In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.
In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().
[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.
Fixes: 6e5e959dde0d ("pinctrl: API changes to support multiple states per device") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.
This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com> Tested-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Check the status of the DMM engine after it is reported that the
transaction was completed as in rare cases the engine might not reached a
working state.
The wait_status() will print information in case the DMM is not reached the
expected state and the dmm_txn_commit() will return with an error code to
make sure that we are not continuing with a broken setup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Set the resource type when we reserve VGA-related I/O port resources.
The resource code doesn't actually look at the type, so it inserts
resources without a type in the tree correctly even without this change.
But if we ever print a resource without a type, it looks like this:
vga+ [??? 0x000003c0-0x000003df flags 0x0]
Setting the type means it will be printed correctly as:
In ib_umem structure npages holds original number of sg entries, while
nmap is number of DMA blocks returned by dma_map_sg.
Fixes: c5d76f130b28 ('IB/core: Add umem function to read data from user-space') Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The ipoib path database is organized around DGIDs from the LLADDR, but the
SA is free to return a different GID when asked for path. This causes a
bug because the SA's modified DGID is copied into the database key, even
though it is no longer the correct lookup key, causing a memory leak and
other malfunctions.
Ensure the database key does not change after the SA query completes.
Demonstration of the bug is as follows
ipoib wants to send to GID fe80:0000:0000:0000:0002:c903:00ef:5ee2, it
creates new record in the DB with that gid as a key, and issues a new
request to the SM.
Now, the SM from some reason returns path-record with other SGID (for
example, 2001:0000:0000:0000:0002:c903:00ef:5ee2 that contains the local
subnet prefix) now ipoib will overwrite the current entry with the new
one, and if new request to the original GID arrives ipoib will not find
it in the DB (was overwritten) and will create new record that in its
turn will also be overwritten by the response from the SM, and so on
till the driver eats all the device memory.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
On faster CPUs a delay is required after the resume command and the restart command. Without the delay, the restart command often returns -EREMOTEIO and the Si2168 does not restart.
Note that this patch fixes the same issue as https://patchwork.linuxtv.org/patch/44304/, but I believe my udelay() fix addresses the actual problem.
Reset the driver current tx read/write index to zero when inactiveps
nic out of sync with HW state. Wrong driver tx read/write index will
cause Tx fail.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
drivers/infiniband/core/iwpm_util.c: In function ‘iwpm_send_mapinfo’:
drivers/infiniband/core/iwpm_util.c:647: warning: ‘ret’ may be used uninitialized in this function
Indeed, if nl_client is not found in any of the scanned has buckets, ret
will be used uninitialized.
Preinitialize ret to -EINVAL to fix this.
Fixes: 30dc5e63d6a5ad24 ("RDMA/core: Add support for iWARP Port Mapper user space service") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
get_pages doesn't keep a reference of the pages allocated
when it fails later in the code path. This can lead to
a memory leak. Keep reference of the allocated pages so
that it can be freed when msm_gem_free_object gets called
later during cleanup.
Signed-off-by: Prakash Kamliya <pkamliya@codeaurora.org> Signed-off-by: Sharat Masetty <smasetty@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The WDIOC_SETOPTIONS case in the watchdog ioctl would alwayss falls
through to the -EINVAL case. This is wrong since thew watchdog does
actually get stopped or started correctly.
The issue is that the internal counter that triggers the watchdog reset
is actually running at 4096 Hz instead of 1Hz, therefore the value
given by userland (in sec) needs to be multiplied by 4096 to get the
correct behavior.
January is month 1. There is no zero-th month. If someone passes a
zero month then it means we read from one space before the start of the
total_days_of_prev_months[] array.
We may as well also be strict about days as well.
Fixes: 1bd5bbcb6531 ("[CIFS] Legacy time handling for Win9x and OS/2 part 1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
If fbmem iomemory mapping failed, sm501fb_start() breaks off
initialization, deallocates resources, but returns zero.
As a result, double deallocation can happen in sm501fb_stop().
Found by Linux Driver Verification project (linuxtesting.org).
Starting from gcc-5.4+ gcc generates MLX instructions in more cases to
refer local symbols:
https://gcc.gnu.org/PR60465
That caused ia64 module loader to choke on such instructions:
fuse: invalid slot number 1 for IMM64
The Linux kernel used to handle only case where relocation pointed to
slot=2 instruction in the bundle. That limitation was fixed in linux by
commit 9c184a073bfd ("[IA64] Fix 2.6 kernel for the new ia64 assembler")
See
Commit 6f287ca(md/raid10: reset the 'first' at the end of loop) ignores
a case in reshape, the first rdev could be a spare disk, which shouldn't
be accounted as the first disk since it doesn't include the offset info.
Fix: 6f287ca(md/raid10: reset the 'first' at the end of loop) Cc: Guoqing Jiang <gqjiang@suse.com> Cc: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The bnx2x driver is not providing proper alignment on the receive buffers it
passes to build_skb(), causing skb_shared_info to be misaligned.
skb_shared_info contains an atomic, and while PPC normally supports
unaligned accesses, it does not support unaligned atomics.
Aligning the size of rx buffers will ensure that page_frag_alloc() returns
aligned addresses.
This can be reproduced on PPC by setting the network MTU to 1450 (or other
non-multiple-of-4) and then generating sufficient inbound network traffic
(one or two large "wget"s usually does it), producing the following oops:
The power table addresses should be contiguous, but there was a hole
where 0x34 was missing. On most devices this is not a problem as
addresses above 0x34 are used for the BUC# convertors which are not
used in the DSDTs I've access to but after the BUC# convertors
there is a field named GPI1 in the DSTDs, which does get used in some
cases and ended up turning BUC6 on and off due to the wrong addresses,
resulting in turning the entire device off (or causing it to reboot).
Removing the hole in the addresses fixes this, fixing one of my
Bay Trail tablets turning off while booting the mainline kernel.
While at it add comments with the field names used in the DSDTs to
make it easier to compare the register and bits used at each address
with the datasheet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Commit c49c097610fe ("ipmi: Don't call receive handler in the
panic context") means that the panic_recv_free is not called during a
panic and the atomic count does not drop to 0.
Fix this by only expecting one decrement of the atomic variable
which comes from panic_smi_free.
The PCIe programming sequence in TRM suggests CLKSTCTRL of PCIe should be
set to SW_WKUP. There are no issues when CLKSTCTRL is set to HW_AUTO in RC
mode. However in EP mode, the host system is not able to access the
MEMSPACE and setting the CLKSTCTRL to SW_WKUP fixes it.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
POWERHOLD signal has higher priority over the DEV_ON bit.
So power off will not happen if the POWERHOLD is held high.
Hence reset the MUX to GPIO_7 mode to release the POWERHOLD
and the DEV_ON bit to take effect to power off the PMIC.
PMIC Power off happens in dire situations like thermal shutdown
so irrespective of the POWERHOLD setting go ahead and turn off
the powerhold. Currently poweroff is broken on boards that have
powerhold enabled. This fixes poweroff on those boards.
Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
Normally we don't have inline extents followed by regular extents, but
there's currently at least one harmless case where this happens. For
example, when the page size is 4Kb and compression is enabled:
In this case we get a compressed inline extent, representing 4Kb of
data, followed by a hole extent and then a regular data extent. The
inline extent was not expanded/converted to a regular extent exactly
because it represents 4Kb of data. This does not cause any apparent
problem (such as the issue solved by commit e1699d2d7bf6
("btrfs: add missing memset while reading compressed inline extents"))
except trigger an unexpected case in the incremental send code path
that makes us issue an operation to write a hole when it's not needed,
resulting in more writes at the receiver and wasting space at the
receiver.
So teach the incremental send code to deal with this particular case.
The issue can be currently triggered by running fstests btrfs/137 with
compression enabled (MOUNT_OPTIONS="-o compress" ./check btrfs/137).
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Function create_singlethread_workqueue() will return a NULL pointer if
there is no enough memory, and its return value should be validated
before using. However, in function rndis_wlan_bind(), its return value
is not checked. This may cause NULL dereference bugs. This patch fixes
it.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.
1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure
consider the sequence of commands:
mkdir -p /import/nfs /import/bind /import/etc
mount --bind / /import/bind
mount --make-private /import/bind
mount --bind /import/etc /import/bind/etc
exportfs -o rw,no_root_squash,crossmnt,async,no_subtree_check localhost:/
mount -o vers=4 localhost:/ /import/nfs
ls -l /import/nfs/etc
You would not expect this to report a stale file handle.
Yet it does.
The manipulations under /import/bind cause the dentry for
/etc to get the DCACHE_MOUNTED flag set, even though nothing
is mounted on /etc. This causes nfsd to call
nfsd_cross_mnt() even though there is no mountpoint. So an
upcall to mountd for "/etc" is performed.
The 'crossmnt' flag on the export of / causes mountd to
report that /etc is exported as it is a descendant of /. It
assumes the kernel wouldn't ask about something that wasn't
a mountpoint. The filehandle returned identifies the
filesystem and the inode number of /etc.
When this filehandle is presented to rpc.mountd, via
"nfsd.fh", the inode cannot be found associated with any
name in /etc/exports, or with any mountpoint listed by
getmntent(). So rpc.mountd says the filehandle doesn't
exist. Hence ESTALE.
This is fixed by teaching nfsd not to trust DCACHE_MOUNTED
too much. It is just a hint, not a guarantee.
Change nfsd_mountpoint() to return '1' for a certain mountpoint,
'2' for a possible mountpoint, and 0 otherwise.
Then change nfsd_crossmnt() to check if follow_down()
actually found a mountpount and, if not, to avoid performing
a lookup if the location is not known to certainly require
an export-point.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Commit da244654c66e ("[SCSI] mac_esp: fix for quadras with two esp
chips") added mac_scsi_esp_intr() to handle the IRQ lines from a pair of
on-board ESP chips (a normal shared IRQ did not work).
Proper mutual exclusion was missing from that patch. This patch fixes
race conditions between comparison and assignment of esp_chips[]
pointers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function qlcnic_sriov_virtid_fn(), its return value is used
without validation. This may result in invalid memory access bugs. This
patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
There are two versions of a structure for queue creation and setup that the
driver shares with FW. The driver was only treating as version 0.
Verify WQ_CREATE with 128B WQEs in V0 and V1.
Code review of another bug showed the driver passing
128B WQEs and 8 pages in WQ CREATE and V0.
Code inspection/instrumentation showed that the driver
uses V0 in WQ_CREATE and if the caller passes queue->entry_size
128B, the driver sets the hdr_version to V1 so all is good.
When I tested the V1 WQ_CREATE, the mailbox failed causing
the driver to unload.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Update the broadcast address in the priv->broadcast object when the
Pkey value changes in index 0, otherwise the multicast GID value will
keep the previous value of the PKey, and will not be updated.
This leads to interface state down because the interface will keep the
old PKey value.
For example, in SR-IOV environment, if the PF changes the value of PKey
index 0 for one of the VFs, then the VF receives PKey change event that
triggers heavy flush. This flush calls update_parent_pkey that update the
broadcast object and its relevant members. If in this case the multicast
GID will not be updated, the interface state will be down.
After an upgrade to Linux kernel v4.x the hardware timestamps of the
82579 Gigabit Ethernet Controller are different than expected.
The values that are being read are almost four times as big as before
the kernel upgrade.
The difference is that after the upgrade the driver sets the clock
frequency to 25MHz, where before the upgrade it was set to 96MHz. Intel
confirmed that the correct frequency for this network adapter is 96MHz.
Signed-off-by: Bernd Faust <berndfaust@gmail.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
When using TCP FastOpen for an active session, we send one wakeup event
from tcp_finish_connect(), right before the data eventually contained in
the received SYNACK is queued to sk->sk_receive_queue.
This means that depending on machine load or luck, poll() users
might receive POLLOUT events instead of POLLIN|POLLOUT
To fix this, we need to move the call to sk->sk_state_change()
after the (optional) call to tcp_rcv_fastopen_synack()
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Commit a7d42ddb3099727f58366fa006f850a219cce6c8 ("nfs: add mirroring
support to pgio layer") moved pg_cleanup out of the path when there was
non-sequental I/O that needed to be flushed. The result is that for
layouts that have more than one layout segment per file, the pg_lseg is not
cleared, so we can end up hitting the WARN_ON_ONCE(req_start >= seg_end) in
pnfs_generic_pg_test since the pg_lseg will be pointing to that
previously-flushed layout segment.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Fixes: a7d42ddb3099 ("nfs: add mirroring support to pgio layer") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Move the registration of the OMAP IOMMU platform driver before
setting the IOMMU callbacks on the platform bus. This causes
the IOMMU devices to be probed first before the .add_device()
callback is invoked for all registered devices, and allows
the iommu_group support to be added to the OMAP IOMMU driver.
While at this, also check for the return status from bus_set_iommu.
The support for dynamic ftrace with CONFIG_DEBUG_RODATA involves
overriding the weak arch_ftrace_update_code() with a variant which makes
the kernel text writable around the patching.
This override was however added under the CONFIG_OLD_MCOUNT ifdef, and
CONFIG_OLD_MCOUNT is only enabled if frame pointers are enabled.
This leads to non-functional dynamic ftrace (ftrace triggers a
WARN_ON()) when CONFIG_DEBUG_RODATA is enabled and CONFIG_FRAME_POINTER
is not.
Move the override out of that ifdef and into the CONFIG_DYNAMIC_FTRACE
ifdef where it belongs.
Fixes: 80d6b0c2eed2a ("ARM: mm: allow text and rodata sections to be read-only") Suggested-by: Nicolai Stange <nicstange@gmail.com> Suggested-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Abel Vesa <abelvesa@gmail.com> Acked-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
At the moment kvmppc_mmu_map_page() returns -1 if
mmu_hash_ops.hpte_insert() fails for any reason so the page fault handler
resumes the guest and it faults on the same address again.
This adds distinction to kvmppc_mmu_map_page() to return -EIO if
mmu_hash_ops.hpte_insert() failed for a reason other than full pteg.
At the moment only pSeries_lpar_hpte_insert() returns -2 if
plpar_pte_enter() failed with a code other than H_PTEG_FULL.
Other mmu_hash_ops.hpte_insert() instances can only fail with
-1 "full pteg".
With this change, if PR KVM fails to update HPT, it can signal
the userspace about this instead of returning to guest and having
the very same page fault over and over again.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Passed through SCSI targets may have transfer limits which come from the
host SCSI controller or something on the host side other than the target
itself.
To make this work properly, the hypervisor can adjust the target's VPD
information to advertise these limits. But for that to work, the guest
has to look at the VPD pages, which we won't do by default if it is an
SPC-2 device, even if it does actually support it.
This adds a workaround to address this, forcing devices attached to a
virtio-scsi controller to always check the VPD pages. This is modelled
on a similar workaround for the storvsc (Hyper-V) SCSI controller,
although that exists for slightly different reasons.
A specific case which causes this is a volume from IBM's IPR RAID
controller (which presents as an SPC-2 device, although it does support
VPD) passed through with qemu's 'scsi-block' device.
[mkp: fixed typo]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
As per latest regulatory update for India, channel 52, 56, 60, 64
is no longer restricted to DFS. Enabling DFS/no infra flags in driver
results in applying all DFS related restrictions (like doing CAC etc
before this channel moves to 'available state') for these channels
even though the country code is programmed as 'India' in he hardware,
fix this by relaxing the frequency range while applying RADAR flags
only if the country code is programmed to India. If the frequency range
needs to modified based on different country code, ath_is_radar_freq
can be extended/modified dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The dw_mmio driver disables the block clock before unregistering
the host. The code unregistering the host may access the SPI block
registers. If register access happens with block clock disabled,
this may lead to a bus hang. Disable the clock after unregistering
the host to prevent such situation.
This bug was observed on Altera Cyclone V SoC.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
It started with a sporadic message in syslog: "CAM tried to send a
buffer larger than the ecount size" This message is not the fault
itself, but a consecutive fault, after a read error from the CAM. This
happens only on several CAMs, several hardware, and of course sporadic.
It is a consecutive fault, if the last read from the CAM did fail. I
guess this will not happen on all CAMs, but at least it did on mine.
There was a write error to the CAM and during the re-initialization
procedure, the CAM finished the last read, although it got a RS.
The write error to the CAM happened because a race condition between HC
write, checking DA and FR.
This patch added an additional check for DA(RE), just after checking FR.
It is important to read the CAMs status register again, to give the CAM
the necessary time for a proper reaction to HC. Please note the
description within the source code (patch below).
ndisc_notify is the ipv6 equivalent to arp_notify. When arp_notify is
set to 1, gratuitous arp requests are sent when the device is brought up.
The same is expected when ndisc_notify is set to 1 (per ndisc_notify in
Documentation/networking/ip-sysctl.txt). The NA is not sent on NETDEV_UP
event; add it.
Fixes: 5cb04436eef6 ("ipv6: add knob to send unsolicited ND on link-layer address change") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Description of the problem:
- i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM";
- the fist HID (SMBUS01) is clearly defined in "SMBus Control Method
Interface Specification, version 1.0": "Each device must specify
'SMBUS01' as its _HID and use a unique _UID value";
- unfortunately, BIOS vendors (like AMI) seem to ignore this requirement
and implement "SMB0001" HID instead of "SMBUS01";
- I speculate that they do this because only "SMB0001" is hard coded in
Windows SMBus driver produced by Microsoft.
This leads to following situation:
- SMBus works out of box in Windows but not in Linux;
- board vendors are forced to add correct "SMBUS01" HID to BIOS to make
SMBus work in Linux. Moreover the same board vendors complain that
tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier
and produce errors. So they need to constantly patch the compiler for
each new version of BIOS.
As it is very unlikely that BIOS vendors implement a correct HID in
future, I would propose to consider whether it is possible to work around
the problem by adding MS HID to the Linux i2c-scmi driver.
v2: move the definition of the new HID to the driver itself.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru> Signed-off-by: Michael Brunner <Michael.Brunner@kontron.com> Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
When requesting a shared irq with IRQF_TRIGGER_NONE then the irqaction
flags get filled with the trigger type from the irq_data:
if (!(new->flags & IRQF_TRIGGER_MASK))
new->flags |= irqd_get_trigger_type(&desc->irq_data);
On the first setup_irq() the trigger type in irq_data is NONE when the
above code executes, then the irq is started up for the first time and
then the actual trigger type gets established, but that's too late to fix
up new->flags.
When then a second user of the irq requests the irq with IRQF_TRIGGER_NONE
its irqaction's triggertype gets set to the actual trigger type and the
following check fails:
if (!((old->flags ^ new->flags) & IRQF_TRIGGER_MASK))
Resulting in the request_irq failing with -EBUSY even though both
users requested the irq with IRQF_SHARED | IRQF_TRIGGER_NONE
Fix this by comparing the new irqaction's trigger type to the trigger type
stored in the irq_data which correctly reflects the actual trigger type
being used for the irq.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/20170415100831.17073-1-hdegoede@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The target() callback must run on the affected cpu. This is achieved by
temporarily setting the affinity of the calling thread to the requested CPU
and reset it to the original affinity afterwards.
That's racy vs. concurrent affinity settings for that thread resulting in
code executing on the wrong CPU.
Replace it by work_on_cpu(). All call pathes which invoke the callbacks are
already protected against CPU hotplug.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: linux-pm@vger.kernel.org Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/20170412201042.958216363@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
acpi_processor_get_throttling() requires to invoke the getter function on
the target CPU. This is achieved by temporarily setting the affinity of the
calling user space thread to the requested CPU and reset it to the original
affinity afterwards.
That's racy vs. CPU hotplug and concurrent affinity settings for that
thread resulting in code executing on the wrong CPU and overwriting the
new affinity setting.
acpi_processor_get_throttling() is invoked in two ways:
1) The CPU online callback, which is already running on the target CPU and
obviously protected against hotplug and not affected by affinity
settings.
2) The ACPI driver probe function, which is not protected against hotplug
during modprobe.
Switch it over to work_on_cpu() and protect the probe function against CPU
hotplug.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/20170412201042.785920903@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The name field in structure i2c_device_id is 20 characters, and we expect
it to be NULL-terminated, however we are trying to stuff it with 21 bytes
and thus NULL-terminator is lost. This causes issues when one creates
device with name "MICROCHIP_AR1021_I2C" as i2c core cuts off the last "C",
and automatic module loading by alias does not work as result.
The -I2C suffix in the device name is superfluous, we know what bus we are
dealing with, so let's drop it. Also, no other driver uses capitals, and
the manufacturer name is normally not included, except in very rare cases
of incompatible name collisions.
The classic PC rtc-coms driver has a workaround for broken ACPI device
nodes for it which lack an irq resource. This workaround used to
unconditionally hardcode the irq to 8 in these cases.
This was causing irq conflict problems on systems without a legacy-pic
so a recent patch added an if (nr_legacy_irqs()) guard to the
workaround to avoid this irq conflict.
nr_legacy_irqs() uses the legacy_pic symbol under the hood causing
an undefined symbol error if the rtc-cmos code is build as a module.
This commit exports the legacy_pic symbol to fix this.
Cc: rtc-linux@googlegroups.com Cc: alexandre.belloni@free-electrons.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
According to MS-SMB2 3.2.55 validate_negotiate request must
always be signed. Some Windows can fail the request if you send it unsigned
See kernel bugzilla bug 197311
CC: Stable <stable@vger.kernel.org> Acked-by: Ronnie Sahlberg <lsahlber.redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Corrected the register to check the 64-bit pointer
capability state. 64-bit pointer implementation capability
was checking in wrong register, which causes the BDC
enumeration failure in 64-bit memory address.
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for
Broadcom USB3.0 device controller IP BDC")
In case of using DUP, we search for enough unallocated disk space on a
device to hold two stripes.
The devices_info[ndevs-1].max_avail that holds the amount of unallocated
space found is directly assigned to stripe_size, while it's actually
twice the stripe size.
Later on in the code, an unconditional division of stripe_size by
dev_stripes corrects the value, but in the meantime there's a check to
see if the stripe_size does not exceed max_chunk_size. Since during this
check stripe_size is twice the amount as intended, the check will reduce
the stripe_size to max_chunk_size if the actual correct to be used
stripe_size is more than half the amount of max_chunk_size.
The unconditional division later tries to correct stripe_size, but will
actually make sure we can't allocate more than half the max_chunk_size.
Fix this by moving the division by dev_stripes before the max chunk size
check, so it always contains the right value, instead of putting a duct
tape division in further on to get it fixed again.
Since in all other cases than DUP, dev_stripes is 1, this change only
affects DUP.
Other attempts in the past were made to fix this:
* 37db63a400 "Btrfs: fix max chunk size check in chunk allocator" tried
to fix the same problem, but still resulted in part of the code acting
on a wrongly doubled stripe_size value.
* 86db25785a "Btrfs: fix max chunk size on raid5/6" unintentionally
broke this fix again.
The real problem was already introduced with the rest of the code in 73c5de0051.
The user visible result however will be that the max chunk size for DUP
will suddenly double, while it's actually acting according to the limits
in the code again like it was 5 years ago.
Reported-by: Naohiro Aota <naohiro.aota@wdc.com> Link: https://www.spinics.net/lists/linux-btrfs/msg69752.html Fixes: 73c5de0051 ("btrfs: quasi-round-robin for chunk allocation") Fixes: 86db25785a ("Btrfs: fix max chunk size on raid5/6") Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ update comment ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
dxfer_len is an unsigned int and we always assign a value > 0 to it, so
it doesn't make any sense to check if it is < 0. We can't really check
dxferp as well as we have both NULL and not NULL cases in the possible
call paths.
So just return true for SG_DXFER_FROM_DEV transfer in
sg_is_valid_dxfer().
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reported-by: Colin Ian King <colin.king@canonical.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
SG_DXFER_FROM_DEV transfers do not necessarily have a dxferp as we set
it to NULL for the old sg_io read/write interface, but must have a
length bigger than 0. This fixes a regression introduced by commit 28676d869bbb ("scsi: sg: check for valid direction before starting the
request")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: 28676d869bbb ("scsi: sg: check for valid direction before starting the request") Reported-by: Chris Clayton <chris2553@googlemail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
When struct its_device instances are created, the nr_ites member
will be set to a power of 2 that equals or exceeds the requested
number of MSIs passed to the msi_prepare() callback. At the same
time, the LPI map is allocated to be some multiple of 32 in size,
where the allocated size may be less than the requested size
depending on whether a contiguous range of sufficient size is
available in the global LPI bitmap.
This may result in the situation where the nr_ites < nr_lpis, and
since nr_ites is what we program into the hardware when we map the
device, the additional LPIs will be non-functional.
For bog standard hardware, this does not really matter. However,
in cases where ITS device IDs are shared between different PCIe
devices, we may end up allocating these additional LPIs without
taking into account that they don't actually work.
So let's make nr_ites at least 32. This ensures that all allocated
LPIs are 'live', and that its_alloc_device_irq() will fail when
attempts are made to allocate MSIs beyond what was allocated in
the first place.
While converting ioctx index from a list to a table, db446a08c23d
("aio: convert the ioctx list to table lookup v3") missed tagging
kioctx_table->table[] as an array of RCU pointers and using the
appropriate RCU accessors. This introduces a small window in the
lookup path where init and access may race.
Mark kioctx_table->table[] with __rcu and use the approriate RCU
accessors when using the field.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Jann Horn <jannh@google.com> Fixes: db446a08c23d ("aio: convert the ioctx list to table lookup v3") Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org # v3.12+ Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
While fixing refcounting, e34ecee2ae79 ("aio: Fix a trinity splat")
incorrectly removed explicit RCU grace period before freeing kioctx.
The intention seems to be depending on the internal RCU grace periods
of percpu_ref; however, percpu_ref uses a different flavor of RCU,
sched-RCU. This can lead to kioctx being freed while RCU read
protected dereferences are still in progress.
Fix it by updating free_ioctx() to go through call_rcu() explicitly.
In case when dentry passed to lock_parent() is protected from freeing only
by the fact that it's on a shrink list and trylock of parent fails, we
could get hit by __dentry_kill() (and subsequent dentry_kill(parent))
between unlocking dentry and locking presumed parent. We need to recheck
that dentry is alive once we lock both it and parent *and* postpone
rcu_read_unlock() until after that point. Otherwise we could return
a pointer to struct dentry that already is rcu-scheduled for freeing, with
->d_lock held on it; caller's subsequent attempt to unlock it can end
up with memory corruption.
When releasing a client, we need to clear the clienttab[] entry at
first, then call snd_seq_queue_client_leave(). Otherwise, the
in-flight cell in the queue might be picked up by the timer interrupt
via snd_seq_check_queue() before calling snd_seq_queue_client_leave(),
and it's delivered to another queue while the client is clearing
queues. This may eventually result in an uncleared cell remaining in
a queue, and the later snd_seq_pool_delete() may need to wait for a
long time until the event gets really processed.
By moving the clienttab[] clearance at the beginning of release, any
event delivery of a cell belonging to this client will fail at a later
point, since snd_seq_client_ptr() returns NULL. Thus the cell that
was picked up by the timer interrupt will be returned immediately
without further delivery, and the long stall of snd_seq_delete_pool()
can be avoided, too.
Although we've covered the races between concurrent write() and
ioctl() in the previous patch series, there is still a possible UAF in
the following scenario:
So the problem is that a cell is peeked and accessed without any
protection until it's retrieved from the queue again via
snd_seq_prioq_cell_out().
This patch tries to address it, also cleans up the code by a slight
refactoring. snd_seq_prioq_cell_out() now receives an extra pointer
argument. When it's non-NULL, the function checks the event timestamp
with the given pointer. The caller needs to pass the right reference
either to snd_seq_tick or snd_seq_realtime depending on the event
timestamp type.
A good news is that the above change allows us to remove the
snd_seq_prioq_cell_peek(), too, thus the patch actually reduces the
code size.
snd_pcm_oss_get_formats() has an obvious use-after-free around
snd_mask_test() calls, as spotted by syzbot. The passed format_mask
argument is a pointer to the hw_params object that is freed before the
loop. What a surprise that it has been present since the original
code of decades ago...
Gratian Crisan reported that vmalloc_fault() crashes when CONFIG_HUGETLBFS
is not set since the function inadvertently uses pXn_huge(), which always
return 0 in this case. ioremap() does not depend on CONFIG_HUGETLBFS.
Fix vmalloc_fault() to call pXd_large() instead.
Fixes: f4eafd8bcd52 ("x86/mm: Fix vmalloc_fault() to handle large pages properly") Reported-by: Gratian Crisan <gratian.crisan@ni.com> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Cc: linux-mm@kvack.org Cc: Borislav Petkov <bp@alien8.de> Cc: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/20180313170347.3829-2-toshi.kani@hpe.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Custom policies can require file signatures based on LSM labels. These
files are normally created and only afterwards labeled, requiring them
to be signed.
Instead of requiring file signatures based on LSM labels, entire
filesystems could require file signatures. In this case, we need the
ability of writing new files without requiring file signatures.
The definition of a "new" file was originally defined as any file with
a length of zero. Subsequent patches redefined a "new" file to be based
on the FILE_CREATE open flag. By combining the open flag with a file
size of zero, this patch relaxes the file signature requirement.
The 'configinit.sh' script checks the format of optional argument for the
build directory, printing an error message if the format is not valid.
However, the error message uses the wrong variable, indicating an empty
string even though the user entered a non-empty (but erroneous) string.
This commit fixes the script to use the correct variable.
Fixes: c87b9c601ac8 ("rcutorture: Add KVM-based test framework") Signed-off-by: SeongJae Park <sj38.park@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <amit.sikka@ericsson.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
In the ieee80211_setup_sdata() we check if the interface type is valid
and, if not, call BUG(). This should never happen, but if there is
something wrong with the code, it will not be caught until the bug
happens when an interface is being set up. Calling BUG() is too
extreme for this and a WARN_ON() would be better used instead. Change
that.
Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll,
only if PS_ENABLED was set before.
This is required due to commit c9491367b759 ("mac80211: always update the
PM state of a peer on MGMT / DATA frames") that enforces the ap to
check only mgmt/data frames ps bit, and then update station's power save
accordingly.
When sending only ps-poll (control frame) the ap will not be aware that
the station entered power save.
Setting ps enable before triggering ps_poll, will send NDP with PM bit
enabled first.
Before accessing the GGTT we must flush the PTE writes and make them
visible to the chipset, or else the indirect access may end up in the
wrong page. In commit 3497971a71d8 ("agp/intel: Flush chipset writes
after updating a single PTE"), we noticed corruption of the uploads for
pwrite and for capturing GPU error states, but it was presumed that the
explicit calls to intel_gtt_chipset_flush() were sufficient for the
execbuffer path. However, we have not been flushing the chipset between
the PTE writes and access via the GTT itself.
For simplicity, do the flush after any PTE update rather than try and
batch the flushes on a just-in-time basis.
References: 3497971a71d8 ("agp/intel: Flush chipset writes after updating a single PTE") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: drm-intel-fixes@lists.freedesktop.org Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171208214616.30147-1-chris@chris-wilson.co.uk Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Kobject created using kobject_create_and_add() can be freed using
kobject_put() when there is no referenece any more. However,
kobject memory allocated with kzalloc() has to set up a release
callback in order to free it when the counter decreases to 0.
Otherwise it causes memory leak.
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array. The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.
Fixes: ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e8af (spi: sunxi: Add Allwinner A31 SPI controller driver) Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Indeed musl doesn't define old SIGCLD signal name but only new one SIGCHLD.
SIGCHLD is the new POSIX name for that signal so it doesn't change
anything on other libcs.
This fixes this kind of build error:
usbipd.c: In function ‘set_signal’:
usbipd.c:459:12: error: 'SIGCLD' undeclared (first use in this function)
sigaction(SIGCLD, &act, NULL);
^~~~~~
usbipd.c:459:12: note: each undeclared identifier is reported only once
for each function it appears in
Makefile:407: recipe for target 'usbipd.o' failed
make[3]: *** [usbipd.o] Error 1
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board") Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Currently it is possible to add or update socket policies, but
not clear them. Therefore, once a socket policy has been applied,
the socket cannot be used for unencrypted traffic.
This patch allows (privileged) users to clear socket policies by
passing in a NULL pointer and zero length argument to the
{IP,IPV6}_{IPSEC,XFRM}_POLICY setsockopts. This results in both
the incoming and outgoing policies being cleared.
The simple approach taken in this patch cannot clear socket
policies in only one direction. If desired this could be added
in the future, for example by continuing to pass in a length of
zero (which currently is guaranteed to return EMSGSIZE) and
making the policy be a pointer to an integer that contains one
of the XFRM_POLICY_{IN,OUT} enum values.
An alternative would have been to interpret the length as a
signed integer and use XFRM_POLICY_IN (i.e., 0) to clear the
input policy and -XFRM_POLICY_OUT (i.e., -1) to clear the output
policy.
This splat cannot be generated by expedited grace periods because they
always invoke resched_cpu() on the current CPU, which is good because
expedited grace periods require that resched_cpu() unconditionally
succeed. However, other parts of RCU can tolerate resched_cpu() acting
as a no-op, at least as long as it doesn't happen too often.
This commit therefore makes resched_cpu() invoke resched_curr() only if
the CPU is either online or is the current CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
ELO devices have one Button usage in GenDesk field, which makes hid-input map
it to BTN_LEFT; that confuses userspace, which then considers the device to be
a mouse/touchpad instead of touchscreen.
Fix that by unmapping BTN_LEFT and keeping only BTN_TOUCH in place.
HDMI 2.0 Appendix F suggest that we should keep sending the infoframe
when switching from 3D to 2D mode, even if the infoframe isn't strictly
necessary (ie. not needed to transmit the VIC or stereo information).
This is a workaround against some sinks that fail to realize that they
should switch from 3D to 2D mode when the source stop transmitting
the infoframe.
v2: Handle unpack() as well
Pull the length calculation into a helper
Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: linux-media@vger.kernel.org Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> #v1 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171113170427.4150-2-ville.syrjala@linux.intel.com Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Since drm_edid_to_eld() knows the connector type, we can set the type in
ELD while at it. Most connectors this gets called on are not DP
encoders, and with the HDMI type being 0, this does not change behaviour
for non-DP.
For i915 having this in place earlier would have saved a considerable
amount of debugging that lead to the fix 2d8f63297b9f ("drm/i915: always
update ELD connector type after get modes"). I don't see other drivers,
even the ones calling drm_edid_to_eld() on DP connectors, setting the
connector type in ELD.
Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Russell King <linux@armlinux.org.uk> Cc: CK Hu <ck.hu@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Mark Yao <mark.yao@rock-chips.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Eric Anholt <eric@anholt.net> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/d527b31619528c477c2c136f25cdf118bc0cfc1d.1509545641.git.jani.nikula@intel.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Set the pages which is used for kprobes' singlestep buffer
and optprobe's trampoline instruction buffer to readonly.
This can prevent unexpected (or unintended) instruction
modification.
This also passes rodata_test as below.
Without this patch, rodata_test shows a warning:
WARNING: CPU: 0 PID: 1 at arch/x86/mm/dump_pagetables.c:235 note_page+0x7a9/0xa20
x86/mm: Found insecure W+X mapping at address ffffffffa0000000/0xffffffffa0000000
With this fix, no W+X pages are found:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
rodata_test: all tests were successful
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David S . Miller <davem@davemloft.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ye Xiaolong <xiaolong.ye@intel.com> Link: http://lkml.kernel.org/r/149076375592.22469.14174394514338612247.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Fix the kprobe-booster not to boost far call instruction,
because a call may store the address in the single-step
execution buffer to the stack, which should be modified
after single stepping.
Currently, this instruction will be filtered as not
boostable in resume_execution(), so this is not a
critical issue.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David S . Miller <davem@davemloft.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ye Xiaolong <xiaolong.ye@intel.com> Link: http://lkml.kernel.org/r/149076340615.22469.14066273186134229909.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
sg_remove_sfp_usercontext() is clearing any sg requests, but needs to
take 'rq_list_lock' when modifying the list.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
projects / thirdparty / kernel / stable.git / log
