ramips: mt7621: harmonize naming scheme for Mikrotik
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allows proper usage of the ss tool. Otherwise, several errors and bad
data gets thrown:
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Originally reported here: https://github.com/openwrt/packages/issues/8232
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Dan Haab [Mon, 6 Apr 2020 23:14:39 +0000 (16:14 -0700)]
bcm53xx: add support for Luxul FullMAC WiFi devices
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.
Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.
use stock_mac art_loc
lan :f2 0x0
wan :f3 0x1002
5g :f4 0x6
2g :f5 0x5006
Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hans Dedecker [Sun, 5 Apr 2020 20:26:33 +0000 (22:26 +0200)]
ppp: update to version 2.4.8.git-2020-03-21
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141) 6b014be pppd: Print version information to stdout instead of stderr (#133) cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined ae54fcf pppd: Obfuscate password argument string 8d45443 pppd: Ignore received EAP messages when not doing EAP 8d7970b pppd: Fix bounds check in EAP code 858976b radius: Prevent buffer overflow in rc_mksid()
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bump to 2.81rc5 and re-work ipset-remove-old-kernel-support.
More runtime kernel version checking is done in 2.81rc5 in various parts
of the code, so expand the ipset patch' scope to inlude those new areas
and rename to something a bit more generic.:wq
Upstream changes from rc4
532246f Tweak to DNSSEC logging. 8caf3d7 Fix rare problem allocating frec for DNSSEC. d162bee Allow overriding of ubus service name. b43585c Fix nameserver list in auth mode. 3f60ecd Fixed resource leak on ubus_init failure. 0506a5e Handle old kernels that don't do NETLINK_NO_ENOBUFS. e7ee1aa Extend stop-dns-rebind to reject IPv6 LL and ULA addresses. We also reject the loopback address if rebind-localhost-ok is NOT set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.
[1] 2a82e0e1ca0f ("ipq806x: switch to 4.19 kernel version")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
hostapd: Move hostapd variants to WirelessAPD menu
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name] Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
INAGAKI Hiroshi [Mon, 30 Mar 2020 06:19:50 +0000 (15:19 +0900)]
kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATE
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.
We should use the same way.
ref (RTL8367B):
- ASUS RT-N56U
- TP-Link Archer C2 v1
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.
DENG Qingfang [Sat, 4 Apr 2020 04:10:32 +0000 (12:10 +0800)]
generic: mt7530: fix null pointer dereferencing in port5 setup
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 19 Mar 2020 11:33:27 +0000 (19:33 +0800)]
ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 18 Mar 2020 15:38:58 +0000 (23:38 +0800)]
ramips: mt7621: update dts/defconfig for DSA
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.
Removed because of the new NAND driver:
- 0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch
- 0039-mtd-add-mt7621-nand-support.patch
- 0040-nand-hack.patch
Remove patch that no longer applies (needs rework):
- 0034-NET-multi-phy-support.patch
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Fri, 17 Jan 2020 08:04:14 +0000 (16:04 +0800)]
ramips: mtk-mmc: set correct DMA mask
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Tan Zien [Sun, 5 Jan 2020 21:16:43 +0000 (05:16 +0800)]
kernel: add module for Mellanox mlx Network Driver
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards
Tim Harvey [Wed, 1 Apr 2020 17:23:12 +0000 (10:23 -0700)]
imx6: bootscript: use partition UUID for rootfs if possible
Specifying root filesystem by device is non-deterministic for several
reasons:
- USB device unmeration order is not garunteeed for USB storage devs
- MMC devs ordering is determined by the instance of the MMC host
controller including non-storage SDIO devices which can throw off
numbering depending on kernel versions.
Paul Spooren [Thu, 12 Mar 2020 22:55:41 +0000 (12:55 -1000)]
build: refactor JSON info files to `profiles.json`
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6e2
("build: create JSON files containing image info").
They are useful for firmware wizards and script checking for
reproducibility.
Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.
This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.
Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.
Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.
As before, this creation is enabled by default only if `BUILDBOT` is set.
Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.
Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE
Suggested-by: 李国 <uxgood.org@gmail.com> Acked-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Daniel Golle [Mon, 30 Mar 2020 22:35:04 +0000 (23:35 +0100)]
mac80211: rt2x00: prune more unnecessary exports
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There were two changes between 1.1.1e and 1.1.1f:
- a change in BN prime generation to avoid possible fingerprinting of
newly generated RSA modules
- the patch reversing EOF detection we had already applied.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Tue, 31 Mar 2020 19:27:11 +0000 (20:27 +0100)]
oxnas: fix warning in SATA driver
drivers/ata/sata_oxnas.c: In function 'sata_oxnas_port_irq':
drivers/ata/sata_oxnas.c:2126:25: warning: left shift count >= width of type [-Wshift-count-overflow]
if (ap->qc_active & (1 << ATA_TAG_INTERNAL)) {
^~
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Tue, 31 Mar 2020 14:03:55 +0000 (16:03 +0200)]
ipq40xx: fix DAP-2610 boot failure
Albert has reported, that his DAP-2610 wont boot with the latest
snapshot and Fredrik has found out, that the device gets stuck at
"Waiting for root device ..." due to missing 5.4 kernel config symbol
CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel
version bump.
Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed Fixes: 272e0a702a2b ("ipq40xx: add v5.4 support") Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
李国 [Thu, 26 Mar 2020 06:05:33 +0000 (14:05 +0800)]
x86: generate EFI platform bootable images
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
李国 [Thu, 26 Mar 2020 05:47:40 +0000 (13:47 +0800)]
firmware-utils: ptgen: add GPT support
Add GPT support to ptgen, so we can generate EFI bootable images.
Introduced two options:
-g generate GPT partition table
-G GUID use GUID for disk and increase last bit for all partitions
We drop The alternate partition table to reduce size, This may cause
problems when generate vmdk images or vdi images. We have to pad enough
sectors when generate these images.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[fixed compilation on macOS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* queueing: backport skb_reset_redirect change from 5.6
* version: bump
This release has only one slight change, to put it closer to the 5.6
codebase, but its main purpose is to bump us to a 1.0.y version number.
Now that WireGuard 1.0.0 has been released for Linux 5.6 [1], we can put
the same number on the backport compat codebase.
When OpenWRT bumps to Linux 5.6, we'll be able to drop this package
entirely, which I look forward to seeing.
Yousong Zhou [Tue, 3 Mar 2020 15:09:47 +0000 (23:09 +0800)]
generic: mips: exclude more dsemul code when fpu-emu is not enabled
The patch is backported from mips-next. In addition to minor reduction
of code size and runtime memory use, the more apparent difference is
that the delay slot emulation page will not be present for those targets
with fpu emulation disabled (CONFIG_MIPS_FP_SUPPORT=n)
Memory maps of busybox before and after this change
Georgi Vlaev [Fri, 27 Mar 2020 10:33:53 +0000 (12:33 +0200)]
tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)
The last couple of TP-Link firmware releases for Archer C6 v2 (EU)
have switched to version 1.2.x. Bump the soft_ver to "1.2.1" to
allow firmware updates from the vendor web interface.
Jose Olivera [Sat, 28 Mar 2020 16:11:36 +0000 (00:11 +0800)]
ath10k-ct: Support AQL on ath10k CT_KVER-5.4
Commit ea50780 backported Airtime Queue Limits (AQL) from Linux 5.5
to OpenWrt's backports 5.4. However, this only enabled AQL for the
vanilla ath10k driver. This patch also enables it for ath10k-ct.
Tested on:
* 2xTP-Link Archer A7v5 (QCA9563/QCA988X)
* Backports version 5.4-rc8 & 5.4.27
* ath10k-ct and ath10k-ct-htt firmware version 014 to 017
* ath10k-ct driver versions dc025dc to 3d173a4 (CT_KVER-5.4)
* WPA2, 802.11krv
Tested since January 25, 2020.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
Nick Hainke [Tue, 24 Mar 2020 22:12:01 +0000 (23:12 +0100)]
hostapd: add abridged flag in disassoc_imminent
If the abridged flag is set to 1 the APs that are listed in the BSS
Transition Candidate List are prioritized. If the bit is not set, the
APs have the same prioritization as the APs that are not in the list.
If you want to steer a client, you should set the flag!
The flag can be set by adding {...,'abridged': true,...} to the normal
ubus call.
Replace the build time choice of json support with a package based
choice. Users requiring a json aware version of 'nft' may now install
nftables-json.
The default choice to fulfill the 'nftables' package dependency is
'nftables-nojson'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
projects / thirdparty / openwrt.git / log
