Chris Chiu [Wed, 15 Dec 2021 08:58:19 +0000 (16:58 +0800)]
rtl8xxxu: Improve the A-MPDU retransmission rate with RTS/CTS protection
The A-MPDU TX retransmission rate is always high (> 20%) even in a very
clean environment. However, the vendor driver retransimission rate is
< 10% in the same test bed. The difference is the vendor driver starts
the A-MPDU TXOP with initial RTS/CTS handshake which is observed in the
air capture and the TX descriptor. Since the driver does not know how
many frames will be aggregated and the estimated duration, forcing the
RTS/CTS protection for A-MPDU helps to lower the retransmission rate
from > 20% to ~12% in the same test setup with the vendor driver.
Chin-Yen Lee [Fri, 17 Dec 2021 01:24:21 +0000 (09:24 +0800)]
rtw88: don't check CRC of VHT-SIG-B in 802.11ac signal
Currently all realtek wifi chip is set to check CRC of VHT-SIG-B
in 802.11ac signal, but some AP don't calculate the CRC and packets
from these AP can't be received and lead to disconnection.
We disable the check defaultly to avoid this case.
Kai-Heng Feng [Wed, 15 Dec 2021 11:46:34 +0000 (19:46 +0800)]
rtw88: Disable PCIe ASPM while doing NAPI poll on 8821CE
Many Intel based platforms face system random freeze after commit 9e2fd29864c5 ("rtw88: add napi support").
The commit itself shouldn't be the culprit. My guess is that the 8821CE
only leaves ASPM L1 for a short period when IRQ is raised. Since IRQ is
masked during NAPI polling, the PCIe link stays at L1 and makes RX DMA
extremely slow. Eventually the RX ring becomes messed up:
[ 1133.194697] rtw_8821ce 0000:02:00.0: pci bus timeout, check dma status
Since the 8821CE hardware may fail to leave ASPM L1, manually do it in
the driver to resolve the issue.
Dan Carpenter [Fri, 17 Dec 2021 15:03:12 +0000 (18:03 +0300)]
wilc1000: fix double free error in probe()
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3bcd ("wilc1000: use goto labels on error path") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
Deren Wu [Thu, 16 Dec 2021 17:02:09 +0000 (01:02 +0800)]
mt76: mt7921s: fix cmd timeout in throughput test
During heavy loading throughtput test, the RX buffer (128)
would be exhausted and some RX pkts dropped randomly. Increase
buffer size from 128 to 512 (a safer length) to avoid tput degrade
or cmd-timeout problem.
Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Wed, 15 Dec 2021 21:25:37 +0000 (05:25 +0800)]
mt76: mt7921s: fix suspend error with enlarging mcu timeout value
Fix the false positive suspend error that may occur on mt7921s
with enlarging mcu timeout value.
The reason why we have to enlarge mcu timeout from HZ / 3 to HZ is
we should consider the additional overhead caused by running
concurrently with btmtksdio (a MT7921 bluetooth SDIO driver) that
would compete for the same SDIO bus in process context to complete
the suspend procedure.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Wed, 15 Dec 2021 21:25:35 +0000 (05:25 +0800)]
mt76: mt7921: fix possible resume failure
Fix the possible resume failure due to mt76_connac_mcu_set_hif_suspend
timeout.
That is because clearing the flag pm->suspended too early opened up a race
window, where mt7921_poll_tx/rx scheduled a ps_work to put the device in
doze mode, that is unexpected for the device is being resumed from the
suspend state and would make the remaining MCU comamnds in resume handler
failed to execute.
Fixes: ffa1bf97425b ("mt76: mt7921: introduce PM support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Tue, 30 Nov 2021 09:36:15 +0000 (10:36 +0100)]
mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
last_ch configuration must not be dependent on the current configured band
but it is defined by hw capabilities since the fw always expects the
following order:
- 2GHz
- 5GHz
- 6GHz
Fixes: 9b2ea8eee42a1 ("mt76: connac: set 6G phymode in single-sku support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Mon, 29 Nov 2021 23:05:28 +0000 (07:05 +0800)]
mt76: mt7921s: fix possible kernel crash due to invalid Rx count
Return the proper error code when out-of-range the Rx aggregation count
are reported from the hardware that would create the unreasonable extreme
large Rx buffer.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deren Wu [Sun, 28 Nov 2021 07:43:59 +0000 (15:43 +0800)]
mt76: mt7921s: fix bus hang with wrong privilege
Accroding to chip hw flow, mt7921s need to re-acquire privilege
again before normal running. Otherwise, the bus may be stuck in
an abnormal status.
Tested-by: Leon Yen <Leon.Yen@mediatek.com> Co-developed-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com> Signed-off-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com> Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 25 Nov 2021 12:42:32 +0000 (13:42 +0100)]
mt76: clear sta powersave flag after notifying driver
If the driver has configured the hardware to drop packets for a sta that was
in powersave mode, then clearing the flag too early opens up a small race
window during which packets could be dropped on wakeup
Felix Fietkau [Thu, 25 Nov 2021 09:47:14 +0000 (10:47 +0100)]
mt76: mt7915: improve wmm index allocation
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
Felix Fietkau [Thu, 25 Nov 2021 09:42:12 +0000 (10:42 +0100)]
mt76: mt7615: improve wmm index allocation
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.
Sean Wang [Fri, 19 Nov 2021 23:22:11 +0000 (07:22 +0800)]
mt76: mt7921s: fix the device cannot sleep deeply in suspend
According to the MT7921S firmware, the cmd MCU_UNI_CMD_HIF_CTRL have to
be last MCU command to execute in suspend handler and all data traffic
have to be stopped before the cmd MCU_UNI_CMD_HIF_CTRL starts as well
in order that mt7921 can successfully fall into the deep sleep mode.
Where we reuse the flag MT76_STATE_SUSPEND and avoid creating
another global flag to stop all of the traffic onto the SDIO bus.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support") Reported-by: Leon Yen <leon.yen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Fri, 19 Nov 2021 23:22:10 +0000 (07:22 +0800)]
mt76: mt7921: move mt76_connac_mcu_set_hif_suspend to bus-related files
This is a preliminary patch for the following patch
("mt76: mt7921s: fix the device cannot sleep deeply in suspend).
mt76_connac_mcu_set_hif_suspend eventually would be handled in each
bus-level suspend/resume handler in either mt7921/sdio.c or mt7921/pci.c
depending on what type of the bus the device is running on. We can move
mt76_connac_mcu_set_hif_suspend to bus-related files to simplify the logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 23 Nov 2021 10:49:04 +0000 (11:49 +0100)]
mt76: mt7615: fix decap offload corner case with 4-addr VLAN frames
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Felix Fietkau [Tue, 23 Nov 2021 10:37:47 +0000 (11:37 +0100)]
mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Xing Song [Fri, 19 Nov 2021 06:37:06 +0000 (14:37 +0800)]
mt76: do not pass the received frame with decryption error
MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <xing.song@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Thu, 18 Nov 2021 15:21:43 +0000 (16:21 +0100)]
mt76: connac: remove PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
Get rid of PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
routine since mode is an u8 and PHY_MODE_AX_6G is set in phymode_ext
field in mt76_connac_bss_basic_tlv.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Thu, 18 Nov 2021 12:49:41 +0000 (13:49 +0100)]
mt76: connac: fix a theoretical NULL pointer dereference in mt76_connac_get_phy_mode
Even if it is not a real bug since mt76_connac_get_phy_mode runs just
for mt7921 where only STA is supported, fix a theoretical NULL pointer
dereference if new added modes do not support HE
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Thu, 18 Nov 2021 10:50:27 +0000 (11:50 +0100)]
mt76: mt7921: fix possible NULL pointer dereference in mt7921_mac_write_txwi
Fix a possible NULL pointer deference issue in mt7921_mac_write_txwi
routine if vif is NULL.
Fixes: 33920b2bf0483 ("mt76: add support for setting mcast rate") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Thu, 18 Nov 2021 10:42:06 +0000 (11:42 +0100)]
mt76: fix possible OOB issue in mt76_calculate_default_rate
Cap max offset value to ARRAY_SIZE(mt76_rates) - 1 in
mt76_calculate_default_rate routine in order to avoid possible Out Of
Bound accesses.
Fixes: 33920b2bf0483 ("mt76: add support for setting mcast rate") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
David S. Miller [Sat, 18 Dec 2021 12:22:17 +0000 (12:22 +0000)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-12-17
Brett Creeley says:
This patch series adds support in the iavf driver for communicating and
using VIRTCHNL_VF_OFFLOAD_VLAN_V2. The current VIRTCHNL_VF_OFFLOAD_VLAN
is very limited and covers all 802.1Q VLAN offloads and filtering with
no granularity.
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 adds more granularity, flexibility,
and support for 802.1ad offloads and filtering. This includes the VF
negotiating which VLAN offloads/filtering it's allowed, where VLAN tags
should be inserted and/or stripped into and from descriptors, and the
supported VLAN protocols.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shayne Chen [Sun, 14 Nov 2021 14:59:09 +0000 (22:59 +0800)]
mt76: testmode: add support to set MAC
Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Shayne Chen [Sun, 31 Oct 2021 17:48:42 +0000 (01:48 +0800)]
mt76: mt7915: add default calibrated data support
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Xing Song [Wed, 10 Nov 2021 04:19:31 +0000 (12:19 +0800)]
mt76: reverse the first fragmented frame to 802.11
The HW can apply header translation to first fragmented frame, and
ramaining fragmented frame can only keep 802.11 format. Check and
reverse the first fragmented frame to 802.11 format to make sure
them can be defragmented by mac80211.
Signed-off-by: Xing Song <xing.song@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Wed, 3 Nov 2021 00:05:16 +0000 (08:05 +0800)]
mt76: mt7921: fix MT7921E reset failure
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1eb ("mt76: mt7921: refactor mcu.c to be bus independent") Reported-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Peter Chiu [Mon, 1 Nov 2021 02:01:13 +0000 (10:01 +0800)]
mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7615_register_ext_phy() outside the init_work().
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Thu, 28 Oct 2021 22:29:58 +0000 (06:29 +0800)]
mt76: mt7921: drop offload_flags overwritten
offload_flags have to be dropped for mt7921 because mt76.omac_idx 0 would
always run as station mode that would cause Tx encapsulation setting
is not applied to mac80211.
Also, drop IEEE80211_OFFLOAD_ENCAP_4ADDR too because it is not really
being supported.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sat, 23 Oct 2021 13:49:38 +0000 (15:49 +0200)]
mt76: mt7915: get rid of mt7915_mcu_set_fixed_rate routine
Fix the following sparse warning removing mt7915_mcu_set_fixed_rate
since it is no longer used:
warning: symbol 'mt7915_mcu_set_fixed_rate' was not declared.
Should it be static?
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
====================
mptcp: Miscellaneous changes for 5.17
These are three unrelated patches that we've been testing in the MPTCP
tree.
Patch 1 modifies the packet scheduler that picks which TCP subflow is
used for each chunk of outgoing data. The updated scheduler improves
throughput on multiple-subflow connections.
Patch 2 updates a selftest to verify recent TCP_ULP sockopt changes
on MPTCP fallback sockets.
Patch 3 cleans up some unnecessary comparisons with an 8-bit value.
====================
Florian Westphal [Fri, 17 Dec 2021 23:37:01 +0000 (15:37 -0800)]
selftests: mptcp: try to set mptcp ulp mode in different sk states
The kernel will crash without
'mptcp: clear 'kern' flag from fallback sockets' change.
Since this doesn't slow down testing in a noticeable way,
run this unconditionally.
The explicit test did not catch this, because the check was done
for tcp socket returned by 'socket(.. IPPROTO_TCP) rather than a
tcp socket returned by accept() on a mptcp listen fd.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 17 Dec 2021 23:37:00 +0000 (15:37 -0800)]
mptcp: enforce HoL-blocking estimation
The MPTCP packet scheduler has sub-optimal behavior with asymmetric
subflows: if the faster subflow-level cwin is closed, the packet
scheduler can enqueue "too much" data on a slower subflow.
When all the data on the faster subflow is acked, if the mptcp-level
cwin is closed, and link utilization becomes suboptimal.
The solution is implementing blest-like[1] HoL-blocking estimation,
transmitting only on the subflow with the shorter estimated time to
flush the queued memory. If such subflows cwin is closed, we wait
even if other subflows are available.
This is quite simpler than the original blest implementation, as we
leverage the pacing rate provided by the TCP socket. To get a more
accurate estimation for the subflow linger-time, we maintain a
per-subflow weighted average of such info.
Additionally drop magic numbers usage in favor of newly defined
macros and use more meaningful names for status variable.
Dan Carpenter [Fri, 17 Dec 2021 07:10:37 +0000 (10:10 +0300)]
net: ethernet: mtk_eth_soc: delete some dead code
The debugfs_create_dir() function never returns NULL. It does return
error pointers but in normal situations like this there is no need to
check for errors.
Gerhard Engleder [Thu, 16 Dec 2021 20:01:54 +0000 (21:01 +0100)]
tsnep: Fix s390 devm_ioremap_resource warning
The following warning is fixed with additional config dependencies:
s390-linux-ld: drivers/net/ethernet/engleder/tsnep_main.o: in function `tsnep_probe':
tsnep_main.c:(.text+0x1de6): undefined reference to `devm_ioremap_resource'
Brett Creeley [Tue, 30 Nov 2021 00:16:04 +0000 (16:16 -0800)]
iavf: Restrict maximum VLAN filters for VIRTCHNL_VF_OFFLOAD_VLAN_V2
For VIRTCHNL_VF_OFFLOAD_VLAN, PF's would limit the number of VLAN
filters a VF was allowed to add. However, by the time the opcode failed,
the VLAN netdev had already been added. VIRTCHNL_VF_OFFLOAD_VLAN_V2
added the ability for a PF to tell the VF how many VLAN filters it's
allowed to add. Make changes to support that functionality.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:03 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 offload enable/disable
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if
successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
Multiple changes were needed to support this new functionality.
1. Added new aq_required flags to support any kind of VLAN stripping and
insertion offload requests via virtchnl.
2. Added the new method iavf_set_vlan_offload_features() that's
used during VF initialization, VF reset, and iavf_set_features() to
set the aq_required bits based on the current VLAN offload
configuration of the VF's netdev.
3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2,
VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2,
and VIRTCHNL_OP_ENABLE_INSERTION_V2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:02 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 hotpath
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the PF to set the location of the Tx and Rx VLAN tag for insertion and
stripping offloads. In order to support this functionality a few changes
are needed.
1. Add a new method to cache the VLAN tag location based on negotiated
capabilities for the Tx and Rx ring flags. This needs to be called in
the initialization and reset paths.
2. Refactor the transmit hotpath to account for the new Tx ring flags.
When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to
insert the VLAN tag in the L2TAG2 field of the transmit descriptor.
When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs
to use the l2tag1 field of the data descriptor (same behavior as
before).
3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify
transmit hardware VLAN offload functionality by only depending on the
skb_vlan_tag_present() function. This can be done because the OS
won't request transmit offload for a VLAN unless the driver told the
OS it's supported and enabled.
4. Refactor the receive hotpath to account for the new Rx ring flags and
VLAN ethertypes. This requires checking the Rx ring flags and
descriptor status bits to determine the location of the VLAN tag.
Also, since only a single ethertype can be supported at a time, check
the enabled netdev features before specifying a VLAN ethertype in
__vlan_hwaccel_put_tag().
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:01 +0000 (16:16 -0800)]
iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config
Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN
capabilities (i.e. 802.1AD offloads and filtering). In order to
communicate these capabilities to the netdev layer, the VF needs to
parse its VLAN capabilities based on whether it was able to negotiation
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of
these.
In order to support this, add the following functionality:
iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN
features that the underlying hardware supports and that can be toggled
off/on based on the negotiated capabiltiies. For example, if
VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked
with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If
VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or
stripping can be toggled on/off.
iavf_get_netdev_vlan_features() - This is used to determine the VLAN
features that the underlying hardware supports and that should be
enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was
negotiated, then any supported capability that has its ethertype_init
filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was
negotiated, then filtering, stripping, and insertion should be enabled
by default.
Also, refactor iavf_fix_features() to take into account the new
capabilities. To do this, query all the supported features (enabled by
default and toggleable) and make sure the requested change is supported.
If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no
need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told
the netdev layer which features can be toggled via netdev->hw_features
during iavf_process_config(), so only those features will be requested
to change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:00 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation
In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the
VF driver needs to rework it's initialization state machine and reset
flow. This has to be done because successful negotiation of
VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second
capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before
configuring the adapter and its netdev.
Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the
VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either
support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or
neither. Both of these offloads should never be supported together.
Based on this, add 2 new states to the initialization state machine:
The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store
the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2
was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state.
The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the
adapter/netdev after the resource requests have finished. The VF will
move into this state regardless of whether it successfully negotiated
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2.
Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set
it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully
negotiated then the VF will request its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed
because the PF may change/modify the VF's configuration during VF reset
(i.e. modifying the VF's port VLAN configuration).
This also, required the VF to call netdev_update_features() since its
VLAN features may change during VF reset. Make sure to call this under
rtnl_lock().
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:15:59 +0000 (16:15 -0800)]
virtchnl: Add support for new VLAN capabilities
Currently VIRTCHNL only allows for VLAN filtering and offloads to happen
on a single 802.1Q VLAN. Add support to filter and offload on inner,
outer, and/or inner + outer VLANs.
This is done by introducing the new capability
VIRTCHNL_VF_OFFLOAD_VLAN_V2. The flow to negotiate this new capability
is shown below.
1. VF - sets the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit in the
virtchnl_vf_resource.vf_caps_flags during the
VIRTCHNL_OP_GET_VF_RESOURCES request message. The VF should also set
the VIRTCHNL_VF_OFFLOAD_VLAN bit in case the PF driver doesn't support
the new capability.
2. PF - sets the VLAN capability bit it supports in the
VIRTCHNL_OP_GET_VF_RESOURCES response message. This will either be
VIRTCHNL_VF_OFFLOAD_VLAN_V2, VIRTCHNL_VF_OFFLOAD_VLAN, or none.
3. VF - If the VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability was ACK'd by the
PF, then the VF needs to request the VLAN capabilities of the
PF/Device by issuing a VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS request.
If the VIRTCHNL_VF_OFFLOAD_VLAN capability was ACK'd then the VF
knows only single 802.1Q VLAN filtering/offloads are supported. If no
VLAN capability is ACK'd then the PF/Device doesn't support hardware
VLAN filtering/offloads for this VF.
4. PF - Populates the virtchnl_vlan_caps structure based on what it
allows/supports for that VF and sends that response via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
After VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is successfully negotiated
the VF driver needs to interpret the capabilities supported by the
underlying PF/Device. The VF will be allowed to filter/offload the
inner 802.1Q, outer (various ethertype), inner 802.1Q + outer
(various ethertypes), or none based on which fields are set.
The VF will also need to interpret where the VLAN tag should be inserted
and/or stripped based on the negotiated capabilities.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jakub Kicinski [Fri, 17 Dec 2021 15:30:06 +0000 (07:30 -0800)]
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Changcheng Deng [Thu, 16 Dec 2021 09:13:39 +0000 (09:13 +0000)]
net: dsa: microchip: remove unneeded variable
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Dexuan Cui [Thu, 16 Dec 2021 00:17:48 +0000 (16:17 -0800)]
net: mana: Add RX fencing
RX fencing allows the driver to know that any prior change to the RQs has
finished, e.g. when the RQs are disabled/enabled or the hashkey/indirection
table are changed, RX fencing is required.
Remove the previous workaround "ssleep(1)" and add the real support for
RX fencing as the PF driver supports the MANA_FENCE_RQ request now (any
old PF driver not supporting the request won't be used in production).
Yinjun Zhang [Thu, 16 Dec 2021 01:37:01 +0000 (20:37 -0500)]
nfp: flower: refine the use of circular buffer
The current use of circular buffer to manage stats_context_id is
very obscure, and it will cause problem if its element size is
not power of two. So change the use more straightforward and
scalable, and also change that for mask_id to keep consistency.
Linus Torvalds [Thu, 16 Dec 2021 23:02:14 +0000 (15:02 -0800)]
Merge tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from mac80211, wifi, bpf.
Relatively large batches of fixes from BPF and the WiFi stack, calm in
general networking.
Current release - regressions:
- dpaa2-eth: fix buffer overrun when reporting ethtool statistics
Current release - new code bugs:
- bpf: fix incorrect state pruning for <8B spill/fill
- iavf:
- add missing unlocks in iavf_watchdog_task()
- do not override the adapter state in the watchdog task (again)
- mlxsw: spectrum_router: consolidate MAC profiles when possible
Previous releases - regressions:
- mac80211 fixes:
- rate control, avoid driver crash for retransmitted frames
- regression in SSN handling of addba tx
- a memory leak where sta_info is not freed
- marking TX-during-stop for TX in in_reconfig, prevent stall
- cfg80211: acquire wiphy mutex on regulatory work
- wifi drivers: fix build regressions and LED config dependency
- virtio_net: fix rx_drops stat for small pkts
- dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()
Previous releases - always broken:
- bpf fixes:
- kernel address leakage in atomic fetch
- kernel address leakage in atomic cmpxchg's r0 aux reg
- signed bounds propagation after mov32
- extable fixup offset
- extable address check
- mac80211:
- fix the size used for building probe request
- send ADDBA requests using the tid/queue of the aggregation
session
- agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid
deadlocks
- validate extended element ID is present
- mptcp:
- never allow the PM to close a listener subflow (null-defer)
- clear 'kern' flag from fallback sockets, prevent crash
- fix deadlock in __mptcp_push_pending()
- inet_diag: fix kernel-infoleak for UDP sockets
- xsk: do not sleep in poll() when need_wakeup set
- smc: avoid very long waits in smc_release()
- sch_ets: don't remove idle classes from the round-robin list
- netdevsim:
- zero-initialize memory for bpf map's value, prevent info leak
- don't let user space overwrite read only (max) ethtool parms
- ixgbe: set X550 MDIO speed before talking to PHY
- stmmac:
- fix null-deref in flower deletion w/ VLAN prio Rx steering
- dwmac-rk: fix oob read in rk_gmac_setup
- ice: time stamping fixes
- systemport: add global locking for descriptor life cycle"
* tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits)
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
sit: do not call ipip6_dev_free() from sit_init_net()
net: systemport: Add global locking for descriptor lifecycle
net/smc: Prevent smc_release() from long blocking
net: Fix double 0x prefix print in SKB dump
virtio_net: fix rx_drops stat for small pkts
dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
sfc_ef100: potential dereference of null pointer
net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
net: usb: lan78xx: add Allied Telesis AT29M2-AF
net/packet: rx_owner_map depends on pg_vec
netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
dpaa2-eth: fix ethtool statistics
ixgbe: set X550 MDIO speed before talking to PHY
...
Linus Torvalds [Thu, 16 Dec 2021 22:48:57 +0000 (14:48 -0800)]
Merge tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of DT fixes, mostly for mistakes found through
static checking of the dts files again, as well as a couple of minor
changes to address incorrect DT settings.
For i.MX, there is yet another series of devitree changes to update
RGMII delay settings for ethernet, which is an ongoing problem after
some driver changes.
For SoC specific device drivers, a number of smaller fixes came up:
- i.MX SoC identification was incorrectly registered non-i.MX
machines when the driver is built-in
- One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work
properly
- a few compile fixes for warnings that get in the way of -Werror
- a string overflow in the scpi firmware driver
- a boot failure with FORTIFY_SOURCE on Rockchips machines
- broken error handling in the AMD TEE driver
- a revert for a tegra reset driver commit that broke HDA"
* tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
soc/tegra: fuse: Fix bitwise vs. logical OR warning
firmware: arm_scpi: Fix string overflow in SCPI genpd driver
soc: imx: Register SoC device only on i.MX boards
soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset
ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
arm64: dts: imx8mq: remove interconnect property from lcdif
ARM: socfpga: dts: fix qspi node compatible
arm64: dts: apple: add #interrupt-cells property to pinctrl nodes
dt-bindings: i2c: apple,i2c: allow multiple compatibles
arm64: meson: remove COMMON_CLK
arm64: meson: fix dts for JetHub D1
tee: amdtee: fix an IS_ERR() vs NULL bug
arm64: dts: apple: change ethernet0 device type to ethernet
arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
arm64: dts: rockchip: fix poweroff on helios64
arm64: dts: rockchip: fix audio-supply for Rock Pi 4
arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge
ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up
...
We've added 15 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 434 insertions(+), 30 deletions(-).
The main changes are:
1) Fix incorrect verifier state pruning behavior for <8B register spill/fill,
from Paul Chaignon.
2) Fix x86-64 JIT's extable handling for fentry/fexit when return pointer
is an ERR_PTR(), from Alexei Starovoitov.
3) Fix 3 different possibilities that BPF verifier missed where unprivileged
could leak kernel addresses, from Daniel Borkmann.
4) Fix xsk's poll behavior under need_wakeup flag, from Magnus Karlsson.
5) Fix an oob-write in test_verifier due to a missed MAX_NR_MAPS bump,
from Kumar Kartikeya Dwivedi.
6) Fix a race in test_btf_skc_cls_ingress selftest, from Martin KaFai Lau.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer
bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg
bpf, selftests: Add test case for atomic fetch on spilled pointer
bpf: Fix kernel address leakage in atomic fetch
selftests/bpf: Fix OOB write in test_verifier
xsk: Do not sleep in poll() when need_wakeup set
selftests/bpf: Tests for state pruning with u32 spill/fill
bpf: Fix incorrect state pruning for <8B spill/fill
====================
projects / thirdparty / linux.git / log
