The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).
Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.
Fix this by cancelling the unthrottle work when shutting down the port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.
Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.
Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.13 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.
Fixes: e81ee637e4ae ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)") Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.19 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c528fcb116e6 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.
Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.
The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.
Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39b412 ("USB: serial: remove
changelogs and old todo entries")).
The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of our machines keeled over trying to rebuild the scheduler domains.
Mainline produces the same splat:
BUG: unable to handle page fault for address: 0000607f820054db
CPU: 2 PID: 149 Comm: kworker/1:1 Not tainted 5.10.0-rc1-master+ #6
Workqueue: events cpuset_hotplug_workfn
RIP: build_sched_domains
Call Trace:
partition_sched_domains_locked
rebuild_sched_domains_locked
cpuset_hotplug_workfn
It happens with cgroup2 and exclusive cpusets only. This reproducer
triggers it on an 8-cpu vm and works most effectively with no
preexisting child cgroups:
tl->mask(cpu), which reads cpu_sibling_map on x86, returns an empty mask
and so cpumask_first() returns >= nr_cpu_ids, which leads to the bogus
value from per_cpu_ptr() above.
The problem is a race between cpuset_hotplug_workfn() and a later
offline of CPU N. cpuset_hotplug_workfn() updates the effective masks
when N is still online, the offline clears N from cpu_sibling_map, and
then the worker uses the stale effective masks that still have N to
generate the scheduling domains, leading the worker to read
N's empty cpu_sibling_map in sd_init().
rebuild_sched_domains_locked() prevented the race during the cgroup2
cpuset series up until the Fixes commit changed its check. Make the
check more robust so that it can detect an offline CPU in any exclusive
cpuset's effective mask, not just the top one.
Fixes: 0ccea8feb980 ("cpuset: Make generate_sched_domains() work with partition") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20201112171711.639541-1-daniel.m.jordan@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to setup its PCI component, the driver needs any node private
instance in order to get a reference to the PCI device and hand that
into edac_pci_create_generic_ctl(). For convenience, it uses the 0th
memory controller descriptor under the assumption that if any, the 0th
will be always present.
However, this assumption goes wrong when the 0th node doesn't have
memory and the driver doesn't initialize an instance for it:
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
ecdh_set_secret() casts a void* pointer to a const u64* in order to
feed it into ecc_is_key_valid(). This is not generally permitted by
the C standard, and leads to actual misalignment faults on ARMv6
cores. In some cases, these are fixed up in software, but this still
leads to performance hits that are entirely avoidable.
So let's copy the key into the ctx buffer first, which we will do
anyway in the common case, and which guarantees correct alignment.
Perf event attritube supports exclude_kernel flag to avoid
sampling/profiling in supervisor state (kernel). Based on this event
attr flag, Monitor Mode Control Register bit is set to freeze on
supervisor state. But sometimes (due to hardware limitation), Sampled
Instruction Address Register (SIAR) locks on to kernel address even
when freeze on supervisor is set. Patch here adds a check to drop
those samples.
According to the event list from icelake_core_v1.09.json, the encoding
of the RTM_RETIRED.ABORTED event on Ice Lake should be,
"EventCode": "0xc9",
"UMask": "0x04",
"EventName": "RTM_RETIRED.ABORTED",
The event CYCLE_ACTIVITY.STALLS_MEM_ANY (0x14a3) should be available on
all 8 GP counters on ICL, but it's only scheduled on the first four
counters due to the current ICL constraint table.
Add a line for the CYCLE_ACTIVITY.STALLS_MEM_ANY event in the ICL
constraint table.
Correct the comments for the CYCLE_ACTIVITY.CYCLES_MEM_ANY event.
I have had reports from two different people that attempts to read the
analog input channels of the MF624 board fail with an `ETIMEDOUT` error.
After triggering the conversion, the code calls `comedi_timeout()` with
`mf6x4_ai_eoc()` as the callback function to check if the conversion is
complete. The callback returns 0 if complete or `-EBUSY` if not yet
complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not
completed within a timeout period which is propagated as an error to the
user application.
The existing code considers the conversion to be complete when the EOLC
bit is high. However, according to the user manuals for the MF624 and
MF634 boards, this test is incorrect because EOLC is an active low
signal that goes high when the conversion is triggered, and goes low
when the conversion is complete. Fix the problem by inverting the test
of the EOLC bit state.
The cx2072x codec driver defines multiple DAIs with the same stream
name "Playback" and "Capture". Although the current code works more
or less as is as the secondary streams are never used, it still leads
the error message like:
debugfs: File 'Playback' in directory 'dapm' already present!
debugfs: File 'Capture' in directory 'dapm' already present!
Fix it by renaming the secondary streams to unique names.
Fixes: a497a4363706 ("ASoC: Add support for Conexant CX2072X CODEC") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20201208135154.9188-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a per-transaction flag to indicate that the buffer
must be cleared when the transaction is complete to
prevent copies of sensitive data from being preserved
in memory.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration") Cc: stable@vger.kernel.org #5.3 Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diag308 subcode 0 performes a clear reset which inlcudes the reset of
all registers in the system. While this is the preferred behavior when
loading a normal kernel via kexec it prevents the crash kernel to store
the register values in the dump. To prevent this use subcode 1 when
loading a crash kernel instead.
Fixes: ee337f5469fd ("s390/kexec_file: Add crash support to image loader") Cc: <stable@vger.kernel.org> # 4.17 Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Reported-by: Xiaoying Yan <yiyan@redhat.com> Tested-by: Lianbo Jiang <lijiang@redhat.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not resetting the SMT siblings might leave them in unpredictable
state. One of the observed problems was that the CPU timer wasn't
reset and therefore large system time values where accounted during
CPU bringup.
Since mmap for userspace is based on page alignment, add page alignment
for iram alloc from pool, otherwise, some good data located in the same
page of dmab->area maybe touched wrongly by userspace like pulseaudio.
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
The Quanta NL3 laptop has both a headphone output jack and a headset
jack, on the right edge of the chassis.
The pin information suggests that both of these are at the Front.
The PulseAudio is confused to differentiate them so one of the jack
can neither get the jack sense working nor the audio output.
The ALC269_FIXUP_LIFEBOOK chained with ALC269_FIXUP_QUANTA_MUTE can
help to differentiate 2 jacks and get the 'Auto-Mute Mode' working
correctly.
This Acer Veriton N4640G/N6640G/N2510G desktops have 2 headphone
jacks(front and rear), and a separate Mic In jack.
The rear headphone jack is actually a line out jack but always silent
while playing audio. The front 'Mic In' also fails the jack sensing.
Apply the ALC269_FIXUP_LIFEBOOK to have all audio jacks to work as
expected.
Signed-off-by: Chris Chiu <chiu@endlessos.org> Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201222150459.9545-2-chiu@endlessos.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few places that call round{up|down}_pow_of_two() with the
value zero, and this causes undefined behavior warnings. Avoid
calling those macros if such a nonsense value is passed; it's a minor
optimization as well, as we handle it as either an error or a value to
be skipped, instead.
This change could fix 2 issues on this machine:
- the bass speaker's output volume can't be adjusted, that is because
the bass speaker is routed to the DAC (Nid 0x6) which has no volume
control.
- after plugging a headset with vol+, vol- and pause buttons on it,
press those buttons, nothing happens, this means those buttons
don't work at all. This machine has alc287 codec, need to add the
codec id to the disable/enable_headset_jack_key(), then the headset
button could work.
The quirk of ALC285_FIXUP_THINKPAD_HEADSET_JACK could fix both of these
2 issues.
The Windows driver sets the pincfg for the AE-5's rear-headphone to
report as a microphone. This causes issues with Pulseaudio mistakenly
believing there is no headphone plugged in. In Linux, we should instead
set it to be a headphone.
It seems that the HD-audio clear and reconfig sysfs don't work any
longer after the recent driver core change. There are multiple issues
around that: the linked list corruption and the dead device handling.
The former issue is fixed by another patch for the driver core itself,
while the latter patch needs to be addressed in HD-audio side.
This patch corresponds to the latter, it recovers those broken
functions by replacing the device detach and attach actions with the
standard core API functions, which are almost equivalent with unbind
and bind actions.
Recently we met a touchscreen problem on some Thinkpad machines, the
touchscreen driver (i2c-hid) is not loaded and the touchscreen can't
work.
An i2c ACPI device with the name WACF2200 is defined in the BIOS, with
the current rule in matching_id(), this device will be regarded as
a PNP device since there is WACFXXX in the acpi_pnp_device_ids[] and
this PNP device is attached to the acpi device as the 1st
physical_node, this will make the i2c bus match fail when i2c bus
calls acpi_companion_match() to match the acpi_id_table in the i2c-hid
driver.
WACF2200 is an i2c device instead of a PNP device, after adding the
string length comparing, the matching_id() will return false when
matching WACF2200 and WACFXXX, and it is reasonable to compare the
string length when matching two IDs.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching this function to AE_CTRL_TERMINATE broke the documented
behaviour of acpi_dev_get_resources() - AE_CTRL_TERMINATE does not, in
fact, terminate the resource walk because acpi_walk_resource_buffer()
ignores it (specifically converting it to AE_OK), referring to that
value as "an OK termination by the user function". This means that
acpi_dev_get_resources() does not abort processing when the preproc
function returns a negative value.
Signed-off-by: Daniel Scally <djrscally@gmail.com> Cc: 3.10+ <stable@vger.kernel.org> # 3.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to
be reference counted for wakeup enabling, because they may be enabled
to signal wakeup on behalf of their subordinate devices and that
may happen for multiple times in a row, whereas for the other devices
it only makes sense to enable wakeup signaling once.
However, this becomes problematic if the bridge itself is suspended,
because it is treated as a "regular" device in that case and the
reference counting doesn't work.
For instance, suppose that there are two devices below a bridge and
they both can signal wakeup. Every time one of them is suspended,
wakeup signaling is enabled for the bridge, so when they both have
been suspended, the bridge's wakeup reference counter value is 2.
Say that the bridge is suspended subsequently and acpi_pci_wakeup()
is called for it. Because the bridge can signal wakeup, that
function will invoke acpi_pm_set_device_wakeup() to configure it
and __acpi_pm_set_device_wakeup() will be called with the last
argument equal to 1. This causes __acpi_device_wakeup_enable()
invoked by it to omit the reference counting, because the reference
counter of the target device (the bridge) is 2 at that time.
Now say that the bridge resumes and one of the device below it
resumes too, so the bridge's reference counter becomes 0 and
wakeup signaling is disabled for it, but there is still the other
suspended device which may need the bridge to signal wakeup on its
behalf and that is not going to work.
To address this scenario, use wakeup enable reference counting for
all devices, not just for bridges, so drop the last argument from
__acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(),
which causes acpi_pm_set_device_wakeup() and
acpi_pm_set_bridge_wakeup() to become identical, so drop the latter
and use the former instead of it everywhere.
If the call to spi_register_master() fails on probe of the NetUP
Universal DVB driver, the spi_master struct is erroneously not freed.
Likewise, if spi_new_device() fails, the spi_controller struct is
not unregistered. Plug the leaks.
While at it, fix an ordering issue in netup_spi_release() wherein
spi_unregister_master() is called after fiddling with the IRQ control
register. The correct order is to call spi_unregister_master() *before*
this teardown step because bus accesses may still be ongoing until that
function returns.
If a user holds a button down on a remote, then no ir idle interrupt will
be generated until the user releases the button, depending on how quickly
the remote repeats. No IR is processed until that point, which means that
holding down a button may not do anything.
This also resolves an issue on a Cubieboard 1 where the IR receiver is
picking up ambient infrared as IR and spews out endless
"rc rc0: IR event FIFO is full!" messages unless you choose to live in
the dark.
Cc: stable@vger.kernel.org Tested-by: Hans Verkuil <hverkuil@xs4all.nl> Acked-by: Maxime Ripard <mripard@kernel.org> Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gspca driver leaks memory when a probe fails. gspca_dev_probe2()
calls v4l2_device_register(), which takes a reference to the
underlying device node (in this case, a USB interface). But the
failure pathway neglects to call v4l2_device_unregister(), the routine
responsible for dropping this reference. Consequently the memory for
the USB interface and its device never gets released.
We execute certain NPU2 setup code (such as mapping an LPID to a device
in NPU2) unconditionally if an Nvlink bridge is detected. However this
cannot succeed on POWER8NVL machines as the init helpers return an error
other than ENODEV which means the device is there is and setup failed so
vfio_pci_enable() fails and pass through is not possible.
This changes the two NPU2 related init helpers to return -ENODEV if
there is no "memory-region" device tree property as this is
the distinction between NPU and NPU2.
There is only one function in init/initramfs.c that is in the .text
section, and it is marked __weak. When building with clang-12 and the
integrated assembler, this leads to a bug with recordmcount:
./scripts/recordmcount "init/initramfs.o"
Cannot find symbol for section 2: .text.
init/initramfs.o: failed
I'm not quite sure what exactly goes wrong, but I notice that this
function is only ever called from an __init function, and normally
inlined. Marking it __init as well is clearly correct and it leads to
recordmcount no longer complaining.
To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.
Release dmabuf reference before returning from kfd_ioctl_import_dmabuf.
amdgpu_amdkfd_gpuvm_import_dmabuf takes a reference to the underlying
GEM BO and doesn't keep the reference to the dmabuf wrapper.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
At very high pixel clock, bandwidth calculation exceeds 32 bit size
and overflow value. This causes the resulting selection of link rate
to be inaccurate.
[How]
Change order of operation and use fixed point to deal with integer
accuracy. Also address bug found when forcing link rate.
Signed-off-by: Chris Park <Chris.Park@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Eryk Brol <eryk.brol@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The per-cpu bpf_redirect_info is shared among all skb_do_redirect()
and BPF redirect helpers. Callers on RX path are all in BH context,
disabling preemption is not sufficient to prevent BH interruption.
In production, we observed strange packet drops because of the race
condition between LWT xmit and TC ingress, and we verified this issue
is fixed after we disable BH.
Although this bug was technically introduced from the beginning, that
is commit 3a0af8fd61f9 ("bpf: BPF for lightweight tunnel infrastructure"),
at that time call_rcu() had to be call_rcu_bh() to match the RCU context.
So this patch may not work well before RCU flavor consolidation has been
completed around v5.0.
Update the comments above the code too, as call_rcu() is now BH friendly.
Namespaced file capabilities were introduced in 8db6c34f1dbc .
When userspace reads an xattr for a namespaced capability, a
virtualized representation of it is returned if the caller is
in a user namespace owned by the capability's owning rootid.
The function which performs this virtualization was not hooked
up if CONFIG_SECURITY=n. Therefore in that case the original
xattr was shown instead of the virtualized one.
"setcap -v" verifies the values instead of setting them, and
will check whether the rootid value is set. Therefore, with
this bug un-fixed, and with CONFIG_SECURITY=n, setcap -v will
fail:
The Allwinner V3 SoC shares the same base as the V3s but comes with
extra pins and features available. As a result, it has its dedicated
compatible string (already used in device trees), which is added here.
The argv_split() function must be paired with argv_free(), else we must
keep a reference to the argv array received or do the freeing ourselves,
in synthesize_sdt_probe_command() we were simply leaking that argv[]
array.
Fixes: 3b1f8311f6963cd1 ("perf probe: Add sdt probes arguments into the uprobe cmd string") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexandre Truong <alexandre.truong@arm.com> Cc: Alexis Berlemont <alexis.berlemont@gmail.com> Cc: He Zhe <zhe.he@windriver.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20201224135139.GF477817@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
$(error-if,...) is expanded to an empty string. Currently, it relies on
eval_clause() returning xstrdup("") when all attempts for expansion fail,
but the correct implementation is to make do_error_if() return xstrdup("").
Two clock divider tables are missing sentinel at the end. Effect of that
is that clock framework reads past the last entry. Fix that with adding
sentinel at the end.
The "vq" struct is added to the "vdev->vqs" list prematurely. If we
encounter an error later in the function then the "vq" is freed, but
since it is still on the list that could lead to a use after free bug.
Fixes: cbeedb72b97a ("virtio_ring: allocate desc state for split ring separately") Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de> Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X8pGaG/zkI3jk8mk@mwanda Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set a negative error code intead of returning success if the MTU has
been changed to something invalid.
Fixes: fe36cbe0671e ("virtio_net: clear MTU when out of range") Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de> Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X8pGVJSeeCdII1Ys@mwanda Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a copy and paste bug in the error handling of this code and
it uses "ring_dma_addr" three times instead of "device_event_dma_addr"
and "driver_event_dma_addr".
Fixes: 1ce9e6055fa0 (" virtio_ring: introduce packed ring support") Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de> Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X8pGRJlEzyn+04u2@mwanda Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using 'perf record's option '-I' or '--user-regs=' along with
argument '?' to list available register names, memory of variable 'os'
allocated by strdup() needs to be released before __parse_regs()
returns, otherwise memory leak will occur.
Fixes: bcc84ec65ad1 ("perf record: Add ability to name registers to record") Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Li Bin <huawei.libin@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20200703093344.189450-1-zhengzengkai@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there are other PWM controllers enabled along with pwm-lp3943,
pwm-lp3942 is failing to probe with -EEXIST error. This is because
other PWM controllers are probed first and assigned PWM base 0 and
pwm-lp3943 is requesting for 0 again.
In order to avoid this, assign the chip base with -1, so that it is
dynamically allocated.
clang produces a build failure in configurations without COMMON_CLK
when a timeout calculation goes wrong:
arm-linux-gnueabi-ld: drivers/watchdog/coh901327_wdt.o: in function `coh901327_enable':
coh901327_wdt.c:(.text+0x50): undefined reference to `__bad_udelay'
Add a Kconfig dependency to only do build testing when COMMON_CLK
is enabled.
The use of msleep() in the restart handler will cause scheduler to
induce a context switch which is not desirable. This generates below
warning on SDX55 when WDT is the only available restart source:
[ 39.800188] reboot: Restarting system
[ 39.804115] ------------[ cut here ]------------
[ 39.807855] WARNING: CPU: 0 PID: 678 at kernel/rcu/tree_plugin.h:297 rcu_note_context_switch+0x190/0x764
[ 39.812538] Modules linked in:
[ 39.821954] CPU: 0 PID: 678 Comm: reboot Not tainted 5.10.0-rc1-00063-g33a9990d1d66-dirty #47
[ 39.824854] Hardware name: Generic DT based system
[ 39.833470] [<c0310fbc>] (unwind_backtrace) from [<c030c544>] (show_stack+0x10/0x14)
[ 39.838154] [<c030c544>] (show_stack) from [<c0c218f0>] (dump_stack+0x8c/0xa0)
[ 39.846049] [<c0c218f0>] (dump_stack) from [<c0322f80>] (__warn+0xd8/0xf0)
[ 39.853058] [<c0322f80>] (__warn) from [<c0c1dc08>] (warn_slowpath_fmt+0x64/0xc8)
[ 39.859925] [<c0c1dc08>] (warn_slowpath_fmt) from [<c038b6f4>] (rcu_note_context_switch+0x190/0x764)
[ 39.867503] [<c038b6f4>] (rcu_note_context_switch) from [<c0c2aa3c>] (__schedule+0x84/0x640)
[ 39.876685] [<c0c2aa3c>] (__schedule) from [<c0c2b050>] (schedule+0x58/0x10c)
[ 39.885095] [<c0c2b050>] (schedule) from [<c0c2eed0>] (schedule_timeout+0x1e8/0x3d4)
[ 39.892135] [<c0c2eed0>] (schedule_timeout) from [<c039ad40>] (msleep+0x2c/0x38)
[ 39.899947] [<c039ad40>] (msleep) from [<c0a59d0c>] (qcom_wdt_restart+0xc4/0xcc)
[ 39.907319] [<c0a59d0c>] (qcom_wdt_restart) from [<c0a58290>] (watchdog_restart_notifier+0x18/0x28)
[ 39.914715] [<c0a58290>] (watchdog_restart_notifier) from [<c03468e0>] (atomic_notifier_call_chain+0x60/0x84)
[ 39.923487] [<c03468e0>] (atomic_notifier_call_chain) from [<c030ae64>] (machine_restart+0x78/0x7c)
[ 39.933551] [<c030ae64>] (machine_restart) from [<c0348048>] (__do_sys_reboot+0xdc/0x1e0)
[ 39.942397] [<c0348048>] (__do_sys_reboot) from [<c0300060>] (ret_fast_syscall+0x0/0x54)
[ 39.950721] Exception stack(0xc3e0bfa8 to 0xc3e0bff0)
[ 39.958855] bfa0: 0001221cbed2fe24fee1dead281219690123456700000000
[ 39.963832] bfc0: 0001221cbed2fe240000000300000058000225e0000000000000000000000000
[ 39.971985] bfe0: b6e62560bed2fc8400010fd8b6e62580
[ 39.980124] ---[ end trace 3f578288bad866e4 ]---
Hence, replace msleep() with mdelay() to fix this issue.
The ndo_start_xmit() method must not attempt to free the skb to transmit
when returning NETDEV_TX_BUSY. Therefore, make sure the
korina_send_packet() function returns NETDEV_TX_OK when it frees a packet.
Fixes: ef11291bcd5f ("Add support the Korina (IDT RC32434) Ethernet MAC") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201214220952.19935-1-vincent.stehle@laposte.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even if there is more rx data waiting on the chip, the rx napi poll fn
will never run more than once - it will always read a few buffers, then
bail out and re-arm interrupts. Which results in ping-pong between napi
and interrupt.
This defeats the purpose of napi, and is bad for performance.
Fix by making the rx napi poll behave identically to other ethernet
drivers:
1. initialize rx napi polling with an arbitrary budget (64).
2. in the polling fn, return full weight if rx queue is not depleted,
this tells the napi core to "keep polling".
3. update the rx tail ("ring the doorbell") once for every 8 processed
rx ring buffers.
Thanks to Jakub Kicinski, Eric Dumazet and Andrew Lunn for their expert
opinions and suggestions.
Tested with 20 seconds of full bandwidth receive (iperf3):
rx irqs softirqs(NET_RX)
-----------------------------
before 23827 33620
after 129 4081
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430 Fixes: 23f0703c125be ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com> Link: https://lore.kernel.org/r/20201215161954.5950-1-TheSven73@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an unescaped left brace in a regex in OPEN_BRACE check. This
throws a runtime error when checkpatch is run with --fix flag and the
OPEN_BRACE check is executed.
Fix it by escaping the left brace.
Link: https://lkml.kernel.org/r/20201115202928.81955-1-dwaipayanray1@gmail.com Fixes: 8d1824780f2f ("checkpatch: add --fix option for a couple OPEN_BRACE misuses") Signed-off-by: Dwaipayan Ray <dwaipayanray1@gmail.com> Acked-by: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On 2-node NUMA hosts we see bursts of kswapd reclaim and subsequent
pressure spikes and stalls from cache refaults while there is plenty of
free memory in the system.
Usually, kswapd is woken up when all eligible nodes in an allocation are
full. But the code related to watermark boosting can wake kswapd on one
full node while the other one is mostly empty. This may be justified to
fight fragmentation, but is currently unconditionally done whether
watermark boosting is occurring or not.
In our case, many of our workloads' throughput scales with available
memory, and pure utilization is a more tangible concern than trends
around longer-term fragmentation. As a result we generally disable
watermark boosting.
Wake kswapd only woken when watermark boosting is requested.
Link: https://lkml.kernel.org/r/20201020175833.397286-1-hannes@cmpxchg.org Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The page has just been allocated, so its refcount is 1. free_unref_page()
is for use on pages which have a zero refcount. Use __free_page() like
the other implementations of pte_alloc_one().
Link: https://lkml.kernel.org/r/20201125034655.27687-1-willy@infradead.org Fixes: 1ae9ae5f7df7 ("sparc: handle pgtable_page_ctor() fail") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As part of the cma_dev release, that pointer will be set to NULL. In case
it happens in rdma_bind_addr() (part of an error flow), the next call to
addr_handler() will have a call to cma_acquire_dev_by_src_ip() which will
overwrite sgid_attr without releasing it.
When receiving pages data, return value 'ret' when positive includes
`buf->page_base`, so we should subtract that before it is used for
changing `offset` and comparing against `want`.
This was discovered on the very rare cases where the server returned a
chunk of bytes that when added to the already received amount of bytes
for the pages happened to match the current `recv.len`, for example
on this case:
buf->page_base : 258356
actually received from socket: 1740
ret : 260096
want : 260096
In this case neither of the two 'if ... goto out' trigger, and we
continue to tail parsing.
Worth to mention that the ensuing EMSGSIZE from the continued execution of
`xs_read_xdr_buf` may be observed by an application due to 4 superfluous
bytes being added to the pages data.
Fixes: 277e4ab7d530 ("SUNRPC: Simplify TCP receive code by switching to using iterators") Signed-off-by: Dan Aloni <dan@kernelim.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xterm serial channel was leaking a fd used in setting up the
port helper
This bug is prehistoric - it predates switching to git. The "fixes"
header here is really just to mark all the versions we would like this to
apply to which is "Anything from the Cretaceous period onwards".
No dinosaurs were harmed in fixing this bug.
Fixes: b40997b872cd ("um: drivers/xterm.c: fix a file descriptor leak") Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a logical error in tty reading. We get 0 and errno == EAGAIN
on the first attempt to read from a closed file descriptor.
Compared to that a true EAGAIN is EAGAIN and -1.
If we check errno for EAGAIN first, before checking the return
value we miss the fact that the descriptor is closed.
This bug is as old as the driver. It was not showing up with
the original POLL based IRQ controller, because it was
producing multiple events. Switching to EPOLL unmasked it.
Fixes: ff6a17989c08 ("Epoll based IRQ controller") Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to return PTR_ERR() error code from the error handling case where
ubifs_hash_get_desc() failed instead of 0 in ubifs_init_authentication(),
as done elsewhere in this function.
Fixes: 49525e5eecca5 ("ubifs: Add helper functions for authentication support") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
A reboot notifier, which stops the WDT by calling the stop hook without
any check, would be registered when we set WDOG_STOP_ON_REBOOT flag.
Howerer we allow the WDT driver to omit the stop hook since commit
"d0684c8a93549" ("watchdog: Make stop function optional") and provide
a module parameter for user that controls the WDOG_STOP_ON_REBOOT flag
in commit 9232c80659e94 ("watchdog: Add stop_on_reboot parameter to
control reboot policy"). Together that commits make user potential to
insert a watchdog driver that don't provide a stop hook but with the
stop_on_reboot parameter set, then dereferencing of null pointer occurs
on system reboot.
Check the stop hook before registering the reboot notifier to fix the
issue.
Fixes: d0684c8a9354 ("watchdog: Make stop function optional") Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20201109130512.28121-1-wangwensheng4@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the specification described, users must check busy bit before start
a new loading operation to make sure that the previous loading is done
and the device is ready to accept a new one.
sprd_wdt_start() would return fail if the loading operation is not completed
in a certain time, disabling watchdog for that case would probably cause
the kernel crash when kick watchdog later, that's too bad, so remove the
watchdog disable operation for the fail case to make sure other parts in
the kernel can run normally.
The error handling frees "ctl" but it's still on the "dsp->ctl_list"
list so that could result in a use after free. Remove it from the list
before returning.
Fixes: 2323736dca72 ("ASoC: wm_adsp: Add basic support for rev 1 firmware file format") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/X9B0keV/02wrx9Xs@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we set up a TDLS station, we set sta->sta.bandwidth solely based
on the capabilities, because the "what's the current bandwidth" check
is bypassed and only applied for other types of stations.
This leads to the unfortunate scenario that the sta->sta.bandwidth is
160 MHz if both stations support it, but we never actually configure
this bandwidth unless the AP is already using 160 MHz; even for wider
bandwidth support we only go up to 80 MHz (at least right now.)
For iwlwifi, this can also lead to firmware asserts, telling us that
we've configured the TX rates for a higher bandwidth than is actually
available due to the PHY configuration.
For non-TDLS, we check against the interface's requested bandwidth,
but we explicitly skip this check for TDLS to cope with the wider BW
case. Change this to
(a) still limit to the TDLS peer's own chandef, which gets factored
into the overall PHY configuration we request from the driver,
and
(b) limit it to when the TDLS peer is authorized, because it's only
factored into the channel context in this case.
projects / thirdparty / kernel / stable.git / log
