Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:
kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout
According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:
'When an interrupt transfer involves more data than can fit in one
data payload of the currently established maximum size, all data
payloads are required to be maximum-sized except for the last data
payload, which will contain the remaining data. An interrupt transfer
is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data expected
• Transfers a packet with a payload size less than wMaxPacketSize or
transfers a zero-length packet'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365 Fixes: 7b05933340f4 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bt_init() fails, the debugfs directory currently is not removed. If
the module is loaded again after that, the debugfs directory is not set
up properly due to the existing directory.
# modprobe bluetooth
# ls -laF /sys/kernel/debug/bluetooth
total 0
drwxr-xr-x 2 root root 0 Sep 27 14:26 ./
drwx------ 31 root root 0 Sep 27 14:25 ../
-r--r--r-- 1 root root 0 Sep 27 14:26 l2cap
-r--r--r-- 1 root root 0 Sep 27 14:26 sco
# modprobe -r bluetooth
# ls -laF /sys/kernel/debug/bluetooth
ls: cannot access '/sys/kernel/debug/bluetooth': No such file or directory
#
# modprobe bluetooth
modprobe: ERROR: could not insert 'bluetooth': Invalid argument
# dmesg | tail -n 6
Bluetooth: Core ver 2.22
NET: Registered PF_BLUETOOTH protocol family
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Faking l2cap_init() failure for testing
NET: Unregistered PF_BLUETOOTH protocol family
# ls -laF /sys/kernel/debug/bluetooth
total 0
drwxr-xr-x 2 root root 0 Sep 27 14:31 ./
drwx------ 31 root root 0 Sep 27 14:26 ../
#
The opt3001 driver uses predetermined full-scale range values to
determine what exponent to use for event trigger threshold values.
The problem is that one of the values specified in the datasheet is
missing from the implementation. This causes larger values to be
scaled down to an incorrect exponent, effectively reducing the
maximum settable threshold value by a factor of 2.
Add missing full-scale range array value.
Fixes: 94a9b7b1809f ("iio: light: add support for TI's opt3001 light sensor") Signed-off-by: Emil Gedenryd <emil.gedenryd@axis.com> Cc: <Stable@vger.kernel.org> Link: https://patch.msgid.link/20240913-add_opt3002-v2-1-69e04f840360@axis.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev pointer that is received as an argument in the
in_illuminance_period_available_show function references the device
embedded in the IIO device, not in the i2c client.
dev_to_iio_dev() must be used to accessthe right data. The current
implementation leads to a segmentation fault on every attempt to read
the attribute because indio_dev gets a NULL assignment.
This bug has been present since the first appearance of the driver,
apparently since the last version (V6) before getting applied. A
constant attribute was used until then, and the last modifications might
have not been tested again.
Cc: stable@vger.kernel.org Fixes: 7b779f573c48 ("iio: light: add driver for veml6030 ambient light sensor") Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20240913-veml6035-v1-3-0b09c0c90418@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver still uses the sensor resolution provided in the datasheet
until Rev. 1.6, 28-Apr-2022, which was updated with Rev 1.7,
28-Nov-2023. The original ambient light resolution has been updated from
0.0036 lx/ct to 0.0042 lx/ct, which is the value that can be found in
the current device datasheet.
Update the default resolution for IT = 100 ms and GAIN = 1/8 from the
original 4608 mlux/cnt to the current value from the "Resolution and
maximum detection range" table (Application Note 84367, page 5), 5376
mlux/cnt.
Cc: <stable@vger.kernel.org> Fixes: 7b779f573c48 ("iio: light: add driver for veml6030 ambient light sensor") Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20240923-veml6035-v2-1-58c72a0df31c@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if condition (!bo and !vmw_kms_srf_ok()) was met
we go to err_out with ret == 0.
err_out dereferences vfb if ret == 0, but in our case vfb is still NULL.
Fix this by assigning sensible error to ret.
Found by Linux Verification Center (linuxtesting.org) with SVACE
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru> Cc: stable@vger.kernel.org Fixes: 810b3e1683d0 ("drm/vmwgfx: Support topology greater than texture size") Signed-off-by: Zack Rusin <zack.rusin@broadcom.com> Link: https://patchwork.freedesktop.org/patch/msgid/20241002122429.1981822-1-kniv@yandex-team.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the encoder itself in its possible_clones bitmask.
In the past nothing validated that drivers were populating
possible_clones correctly, but that changed in commit 74d2aacbe840 ("drm: Validate encoder->possible_clones").
Looks like radeon never got the memo and is still not
following the rules 100% correctly.
This results in some warnings during driver initialization:
Bogus possible_clones: [ENCODER:46:TV-46] possible_clones=0x4 (full encoder mask=0x7)
WARNING: CPU: 0 PID: 170 at drivers/gpu/drm/drm_mode_config.c:615 drm_mode_config_validate+0x113/0x39c
...
Cc: Alex Deucher <alexander.deucher@amd.com> Cc: amd-gfx@lists.freedesktop.org Fixes: 74d2aacbe840 ("drm: Validate encoder->possible_clones") Reported-by: Erhard Furtner <erhard_f@mailbox.org> Closes: https://lore.kernel.org/dri-devel/20241009000321.418e4294@yea/ Tested-by: Erhard Furtner <erhard_f@mailbox.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3b6e7d40649c0d75572039aff9d0911864c689db) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an application uses SQPOLL, it must wait for the SQPOLL thread to
consume SQE entries, if it fails to get an sqe when calling
io_uring_get_sqe(). It can do so by calling io_uring_enter(2) with the
flag value of IORING_ENTER_SQ_WAIT. In liburing, this is generally done
with io_uring_sqring_wait(). There's a natural expectation that once
this call returns, a new SQE entry can be retrieved, filled out, and
submitted. However, the kernel uses the cached sq head to determine if
the SQRING is full or not. If the SQPOLL thread is currently in the
process of submitting SQE entries, it may have updated the cached sq
head, but not yet committed it to the SQ ring. Hence the kernel may find
that there are SQE entries ready to be consumed, and return successfully
to the application. If the SQPOLL thread hasn't yet committed the SQ
ring entries by the time the application returns to userspace and
attempts to get a new SQE, it will fail getting a new SQE.
Fix this by having io_sqring_full() always use the user visible SQ ring
head entry, rather than the internally cached one.
So rq_qos_wake_function() calls wake_up_process(data->task), which calls
try_to_wake_up(), which faults in raw_spin_lock_irqsave(&p->pi_lock).
p comes from data->task, and data comes from the waitqueue entry, which
is stored on the waiter's stack in rq_qos_wait(). Analyzing the core
dump with drgn, I found that the waiter had already woken up and moved
on to a completely unrelated code path, clobbering what was previously
data->task. Meanwhile, the waker was passing the clobbered garbage in
data->task to wake_up_process(), leading to the crash.
What's happening is that in between rq_qos_wake_function() deleting the
waitqueue entry and calling wake_up_process(), rq_qos_wait() is finding
that it already got a token and returning. The race looks like this:
rq_qos_wait() rq_qos_wake_function()
==============================================================
prepare_to_wait_exclusive()
data->got_token = true;
list_del_init(&curr->entry);
if (data.got_token)
break;
finish_wait(&rqw->wait, &data.wq);
^- returns immediately because
list_empty_careful(&wq_entry->entry)
is true
... return, go do something else ...
wake_up_process(data->task)
(NO LONGER VALID!)-^
Normally, finish_wait() is supposed to synchronize against the waker.
But, as noted above, it is returning immediately because the waitqueue
entry has already been removed from the waitqueue.
The bug is that rq_qos_wake_function() is accessing the waitqueue entry
AFTER deleting it. Note that autoremove_wake_function() wakes the waiter
and THEN deletes the waitqueue entry, which is the proper order.
Fix it by swapping the order. We also need to use
list_del_init_careful() to match the list_empty_careful() in
finish_wait().
Since X86_FEATURE_ENTRY_IBPB will invalidate all harmful predictions
with IBPB, no software-based untraining of returns is needed anymore.
Currently, this change affects retbleed and SRSO mitigations so if
either of the mitigations is doing IBPB and the other one does the
software sequence, the latter is not needed anymore.
entry_ibpb() is designed to follow Intel's IBPB specification regardless
of CPU. This includes invalidating RSB entries.
Hence, if IBPB on VMEXIT has been selected, entry_ibpb() as part of the
RET untraining in the VMEXIT path will take care of all BTB and RSB
clearing so there's no need to explicitly fill the RSB anymore.
entry_ibpb() should invalidate all indirect predictions, including return
target predictions. Not all IBPB implementations do this, in which case the
fallback is RSB filling.
Prevent SRSO-style hijacks of return predictions following IBPB, as the return
target predictor can be corrupted before the IBPB completes.
Set this flag if the CPU has an IBPB implementation that does not
invalidate return target predictions. Zen generations < 4 do not flush
the RSB when executing an IBPB and this bug flag denotes that.
AMD's initial implementation of IBPB did not clear the return address
predictor. Beginning with Zen4, AMD's IBPB *does* clear the return address
predictor. This behavior is enumerated by CPUID.80000008H:EBX.IBPB_RET[30].
Define X86_FEATURE_AMD_IBPB_RET for use in KVM_GET_SUPPORTED_CPUID,
when determining cross-vendor capabilities.
Suggested-by: Venkatesh Srinivas <venkateshs@chromium.org> Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parameters for the diag 0x258 are real addresses, not virtual, but
KVM was using them as virtual addresses. This only happened to work, since
the Linux kernel as a guest used to have a 1:1 mapping for physical vs
virtual addresses.
Fix KVM so that it correctly uses the addresses as real addresses.
According to the VT220 specification the possible character combinations
sent on RETURN are only CR or CRLF [0].
The Return key sends either a CR character (0/13) or a CR
character (0/13) and an LF character (0/10), depending on the
set/reset state of line feed/new line mode (LNM).
The sclp/vt220 driver however uses LFCR. This can confuse tools, for
example the kunit runner.
Previously, the domain_context_clear() function incorrectly called
pci_for_each_dma_alias() to set up context entries for non-PCI devices.
This could lead to kernel hangs or other unexpected behavior.
Add a check to only call pci_for_each_dma_alias() for PCI devices. For
non-PCI devices, domain_context_clear_one() is called directly.
Putting the cpumask on the stack is deprecated for a long time (since 2d3854a37e8), as these can be big. Given that, change the on-stack
allocation of allowed_mask to be dynamically allocated.
Fixes: f011c9cf04c0 ("io_uring/sqpoll: do not allow pinning outside of cpuset") Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com> Link: https://lore.kernel.org/r/20240916111150.1266191-1-felix.moessbauer@siemens.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit ensured that SQPOLL cannot be setup with a CPU that
isn't in the current tasks cpuset, but it also dropped testing whether
the CPU is valid in the first place. Without that, if a task passes in
a CPU value that is too high, the following KASAN splat can get
triggered:
BUG: KASAN: stack-out-of-bounds in io_sq_offload_create+0x858/0xaa4
Read of size 8 at addr ffff800089bc7b90 by task wq-aff.t/1391
The submit queue polling threads are userland threads that just never
exit to the userland. When creating the thread with IORING_SETUP_SQ_AFF,
the affinity of the poller thread is set to the cpu specified in
sq_thread_cpu. However, this CPU can be outside of the cpuset defined
by the cgroup cpuset controller. This violates the rules defined by the
cpuset controller and is a potential issue for realtime applications.
In b7ed6d8ffd6 we fixed the default affinity of the poller thread, in
case no explicit pinning is required by inheriting the one of the
creating task. In case of explicit pinning, the check is more
complicated, as also a cpu outside of the parent cpumask is allowed.
We implemented this by using cpuset_cpus_allowed (that has support for
cgroup cpusets) and testing if the requested cpu is in the set.
Lack of check for copy-on-write (COW) mapping in drm_gem_shmem_mmap
allows users to call mmap with PROT_WRITE and MAP_PRIVATE flag
causing a kernel panic due to BUG_ON in vmf_insert_pfn_prot:
BUG_ON((vma->vm_flags & VM_PFNMAP) && is_cow_mapping(vma->vm_flags));
Return -EINVAL early if COW mapping is detected.
This bug affects all drm drivers using default shmem helpers.
It can be reproduced by this simple example:
void *ptr = mmap(0, size, PROT_WRITE, MAP_PRIVATE, fd, mmap_offset);
ptr[0] = 0;
Fixes: 2194a63a818d ("drm: Add library for shmem backed GEM objects") Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Eric Anholt <eric@anholt.net> Cc: Rob Herring <robh@kernel.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v5.2+ Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com> Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20240520100514.925681-1-jacek.lawrynowicz@linux.intel.com
[ Sherry: bp to fix CVE-2024-39497, ignore context change due to missing
commit 21aa27ddc582 ("drm/shmem-helper: Switch to reservation lock") ] Signed-off-by: Sherry Yang <sherry.yang@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use {READ,WRITE}_ONCE() to access kvm->last_boosted_vcpu to ensure the
loads and stores are atomic. In the extremely unlikely scenario the
compiler tears the stores, it's theoretically possible for KVM to attempt
to get a vCPU using an out-of-bounds index, e.g. if the write is split
into multiple 8-bit stores, and is paired with a 32-bit load on a VM with
257 vCPUs:
Tasklets have an inherent problem with memory corruption. The function
tasklet_action_common calls tasklet_trylock, then it calls the tasklet
callback and then it calls tasklet_unlock. If the tasklet callback frees
the structure that contains the tasklet or if it calls some code that may
free it, tasklet_unlock will write into free memory.
The commits 8e14f610159d and d9a02e016aaf try to fix it for dm-crypt, but
it is not a sufficient fix and the data corruption can still happen [1].
There is no fix for dm-verity and dm-verity will write into free memory
with every tasklet-processed bio.
There will be atomic workqueues implemented in the kernel 6.9 [2]. They
will have better interface and they will not suffer from the memory
corruption problem.
But we need something that stops the memory corruption now and that can be
backported to the stable kernels. So, I'm proposing this commit that
disables tasklets in both dm-crypt and dm-verity. This commit doesn't
remove the tasklet support, because the tasklet code will be reused when
atomic workqueues will be implemented.
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Sherry: bp to fix CVE-2023-52530, resolved minor conflicts in
net/mac80211/cfg.c because of context change due to missing commit 23a5f0af6ff4 ("wifi: mac80211: remove cipher scheme support") ccdde7c74ffd ("wifi: mac80211: properly implement MLO key handling")] Signed-off-by: Sherry Yang <sherry.yang@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -ENOSYS from memfd_secret() syscall if !can_set_direct_map(). This
is the case for example on some arm64 configurations, where marking 4k
PTEs in the direct map not present can only be done if the direct map is
set up at 4k granularity in the first place (as ARM's break-before-make
semantics do not easily allow breaking apart large/gigantic pages).
More precisely, on arm64 systems with !can_set_direct_map(),
set_direct_map_invalid_noflush() is a no-op, however it returns success
(0) instead of an error. This means that memfd_secret will seemingly
"work" (e.g. syscall succeeds, you can mmap the fd and fault in pages),
but it does not actually achieve its goal of removing its memory from the
direct map.
Note that with this patch, memfd_secret() will start erroring on systems
where can_set_direct_map() returns false (arm64 with
CONFIG_RODATA_FULL_DEFAULT_ENABLED=n, CONFIG_DEBUG_PAGEALLOC=n and
CONFIG_KFENCE=n), but that still seems better than the current silent
failure. Since CONFIG_RODATA_FULL_DEFAULT_ENABLED defaults to 'y', most
arm64 systems actually have a working memfd_secret() and aren't be
affected.
From going through the iterations of the original memfd_secret patch
series, it seems that disabling the syscall in these scenarios was the
intended behavior [1] (preferred over having
set_direct_map_invalid_noflush return an error as that would result in
SIGBUSes at page-fault time), however the check for it got dropped between
v16 [2] and v17 [3], when secretmem moved away from CMA allocations.
Link: https://lkml.kernel.org/r/20241001080056.784735-1-roypat@amazon.co.uk Fixes: 1507f51255c9 ("mm: introduce memfd_secret system call to create "secret" memory areas") Signed-off-by: Patrick Roy <roypat@amazon.co.uk> Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Cc: Alexander Graf <graf@amazon.com> Cc: David Hildenbrand <david@redhat.com> Cc: James Gowans <jgowans@amazon.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got a bad pud error and lost a 1GB HugeTLB when calling swapoff. The
problem can be reproduced by the following steps:
1. Allocate an anonymous 1GB HugeTLB and some other anonymous memory.
2. Swapout the above anonymous memory.
3. run swapoff and we will get a bad pud error in kernel message:
We can tell that pud_clear_bad is called by pud_none_or_clear_bad in
unuse_pud_range() by ftrace. And therefore the HugeTLB pages will never
be freed because we lost it from page table. We can skip HugeTLB pages
for unuse_vma to fix it.
Link: https://lkml.kernel.org/r/20241015014521.570237-1-liushixin2@huawei.com Fixes: 0fe6e20b9c4c ("hugetlb, rmap: add reverse mapping for hugepage") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Acked-by: Muchun Song <muchun.song@linux.dev> Cc: Naoya Horiguchi <nao.horiguchi@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"A VMAPP with {V, Alloc}=={0, x} is self-synchronizing, This means the ITS
command queue does not show the command as consumed until all of its
effects are completed."
Furthermore, VSYNC is allowed to deliver an SError when referencing a
non existent VPE.
By these definitions, a VMAPP followed by a VSYNC is a bug, as the
later references a VPE that has been unmapped by the former.
Fix it by eliding the VSYNC in this scenario.
Fixes: 64edfaa9a234 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP") Signed-off-by: Nianyao Tang <tangnianyao@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Zenghui Yu <yuzenghui@huawei.com> Link: https://lore.kernel.org/r/20240406022737.3898763-1-tangnianyao@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A boot delay was introduced by commit 79540d133ed6 ("net: macb: Fix
handling of fixed-link node"). This delay was caused by the call to
`mdiobus_register()` in cases where a fixed-link PHY was present. The
MDIO bus registration triggered unnecessary PHY address scans, leading
to a 20-second delay due to attempts to detect Clause 45 (C45)
compatible PHYs, despite no MDIO bus being attached.
The commit 79540d133ed6 ("net: macb: Fix handling of fixed-link node")
was originally introduced to fix a regression caused by commit 7897b071ac3b4 ("net: macb: convert to phylink"), which caused the driver
to misinterpret fixed-link nodes as PHY nodes. This resulted in warnings
like:
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
...
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
This patch reworks the logic to avoid registering and allocation of the
MDIO bus when:
- The device tree contains a fixed-link node.
- There is no "mdio" child node in the device tree.
If a child node named "mdio" exists, the MDIO bus will be registered to
support PHYs attached to the MACB's MDIO bus. Otherwise, with only a
fixed-link, the MDIO bus is skipped.
Tested on a sama5d35 based system with a ksz8863 switch attached to
macb0.
Fixes: 79540d133ed6 ("net: macb: Fix handling of fixed-link node") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241013052916.3115142-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simulate_ldr_literal() code always loads a 64-bit quantity, and when
simulating a 32-bit load into a 'W' register, it discards the most
significant 32 bits. For big-endian kernels this means that the relevant
bits are discarded, and the value returned is the the subsequent 32 bits
in memory (i.e. the value at addr + 4).
Additionally, simulate_ldr_literal() and simulate_ldrsw_literal() use a
plain C load, which the compiler may tear or elide (e.g. if the target
is the zero register). Today this doesn't happen to matter, but it may
matter in future if trampoline code uses a LDR (literal) or LDRSW
(literal).
Update simulate_ldr_literal() and simulate_ldrsw_literal() to use an
appropriately-sized READ_ONCE() to perform the access, which avoids
these problems.
The simulate_ldr_literal() and simulate_ldrsw_literal() functions are
unsafe to use for uprobes. Both functions were originally written for
use with kprobes, and access memory with plain C accesses. When uprobes
was added, these were reused unmodified even though they cannot safely
access user memory.
There are three key problems:
1) The plain C accesses do not have corresponding extable entries, and
thus if they encounter a fault the kernel will treat these as
unintentional accesses to user memory, resulting in a BUG() which
will kill the kernel thread, and likely lead to further issues (e.g.
lockup or panic()).
2) The plain C accesses are subject to HW PAN and SW PAN, and so when
either is in use, any attempt to simulate an access to user memory
will fault. Thus neither simulate_ldr_literal() nor
simulate_ldrsw_literal() can do anything useful when simulating a
user instruction on any system with HW PAN or SW PAN.
3) The plain C accesses are privileged, as they run in kernel context,
and in practice can access a small range of kernel virtual addresses.
The instructions they simulate have a range of +/-1MiB, and since the
simulated instructions must itself be a user instructions in the
TTBR0 address range, these can address the final 1MiB of the TTBR1
acddress range by wrapping downwards from an address in the first
1MiB of the TTBR0 address range.
In contemporary kernels the last 8MiB of TTBR1 address range is
reserved, and accesses to this will always fault, meaning this is no
worse than (1).
Historically, it was theoretically possible for the linear map or
vmemmap to spill into the final 8MiB of the TTBR1 address range, but
in practice this is extremely unlikely to occur as this would
require either:
* Having enough physical memory to fill the entire linear map all the
way to the final 1MiB of the TTBR1 address range.
* Getting unlucky with KASLR randomization of the linear map such
that the populated region happens to overlap with the last 1MiB of
the TTBR address range.
... and in either case if we were to spill into the final page there
would be larger problems as the final page would alias with error
pointers.
Practically speaking, (1) and (2) are the big issues. Given there have
been no reports of problems since the broken code was introduced, it
appears that no-one is relying on probing these instructions with
uprobes.
Avoid these issues by not allowing uprobes on LDR (literal) and LDRSW
(literal), limiting the use of simulate_ldr_literal() and
simulate_ldrsw_literal() to kprobes. Attempts to place uprobes on LDR
(literal) and LDRSW (literal) will be rejected as
arm_probe_decode_insn() will return INSN_REJECTED. In future we can
consider introducing working uprobes support for these instructions, but
this will require more significant work.
Fixes: 9842ceae9fa8 ("arm64: Add uprobe support") Cc: stable@vger.kernel.org Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20241008155851.801546-2-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Andrew pointed out, it will make sense that the PTP core
checked timespec64 struct's tv_sec and tv_nsec range before calling
ptp->info->settime64().
As the man manual of clock_settime() said, if tp.tv_sec is negative or
tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL,
which include dynamic clocks which handles PTP clock, and the condition is
consistent with timespec64_valid(). As Thomas suggested, timespec64_valid()
only check the timespec is valid, but not ensure that the time is
in a valid range, so check it ahead using timespec64_valid_strict()
in pc_clock_settime() and return -EINVAL if not valid.
There are some drivers that use tp->tv_sec and tp->tv_nsec directly to
write registers without validity checks and assume that the higher layer
has checked it, which is dangerous and will benefit from this, such as
hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(),
and some drivers can remove the checks of itself.
Cc: stable@vger.kernel.org Fixes: 0606f422b453 ("posix clocks: Introduce dynamic clocks") Acked-by: Richard Cochran <richardcochran@gmail.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Link: https://patch.msgid.link/20241009072302.1754567-2-ruanjinjie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warnings when CONFIG_FSL_ENETC_MDIO is not enabled.
The detailed warnings are shown as follows.
include/linux/fsl/enetc_mdio.h:62:18: warning: no previous prototype for function 'enetc_hw_alloc' [-Wmissing-prototypes]
62 | struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
| ^
include/linux/fsl/enetc_mdio.h:62:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
62 | struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
| ^
| static
8 warnings generated.
Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl") Cc: stable@vger.kernel.org Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202410102136.jQHZOcS4-lkp@intel.com/ Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241011030103.392362-1-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xdp_drops statistic indicates the number of XDP frames dropped in
the Rx direction. However, enetc_xdp_drop() is also used in XDP_TX and
XDP_REDIRECT actions. If frame loss occurs in these two actions, the
frames loss count should not be included in xdp_drops, because there
are already xdp_tx_drops and xdp_redirect_failures to count the frame
loss of these two actions, so it's better to remove xdp_drops statistic
from enetc_xdp_drop() and increase xdp_drops in XDP_DROP action.
Fixes: 7ed2bc80074e ("net: enetc: add support for XDP_TX") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241010092056.298128-2-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reports uninitialized memory access in udf_rename() when updating
checksum of '..' directory entry of a moved directory. This is indeed
true as we pass on-stack diriter.fi to the udf_update_tag() and because
that has only struct fileIdentDesc included in it and not the impUse or
name fields, the checksumming function is going to checksum random stack
contents beyond the end of the structure. This is actually harmless
because the following udf_fiiter_write_fi() will recompute the checksum
from on-disk buffers where everything is properly included. So all that
is needed is just removing the bogus calculation.
Nobody uses the bh returned from udf_expand_dir_adinicb(). Don't return
it.
Signed-off-by: Jan Kara <jack@suse.cz>
[cascardo: skip backport of 101ee137d32a ("udf: Drop VARCONV support")] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is an error when adding extent to the directory to expand it,
make sure to propagate the error up properly. This is not expected to
happen currently but let's make the code more futureproof.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old directory iteration code that is now unused.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_link() to use new directory iteration code for adding entry
into the directory.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_mkdir() to new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_add_nondir() to new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement function udf_fiiter_add_entry() adding new directory entries
using new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_unlink() to new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_rmdir() to use new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert empty_dir() to new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_get_parent() to use udf_fiiter_find_entry().
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_lookup() to use udf_fiiter_find_entry() for looking up
directory entries.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_readdir() to new directory iteration functions.
Signed-off-by: Jan Kara <jack@suse.cz>
[cascardo: conflict due to skipped 59a16786fa7a ("udf: replace ll_rw_block()")] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_rename() to use new directory iteration code.
Reported-by: syzbot+0eaad3590d65102b9391@syzkaller.appspotmail.com Reported-by: syzbot+b7fc73213bc2361ab650@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide function udf_fiiter_delete_entry() to mark directory entry as
deleted using new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement searching for directory entry - udf_fiiter_find_entry() -
using new directory iteration code.
Reported-by: syzbot+69c9fdccc6dd08961d34@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is just one caller of udf_expand_dir_adinicb(). Move the function
to its caller into namei.c as it is more about directory handling than
anything else anyway.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert udf_expand_dir_adinicb() to new directory iteration code.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new support code for iterating directory entries. The code is also
more carefully verifying validity of on-disk directory entries to avoid
crashes on malicious media.
Signed-off-by: Jan Kara <jack@suse.cz>
[cascardo: use ll_rw_block instead of bh_readahead_batch] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a problem with simultaneous audio output to headphones and
speakers, and when headphones are turned off, the speakers also turn
off and do not turn them on.
However, it was found that if you boot linux immediately after windows,
there are no such problems. When comparing alsa-info, the only difference
is the different configuration of Node 0x1d:
working conf. (windows): Pin-ctls: 0x80: HP
not working (linux): Pin-ctls: 0xc0: OUT HP
This patch disable the AC_PINCTL_OUT_EN bit of Node 0x1d and fixes the
described problem.
As advised by Documentation/networking/napi.rst, masking IRQs after
calling napi_schedule can be racy. Avoid this by only masking/scheduling
if napi_schedule_prep returns true.
Fixes: 9e2bc267e780 ("net: axienet: Use NAPI for TX completion path") Fixes: cc37610caaf8 ("net: axienet: implement NAPI and GRO receive") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20240913145711.2284295-1-sean.anderson@linux.dev Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper waiting for a listener port can match any socket whose
hexadecimal representation of source or destination addresses
matches that of the given port.
Additionally, any socket state is accepted.
All the above can let the helper return successfully before the
relevant listener is actually ready, with unexpected results.
So far I could not find any related failure in the netdev CI, but
the next patch is going to make the critical event more easily
reproducible.
Address the issue matching the port hex only vs the relevant socket
field and additionally checking the socket state for TCP sockets.
softirq may get lost if an Rx interrupt comes before we call
napi_enable. Move napi_enable in front of axienet_setoptions(), which
turns on the device, to address the issue.
Link: https://lists.gnu.org/archive/html/qemu-devel/2024-07/msg06160.html Fixes: cc37610caaf8 ("net: axienet: implement NAPI and GRO receive") Signed-off-by: Andy Chiu <andy.chiu@sifive.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot has reported that it can hit the warning in
ext4_dio_write_end_io() because i_size < i_disksize. Indeed the
reproducer creates a race between DIO IO completion and truncate
expanding the file and thus ext4_dio_write_end_io() sees an inconsistent
inode state where i_disksize is already updated but i_size is not
updated yet. Since we are careful when setting up DIO write and consider
it extending (and thus performing the IO synchronously with i_rwsem held
exclusively) whenever it goes past either of i_size or i_disksize, we
can use the same test during IO completion without risking entering
ext4_handle_inode_extension() without i_rwsem held. This way we make it
obvious both i_size and i_disksize are large enough when we report DIO
completion without relying on unreliable WARN_ON.
Reported-by: <syzbot+47479b71cdfc78f56d30@syzkaller.appspotmail.com> Fixes: 91562895f803 ("ext4: properly sync file size update after O_SYNC direct IO") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/20231130095653.22679-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling ip6_route_lookup() for the packet arriving on the VRF
interface, the result is always the real (slave) interface. Expect this
when validating the result.
Fixes: acc641ab95b66 ("netfilter: rpfilter/fib: Populate flowic_l3mdev field") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multicast packets received on an interface bound to a VRF are marked as
belonging to the VRF and the skb device is updated to point to the VRF
device itself. This was fine even when a route was associated to a
device as when performing a fib table lookup 'oif' in fib6_table_lookup
(coming from 'skb->dev->ifindex' in ip6_route_input) was set to 0 when
FLOWI_FLAG_SKIP_NH_OIF was set.
With commit 40867d74c374 ("net: Add l3mdev index to flow struct and
avoid oif reset for port devices") this is not longer true and multicast
traffic is not received on the original interface.
Instead of adding back a similar check in fib6_table_lookup determine
the dst using the original ifindex for multicast VRF traffic. To make
things consistent across the function do the above for all strict
packets, which was the logic before commit 6f12fa775530 ("vrf: mark skb
for multicast or link-local as enslaved to VRF"). Note that reverting to
this behavior should be fine as the change was about marking packets
belonging to the VRF, not about their dst.
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20221220171825.1172237-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif
reset for port devices") adds a new entry (flowi_l3mdev) in the common
flow struct used for indicating the l3mdev index for later rule and
table matching.
The l3mdev_update_flow() has been adapted to properly set the
flowi_l3mdev based on the flowi_oif/flowi_iif. In fact, when a valid
flowi_iif is supplied to the l3mdev_update_flow(), this function can
update the flowi_l3mdev entry only if it has not yet been set (i.e., the
flowi_l3mdev entry is equal to 0).
The SRv6 End.DT6 behavior in VRF mode leverages a VRF device in order to
force the routing lookup into the associated routing table. This routing
operation is performed by seg6_lookup_any_nextop() preparing a flowi6
data structure used by ip6_route_input_lookup() which, in turn,
(indirectly) invokes l3mdev_update_flow().
However, seg6_lookup_any_nexthop() does not initialize the new
flowi_l3mdev entry which is filled with random garbage data. This
prevents l3mdev_update_flow() from properly updating the flowi_l3mdev
with the VRF index, and thus SRv6 End.DT6 (VRF mode)/DT46 behaviors are
broken.
This patch correctly initializes the flowi6 instance allocated and used
by seg6_lookup_any_nexhtop(). Specifically, the entire flowi6 instance
is wiped out: in case new entries are added to flowi/flowi6 (as happened
with the flowi_l3mdev entry), we should no longer have incorrectly
initialized values. As a result of this operation, the value of
flowi_l3mdev is also set to 0.
The proposed fix can be tested easily. Starting from the commit
referenced in the Fixes, selftests [1],[2] indicate that the SRv6
End.DT6 (VRF mode)/DT46 behaviors no longer work correctly. By applying
this patch, those behaviors are back to work properly again.
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: Anton Makarov <am@3a-alliance.com> Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220608091917.20345-1-andrea.mayer@uniroma2.it Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ido reported that the commit referenced in the Fixes tag broke
a gre use case with dummy devices. Add a check to ip_tunnel_init_flow
to see if the oif is an l3mdev port and if so set the oif to 0 to
avoid the oif comparison in fib_lookup_good_nhc.
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit referenced in the Fixes tag no longer changes the
flow oif to the l3mdev ifindex. A xfrm use case was expecting
the flowi_oif to be the VRF if relevant and the change broke
that test. Update xfrm_bundle_create to pass oif if set and any
potential flowi_l3mdev if oif is not set.
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 42c306ed7233 ("block, bfq: don't break merge chain in
bfq_split_bfqq()"), if the current procress is the last holder of bfqq,
the bfqq can be freed after bfq_split_bfqq(). Hence recored the bfqq and
then access bfqq->waker_bfqq may trigger UAF. What's more, the waker_bfqq
may in the merge chain of bfqq, hence just recored waker_bfqq is still
not safe.
Fix the problem by adding a helper bfq_waker_bfqq() to check if
bfqq->waker_bfqq is in the merge chain, and current procress is the only
holder.
Calling into kthread unparking unconditionally is mostly harmless when
the kthread is already unparked. The wake up is then simply ignored
because the target is not in TASK_PARKED state.
However if the kthread is per CPU, the wake up is preceded by a call
to kthread_bind() which expects the task to be inactive and in
TASK_PARKED state, which obviously isn't the case if it is unparked.
As a result, calling kthread_stop() on an unparked per-cpu kthread
triggers such a warning:
The `nouveau_dmem_copy_one` function ensures that the copy push command is
sent to the device firmware but does not track whether it was executed
successfully.
In the case of a copy error (e.g., firmware or hardware failure), the
copy push command will be sent via the firmware channel, and
`nouveau_dmem_copy_one` will likely report success, leading to the
`migrate_to_ram` function returning a dirty HIGH_USER page to the user.
This can result in a security vulnerability, as a HIGH_USER page that may
contain sensitive or corrupted data could be returned to the user.
To prevent this vulnerability, we allocate a zero page. Thus, in case of
an error, a non-dirty (zero) page will be returned to the user.
Fixes: 5be73b690875 ("drm/nouveau/dmem: device memory helpers for SVM") Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com> Co-developed-by: Gal Shalom <GalShalom@Nvidia.com> Signed-off-by: Gal Shalom <GalShalom@Nvidia.com> Reviewed-by: Ben Skeggs <bskeggs@nvidia.com> Cc: stable@vger.kernel.org Signed-off-by: Danilo Krummrich <dakr@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-3-ymaman@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a previous fix, the in-kernel path-manager has been modified not to
retrigger the removal of a subflow if it was already closed, e.g. when
the initial subflow is removed, but kept in the subflows list.
To be complete, this fix should also skip the subflows that are in any
closing state: mptcp_close_ssk() will initiate the closure, but the
switch to the TCP_CLOSE state depends on the other peer.
Fixes: 58e1b66b4e4b ("mptcp: pm: do not remove already closed subflows") Cc: stable@vger.kernel.org Suggested-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241008-net-mptcp-fallback-fixes-v1-4-c6fb8e93e551@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303") Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()] Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have recently noticed the exact same KASAN splat as in commit 6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket
creation fails"). The problem is that commit did not fully address the
problem, as some pf->create implementations do not use sk_common_release
in their error paths.
For example, we can use the same reproducer as in the above commit, but
changing ping to arping. arping uses AF_PACKET socket and if packet_create
fails, it will just sk_free the allocated sk object.
While we could chase all the pf->create implementations and make sure they
NULL the freed sk object on error from the socket, we can't guarantee
future protocols will not make the same mistake.
So it is easier to just explicitly NULL the sk pointer upon return from
pf->create in __sock_create. We do know that pf->create always releases the
allocated sk object on error, so if the pointer is not NULL, it is
definitely dangling.
Fixes: 6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket creation fails") Signed-off-by: Ignat Korchagin <ignat@cloudflare.com> Cc: stable@vger.kernel.org Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20241003170151.69445-1-ignat@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue arises because, upon closing the file descriptor (which happens
when we interrupt `kmscube`), the active performance monitor is not
stopped. Although all perfmons are destroyed in `v3d_perfmon_close_file()`,
the active performance monitor's pointer (`v3d->active_perfmon`) is still
retained.
If `kmscube` is run again, the driver will attempt to stop the active
performance monitor using the stale pointer in `v3d->active_perfmon`.
However, this pointer is no longer valid because the previous process has
already terminated, and all performance monitors associated with it have
been destroyed and freed.
To fix this, when the active performance monitor belongs to a given
process, explicitly stop it before destroying and freeing it.
Cc: stable@vger.kernel.org # v5.15+ Closes: https://github.com/raspberrypi/linux/issues/6389 Fixes: 26a4dc29b74a ("drm/v3d: Expose performance counters to userspace") Signed-off-by: Maíra Canal <mcanal@igalia.com> Reviewed-by: Juan A. Suarez <jasuarez@igalia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20241004130625.918580-2-mcanal@igalia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the uninitialized symbol 'rv' in the function ish_fw_xfer_direct_dma
to resolve the following warning from the smatch tool:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:714 ish_fw_xfer_direct_dma()
error: uninitialized symbol 'rv'.
Initialize 'rv' to 0 to prevent undefined behavior from uninitialized
access.
JieLi tends to use SCSI via USB Mass Storage to implement their own
proprietary commands instead of implementing another USB interface.
Enumerating it as a generic mass storage device will lead to a Hardware
Error sense key get reported.
Ignore this bogus device to prevent appearing a unusable sdX device
file.
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Some Plantronics headset as the below send an unexcept opposite
volume key's HID report for each volume key press after 200ms, like
unecepted Volume Up Key following Volume Down key pressed by user.
This patch adds a quirk to hid-plantronics for these devices, which
will ignore the second unexcepted opposite volume key if it happens
within 220ms from the last one that was handled.
Plantronics EncorePro 500 Series (047f:431e)
Plantronics Blackwire_3325 Series (047f:430c)
The patch was tested on the mentioned model, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected per test
result.
Because drivers/dax/kmem.c calls add_memory_driver_managed() during
onlining CXL memory, which makes "System RAM (kmem)" a descendant of "CXL
Window X". This confuses region_intersects(), which expects all "System
RAM" resources to be at the top level of iomem_resource. This can lead to
bugs.
For example, when the following command line is executed to write some
memory in CXL memory range via /dev/mem,
$ dd if=data of=/dev/mem bs=$((1 << 10)) seek=$((0x490000000 >> 10)) count=1
dd: error writing '/dev/mem': Bad address
1+0 records in
0+0 records out
0 bytes copied, 0.0283507 s, 0.0 kB/s
the command fails as expected. However, the error code is wrong. It
should be "Operation not permitted" instead of "Bad address". More
seriously, the /dev/mem permission checking in devmem_is_allowed() passes
incorrectly. Although the accessing is prevented later because ioremap()
isn't allowed to map system RAM, it is a potential security issue. During
command executing, the following warning is reported in the kernel log for
calling ioremap() on system RAM.
ioremap on RAM at 0x0000000490000000 - 0x0000000490000fff
WARNING: CPU: 2 PID: 416 at arch/x86/mm/ioremap.c:216 __ioremap_caller.constprop.0+0x131/0x35d
Call Trace:
memremap+0xcb/0x184
xlate_dev_mem_ptr+0x25/0x2f
write_mem+0x94/0xfb
vfs_write+0x128/0x26d
ksys_write+0xac/0xfe
do_syscall_64+0x9a/0xfd
entry_SYSCALL_64_after_hwframe+0x4b/0x53
The details of command execution process are as follows. In the above
resource tree, "System RAM" is a descendant of "CXL Window 0" instead of a
top level resource. So, region_intersects() will report no System RAM
resources in the CXL memory region incorrectly, because it only checks the
top level resources. Consequently, devmem_is_allowed() will return 1
(allow access via /dev/mem) for CXL memory region incorrectly.
Fortunately, ioremap() doesn't allow to map System RAM and reject the
access.
So, region_intersects() needs to be fixed to work correctly with the
resource tree with "System RAM" not at top level as above. To fix it, if
we found a unmatched resource in the top level, we will continue to search
matched resources in its descendant resources. So, we will not miss any
matched resources in resource tree anymore.
In the new implementation, an example resource tree
Using the device-managed version allows to simplify clean-up in probe()
error path.
Additionally, this device-managed ensures proper cleanup, which helps to
resolve memory errors, page faults, btrfs going read-only, and btrfs
disk corruption.
Fixes: 4b2c53d93a4b ("SFH:Transport Driver to add support of AMD Sensor Fusion Hub (SFH)") Tested-by: Chris Hixon <linux-kernel-bugs@hixontech.com> Tested-by: Richard <hobbes1069@gmail.com> Tested-by: Skyler <skpu@pm.me> Reported-by: Chris Hixon <linux-kernel-bugs@hixontech.com> Closes: https://lore.kernel.org/all/3b129b1f-8636-456a-80b4-0f6cce0eef63@hixontech.com/ Link: https://bugzilla.kernel.org/show_bug.cgi?id=219331 Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mitchell Levy [Thu, 10 Oct 2024 23:57:31 +0000 (16:57 -0700)]
x86/fpu: Avoid writing LBR bit to IA32_XSS unless supported
There are two distinct CPU features related to the use of XSAVES and LBR:
whether LBR is itself supported and whether XSAVES supports LBR. The LBR
subsystem correctly checks both in intel_pmu_arch_lbr_init(), but the
XSTATE subsystem does not.
The LBR bit is only removed from xfeatures_mask_independent when LBR is not
supported by the CPU, but there is no validation of XSTATE support.
If XSAVES does not support LBR the write to IA32_XSS causes a #GP fault,
leaving the state of IA32_XSS unchanged, i.e. zero. The fault is handled
with a warning and the boot continues.
Consequently the next XRSTORS which tries to restore supervisor state fails
with #GP because the RFBM has zero for all supervisor features, which does
not match the XCOMP_BV field.
As XFEATURE_MASK_FPSTATE includes supervisor features setting up the FPU
causes a #GP, which ends up in fpu_reset_from_exception_fixup(). That fails
due to the same problem resulting in recursive #GPs until the kernel runs
out of stack space and double faults.
Prevent this by storing the supported independent features in
fpu_kernel_cfg during XSTATE initialization and use that cached value for
retrieving the independent feature bits to be written into IA32_XSS.
[ tglx: Massaged change log ]
Fixes: f0dccc9da4c0 ("x86/fpu/xstate: Support dynamic supervisor feature for LBR") Suggested-by: Thomas Gleixner <tglx@linutronix.de>
[ Mitchell Levy: Backport to 5.15, since struct fpu_config is not
introduced until 578971f4e228 and feature masks are not included in
said struct until 1c253ff2287f ] Signed-off-by: Mitchell Levy <levymitchell0@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20240812-xsave-lbr-fix-v3-1-95bac1bf62f4@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The refcount of CQ is not protected by locks. When CQ asynchronous
events and CQ destruction are concurrent, CQ may have been released,
which will cause UAF.
Use the xa_lock() to protect the CQ refcount.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://lore.kernel.org/r/20240412091616.370789-6-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Haixiao Yan <haixiao.yan.cn@windriver.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since introduced, mctp has been ignoring the returned value of
rtnl_register_module(), which could fail silently.
Handling the error allows users to view a module as an all-or-nothing
thing in terms of the rtnetlink functionality. This prevents syzkaller
from reporting spurious errors from its tests, where OOM often occurs
and module is automatically loaded.
projects / thirdparty / kernel / stable.git / log
