Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi). This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48665
John Crispin [Mon, 8 Feb 2016 08:26:19 +0000 (08:26 +0000)]
rampis: HLK-RM04 - Setup I2C as GPIO
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.
Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1
John Crispin [Mon, 8 Feb 2016 08:26:11 +0000 (08:26 +0000)]
ramips: HLK-RM04 - Fix push button functions
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48663
John Crispin [Mon, 8 Feb 2016 08:26:02 +0000 (08:26 +0000)]
ramips: HLK-RM04 - Remove power LED config
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48662
John Crispin [Mon, 8 Feb 2016 08:25:53 +0000 (08:25 +0000)]
base-files: For sysfixtime use hwclock if RTC available
On systems that have an RTC prefer it to the file-based time fixup (i.e.
use hwclock when there is a permanent clock instead of the faked up time
logic that is needed when there is not RTC).
We can't rely on hctosys kernel feature either as we're usually using
RTC as kernel modules which are usually being loaded after hctosys was
run, leading in the following error:
hctosys: unable to open rtc device (rtc0)
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48661
John Crispin [Mon, 8 Feb 2016 08:25:31 +0000 (08:25 +0000)]
lantiq: VGV7510KW22/VGV7519 update spi pinmux group
With the backport of the kernel 4.5 pinctrl-xway patches (3551609d & 826bca29) the pinmux group "spi" was splitted into "spi_di", "spi_do" &
"spi_clk". But the no longer existing group "spi" is still used by some
device tree source files.
This fixes the detection of the wireless chipset of the VGV7510KW22.
John Crispin [Mon, 8 Feb 2016 08:25:22 +0000 (08:25 +0000)]
lantiq: BTHOMEHUBV5A - explicit select the flash device
The stock u-boot doesn't disable unused flash banks. Therefore, the nand
driver tries to initialize a not connected NOR flash and the device
hangs on boot.
Workaround the issue by selecting the second flash bank (NAND).
Signed-off-by: Mathias Kresin <openwrt@kresin.me> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48657
Felix Fietkau [Sun, 7 Feb 2016 13:29:16 +0000 (13:29 +0000)]
build: don't add -fno-plt for ARC
Curent ARC toolchain fails to build libstdc++ if -fno-plt is used.
Lots of following error messages appear:
------------------->8------------------
...
staging_dir/toolchain-arc_arc700_gcc-arc-2015.06_uClibc-1.0.9/arc-openwrt-linux-uclibc/bin/ld:
BFD (GNU Binutils) 2.23.2 assertion fail elf32-arc.c:2786
collect2: error: ld returned 1 exit status
------------------->8------------------
In newer binutils (still in development) for ARC rewritten from
scratch this seem to not happen, so once new binutils for ARC hit
the street this patch might be reverted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Felix Fietkau <nbd@openwrt.org> Cc: Jo-Philipp Wich <jow@openwrt.org> Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48642
Rafał Miłecki [Sat, 6 Feb 2016 16:29:12 +0000 (16:29 +0000)]
mtd: detect image format when writing
Recently TRX checking code was changed to detect Seama format and don't
abort whole writing operation because of it. This isn't a good long-term
solution. It's a poor idea to teach every format handler recognizing all
possible formats. Instead it should be handled in a generic code which
should run check depending on the detected format.
This will also allow further improvements like fixing formats other than
TRX after replacing JFFS2.
Rafał Miłecki [Wed, 3 Feb 2016 09:38:42 +0000 (09:38 +0000)]
swconfig: support setting SWITCH_TYPE_LINK attributes
Supported syntax is inspired by ethtool. Example usages:
swconfig dev switch0 port 2 set link "duplex half speed 100"
swconfig dev switch0 port 2 set link "autoneg on"
Rafał Miłecki [Wed, 3 Feb 2016 09:33:38 +0000 (09:33 +0000)]
swconfig: add (PHY) generic helper setting port link
It's quite common for switches to have PHY per port so adding a generic
helper setting link state will help many drivers. It just needs an API
to access PHYs which this patch also adds.
Rafał Miłecki [Mon, 1 Feb 2016 12:42:00 +0000 (12:42 +0000)]
firmware-utils: add oseama tool for creating Seama entities
It has an important feature (compared to seama) of using multiple input
files, aligning them and padding zeroes until reaching a specified
absolute offset. This is needed for a proper flash layout on NAND. We
want kernel partition to be big enough to handle future updates without
a need to resize it and wipe whole "ubi" partition. It's important as
we don't want to lose block counters.
Rafał Miłecki [Mon, 1 Feb 2016 12:41:53 +0000 (12:41 +0000)]
kernel: mtdsplit: support Seama entity with UBI
Some D-Link routers (e.g. DIR-885L) have NAND and use Seama format. It
means OpenWrt will want to have UBI in Sseama entity and should be able
to detect it.
Rafał Miłecki [Mon, 1 Feb 2016 12:41:41 +0000 (12:41 +0000)]
kernel: mtdsplit: modify rootfs helpers to provide partition type
Our mtdsplit parsers may want to create partition with name choice based
on partition file system (e.g. SquashFS vs. JFFS2). This patch allows
passing extra argument pointing to variable that will be set properly.
Felix Fietkau [Mon, 1 Feb 2016 12:02:11 +0000 (12:02 +0000)]
gre: Support multicast configurable gre interfaces
UCI paramater multicast is added which allows to toggle multicast support on gre interfaces.
By default multicast support is enabled as gre tunnels are often used in combination with
routing protocols using multicast.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Signed-off-by: Nick Podolak <nicholas.podolak@dtechlabs.com>
SVN-Revision: 48596
Felix Fietkau [Sun, 31 Jan 2016 23:29:16 +0000 (23:29 +0000)]
build system: have tar use $SOURCE_DATE_EPOCH for --mtime
The --mtime argument to 'tar' sets the modification time for all files within
the archive, which determines the timestamp files will get when they are
extracted. In this case, rootfs and other tarballs will get mtimes which
correspond to the last commit timestamp of the build system, as reported by
git/subversion.
This is a step towards reproducible image builds.
Signed-off-by: bryan newbold <bnewbold@robocracy.org> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48586
Felix Fietkau [Sun, 31 Jan 2016 23:28:55 +0000 (23:28 +0000)]
add scripts/portable_date: wrapper around date for bsd/linux
date -r $unix_timestamp on bsd is equal to date -d @$unix_timestamp on
linux. To support reproducible builds and not loosing every timestamp
it's required to convert a unix timestamp into human readable timestamp
./scripts/portable_date $unix_timstamp +%T
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 48583
projects / thirdparty / openwrt.git / log
