Felix Fietkau [Wed, 19 Feb 2014 19:20:10 +0000 (19:20 +0000)]
gcc: prevent the use of LDRD/STRD on ARMv5TE
These instructions are for 64-bit load/store. On ARMv5TE, the CPU
requires addresses to be aligned to 64-bit. When misaligned, behavior is
undefined (effectively either loads the same word twice on LDRD, or
corrupts surrounding memory on STRD).
On ARMv6 and newer, unaligned access is safe.
Removing these instructions for ARMv5TE is necessary, because GCC
ignores alignment information in pointers and does unsafe optimizations
that have shown up as bugs in various places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39638
Gabor Juhos [Wed, 19 Feb 2014 12:15:34 +0000 (12:15 +0000)]
ar71xx: add user-space support for TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code] Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
Luka Perkov [Sat, 15 Feb 2014 23:53:10 +0000 (23:53 +0000)]
kirkwood: update support for dockstar
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-dockstar-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> Tested-by: Alexander Couzens <lynxis@fe80.eu> CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39593
Luka Perkov [Sat, 15 Feb 2014 23:53:09 +0000 (23:53 +0000)]
kirkwood: update support for ib62x0
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-ib62x0-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> Tested-by: Luka Perkov <luka@openwrt.org> CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39592
Luka Perkov [Sat, 15 Feb 2014 23:53:08 +0000 (23:53 +0000)]
kirkwood: update support for iconnect
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39591
Some users are avoiding to replace their bootloader, because of that add
support for second stage u-boot image. Having ubifs capable bootloader is
required in order to boot current OpenWrt trunk.
Sample ib62x0 commands for running second stage bootloader:
While at it include parallel build support, use alphabetic order of the boards
and introduce common OpenWrt configuration.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by (on ib62x0): Luka Perkov <luka@openwrt.org>
Tested-by (on dockstar): Alexander Couzens <lynxis@fe80.eu>
Tested-by (on iconnect): Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Felix Kaechele <heffer@fedoraproject.org> CC: Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Alexander Couzens <lynxis@fe80.eu> CC: Daniel Engberg <daniel.engberg@pyret.net> CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39590
Jo-Philipp Wich [Thu, 13 Feb 2014 21:19:00 +0000 (21:19 +0000)]
ar71xx: fix mtdpartsize macro in image Makefile (#14961)
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).
Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.
Luka Perkov [Tue, 11 Feb 2014 02:07:46 +0000 (02:07 +0000)]
mvebu: update kernel config
The config-3.10 doesn't specify the configuration of the backported PCI
features, and the Marvell EBU Device Bus Controller, this will prevent
a clean compile. This patch enables these features to archive a clean compile
without having to specify the state of these configuration after starting to
compile.
Luka Perkov [Tue, 11 Feb 2014 02:07:44 +0000 (02:07 +0000)]
mvebu: backport mainline patches from kernel 3.13
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.12, and Linux v3.13.
This work mainly covers:
* Finishes work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family, and the Armada family.
* timer initialization update, and access function for the Armada family.
* Generic IRQ handling backporting.
* Some bug fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com> CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39566
Luka Perkov [Tue, 11 Feb 2014 02:07:41 +0000 (02:07 +0000)]
mvebu: backport mainline patches from kernel 3.12
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.11, and Linux v3.12.
This work mainly covers:
* Ground work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family,and the Armada family.
* Further updates to the mvebu MBus.
* Work and ground work for enabling MSI on the Armada family.
* some phy / mdio bus initialization related work.
* Device tree binding documentation update.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com> CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39565
Luka Perkov [Tue, 11 Feb 2014 02:07:38 +0000 (02:07 +0000)]
mvebu: backport mainline patches from kernel 3.11
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.10, and Linux v3.11.
This work mainly covers:
* Enabling USB storage, and PCI to mvebu_defconfig.
* Add support for NOR flash.
* Some PCI device tree related updates, and bus parsing.
* Adding Armada XP & 370 PCI driver, and update some clock gating
specifics.
* Introduce Marvell EBU Device Bus driver.
* Enaling USB in the armada*.dts.
* Enabling, and updating the mvebu-mbus.
* Some SATA and Ethernet related fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com> CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39564
Hauke Mehrtens [Mon, 10 Feb 2014 20:30:24 +0000 (20:30 +0000)]
kernel: fix kmod-usb-phy-nop
phy-generic.ko was renamed and moved from kernel version to version.
kernel <= 3.9: nop-usb-xceiv.ko
kernel >= 3.10 && <= 3.11: phy-nop.ko
kernel >= 3.12: phy-generic.ko
Hauke Mehrtens [Mon, 10 Feb 2014 20:12:13 +0000 (20:12 +0000)]
kernel: fix kmod-usb-net-smsc95xx
smsc95xx.ko depends on crc16.ko on kernel >= 3.8
There was an additional kmod-usb-net-smsc95xx definition in the mxs
target code which conflicted with the one in the common area.
Hauke Mehrtens [Sat, 8 Feb 2014 16:32:37 +0000 (16:32 +0000)]
kernel: XHCI PCI quirks for kernel 3.12 and 3.13
This adds empty definitions for the PCI quirks functions when they
should not be included in the kernel.
This is based on a patch by Daniel <daniel@makrotopia.org>
Hauke Mehrtens [Sat, 8 Feb 2014 15:36:03 +0000 (15:36 +0000)]
kernel: fix bridge compilation on kernel 3.13
The int brnf_call_ebtables in the header should be extern, otherwise
every object file gets its own int and they will conflict when linking
the binary.
Hauke Mehrtens [Sat, 8 Feb 2014 12:19:22 +0000 (12:19 +0000)]
mac80211: add led_trigger_blink{_oneshot}()
When led support is deactivated in the kernel and
CPTCFG_BACKPORT_BUILD_LEDS is set mac80211 references
led_trigger_blink_oneshot() but it is not declared anywhere.
This fixes the following build error:
net/mac80211/led.c: In function 'ieee80211_led_rx':
net/mac80211/led.c:25:2: error: implicit declaration of function 'led_trigger_blink_oneshot' [-Werror=implicit-function-declaration]
Jonas Gorski [Sat, 8 Feb 2014 11:47:33 +0000 (11:47 +0000)]
mvebu: remove forced module config
These should either be disabled or not present in the config, else
they might cause build issues because of unexpected unpackaged
modules, as it is the case for LEDS_CLASS.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39529
projects / thirdparty / openwrt.git / log
