When a message was received the last_initiator is set to 0xff.
This will force the signal free time for the next transmit
to that for a new initiator. However, if a new transmit is
already in progress, then don't set last_initiator, since
that's the initiator of the current transmit. Overwriting
this would cause the signal free time of a following transmit
to be that of the new initiator instead of a next transmit.
Explicitly disable the CEC adapter in cec_devnode_unregister()
Usually this does not really do anything important, but for drivers
that use the CEC pin framework this is needed to properly stop the
hrtimer. Without this a crash would happen when such a driver is
unloaded with rmmod.
If plen is null when passed in, we only checked for null
in one of the two places where it could be used. Although
plen is always valid (not null) for current callers of the
SMB2_change_notify function, this change makes it more consistent.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Closes: https://lore.kernel.org/all/202305251831.3V1gbbFs-lkp@intel.com/ Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tpg->np_login_sem is a semaphore that is used to serialize the login
process when multiple login threads run concurrently against the same
target portal group.
The iscsi_target_locate_portal() function finds the tpg, calls
iscsit_access_np() against the np_login_sem semaphore and saves the tpg
pointer in conn->tpg;
If iscsi_target_locate_portal() fails, the caller will check for the
conn->tpg pointer and, if it's not NULL, then it will assume that
iscsi_target_locate_portal() called iscsit_access_np() on the semaphore.
Make sure that conn->tpg gets initialized only if iscsit_access_np() was
successful, otherwise iscsit_deaccess_np() may end up being called against
a semaphore we never took, allowing more than one thread to access the same
tpg.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Link: https://lore.kernel.org/r/20230508162219.1731964-4-mlombard@redhat.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the initiator suddenly stops sending data during a login while keeping
the TCP connection open, the login_work won't be scheduled and will never
release the login semaphore; concurrent login operations will therefore get
stuck and fail.
The bug is due to the inability of the login timeout code to properly
handle this particular case.
Fix the problem by replacing the old per-NP login timer with a new
per-connection timer.
The timer is started when an initiator connects to the target; if it
expires, it sends a SIGINT signal to the thread pointed at by the
conn->login_kworker pointer.
conn->login_kworker is set by calling the iscsit_set_login_timer_kworker()
helper, initially it will point to the np thread; When the login
operation's control is in the process of being passed from the NP-thread to
login_work, the conn->login_worker pointer is set to NULL. Finally,
login_kworker will be changed to point to the worker thread executing the
login_work job.
If conn->login_kworker is NULL when the timer expires, it means that the
login operation hasn't been completed yet but login_work isn't running, in
this case the timer will mark the login process as failed and will schedule
login_work so the latter will be forced to free the resources it holds.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Link: https://lore.kernel.org/r/20230508162219.1731964-2-mlombard@redhat.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Up until commit 6a45b0e2589f ("gpiolib: Introduce
gpiochip_irqchip_add_domain()") all irq_domains were allocated
by gpiolib itself and thus gpiolib also takes care of freeing it.
With gpiochip_irqchip_add_domain() a user of gpiolib can associate an
irq_domain with the gpio_chip. This irq_domain is not managed by
gpiolib and therefore must not be freed by gpiolib.
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pre-production prototypes (of which I only know one person
having one, Peter Geis), GPIO0 pin A5 was tied to the SDMMC
power enable pin on the CM4 connector. On all production models,
this is not the case; instead, this pin is used for the nEXTRST
signal, and the SDMMC power enable pin is always pulled high.
Since everyone currently using the SOQuartz device trees will
want this change, it is made to the tree without splitting the
trees into two separate ones of which users will then inevitably
choose the wrong one.
This fixes USB and PCIe on a wide variety of CM4IO-compatible
boards which use the nEXTRST signal.
This reverts commit 1f86123b9749 ("net: align SO_RCVMARK required
privileges with SO_MARK") because the reasoning in the commit message
is not really correct:
SO_RCVMARK is used for 'reading' incoming skb mark (via cmsg), as such
it is more equivalent to 'getsockopt(SO_MARK)' which has no priv check
and retrieves the socket mark, rather than 'setsockopt(SO_MARK) which
sets the socket mark and does require privs.
Additionally incoming skb->mark may already be visible if
sysctl_fwmark_reflect and/or sysctl_tcp_fwmark_accept are enabled.
Furthermore, it is easier to block the getsockopt via bpf
(either cgroup setsockopt hook, or via syscall filters)
then to unblock it if it requires CAP_NET_RAW/ADMIN.
On Android the socket mark is (among other things) used to store
the network identifier a socket is bound to. Setting it is privileged,
but retrieving it is not. We'd like unprivileged userspace to be able
to read the network id of incoming packets (where mark is set via
iptables [to be moved to bpf])...
An alternative would be to add another sysctl to control whether
setting SO_RCVMARK is privilged or not.
(or even a MASK of which bits in the mark can be exposed)
But this seems like over-engineering...
Note: This is a non-trivial revert, due to later merged commit e42c7beee71d
("bpf: net: Consider has_current_bpf_ctx() when testing capable() in sk_setsockopt()")
which changed both 'ns_capable' into 'sockopt_ns_capable' calls.
Fixes: 1f86123b9749 ("net: align SO_RCVMARK required privileges with SO_MARK") Cc: Larysa Zaremba <larysa.zaremba@intel.com> Cc: Simon Horman <simon.horman@corigine.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Eyal Birger <eyal.birger@gmail.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Patrick Rohr <prohr@google.com> Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230618103130.51628-1-maze@google.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this by moving the registration of source change notify handler only
when SPS(Static Slider) is advertised as supported.
Reported-by: Allen Zhong <allen@atr.me> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217571 Fixes: 4c71ae414474 ("platform/x86/amd/pmf: Add support SPS PMF feature") Tested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://lore.kernel.org/r/20230622060309.310001-1-Shyam-sundar.S-k@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When mirroring to a gretap in hardware the device expects to be
programmed with the egress port and all the encapsulating headers. This
requires the driver to resolve the path the packet will take in the
software data path and program the device accordingly.
If the path cannot be resolved (in this case because of an unresolved
neighbor), then mirror installation fails until the path is resolved.
This results in a race that causes the test to sometimes fail.
Fix this by setting the neighbor's state to permanent in a couple of
tests, so that it is always valid.
Fixes: 35c31d5c323f ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1d") Fixes: 239e754af854 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q") Signed-off-by: Danielle Ratson <danieller@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/268816ac729cb6028c7a34d4dda6f4ec7af55333.1687264607.git.petrm@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rather than assign the user pointer to msghdr->msg_control, assign it
to msghdr->msg_control_user to make sparse happy. They are in a union
so the end result is the same, but let's avoid new sparse warnings and
squash this one.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202306210654.mDMcyMuB-lkp@intel.com/ Fixes: cac9e4418f4c ("io_uring/net: save msghdr->msg_control for retries") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We currently allow to create perf link for program with
expected_attach_type == BPF_TRACE_KPROBE_MULTI.
This will cause crash when we call helpers like get_attach_cookie or
get_func_ip in such program, because it will call the kprobe_multi's
version (current->bpf_ctx context setup) of those helpers while it
expects perf_link's current->bpf_ctx context setup.
Making sure that we use BPF_TRACE_KPROBE_MULTI expected_attach_type
only for programs attaching through kprobe_multi link.
Fixes: ca74823c6e16 ("bpf: Add cookie support to programs attached with kprobe multi link") Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20230618131414.75649-1-jolsa@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When building a kernel with LLVM=1, LLVM_IAS=0 and CONFIG_KASAN=y, LLVM
leaves DWARF tags for the "asan.module_ctor" & co symbols. In turn,
pahole creates BTF_KIND_FUNC entries for these and this makes the BTF
metadata validation fail because they contain a dot.
In a dramatic turn of event, this BTF verification failure can cause
the netfilter_bpf initialization to fail, causing netfilter_core to
free the netfilter_helper hashmap and netfilter_ftp to trigger a
use-after-free. The risk of u-a-f in netfilter will be addressed
separately but the existence of "asan.module_ctor" debug info under some
build conditions sounds like a good enough reason to accept functions
that contain dots in BTF.
Although using only LLVM=1 is the recommended way to compile clang-based
kernels, users can certainly do LLVM=1, LLVM_IAS=0 as well and we still
try to support that combination according to Nick. To clarify:
- > v5.10 kernel, LLVM=1 (LLVM_IAS=0 is not the default) is recommended,
but user can still have LLVM=1, LLVM_IAS=0 to trigger the issue
- <= 5.10 kernel, LLVM=1 (LLVM_IAS=0 is the default) is recommended in
which case GNU as will be used
Fixes: 1dc92851849c ("bpf: kernel side support for BTF Var and DataSec") Signed-off-by: Florent Revest <revest@chromium.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andrii@kernel.org> Cc: Yonghong Song <yhs@meta.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/bpf/20230615145607.3469985-1-revest@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a regression in which the link would come up, but no
communication was possible.
The reverted commit was also removing a comment about
DP83867_PHYCR_FORCE_LINK_GOOD, this is not added back in this commits
since it seems that this is unrelated to the original code change.
Closes: https://lore.kernel.org/all/ZGuDJos8D7N0J6Z2@francesco-nb.int.toradex.com/ Fixes: da9ef50f545f ("net: phy: dp83867: perform soft reset and retain established link") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Praneeth Bajjuri <praneeth@ti.com> Link: https://lore.kernel.org/r/20230619154435.355485-1-francesco@dolcini.it Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Anonymous sets come with NFT_SET_CONSTANT from userspace. Although API
allows to create anonymous sets without NFT_SET_CONSTANT, it makes no
sense to allow to add and to delete elements for bound anonymous sets.
The .walk callback iterates over the current active set, but it might be
useful to iterate over the next generation set. Use the generation mask
to determine what set view (either current or next generation) is use
for the walk iteration.
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
set .destroy callback releases the references to other objects in maps.
This is very late and it results in spurious EBUSY errors. Drop refcount
from the preparation phase instead, update set backend not to drop
reference counter from set .destroy path.
Exceptions: NFT_TRANS_PREPARE_ERROR does not require to drop the
reference counter because the transaction abort path releases the map
references for each element since the set is unbound. The abort path
also deals with releasing reference counter for new elements added to
unbound sets.
Fixes: 591054469b3e ("netfilter: nf_tables: revisit chain/object refcounting from elements") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a new state to deal with rule expressions deactivation from the
newrule error path, otherwise the anonymous set remains in the list in
inactive state for the next generation. Mark the set/chain transaction
as unbound so the abort path releases this object, set it as inactive in
the next generation so it is not reachable anymore from this transaction
and reference counter is dropped.
Fixes: 1240eb93f061 ("netfilter: nf_tables: incorrect error path handling with NFT_MSG_NEWRULE") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add bound flag to rule and chain transactions as in 6a0a8d10a366
("netfilter: nf_tables: use-after-free in failing rule with bound set")
to skip them in case that the chain is already bound from the abort
path.
This patch fixes an imbalance in the chain use refcnt that triggers a
WARN_ON on the table and chain destroy path.
This patch also disallows nested chain bindings, which is not
supported from userspace.
The logic to deal with chain binding in nft_data_hold() and
nft_data_release() is not correct. The NFT_TRANS_PREPARE state needs a
special handling in case a chain is bound but next expressions in the
same rule fail to initialize as described by 1240eb93f061 ("netfilter:
nf_tables: incorrect error path handling with NFT_MSG_NEWRULE").
The chain is left bound if rule construction fails, so the objects
stored in this chain (and the chain itself) are released by the
transaction records from the abort path, follow up patch ("netfilter:
nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain")
completes this error handling.
When deleting an existing rule, chain bound flag is set off so the
rule expression .destroy path releases the objects.
We have seen a bug where the NIC incorrectly changes the length in the
IP header of a padded packet to include the padding bytes. The driver
already has a workaround for this so do the workaround for this NIC too.
This resolves the issue.
The NIC in question identifies itself as follows:
[ 8.828494] be2net 0000:02:00.0: FW version is 10.7.110.31
[ 8.834759] be2net 0000:02:00.0: Emulex OneConnect(be3): PF FLEX10 port 1
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
LLDP frames are link-local frames, therefore they must be trapped to the
CPU port. Currently, the MT753X switches treat LLDP frames as regular
multicast frames, therefore flooding them to user ports. To fix this, set
LLDP frames to be trapped to the CPU port(s).
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
BPDUs are link-local frames, therefore they must be trapped to the CPU
port. Currently, the MT7530 switch treats BPDUs as regular multicast
frames, therefore flooding them to user ports. To fix this, set BPDUs to be
trapped to the CPU port. Group this on mt7530_setup() and
mt7531_setup_common() into mt753x_trap_frames() and call that.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using encapsulation the original packet's headers are copied to the
inner headers. This preserves the space for an inner mac header, which
is not used by the inner payloads for the encapsulation types supported
by IPVS. If a packet is using GUE or GRE encapsulation and needs to be
segmented, flow can be passed to __skb_udp_tunnel_segment() which
calculates a negative tunnel header length. A negative tunnel header
length causes pskb_may_pull() to fail, dropping the packet.
This can be observed by attaching probes to ip_vs_in_hook(),
__dev_queue_xmit(), and __skb_udp_tunnel_segment():
These probes the headers and tunnel header length for packets which
traverse the IPVS encapsulation path. A TCP packet can be forced into
the segmentation path by being smaller than a calculated clamped MSS,
but larger than the advertised MSS.
When using veth-based encapsulation, the interfaces are set to be
mac-less, which does not preserve space for an inner mac header. This
prevents this issue from occurring.
In our real-world testing of sending a 32KB file we observed operation
time increasing from ~75ms for veth-based encapsulation to over 1.5s
using IPVS encapsulation due to retries from dropped packets.
This changeset modifies the packet on the encapsulation path in
ip_vs_tunnel_xmit() and ip_vs_tunnel_xmit_v6() to remove the inner mac
header offset. This fixes UDP segmentation for both encapsulation types,
and corrects the inner headers for any IPIP flows that may use it.
Fixes: 84c0d5e96f3a ("ipvs: allow tunneling with gue encapsulation") Signed-off-by: Terin Stock <terin@cloudflare.com> Acked-by: Julian Anastasov <ja@ssi.bg> Acked-by: Simon Horman <horms@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq_byname()
to -ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating error
codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 1b7ba57ecc86 ("mmc: sdhci-acpi: Handle return value of platform_get_irq") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230617203622.6812-9-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
In case the QCA7000 is not available via SPI (e.g. in reset),
the driver will cause a high load. The reason for this is
that the synchronization is never finished and schedule()
is never called. Since the synchronization is not timing
critical, it's safe to drop this from the scheduling condition.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running workloads heavy unbalanced towards TX (high TX, low RX
traffic), sfc driver can retain the CPU during too long times. Although
in many cases this is not enough to be visible, it can affect
performance and system responsiveness.
A way to reproduce it is to use a debug kernel and run some parallel
netperf TX tests. In some systems, this will lead to this message being
logged:
kernel:watchdog: BUG: soft lockup - CPU#12 stuck for 22s!
The reason is that sfc driver doesn't account any NAPI budget for the TX
completion events work. With high-TX/low-RX traffic, this makes that the
CPU is held for long time for NAPI poll.
Documentations says "drivers can process completions for any number of Tx
packets but should only process up to budget number of Rx packets".
However, many drivers do limit the amount of TX completions that they
process in a single NAPI poll.
In the same way, this patch adds a limit for the TX work in sfc. With
the patch applied, the watchdog warning never appears.
Tested with netperf in different combinations: single process / parallel
processes, TCP / UDP and different sizes of UDP messages. Repeated the
tests before and after the patch, without any noticeable difference in
network or CPU performance.
Test hardware:
Intel(R) Xeon(R) CPU E5-1620 v4 @ 3.50GHz (4 cores, 2 threads/core)
Solarflare Communications XtremeScale X2522-25G Network Adapter
Fixes: 5227ecccea2d ("sfc: remove tx and MCDI handling from NAPI budget consideration") Fixes: d19a53721863 ("sfc_ef100: TX path for EF100 NICs") Reported-by: Fei Liu <feliu@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20230615084929.10506-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When TUNNEL_L3_TO_L2 decap action was created, a pointer to a local
variable was passed as its HW action data, resulting in attempt to
free invalid address:
BUG: KASAN: invalid-free in mlx5dr_action_destroy+0x318/0x410 [mlx5_core]
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299a8d ("esp: Add a software GRO codepath") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d741150 ("selftests: Add tests for vrf and xfrms") Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Magali Lemes <magali.lemes@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TLS selftests use the ChaCha20-Poly1305 and SM4 algorithms, which are not
FIPS compliant. When fips=1, this set of tests fails. Add a check and only
run these tests if not in FIPS mode.
Fixes: 4f336e88a870 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests") Fixes: e506342a03c7 ("selftests/tls: add SM4 GCM/CCM to tls selftests") Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Magali Lemes <magali.lemes@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sysctl net/core/bpf_jit_enable does not work now due to commit 1022a5498f6f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc"). The
commit saved the jitted insns into 'rw_image' instead of 'image'
which caused bpf_jit_dump not dumping proper content.
With 'echo 2 > /proc/sys/net/core/bpf_jit_enable', run
'./test_progs -t fentry_test'. Without this patch, one of jitted
image for one particular prog is:
flen=17 proglen=92 pass=4 image=0000000014c64883 from=test_progs pid=1807 00000000: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000010: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000020: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000030: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000040: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 00000050: cc cc cc cc cc cc cc cc cc cc cc cc
With this patch, the jitte image for the same prog is:
Fixes: 1022a5498f6f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc") Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/bpf/20230609005439.3173569-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Before Linux v5.8 an AF_INET6 SOCK_DGRAM (udp/udplite) socket
with SOL_UDP, UDP_ENCAP, UDP_ENCAP_ESPINUDP{,_NON_IKE} enabled
would just unconditionally use xfrm4_udp_encap_rcv(), afterwards
such a socket would use the newly added xfrm6_udp_encap_rcv()
which only handles IPv6 packets.
Cc: Sabrina Dubroca <sd@queasysnail.net> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Benedict Wong <benedictwong@google.com> Cc: Yan Yan <evitayan@google.com> Fixes: 0146dca70b87 ("xfrm: add support for UDPv6 encapsulation of ESP") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The following scenario describes a bug in the verifier where it
incorrectly concludes about equivalent scalar IDs which could lead to
verifier bypass in privileged mode:
1. Prepare a 32-bit rogue number.
2. Put the rogue number into the upper half of a 64-bit register, and
roll a random (unknown to the verifier) bit in the lower half. The
rest of the bits should be zero (although variations are possible).
3. Assign an ID to the register by MOVing it to another arbitrary
register.
4. Perform a 32-bit spill of the register, then perform a 32-bit fill to
another register. Due to a bug in the verifier, the ID will be
preserved, although the new register will contain only the lower 32
bits, i.e. all zeros except one random bit.
At this point there are two registers with different values but the same
ID, which means the integrity of the verifier state has been corrupted.
5. Compare the new 32-bit register with 0. In the branch where it's
equal to 0, the verifier will believe that the original 64-bit
register is also 0, because it has the same ID, but its actual value
still contains the rogue number in the upper half.
Some optimizations of the verifier prevent the actual bypass, so
extra care is needed: the comparison must be between two registers,
and both branches must be reachable (this is why one random bit is
needed). Both branches are still suitable for the bypass.
6. Right shift the original register by 32 bits to pop the rogue number.
7. Use the rogue number as an offset with any pointer. The verifier will
believe that the offset is 0, while in reality it's the given number.
The fix is similar to the 32-bit BPF_MOV handling in check_alu_op for
SCALAR_VALUE. If the spill is narrowing the actual register value, don't
keep the ID, make sure it's reset to 0.
Fixes: 354e8f1970f8 ("bpf: Support <8-byte scalar spill and refill") Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Andrii Nakryiko <andrii@kernel.org> # Checked veristat delta Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20230607123951.558971-2-maxtram95@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Restore the host's PMUSERENR_EL0 value instead of clearing it,
before returning back to userspace, as the host's EL0 might have
a direct access to PMU registers (some bits of PMUSERENR_EL0 for
might not be zero for the host EL0).
This change adds methods in the XFRM-I input path that ensures that
policies are checked prior to processing of the subsequent decapsulated
packet, after which the relevant policies may no longer be resolvable
(due to changing src/dst/proto/etc).
Notably, raw ESP/AH packets did not perform policy checks inherently,
whereas all other encapsulated packets (UDP, TCP encapsulated) do policy
checks after calling xfrm_input handling in the respective encapsulation
layer.
Fixes: b0355dbbf13c ("Fix XFRM-I support for nested ESP tunnels")
Test: Verified with additional Android Kernel Unit tests
Test: Verified against Android CTS Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change allows inbound traffic through nested IPsec tunnels to
successfully match policies and templates, while retaining the secpath
stack trace as necessary for netfilter policies.
Specifically, this patch marks secpath entries that have already matched
against a relevant policy as having been verified, allowing it to be
treated as optional and skipped after a tunnel decapsulation (during
which the src/dst/proto/etc may have changed, and the correct policy
chain no long be resolvable).
This approach is taken as opposed to the iteration in b0355dbbf13c,
where the secpath was cleared, since that breaks subsequent validations
that rely on the existence of the secpath entries (netfilter policies, or
transport-in-tunnel mode, where policies remain resolvable).
Fixes: b0355dbbf13c ("Fix XFRM-I support for nested ESP tunnels")
Test: Tested against Android Kernel Unit Tests
Test: Tested against Android CTS Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KPTI keeps around two PGDs: one for userspace and another for the
kernel. Among other things, set_pgd() contains infrastructure to
ensure that updates to the kernel PGD are reflected in the user PGD
as well.
One side-effect of this is that set_pgd() expects to be passed whole
pages. Unfortunately, init_trampoline_kaslr() passes in a single entry:
'trampoline_pgd_entry'.
When KPTI is on, set_pgd() will update 'trampoline_pgd_entry' (an
8-Byte globally stored [.bss] variable) and will then proceed to
replicate that value into the non-existent neighboring user page
(located +4k away), leading to the corruption of other global [.bss]
stored variables.
Fix it by directly assigning 'trampoline_pgd_entry' and avoiding
set_pgd().
[ dhansen: tweak subject and changelog ]
Fixes: 0925dda5962e ("x86/mm/KASLR: Use only one PUD entry for real mode trampoline") Suggested-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/all/20230614163859.924309-1-lee@kernel.org/g Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We selectively grab the ctx->uring_lock for poll update/removal, but
we really should grab it from the start to fully synchronize with
linked timeouts. Normally this is indeed the case, but if requests
are forced async by the application, we don't fully cover removal
and timer disarm within the uring_lock.
Make this simpler by having consistent locking state for poll removal.
When __blkcg_rstat_flush() is called from cgroup_rstat_flush*() code
path, interrupt is always disabled.
When we start to flush blkcg per-cpu stats list in __blkg_release()
for avoiding to leak blkcg_gq's reference in commit 20cb1c2fb756
("blk-cgroup: Flush stats before releasing blkcg_gq"), local irq
isn't disabled yet, then lockdep warning may be triggered because
the dependent cgroup locks may be acquired from irq(soft irq) handler.
Fix the issue by disabling local irq always.
Fixes: 20cb1c2fb756 ("blk-cgroup: Flush stats before releasing blkcg_gq") Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Closes: https://lore.kernel.org/linux-block/pz2wzwnmn5tk3pwpskmjhli6g3qly7eoknilb26of376c7kwxy@qydzpvt6zpis/T/#u Cc: stable@vger.kernel.org Cc: Jay Shin <jaeshin@redhat.com> Cc: Tejun Heo <tj@kernel.org> Cc: Waiman Long <longman@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Waiman Long <longman@redhat.com> Link: https://lore.kernel.org/r/20230622084249.1208005-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register and range mappings for the PCIe controller in Rockchip's
RK356x SoCs are incorrect. Replace them with corrected values from the
vendor BSP sources, updated to match current DT schema.
These values are also used in u-boot.
Fixes: 66b51ea7d70f ("arm64: dts: rockchip: Add rk3568 PCIe2x1 controller") Cc: stable@vger.kernel.org Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com> Tested-by: Diederik de Haas <didi.debian@cknow.org> Link: https://lore.kernel.org/r/20230601132516.153934-1-frattaroli.nicolas@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ksmbd is doing write access using vfs helpers. There are the cases that
mnt_want_write() is not called in vfs helper. This patch add missing
mnt_want_write() to ksmbd vfs functions.
Cc: stable@vger.kernel.org Cc: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Al pointed out that ksmbd has racy issue from using ->d_parent and ->d_name
in ksmbd_vfs_unlink and smb2_vfs_rename(). and use new lock_rename_child()
to lock stable parent while underlying rename racy.
Introduce vfs_path_parent_lookup helper to avoid out of share access and
export vfs functions like the following ones to use
vfs_path_parent_lookup().
- rename __lookup_hash() to lookup_one_qstr_excl().
- export lookup_one_qstr_excl().
- export getname_kernel() and putname().
vfs_path_parent_lookup() is used for parent lookup of destination file
using absolute pathname given from FILE_RENAME_INFORMATION request.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 40b268d384a2 ("ksmbd: add mnt_want_write to ksmbd vfs functions") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pass the dentry of a source file and the dentry of a destination directory
to lock parent inodes for rename. As soon as this function returns,
->d_parent of the source file dentry is stable and inodes are properly
locked for calling vfs-rename. This helper is needed for ksmbd server.
rename request of SMB protocol has to rename an opened file, no matter
which directory it's in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stable-dep-of: 40b268d384a2 ("ksmbd: add mnt_want_write to ksmbd vfs functions") Signed-off-by: Sasha Levin <sashal@kernel.org>
The max_raw_write member of the regmap_spi_avmm_bus structure is defined
as:
.max_raw_write = SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
SPI_AVMM_VAL_SIZE == 4 and MAX_WRITE_CNT == 1 so this results in a
maximum write transfer size of 4 bytes which provides only enough space to
transfer the address of the target register. It provides no space for the
value to be transferred. This bug became an issue (divide-by-zero in
_regmap_raw_write()) after the following was accepted into mainline:
commit 3981514180c9 ("regmap: Account for register length when chunking")
Change max_raw_write to include space (4 additional bytes) for both the
register address and value:
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
When subprograms are in use, the main program is not jit'd after the
subprograms because jit_subprogs sets a value for prog->bpf_func upon
success. Subsequent calls to the JIT are bypassed when this value is
non-NULL. This leads to a situation where the main program and its
func[0] counterpart are both in the bpf kallsyms tree, but only func[0]
has an extable. Extables are only created during JIT. Now there are
two nearly identical program ksym entries in the tree, but only one has
an extable. Depending upon how the entries are placed, there's a chance
that a fault will call search_extable on the aux with the NULL entry.
Since jit_subprogs already copies state from func[0] to the main
program, include the extable pointer in this state duplication.
Additionally, ensure that the copy of the main program in func[0] is not
added to the bpf_prog_kallsyms table. Instead, let the main program get
added later in bpf_prog_load(). This ensures there is only a single
copy of the main program in the kallsyms table, and that its tag matches
the tag observed by tooling like bpftool.
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-2-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
The way that the timeout is currently calculated could lead to a u64
timeout value in mmci_start_command(). This value is then cast in a u32
register that leads to mmc erase failed issue with some SD cards.
The call to mmc_request_done() can schedule, so it must not be called
from irq context. Wake the irq thread if it needs to be called, and let
its existing logic do its work.
While SDHCI claims to support 64-bit DMA on MSM8916 it does not seem to
be properly functional. It is not immediately obvious because SDHCI is
usually used with IOMMU bypassed on this SoC, and all physical memory
has 32-bit addresses. But when trying to enable the IOMMU it quickly
fails with an error such as the following:
Looking closely it's obvious that only the 32-bit part of the address
(0xfffff200) arrives at the SMMU, the higher 16-bit (0xffff...) get
lost somewhere. This might not be a limitation of the SDHCI itself but
perhaps the bus/interconnect it is connected to, or even the connection
to the SMMU.
Work around this by setting SDHCI_QUIRK2_BROKEN_64_BIT_DMA to avoid
using 64-bit addresses.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230518-msm8916-64bit-v1-1-5694b0f35211@gerhold.net Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc host drivers should have enabled the asynchronous probe option, but
it seems like we didn't set it for litex_mmc when introducing litex mmc
support, so let's set it now.
Tested with linux-on-litex-vexriscv on sipeed tang nano 20K fpga.
syzbot is again reporting circular locking dependency between
cpu_hotplug_lock and freezer_mutex. Do like what we did with
commit 57dcd64c7e036299 ("cgroup,freezer: hold cpu_hotplug_lock
before freezer_mutex").
Inside css_task_iter_start/next/end, css_set_lock is hold and then
released, so when iterating task(left side), the css_set may be moved to
another list(right side), then it->cset_head points to the old list head
and it->cset_pos->next points to the head node of new list, which can't
be used as struct css_set.
To fix this issue, switch from all css_sets to only scgrp's css_sets to
patch in-flight iterators to preserve correct iteration, and then
update it->cset_head as well.
The MPTCP protocol access the listener subflow in a lockless
manner in a couple of places (poll, diag). That works only if
the msk itself leaves the listener status only after that the
subflow itself has been closed/disconnected. Otherwise we risk
deadlock in diag, as reported by Christoph.
Address the issue ensuring that the first subflow (the listener
one) is always disconnected before updating the msk socket status.
Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/407 Fixes: b29fcfb54cd7 ("mptcp: full disconnect implementation") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An orphaned msk releases the used resources via the worker,
when the latter first see the msk in CLOSED status.
If the msk status transitions to TCP_CLOSE in the release callback
invoked by the worker's final release_sock(), such instance of the
workqueue will not take any action.
Additionally the MPTCP code prevents scheduling the worker once the
socket reaches the CLOSE status: such msk resources will be leaked.
The only code path that can trigger the above scenario is the
__mptcp_check_send_data_fin() in fallback mode.
Address the issue removing the special handling of fallback socket
in __mptcp_check_send_data_fin(), consolidating the state machine
for fallback and non fallback socket.
Since non-fallback sockets do not send and do not receive data_fin,
the mptcp code can update the msk internal status to match the next
step in the SM every time data fin (ack) should be generated or
received.
As a consequence we can remove a bunch of checks for fallback from
the fastpath.
Fixes: 6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At passive MPJ time, if the msk socket lock is held by the user,
the new subflow is appended to the msk->join_list under the msk
data lock.
In mptcp_release_cb()/__mptcp_flush_join_list(), the subflows in
that list are moved from the join_list into the conn_list under the
msk socket lock.
Append and removal could race, possibly corrupting such list.
Address the issue splicing the join list into a temporary one while
still under the msk data lock.
Found by code inspection, the race itself should be almost impossible
to trigger in practice.
Fixes: 3e5014909b56 ("mptcp: cleanup MPJ subflow list handling") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mptcp_recvmsg is allowed to release the msk socket lock when
blocking, and before re-acquiring it another thread could have
switched the sock to TCP_LISTEN status - with a prior
connect(AF_UNSPEC) - also clearing icsk_ack.rcv_mss.
Address the issue preventing the disconnect if some other process is
concurrently performing a blocking syscall on the same socket, alike
commit 4faeee0cf8a5 ("tcp: deny tcp_disconnect() when threads are waiting").
Fixes: a6b118febbab ("mptcp: add receive buffer auto-tuning") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/404 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the mptcp code has assumes that disconnect() can fail only
at mptcp_sendmsg_fastopen() time - to avoid a deadlock scenario - and
don't even bother returning an error code.
Soon mptcp_disconnect() will handle more error conditions: let's track
them explicitly.
As a bonus, explicitly annotate TCP-level disconnect as not failing:
the mptcp code never blocks for event on the subflows.
Fixes: 7d803344fdc3 ("mptcp: fix deadlock in fastopen error path") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot sanely handle partial retries for recvmsg if we have cmsg
attached. If we don't, then we'd just be overwriting the initial cmsg
header on retries. Alternatively we could increment and handle this
appropriately, but it doesn't seem worth the complication.
Move the MSG_WAITALL check into the non-multishot case while at it,
since MSG_WAITALL is explicitly disabled for multishot anyway.
In the case of fast device addition/removal, it's possible that
hv_eject_device_work() can start to run before create_root_hv_pci_bus()
starts to run; as a result, the pci_get_domain_bus_and_slot() in
hv_eject_device_work() can return a 'pdev' of NULL, and
hv_eject_device_work() can remove the 'hpdev', and immediately send a
message PCI_EJECTION_COMPLETE to the host, and the host immediately
unassigns the PCI device from the guest; meanwhile,
create_root_hv_pci_bus() and the PCI device driver can be probing the
dead PCI device and reporting timeout errors.
Fix the issue by adding a per-bus mutex 'state_lock' and grabbing the
mutex before powering on the PCI bus in hv_pci_enter_d0(): when
hv_eject_device_work() starts to run, it's able to find the 'pdev' and call
pci_stop_and_remove_bus_device(pdev): if the PCI device driver has
loaded, the PCI device driver's probe() function is already called in
create_root_hv_pci_bus() -> pci_bus_add_devices(), and now
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able
to call the PCI device driver's remove() function and remove the device
reliably; if the PCI device driver hasn't loaded yet, the function call
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able to
remove the PCI device reliably and the PCI device driver's probe()
function won't be called; if the PCI device driver's probe() is already
running (e.g., systemd-udev is loading the PCI device driver), it must
be holding the per-device lock, and after the probe() finishes and releases
the lock, hv_eject_device_work() -> pci_stop_and_remove_bus_device() is
able to proceed to remove the device reliably.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-6-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the host tries to remove a PCI device, the host first sends a
PCI_EJECT message to the guest, and the guest is supposed to gracefully
remove the PCI device and send a PCI_EJECTION_COMPLETE message to the host;
the host then sends a VMBus message CHANNELMSG_RESCIND_CHANNELOFFER to
the guest (when the guest receives this message, the device is already
unassigned from the guest) and the guest can do some final cleanup work;
if the guest fails to respond to the PCI_EJECT message within one minute,
the host sends the VMBus message CHANNELMSG_RESCIND_CHANNELOFFER and
removes the PCI device forcibly.
In the case of fast device addition/removal, it's possible that the PCI
device driver is still configuring MSI-X interrupts when the guest receives
the PCI_EJECT message; the channel callback calls hv_pci_eject_device(),
which sets hpdev->state to hv_pcichild_ejecting, and schedules a work
hv_eject_device_work(); if the PCI device driver is calling
pci_alloc_irq_vectors() -> ... -> hv_compose_msi_msg(), we can break the
while loop in hv_compose_msi_msg() due to the updated hpdev->state, and
leave data->chip_data with its default value of NULL; later, when the PCI
device driver calls request_irq() -> ... -> hv_irq_unmask(), the guest
crashes in hv_arch_irq_unmask() due to data->chip_data being NULL.
Fix the issue by not testing hpdev->state in the while loop: when the
guest receives PCI_EJECT, the device is still assigned to the guest, and
the guest has one minute to finish the device removal gracefully. We don't
really need to (and we should not) test hpdev->state in the loop.
Fixes: de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-3-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The statement "the hv_pci_bus_exit() call releases structures of all its
child devices" in commit d6af2ed29c7c is not true: in the path
hv_pci_probe() -> hv_pci_enter_d0() -> hv_pci_bus_exit(hdev, true): the
parameter "keep_devs" is true, so hv_pci_bus_exit() does *not* release the
child "struct hv_pci_dev *hpdev" that is created earlier in
pci_devices_present_work() -> new_pcichild_device().
The commit d6af2ed29c7c was originally made in July 2020 for RHEL 7.7,
where the old version of hv_pci_bus_exit() was used; when the commit was
rebased and merged into the upstream, people didn't notice that it's
not really necessary. The commit itself doesn't cause any issue, but it
makes hv_pci_probe() more complicated. Revert it to facilitate some
upcoming changes to hv_pci_probe().
Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Wei Hu <weh@microsoft.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-5-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since day 1 of the driver, there has been a race between
hv_pci_query_relations() and survey_child_resources(): during fast
device hotplug, hv_pci_query_relations() may error out due to
device-remove and the stack variable 'comp' is no longer valid;
however, pci_devices_present_work() -> survey_child_resources() ->
complete() may be running on another CPU and accessing the no-longer-valid
'comp'. Fix the race by flushing the workqueue before we exit from
hv_pci_query_relations().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230615044451.5580-2-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmbus_wait_for_unload() may be called in the panic path after other
CPUs are stopped. vmbus_wait_for_unload() currently loops through
online CPUs looking for the UNLOAD response message. But the values of
CONFIG_KEXEC_CORE and crash_kexec_post_notifiers affect the path used
to stop the other CPUs, and in one of the paths the stopped CPUs
are removed from cpu_online_mask. This removal happens in both
x86/x64 and arm64 architectures. In such a case, vmbus_wait_for_unload()
only checks the panic'ing CPU, and misses the UNLOAD response message
except when the panic'ing CPU is CPU 0. vmbus_wait_for_unload()
eventually times out, but only after waiting 100 seconds.
Fix this by looping through *present* CPUs in vmbus_wait_for_unload().
The cpu_present_mask is not modified by stopping the other CPUs in the
panic path, nor should it be.
Also, in a CoCo VM the synic_message_page is not allocated in
hv_synic_alloc(), but is set and cleared in hv_synic_enable_regs()
and hv_synic_disable_regs() such that it is set only when the CPU is
online. If not all present CPUs are online when vmbus_wait_for_unload()
is called, the synic_message_page might be NULL. Add a check for this.
Fixes: cd95aad55793 ("Drivers: hv: vmbus: handle various crash scenarios") Cc: stable@vger.kernel.org Reported-by: John Starks <jostarks@microsoft.com> Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1684422832-38476-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 572086325ce9 ("Drivers: hv: vmbus: Cleanup synic memory free path")
says "Any memory allocations that succeeded will be freed when the caller
cleans up by calling hv_synic_free()", but if the get_zeroed_page() in
hv_synic_alloc() fails, currently hv_synic_free() is not really called
in vmbus_bus_init(), consequently there will be a memory leak, e.g.
hv_context.hv_numa_map is not freed in the error path. Fix this by
updating the goto labels.
Cc: stable@kernel.org Signed-off-by: Dexuan Cui <decui@microsoft.com> Fixes: 4df4cb9e99f8 ("x86/hyperv: Initialize clockevents earlier in CPU onlining") Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20230504224155.10484-1-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return of do_mprotect_pkey() can still be incorrectly returned as
success if there is a gap that spans to or beyond the end address passed
in. Update the check to ensure that the end address has indeed been seen.
In __vmalloc_area_node() we always warn_alloc() when an allocation
performed by vm_area_alloc_pages() fails unless it was due to a pending
fatal signal.
However, huge page allocations instigated either by vmalloc_huge() or
__vmalloc_node_range() (or a caller that invokes this like kvmalloc() or
kvmalloc_node()) always falls back to order-0 allocations if the huge page
allocation fails.
This renders the warning useless and noisy, especially as all callers
appear to be aware that this may fallback. This has already resulted in
at least one bug report from a user who was confused by this (see link).
Therefore, simply update the code to only output this warning for order-0
pages when no fatal signal is pending.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1211410 Link: https://lkml.kernel.org/r/20230605201107.83298-1-lstoakes@gmail.com Fixes: 80b1d8fdfad1 ("mm: vmalloc: correct use of __GFP_NOWARN mask in __vmalloc_area_node()") Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Baoquan He <bhe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c71835228 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35c9
("KVM: ARM: Memory virtualization setup").
Cc: stable@vger.kernel.org # v3.9+ Fixes: d5d8184d35c9 ("KVM: ARM: Memory virtualization setup") Reported-by: Shuai Hu <hshuai@redhat.com> Reported-by: Zhenyu Zhang <zhenyzha@redhat.com> Signed-off-by: Gavin Shan <gshan@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Reviewed-by: Peter Xu <peterx@redhat.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Message-Id: <20230615054259.14911-1-gshan@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
