Fix the error path in free_dqentry(), pass out the error number if the
block to free is not correct.
Fixes: 1ccd14b9c271 ("quota: Split off quota tree handling into a separate file") Link: https://lore.kernel.org/r/20211008093821.1001186-3-yi.zhang@huawei.com Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Cc: stable@kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
In commit 411cef6adfb3 ("ALSA: mixer: oss: Fix racy access to slots")
added mutex protection in snd_mixer_oss_set_volume(). Second
mutex_lock() in same function looks like typo, fix it.
The OSS mixer can reassign the mapping slots dynamically via proc
file. Although the addition and deletion of those slots are protected
by mixer->reg_mutex, the access to slots aren't, hence this may cause
UAF when the slots in use are deleted concurrently.
This patch applies the mixer->reg_mutex in all appropriate code paths
(i.e. the ioctl functions) that may access slots.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b154 ("power_supply: Add MAX17042 Fuel Gauge Driver") Cc: <stable@vger.kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de> Signed-off-by: Henrik Grimler <henrik@grimler.se> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC") Cc: <stable@vger.kernel.org> Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 241b128b6b69 ("ath6kl: add back beginnings of USB support") Cc: stable@vger.kernel.org # 3.4 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211025120522.6045-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee358687e ("ath6kl: add full USB support") Cc: stable@vger.kernel.org # 3.5 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe354366 ("mwifiex: add support for Marvell USB8797 chipset") Cc: stable@vger.kernel.org # 3.5 Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The computation of TOHM is off by one bit. This missed bit results in
too low a value for TOHM, which can cause errors in regular memory to
incorrectly report:
EDAC MC0: 1 CE Error at MMIOH area, on addr 0x000000207fffa680 on any memory
Fixes: 50d1bb93672f ("sb_edac: add support for Haswell based systems") Cc: stable@vger.kernel.org Reported-by: Meeta Saggi <msaggi@purestorage.com> Signed-off-by: Eric Badger <ebadger@purestorage.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/r/20211010170127.848113-1-ebadger@purestorage.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The netif_device_detach() conditionally stops all tx queues if the queues
are running. There is no need to call netif_tx_stop_all_queues() again.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are missing braces in the function that verify controller parameters,
then an error is always returned when the parameter to select Microwire
frames operation is used on devices allowing it.
The tx queues are not stopped during the live migration. As a result, the
ndo_start_xmit() may access netfront_info->queues which is freed by
talk_to_netback()->xennet_destroy_queues().
This patch is to netif_device_detach() at the beginning of xen-netfront
resuming, and netif_device_attach() at the end of resuming.
CPU A CPU B
talk_to_netback()
-> if (info->queues)
xennet_destroy_queues(info);
to free netfront_info->queues
xennet_start_xmit()
to access netfront_info->queues
-> err = xennet_create_queues(info, &num_queues);
The idea is borrowed from virtio-net.
Cc: Joe Jin <joe.jin@oracle.com> Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes: f6b3c72c2366 ("x86/irq: Define a global vector for VT-d Posted-Interrupts") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009001107.3936588-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the previous fix (commit c0317c0e8709 "ALSA: timer: Fix
use-after-free problem"), we have to unlink slave timer instances
immediately at snd_timer_stop(), too. Otherwise it may leave a stale
entry in the list if the slave instance is freed before actually
running.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
If kcalloc() return NULL due to memory starvation, it is possible for
kstrdup() to return NULL in similar case. So add null check after the call
to kstrdup() is made.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
The TIF_XXX flags are stored in the flags field in the thread_info
struct (TI_FLAGS), not in the flags field of the task_struct structure
(TASK_FLAGS).
It seems this bug didn't generate any important side-effects, otherwise it
wouldn't have went unnoticed for 12 years (since v2.6.32).
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Patch series "ocfs2: Truncate data corruption fix".
As further testing has shown, commit 5314454ea3f ("ocfs2: fix data
corruption after conversion from inline format") didn't fix all the data
corruption issues the customer started observing after 6dbf7bb55598
("fs: Don't invalidate page buffers in block_write_full_page()") This
time I have tracked them down to two bugs in ocfs2 truncation code.
One bug (truncating page cache before clearing tail cluster and setting
i_size) could cause data corruption even before 6dbf7bb55598, but before
that commit it needed a race with page fault, after 6dbf7bb55598 it
started to be pretty deterministic.
Another bug (zeroing pages beyond old i_size) used to be harmless
inefficiency before commit 6dbf7bb55598. But after commit 6dbf7bb55598
in combination with the first bug it resulted in deterministic data
corruption.
Although fixing only the first problem is needed to stop data
corruption, I've fixed both issues to make the code more robust.
This patch (of 2):
ocfs2_truncate_file() did unmap invalidate page cache pages before
zeroing partial tail cluster and setting i_size. Thus some pages could
be left (and likely have left if the cluster zeroing happened) in the
page cache beyond i_size after truncate finished letting user possibly
see stale data once the file was extended again. Also the tail cluster
zeroing was not guaranteed to finish before truncate finished causing
possible stale data exposure. The problem started to be particularly
easy to hit after commit 6dbf7bb55598 "fs: Don't invalidate page buffers
in block_write_full_page()" stopped invalidation of pages beyond i_size
from page writeback path.
Fix these problems by unmapping and invalidating pages in the page cache
after the i_size is reduced and tail cluster is zeroed out.
Link: https://lkml.kernel.org/r/20211025150008.29002-1-jack@suse.cz Link: https://lkml.kernel.org/r/20211025151332.11301-1-jack@suse.cz Fixes: ccd979bdbce9 ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d4a ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since binder was integrated with selinux, it has passed
'struct task_struct' associated with the binder_proc
to represent the source and target of transactions.
The conversion of task to SID was then done in the hook
implementations. It turns out that there are race conditions
which can result in an incorrect security context being used.
Fix by using the 'struct cred' saved during binder_open and pass
it to the selinux subsystem.
Cc: stable@vger.kernel.org # 5.14 (need backport for earlier stables) Fixes: 79af73079d75 ("Add security hooks to binder and implement the hooks for SELinux.") Suggested-by: Jann Horn <jannh@google.com> Signed-off-by: Todd Kjos <tkjos@google.com> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the 'struct cred' associated with a binder process
at initial open to avoid potential race conditions
when converting to an euid.
Set a transaction's sender_euid from the 'struct cred'
saved at binder_open() instead of looking up the euid
from the binder proc's 'struct task'. This ensures
the euid is associated with the security context that
of the task that opened binder.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Cc: stable@vger.kernel.org # 2.6.37 Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211025120910.6339-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bulk and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.
Note that the bulk-out transfer timeout was set to the endpoint
bInterval value, which should be ignored for bulk endpoints and is
typically set to zero. This meant that a failing bulk-out transfer
would never time out.
Assume that the 10 second timeout used for all other transfers is more
than enough also for the bulk-out endpoint.
Fixes: 985cafccbf9b ("Staging: Comedi: vmk80xx: Add k8061 support") Fixes: 951348b37738 ("staging: comedi: vmk80xx: wait for URBs to complete") Cc: stable@vger.kernel.org # 2.6.31 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20211025114532.4599-6-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using endpoint-sized buffers but must not assume that the
tx and rx buffers are of equal size or a malicious device could overflow
the slab-allocated receive buffer when doing bulk transfers.
The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.
Commit e1f13c879a7c ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.
Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.
The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize.
The driver uses endpoint-sized USB transfer buffers but had no sanity
checks on the sizes. This can lead to zero-size-pointer dereferences or
overflowed transfer buffers in ni6501_port_command() and
ni6501_counter_command() if a (malicious) device has smaller max-packet
sizes than expected (or when doing descriptor fuzz testing).
Add the missing sanity checks to probe().
Fixes: a03bb00e50ab ("staging: comedi: add NI USB-6501 support") Cc: stable@vger.kernel.org # 3.18 Cc: Luca Ellero <luca.ellero@brickedbrain.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211027093529.30896-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.
Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.
Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is.
Fixes: 63274cd7d38a ("Staging: comedi: add usb dt9812 driver") Cc: stable@vger.kernel.org # 2.6.29 Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211027093529.30896-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When isofs image is suitably corrupted isofs_read_inode() can read data
beyond the end of buffer. Sanity-check the directory entry length before
using it.
Reported-and-tested-by: syzbot+6fc7fb214625d82af7d1@syzkaller.appspotmail.com CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com Fixes: 5fcfb6d0bfcd ("hso: fix bailout in error case of probe") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 48021f98130880dd74 ("printk: handle blank console arguments
passed in.") prevented crash caused by empty console= parameter value.
Unfortunately, this value is widely used on Chromebooks to disable
the console output. The above commit caused performance regression
because the messages were pushed on slow console even though nobody
was watching it.
Use ttynull driver explicitly for console="" and console=null
parameters. It has been created for exactly this purpose.
It causes that preferred_console is set. As a result, ttySX and ttyX
are not used as a fallback. And only ttynull console gets registered by
default.
It still allows to register other consoles either by additional console=
parameters or SPCR. It prevents regression because it worked this way even
before. Also it is a sane semantic. Preventing output on all consoles
should be done another way, for example, by introducing mute_console
parameter.
These drive enclosures have firmware bugs that make it impossible to mount
a new virtual ISO image after Linux ejects the old one if the device is
locked by Linux. Windows bypasses this problem by the fact that they do
not lock the device. Add a quirk to disable device locking for these
drive enclosures.
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Overflowing either addrlimit or bytes_togo can allow userspace to trigger
a buffer overflow of kernel memory. Check for overflows in all the places
doing math on user controlled buffers.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Link: https://lore.kernel.org/r/20211012175519.7298.77738.stgit@awfm-01.cornelisnetworks.com Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*pkt) + sizeof(pkt->addr[0])*n
with:
struct_size(pkt, addr, n)
Also, notice that variable size is unnecessary, hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the netdev is accessed before the urbs are initialized,
there will be NULL pointer dereferences. That is avoided by
registering it when it is fully initialized.
This case occurs e.g. if dhcpcd is running in the background
and the device is probed, either after insmod hso or
when the device appears on the usb bus.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 77a7300abad7 ("of/irq: Get rid of NO_IRQ usage"),
no irq case has been removed, irq_of_parse_and_map() will return
0 in all cases when get error from parse and map an interrupt into
linux virq space.
amba_device_register() is only used on no-DT initialization, see
s3c64xx_pl080_init() arch/arm/mach-s3c/pl080.c
ep93xx_init_devices() arch/arm/mach-ep93xx/core.c
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCSI host release is triggered when SCSI device is freed. We have to make
sure that the low-level device driver module won't be unloaded before SCSI
host instance is released because shost->hostt is required in the release
handler.
Make sure to put LLD module refcnt after SCSI device is released.
Fixes a kernel panic of 'BUG: unable to handle page fault for address'
reported by Changhui and Yi.
Link: https://lore.kernel.org/r/20211008050118.1440686-1-ming.lei@redhat.com Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Changhui Zhong <czhong@redhat.com> Reported-by: Yi Zhang <yi.zhang@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp_sf_violation() is called when processing HEARTBEAT_ACK chunk
in cookie_wait state, and some other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently Linux SCTP uses the verification tag of the existing SCTP
asoc when failing to process and sending the packet with the ABORT
chunk. This will result in the peer accepting the ABORT chunk and
removing the SCTP asoc. One could exploit this to terminate a SCTP
asoc.
This patch is to fix it by always using the initiate tag of the
received INIT chunk for the ABORT chunk to be sent.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
make[1]: *** No rule to make target 'arch/nios2/boot/dts/""',
needed by 'arch/nios2/boot/dts/built-in.a'. Stop.
make: [Makefile:1868: arch/nios2/boot/dts] Error 2 (ignored)
This is seen with compile tests since those enable NIOS2_DTB_SOURCE_BOOL,
which in turn enables NIOS2_DTB_SOURCE. This causes the build error
because the default value for NIOS2_DTB_SOURCE is an empty string.
Disable NIOS2_DTB_SOURCE_BOOL for compile tests to avoid the error.
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 3f4ff561bc88b ("regmap: rbtree: Make cache_present bitmap per node") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: stable@vger.kernel.org # 4.3 Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.
Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
During probing, the driver tries to get a list (mask) of supported
command types in port100_get_command_type_mask() function. The value
is u64 and 0 is treated as invalid mask (no commands supported). The
function however returns also -ERRNO as u64 which will be interpret as
valid command mask.
Return 0 on every error case of port100_get_command_type_mask(), so the
probing will stop.
Cc: <stable@vger.kernel.org> Fixes: 0347a6ab300a ("NFC: port100: Commands mechanism implementation") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return error code if usb_maxpacket() returns 0 in usbnet_probe()
Fixes: 397430b50a36 ("usbnet: sanity check for maxpacket") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211026124015.3025136-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been a no-op in binutils since 2004 (see commit dea514f51da1 in
that tree). Given that the lowest officially supported of binutils for
the kernel is 2.20, which was released in 2009, nobody needs this flag
around so just remove it. Commit 1a381d4a0a9a ("arm64: remove no-op -p
linker flag") did the same for arm64.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With extra warnings enabled, gcc complains about this function
definition:
arch/arm/probes/kprobes/core.c: In function 'arch_init_kprobes':
arch/arm/probes/kprobes/core.c:465:12: warning: old-style function definition [-Wold-style-definition]
465 | int __init arch_init_kprobes()
Both the decompressor code and the kasan logic try to override
the memcpy() and memmove() definitions, which leading to a clash
in a KASAN-enabled kernel with XZ decompression:
A kernel built with CONFIG_THUMB2_KERNEL=y and using clang as the
assembler could generate non-naturally-aligned v7wbi_tlb_fns which
results in a boot failure. The original commit adding the macro missed
the .align directive on this data.
tglx notes:
This function [futex_detect_cmpxchg] is only needed when an
architecture has to runtime discover whether the CPU supports it or
not. ARM has unconditional support for this, so the obvious thing to
do is the below.
Fixes linkage failure from Clang randconfigs:
kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text'
and boot failures for CONFIG_THUMB2_KERNEL.
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/ Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com> Cc: Helge Deller <deller@gmx.de> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Jisheng Zhang <jszhang@kernel.org> Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com> Cc: Guo Ren <guoren@kernel.org> Cc: stable@vger.kernel.org Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5ed ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449be ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org> Cc: Benson Leung <bleung@chromium.org> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During this process, the kernel thread would call detach_capi_ctr()
to detach a register controller. if the controller
was not attached yet, detach_capi_ctr() would
trigger an array-index-out-bounds bug.
[ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in
drivers/isdn/capi/kcapi.c:483:21
[ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]'
[ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted
5.15.0-rc2+ #8
[ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX,
1996), BIOS 1.14.0-2 04/01/2014
[ 46.870107][ T6479] Call Trace:
[ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d
[ 46.870974][ T6479] ubsan_epilogue+0x5/0x40
[ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48
[ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0
[ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0
[ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60
[ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120
[ 46.874256][ T6479] kthread+0x147/0x170
[ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40
[ 46.875248][ T6479] ret_from_fork+0x1f/0x30
[ 46.875773][ T6479]
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put callback of a kcontrol is supposed to return 1 when the value
is changed, and this will be notified to user-space. However, some
DAPM kcontrols always return 0 (except for errors), hence the
user-space misses the update of a control value.
This patch corrects the behavior by properly returning 1 when the
value gets updated.
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13
The GSP670 has 2 playback and 1 recording device that by default are
detected in an incompatible order for alsa. This may have been done to make
it compatible for the console by the manufacturer and only affects the
latest firmware which uses its own ID.
This quirk will resolve this by reordering the channels.
Commit 6e7b64b9dd6d ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an
ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the
trace below. Problem seems to be that strings for cluster stack and
cluster name are not guaranteed to be null terminated in the disk
representation, while strlcpy assumes that the source string is always
null terminated. This causes a read outside of the source string
triggering the buffer overflow detection.
Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both arch/nios2/ and drivers/mmc/host/tmio_mmc.c define a macro
with the name "CTL_STATUS". Change the one in arch/nios2/ to be
"CTL_FSTATUS" (flags status) to eliminate the build warning.
In file included from ../drivers/mmc/host/tmio_mmc.c:22:
drivers/mmc/host/tmio_mmc.h:31: warning: "CTL_STATUS" redefined
31 | #define CTL_STATUS 0x1c
arch/nios2/include/asm/registers.h:14: note: this is the location of the previous definition
14 | #define CTL_STATUS 0
If nfsd has existing listening sockets without any processes, then an error
returned from svc_create_xprt() for an additional transport will remove
those existing listeners. We're seeing this in practice when userspace
attempts to create rpcrdma transports without having the rpcrdma modules
present before creating nfsd kernel processes. Fix this by checking for
existing sockets before calling nfsd_destroy().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a2a1 ("r8152: support request_firmware for RTL8153") Fixes: ac718b69301c7 ("net/usb: new driver for RTL8152") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initialization of pointer dev dereferences pointer edp before
edp is null checked, so there is a potential null pointer deference
issue. Fix this by only dereferencing edp after edp has been null
checked.
Addresses-Coverity: ("Dereference before null check") Fixes: ab5b0107ccf3 ("drm/msm: Initial add eDP support in msm drm driver (v5)") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210929121857.213922-1-colin.king@canonical.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
