Josef Bacik [Thu, 6 Aug 2015 17:49:46 +0000 (10:49 -0700)]
efinet: handle get_status() on buggy firmware properly
The EFI spec indicates that get_status() should return the address of the buffer
we passed into transmit to indicate the the buffer was transmitted. However we
have boxes where the firmware returns some arbitrary address instead, which
makes grub think that we've not sent anything. So since we have the SNP stuff
opened in exclusive mode just assume any non-NULL txbuf means that our transmit
occurred properly. This makes grub able to do its networking stuff properly on
our broken firmware. Thanks,
cc: Peter Jones <pjones@redhat.com> Signed-off-by: Josef Bacik <jbacik@fb.com>
fshelp: Add handling of "." and ".." and grub_fshelp_find_file_lookup.
Recent tests have discovered that many of our filesystems have flawed
handling of "." and "..". Rather than attempting to fix it in filesystems
themselves, make the common code fshelp aware of "." and ".." and handle
them in this layer. Add grub_fshelp_find_file_lookup for easy conversion
of BFS, HFS and exFAT which have the same problem and don't use fshelp.
mips_attributes was introduced to work around clang problems with
-msoft-float. Those problems are now fixed and moreover .gnu_attributes
itself is unportable and creates problem with clang.
Wimboot fails since the change above because it expects the "trailer"
initrd element on an aligned address.
This issue shows only when newc_name is used and the last initrd
entry has a not aligned size.
Michael Chang [Mon, 22 Jun 2015 08:45:27 +0000 (16:45 +0800)]
Fix missing byte order conversion in get_btrfs_fs_prefix function
Since btrfs on-disk format uses little-endian, the searched item types
(ROOT_REF, INODE_REF) need converting the byte order in order to
function properly on big-endian systems.
Andrei Borzenkov [Fri, 19 Jun 2015 17:47:43 +0000 (20:47 +0300)]
grub-probe: restructure code to make static analysis easier
Current code in probe() could not be verified to not contain memory leaks.
Restructure code and ensure grub_device_close is always called at the end of
loop.
Andrei Borzenkov [Tue, 16 Jun 2015 16:52:45 +0000 (19:52 +0300)]
efinet: enable hardware filters when opening interface
Exclusive open on SNP will close all existing protocol instances which
may disable all receive filters on interface. Reinstall them after we
opened protocol exclusively.
Also follow UEFI specification recommendation and stop interfaces when
closing them:
Unexpected system errors, reboots and hangs can occur if an OS is loaded
and the network devices are not Shutdown() and Stopped().
Also by: Mark Salter <msalter@redhat.com> Closes: 45204
Mark Salter [Fri, 15 Aug 2014 16:22:43 +0000 (12:22 -0400)]
Fix exit to EFI firmware
The current code for EFI grub_exit() calls grub_efi_fini() before
returning to firmware. In the case of ARM, this leaves a timer
event running which could lead to a firmware crash. This patch
changes this so that grub_machine_fini() is called with a NORETURN
flag. This allows machine-specific shutdown to happen as well
as the shutdown done by grub_efi_fini().
Jan Kara [Mon, 1 Jun 2015 12:28:46 +0000 (14:28 +0200)]
xfs: V5 filesystem format support
Add support for new XFS on disk format. We have to handle optional
filetype fields in directory entries, additional CRC, LSN, UUID entries
in some structures, etc.
Paul Menzel [Wed, 27 May 2015 20:48:57 +0000 (22:48 +0200)]
disk/ahci.c: Add port number to port debug messages
Currently, some messages cannot be mapped to the port they belong to as
the port number is missing from the output. So add `port: n` to the
debug messages.
Toomas Soome [Thu, 16 Apr 2015 05:24:38 +0000 (08:24 +0300)]
zfs extensible_dataset and large_blocks feature support
large blocks basically use extensible dataset feature, or to be exact,
setting recordsize above 128k will trigger large_block feature to be
enabled and storing such blocks is using feature extensible dataset. so
the extensible dataset is prerequisite.
Changes implement read support extensible dataset… instead of fixed DMU
types they dont specify type, making it possible to use fat zap objects
from bonus area.
While in theory permitted by the spec, modules rarely fit in low memory
anyway and not every kernel is able to handle modules in low memory anyway.
At least VMWare is known not to be able to handle modules at arbitrary
locations.
Paul Menzel [Fri, 15 May 2015 15:35:00 +0000 (17:35 +0200)]
cb_timestamps.c: Add new time stamp descriptions
Add the descriptions of the “core”, that means no vendorcode or payload,
coreboot time stamps added up to coreboot commit a7d92441 (timestamps:
You can never have enough of them!) [1].
Running `coreboot_boottime` in the GRUB command line interface now shows
descriptions for all time stamps again on the ASRock E350M1.
Andrei Borzenkov [Sun, 17 May 2015 19:38:30 +0000 (22:38 +0300)]
bootp: ignore gateway_ip (relay) field.
From RFC1542:
The 'giaddr' field is rather poorly named. It exists to facilitate
the transfer of BOOTREQUEST messages from a client, through BOOTP
relay agents, to servers on different networks than the client.
Similarly, it facilitates the delivery of BOOTREPLY messages from the
servers, through BOOTP relay agents, back to the client. In no case
does it represent a general IP router to be used by the client. A
BOOTP client MUST set the 'giaddr' field to zero (0.0.0.0) in all
BOOTREQUEST messages it generates.
A BOOTP client MUST NOT interpret the 'giaddr' field of a BOOTREPLY
message to be the IP address of an IP router. A BOOTP client SHOULD
completely ignore the contents of the 'giaddr' field in BOOTREPLY
messages.
Leave code ifdef'd out for the time being in case we see regression.
Jan Kara [Mon, 14 Jul 2014 15:21:30 +0000 (17:21 +0200)]
xfs: Convert inode numbers to cpu endianity immediately after reading
Currently XFS driver converted inode numbers to native endianity only
when using them to compute inode position. Although this works, it is
somewhat confusing. So convert inode numbers when reading them from disk
structures as every other field.
Jan Kara [Mon, 14 Jul 2014 15:21:29 +0000 (17:21 +0200)]
xfs: Fix termination loop for directory iteration
Directory iteration used wrong position (sizeof wrong structure) for
termination of iteration inside a directory block. Luckily the position
ended up being wrong by just 1 byte and directory entries are larger so
things worked out fine in practice. But fix the problem anyway.
acpi: do not skip BIOS scan if EBDA length is zero
EBDA layout is not standardized so we cannot assume first two bytes
are length. Neither is it required by ACPI standard. HP 8710W is known
to contain zeroes here.
EDK2 network stack is based on Managed Network Protocol which is layered
on top of Simple Management Protocol and does background polling. This
polling races with grub for received (and probably trasmitted) packets
which causes either serious slowdown or complete failure to load files.
Open SNP device exclusively. This destroys all child MNP instances and
stops background polling.
Exclusive open cannot be done when enumerating cards, as it would destroy
PXE information we need to autoconfigure interface; and it cannot be done
during autoconfiguration as we need to do it for non-PXE boot as well. So
move SNP open to card ->open method and add matching ->close to clean up.
Based on patch from Mark Salter <msalter@redhat.com>
Also-By: Mark Salter <msalter@redhat.com> Closes: 41731
efinet: skip virtual IPv4 and IPv6 devices when enumerating cards
EDK2 PXE driver creates two child devices - IPv4 and IPv6 - with
bound SNP instance. This means we get three cards for every physical
adapter when enumerating. Not only is this confusing, this may result
in grub ignoring packets that come in via the "wrong" card.
Skip PXE created virtual devices when enumerating cards. Make sure to
find real card when applying initial autoconfiguration during PXE boot,
this information is associated with one of child devices.
loader/linux: do not pad initrd with zeroes at the end
Syslinux memdisk is using initrd image and needs to know uncompressed
size in advance. For gzip uncompressed size is at the end of compressed
stream. Grub padded each input file to 4 bytes at the end, which means
syslinux got wrong size.
Linux initramfs loader apparently does not care about trailing alignment.
So change code to align beginning of each file instead which atomatically
gives us the correct size for single file.
projects / thirdparty / grub.git / log
