Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Support for termiox was added by commit 1d65b4a088de ("tty: Add
termiox") in 2008 but no driver support ever followed and it was
recently ripped out by commit e0efb3168d34 ("tty: Remove dead termiox
code").
Fix the return value for the unsupported termiox ioctls, which have
always returned -EINVAL, by explicitly returning -ENOTTY rather than
removing them completely and falling back to the default unrecognised-
ioctl handling.
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e667 ("USB: allow users to run setserial with cdc-acm") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db0a ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Li <wangli74@huawei.com> Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.
The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.
So let's switch to hardware dummy cycles transfer to fix this issue.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 -- 4 % complete
(Press Ctrl+C)
[ 169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.603480] spi-nor spi0.0: Erase operation failed.
[ 173.608368] spi-nor spi0.0: Attempted to modify a protected sector.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When current CPU load is not L0 then loading armada-37xx-cpufreq.ko driver
fails with following error:
# modprobe armada-37xx-cpufreq
[ 502.702097] Unsupported CPU frequency 250 MHz
This issue was partially fixed by commit 8db82563451f ("cpufreq:
armada-37xx: fix frequency calculation for opp"), but only for calculating
CPU frequency for opp.
Fix this also for determination of base CPU frequency.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for
opp") changed calculation of frequency passed to the dev_pm_opp_add()
function call. But the code for dev_pm_opp_remove() function call was not
updated, so the driver cleanup phase does not work when registration fails.
This fixes the issue by using the same frequency in both calls.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for opp") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CPU frequency is at 250 MHz and set_rate() is called with 500 MHz (L1)
quickly followed by a call with 1 GHz (L0), the CPU does not necessarily
stay in L1 for at least 20ms as is required by Marvell errata.
This situation happens frequently with the ondemand cpufreq governor and
can be also reproduced with userspace governor. In most cases it causes CPU
to crash.
This change fixes the above issue and ensures that the CPU always stays in
L1 for at least 20ms when switching from any state to L0.
Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 61c40f35f5cd ("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that the workaround introduced by commit 61c40f35f5cd
("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to
1.2GHz") when base CPU frequency is 1.2 GHz is also required when base
CPU frequency is 1 GHz. Otherwise switching CPU frequency directly from
L2 (250 MHz) to L0 (1 GHz) causes a crash.
When base CPU frequency is just 800 MHz no crashed were observed during
switch from L2 to L0.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original CPU voltage value for load L1 is too low for Armada 37xx SoC
when base CPU frequency is 1000 or 1200 MHz. It leads to instabilities
where CPU gets stuck soon after dynamic voltage scaling from load L1 to L0.
Update the CPU voltage value for load L1 accordingly when base frequency is
1000 or 1200 MHz. The minimal L1 value for base CPU frequency 1000 MHz is
updated from the original 1.05V to 1.108V and for 1200 MHz is updated to
1.155V. This minimal L1 value is used only in the case when it is lower
than value for L0.
This change fixes CPU instability issues on 1 GHz and 1.2 GHz variants of
Espressobin and 1 GHz Turris Mox.
Marvell previously for 1 GHz variant of Espressobin provided a patch [1]
suitable only for their Marvell Linux kernel 4.4 fork which workarounded
this issue. Patch forced CPU voltage value to 1.108V in all loads. But
such change does not fix CPU instability issues on 1.2 GHz variants of
Armada 3720 SoC.
During testing we come to the conclusion that using 1.108V as minimal
value for L1 load makes 1 GHz variants of Espressobin and Turris Mox boards
stable. And similarly 1.155V for 1.2 GHz variant of Espressobin.
These two values 1.108V and 1.155V are documented in Armada 3700 Hardware
Specifications as typical initial CPU voltage values.
Discussion about this issue is also at the Armbian forum [2].
This method was supposed to be needed by the armada-37xx-cpufreq driver,
but was never actually called due to wrong assumptions in the cpufreq
driver. After this was fixed in the cpufreq driver, this method is not
needed anymore.
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CPU frequency determining software [1] we have discovered that
after this driver does one CPU frequency change, the base frequency of
the CPU is set to the frequency of TBG-A-P clock, instead of the TBG
that is parent to the CPU.
This can be reproduced on EspressoBIN and Turris MOX:
cd /sys/devices/system/cpu/cpufreq/policy0
echo powersave >scaling_governor
echo performance >scaling_governor
Running the mhz tool before this driver is loaded reports 1000 MHz, and
after loading the driver and executing commands above the tool reports
800 MHz.
The change of TBG clock selector is supposed to happen in function
armada37xx_cpufreq_dvfs_setup. Before the function returns, it does
this:
parent = clk_get_parent(clk);
clk_set_parent(clk, parent);
The armada-37xx-periph clock driver has the .set_parent method
implemented correctly for this, so if the method was actually called,
this would work. But since the introduction of the common clock
framework in commit b2476490ef11 ("clk: introduce the common clock..."),
the clk_set_parent function checks whether the parent is actually
changing, and if the requested new parent is same as the old parent
(which is obviously the case for the code above), the .set_parent method
is not called at all.
This patch fixes this issue by filling the correct TBG clock selector
directly in the armada37xx_cpufreq_dvfs_setup during the filling of
other registers at the same address. But the determination of CPU TBG
index cannot be done via the common clock framework, therefore we need
to access the North Bridge Peripheral Clock registers directly in this
driver.
[1] https://github.com/wtarreau/mhz
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
As far as I can tell, the only difference between 'struct cppc_attr'
and 'struct kobj_attribute' aside from the type of the attr parameter
is the type of the count parameter in the ->store() member (ssize_t vs.
size_t), which does not actually matter because all of these nodes are
read-only.
Eliminate 'struct cppc_attr' in favor of 'struct kobj_attribute' to fix
the violation.
When CONFIG_ARM_QCOM_SPM_CPUIDLE is y and CONFIG_MMU is not set,
compiling errors are encountered as follows:
drivers/cpuidle/cpuidle-qcom-spm.o: In function `spm_dev_probe':
cpuidle-qcom-spm.c:(.text+0x140): undefined reference to `cpu_resume_arm'
cpuidle-qcom-spm.c:(.text+0x148): undefined reference to `cpu_resume_arm'
Note that cpu_resume_arm is defined when MMU is set. So, add dependency
on MMU in ARM_QCOM_SPM_CPUIDLE configuration.
Fixes: a871be6b8eee ("cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: He Ying <heying24@huawei.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210406123328.92904-1-heying24@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that no validation of how much data the firmware loader read in
for a given segment truncated segment files would best case result in a
hash verification failure, without any indication of what went wrong.
Improve this by validating that the firmware loader did return the
amount of data requested.
The code validates that segments of p_memsz bytes of a segment will fit
in the provided memory region, but does not validate that p_filesz bytes
will, which means that an incorrectly crafted ELF header might write
beyond the provided memory region.
Fixes: 051fb70fd4ea ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Reviewed-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20210107233119.717173-1-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a5c ("spi: Introduce device-managed SPI controller allocation") Signed-off-by: William A. Kennington III <wak@google.com> Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: ca7b72b5a5f2 ("clocksource: Add driver for the Ingenic JZ47xx OST") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210308123031.2285083-1-weiyongjun1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid spurious timer interrupts when KTIME_MAX is used, we need to
configure set_state_oneshot_stopped(). Although implementing this is
optional, it still affects things like power management for the extra
timer interrupt.
For more information, please see commit 8fff52fd5093 ("clockevents:
Introduce CLOCK_EVT_STATE_ONESHOT_STOPPED state") and commit cf8c5009ee37
("clockevents/drivers/arm_arch_timer: Implement
->set_state_oneshot_stopped()").
Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210304072135.52712-4-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the timer is configured in posted mode, we need to check the write-
posted status register (TWPS) before writing to the register.
We now check TWPS after the write starting with commit 52762fbd1c47
("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource
support").
For example, in the TRM for am571x the following is documented in chapter
"22.2.4.13.1.1 Write Posting Synchronization Mode":
"For each register, a status bit is provided in the timer write-posted
status (TWPS) register. In this mode, it is mandatory that software check
this status bit before any write access. If a write is attempted to a
register with a previous access pending, the previous access is discarded
without notice."
The regression happened when I updated the code to use standard read/write
accessors for the driver instead of using __omap_dm_timer_load_start().
We have__omap_dm_timer_load_start() check the TWPS status correctly using
__omap_dm_timer_write().
Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210304072135.52712-2-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Make init_bios_attributes() ACPI object parsing more robust:
1. Always check that the type of the return ACPI object is package, rather
then only checking this for instance_id == 0
2. Check that the package has the minimum amount of elements which will
be consumed by the populate_foo_data() for the attr_type
Note/TODO: The populate_foo_data() functions should also be made more
robust. The should check the type of each of the elements matches the
type which they expect and in case of populate_enum_data()
obj->package.count should be passed to it as an argument and it should
re-check this itself since it consume a variable number of elements.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321121607.35717-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the greybus implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: e68453ed28c5 ("greybus: uart-gb: now builds, more framework added") Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210407102334.32361-7-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Fix the fwserial implementation by dropping its custom interpretation of
the unused xmit_fifo_size field, which was overflowed with the driver
FIFO size. Also leave the type and flags fields unset as these cannot be
changed.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
closing_wait, but let's report back the default value actually used (30
seconds).
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the fwserial implementation which was returning -EPERM also for a
privileged user when trying to change certain unsupported parameters,
and instead return success consistently.
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of riv->ieee80211->LinkDetectInfo.SlotNum
that is a u16 type. There is a potential infinite loop if SlotNum
is larger than the u8 loop counter. Fix this by making the loop
counter the same type as SlotNum.
Addresses-Coverity: ("Infinite loop") Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210407150308.496623-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `ni_routes_test` module is not currently selectable using the
Kconfig files, but can be built by specifying `CONFIG_COMEDI_TESTS=m` on
the "make" command line. It currently fails to compile due to an extra
parameter added to the `ni_assign_device_routes` function by
commit e3b7ce73c578 ("staging: comedi: ni_routes: Allow alternate board
name for routes"). Fix it by supplying the value `NULL` for the added
`alt_board_name` parameter (which specifies that there is no alternate
board name).
Fixes: e3b7ce73c578 ("staging: comedi: ni_routes: Allow alternate board name for routes") Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20210407140142.447250-2-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c24 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Because a dependency on HAS_IOMEM and OF was added for the ADI AXI ADC
driver, this makes the AD9467 driver have some build/dependency issues
when OF is disabled (typically on ACPI archs like x86).
This is because the selection of the AD9467 enforces the ADI_AXI_ADC symbol
which is blocked by the OF (and potentially HAS_IOMEM) being disabled.
To fix this, we make the AD9467 driver depend on the ADI_AXI_ADC symbol.
The AD9467 driver cannot operate on it's own. It requires the ADI AXI ADC
driver to stream data (or some similar IIO interface).
So, the fix here is to make the AD9467 symbol depend on the ADI_AXI_ADC
symbol. At some point this could become it's own subgroup of high-speed
ADCs.
Fixes: be24c65e9fa24 ("iio: adc: adi-axi-adc: add proper Kconfig dependencies") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210324182746.9337-1-aardelean@deviqon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some SC7180 firmwares don't implement the QCOM_SCM_INFO_IS_CALL_AVAIL
API, so we can't probe the calling convention. We detect the legacy
calling convention on these firmwares, because the availability call
always fails and legacy is the fallback. This leads to problems where
the rmtfs driver fails to probe, because it tries to assign memory with
a bad calling convention, which then leads to modem failing to load and
all networking, even wifi, to fail. Ouch!
Let's force the calling convention to be what it always is on this SoC,
i.e. arm64. Of course, the calling convention is not the same thing as
implementing the QCOM_SCM_INFO_IS_CALL_AVAIL API. The absence of the "is
this call available" API from the firmware means that any call to
__qcom_scm_is_call_available() fails. This is OK for now though because
none of the calls that are checked for existence are implemented on
firmware running on sc7180. If such a call needs to be checked for
existence in the future, we presume that firmware will implement this
API and then things will "just work".
Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 9a434cee773a ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-4-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We shouldn't need to hold this spinlock here around the entire SCM call
into the firmware and back. Instead, we should be able to query the
firmware, potentially in parallel with other CPUs making the same
convention detection firmware call, and then grab the lock to update the
calling convention detected. The convention doesn't change at runtime so
calling into firmware more than once is possibly wasteful but simpler.
Besides, this is the slow path, not the fast path where we've already
detected the convention used.
More importantly, this allows us to add more logic here to workaround
the case where the firmware call to check for availability isn't
implemented in the firmware at all. In that case we can check the
firmware node compatible string and force a calling convention.
Note that we remove the 'has_queried' logic that is repeated twice. That
could lead to the calling convention being printed multiple times to the
kernel logs if the bool is true but __query_convention() is running on
multiple CPUs. We also shorten the time where the lock is held, but we
keep the lock held around the printk because it doesn't seem hugely
important to drop it for that.
Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 9a434cee773a ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-3-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make __qcom_scm_is_call_available() return bool instead of int. The
function has "is" in the name, so it should return a bool to indicate
the truth of the call being available. Unfortunately, it can return a
number < 0 which also looks "true", but not all callers expect that and
thus they think a call is available when really the check to see if the
call is available failed to figure it out.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Elliot Berman <eberman@codeaurora.org> Cc: Brian Masney <masneyb@onstation.org> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 0f206514749b ("scsi: firmware: qcom_scm: Add support for programming inline crypto keys") Fixes: 0434a4061471 ("firmware: qcom: scm: add support to restore secure config to qcm_scm-32") Fixes: b0a1614fb1f5 ("firmware: qcom: scm: add OCMEM lock/unlock interface") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210223214539.1336155-2-swboyd@chromium.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't clear the timer 1 configuration bits when clearing the interrupt flag
and counter overflow. As Michael reported, "This results in no timer
interrupts being delivered after the first. Initialization then hangs
in calibrate_delay as the jiffies counter is not updated."
On mvme16x, enable the timer after requesting the irq, consistent with
mvme147.
When stream config is failed, master runtime will release all
slave runtime in the slave_rt_list, but slave runtime is not
added to the list at this time. This patch frees slave runtime
in the config error path to fix the memory leak.
Fixes: 89e590535f32 ("soundwire: Add support for SoundWire stream management") Signed-off-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Keyon Jie <yang.jie@intel.com> Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20210331004610.12242-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
QFPROM controller hardware requires 1.8V min for fuse blowing.
So, this change sets the voltage to 1.8V, required to blow the fuse
for qfprom-efuse controller.
To disable fuse blowing, we set the voltage to 0V since this may
be a shared rail and may be able to run at a lower rate when we're
not blowing fuses.
Fixes: 93b4e49f8c86 ("nvmem: qfprom: Add fuse blowing support") Reported-by: Douglas Anderson <dianders@chromium.org> Suggested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20210330111241.19401-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
The function adf_isr_resource_alloc() is not unwinding correctly in case
of error.
This patch fixes the error paths and propagate the errors to the caller.
Fixes: 7afa232e76ce ("crypto: qat - Intel(R) QAT DH895xcc accelerator") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-11 points out a mismatch between the declaration and the definition
of poly1305_core_setkey():
lib/crypto/poly1305-donna32.c:13:67: error: argument 2 of type ‘const u8[16]’ {aka ‘const unsigned char[16]’} with mismatched bound [-Werror=array-parameter=]
13 | void poly1305_core_setkey(struct poly1305_core_key *key, const u8 raw_key[16])
| ~~~~~~~~~^~~~~~~~~~~
In file included from lib/crypto/poly1305-donna32.c:11:
include/crypto/internal/poly1305.h:21:68: note: previously declared as ‘const u8 *’ {aka ‘const unsigned char *’}
21 | void poly1305_core_setkey(struct poly1305_core_key *key, const u8 *raw_key);
This is harmless in principle, as the calling conventions are the same,
but the more specific prototype allows better type checking in the
caller.
Change the declaration to match the actual function definition.
The poly1305_simd_init() is a bit suspicious here, as it previously
had a 32-byte argument type, but looks like it needs to take the
16-byte POLY1305_BLOCK_SIZE array instead.
Fixes: 1c08a104360f ("crypto: poly1305 - add new 32 and 64-bit generic versions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec1f2619 ("phy: add support for USB cluster on the Armada 375 SoC") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When this was rewriten to get mainlined and start to
use 'linux/bitfield.h' headers, XTAL_MASK was wrong.
It must mask three bits but only two were used. Hence
properly fix it to make things work.
commit 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
found flag is used to indicate SoundWire devices that are
both enumerated on the bus and available in the device list.
However this flag is not reset correctly after one iteration,
This could miss some of the devices that are enumerated on the
bus but not in device list. So reset this correctly to fix this issue!
Put child node before return to fix potential reference count leak.
Generally, the reference count of child is incremented and decremented
automatically in the macro for_each_available_child_of_node() and should
be decremented manually if the loop is broken in loop body.
MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require
write permission. Depending on the hardware MEMLOCK might even be
write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK
is always write-once.
MEMSETBADBLOCK modifies the bad block table.
Fixes: f7e6b19bc764 ("mtd: properly check all write ioctls for permissions") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210303155735.25887-1-michael@walle.cc Signed-off-by: Sasha Levin <sashal@kernel.org>
To use additional properties 'bluetooth' on serial, need replace false with
'type: object' for 'additionalProperties' to make it as a node, else will
run into dtbs_check warnings.
'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: af1c2d81695b ("dt-bindings: serial: Convert STM32 UART to json-schema") Reported-by: kernel test robot <lkp@intel.com> Tested-by: Valentin Caron <valentin.caron@foss.st.com> Signed-off-by: dillon min <dillon.minfei@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/1616757302-7889-8-git-send-email-dillon.minfei@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 188db4435ac6 ("usb: gadget: s3c: use platform resources"),
'request_mem_region()' and 'ioremap()' are no more used, so they don't need
to be undone in the error handling path of the probe and in the remove
function.
Remove these calls and the unneeded 'rsrc_start' and 'rsrc_len' global
variables.
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown()
before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the
vf2pf_lock is initialized in adf_dev_init(), which can fail and when it
fail, the vf2pf_lock is either not initialized or destroyed, a subsequent
use of vf2pf_lock will cause issue.
To fix this issue, only set this flag if adf_dev_init() returns 0.
adf_vf_isr_resource_alloc() is not unwinding correctly when error
happens and it want to release uninitialized resources.
To fix this, only release initialized resources.
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Calling complete() from within the __init function is wrong -
theoretically, the init process could proceed all the way to freeing
the init mem before the devtmpfsd thread gets to execute the return
instruction in devtmpfs_setup().
In practice, it seems to be harmless as gcc inlines devtmpfs_setup()
into devtmpfsd(). So the calls of the __init functions init_chdir()
etc. actually happen from devtmpfs_setup(), but the __ref on that one
silences modpost (it's all right, because those calls happen before
the complete()). But it does make the __init annotation of the setup
function moot, which we'll fix in a subsequent patch.
Currently, the late microcode loading mechanism checks whether any CPUs
are offlined, and, in such a case, aborts the load attempt.
However, this must be done before the kernel caches new microcode from
the filesystem. Otherwise, when offlined CPUs are onlined later, those
cores are going to be updated through the CPU hotplug notifier callback
with the new microcode, while CPUs previously onine will continue to run
with the older microcode.
The rationale for why the update is aborted when at least one primary
thread is offline is because even if that thread is soft-offlined
and idle, it will still have to participate in broadcasted MCE's
synchronization dance or enter SMM, and in both examples it will execute
instructions so it better have the same microcode revision as the other
cores.
[ bp: Heavily edit and extend commit message with the reasoning behind all
this. ]
Fixes: 30ec26da9967 ("x86/microcode: Do not upload microcode if CPUs are offline") Signed-off-by: Otavio Pontes <otavio.pontes@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Acked-by: Ashok Raj <ashok.raj@intel.com> Link: https://lkml.kernel.org/r/20210319165515.9240-2-otavio.pontes@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Running out of request IDs on a channel essentially produces the same
effect as running out of space in the ring buffer, in that -EAGAIN is
returned. The error message in hv_ringbuffer_write() should either be
dropped (since we don't output a message when the ring buffer is full)
or be made conditional/debug-only.
Suggested-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Fixes: e8b7db38449ac ("Drivers: hv: vmbus: Add vmbus_requestor data structure for VMBus hardening") Link: https://lore.kernel.org/r/20210301191348.196485-1-parri.andrea@gmail.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
stm32_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 8d559a64f00b ("spi: stm32: drop devres version of spi_register_master") Reported-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Link: https://lore.kernel.org/r/1616052290-10887-1-git-send-email-alain.volmat@foss.st.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
test_syscall_vdso_32 ended up with an executable stacks because the asm
was missing the annotation that says that it is modern and doesn't need
an executable stack. Add the annotation.
This was missed in commit aeaaf005da1d ("selftests/x86: Add missing
.note.GNU-stack sections").
The probe() function returns an uninitialized variable in the success
path. There is no need for the "err" variable at all, just delete it.
Fixes: b014e9fae7e7 ("regulator: Support ROHM BD9576MUF and BD9573MUF") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Link: https://lore.kernel.org/r/YEsbfLJfEWtnRpoU@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A call to spi_unregister_master() triggers calling remove()
for all the spi devices binded to the spi master.
Some spi device driver requires to "talk" with the spi device
during the remove(), e.g.:
- a LCD panel like drivers/gpu/drm/panel/panel-lg-lg4573.c
will turn off the backlighting sending a command over spi.
This implies that the spi master must be fully functional when
spi_unregister_master() is called, either if it is called
explicitly in the master's remove() code or implicitly by the
devres framework.
Devres calls devres_release_all() to release all the resources
"after" the remove() of the spi master driver (check code of
__device_release_driver() in drivers/base/dd.c).
If the spi master driver has an empty remove() then there would
be no issue; the devres_release_all() will release everything
in reverse order w.r.t. probe().
But if code in spi master driver remove() disables the spi or
makes it not functional (like in this spi-stm32), then devres
cannot be used safely for unregistering the spi master and the
binded spi devices.
Replace devm_spi_register_master() with spi_register_master()
and add spi_unregister_master() as first action in remove().
Fixes: dcbe0d84dfa5 ("spi: add driver for STM32 SPI controller") Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com> Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Link: https://lore.kernel.org/r/1615545286-5395-1-git-send-email-alain.volmat@foss.st.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case where the dma_iv mapping fails, the return error path leaks
the memory allocated to object d. Fix this by adding a new error return
label and jumping to this to ensure d is free'd before the return.
Addresses-Coverity: ("Resource leak") Fixes: ac2614d721de ("crypto: sun8i-ss - Add support for the PRNG") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
WSA881x powerdown pin is connected to GPIO1 not gpio2, so correct this.
This was working so far due to a shift bug in gpio driver, however
once that is fixed this will stop working, so fix this!
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
projects / thirdparty / kernel / stable.git / log
