Current critical clock list for pistachio enables
only mips and sys clocks by default but there are
also other clocks that are not claimed by anyone and
needs to be enabled by default.
This patch updates the critical clocks that need
to be enabled by default.
Add a separate struct to distinguish the critical clocks
as listed:
1.) core clocks:
a.) mips clock
2.) peripheral system clocks:
a.) sys clock
b.) sys_bus clock
c.) DDR clock
d.) ROM clock
Fixes: b35d7c33419c("CLK: Pistachio: Register core clocks") Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com> Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver") Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com> Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver") Reviewed-by: Andrew Bresitcker <abrestic@chromium.org> Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com> Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver") Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com> Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d5e136a21b2028fb1f45143ea7112d5869bfc6c7 ("clk: samsung: Register
clk provider only after registering its all clocks", merged to v3.17-rc1)
modified a way that driver registers registers to core framework. This
change has not been applied to s5pv210 clocks driver, which has been
merged in parallel to that commit. This patch adds a missing call to
samsung_clk_of_add_provider(), so the driver is operational again.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TSADC gate clock was used in Exynos4x12 DTSI for exynos-adc driver.
However TSADC is present only on Exynos4210 so on Trats2 board (with
Exynos4412 SoC) the exynos-adc driver could not be probed:
ERROR: could not get clock /adc@126C0000:adc(0)
exynos-adc 126c0000.adc: failed getting clock, err = -2
exynos-adc: probe of 126c0000.adc failed with error -2
Instead on Exynos4x12 SoCs the main clock used by Analog to Digital
Converter is located in different register and it is named in datasheet
as PCLK_ADC. Regardless of the name the purpose of this PCLK_ADC clock
is the same as purpose of TSADC from Exynos4210.
The patch adds gate clock for Exynos4x12 using the proper register so
backward compatibility is preserved. This fixes the probe of exynos-adc
driver on Exynos4x12 boards and allows accessing sensors connected to it
on Trats2 board (ntc,ncp15wb473 AP and battery thermistors).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: c63c57433003 ("ARM: dts: Add ADC's dt data to read raw data for exynos4x12") Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwmac ethernet controller on the rk3288 supports phys connected
via rgmii and rmii. With rgmii phys it is expected that the mac clock
is provided externally while with rmii phys the clock can be external
but also generated from the plls. In the later case it of course needs
be at 50MHz, which gets set from the dwmac_rk driver.
As most devices use a rgmii phy it never surfaced so far that the mac
clk mux, doesn't go up one lever to the pll clock in the rmii case with
internal clock generation, as it is missing the CLK_SET_RATE_PARENT flag,
and thus will not set the correct frequency in most cases.
Static analysis by cppcheck found an issue that was recently introduced by
commit 471f7707b6f0b1 ("PM / clock_ops: make __pm_clk_enable more generic")
where a return status in ret was not being initialised and garbage
being returned when ce->status >= PCE_STATUS_ERROR.
The fact that ret is not being checked by the caller and that
ret is only used internally __pm_clk_enable() to check if clk_enable()
was OK means we can ignore returning it instead turn
__pm_clk_enable() into function with a void return.
Fixes: 471f7707b6f0b1 ("PM / clock_ops: make __pm_clk_enable more generic") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`devpriv->ao_timer` is used while an asynchronous command is running on
the AO subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands,
`usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ao_timer` into the subdevice's
`cmd` handler, `usbduxsigma_ao_cmd()`.
Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that
`devpriv->ao_timer` did not end up less that 1, but that could not
happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had
already been range-checked.
Also note that we tested the `high_speed` variable in the old code, but
that is currently always 0 and means that we always use "scan" timing
(`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`)
and never "convert" (individual sample) timing (`cmd->scan_begin_src ==
TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`). The moved code
tests `cmd->convert_src` instead to decide whether "scan" or "convert"
timing is being used, although currently only "scan" timing is
supported.
Fixes: fb1ef622e7a3 ("staging: comedi: usbduxsigma: tidy up analog output command support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: Bernd Porr <mail@berndporr.me.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`devpriv->ai_timer` is used while an asynchronous command is running on
the AI subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands
(`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ai_timer` and
`devpriv->ai_interval` into the subdevice's `cmd` handler,
`usbduxsigma_ai_cmd()`.
Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that
`devpriv->ai_timer` did not end up less than than 1, but that could not
happen because `cmd->scan_begin_arg` had already been checked to be at
least the minimum required value (at least when `cmd->scan_begin_src ==
TRIG_TIMER`, which had also been checked to be the case).
Fixes: b986be8527c7 ("staging: comedi: usbduxsigma: tidy up analog input command support) Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: Bernd Porr <mail@berndporr.me.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432"
drivers in commits 8f567c373c4b ("staging: comedi: new adl_pci7x3x
driver") and 657f77d173d3 ("staging: comedi: remove adl_pci7230 and
adl_pci7432 drivers"). Although the new driver code agrees with the
user manuals for the respective boards, digital outputs stopped working
on the PCI-7230. This has 16 digital output channels and the previous
adl_pci7230 driver shifted the 16 bit output state left by 16 bits
before writing to the hardware register. The new adl_pci7x3x driver
doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking
for the special case of the subdevice having only 16 channels and
duplicating the 16 bit output state into both halves of the 32-bit
register. That should work both for what the board actually does and
for what the user manual says it should do.
Fixes: 8f567c373c4b ("staging: comedi: new adl_pci7x3x driver") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the various CPU_ONLINE callbacks CPUn is online but not
active. Several things can go wrong at that point, depending on
the scheduling of tasks on CPU0.
The ->wake_cpu of the unparked thread is not allowed, making a call
to select_fallback_rq() necessary. Then, select_fallback_rq() cannot
find an allowed, active CPU and promptly resets the allowed CPUs, so
that the task in question ends up on CPU0.
When those unparked tasks are eventually executed, they run
immediately into a BUG:
kernel BUG at kernel/smpboot.c:135!
Just changing the order in which the online/active bits are set
(and adding some memory barriers), would solve the two issues
above. However, it would change the order of operations back to
the one before commit 6acbfb96976f ("sched: Fix hotplug vs.
set_cpus_allowed_ptr()"), thus, reintroducing that particular
problem.
Going further back into history, we have at least the following
commits touching this topic:
- commit 2baab4e90495 ("sched: Fix select_fallback_rq() vs cpu_active/cpu_online")
- commit 5fbd036b552f ("sched: Cleanup cpu_active madness")
Together, these give us the following non-working solutions:
- secondary CPU sets active before online, because active is assumed to
be a subset of online;
- secondary CPU sets online before active, because the primary CPU
assumes that an online CPU is also active;
- secondary CPU sets online and waits for primary CPU to set active,
because it might deadlock.
Commit 875ebe940d77 ("powerpc/smp: Wait until secondaries are
active & online") introduces an arch-specific solution to this
arch-independent problem.
Now, go for a more general solution without explicit waiting and
simply set active twice: once on the secondary CPU after online
was set and once on the primary CPU after online was seen.
set_cpus_allowed_ptr()")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Anton Blanchard <anton@samba.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Joerg Roedel <jroedel@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Wilson <msw@amazon.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Link: http://lkml.kernel.org/r/1439408156-18840-1-git-send-email-jschoenh@amazon.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To iterate through the available frequencies of mma8452_hp_filter_cutoff[],
the array size of a row of that table needs to be provided to
_get_int_plus_micros_index().
Add inverse unit conversion macro to convert from standard IIO units to
units that might be used by some devices.
Those are useful in combination with scale factors that are specified as
IIO_VAL_FRACTIONAL. Typically the denominator for those specifications will
contain the maximum raw value the sensor will generate and the numerator
the value it maps to in a specific unit. Sometimes datasheets specify those
in different units than the standard IIO units (e.g. degree/s instead of
rad/s) and so we need to do a unit conversion.
From a mathematical point of view it does not make a difference whether we
apply the unit conversion to the numerator or the inverse unit conversion
to the denominator since (x / y) / z = x / (y * z). But as the denominator
is typically a larger value and we are rounding both the numerator and
denominator to integer values using the later method gives us a better
precision (E.g. the relative error is smaller if we round 8000.3 to 8000
rather than rounding 8.3 to 8).
This is where in inverse unit conversion macros will be used.
Negative return values are not supported by iio_event_poll since
its return type is unsigned int.
Fixes: f18e7a068a0a3 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The novx parameter disables the vector facility but the HWCAP_S390_VXRS
bit in the ELf hardware capabilies is always set if the machine has
the vector facility. If the user space program uses the "vx" string
in the features field of /proc/cpuinfo to utilize vector instruction
it will crash if the novx kernel paramter is set.
Convert setup_hwcaps to an arch_initcall and use MACHINE_HAS_VX to
decide if the HWCAPS_S390_VXRS bit needs to be set.
Fix a wrong logical AND (&&) used for the range check of CSR MMIO.
Spotted nicely by gcc -Wlogical-op flag:
drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’:
drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op]
Fixes: eb805623d8b1 ('drm/i915/skl: Add support to load SKL CSR firmware.') Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been many hard to track down bugs whereby userspace forgot to
flag a write buffer and then cause graphics corruption or a hung GPU
when that buffer was later purged under memory pressure (as the buffer
appeared clean, its pages would have been evicted rather than preserved
and any changes more recent than in the backing storage would be lost).
In retrospect this is a rare optimisation against memory pressure,
already the slow path. If we always mark the buffer as dirty when
accessed by the GPU, anything not used can still be evicted cheaply
(ideal behaviour for mark-and-sweep eviction) but we do not run the risk
of corruption. For correct read serialisation, userspace still has to
notify when the GPU writes to an object. However, there are certain
situations under which userspace may wish to tell white lies to the
kernel...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Kristian Høgsberg <krh@bitplanet.net> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: "Goel, Akash" <akash.goel@intel.co> Cc: Michał Winiarski <michal.winiarski@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like single link MIPI panels, similarly for dual link panels, pipe
to be configured is based on the DVO port from VBT Block 2. In hardware,
Port A is mapped with Pipe A and Port C is mapped with Pipe B.
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Commit 92122789b2d6 ("drm/i915: preserve SSC if previously set v3")
added code to intel_modeset_gem_init to override the SSC status read
from VBT with the SSC status set by BIOS.
However, intel_modeset_gem_init is invoked *after* intel_modeset_init,
which calls intel_setup_outputs, which *modifies* SSC status by way of
intel_init_pch_refclk. So unlike advertised, intel_modeset_gem_init
doesn't preserve the SSC status set by BIOS but whatever
intel_init_pch_refclk decided on.
This is a problem on dual gpu laptops such as the MacBook Pro which
require either a handler to switch DDC lines, or the discrete gpu
to proxy DDC/AUX communication: Both the handler and the discrete
gpu may initialize after the i915 driver, and consequently, an LVDS
connector may initially seem disconnected and the SSC therefore
is disabled by intel_init_pch_refclk, but on reprobe the connector
may turn out to be connected and the SSC must then be enabled.
Due to 92122789b2d6 however, the SSC is not enabled on reprobe since
it is assumed BIOS disabled it while in fact it was disabled by
intel_init_pch_refclk.
Also, because the SSC status is preserved so late, the preserved value
only ever gets used on resume but not on panel initialization:
intel_modeset_init calls intel_init_display which indirectly calls
intel_panel_use_ssc via multiple subroutines, *before* the BIOS value
overrides the VBT value in intel_modeset_gem_init (intel_panel_use_ssc
is the sole user of dev_priv->vbt.lvds_use_ssc).
Fix this by moving the code introduced by 92122789b2d6 from
intel_modeset_gem_init to intel_modeset_init before the invocation
of intel_setup_outputs and intel_init_display.
Add a DRM_DEBUG_KMS as suggested way back by Jani:
http://lists.freedesktop.org/archives/intel-gfx/2014-June/046666.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115 Tested-by: Paul Hordiienko <pvt.gord@gmail.com>
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina] Tested-by: William Brown <william@blackhats.net.au>
[MBP 8,2 2011 intel SNB + amd turks pre-retina] Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina] Tested-by: Bruno Bierbaumer <bruno@bierbaumer.net>
[MBP 11,3 2013 intel HSW + nvidia GK107 retina -- work in progress] Fixes: 92122789b2d6 ("drm/i915: preserve SSC if previously set v3") Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function 'amdgpu_uvd_cs_pass2':
warning: 'min_ctx_size' may be used uninitialized in this function
buf_sizes[0x4] = min_ctx_size;
^
note: 'min_ctx_size' was declared here
unsigned image_size, tmp, min_dpb_size, num_dpb_buffer, min_ctx_size;
^ Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Port of:
drm/radeon/atom: Send out the full AUX address
to radeon non-atom aux path
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are no longer checkling the DP link status on long hpd. We used to do
that from the .hot_plug() handler, but it was removed when MST got
introduced.
If there's no userspace we now fail to retrain the link if the sink
power is toggled (or cable yanked and replugged), meaning the user is
left staring at a blank screen. With the retraining put back that should
be fixed.
Also remove the leftover comment that referred to the old retraining
from .hot_plug().
drm/i915: gen4: work around hang during hibernation
using an explicit blacklist for the GENs/BIOS vendors where the issue was
reported. Later there we had reports of the same failure on platforms not on
this list.
To my best knowledge the correct thing to do is still to put the device to PCI
D3 state during hibernation, see [1] and [2] for the reasons. This also aligns
with our future plans to unify more the runtime and system suspend/resume
paths. Since an exact blacklist seems to be impractical (multiple GENs and
BIOS vendors are affected) apply the workaround on everything pre GEN6.
Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:
- GPU has only one monitor connected. It's connected via
DisplayPort, and does not go through an adaptor of any sort.
- User unplugs DisplayPort connector from GPU.
- Change in HPD is detected by the driver, we probe every
DisplayPort for a possible connection.
- Probe the port the user originally had the monitor connected
on for it's dpcd. This fails, and we clear the first (and only
the first) byte of the dpcd to indicate we no longer have a
dpcd for this port.
- User plugs the previously disconnected monitor back into the
same DisplayPort.
- radeon_connector_hotplug() is called before everyone else,
and tries to handle the link training. Since only the first
byte of the dpcd is zeroed, the driver is able to complete
link training but does so against the wrong dpcd, causing it
to initialize the link with the wrong settings.
- Display stays blank (usually), dpcd is probed after the
initial link training, and the driver prints no obvious
messages to the log.
In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javi Merino [Tue, 25 Aug 2015 18:22:35 +0000 (19:22 +0100)]
thermal: power_allocator: allocate with kcalloc what you free with kfree
Commit cf736ea6f902 ("thermal: power_allocator: do not use devm*
interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but
it's corresponding devm_kfree() was changed to kfree(). Allocate with
kcalloc() to match the kfree().
Fixes: cf736ea6f902 ("thermal: power_allocator: do not use devm* interfaces") Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Javi Merino <javi.merino@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 28 Aug 2015 18:42:00 +0000 (11:42 -0700)]
Merge tag 'sound-fix-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are stable fixes that have been gathered since rc8: fixes for
HD-audio widget power control regressions since 4.1, a NULL fix for
HD-audio HDMI, a noise fix for Conexant codecs and a quirk addition
for USB-Audio DSD"
* tag 'sound-fix-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix path power activation
ALSA: hda - Check all inputs for is_active_nid_for_any()
ALSA: hda: fix possible NULL dereference
ALSA: hda - Shutdown CX20722 on reboot/free to avoid spurious noises
ALSA: usb: Add native DSD support for Gustard DAC-X20U
Linus Torvalds [Fri, 28 Aug 2015 00:59:17 +0000 (17:59 -0700)]
Merge tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix MSI/MSI-X on pseries from Guilherme"
* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
Pull networking fixes from David Miller:
"Some straggler bug fixes here:
1) Netlink_sendmsg() doesn't check iterator type properly in mmap
case, from Ken-ichirou MATSUZAWA.
2) Don't sleep in atomic context in bcmgenet driver, from Florian
Fainelli.
3) The pfkey_broadcast() code patch can't actually ever use anything
other than GFP_ATOMIC. And the cases that right now pass
GFP_KERNEL or similar will currently trigger an RCU splat. Just
use GFP_ATOMIC unconditionally. From David Ahern.
4) Fix FD bit timings handling in pcan_usb driver, from Marc
Kleine-Budde.
5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.
6) Traversal into drivers/net/ethernet/renesas should be triggered by
CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
option. From Kazuya Mizuguchi.
7) Fix regression in handling of igmp_join errors in vxlan, from
Marcelo Ricardo Leitner.
8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
mutex when programming the registers. From Russell King.
9) Fix non-forced handling in u32_destroy(), from WANG Cong.
10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
usbnet_stop(), from Eugene Shatokhin.
11) In sfc driver, don't fetch statistics firmware isn't capable of,
from Bert Kenward.
12) Verify ASCONF address parameter location in SCTP, from Xin Long"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
sctp: asconf's process should verify address parameter is in the beginning
sfc: only use vadaptor stats if firmware is capable
net: phy: fixed: propagate fixed link values to struct
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
drivers: net: xgene: fix: Oops in linkwatch_fire_event
cls_u32: complete the check for non-forced case in u32_destroy()
net: fec: use reinit_completion() in mdio accessor functions
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
vxlan: re-ignore EADDRINUSE from igmp_join
net: compile renesas directory if NET_VENDOR_RENESAS is configured
ip6_gre: release cached dst on tunnel removal
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
net: Fix RCU splat in af_key
net: bcmgenet: fix uncleaned dma flags
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
netlink: mmap: fix tx type check
Linus Torvalds [Fri, 28 Aug 2015 00:46:06 +0000 (17:46 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
lucien [Wed, 26 Aug 2015 20:52:20 +0000 (04:52 +0800)]
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count. This allowed the association
to better enforce assoc.max_retrans limit.
However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state. In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.
This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING. As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.
Fixes: Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Thu, 27 Aug 2015 08:26:34 +0000 (16:26 +0800)]
sctp: asconf's process should verify address parameter is in the beginning
in sctp_process_asconf(), we get address parameter from the beginning of
the addip params. but we never check if it's really there. if the addr
param is not there, it still can pass sctp_verify_asconf(), then to be
handled by sctp_process_asconf(), it will not be safe.
so add a code in sctp_verify_asconf() to check the address parameter is in
the beginning, or return false to send abort.
note that this can also detect multiple address parameters, and reject it.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Toshi Kani [Wed, 26 Aug 2015 16:20:23 +0000 (10:20 -0600)]
nfit: Clarify memory device state flags strings
ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows. These bits indicate multiple info,
such as failures, pending event, and capability.
Bit [0] set to 1 to indicate that the previous SAVE to the
Memory Device failed.
Bit [1] set to 1 to indicate that the last RESTORE from the
Memory Device failed.
Bit [2] set to 1 to indicate that platform flush of data to
Memory Device failed. As a result, the restored data content
may be inconsistent even if SAVE and RESTORE do not indicate
failure.
Bit [3] set to 1 to indicate that the Memory Device is observed
to be not armed prior to OSPM hand off. A Memory Device is
considered armed if it is able to accept persistent writes.
Bit [4] set to 1 to indicate that the Memory Device observed
SMART and health events prior to OSPM handoff.
/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.
Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: Robert Elliott <elliott@hp.com> Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed'] Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now] Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Bert Kenward [Wed, 26 Aug 2015 15:39:03 +0000 (16:39 +0100)]
sfc: only use vadaptor stats if firmware is capable
Some of the stats handling code differs based on SR-IOV support,
and SRIOV support is only available if full-featured firmware is
used.
Do not use vadaptor stats if firmware mode is not set to
full-featured.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 26 Aug 2015 14:58:47 +0000 (17:58 +0300)]
net: phy: fixed: propagate fixed link values to struct
The fixed link values parsed from the device tree are stored in
the struct fixed_phy member status. The struct phy_device members
speed, duplex were not updated.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Aug 2015 18:12:41 +0000 (11:12 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull amr64 kvm fix from Will Deacon:
"We've uncovered a nasty bug in the arm64 KVM code which allows a badly
behaved 32-bit guest to bring down the host. The fix is simple (it's
what I believe we call a "brown paper bag" bug) and I don't think it
makes sense to sit on this, particularly as Russell ended up
triggering this rather than just somebody noticing a potential problem
by inspection.
Usually arm64 KVM changes would go via Paolo's tree, but he's on
holiday at the moment and the deal is that anything urgent gets
shuffled via the arch trees, so here it is.
Summary:
Fix arm64 KVM issue when injecting an abort into a 32-bit guest, which
would lead to an illegal exception return at EL2 and a subsequent host
crash"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: KVM: Fix host crash when injecting a fault into a 32bit guest
Marc Zyngier [Thu, 27 Aug 2015 15:10:01 +0000 (16:10 +0100)]
arm64: KVM: Fix host crash when injecting a fault into a 32bit guest
When injecting a fault into a misbehaving 32bit guest, it seems
rather idiotic to also inject a 64bit fault that is only going
to corrupt the guest state. This leads to a situation where we
perform an illegal exception return at EL2 causing the host
to crash instead of killing the guest.
Just fix the stupid bug that has been there from day 1.
Cc: <stable@vger.kernel.org> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Linus Torvalds [Wed, 26 Aug 2015 18:08:47 +0000 (11:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two fixes in this pull request:
- The writeback regression fix from Tejun, which has been weeks in
the making. This fixes a case where we would sometimes not issue
writeback when we should have.
- An older fix for a memory corruption issue in mtip32xx. It was
deferred since we wanted a better fix for this (driver should not
have to handle that case), but given the timing, it's better to put
the simple fix in for 4.2 release"
* 'for-linus' of git://git.kernel.dk/linux-block:
mtip32x: fix regression introduced by blk-mq per-hctx flush
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
Add factory recertified Crucial M500s to blacklist
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
Since commit 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.
This exhibits as drivers not being able to enable MSI, eg:
bnx2x 0000:01:00.0: no msix capability found
This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.
Fixes: 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment] Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
Commit 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap] Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Eugene Shatokhin [Mon, 24 Aug 2015 20:13:42 +0000 (23:13 +0300)]
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 26 Aug 2015 00:26:00 +0000 (17:26 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fix from Dan Williams:
"A single fix for status register read size in the nd_blk driver.
The effect of getting the width of this register read wrong is that
all I/O fails when the read returns non-zero. Given the availability
of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
in during the 4.3 merge window with a tag for 4.2-stable. Otherwise,
this makes the 4.2 kernel fully functional with devices that conform
to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
Firmware Interface Table)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, nd_blk: BLK status register is only 32 bits
WANG Cong [Tue, 25 Aug 2015 23:38:12 +0000 (16:38 -0700)]
cls_u32: complete the check for non-forced case in u32_destroy()
In commit 1e052be69d04 ("net_sched: destroy proto tp when all filters are gone")
I added a check in u32_destroy() to see if all real filters are gone
for each tp, however, that is only done for root_ht, same is needed
for others.
This can be reproduced by the following tc commands:
tc filter add dev eth0 parent 1:0 prio 5 handle 15: protocol ip u32 divisor 256
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:2 u32
ht 15:2: match ip src 10.0.0.2 flowid 1:10
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:3 u32
ht 15:2: match ip src 10.0.0.3 flowid 1:10
Fixes: 1e052be69d04 ("net_sched: destroy proto tp when all filters are gone") Reported-by: Akshat Kakkar <akshat.1984@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich [Mon, 24 Aug 2015 12:22:25 +0000 (06:22 -0600)]
LSM: restore certain default error codes
While in most cases commit b1d9e6b064 ("LSM: Switch to lists of hooks")
retained previous error returns, in three cases it altered them without
any explanation in the commit message. Restore all of them - in the
security_old_inode_init_security() case this led to reiserfs using
uninitialized data, sooner or later crashing the system (the only other
user of this function - ocfs2 - was unaffected afaict, since it passes
pre-initialized structures).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Russell King [Tue, 25 Aug 2015 08:49:53 +0000 (09:49 +0100)]
net: fec: use reinit_completion() in mdio accessor functions
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 25 Aug 2015 08:49:47 +0000 (09:49 +0100)]
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.
This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.
Fixes: a59a4d192 ("phy: add the EEE support and the way to access to the MMD registers.") Fixes: 0c1d77dfb ("net: libphy: Add phy specific function to access mmd phy registers") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before 56ef9c909b40[1] it used to ignore all errors from igmp_join().
That commit enhanced that and made it error out whatever error happened
with igmp_join(), but that's not good because when using multicast
groups vxlan will try to join it multiple times if the socket is reused
and then the 2nd and further attempts will fail with EADDRINUSE.
As we don't track to which groups the socket is already subscribed, it's
okay to just ignore that error.
Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope") Reported-by: John Nielsen <lists@jnielsen.net> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Aug 2015 23:12:45 +0000 (16:12 -0700)]
Merge tag 'linux-can-fixes-for-4.2-20150825' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is the updated pull request of one patch by me for the peak_usb
driver. It fixes the driver, so that non FD adapters don't provide CAN
FD bittimings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kazuya Mizuguchi [Tue, 25 Aug 2015 08:03:20 +0000 (18:03 +1000)]
net: compile renesas directory if NET_VENDOR_RENESAS is configured
Currently the renesas ethernet driver directory is compiled if SH_ETH is
configured rather than NET_VENDOR_RENESAS. Although incorrect that was
quite harmless as until recently as SH_ETH configured the only driver in
the renesas directory. However, as of c156633f1353 ("Renesas Ethernet AVB
driver proper") the renesas directory includes another driver, configured
by RAVB, and it makes little sense for it to have a hidden dependency on
SH_ETH.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[horms: rewrote changelog] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
huaibin Wang [Tue, 25 Aug 2015 14:20:34 +0000 (16:20 +0200)]
ip6_gre: release cached dst on tunnel removal
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
CC: Dmitry Kozlov <xeb@mail.ru> Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: huaibin Wang <huaibin.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Moyer [Wed, 29 Jul 2015 14:22:50 +0000 (10:22 -0400)]
mtip32x: fix regression introduced by blk-mq per-hctx flush
Hi,
After commit f70ced091707 (blk-mq: support per-distpatch_queue flush
machinery), the mtip32xx driver may oops upon module load due to walking
off the end of an array in mtip_init_cmd. On initialization of the
flush_rq, init_request is called with request_index >= the maximum queue
depth the driver supports. For mtip32xx, this value is used to index
into an array. What this means is that the driver will walk off the end
of the array, and either oops or cause random memory corruption.
The problem is easily reproduced by doing modprobe/rmmod of the mtip32xx
driver in a loop. I can typically reproduce the problem in about 30
seconds.
Now, in the case of mtip32xx, it actually doesn't support flush/fua, so
I think we can simply return without doing anything. In addition, no
other mq-enabled driver does anything with the request_index passed into
init_request(), so no other driver is affected. However, I'm not really
sure what is expected of drivers. Ming, what did you envision drivers
would do when initializing the flush requests?
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Tejun Heo [Tue, 25 Aug 2015 18:11:52 +0000 (14:11 -0400)]
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
e79729123f63 ("writeback: don't issue wb_writeback_work if clean")
updated writeback path to avoid kicking writeback work items if there
are no inodes to be written out; unfortunately, the avoidance logic
was too aggressive and broke sync_inodes_sb().
* sync_inodes_sb() must write out I_DIRTY_TIME inodes but I_DIRTY_TIME
inodes dont't contribute to bdi/wb_has_dirty_io() tests and were
being skipped over.
* inodes are taken off wb->b_dirty/io/more_io lists after writeback
starts on them. sync_inodes_sb() skipping wait_sb_inodes() when
bdi_has_dirty_io() breaks it by making it return while writebacks
are in-flight.
This patch fixes the breakages by
* Removing bdi_has_dirty_io() shortcut from bdi_split_work_to_wbs().
The callers are already testing the condition.
* Removing bdi_has_dirty_io() shortcut from sync_inodes_sb() so that
it always calls into bdi_split_work_to_wbs() and wait_sb_inodes().
* Making bdi_split_work_to_wbs() consider the b_dirty_time list for
WB_SYNC_ALL writebacks.
Kudos to Eryu, Dave and Jan for tracking down the issue.
Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: e79729123f63 ("writeback: don't issue wb_writeback_work if clean") Link: http://lkml.kernel.org/g/20150812101204.GE17933@dhcp-13-216.nay.redhat.com Reported-and-bisected-by: Eryu Guan <eguan@redhat.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.com> Cc: Ted Ts'o <tytso@google.com> Signed-off-by: Jens Axboe <axboe@fb.com>
David Daney [Fri, 21 Aug 2015 23:16:03 +0000 (16:16 -0700)]
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
commit 18ee49ddb0d2 ("phylib: rename mii_bus::dev to mii_bus::parent")
changed the parent of PHY devices from the bus to the bus parent.
Then, commit 4dea547fef1b ("phylib: rework to prepare for OF
registration of PHYs") moved the code into phy_device.c
At this point, it is somewhat unclear why the change was seen as
necessary. But, when we look at the device model tree in
/sys/devices, it is clearly incorrect. The PHYs should be children of
their MDIO bus.
Change the PHY's parent device to be the MDIO bus device.
Cc: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Daney <david.daney@cavium.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 25 Aug 2015 16:01:05 +0000 (09:01 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for a APIC regression introduced in 4.0 which went
undetected until now.
I screwed up the x2apic cleanup in a subtle way. The screwup is only
visible on systems which have x2apic preenabled in the BIOS and need
to disable it during boot"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix fallout from x2apic cleanup
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
The CAN FD data bittiming constants are provided via netlink only when there
are valid CAN FD constants available in priv->data_bittiming_const.
Due to the indirection of pointer assignments in the peak_usb driver the
priv->data_bittiming_const never becomes NULL - not even for non-FD adapters.
The data_bittiming_const points to zero'ed data which leads to this result
when running 'ip -details link show can0':
35: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state STOPPED restart-ms 0
pcan_usb: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
: dtseg1 0..0 dtseg2 0..0 dsjw 1..0 dbrp 0..0 dbrp-inc 0 <== BROKEN!
clock 8000000
This patch changes the struct peak_usb_adapter::bittiming_const and struct
peak_usb_adapter::data_bittiming_const to pointers to fix the assignemnt
problems.
Cc: linux-stable <stable@vger.kernel.org> # >= 4.0 Reported-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Takashi Iwai [Mon, 24 Aug 2015 08:52:06 +0000 (10:52 +0200)]
ALSA: hda - Fix path power activation
The widget power-saving code tries to turn up/down the power of each
widget in the I/O paths that are modified at each jack plug/unplug.
The recent report revealed that the power activation leaves some
widgets unpowered after plugging. This is because
snd_hda_activate_path() turns on path->active flag at the end of the
function while the path power management is done before that. Then
it's regarded as if nothing is active, and the driver turns off the
power.
The fix is simply to set the flag at the beginning of the function,
before trying to power up.
Takashi Iwai [Mon, 24 Aug 2015 08:45:27 +0000 (10:45 +0200)]
ALSA: hda - Check all inputs for is_active_nid_for_any()
The is_active_nid_for_any() function in the generic parser is supposed
to check all connections from/to the given widget, but the current
code checks only the first input connection (index = 0).
This patch corrects the code to check all inputs by passing -1 to
index argument.
J. Bruce Fields [Mon, 24 Aug 2015 20:44:40 +0000 (16:44 -0400)]
nfsd: Add Jeff Layton as co-maintainer
Jeff has been doing a lot of development (including much of the
state-locking rewrite just as one example) plus lots of review and other
miscellaneous nfsd work, so let's acknowledge the status quo.
I'll continue to be the one to send regular pull requests but Jeff will
should be available to cover there occasionally too.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In pfkey_sendmsg the net mutex is taken and then pfkey_broadcast takes
the RCU lock.
Since pfkey_broadcast takes the RCU lock the allocation argument is
pointless since GFP_ATOMIC must be used between the rcu_read_{,un}lock.
The one call outside of rcu can be done with GFP_KERNEL.
Fixes: 7f6b9dbd5afbd ("af_key: locking change") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Osterhoff [Mon, 24 Aug 2015 12:11:39 +0000 (14:11 +0200)]
ALSA: hda: fix possible NULL dereference
After a for-loop was replaced by list_for_each_entry, see
Commit bbbc7e8502c9 ("ALSA: hda - Allocate hda_pcm objects dynamically"),
Commit 751e2216899c ("ALSA: hda: fix possible null dereference"),
a possible NULL pointer dereference has been introduced; this patch adds
the NULL check on pcm->pcm, while leaving a potentially superfluous
check on pcm itself untouched.
Jaedon Shin [Fri, 21 Aug 2015 01:08:26 +0000 (10:08 +0900)]
net: bcmgenet: fix uncleaned dma flags
Clean the dma flags of multiq ring buffer int the interface stop
process. This patch fixes that the genet is not running while the
interface is re-enabled.
$ ifup eth0 - running after booting
$ ifdown eth0
$ ifup eth0 - not running and occur tx_timeout
The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag
only. If the genet has multiq, the dma register is not cleaned. and
bcmgenet_init_dma() is not done correctly. in case
GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running
bcmgenet_dma_disable().
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 21 Aug 2015 01:04:22 +0000 (18:04 -0700)]
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
bcmgenet_timeout() executes in atomic context, yet we will invoke
napi_disable() which does sleep. Looking back at the changes, disabling
TX napi and re-enabling it is completely useless, since we reclaim all
TX buffers and re-enable interrupts, and wake up the TX queues.
Fixes: 13ea657806cf ("net: bcmgenet: improve TX timeout") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 24 Aug 2015 03:46:22 +0000 (20:46 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of major (hang and deadlock) fixes with fortunately fairly
rare triggering conditions. The PM oops is only really triggered by
people using enclosure services (rare) and the fnic driver is mostly
used in enterprise environments"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: Fix NULL pointer dereference in runtime PM
fnic: Use the local variable instead of I/O flag to acquire io_req_lock in fnic_queuecommand() to avoid deadloack
Linus Torvalds [Sun, 23 Aug 2015 14:23:09 +0000 (07:23 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS bug fixes from Ralf Baechle:
"Two more fixes for 4.2.
One fixes a build issue with the LLVM assembler - LLVM assembler macro
names are case sensitive, GNU as macro names are insensitive; the
other corrects a license string (GPL v2, not GPLv2) such that the
module loader will recognice the license correctly"
Vincent Bernat [Sat, 15 Aug 2015 13:49:13 +0000 (15:49 +0200)]
9p: ensure err is initialized to 0 in p9_client_read/write
Some use of those functions were providing unitialized values to those
functions. Notably, when reading 0 bytes from an empty file on a 9P
filesystem, the return code of read() was not 0.
Linus Torvalds [Sat, 22 Aug 2015 22:48:04 +0000 (15:48 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another couple of small ARM fixes.
A patch from Masahiro Yamada who noticed that "make -jN all zImage"
would end up generating bad images where N > 1, and a patch from
Nicolas to fix the Marvell CPU user access optimisation code when page
faults are disabled"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8418/1: add boot image dependencies to not generate invalid images
ARM: 8414/1: __copy_to_user_memcpy: fix mmap semaphore usage
Linus Torvalds [Sat, 22 Aug 2015 15:15:36 +0000 (08:15 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Various low level fixes: fix more fallout from the FPU rework and the
asm entry code rework, plus an MSI rework fix, and an idle-tracing fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/math-emu: Fix crash in fork()
x86/fpu/math-emu: Fix math-emu boot crash
x86/idle: Restore trace_cpu_idle to mwait_idle() calls
x86/irq: Build correct vector mapping for multiple MSI interrupts
Revert "sched/x86_64: Don't save flags on context switch"
Linus Torvalds [Sat, 22 Aug 2015 15:06:28 +0000 (08:06 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes: a 'perf record' deadlock fix plus debuggability fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Show backtrace when handling a SIGSEGV on --stdio mode
perf tools: Fix buildid processing
perf tools: Make fork event processing more resilient
perf tools: Avoid deadlock when map_groups are broken
Thomas Gleixner [Sat, 22 Aug 2015 14:41:17 +0000 (16:41 +0200)]
x86/apic: Fix fallout from x2apic cleanup
In the recent x2apic cleanup I got two things really wrong:
1) The safety check in __disable_x2apic which allows the function to
be called unconditionally is backwards. The check is there to
prevent access to the apic MSR in case that the machine has no
apic. Though right now it returns if the machine has an apic and
therefor the disabling of x2apic is never invoked.
2) x2apic_disable() sets x2apic_mode to 0 after registering the local
apic. That's wrong, because register_lapic_address() checks x2apic
mode and therefor takes the wrong code path.
This results in boot failures on machines with x2apic preenabled by
BIOS and can also lead to an fatal MSR access on machines without
apic.
The solutions are simple:
1) Correct the sanity check for apic availability
2) Clear x2apic_mode _before_ calling register_lapic_address()
Fixes: 659006bf3ae3 'x86/x2apic: Split enable and setup function' Reported-and-tested-by: Javier Monteagudo <javiermon@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://bugzilla.redhat.com/show_bug.cgi?id=1224764 Cc: stable@vger.kernel.org # 4.0+ Cc: Laura Abbott <labbott@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Borislav Petkov <bp@alien8.de>
Linus Torvalds [Sat, 22 Aug 2015 14:45:36 +0000 (07:45 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Linus Torvalds [Sat, 22 Aug 2015 14:37:41 +0000 (07:37 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two minimalistic fixes for 4.2 regressions:
- Eric fixed a thinko in the timer_list base switching code caused by
the overhaul of the timer wheel. It can cause a cpu to see the
wrong base for a timer while we move the timer around.
- Guenter fixed a regression for IMX if booted w/o device tree, where
the timer interrupt is not initialized and therefor the machine
fails to boot"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/imx: Fix boot with non-DT systems
timer: Write timer->flags atomically
b1276c48e91b ("x86/fpu: Initialize fpregs in fpu__init_cpu_generic()")
I failed to consider math-emu's limitation that it cannot execute the
FNINIT instruction in kernel mode.
The long term fix might be to allow math-emu to execute (certain) kernel
mode FPU instructions, but for now apply the safe (albeit somewhat ugly)
fix: initialize the emulation state explicitly without trapping out to
the FPU emulator.
Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
While the idea behind get_maintainer seems highly useful it's
unfortunately way to trigger happy to grab people that once had a few
commits to files. For someone like me who does a lot of tree-wide API
work that leads to an incredible amount of Cc spam.
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 21 Aug 2015 21:11:51 +0000 (14:11 -0700)]
mm: make page pfmemalloc check more robust
Commit c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub] Fixes: c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") Signed-off-by: Michal Hocko <mhocko@suse.com> Debugged-by: Vlastimil Babka <vbabka@suse.com> Debugged-by: Jiri Bohac <jbohac@suse.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Miller <davem@davemloft.net> Acked-by: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [3.6+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 21 Aug 2015 18:18:10 +0000 (11:18 -0700)]
Merge tag 'pci-v4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for ASPM-related NULL pointer dereference crashes on
Sparc and PowerPC and 64-bit PCI address-related HPMC crashes on
PA-RISC. These are both caused by things we merged in the v4.2 merge
window. Details:
Resource management
- Don't use 64-bit bus addresses on PA-RISC
Miscellaneous
- Tolerate hierarchies with no Root Port"
* tag 'pci-v4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't use 64-bit bus addresses on PA-RISC
PCI: Tolerate hierarchies with no Root Port
projects / thirdparty / kernel / stable.git / log
