int ratelimit;
if (ratelimit < 10 && !C && A&D) {
pr_warn("NOHZ tick-stop error: ...");
ratelimit++;
}
return false;
}
to a new function:
static bool report_idle_softirq(void)
{
static int ratelimit;
if (likely(!A))
return false;
if (ratelimit < 10)
return false;
...
pr_warn("NOHZ tick-stop error: local softirq work is pending, handler #%02x!!!\n",
pending);
ratelimit++;
return true;
}
commit a7e282c77785 ("tick/rcu: Fix bogus ratelimit condition") realized
ratelimit was essentially set to zero instead of ten, and hence *no*
softirq pending messages would ever be issued, but "fixed" it as:
- if (ratelimit < 10)
+ if (ratelimit >= 10)
return false;
However, this fix introduced another issue:
When ratelimit is greater than or equal 10, even if A is true, it will
directly return false. While ratelimit in the original code was only used
to control printing and will not affect the return value.
Restore the original logic and restrict ratelimit to control the printk and
not the return value.
Fixes: 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") Fixes: a7e282c77785 ("tick/rcu: Fix bogus ratelimit condition") Signed-off-by: Wen Yang <wen.yang@linux.dev> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://patch.msgid.link/20251119174525.29470-1-wen.yang@linux.dev Signed-off-by: Sasha Levin <sashal@kernel.org>
Pause, Asym_Pause and Autoneg bits are not set when pl->supported is
initialized, so these link modes will not work for the fixed-link. This
leads to a TCP performance degradation issue observed on the i.MX943
platform.
The switch CPU port of i.MX943 is connected to an ENETC MAC, this link
is a fixed link and the link speed is 2.5Gbps. And one of the switch
user ports is the RGMII interface, and its link speed is 1Gbps. If the
flow-control of the fixed link is not enabled, we can easily observe
the iperf performance of TCP packets is very low. Because the inbound
rate on the CPU port is greater than the outbound rate on the user port,
the switch is prone to congestion, leading to the loss of some TCP
packets and requiring multiple retransmissions.
Solving this problem should be as simple as setting the Asym_Pause and
Pause bits. The reason why the Autoneg bit needs to be set, Russell
has gave a very good explanation in the thread [1], see below.
"As the advertising and lp_advertising bitmasks have to be non-empty,
and the swphy reports aneg capable, aneg complete, and AN enabled, then
for consistency with that state, Autoneg should be set. This is how it
was prior to the blamed commit."
With the final call to fput() on a file descriptor, the release action
may be deferred and scheduled on a work queue. The reference count of
that descriptor is still zero and it must not be used. It's possible
that a GPIO change, we want to notify the user-space about, happens
AFTER the reference count on the file descriptor associated with the
character device went down to zero but BEFORE the .release() callback
was called from the workqueue and so BEFORE we unregistered from the
notifier.
Using the regular get_file() routine in this situation triggers the
following warning:
struct file::f_count incremented from zero; use-after-free condition present!
So use the get_file_active() variant that will return NULL on file
descriptors that have been or are being released.
Fixes: 40b7c49950bd ("gpio: cdev: put emitting the line state events on a workqueue") Reported-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Closes: https://lore.kernel.org/all/5d605f7fc99456804911403102a4fe999a14cc85.camel@siemens.com/ Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Link: https://lore.kernel.org/r/20251117-gpio-cdev-get-file-v1-1-28a16b5985b8@linaro.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Miao Wang reported a bug of SO_PEEK_OFF on AF_UNIX SOCK_STREAM
socket.
The unexpected behaviour is triggered when the peek offset is
larger than the recv queue and the thread is unblocked by new
data.
Let's assume a socket which has "aaaa" in the recv queue and
the peek offset is 4.
First, unix_stream_read_generic() reads the offset 4 and skips
the skb(s) of "aaaa" with the code below:
skip = max(sk_peek_offset(sk, flags), 0); /* @skip is 4. */
do {
...
while (skip >= unix_skb_len(skb)) {
skip -= unix_skb_len(skb);
...
skb = skb_peek_next(skb, &sk->sk_receive_queue);
if (!skb)
goto again; /* @skip is 0. */
}
The thread jumps to the 'again' label and goes to sleep since
new data has not arrived yet.
Later, new data "bbbb" unblocks the thread, and the thread jumps
to the 'redo:' label to restart the entire process from the first
skb in the recv queue.
do {
...
redo:
...
last = skb = skb_peek(&sk->sk_receive_queue);
...
again:
if (skb == NULL) {
...
timeo = unix_stream_data_wait(sk, timeo, last,
last_len, freezable);
...
goto redo; /* @skip is 0 !! */
However, the peek offset is not reset in the path.
If the buffer size is 8, recv() will return "aaaabbbb" without
skipping any data, and the final offset will be 12 (the original
offset 4 + peeked skbs' length 8).
After sleeping in unix_stream_read_generic(), we have to fetch the
peek offset again.
Let's move the redo label before mutex_lock(&u->iolock).
Fixes: 9f389e35674f ("af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag") Reported-by: Miao Wang <shankerwangmiao@gmail.com> Closes: https://lore.kernel.org/netdev/3B969F90-F51F-4B9D-AB1A-994D9A54D460@gmail.com/ Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com> Link: https://patch.msgid.link/20251117174740.3684604-2-kuniyu@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mlx5_irq_alloc() function can inadvertently free the entire rmap
and end up in a crash[1] when the other threads tries to access this,
when request_irq() fails due to exhausted IRQ vectors. This commit
modifies the cleanup to remove only the specific IRQ mapping that was
just added.
This prevents removal of other valid mappings and ensures precise
cleanup of the failed IRQ allocation's associated glue object.
Note: This error is observed when both fwctl and rds configs are enabled.
[1]
mlx5_core 0000:05:00.0: Successfully registered panic handler for port 1
mlx5_core 0000:05:00.0: mlx5_irq_alloc:293:(pid 66740): Failed to
request irq. err = -28
infiniband mlx5_0: mlx5_ib_test_wc:290:(pid 66740): Error -28 while
trying to test write-combining support
mlx5_core 0000:05:00.0: Successfully unregistered panic handler for port 1
mlx5_core 0000:06:00.0: Successfully registered panic handler for port 1
mlx5_core 0000:06:00.0: mlx5_irq_alloc:293:(pid 66740): Failed to
request irq. err = -28
infiniband mlx5_0: mlx5_ib_test_wc:290:(pid 66740): Error -28 while
trying to test write-combining support
mlx5_core 0000:06:00.0: Successfully unregistered panic handler for port 1
mlx5_core 0000:03:00.0: mlx5_irq_alloc:293:(pid 28895): Failed to
request irq. err = -28
mlx5_core 0000:05:00.0: mlx5_irq_alloc:293:(pid 28895): Failed to
request irq. err = -28
general protection fault, probably for non-canonical address
0xe277a58fde16f291: 0000 [#1] SMP NOPTI
The function devl_rate_nodes_destroy is documented to "Unset parent for
all rate objects". However, it was only calling the driver-specific
`rate_leaf_parent_set` or `rate_node_parent_set` ops and decrementing
the parent's refcount, without actually setting the
`devlink_rate->parent` pointer to NULL.
This leaves a dangling pointer in the `devlink_rate` struct, which cause
refcount error in netdevsim[1] and mlx5[2]. In addition, this is
inconsistent with the behavior of `devlink_nl_rate_parent_node_set`,
where the parent pointer is correctly cleared.
This patch fixes the issue by explicitly setting `devlink_rate->parent`
to NULL after notifying the driver, thus fulfilling the function's
documented behavior for all rate objects.
[1]
repro steps:
echo 1 > /sys/bus/netdevsim/new_device
devlink dev eswitch set netdevsim/netdevsim1 mode switchdev
echo 1 > /sys/bus/netdevsim/devices/netdevsim1/sriov_numvfs
devlink port function rate add netdevsim/netdevsim1/test_node
devlink port function rate set netdevsim/netdevsim1/128 parent test_node
echo 1 > /sys/bus/netdevsim/del_device
[2]
devlink dev eswitch set pci/0000:08:00.0 mode switchdev
devlink port add pci/0000:08:00.0 flavour pcisf pfnum 0 sfnum 1000
devlink port function rate add pci/0000:08:00.0/group1
devlink port function rate set pci/0000:08:00.0/32768 parent group1
modprobe -r mlx5_ib mlx5_fwctl mlx5_core
s32_pmx_gpio_request_enable() does not initialize the newly-allocated
gpio_pin_config::list before adding it to s32_pinctrl::gpio_configs.
This could result in a linked list corruption.
Initialize the new list_head with INIT_LIST_HEAD() to fix this.
s32_pinctrl_desc is allocated with devm_kmalloc(), but not all of its
fields are initialized. Notably, num_custom_params is used in
pinconf_generic_parse_dt_config(), resulting in intermittent allocation
errors, such as the following splat when probing i2c-imx:
This results in later parse failures that can cause issues in dependent
drivers:
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
[...]
pca953x 0-0022: failed writing register: -6
i2c i2c-0: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
i2c i2c-1: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
i2c i2c-2: IMX I2C adapter registered
Fix this by initializing s32_pinctrl_desc with devm_kzalloc() instead of
devm_kmalloc() in s32_pinctrl_probe(), which sets the previously
uninitialized fields to zero.
Fixes: fd84aaa8173d ("pinctrl: add NXP S32 SoC family support") Signed-off-by: Jared Kangas <jkangas@redhat.com> Tested-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Improve the cleanup on releasing PTP resources in error path.
The error case might happen either at the driver probe and PTP
feature initialization or on PTP restart (errors in reset handling, NVM
update etc). In both cases, calls to PF PTP cleanup (ice_ptp_cleanup_pf
function) and 'ps_lock' mutex deinitialization were missed.
Additionally, ptp clock was not unregistered in the latter case.
Keep PTP state as 'uninitialized' on init to distinguish between error
scenarios and to avoid resource release duplication at driver removal.
The consequence of missing ice_ptp_cleanup_pf call is the following call
trace dumped when ice_adapter object is freed (port list is not empty,
as it is required at this stage):
Fixes: e800654e85b5 ("ice: Use ice_adapter for PTP shared data instead of auxdev") Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current gu2host handler registered as MSI-X vector 0 and as per bspec for
a msix vector 0 interrupt, the driver must check the legacy registers
190008(TILE_INT_REG), 190060h (GT INTR Identity Reg 0) and other registers
mentioned in "Interrupt Service Routine Pseudocode" otherwise it will block
the next interrupts. To overcome this issue replacing guc2host handler
with legacy xe_irq_handler.
Fixes: da889070be7b2 ("drm/xe/irq: Separate MSI and MSI-X flows")
Bspec: 62357 Signed-off-by: Venkata Ramana Nayana <venkata.ramana.nayana@intel.com> Reviewed-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com> Link: https://patch.msgid.link/20251107083141.2080189-1-venkata.ramana.nayana@intel.com Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit c34a14bce7090862ebe5a64abe8d85df75e62737) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MOCS kunit test calls KUNIT_ASSERT_TRUE_MSG() with a condition of
'true;' this prevents the assertion from ever failing. Replace
KUNIT_ASSERT_TRUE_MSG with KUNIT_FAIL_AND_ABORT to get the intended
failure behavior in cases where forcewake was not acquired successfully.
Fixes: 51c0ee84e4dc ("drm/xe/tests/mocs: Hold XE_FORCEWAKE_ALL for LNCF regs") Cc: Tejas Upadhyay <tejas.upadhyay@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com> Link: https://patch.msgid.link/20251113234038.2256106-2-matthew.d.roper@intel.com Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 9be4f0f687048ba77428ceca11994676736507b7) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On PTL, no combo PHY is connected to PORT B. However, PORT B can
still be used for Type-C and will utilize the C20 PHY for eDP
over Type-C. In such configurations, VBTs also enumerate PORT B.
This leads to issues where PORT B is incorrectly identified as using the
C10 PHY, due to the assumption that returning true for PORT B in
intel_encoder_is_c10phy() would not cause problems.
From PTL's perspective, only PORT A/PHY A uses the C10 PHY.
Update the helper intel_encoder_is_c10phy() to return true only for
PORT A/PHY on PTL.
v2: Change the condition code style for ptl/wcl
Bspec: 72571,73944 Fixes: 9d10de78a37f ("drm/i915/wcl: C10 phy connected to port A and B") Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com> Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com> Link: https://lore.kernel.org/r/20250922150317.2334680-4-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 8147f7a1c083fd565fb958824f7c552de3b2dc46) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We will need to differentiate between WCL and PTL in
intel_encoder_is_c10phy(). Since WCL and PTL use the same display
architecture, let's define WCL as a subplatform of PTL to allow the
differentiation.
v2: Update commit message and reorder wcl define (Gustavo)
Fixes: 3c0f211bc8fc ("drm/xe: Add Wildcat Lake device IDs to PTL list") Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com> Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com> Link: https://lore.kernel.org/r/20250922150317.2334680-3-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 4dfaae643e59cf3ab71b88689dce1b874f036f00) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo added Fixes tag when porting it to fixes] Signed-off-by: Sasha Levin <sashal@kernel.org>
To form the WCL platform as a subplatform of PTL in definition,
WCL pci ids are splited into saparate group from PTL.
So update the pciidlist struct to cover all the pci ids.
v2:
- Squash wcl description in single patch for display and xe.(jani,gustavo)
Fixes: 3c0f211bc8fc ("drm/xe: Add Wildcat Lake device IDs to PTL list") Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com> Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com> Link: https://lore.kernel.org/r/20250922150317.2334680-2-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 32620e176443bf23ec81bfe8f177c6721a904864) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo added the Fixes tag when porting it to fixes] Signed-off-by: Sasha Levin <sashal@kernel.org>
The loops in 'qede_tpa_cont()' and 'qede_tpa_end()', iterate
over 'cqe->len_list[]' using only a zero-length terminator as
the stopping condition. If the terminator was missing or
malformed, the loop could run past the end of the fixed-size array.
Add an explicit bound check using ARRAY_SIZE() in both loops to prevent
a potential out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 55482edc25f0 ("qede: Add slowpath/fastpath support and enable hardware GRO") Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com> Link: https://patch.msgid.link/20251113112757.4166625-1-Pavel.Zhigulin@kaspersky.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In file uncore-frequency/uncore-frequency-common.h,
correct all kernel-doc warnings by adding missing leading " *" to some
lines, adding a missing kernel-doc entry, and fixing a name typo.
Warning: uncore-frequency-common.h:50 bad line:
Storage for kobject attribute elc_low_threshold_percent
Warning: uncore-frequency-common.h:52 bad line:
Storage for kobject attribute elc_high_threshold_percent
Warning: uncore-frequency-common.h:54 bad line:
Storage for kobject attribute elc_high_threshold_enable
Warning: uncore-frequency-common.h:92 struct member
'min_freq_khz_kobj_attr' not described in 'uncore_data'
Warning: uncore-frequency-common.h:92 struct member
'die_id_kobj_attr' not described in 'uncore_data'
Fixes: 24b6616355f7 ("platform/x86/intel-uncore-freq: Add efficiency latency control to sysfs interface") Fixes: 416de0246f35 ("platform/x86: intel-uncore-freq: Fix types in sysfs callbacks") Fixes: 247b43fcd872 ("platform/x86/intel-uncore-freq: Add attributes to show die_id") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://patch.msgid.link/20251111060938.1998542-1-rdunlap@infradead.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
isst_if_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c.
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning.
Airoha_eth driver forwards offloaded uplink traffic (packets received
on GDM1 and forwarded to GDM{3,4}) to GDM2 in order to apply hw QoS.
This is correct if the device does not support a dedicated GDM2 port.
In this case, in order to enable hw offloading for uplink traffic,
the packets should be sent to GDM{3,4} directly.
Introduce support to offload the traffic received on the ethernet NIC
and forwarded to the wireless one using HW Packet Processor Engine (PPE)
capabilities.
ret_set_ksft_status() calls ksft_status_merge() with the current return
status and the last one. It treats a non-zero return code from
ksft_status_merge() as an indication that the return status was
overwritten by the last one and therefore overwrites the return message
with the last one.
Currently, ksft_status_merge() returns a non-zero return code even if
the current return status and the last one are equal. This results in
return messages being overwritten which is counter-productive since we
are more interested in the first failure message and not the last one.
Fix by changing ksft_status_merge() to only return a non-zero return
code if the current return status was actually changed.
Add a test case which checks that the first error message is not
overwritten.
The function 'mpc_rcvd_sweep_req(mpcginfo)' is called conditionally
from function 'ctcmpc_unpack_skb'. It frees passed mpcginfo.
After that a call to function 'kfree' in function 'ctcmpc_unpack_skb'
frees it again.
Remove 'kfree' call in function 'mpc_rcvd_sweep_req(mpcginfo)'.
Blktests test cases nvme/014, 057 and 058 fail occasionally due to a
lockdep WARN. As reported in the Closes tag URL, the WARN indicates that
a deadlock can happen due to the dependency among disk->open_mutex,
kblockd workqueue completion and partition_scan_work completion.
To avoid the lockdep WARN and the potential deadlock, cut the dependency
by running the partition_scan_work not by kblockd workqueue but by
nvme_wq.
Reported-by: Yi Zhang <yi.zhang@redhat.com> Closes: https://lore.kernel.org/linux-block/CAHj4cs8mJ+R_GmQm9R8ebResKAWUE8kF5+_WVg0v8zndmqd6BQ@mail.gmail.com/ Link: https://lore.kernel.org/linux-block/oeyzci6ffshpukpfqgztsdeke5ost5hzsuz4rrsjfmvpqcevax@5nhnwbkzbrpa/ Fixes: 1f021341eef4 ("nvme-multipath: defer partition scanning") Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 7e091add9c43 "nvme-auth: update sc_c in host response" added
the sc_c variable to the dhchap queue context structure which is
appropriately set during negotiate and then used in the host response.
This breaks secure concat connections with a Linux target as the target
code wasn't updated at the same time. This patch fixes this by adding a
new sc_c variable to the host hash calculations.
Fixes: 7e091add9c43 ("nvme-auth: update sc_c in host response") Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Reviewed-by: Martin George <marting@netapp.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The file tools/arch/riscv/include/asm/csr.h borrows from
arch/riscv/include/asm/csr.h, and subsequent modifications
related to CSR should maintain consistency.
Signed-off-by: Chen Pei <cp0613@linux.alibaba.com> Link: https://patch.msgid.link/20251114071215.816-1-cp0613@linux.alibaba.com
[pjw@kernel.org: dropped Fixes: lines for patches that weren't broken; removed superfluous blank line] Signed-off-by: Paul Walmsley <pjw@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit dc82a33297fc ("veth: apply qdisc backpressure on full ptr_ring to
reduce TX drops") introduced a race condition that can lead to a permanently
stalled TXQ. This was observed in production on ARM64 systems (Ampere Altra
Max).
The race occurs in veth_xmit(). The producer observes a full ptr_ring and
stops the queue (netif_tx_stop_queue()). The subsequent conditional logic,
intended to re-wake the queue if the consumer had just emptied it (if
(__ptr_ring_empty(...)) netif_tx_wake_queue()), can fail. This leads to a
"lost wakeup" where the TXQ remains stopped (QUEUE_STATE_DRV_XOFF) and
traffic halts.
This failure is caused by an incorrect use of the __ptr_ring_empty() API
from the producer side. As noted in kernel comments, this check is not
guaranteed to be correct if a consumer is operating on another CPU. The
empty test is based on ptr_ring->consumer_head, making it reliable only for
the consumer. Using this check from the producer side is fundamentally racy.
This patch fixes the race by adopting the more robust logic from an earlier
version V4 of the patchset, which always flushed the peer:
(1) In veth_xmit(), the racy conditional wake-up logic and its memory barrier
are removed. Instead, after stopping the queue, we unconditionally call
__veth_xdp_flush(rq). This guarantees that the NAPI consumer is scheduled,
making it solely responsible for re-waking the TXQ.
This handles the race where veth_poll() consumes all packets and completes
NAPI *before* veth_xmit() on the producer side has called netif_tx_stop_queue.
The __veth_xdp_flush(rq) will observe rx_notify_masked is false and schedule
NAPI.
(2) On the consumer side, the logic for waking the peer TXQ is moved out of
veth_xdp_rcv() and placed at the end of the veth_poll() function. This
placement is part of fixing the race, as the netif_tx_queue_stopped() check
must occur after rx_notify_masked is potentially set to false during NAPI
completion.
This handles the race where veth_poll() consumes all packets, but haven't
finished (rx_notify_masked is still true). The producer veth_xmit() stops the
TXQ and __veth_xdp_flush(rq) will observe rx_notify_masked is true, meaning
not starting NAPI. Then veth_poll() change rx_notify_masked to false and
stops NAPI. Before exiting veth_poll() will observe TXQ is stopped and wake
it up.
Fixes: dc82a33297fc ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops") Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://patch.msgid.link/176295323282.307447.14790015927673763094.stgit@firesoul Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The validation of the set(nsh(...)) action is completely wrong.
It runs through the nsh_key_put_from_nlattr() function that is the
same function that validates NSH keys for the flow match and the
push_nsh() action. However, the set(nsh(...)) has a very different
memory layout. Nested attributes in there are doubled in size in
case of the masked set(). That makes proper validation impossible.
There is also confusion in the code between the 'masked' flag, that
says that the nested attributes are doubled in size containing both
the value and the mask, and the 'is_mask' that says that the value
we're parsing is the mask. This is causing kernel crash on trying to
write into mask part of the match with SW_FLOW_KEY_PUT() during
validation, while validate_nsh() doesn't allocate any memory for it:
The third issue with this process is that while trying to convert
the non-masked set into masked one, validate_set() copies and doubles
the size of the OVS_KEY_ATTR_NSH as if it didn't have any nested
attributes. It should be copying each nested attribute and doubling
them in size independently. And the process must be properly reversed
during the conversion back from masked to a non-masked variant during
the flow dump.
In the end, the only two outcomes of trying to use this action are
either validation failure or a kernel crash. And if somehow someone
manages to install a flow with such an action, it will most definitely
not do what it is supposed to, since all the keys and the masks are
mixed up.
Fixing all the issues is a complex task as it requires re-writing
most of the validation code.
Given that and the fact that this functionality never worked since
introduction, let's just remove it altogether. It's better to
re-introduce it later with a proper implementation instead of trying
to fix it in stable releases.
The call to devlink_info_version_fixed_put() in
mlxsw_linecard_devlink_info_get() did not check for errors,
although it is checked everywhere in the code.
Add missed 'err' check to the mlxsw_linecard_devlink_info_get()
Fixes: 3fc0c51905fb ("mlxsw: core_linecards: Expose device PSID over device info") Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20251113161922.813828-1-Pavel.Zhigulin@kaspersky.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LED setup routine registered both led_sync_good
and led_is_gm devices without checking the return
values of led_classdev_register(). If either registration
failed, the function continued silently, leaving the
driver in a partially-initialized state and leaking
a registered LED classdev.
Add proper error handling
Fixes: 7d9ee2e8ff15 ("net: dsa: hellcreek: Add PTP status LEDs") Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://patch.msgid.link/20251113135745.92375-1-Pavel.Zhigulin@kaspersky.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a call to put_pid() corresponding to get_task_pid().
host1x_memory_context_alloc() does not take ownership of the PID so we
need to free it here to avoid leaking.
The function mlxsw_sp_flower_stats() calls mlxsw_sp_acl_ruleset_get() to
obtain a ruleset reference. If the subsequent call to
mlxsw_sp_acl_rule_lookup() fails to find a rule, the function returns
an error without releasing the ruleset reference, causing a memory leak.
Fix this by using a goto to the existing error handling label, which
calls mlxsw_sp_acl_ruleset_put() to properly release the reference.
Fixes: 7c1b8eb175b69 ("mlxsw: spectrum: Add support for TC flower offload statistics") Signed-off-by: Zilin Guan <zilin@seu.edu.cn> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20251112052114.1591695-1-zilin@seu.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The WMI driver core only supports GUID strings containing only
uppercase characters, however the GUID string used by the
msi-wmi-platform driver contains a single lowercase character.
This prevents the WMI driver core from matching said driver to
its WMI device.
Fix this by turning the lowercase character into a uppercase
character. Also update the WMI driver development guide to warn
about this.
It turns out that the GUID used by the msi-wmi-platform driver
(ABBC0F60-8EA1-11D1-00A0-C90629100000) is not unique, but was instead
copied from the WIndows Driver Samples. This means that this driver
could load on devices from other manufacturers that also copied this
GUID, potentially causing hardware errors.
Prevent this by only loading on devices whitelisted via DMI. The DMI
matches where taken from the msi-ec driver.
Add a check to ensure locally generated packets (skb->sk != NULL) do
not use direct output in tunnel mode, as these packets require proper
L2 header setup that is handled by the normal XFRM processing path.
Fixes: 5eddd76ec2fd ("xfrm: fix tunnel mode TX datapath in packet offload mode") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The GSO segmentation functions for ESP tunnel mode
(xfrm4_tunnel_gso_segment and xfrm6_tunnel_gso_segment) were
determining the inner packet's L2 protocol type by checking the static
x->inner_mode.family field from the xfrm state.
This is unreliable. In tunnel mode, the state's actual inner family
could be defined by x->inner_mode.family or by
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed, causing GSO to create
segments with the wrong L2 header type.
This patch fixes the bug by deriving the inner mode directly from the
packet's inner protocol stored in XFRM_MODE_SKB_CB(skb)->protocol.
Instead of replicating the code, this patch modifies the
xfrm_ip2inner_mode helper function. It now correctly returns
&x->inner_mode if the selector family (x->sel.family) is already
specified, thereby handling both specific and AF_UNSPEC cases
appropriately.
With this change, ESP GSO can use xfrm_ip2inner_mode to get the
correct inner mode. It doesn't affect existing callers, as the updated
logic now mirrors the checks they were already performing externally.
Fixes: 26dbd66eab80 ("esp: choose the correct inner protocol for GSO on inter address family tunnels") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the output path, xfrm_dev_offload_ok and xfrm_get_inner_ipproto
need to determine the protocol family of the inner packet (skb) before
it gets encapsulated.
In xfrm_dev_offload_ok, the code checked x->inner_mode.family. This is
unreliable because, for states handling both IPv4 and IPv6, the
relevant inner family could be either x->inner_mode.family or
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed.
In xfrm_get_inner_ipproto, the code checked x->outer_mode.family. This
is also incorrect for tunnel mode, as the inner packet's family can be
different from the outer header's family.
At both of these call sites, the skb variable holds the original inner
packet. The most direct and reliable source of truth for its protocol
family is its destination entry. This patch fixes the issue by using
skb_dst(skb)->ops->family to ensure protocol-specific headers are only
accessed for the correct packet type.
The pinctrl-rtd driver uses 'devm_regmap_init_mmio', which requires
'REGMAP_MMIO' to be enabled.
Without this selection, the build fails with an undefined reference:
aarch64-none-linux-gnu-ld: drivers/pinctrl/realtek/pinctrl-rtd.o: in
function rtd_pinctrl_probe': pinctrl-rtd.c:(.text+0x5a0): undefined
reference to __devm_regmap_init_mmio_clk'
Fix this by selecting 'REGMAP_MMIO' in the Kconfig.
Fixes: e99ce78030db ("pinctrl: realtek: Add common pinctrl driver for Realtek DHC RTD SoCs") Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the user manual states that the PLL's rate should be between 180
MHz and 3 GHz in the register defninition section, it also says the
actual operating frequency is 22.5792*4 MHz in the PLL features table.
22.5792*4 MHz is one of the actual clock rates that we want and is
is available in the SDM table. Lower the minimum clock rate to 90 MHz
so that both rates in the SDM table can be used.
Fixes: 7cae1e2b5544 ("clk: sunxi-ng: Add support for the A523/T527 CCU PLLs") Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://patch.msgid.link/20251020171059.2786070-7-wens@kernel.org Signed-off-by: Chen-Yu Tsai <wens@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "bus-r-dma" clock in the A523's PRCM clock controller is also
referred to as "DMA_CLKEN_SW" or "DMA ADB400 gating". It is unclear how
this ties into the DMA controller MBUS clock gate; however if the clock
is not enabled, the DMA controller in the MCU block will fail to access
DRAM, even failing to retrieve the DMA descriptors.
Mark this clock as critical. This sort of mirrors what is done for the
main DMA controller's MBUS clock, which has a separate toggle that is
currently left out of the main clock controller driver.
Fixes: 8cea339cfb81 ("clk: sunxi-ng: add support for the A523/T527 PRCM CCU") Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://patch.msgid.link/20251020171059.2786070-6-wens@kernel.org Signed-off-by: Chen-Yu Tsai <wens@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
bus-r-cpucfg clock is important for peripheral which takes care of
powering CPU cores on and off. Since this operation is done by firmware
(TF-A), mark it as critical. That way Linux won't interfere with that
clock.
Fixes: 8cea339cfb81 ("clk: sunxi-ng: add support for the A523/T527 PRCM CCU") Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Andre Przywara <andre.przywara@arm.com> Link: https://patch.msgid.link/20251020152704.4804-1-jernej.skrabec@gmail.com Signed-off-by: Chen-Yu Tsai <wens@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xfrm_state_construct can fail without setting an error if the
requested pcpu_num value is too big. Set err and add an extack message
to avoid confusing userspace.
Fixes: 1ddf9916ac09 ("xfrm: Add support for per cpu xfrm state handling.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case xfrm_state_migrate fails after calling xfrm_dev_state_add, we
directly release the last reference and destroy the new state, without
calling xfrm_dev_state_delete (this only happens in
__xfrm_state_delete, which we're not calling on this path, since the
state was never added).
Call xfrm_dev_state_delete on error when an offload configuration was
provided.
In commit b441cf3f8c4b ("xfrm: delete x->tunnel as we delete x"), I
missed the case where state creation fails between full
initialization (->init_state has been called) and being inserted on
the lists.
In this situation, ->init_state has been called, so for IPcomp
tunnels, the fallback tunnel has been created and added onto the
lists, but the user state never gets added, because we fail before
that. The user state doesn't go through __xfrm_state_delete, so we
don't call xfrm_state_delete_tunnel for those states, and we end up
leaking the FB tunnel.
There are several codepaths affected by this: the add/update paths, in
both net/key and xfrm, and the migrate code (xfrm_migrate,
xfrm_state_migrate). A "proper" rollback of the init_state work would
probably be doable in the add/update code, but for migrate it gets
more complicated as multiple states may be involved.
At some point, the new (not-inserted) state will be destroyed, so call
xfrm_state_delete_tunnel during xfrm_state_gc_destroy. Most states
will have their fallback tunnel cleaned up during __xfrm_state_delete,
which solves the issue that b441cf3f8c4b (and other patches before it)
aimed at. All states (including FB tunnels) will be removed from the
lists once xfrm_state_fini has called flush_work(&xfrm_state_gc_work).
We're not updating x1, but we still need to put() it.
Fixes: a4a87fa4e96c ("xfrm: Add Direction to the SA in or out") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mt8189-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8189_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8189-pinctrl" dt-bindings, leading to possible dtbs check
issues. The mt8189_pinctrl_register_base_names entry order is also
different.
So, align all mt8189_pinctrl_register_base_names entry names and order
on dt-bindings.
Fixes: a3fe1324c3c5 ("pinctrl: mediatek: Add pinctrl driver for mt8189") Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mt8196-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8196_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8196-pinctrl" dt-bindings, leading to possible dtbs check
issues.
So, align all mt8196_pinctrl_register_base_names entries on dt-bindings
ones.
Fixes: f7a29377c253 ("pinctrl: mediatek: Add pinctrl driver on mt8196") Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Accesses within VMA, but beyond i_size rounded up to PAGE_SIZE are
supposed to generate SIGBUS.
This behavior might not be respected on truncation.
During truncation, the kernel splits a large folio in order to reclaim
memory. As a side effect, it unmaps the folio and destroys PMD mappings
of the folio. The folio will be refaulted as PTEs and SIGBUS semantics
are preserved.
However, if the split fails, PMD mappings are preserved and the user will
not receive SIGBUS on any accesses within the PMD.
Unmap the folio on split failure. It will lead to refault as PTEs and
preserve SIGBUS semantics.
Make an exception for shmem/tmpfs that for long time intentionally mapped
with PMDs across i_size.
Link: https://lkml.kernel.org/r/20251027115636.82382-3-kirill@shutemov.name Fixes: b9a8a4195c7d ("truncate,shmem: Handle truncates that split large folios") Signed-off-by: Kiryl Shutsemau <kas@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Christian Brauner <brauner@kernel.org> Cc: "Darrick J. Wong" <djwong@kernel.org> Cc: Dave Chinner <david@fromorbit.com> Cc: David Hildenbrand <david@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Rik van Riel <riel@surriel.com> Cc: Shakeel Butt <shakeel.butt@linux.dev> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
On DCN20 & DCN30, the 6th DPP's & HUBP's are powered on permanently and
cannot be power gated. Thus, when dpp_reset() is invoked for the DPP5,
while it's still powered on, the cached cursor_state
(dpp_base->pos.cur0_ctl.bits.cur0_enable)
and the actual state (CUR0_ENABLE) bit are unsycned. This can cause a
double cursor in full screen with non-native scaling.
[How]
Force disable cursor on DPP5 on plane powerdown for ASICs w/ 6 DPPs/HUBPs.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4673 Reviewed-by: Aric Cyr <aric.cyr@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 79b3c037f972dcb13e325a8eabfb8da835764e15) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Existing routine has two conversion sequence,
pbn_to_kbps and kbps_to_pbn with margin.
Non of those has without-margin calculation.
kbps_to_pbn with margin conversion includes
fec overhead which has already been included in
pbn_div calculation with 0.994 factor considered.
It is a double counted fec overhead factor that causes
potential bw loss.
[Why]
When a monitor is booting it's possible that it isn't ready to retrieve
link caps and this can lead to an EDID read failure:
```
[drm:retrieve_link_cap [amdgpu]] *ERROR* retrieve_link_cap: Read receiver caps dpcd data failed.
amdgpu 0000:c5:00.0: [drm] *ERROR* No EDID read.
```
[How]
Rather than msleep once and try a few times, msleep each time. Should
be no changes for existing working monitors, but should correct reading
caps on a monitor that is slow to boot.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4672 Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 669dca37b3348a447db04bbdcbb3def94d5997cc) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Empirical measurement of some monitors that fail to read EDID while
booting shows that the number of retries with a 30ms delay between
tries is as high as 16.
[How]
Increase number of retries to 20.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4672 Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ad1c59ad7cf74ec06e32fe2c330ac1e957222288) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
