Daniel Golle [Sat, 25 Feb 2023 17:49:10 +0000 (17:49 +0000)]
tools/squashfs4: fix PKG_MIRROR_HASH
The hash currently matches neither the SHA256 of the Github download
nor the hash of the archive generated by the OpenWrt build system.
(and yes, they differ...)
Set hash of Github-generated tarball.
Fixes: 30f2d516ba ("tools/squashfs4: add new tool for squashfs4 images") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 25 Feb 2023 02:35:16 +0000 (02:35 +0000)]
mvebu: puzzle: fix fan thermal cooling driver
Several fixes for the Puzzle WT61P803 hwmon driver were needed to make
it behave well as thermal cooling device:
- wire-up cooling device with OF node in device tree
- properly parse cooling-levels (u32 with range check vs. u8)
- actually use cooling-levels
- keep current state and only write to uC if state has changed
(avoids flooding the uC with commands which will result in uC crashing)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Sat, 25 Feb 2023 18:56:12 +0000 (19:56 +0100)]
netifd: update to the latest version
ed65a00 netifd: bridge: Fix format string position 19372d8 netifd: Fix multiple -Wsign-compare warnings 8ebf033 netifd: Do not return values in void function c77417a netifd: Explicitly zero initialize variables 463a120 netifd: Activate -Wextra compile warnings
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
Michael Pratt [Tue, 21 Feb 2023 19:58:20 +0000 (14:58 -0500)]
toolchain: remove references to $(LIBC)/utils subtarget
The utils subtarget was used for uClibc and eglibc
which are both obsolete and replaced in Openwrt by mainline
musl and glibc, which do not have a utils Makefile target.
Ref: 5d19a38d8 ("toolchain: sync eglibc headers/build split with uclibc changes") Fixes: 63fb17520 ("toolchain: remove uClibc-ng") Suggested-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Sat, 10 Sep 2022 01:43:18 +0000 (21:43 -0400)]
toolchain: fix stampfile dependency
Use the gcc/final/install target stampfile as the prerequisite
for the toolchain/compile target stampfile.
The previous filename was also incorrect,
the stampfile name format was changed (see reference)
but was never updated here.
The issue was never noticed
because the usage of timestamp.pl was broken
(fixed in previous commit)
causing the extra prereq files passed to 'call stampfile'
to never get checked at all.
Fixes: 5149ed151 ("gcc: split up the build process into three distinct stages") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Nick Hainke [Wed, 22 Feb 2023 14:50:43 +0000 (15:50 +0100)]
ethtool: update to 6.2
Release notes:
- Feature: link down event statistics (no option)
- Feature: JSON output for coalesce (-c)
- Feature: new link modes (no option)
- Feature: JSON output for ring (-g)
- Feature: netlink handler for RSS get (-x)
- Fix: fix boolean value output in JSON output
- Fix: fix build errors and warnings
Robert Marko [Sun, 19 Feb 2023 11:58:56 +0000 (12:58 +0100)]
mvebu: mochabin: enlarge PCI memory window
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch.
Swconfig driver for QCA8327 switch is removed because this router is
only one device which use Qualcom swconfig switch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
Andre Heider [Tue, 7 Feb 2023 20:33:33 +0000 (21:33 +0100)]
toolchain: remove installing twice in the "initial" subdir
This was apparently introduced to recreate the toolchain (wipe
staging_dir/toolchain*, but keep build_dir/toolchain*, followed by a
`make toolchain/compile`).
But it leaves leftovers and causes re-links to happen at src_install phase,
because of the changed paths, possibly adding yet another source of issues.
With the prior commits removing various hacks related to the "initial"
folder we can remove installing it twice altogether.
The recreated toolchain is exactly the same as before.
Andre Heider [Mon, 30 Jan 2023 09:55:53 +0000 (10:55 +0100)]
toolchain/glibc: fixup the libm.so linker script too
Add it to the existing list to fix it up.
Found by mold:
toolchain-x86_64_gcc-12.2.0_glibc/lib/libm.so:4: GROUP ( /lib/libm.so.6 AS_NEEDED ( /lib/libmvec.so.1 ) )
^ library not found: /lib/libm.so.6
hostapd: always use sae_password for mesh/SAE auth
This patch fixes a corner case when using passwords that are exactly 64
characters in length with mesh mode or passwords longer than 63 characters
with SAE because 'psk' is used instead of 'sae_password'.
SAE is obligatory for 802.11s (mesh point).
The 'psk' option for hostapd is suited for WPA2 and enforces length
restrictions on passwords. Values of 64 characters are treated as PMKs.
With SAE, PMKs are always generated during the handshake and there are no
length restrictions.
The 'sae_password' option is more suited for SAE and should be used
instead.
Before this patch, the 'sae_password' option is only used with mesh mode
passwords that are not 64 characters long.
As a consequence:
- mesh passwords can't be 64 characters in length
- SAE only works with passwords with lengths >8 and <=63 (due to psk
limitation).
Fix this by always using 'sae_password' with SAE/mesh and applying the PMK
differentiation only when PSK is used.
Fixes: #11324 Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ improve commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Shiji Yang [Sun, 19 Feb 2023 01:06:32 +0000 (09:06 +0800)]
ramips: add alternative device name for Wiflyer WF3526-P
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.
Shiji Yang [Sun, 19 Feb 2023 01:06:32 +0000 (09:06 +0800)]
ramips: correct the PCIe port number for Zbtlink ZBT-WE1326
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.
According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Yuan Tao [Mon, 14 Sep 2020 09:19:49 +0000 (17:19 +0800)]
base-files: sysfixtime: Fix time on the fake RTC
On some devices the chip has RTC but no battery save time.
This leads back to getting the wrong time
and skipping the check of the last file modification date.
This commit ensures that the file time is checked even
if the RTC exists.
which would ordinarily return an approbiate
system time used for e.g. certificate generation.
The name of squashfs is confusing since in reality it's a really old
version using an old lzma library. This tools is used for old ath79
netgear target and to produde a fake squasfs3 image needed for some
specific bootloader from some OEM (AVM for example)
Rename squashfs tool to squasfs3-lzma to better describe it.
Rename the installed bin from mksquashfs-lzma to mksquashfs3-lzma.
Use tar transform to migrate the root directory in tar to the new
naming.
Drop redundant PKG_CAT variable not needed anymore.
Also update any user of this tool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Brian Norris [Sun, 5 Feb 2023 00:35:35 +0000 (16:35 -0800)]
ipq40xx: chromium: Enable kmod-ramoops by default
Chromium devices (like Google WiFi) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Sun, 5 Feb 2023 00:35:34 +0000 (16:35 -0800)]
ipq806x: chromium: Enable kmod-ramoops by default
Chromium devices (like OnHub) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Sun, 5 Feb 2023 00:35:33 +0000 (16:35 -0800)]
kernel: kmod-ramoops: Include pstore console support
Pstore ramoops support is useful even when there isn't an explicit
panic/crash. We can log all kernel messages via a "console", and then
retrieve them in the event of some non-kernel-panic reset (e.g.,
watchdog).
Since the buffer memory is already reserved, there isn't much overhead
to doing this.
The new console files will show up as:
/sys/fs/pstore/console-ramoops-N
Cc: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Michael Pratt [Mon, 19 Apr 2021 19:45:32 +0000 (15:45 -0400)]
ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
Michael Pratt [Thu, 17 Mar 2022 03:02:42 +0000 (23:02 -0400)]
ramips: mt7620: split gsw hw_init to mac_init, ephy_init
in order for the option ephy-disable to work
without also needing ephy-base option,
we have to skip all the lines that write to mdio addresses that
assume those addresses do not have an external switch.
Otherwise, ephy ports will be disabled in hardware,
but register writes still happen as if they are enabled.
Split the functions so that other things are done first,
and ephy port setup can be skipped with a simple "return".
Tested on Engenius EPG600 (MT7620A ver:2 eco:3)
with QCA8337 external switch
Ref: cc6fd6fbb505 ("ramips: mt7620: add ephy-disable option to switch driver") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Yuu Toriyama [Tue, 14 Feb 2023 05:44:11 +0000 (14:44 +0900)]
wireless-regdb: update to 2023.02.13
Changes: 7f7a9f7 wireless-regdb: update regulatory database based on preceding changes 660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH) f29772a wireless-regdb: Update regulatory rules for Brazil (BR)
Karol Przybylski [Tue, 14 Feb 2023 22:32:56 +0000 (23:32 +0100)]
ipq807x: Add bluetooth driver to zyxel nbg7815
Zyxel NBG7815 supports bluetooth with blsp1_uart3.
Configuration are already added to dts file, device needs only module to working bluetooth properly.
Tested at below posts:
https://forum.openwrt.org/t/openwrt-support-for-armor-g5-nbg7815/98598/259?u=itork
Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Karol Przybylski <karol.przybylski@esm-technology.pl>
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation] Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Some devices like ZBT WE1326 and ZBT WF3526-P and some Netgear models need
to delay phy port initialization after calling the mt7621_pcie_init_port()
driver function to get into reliable boots for both warm and hard resets.
ipq806x: fix Linksys EAX500 family devices dead Ethernet switch
With 5.15 kernel version Linksys EAX500 family devices suffered from a
big regression where the Ethernet switch became silent and started to
malfunction.
It was discovered later that the cause was not really the kernel upgrade
itself but a hackish implementation of the hw implementation of these
special routers.
In the original Linksys source code, GPIO 63 was handled in a special way
and was reset on reboot.
Normally GPIO 63 is used for pcie2 reset but in every device we support,
pcie2 is actually never used as nothing is attached to it.
Linksys rerouted GPIO 63 to the switch reset pin and deviates from
common hw implementation.
Till now it was used an hack to handle this case... It was set pcie3 as
working (while actually nothing was connected), set it to output low
(for assert-deassert from the pcie init code) and be done with it.
The result was that the GPIO was reset for enough time in early boot and
everything worked correctly.
This hack implementation was born to fail from the very start and in
kernel 5.15 finally problem arised.
In 5.15 pcie code changed and now the GPIO reset pin is not asserted as
probe won't fail if nothing is connected to the line (the old behaviour)
This result in the switch hold the reset pin and the Ethernet switch
dead.
On top of that with 5.15 code got optimized and simply attaching the
GPIO reset to the mdio wasn't enough as the switch require at least 10ms
to be correctly reset.
So implement finally a correct solution where:
- pcie2 is correctly disabled (nothing attached, unused)
- drop the wrong output-low for pcie2 reset pin
- define GPIO 63 as switch reset
- Add the reset-gpios to the mdio0 node
- Set the reset-post-delay-us to 12ms to correctly give time the switch
to reset
Fixes: #10983 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
I tested kernel 5.15 on my device for several times without any problems.
In my tests, 5.15 kernel has performance improvements such MGLRU.
Finally, initial kernel 6.1 support is imminent. All ramips subtargets have
5.15 as testing kernel. So, it's time to change.
Tested on my Archer C6 v3.2 (mt7621)
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
[reformat commit subject and message] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Wed, 7 Dec 2022 17:04:12 +0000 (19:04 +0200)]
build: add option to use preinit IP as LAN IP
We currently have build options to customize the IP address used in the
preinit phase of the boot process, but not to set the default LAN IP.
Introduce a boolean build option that, when enabled, results in the IP
address configured for the preinit phase, to be also used as the default
LAN IP address.
Robert Marko [Wed, 15 Feb 2023 16:05:30 +0000 (17:05 +0100)]
ipq807x: move AQR driver from built-in to kmod
ipq807x does not compile-in hwmon core, and this is leading to the hwmon
code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON)
evaluating to false as hwmon is being built as a module.
So, lets not compile-in Aquantia PHY driver so it can be included as kmod
instead to have functioning hwmon.
This allows using the thermal sensors in AQR-s as thermal zones for
cooling devices like fans.
Robert Marko [Wed, 15 Feb 2023 15:58:41 +0000 (16:58 +0100)]
kernel: modules: package Aquantia PHY driver
Package the Aquantia AQR PHY driver as kmod.
This enables using the Aquantia driver with hwmon support on targets where
hwmon is not compiled-in.
Currently, in case when AQR driver is compiled-in but hwmon core is not
hwmon code in AQR driver will not get compiled because of macro
IS_REACHABLE(CONFIG_HWMON) evaluating to false.
Rafał Miłecki [Wed, 15 Feb 2023 18:40:38 +0000 (19:40 +0100)]
bcm4908: refactor packet steering init
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Package kmod-ipt-raw enables CONFIG_IP_NF_RAW and packages
iptable_raw.ko
According to kernel's net/netfilter/Kconfig there are only 3 kernel
symbols that depend on the IP_NF_RAW:
1. NETFILTER_XT_TARGET_CT (xt_CT.ko)
2. NETFILTER_XT_TARGET_NOTRACK (unused symbol?!)
3. NETFILTER_XT_TARGET_TRACE (xt_TRACE.ko)
Now: iptables-mod-conntrack-extra selects kmod-ipt-conntrack-extra which
provides: xt_helper.ko nf_conncount.ko xt_connlimit.ko xt_connmark.ko
xt_recent.ko and xt_connbytes.ko (none of them seems to require
iptable_raw.ko).
It seems there is no explicit reason for iptables-mod-conntrack-extra to
require kmod-ipt-raw (iptables_raw.ko).
Rafał Miłecki [Mon, 13 Feb 2023 09:32:45 +0000 (10:32 +0100)]
bcm53xx: refactor packet steering init
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Daniel Golle [Tue, 14 Feb 2023 23:25:19 +0000 (23:25 +0000)]
kernel: import accepted MediaTek Ethernet patches
Import some accepted and pending upstream patches for mtk_eth_soc,
replacing some semantically equivalent local patches and fixing issues
when operating the PCS in 1G SGMII mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 15 Feb 2023 03:06:05 +0000 (03:06 +0000)]
treewide: replace /sys/devices/virtual/ubi by /sys/class/ubi
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Prepare TFTP server with IP address 192.168.11.10
2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and
place it to TFTP directory
3. Hold AOSS (WPS) button and power on WXR-5950AX12
4. WXR-5950AX12 downloads initramfs image from TFTP server and boots
with it automatically
5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade
6. Wait ~120 seconds to complete flashing
- WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for
normal operation and the 2nd one is for recoverying or firmware
upgrading on stock.
- Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*"
partition when booting. This is just a comparation of hash strings.
Behaviors:
- both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover
---> boot from rootfs
- both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover
---> boot from rootfs_recover
Note: this behavior is used for firmware upgrading on stock
- "fw_hash" volume in rootfs is missing
---> boot from rootfs_recover
- "fw_hash" volume in rootfs_recover is missing
---> boot from rootfs
- "fw_hash" volumes in both root* partition are missing
---> boot from rootfs_recover
Reverting to stock firmware:
1. Decrypt official image by buffalo-enc and remove header
1. Boot ApresiaLightGS120GT-SS normally
2. Login to WebUI and open firmware page ("ファームウェア")
3. If the device is booted from image1, set active image for next
booting ("起動イメージ選択") to image2("イメージ2"), press apply
("適用") button and reboot the device to make booting from image2
4. On the WebUI, set active image to image1
5. Select the OpenWrt factory image and press update button ("更新")
6. Open reboot page ("再起動") and press reboot button ("再起動実行")
Notes:
- "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model
number
- this device has 3x GPIO-controlled LEDs on PCB, but 1x LED
("green:unused") has no hole on the case
INAGAKI Hiroshi [Sat, 8 Oct 2022 12:46:51 +0000 (21:46 +0900)]
realtek: add common definition of cameo based firmware
The cameo-related recipes can also be used for APRESIA ApresiaLightGS
series devices. So create common definition for the devices manufactured
by Cameo.
And also, the model name of ApresiaLightGS120GT-SS is too long for cameo
header (max: 20 bytes), so use additional variable "CAMEO_BOARD_MODEL"
in Build/cameo-headers instead of DEVICE_MODEL to use the custom name.
(default of CAMEO_BOARD_MODEL: DEVICE_MODEL)
INAGAKI Hiroshi [Fri, 7 Oct 2022 16:07:17 +0000 (01:07 +0900)]
realtek: rename cameo specific names in "Build/*" definitions
This patch renames some Cameo specific definitions for image generation.
The same format is also used on APRESIA ApresiaLightGS series devices, not
D-Link specific.
Jan Hoffmann [Wed, 8 Feb 2023 21:53:32 +0000 (22:53 +0100)]
realtek: fix memory leak in netevent handler
The net_event_work struct is allocated, but only freed in a single case.
Move the allocation to the branch where it is actually needed, and free
it after the work has been done.
Fixes: 03e1d93e0779 ("realtek: add driver support for routing offload") Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Felix Fietkau [Sat, 10 Dec 2022 13:55:33 +0000 (14:55 +0100)]
mac80211: add fixes for receiving A-MSDU packets on mesh interfaces
The standard defines the A-MSDU header length field differently for mesh
compared to other modes. Deal with this accordingly and work around broken
implementations (e.g. ath10k, ath11k).
Karl Chan [Sun, 29 Jan 2023 05:37:28 +0000 (13:37 +0800)]
ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
1x LAN (blue, configurable)
1x WAN (blue, configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Michael Pratt [Tue, 31 Jan 2023 18:58:38 +0000 (13:58 -0500)]
ath79: add eth0 mac and initvals for Engenius EPG5000
Although VLANs are used, the "eth0" device by itself
does not have a valid MAC, so fix that with preinit script.
More initvals added by editing the driver to print switch registers,
after the bootloader sets them but before openwrt changes them.
The register bits needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written
for example:
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is not similar to "ethaddr"
eth0 *:c8 MAC u-boot-env ethaddr
phy0 *:c8 MAC u-boot-env ethaddr
phy1 *:c9 --- u-boot-env ethaddr +1
WAN *:66:44 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR1200'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
projects / thirdparty / openwrt.git / log
