Set traffic class within sl_tclass_flowlabel when create iboe AH.
Without this the TOS value will be empty when running VLAN tagged
traffic, because the TOS value is taken from the traffic class in the
address handle attributes.
Fixes: 9106c4106974 ('IB/mlx4: Fix SL to 802.1Q priority-bits mapping for IBoE') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Generally, taking an unexpected exception should be a fatal event, and
bad_mode is intended to cater for this. However, it should be possible
to contain unexpected synchronous exceptions from EL0 without bringing
the kernel down, by sending a SIGILL to the task.
We tried to apply this approach in commit 9955ac47f4ba1c95 ("arm64:
don't kill the kernel on a bad esr from el0"), by sending a signal for
any bad_mode call resulting from an EL0 exception.
However, this also applies to other unexpected exceptions, such as
SError and FIQ. The entry paths for these exceptions branch to bad_mode
without configuring the link register, and have no kernel_exit. Thus, if
we take one of these exceptions from EL0, bad_mode will eventually
return to the original user link register value.
This patch fixes this by introducing a new bad_el0_sync handler to cater
for the recoverable case, and restoring bad_mode to its original state,
whereby it calls panic() and never returns. The recoverable case
branches to bad_el0_sync with a bl, and returns to userspace via the
usual ret_to_user mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Fixes: 9955ac47f4ba1c95 ("arm64: don't kill the kernel on a bad esr from el0") Reported-by: Mark Salter <msalter@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff53 ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc9962f ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Various places assume that if nfs4_fl_prepare_ds() turns a non-NULL 'ds',
then ds->ds_clp will also be non-NULL.
This is not necessasrily true in the case when the process received a fatal signal
while nfs4_pnfs_ds_connect is waiting in nfs4_wait_ds_connect().
In that case ->ds_clp may not be set, and the devid may not recently have been marked
unavailable.
So add a test for ds_clp == NULL and return NULL in that case.
Fixes: c23266d532b4 ("NFS4.1 Fix data server connection race") Signed-off-by: NeilBrown <neilb@suse.com> Acked-by: Olga Kornievskaia <aglo@umich.edu> Acked-by: Adamson, Andy <William.Adamson@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A negative number can be specified in the cmdline which will be used as
setup_clear_cpu_cap() argument. With that we can clear/set some bit in
memory predceeding boot_cpu_data/cpu_caps_cleared which may cause kernel
to misbehave. This patch adds lower bound check to setup_disablecpuid().
Boris Petkov reproduced a crash:
[ 1.234575] BUG: unable to handle kernel paging request at ffffffff858bd540
[ 1.236535] IP: memcpy_erms+0x6/0x10
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after
resume") Fixes: 2bfd1c96a9fb ("USB: serial: ch341: remove reset_resume callback") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes CVE-2016-9191, proc_sys_readdir doesn't drop reference
added by grab_header when return from !dir_emit_dots path.
It can cause any path called unregister_sysctl_table will
wait forever.
One cgroup maintainer mentioned that "cgroup is trying to offline
a cpuset css, which takes place under cgroup_mutex. The offlining
ends up trying to drain active usages of a sysctl table which apprently
is not happening."
The real reason is that proc_sys_readdir doesn't drop reference added
by grab_header when return from !dir_emit_dots path. So this cpuset
offline path will wait here forever.
See here for details: http://www.openwall.com/lists/oss-security/2016/11/04/13
Fixes: f0c3b5093add ("[readdir] convert procfs") Reported-by: CAI Qian <caiqian@redhat.com> Tested-by: Yang Shukui <yangshukui@huawei.com> Signed-off-by: Zhou Chengming <zhouchengming1@huawei.com> Acked-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
So it must be dereferenced to be used in calculation of pci_base:
*pci_base = (dma_addr_t)*vme_base + pci_offset;
This bug was caught thanks to the following gcc warning:
drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’:
drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
*pci_base = (dma_addr_t)vme_base + pci_offset;
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a7b ("USB: ch341: set tty baud speed according to tty struct") Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Switches from emulated reads/writes to standard read/writes in fxsave,
fxrstor, sgdt, and sidt. This fixes CVE-2017-2584, a longstanding
kernel memory leak.
Since commit 283c95d0e389 ("KVM: x86: emulate FXSAVE and FXRSTOR",
2016-11-09), which is luckily not yet in any final release, this would
also be an exploitable kernel memory *write*!
Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 96051572c819194c37a8367624b285be10297eca Fixes: 283c95d0e3891b64087706b344a4b545d04a6e62 Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Steve Rutherford <srutherford@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
KVM's lapic emulation uses static_key_deferred (apic_{hw,sw}_disabled).
These are implemented with delayed_work structs which can still be
pending when the KVM module is unloaded. We've seen this cause kernel
panics when the kvm_intel module is quickly reloaded.
Use the new static_key_deferred_flush() API to flush pending updates on
module unload.
Signed-off-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Modules that use static_key_deferred need a way to synchronize with
any delayed work that is still pending when the module is unloaded.
Introduce static_key_deferred_flush() which flushes any pending
jump label updates.
[js] no STATIC_KEY_CHECK_USE in 3.12 -> remove it
Signed-off-by: David Matlack <dmatlack@google.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This is CVE-2017-2583. On Intel this causes a failed vmentry because
SS's type is neither 3 nor 7 (even though the manual says this check is
only done for usable SS, and the dmesg splat says that SS is unusable!).
On AMD it's worse: svm.c is confused and sets CPL to 0 in the vmcb.
The fix fabricates a data segment descriptor when SS is set to a null
selector, so that CPL and SS.DPL are set correctly in the VMCS/vmcb.
Furthermore, only allow setting SS to a NULL selector if SS.RPL < 3;
this in turn ensures CPL < 3 because RPL must be equal to CPL.
Thanks to Andy Lutomirski and Willy Tarreau for help in analyzing
the bug and deciphering the manuals.
return_unused_surplus_pages() decrements the global reservation count,
and frees any unused surplus pages that were backing the reservation.
Commit 7848a4bf51b3 ("mm/hugetlb.c: add cond_resched_lock() in
return_unused_surplus_pages()") added a call to cond_resched_lock in the
loop freeing the pages.
As a result, the hugetlb_lock could be dropped, and someone else could
use the pages that will be freed in subsequent iterations of the loop.
This could result in inconsistent global hugetlb page state, application
api failures (such as mmap) failures or application crashes.
When dropping the lock in return_unused_surplus_pages, make sure that
the global reservation count (resv_huge_pages) remains sufficiently
large to prevent someone else from claiming pages about to be freed.
Analyzed by Paul Cassella.
Fixes: 7848a4bf51b3 ("mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()") Link: http://lkml.kernel.org/r/1483991767-6879-1-git-send-email-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Paul Cassella <cassella@cray.com> Suggested-by: Michal Hocko <mhocko@kernel.org> Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It's because ocfs2_inode_lock() get us stale LVB in which the i_size is
not equal to the disk i_size. We mistakenly trust the LVB because the
underlaying fsdlm dlm_lock() doesn't set lkb_sbflags with
DLM_SBF_VALNOTVALID properly for us. But, why?
The current code tries to downconvert lock without DLM_LKF_VALBLK flag
to tell o2cb don't update RSB's LVB if it's a PR->NULL conversion, even
if the lock resource type needs LVB. This is not the right way for
fsdlm.
The fsdlm plugin behaves different on DLM_LKF_VALBLK, it depends on
DLM_LKF_VALBLK to decide if we care about the LVB in the LKB. If
DLM_LKF_VALBLK is not set, fsdlm will skip recovering RSB's LVB from
this lkb and set the right DLM_SBF_VALNOTVALID appropriately when node
failure happens.
The following diagram briefly illustrates how this crash happens:
RSB1 is inode metadata lock resource with LOCK_TYPE_USES_LVB;
dlm_lock(no DLM_LKF_VALBLK)
convert_lock(overwrite lkb->lkb_exflags
with no DLM_LKF_VALBLK)
RSB1: NULL RSB1: EX
reset Node2
dlm_recover_rsbs()
recover_lvb()
/* The LVB is not trustable if the node with EX fails and
* no lock >= PR is left. We should set RSB_VALNOTVALID for RSB1.
*/
if(!(kb_exflags & DLM_LKF_VALBLK)) /* This means we miss the chance to
return; * to invalid the LVB here.
*/
The 2nd round:
Node 1 Node2
RSB1(become master from recovery)
ocfs2_setattr()
ocfs2_inode_lock(NULL->EX)
/* dlm_lock() return the stale lvb without setting DLM_SBF_VALNOTVALID */
ocfs2_meta_lvb_is_trustable() return 1 /* so we don't refresh inode from disk */
ocfs2_truncate_file()
mlog_bug_on_msg(disk isize != i_size_read(inode)) /* crash! */
The fix is quite straightforward. We keep to set DLM_LKF_VALBLK flag
for dlm_lock() if the lock resource type needs LVB and the fsdlm plugin
is uesed.
Link: http://lkml.kernel.org/r/1481275846-6604-1-git-send-email-zren@suse.com Signed-off-by: Eric Ren <zren@suse.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
As a part of memory initialisation the architecture passes an array to
free_area_init_nodes() which specifies the max PFN of each memory zone.
This array is not necessarily monotonic (due to unused zones) so this
array is parsed to build monotonic lists of the min and max PFN for each
zone. ZONE_MOVABLE is special cased here as its limits are managed by
the mm subsystem rather than the architecture. Unfortunately, this
special casing is broken when ZONE_MOVABLE is the not the last zone in
the zone list. The core of the issue is:
if (i == ZONE_MOVABLE)
continue;
arch_zone_lowest_possible_pfn[i] =
arch_zone_highest_possible_pfn[i-1];
As ZONE_MOVABLE is skipped the lowest_possible_pfn of the next zone will
be set to zero. This patch fixes this bug by adding explicitly tracking
where the next zone should start rather than relying on the contents
arch_zone_highest_possible_pfn[].
Thie is low priority. To get bitten by this you need to enable a zone
that appears after ZONE_MOVABLE in the zone_type enum. As far as I can
tell this means running a kernel with ZONE_DEVICE or ZONE_CMA enabled,
so I can't see this affecting too many people.
I only noticed this because I've been fiddling with ZONE_DEVICE on
powerpc and 4.6 broke my test kernel. This bug, in conjunction with the
changes in Taku Izumi's kernelcore=mirror patch (d91749c1dda71) and
powerpc being the odd architecture which initialises max_zone_pfn[] to
~0ul instead of 0 caused all of system memory to be placed into
ZONE_DEVICE at boot, followed a panic since device memory cannot be used
for kernel allocations. I've already submitted a patch to fix the
powerpc specific bits, but I figured this should be fixed too.
Link: http://lkml.kernel.org/r/1462435033-15601-1-git-send-email-oohall@gmail.com Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Cc: Anton Blanchard <anton@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14be ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865f4 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865f4 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The GRO fast path caches the frag0 address. This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.
This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.
This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.
Fixes: 78a478d0efd9 ("gro: Inline skb_gro_header and cache frag0 virtual address") Reported-by: Slava Shwartsman <slavash@mellanox.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On 32bit arches, (skb->end - skb->data) is not 'unsigned int',
so we shall use min_t() instead of min() to avoid a compiler error.
Fixes: 1272ce87fa01 ("gro: Enter slow-path if there is no tailroom") Reported-by: kernel test robot <fengguang.wu@intel.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The GRO path has a fast-path where we avoid calling pskb_may_pull
and pskb_expand by directly accessing frag0. However, this should
only be done if we have enough tailroom in the skb as otherwise
we'll have to expand it later anyway.
This patch adds the check by capping frag0_len with the skb tailroom.
Fixes: cb18978cbf45 ("gro: Open-code final pskb_may_pull") Reported-by: Slava Shwartsman <slavash@mellanox.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes: 4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove") Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes: 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup") Reported-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Tested-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b95 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a disfunctional timer, e.g. dummy timer, is installed, the tick core
tries to setup the broadcast timer.
If no broadcast device is installed, the kernel crashes with a NULL pointer
dereference in tick_broadcast_setup_oneshot() because the function has no
sanity check.
Reported-by: Mason <slash.tmp@free.fr> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Richard Cochran <rcochran@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org>, Cc: Sebastian Frias <sf84@laposte.net> Cc: Thibaud Cornic <thibaud_cornic@sigmadesigns.com> Cc: Robin Murphy <robin.murphy@arm.com> Link: http://lkml.kernel.org/r/1147ef90-7877-e4d2-bb2b-5c4fa8d3144b@free.fr Signed-off-by: Jiri Slaby <jslaby@suse.cz>
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The current_user_ns() macro currently returns &init_user_ns when user
namespaces are disabled, and that causes several warnings when building
with gcc-6.0 in code that compares the result of the macro to
&init_user_ns itself:
fs/xfs/xfs_ioctl.c: In function 'xfs_ioctl_setattr_check_projid':
fs/xfs/xfs_ioctl.c:1249:22: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (current_user_ns() == &init_user_ns)
This is a legitimate warning in principle, but here it isn't really
helpful, so I'm reprasing the definition in a way that shuts up the
warning. Apparently gcc only warns when comparing identical literals,
but it can figure out that the result of an inline function can be
identical to a constant expression in order to optimize a condition yet
not warn about the fact that the condition is known at compile time.
This is exactly what we want here, and it looks reasonable because we
generally prefer inline functions over macros anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: David Howells <dhowells@redhat.com> Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com> Cc: James Morris <james.l.morris@oracle.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b66 ("[SCSI] mvsas: Add new macros and functions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.
When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.
So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.
So left check value should be left <= 0x20 (two commands).
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188561. Function
wm831x_clkout_is_prepared() returns "true" when it fails to read
CLOCK_CONTROL_1. "true" means the device is already prepared. So
return "true" on the read failure seems improper.
Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Fixes: f05259a6ffa4 ("clk: wm831x: Add initial WM831x clock driver") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix overflows seen when writing into fan speed limit attributes.
Also fix crash due to division by zero, seen when certain very
large values (such as 2147483648, or 0x80000000) are written
into fan speed limit attributes.
Fixes: 594fbe713bf60 ("Add support for GMT G762/G763 PWM fan controllers") Cc: Arnaud Ebalard <arno@natisbad.org> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If CONFIG_ETRAX_AXISFLASHMAP is not configured, the flash rescue image
object file is empty. With recent versions of binutils, this results
in the following build error.
cris-linux-objcopy: error:
the input file 'arch/cris/boot/rescue/rescue.o' has no sections
This is seen, for example, when trying to build cris:allnoconfig
with recently generated toolchains.
Since it does not make sense to build a flash rescue image if there is
no flash, only build it if CONFIG_ETRAX_AXISFLASHMAP is enabled.
commit 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com> Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The oversampling ratio is controlled using the oversampling pins,
OS [2:0] with OS2 being the MSB control bit, and OS0 the LSB control
bit.
The gpio connected to the OS2 pin is not being set correctly, only OS0
and OS1 pins are being set. Fix the typo to allow proper control of the
oversampling pins.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com> Fixes: b9618c0 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4") Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure to drop the references taken by of_parse_phandle() and
bus_find_device() before returning from am335x_get_phy_control().
Note that there is no guarantee that the devres-managed struct
phy_control will be valid for the lifetime of the sibling phy device
regardless of this change.
Fixes: 3bb869c8b3f1 ("usb: phy: Add AM335x PHY driver") Acked-by: Bin Liu <b-liu@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The function returns -EINVAL even if it builds the stream properly.
The bogus error code sneaked in during the code refactoring, but it
wasn't noticed until now since the returned error code itself is
ignored in anyway. Kill it here, but there is no behavior change by
this patch, obviously.
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d78 ("USB: serial: add support for serial port on the moschip 7715") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:
Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In case a device is left in "boot-mode" we must not register any port
devices in order to avoid a NULL-pointer dereference on open due to
missing endpoints. This could be used by a malicious device to trigger
an OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial])
[<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Check for the expected endpoints in attach() and fail loudly if not
present.
Note that failing to do this appears to be benign since da280e348866
("USB: keyspan_pda: clean up write-urb busy handling") which prevents a
NULL-pointer dereference in write() by never marking a non-existent
write-urb as free.
The write URB was being killed using the synchronous interface while
holding a spin lock in close().
Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
By convention (according to doc) if function does not provide
get_alt() callback composite framework should assume that it has only
altsetting 0 and should respond with error if host tries to set
other one.
After commit dd4dff8b035f ("USB: composite: Fix bug: should test
set_alt function pointer before use it")
we started checking set_alt() callback instead of get_alt().
This check is useless as we check if set_alt() is set inside
usb_add_function() and fail if it's NULL.
Let's fix this check and move comment about why we check the get
method instead of set a little bit closer to prevent future false
fixes.
Fixes: dd4dff8b035f ("USB: composite: Fix bug: should test set_alt function pointer before use it") Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The stop_activity() routine in dummy-hcd is supposed to unlink all
active requests for every endpoint, among other things. But it
doesn't handle ep0. As a result, fuzz testing can generate a WARNING
like the following:
This patch fixes the problem by iterating over all the endpoints in
the driver's ep array instead of iterating over the gadget's ep_list,
which explicitly leaves out ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user. In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).
This patch adds the additional check and fixes the existing check. It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The cause of the bug is subtle. The dev_config() routine gets called
twice by the fuzzer. The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set. But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.
The second time dev_config() is called, the user data contains only a
full-speed config descriptor. But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config. Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.
The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Indeed, there is a comment saying that the value of len is restricted
to a 16-bit integer, but the code doesn't actually do this.
This patch fixes the warning. It replaces the comment with a
computation that forces the amount of data copied from the user in
ep0_write() to be no larger than the wLength size for the control
transfer, which is a 16-bit quantity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Andrey Konovalov reported that we were not properly checking the upper
limit before of a device configuration size before calling
memdup_user(), which could cause some problems.
So set the upper limit to PAGE_SIZE * 4, which should be good enough for
all devices.
Similarly to the aemif clock - this screws up the linked list of clock
children. Create a separate clock for mdio inheriting the rate from
emac_clk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a comment over mdio_clk to explaing its existence +
commit headline updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Although the old quirk table showed ASUS X71SL with ALC663 codec being
compatible with asus-mode3 fixup, the bugzilla reporter explained that
asus-model8 fits better for the dual headphone controls. So be it.
ASUS ROG Ranger VIII with ALC1150 codec requires the extra GPIO pin to
up for the front panel. Just use the existing fixup for setting up
the GPIO pins.
projects / thirdparty / kernel / stable.git / log
