The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize both pre-emphasis and voltage swing level to 0 before
start link training and do not end link training until video is
ready to reduce the period between end of link training and video
start to meet Link Layer CTS requirement. Some dongle main link
symbol may become unlocked again if host did not end link training
soon enough after completion of link training 2. Host have to re
train main link if loss of symbol locked detected before end link
training so that the coming video stream can be transmitted to sink
properly. This fixes Link Layer CTS cases 4.3.2.1, 4.3.2.2, 4.3.2.3
and 4.3.2.4.
Changes in v3:
-- merge retrain link if loss of symbol locked happen into this patch
-- replace dp_ctrl_loss_symbol_lock() with dp_ctrl_channel_eq_ok()
Reduce link rate and re start link training if link training 1
failed due to loss of clock recovery done to fix Link Layer
CTS case 4.3.1.7. Also only update voltage and pre-emphasis
swing level after link training started to fix Link Layer CTS
case 4.3.1.6.
Changes in V2:
-- replaced cr_status with link_status[DP_LINK_STATUS_SIZE]
-- replaced dp_ctrl_any_lane_cr_done() with dp_ctrl_colco_recovery_any_ok()
-- replaced dp_ctrl_any_ane_cr_lose() with !drm_dp_clock_recovery_ok()
Changes in V3:
-- return failed if lane_count <= 1
The issue is that the lock hierarchy should go from &hdev->lock -->
hci_cb_list_lock --> sk_lock-AF_BLUETOOTH-BTPROTO_SCO. For example,
one such call trace is:
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drm_file.master should be protected by either drm_device.master_mutex
or drm_file.master_lookup_lock when being dereferenced. However,
drm_master_get is called on unprotected file_priv->master pointers in
vmw_surface_define_ioctl and vmw_gb_surface_define_internal.
This is fixed by replacing drm_master_get with drm_file_get_master.
The program type cannot be deduced from 'tx' which causes an invalid
argument error when trying to load xdp_tx.o using the skeleton.
Rename the section name to "xdp" so that libbpf can deduce the type.
[How]
the programming sequeune was for old asic.
the correct programming sequeunce should be similar to the one
used in mpc. the fix is copied from the mpc programming sequeunce.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Anson Jacob <Anson.Jacob@amd.com> Signed-off-by: Roy Chan <roy.chan@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
If the plane has been removed, the writeback disablement logic
doesn't run
[How]
fix the logic order
Acked-by: Anson Jacob <Anson.Jacob@amd.com> Signed-off-by: Roy Chan <roy.chan@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because that in zynqmp_dp_probe it tries to access some DP
registers while the DP controller is still in the reset state. When
running "rmmod zynqmp_dpsub", zynqmp_dp_reset(dp, true) in
zynqmp_dp_phy_exit is called to force the DP controller into the reset
state. Then insmod will call zynqmp_dp_probe to program the DP registers,
but at this moment the DP controller hasn't been brought out of the reset
state yet since the function zynqmp_dp_reset(dp, false) is called later and
this will result the system hang.
Releasing the reset to DP controller before any read/write operation to it
will fix this issue. And for symmetry, move zynqmp_dp_reset() call from
zynqmp_dp_phy_exit() to zynqmp_dp_remove().
The Runtime PM subsystem will force the device "fd4a0000.zynqmp-display"
to enter suspend state while booting if the following conditions are met:
- the usage counter is zero (pm_runtime_get_sync hasn't been called yet)
- no 'active' children (no zynqmp-dp-snd-xx node under dpsub node)
- no other device in the same power domain (dpdma node has no
"power-domains = <&zynqmp_firmware PD_DP>" property)
So there is a scenario as below:
1) DP device enters suspend state <- call zynqmp_gpd_power_off
2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG
3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous
VPLL_FRAC_CFG configuration
4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG
configuration is corrupted
From above, we can see that pm_runtime_get_sync may clear register
VPLL_FRAC_CFG configuration and result the failure of clk enabling.
Putting pm_runtime_get_sync at the very beginning of the function
zynqmp_disp_crtc_atomic_enable can resolve this issue.
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
qfprom_disable_fuse_blowing() disables a bunch of resources,
and then does a few register writes in the 'conf' address
space.
It works perhaps because the resources are needed only for the
'raw' register space writes, and that the 'conf' space allows
read/writes regardless.
However that makes the code look confusing, so just move the
register writes before turning off the resources in the
function.
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'clock-output-names': ['xo_board'], 'phandle': [[115]]}
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'phandle': [[26]]}
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: sleep_clk: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[32768]]}
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit 6d7f677a2afa ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Cc: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Three interconnects are defined for IPA version 4.9, but there
should only be two. They should also use names that match what's
used for other platforms (and specified in the Device Tree binding).
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must not call gfs2_consist (which does a file system withdraw) from
the freeze glock's freeze_go_xmote_bh function because the withdraw
will try to use the freeze glock, thus causing a glock recursion error.
This patch changes freeze_go_xmote_bh to call function
gfs2_assert_withdraw_delayed instead of gfs2_consist to avoid recursion.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the stream fails to start, the first two buffers in the queue have
been moved to the active_vb2_buf array and are returned to vb2 by
imx7_csi_dma_unsetup_vb2_buf(). The function is called with the buffer
state set to VB2_BUF_STATE_ERROR unconditionally, which is correct when
stopping the stream, but not when the start operation fails. In that
case, the state should be set to VB2_BUF_STATE_QUEUED. Fix it.
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
We should not enable the switch interfaces at probe time since this is
trigged by the open callback. Remove the call dpsw_enable() which does
exactly this.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Code was checking if random_addr and hdev->rpa match without first
checking if the RPA has not been set (BDADDR_ANY), furthermore it was
clearing HCI_RPA_EXPIRED before the command completes and the RPA is
actually programmed which in case of failure would leave the expired
RPA still set.
Since advertising instance have a similar problem the clearing of
HCI_RPA_EXPIRED has been moved to hci_event.c after checking the random
address is in fact the hdev->rap and then proceed to set the expire
timeout.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The default SOF topology enables SSP capture and DMICs, even though
both of these hardware capabilities are not always available in
hardware (specific versions of HiFiberry and DMIC kit needed).
For the SSP capture, this leads to annoying "SP5-Codec: ASoC: no
backend capture" and "streamSSP5-Codec: ASoC: no users capture at
close - state 0" errors.
Update the quirks to match what the topology needs, which also allows
for the ability to remove SSP capture and DMIC support.
Move the "Platform Clock" routes for the "Internal Mic" and "Speaker"
routes to the intmic_*_map[] / *_spk_map[] arrays.
This ensures that these "Platform Clock" routes do not get added when the
BYT_RT5640_NO_INTERNAL_MIC_MAP / BYT_RT5640_NO_SPEAKERS quirks are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210802142501.991985-2-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use nfnetlink_unicast() which already translates EAGAIN to ENOBUFS,
since EAGAIN is reserved to report missing module dependencies to the
nfnetlink core.
e0241ae6ac59 ("netfilter: use nfnetlink_unicast() forgot to update
this spot.
Reported-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the following dtbs_check warning:
cs42l51@4a: port:endpoint@0:frame-master: True is not of type 'array'
cs42l51@4a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the following dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:frame-master: True is not of type 'array'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: kernel@dh-electronics.com Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
When the system shuts down or warm reboots, the display may be active,
with the hardware accessing system memory. Upon reboot, the DDR will not
be accessible, which may cause issues.
Implement the platform_driver .shutdown() operation and shut down the
display to fix this.
Last change to device managed APIs cleaned up error path to simple phy_exit()
call, which in some cases has been executed with NULL parameter. This per se
is not a problem, but rather logical misconception: no need to free resource
when it's for sure has not been allocated yet. Fix the driver accordingly.
When loading in parallel multiple programs which use the same to-be
pinned map, it is possible that two instances of the loader will call
bpf_object__create_maps() at the same time. If the map doesn't exist
when both instances call bpf_object__reuse_map(), then one of the
instances will fail with EEXIST when calling bpf_map__pin().
Fix the race by retrying reusing a map if bpf_map__pin() returns
EEXIST. The fix is similar to the one in iproute2: e4c4685fd6e4 ("bpf:
Fix race condition with map pinning").
Before retrying the pinning, we don't do any special cleaning of an
internal map state. The closer code inspection revealed that it's not
required:
- bpf_object__create_map(): map->inner_map is destroyed after a
successful call, map->fd is closed if pinning fails.
- bpf_object__populate_internal_map(): created map elements is
destroyed upon close(map->fd).
- init_map_slots(): slots are freed after their initialization.
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: linux-xtensa@linux-xtensa.org Acked-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Stop supporting different sizes for hashed and non-hashed filter or
route tables. Add BUILD_BUG_ON() calls to verify the sizes of the
fields in the filter/route table initialization immediate command
are the same.
Add a check to ipa_cmd_table_valid() to ensure the size of the
memory region being checked fits within the immediate command field
that must hold it.
Remove two Boolean parameters used only for error reporting. This
actually fixes a bug that would only show up if IPA_VALIDATE were
defined. Define ipa_cmd_table_valid() unconditionally (no longer
dependent on IPA_VALIDATE).
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
The userspace program could pass any values to the driver through
ioctl() interface. if the driver doesn't check the value of 'pixclock',
it may cause divide error because the value of 'lineclock' and
'frameclock' will be zero.
Fix this by checking whether 'pixclock' is zero in kyrofb_check_var().
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Christian Konig <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c48200 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return type of the function is bool and while NULL do evaluate to
false it's not very nice, fix this by explicitly returning false. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When hmm_pool_register() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Fix the following ingonred return val of asprintf() warn during
build:
cc -Wall -O2 fw_namespace.c -o ../tools/testing/selftests/firmware/fw_namespace
fw_namespace.c: In function ‘main’:
fw_namespace.c:132:2: warning: ignoring return value of ‘asprintf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
132 | asprintf(&fw_path, "/lib/firmware/%s", fw_name);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The virtual machine monitor (QEMU) exposes the pvpanic-pci
device to the guest. On guest side the module exists but
currently isn't loaded automatically. So the driver fails
to be probed and does not its job of handling guest panic
events.
Instead of requiring manual modprobe, let's include a device
database using the MODULE_DEVICE_TABLE macro and let the
module auto-load when the guest gets exposed with such a
pvpanic-pci device.
Some versions of the MC firmware wrongly report 0 for register base
address of the DPMCP associated with child DPRC objects thus rendering
them unusable. This is particularly troublesome in ACPI boot scenarios
where the legacy way of extracting this base address from the device
tree does not apply.
Given that DPMCPs share the same base address, workaround this by using
the base address extracted from the root DPRC container.
On Armadillo-800-EVA with CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/1
lock: lcdc0_device+0x10c/0x308, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 1 Comm: swapper Not tainted 5.11.0-rc5-armadillo-00036-gbbca04be7a80-dirty #287
Hardware name: Generic R8A7740 (Flattened Device Tree)
[<c010c3c8>] (unwind_backtrace) from [<c010a49c>] (show_stack+0x10/0x14)
[<c010a49c>] (show_stack) from [<c0159534>] (do_raw_spin_lock+0x20/0x94)
[<c0159534>] (do_raw_spin_lock) from [<c040858c>] (dev_pm_get_subsys_data+0x8c/0x11c)
[<c040858c>] (dev_pm_get_subsys_data) from [<c05fbcac>] (genpd_add_device+0x78/0x2b8)
[<c05fbcac>] (genpd_add_device) from [<c0412db4>] (of_genpd_add_device+0x34/0x4c)
[<c0412db4>] (of_genpd_add_device) from [<c0a1ea74>] (board_staging_register_device+0x11c/0x148)
[<c0a1ea74>] (board_staging_register_device) from [<c0a1eac4>] (board_staging_register_devices+0x24/0x28)
of_genpd_add_device() is called before platform_device_register(), as it
needs to attach the genpd before the device is probed. But the spinlock
is only initialized when the device is registered.
Fix this by open-coding the spinlock initialization, cfr.
device_pm_init_common() in the internal drivers/base code, and in the
SuperH early platform code.
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we should make use of the
usb_endpoint_* helpers instead and remove the unnecessary
max_packet()/hb_mult() macro.
projects / thirdparty / kernel / stable.git / log
