With CONFIG_GENDWARFKSYMS, __gendwarfksyms_ptr variables are
added to the kernel in EXPORT_SYMBOL() to ensure DWARF type
information is available for exported symbols in the TUs where
they're actually exported. These symbols are dropped when linking
vmlinux, but dangling references to them remain in DWARF.
With CONFIG_DEBUG_INFO_BTF enabled on X86, pahole versions after
commit 47dcb534e253 ("btf_encoder: Stop indexing symbols for
VARs") and before commit 9810758003ce ("btf_encoder: Verify 0
address DWARF variables are in ELF section") place these symbols
in the .data..percpu section, which results in an "Invalid
offset" error in btf_datasec_check_meta() during boot, as all
the variables are at zero offset and have non-zero size. If
CONFIG_DEBUG_INFO_BTF_MODULES is enabled, this also results in a
failure to load modules with:
failed to validate module [$module] BTF: -22
As the issue occurs in pahole v1.28 and the fix was merged
after v1.29 was released, require pahole <v1.28 or >v1.29 when
GENDWARFKSYMS is enabled with DEBUG_INFO_BTF on X86.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change get_thinkpad_model_data() to check for additional vendor name
"NEC" in order to support NEC Lavie X1475JAS notebook (and perhaps
more).
The reason of this works with minimal changes is because NEC Lavie
X1475JAS is a Thinkpad inside. ACPI dumps reveals its OEM ID to be
"LENOVO", BIOS version "R2PET30W" matches typical Lenovo BIOS version,
the existence of HKEY of LEN0268, with DMI fw string is "R2PHT24W".
I compiled and tested with my own machine, attached the dmesg
below as proof of work:
[ 6.288932] thinkpad_acpi: ThinkPad ACPI Extras v0.26
[ 6.288937] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 6.288938] thinkpad_acpi: ThinkPad BIOS R2PET30W (1.11 ), EC R2PHT24W
[ 6.307000] thinkpad_acpi: radio switch found; radios are enabled
[ 6.307030] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[ 6.307033] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[ 6.320322] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 6.371963] thinkpad_acpi: secondary fan control detected & enabled
[ 6.391922] thinkpad_acpi: battery 1 registered (start 0, stop 85, behaviours: 0x7)
[ 6.398375] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input13
Signed-off-by: John Chau <johnchau@0atlas.com> Link: https://lore.kernel.org/r/20250504165513.295135-1-johnchau@0atlas.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, different NFS clients can share the same DS connections, even
when they are in different net namespaces. If a containerized client
creates a DS connection, another container can find and use it. When the
first client exits, the connection will close which can lead to stalls
in other clients.
Add a net namespace pointer to struct nfs4_pnfs_ds, and compare those
value to the caller's netns in _data_server_lookup_locked() when
searching for a nfs4_pnfs_ds to match.
This patch adds HID_QUIRK_ALWAYS_POLL for the ADATA XPG wireless gaming mouse (USB ID 125f:7505) and its USB dongle (USB ID 125f:7506). Without this quirk, the device does not generate input events properly.
Fix Smatch-detected issue:
drivers/dma/idxd/cdev.c:321 idxd_cdev_open() error:
uninitialized symbol 'sva'.
'sva' pointer may be used uninitialized in error handling paths.
Specifically, if PASID support is enabled and iommu_sva_bind_device()
returns an error, the code jumps to the cleanup label and attempts to
call iommu_sva_unbind_device(sva) without ensuring that sva was
successfully assigned. This triggers a Smatch warning about an
uninitialized symbol.
Initialize sva to NULL at declaration and add a check using
IS_ERR_OR_NULL() before unbinding the device. This ensures the
function does not use an invalid or uninitialized pointer during
cleanup.
Give userspace a way to instruct the kernel to install a pidfd into the
usermode helper process. This makes coredump handling a lot more
reliable for userspace. In parallel with this commit we already have
systemd adding support for this in [1].
We create a pidfs file for the coredumping process when we process the
corename pattern. When the usermode helper process is forked we then
install the pidfs file as file descriptor three into the usermode
helpers file descriptor table so it's available to the exec'd program.
Since usermode helpers are either children of the system_unbound_wq
workqueue or kthreadd we know that the file descriptor table is empty
and can thus always use three as the file descriptor number.
Note, that we'll install a pidfd for the thread-group leader even if a
subthread is calling do_coredump(). We know that task linkage hasn't
been removed due to delay_group_leader() and even if this @current isn't
the actual thread-group leader we know that the thread-group leader
cannot be reaped until @current has exited.
[brauner: This is a backport for the v6.12 series. The upstream kernel
has changed pidfs_alloc_file() to set O_RDWR implicitly instead of
forcing callers to set it. Let's minimize the churn and just let the
coredump umh handler raise O_RDWR.]
The replace_fd() helper returns the file descriptor number on success
and a negative error code on failure. The current error handling in
umh_pipe_setup() only works because the file descriptor that is replaced
is zero but that's pretty volatile. Explicitly check for a negative
error code.
Next up on our list of race windows to close is another one during
iommu_device_register() - it's now OK again for multiple instances to
run their bus_iommu_probe() in parallel, but an iommu_probe_device() can
still also race against a running bus_iommu_probe(). As Johan has
managed to prove, this has now become a lot more visible on DT platforms
wth driver_async_probe where a client driver is attempting to probe in
parallel with its IOMMU driver - although commit b46064a18810 ("iommu:
Handle race with default domain setup") resolves this from the client
driver's point of view, this isn't before of_iommu_configure() has had
the chance to attempt to "replay" a probe that the bus walk hasn't even
tried yet, and so still cause the out-of-order group allocation
behaviour that we're trying to clean up (and now warning about).
The most reliable thing to do here is to explicitly keep track of the
"iommu_device_register() is still running" state, so we can then
special-case the ops lookup for the replay path (based on dev->iommu
again) to let that think it's still waiting for the IOMMU driver to
appear at all. This still leaves the longstanding theoretical case of
iommu_bus_notifier() being triggered during bus_iommu_probe(), but it's
not so simple to defer a notifier, and nobody's ever reported that being
a visible issue, so let's quietly kick that can down the road for now...
An ACPI binding for CMN S3 was not yet finalised when the driver support
was originally written, but v1.2 of DEN0093 "ACPI for Arm Components"
has at last been published; support ACPI systems using the proper HID.
For all the complexity of handling affinity for CPU hotplug, what we've
apparently managed to overlook is that arm_cmn_init_irqs() has in fact
always been setting the *initial* affinity of all IRQs to CPU 0, not the
CPU we subsequently choose for event scheduling. Oh dear.
Cc: stable@vger.kernel.org Fixes: 0ba64770a2f2 ("perf: Add Arm CMN-600 PMU driver") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com> Link: https://lore.kernel.org/r/b12fccba6b5b4d2674944f59e4daad91cd63420b.1747069914.git.robin.murphy@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Savino says:
"We are writing to report that this recent patch
(141d34391abbb315d68556b7c67ad97885407547) [1]
can be bypassed, and a UAF can still occur when HFSC is utilized with
NETEM.
The patch only checks the cl->cl_nactive field to determine whether
it is the first insertion or not [2], but this field is only
incremented by init_vf [3].
By using HFSC_RSC (which uses init_ed) [4], it is possible to bypass the
check and insert the class twice in the eltree.
Under normal conditions, this would lead to an infinite loop in
hfsc_dequeue for the reasons we already explained in this report [5].
However, if TBF is added as root qdisc and it is configured with a
very low rate,
it can be utilized to prevent packets from being dequeued.
This behavior can be exploited to perform subsequent insertions in the
HFSC eltree and cause a UAF."
To fix both the UAF and the infinite loop, with netem as an hfsc child,
check explicitly in hfsc_enqueue whether the class is already in the eltree
whenever the HFSC_RSC flag is set.
Commit under Fixes corrected the "mux-reg-masks" property but did not
update the "length" field of the "reg" property to account for the
newly added register offsets which extend the region. Fix this.
Since "serdes0" and "serdes1" which are the sub-nodes of "serdes_wiz0"
and "serdes_wiz1" respectively, have been disabled in the SoC file already,
and, given that these sub-nodes will only be enabled in a board file if the
board utilizes any of the SERDES instances and the peripherals bound to
them, we end up in a situation where the board file doesn't explicitly
disable "serdes_wiz0" and "serdes_wiz1". As a consequence of this, the
following errors show up when booting Linux:
wiz bus@f0000:phy@f000000: probe with driver wiz failed with error -12
...
wiz bus@f0000:phy@f010000: probe with driver wiz failed with error -12
To not only fix the above, but also, in order to follow the convention of
disabling device-tree nodes in the SoC file and enabling them in the board
files for those boards which require them, disable "serdes_wiz0" and
"serdes_wiz1" device-tree nodes.
In preparation for disabling "serdes_wiz0" and "serdes_wiz1" device-tree
nodes in the SoC file, enable them in the board file. The motivation for
this change is that of following the existing convention of disabling
nodes in the SoC file and only enabling the required ones in the board
file.
Fixes: 485705df5d5f ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM") Cc: stable@vger.kernel.org Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20250417123246.2733923-2-s-vadapalli@ti.com Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device tree overlay for the IMX219 sensor requires three voltage
supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
(digital I/O). Add the corresponding voltage supply definitions to
avoid dtbs_check warnings.
The IMX219 sensor device tree bindings do not include a clock-names
property. Remove the incorrectly added clock-names entry to avoid
dtbs_check warnings.
Add device tree nodes for two power regulators on the J721E SK board.
vsys_5v0: A fixed regulator representing the 5V supply output from the
LM61460 and vdd_sd_dv: A GPIO-controlled TLV71033 regulator.
Update the vin-supply of the TLV71033 regulator from LM5141 (vsys_3v3)
to LM61460 (vsys_5v0) to match the schematics. Add a fixed regulator
node for the LM61460 5V supply to support this change.
The OV5640 device tree overlay incorrectly defined an I2C switch
instead of an I2C mux. According to the DT bindings, the correct
terminology and node definition should use "i2c-mux" instead of
"i2c-switch". Hence, update the same to avoid dtbs_check warnings.
The IMX219 device tree overlay incorrectly defined an I2C switch
instead of an I2C mux. According to the DT bindings, the correct
terminology and node definition should use "i2c-mux" instead of
"i2c-switch". Hence, update the same to avoid dtbs_check warnings.
The IMX219 sensor device tree bindings do not include a clock-names
property. Remove the incorrectly added clock-names entry to avoid
dtbs_check warnings.
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.
Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A passive trip point at 125°C is pretty high, this is usually the
temperature for the critical shutdown trip point. Also, we don't have any
passive cooling devices attached to the video thermal zone.
Change this to be a critical trip point, and add a "hot" trip point at
90°C for consistency with the other thermal zones.
Cc: stable@vger.kernel.org Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-1-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-6-24b6a2043025@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org Fixes: 45247fe17db2 ("arm64: dts: qcom: x1e80100: add Lenovo Thinkpad Yoga slim 7x devicetree") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-5-24b6a2043025@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org Fixes: 6f18b8d4142c ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-4-24b6a2043025@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d37e2646c8a5 ("arm64: dts: qcom: x1e80100-pmics: Enable all SMB2360
separately") disables all SMB2360s and let the board DTS explicitly enable
them. The HP OmniBook DTS is from before this change and is missing the
explicit enabling. Add that to get all USB root ports.
Fixes: 6f18b8d4142c ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14") Cc: stable@vger.kernel.org # 6.14 Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/r/20250319160509.1812805-1-juerg.haefliger@canonical.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org Fixes: d0e2f8f62dff ("arm64: dts: qcom: Add device tree for ASUS Vivobook S 15") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-3-24b6a2043025@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org Fixes: 7b8a31e82b87 ("arm64: dts: qcom: Add X1E001DE Snapdragon Devkit for Windows") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-2-24b6a2043025@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
num-channels and qcom,num-ees are required for BAM nodes without clock,
because the driver cannot ensure the hardware is powered on when trying to
obtain the information from the hardware registers. Specifying the node
without these properties is unsafe and has caused early boot crashes for
other SoCs before [1, 2].
Add the missing information from the hardware registers to ensure the
driver can probe successfully without causing crashes.
num-channels and qcom,num-ees are required for BAM nodes without clock,
because the driver cannot ensure the hardware is powered on when trying to
obtain the information from the hardware registers. Specifying the node
without these properties is unsafe and has caused early boot crashes for
other SoCs before [1, 2].
Add the missing information from the hardware registers to ensure the
driver can probe successfully without causing crashes.
num-channels and qcom,num-ees are required for BAM nodes without clock,
because the driver cannot ensure the hardware is powered on when trying to
obtain the information from the hardware registers. Specifying the node
without these properties is unsafe and has caused early boot crashes for
other SoCs before [1, 2].
Add the missing information from the hardware registers to ensure the
driver can probe successfully without causing crashes.
There is a typo in sm8350.dts where the node label
mmeory@85200000 should be memory@85200000.
This patch corrects the typo for clarity and consistency.
num-channels and qcom,num-ees are required for BAM nodes without clock,
because the driver cannot ensure the hardware is powered on when trying to
obtain the information from the hardware registers. Specifying the node
without these properties is unsafe and has caused early boot crashes for
other SoCs before [1, 2].
Add the missing information from the hardware registers to ensure the
driver can probe successfully without causing crashes.
num-channels and qcom,num-ees are required for BAM nodes without clock,
because the driver cannot ensure the hardware is powered on when trying to
obtain the information from the hardware registers. Specifying the node
without these properties is unsafe and has caused early boot crashes for
other SoCs before [1, 2].
Add the missing information from the hardware registers to ensure the
driver can probe successfully without causing crashes.
Currently, the onboard Cypress CYUSB3304 USB hub is not defined in
the device tree, and hub reset pin is provided as vcc5v0_host
regulator to usb phy. This causes instability issues, as a result
of improper reset duration.
The fixed regulator device requests the GPIO during probe in its
inactive state (except if regulator-boot-on property is set, in
which case it is requested in the active state). Considering gpio
is GPIO_ACTIVE_LOW for Puma, it means it’s driving it high. Then
the regulator gets enabled (because regulator-always-on property),
which drives it to its active state, meaning driving it low.
The Cypress CYUSB3304 USB hub actually requires the reset to be
asserted for at least 5 ms, which we cannot guarantee right now
since there's no delay in the current config, meaning the hub may
sometimes work or not. We could add delay as offered by
fixed-regulator but let's rather fix this by using the proper way
to model onboard USB hubs.
Define hub_2_0 and hub_3_0 nodes, as the onboard Cypress hub
consist of two 'logical' hubs, for USB2.0 and USB3.0.
Use the 'reset-gpios' property of hub to assign reset pin instead
of using regulator. Rename the vcc5v0_host regulator to
cy3304_reset to be more meaningful. Pin is configured to
output-high by default, which sets the hub in reset state
during pin controller initialization. This allows to avoid double
enumeration of devices in case the bootloader has setup the USB
hub before the kernel.
The vdd-supply and vdd2-supply properties in hub nodes are
added to provide correct dt-bindings, although power supplies are
always enabled based on HW design.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM") Cc: stable@vger.kernel.org # 6.6 Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com> Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-3-4a76a474a010@thaumatec.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid the driver missing IRQs by temporarily masking IRQs in the ISR
to enforce an edge even if a different IRQ is signalled before handled
IRQs are cleared.
Fixes: 48f827d4f48f ("can: kvaser_pciefd: Move reset of DMA RX buffers to the end of the ISR") Cc: stable@vger.kernel.org Signed-off-by: Axel Forsman <axfo@kvaser.com> Tested-by: Jimmy Assarsson <extja@kvaser.com> Reviewed-by: Jimmy Assarsson <extja@kvaser.com> Link: https://patch.msgid.link/20250520114332.8961-2-axfo@kvaser.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250527162513.035720581@linuxfoundation.org Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Tested-by: Ronald Warsow <rwarsow@gmx.de> Tested-by: Ron Economos <re@w6rz.net> Tested-by: Christian Heusel <christian@heusel.eu> Tested-by: Mark Brown <broonie@kernel.org> Tested-by: Markus Reichelt <lkt+2023@mareichelt.com> Tested-by: Justin M. Forbes <jforbes@fedoraproject.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang and GCC have different behaviors around disabling warnings
included in -Wall and -Wextra and the order in which flags are
specified, which is exposed by clang's new support for
-Wunterminated-string-initialization.
$ clang -fsyntax-only -Wextra test.c
test.c:1:21: warning: initializer-string for character array is too long, array size is 3 but initializer has size 4 (including the null terminating character); did you mean to use the 'nonstring' attribute? [-Wunterminated-string-initialization]
1 | const char foo[3] = "FOO";
| ^~~~~
$ clang -fsyntax-only -Wextra -Wno-unterminated-string-initialization test.c
$ clang -fsyntax-only -Wno-unterminated-string-initialization -Wextra test.c
test.c:1:21: warning: initializer-string for character array is too long, array size is 3 but initializer has size 4 (including the null terminating character); did you mean to use the 'nonstring' attribute? [-Wunterminated-string-initialization]
1 | const char foo[3] = "FOO";
| ^~~~~
Move -Wextra up right below -Wall in Makefile.extrawarn to ensure these
flags are at the beginning of the warning options list. Move the couple
of warning options that have been added to the main Makefile since
commit e88ca24319e4 ("kbuild: consolidate warning flags in
scripts/Makefile.extrawarn") to scripts/Makefile.extrawarn after -Wall /
-Wextra to ensure they get properly disabled for all compilers.
This was triggered by one of my mis-uses causing odd build warnings on
sparc in linux-next, but while figuring out why the "obviously correct"
use of cc-option caused such odd breakage, I found eight other cases of
the same thing in the tree.
The root cause is that 'cc-option' doesn't work for checking negative
warning options (ie things like '-Wno-stringop-overflow') because gcc
will silently accept options it doesn't recognize, and so 'cc-option'
ends up thinking they are perfectly fine.
And it all works, until you have a situation where _another_ warning is
emitted. At that point the compiler will go "Hmm, maybe the user
intended to disable this warning but used that wrong option that I
didn't recognize", and generate a warning for the unrecognized negative
option.
Which explains why we have several cases of this in the tree: the
'cc-option' test really doesn't work for this situation, but most of the
time it simply doesn't matter that ity doesn't work.
The reason my recently added case caused problems on sparc was pointed
out by Thomas Weißschuh: the sparc build had a previous explicit warning
that then triggered the new one.
I think the best fix for this would be to make 'cc-option' a bit smarter
about this sitation, possibly by adding an intentional warning to the
test case that then triggers the unrecognized option warning reliably.
But the short-term fix is to replace 'cc-option' with an existing helper
designed for this exact case: 'cc-disable-warning', which picks the
negative warning but uses the positive form for testing the compiler
support.
I had left the warning around but as a non-fatal error to get my gcc-15
builds going, but fixed up some of the most annoying warning cases so
that it wouldn't be *too* verbose.
Because I like the _concept_ of the warning, even if I detested the
implementation to shut it up.
It turns out the implementation to shut it up is even more broken than I
thought, and my "shut up most of the warnings" patch just caused fatal
errors on gcc-14 instead.
I had tested with clang, but when I upgrade my development environment,
I try to do it on all machines because I hate having different systems
to maintain, and hadn't realized that gcc-14 now had issues.
The ACPI case is literally why I wanted to have a *type* that doesn't
trigger the warning (see commit d5d45a7f2619: "gcc-15: make
'unterminated string initialization' just a warning"), instead of
marking individual places as "__nonstring".
But gcc-14 doesn't like that __nonstring location that shut gcc-15 up,
because it's on an array of char arrays, not on one single array:
drivers/acpi/tables.c:399:1: error: 'nonstring' attribute ignored on objects of type 'const char[][4]' [-Werror=attributes]
399 | static const char table_sigs[][ACPI_NAMESEG_SIZE] __initconst __nonstring = {
| ^~~~~~
and my attempts to nest it properly with a type had failed, because of
how gcc doesn't like marking the types as having attributes, only
symbols.
There may be some trick to it, but I was already annoyed by the bad
attribute design, now I'm just entirely fed up with it.
I wish gcc had a proper way to say "this type is a *byte* array, not a
string".
The obvious thing would be to distinguish between "char []" and an
explicitly signed "unsigned char []" (as opposed to an implicitly
unsigned char, which is typically an architecture-specific default, but
for the kernel is universal thanks to '-funsigned-char').
But any "we can typedef a 8-bit type to not become a string just because
it's an array" model would be fine.
But "__attribute__((nonstring))" is sadly not that sane model.
Reported-by: Chris Clayton <chris2553@googlemail.com> Fixes: 4b4bd8c50f48 ("gcc-15: acpi: sprinkle random '__nonstring' crumbles around") Fixes: d5d45a7f2619 ("gcc-15: make 'unterminated string initialization' just a warning") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[nathan: drivers/acpi diff dropped due to lack of 4b4bd8c50f48 in stable] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
and we use this all over the kernel. And the warning is fine, but gcc
developers apparently never made a reasonable way to disable it. As is
(sadly) tradition with these things.
Yes, there's "__attribute__((nonstring))", and we have a macro to make
that absolutely disgusting syntax more palatable (ie the kernel syntax
for that monstrosity is just "__nonstring").
But that attribute is misdesigned. What you'd typically want to do is
tell the compiler that you are using a type that isn't a string but a
byte array, but that doesn't work at all:
warning: ‘nonstring’ attribute does not apply to types [-Wattributes]
and because of this fundamental mis-design, you then have to mark each
instance of that pattern.
This is particularly noticeable in our ACPI code, because ACPI has this
notion of a 4-byte "type name" that gets used all over, and is exactly
this kind of byte array.
This is a sad oversight, because the warning is useful, but really would
be so much better if gcc had also given a sane way to indicate that we
really just want a byte array type at a type level, not the broken "each
and every array definition" level.
So now instead of creating a nice "ACPI name" type using something like
typedef char acpi_name_t[4] __nonstring;
we have to do things like
char name[ACPI_NAMESEG_SIZE] __nonstring;
in every place that uses this concept and then happens to have the
typical initializers.
This is annoying me mainly because I think the warning _is_ a good
warning, which is why I'm not just turning it off in disgust. But it is
hampered by this bad implementation detail.
[ And obviously I'm doing this now because system upgrades for me are
something that happen in the middle of the release cycle: don't do it
before or during travel, or just before or during the busy merge
window period. ]
On VCN v4.0.5 there is a race condition where the WPTR is not
updated after starting from idle when doorbell is used. Adding
register read-back after written at function end is to ensure
all register writes are done before they can be used.
Closes: https://gitlab.freedesktop.org/mesa/mesa/-/issues/12528 Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Ruijing Dong <ruijing.dong@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 07c9db090b86e5211188e1b351303fbc673378cf) Cc: stable@vger.kernel.org Tested-by: Eric Naim <dnaim@cachyos.org> Signed-off-by: Eric Naim <dnaim@cachyos.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Determining the SST/MST mode during state computation must be done based
on the output type stored in the CRTC state, which in turn is set once
based on the modeset connector's SST vs. MST type and will not change as
long as the connector is using the CRTC. OTOH the MST mode indicated by
the given connector's intel_dp::is_mst flag can change independently of
the above output type, based on what sink is at any moment plugged to
the connector.
Fix the state computation accordingly.
Cc: Jani Nikula <jani.nikula@intel.com> Fixes: f6971d7427c2 ("drm/i915/mst: adapt intel_dp_mtp_tu_compute_config() for 128b/132b SST") Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/4607 Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://lore.kernel.org/r/20250507151953.251846-1-imre.deak@intel.com
(cherry picked from commit 0f45696ddb2b901fbf15cb8d2e89767be481d59f) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
References: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14218
[Rebased on v6.14.8 and added References link. (Imre)] Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IOMEM_ERR_PTR() macro deals with an error pointer, a better place
for it is err.h. This helps avoid dependency on io.h for the users that
don't need it.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Raag Jadav <raag.jadav@intel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtcfg register is a 32-bit register and should therefore be
accessed using xe_mmio_read32().
Other 3 changes per codestyle suggestion:
"
xe_mmio.c:83: CHECK: Alignment should match open parenthesis
xe_mmio.c:131: CHECK: Comparison to NULL could be written "!xe->mmio.regs"
xe_mmio.c:315: CHECK: line length of 103 exceeds 100 columns
"
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs") Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com> Link: https://lore.kernel.org/r/20250513153010.3464767-1-shuicheng.lin@intel.com Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit d2662cf8f44a68deb6c76ad9f1d9f29dbf7ba601) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If, in a previous transfer, the controller sends more data than expected
by the DSPI target, SR.RFDF (RX FIFO is not empty) will remain asserted.
When flushing the FIFOs at the beginning of a new transfer (writing 1
into MCR.CLR_TXF and MCR.CLR_RXF), SR.RFDF should also be cleared.
Otherwise, when running in target mode with DMA, if SR.RFDF remains
asserted, the DMA callback will be fired before the controller sends any
data.
Take this opportunity to reset all Status Register fields.
Fixes: 5ce3cc567471 ("spi: spi-fsl-dspi: Provide support for DSPI slave mode operation (Vybryd vf610)") Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com> Signed-off-by: James Clark <james.clark@linaro.org> Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-3-bea884630cfb@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The XSPI mode implementation in this driver still uses the EOQ flag to
signal the last word in a transmission and deassert the PCS signal.
However, at speeds lower than ~200kHZ, the PCS signal seems to remain
asserted even when SR[EOQF] = 1 indicates the end of a transmission.
This is a problem for target devices which require the deassertation of
the PCS signal between transfers.
Hence, this commit 'forces' the deassertation of the PCS by stopping the
module through MCR[HALT] after completing a new transfer. According to
the reference manual, the module stops or transitions from the Running
state to the Stopped state after the current frame, when any one of the
following conditions exist:
- The value of SR[EOQF] = 1.
- The chip is in Debug mode and the value of MCR[FRZ] = 1.
- The value of MCR[HALT] = 1.
This shouldn't be done if the last transfer in the message has cs_change
set.
Fixes: ea93ed4c181b ("spi: spi-fsl-dspi: Use EOQ for last word in buffer even for XSPI mode") Signed-off-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@nxp.com> Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com> Signed-off-by: James Clark <james.clark@linaro.org> Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-2-bea884630cfb@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DSPI registers are NOT continuous, some registers are reserved and
accessing them from userspace will trigger external abort, add regmap
register access table to avoid below abort.
Fixes: 1acbdeb92c87 ("spi/fsl-dspi: Convert to use regmap and add big-endian support") Co-developed-by: Xulin Sun <xulin.sun@windriver.com> Signed-off-by: Xulin Sun <xulin.sun@windriver.com> Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com> Signed-off-by: James Clark <james.clark@linaro.org> Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-1-bea884630cfb@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some places in the spi core pass in a const pointer to a device and the
default container_of() casts that away, which is not a good idea.
Preserve the proper const attribute by using container_of_const() for
to_spi_device() instead, which is what it was designed for.
Note, this removes the NULL check for a device pointer in the call, but
no one was ever checking for that return value, and a device pointer
should never be NULL overall anyway, so this should be a safe change.
Cc: Mark Brown <broonie@kernel.org> Fixes: d69d80484598 ("driver core: have match() callback in struct bus_type take a const *") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://patch.msgid.link/2025052230-fidgeting-stooge-66f5@gregkh Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A few, quite rare, WMI attributes have names that are not compatible with
filenames, e.g. "Intel VT for Directed I/O (VT-d)".
For these cases the '/' gets replaced with '\' for display, but doesn't
get switched again when doing the WMI access.
Fix this by keeping the original attribute name and using that for sending
commands to the BIOS
Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms") Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20250520005027.3840705-1-mpearson-lenovo@squebb.ca Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is no stream data in file, v_len is zero.
So, If position(*pos) is zero, stream write will fail
due to stream write position validation check.
This patch reorganize stream write position validation.
Fixes: 0ca6df4f40cf ("ksmbd: prevent out-of-bounds stream writes by validating *pos") Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hardware that uses I2C wasn't designed with high speeds in mind, so
communication with PMIC via RSB can intermittently fail. Go back to I2C
as higher speed and efficiency isn't worth the trouble.
To prevent Bluetooth SDIO card from be physically removed suddenly,
driver needs to ensure btmtksdio_close is called before
btmtksdio_remove to disable interrupts and txrx workqueue.
Fixes: 6ac4233afb9a ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check BTMTKSDIO_FUNC_ENABLED flag before doing close to prevent
btmtksdio_close been called twice.
Fixes: 6ac4233afb9a ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c0e473a0d226 ("block: fix race between set_blocksize and read
paths") was merged, set_blocksize() called by sb_set_blocksize() now locks
the inode of the backing device file. As a result of this change, syzbot
started reporting deadlock warnings due to a circular dependency involving
the semaphore "ns_sem" of the nilfs object, the inode lock of the backing
device file, and the locks that this inode lock is transitively dependent
on.
This is caused by a new lock dependency added by the above change, since
init_nilfs() calls sb_set_blocksize() in the lock section of "ns_sem".
However, these warnings are false positives because init_nilfs() is called
in the early stage of the mount operation and the filesystem has not yet
started.
The reason why "ns_sem" is locked in init_nilfs() was to avoid a race
condition in nilfs_fill_super() caused by sharing a nilfs object among
multiple filesystem instances (super block structures) in the early
implementation. However, nilfs objects and super block structures have
long ago become one-to-one, and there is no longer any need to use the
semaphore there.
So, fix this issue by removing the use of the semaphore "ns_sem" in
init_nilfs().
A previous patch introduces a build-time warning when CONFIG_DCB
is disabled:
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c: In function 'otx2_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c:3217:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c: In function 'otx2vf_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c:740:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
The common case is to grow reallocations, and since init_on_alloc will
have already zeroed the whole allocation, we only need to zero when
shrinking the allocation.
On configs with CONFIG_ARM64_GCS=y, VM_SHADOW_STACK is bit 38. On configs
with CONFIG_HAVE_ARCH_USERFAULTFD_MINOR=y (selected by CONFIG_ARM64 when
CONFIG_USERFAULTFD=y), VM_UFFD_MINOR is _also_ bit 38.
This bit being shared by two different VMA flags could lead to all sorts
of unintended behaviors. Presumably, a process could maybe call into
userfaultfd in a way that disables the shadow stack vma flag. I can't
think of any attack where this would help (presumably, if an attacker
tries to disable shadow stacks, they are trying to hijack control flow so
can't arbitrarily call into userfaultfd yet anyway) but this still feels
somewhat scary.
Link: https://lkml.kernel.org/r/20250507131000.1204175-2-revest@chromium.org Fixes: ae80e1629aea ("mm: Define VM_SHADOW_STACK for arm64 when we support GCS") Signed-off-by: Florent Revest <revest@chromium.org> Reviewed-by: Mark Brown <broonie@kernel.org> Cc: Borislav Betkov <bp@alien8.de> Cc: Brendan Jackman <jackmanb@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Florent Revest <revest@chromium.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thiago Jung Bauermann <thiago.bauermann@linaro.org> Cc: Thomas Gleinxer <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4608d1bf7c6 ("mm: mmap: map MAP_STACK to VM_NOHUGEPAGE") maps the
mmap option MAP_STACK to VM_NOHUGEPAGE. This is also done if
CONFIG_TRANSPARENT_HUGEPAGE is not defined. But in that case, the
VM_NOHUGEPAGE does not make sense.
I discovered this issue when trying to use the tool CRIU to checkpoint and
restore a container. Our running kernel is compiled without
CONFIG_TRANSPARENT_HUGEPAGE. CRIU parses the output of /proc/<pid>/smaps
and saves the "nh" flag. When trying to restore the container, CRIU fails
to restore the "nh" mappings, since madvise() MADV_NOHUGEPAGE always
returns an error because CONFIG_TRANSPARENT_HUGEPAGE is not defined.
Link: https://lkml.kernel.org/r/20250507-map-map_stack-to-vm_nohugepage-only-if-thp-is-enabled-v5-1-c6c38cfefd6e@kuka.com Fixes: c4608d1bf7c6 ("mm: mmap: map MAP_STACK to VM_NOHUGEPAGE") Signed-off-by: Ignacio Moreno Gonzalez <Ignacio.MorenoGonzalez@kuka.com> Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Reviewed-by: Yang Shi <yang@os.amperecomputing.com> Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem
========
commit 658eb5ab916d ("delayacct: add delay max to record delay peak")
- adding more fields
commit f65c64f311ee ("delayacct: add delay min to record delay peak")
- adding more fields
commit b016d0873777 ("taskstats: modify taskstats version")
- version bump to 15
Since version 15 (TASKSTATS_VERSION=15) the new layout of the structure
adds fields in the middle of the structure, rendering all old software
incompatible with newer kernels and software compiled against the new
kernel headers incompatible with older kernels.
Solution
=========
move delay max and delay min to the end of taskstat, and bump
the version to 16 after the change
[wang.yaxin@zte.com.cn: adjust indentation] Link: https://lkml.kernel.org/r/202505192131489882NSciXV4EGd8zzjLuwoOK@zte.com.cn Link: https://lkml.kernel.org/r/20250510155413259V4JNRXxukdDgzsaL0Fo6a@zte.com.cn Fixes: f65c64f311ee ("delayacct: add delay min to record delay peak") Signed-off-by: Wang Yaxin <wang.yaxin@zte.com.cn> Signed-off-by: xu xin <xu.xin16@zte.com.cn> Signed-off-by: Kun Jiang <jiang.kun2@zte.com.cn> Reviewed-by: Yang Yang <yang.yang29@zte.com.cn> Cc: Balbir Singh <bsingharora@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When module load fails after memory for codetag section is ready, codetag
section memory will not be properly released. This causes memory leak,
and if next module load happens to get the same module address, codetag
may pick the uninitialized section when manipulating tags during module
unload, and leads to "unable to handle page fault" BUG.
Link: https://lkml.kernel.org/r/20250519163823.7540-1-00107082@163.com Fixes: 0db6f8d7820a ("alloc_tag: load module tags into separate contiguous memory") Closes: https://lore.kernel.org/all/20250516131246.6244-1-00107082@163.com/ Signed-off-by: David Wang <00107082@163.com> Acked-by: Suren Baghdasaryan <surenb@google.com> Cc: Petr Pavlu <petr.pavlu@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__alloc_pages_slowpath has no change detection for ac->nodemask in the
part of retry path, while cpuset can modify it in parallel. For some
processes that set mempolicy as MPOL_BIND, this results ac->nodemask
changes, and then the should_reclaim_retry will judge based on the latest
nodemask and jump to retry, while the get_page_from_freelist only
traverses the zonelist from ac->preferred_zoneref, which selected by a
expired nodemask and may cause infinite retries in some cases
cpu 64:
__alloc_pages_slowpath {
/* ..... */
retry:
/* ac->nodemask = 0x1, ac->preferred->zone->nid = 1 */
if (alloc_flags & ALLOC_KSWAPD)
wake_all_kswapds(order, gfp_mask, ac);
/* cpu 1:
cpuset_write_resmask
update_nodemask
update_nodemasks_hier
update_tasks_nodemask
mpol_rebind_task
mpol_rebind_policy
mpol_rebind_nodemask
// mempolicy->nodes has been modified,
// which ac->nodemask point to
Simultaneously starting multiple cpuset01 from LTP can quickly reproduce
this issue on a multi node server when the maximum memory pressure is
reached and the swap is enabled
Link: https://lkml.kernel.org/r/20250416082405.20988-1-zhangtianyang@loongson.cn Fixes: c33d6c06f60f ("mm, page_alloc: avoid looking up the first zone in a zonelist twice") Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn> Reviewed-by: Suren Baghdasaryan <surenb@google.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.com> Cc: Brendan Jackman <jackmanb@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential race between __update_and_free_hugetlb_folio() and
replace_free_hugepage_folios():
CPU1 CPU2
__update_and_free_hugetlb_folio replace_free_hugepage_folios
folio_test_hugetlb(folio)
-- It's still hugetlb folio.
__folio_clear_hugetlb(folio)
hugetlb_free_folio(folio)
h = folio_hstate(folio)
-- Here, h is NULL pointer
When the above race condition occurs, folio_hstate(folio) returns NULL,
and subsequent access to this NULL pointer will cause the system to crash.
To resolve this issue, execute folio_hstate(folio) under the protection
of the hugetlb_lock lock, ensuring that folio_hstate(folio) does not
return NULL.
Link: https://lkml.kernel.org/r/1747884137-26685-1-git-send-email-yangge1116@126.com Fixes: 04f13d241b8b ("mm: replace free hugepage folios after migration") Signed-off-by: Ge Yang <yangge1116@126.com> Reviewed-by: Muchun Song <muchun.song@linux.dev> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Barry Song <21cnbao@gmail.com> Cc: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am seeing soft lockup on certain machine types when a cgroup OOMs. This
is happening because killing the process in certain machine might be very
slow, which causes the soft lockup and RCU stalls. This happens usually
when the cgroup has MANY processes and memory.oom.group is set.
Example I am seeing in real production:
[462012.244552] Memory cgroup out of memory: Killed process 3370438 (crosvm) ....
....
[462037.318059] Memory cgroup out of memory: Killed process 4171372 (adb) ....
[462037.348314] watchdog: BUG: soft lockup - CPU#64 stuck for 26s! [stat_manager-ag:1618982]
....
Quick look at why this is so slow, it seems to be related to serial flush
for certain machine types. For all the crashes I saw, the target CPU was
at console_flush_all().
In the case above, there are thousands of processes in the cgroup, and it
is soft locking up before it reaches the 1024 limit in the code (which
would call the cond_resched()). So, cond_resched() in 1024 blocks is not
sufficient.
Remove the counter-based conditional rescheduling logic and call
cond_resched() unconditionally after each task iteration, after fn() is
called. This avoids the lockup independently of how slow fn() is.
Link: https://lkml.kernel.org/r/20250523-memcg_fix-v1-1-ad3eafb60477@debian.org Fixes: ade81479c7dd ("memcg: fix soft lockup in the OOM process") Signed-off-by: Breno Leitao <leitao@debian.org> Suggested-by: Rik van Riel <riel@surriel.com> Acked-by: Shakeel Butt <shakeel.butt@linux.dev> Cc: Michael van der Westhuizen <rmikey@meta.com> Cc: Usama Arif <usamaarif642@gmail.com> Cc: Pavel Begunkov <asml.silence@gmail.com> Cc: Chen Ridong <chenridong@huawei.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
apply_to_pte_range() enters the lazy MMU mode and then invokes
kasan_populate_vmalloc_pte() callback on each page table walk iteration.
However, the callback can go into sleep when trying to allocate a single
page, e.g. if an architecutre disables preemption on lazy MMU mode enter.
On s390 if make arch_enter_lazy_mmu_mode() -> preempt_enable() and
arch_leave_lazy_mmu_mode() -> preempt_disable(), such crash occurs:
Instead of allocating single pages per-PTE, bulk-allocate the shadow
memory prior to applying kasan_populate_vmalloc_pte() callback on a page
range.
Link: https://lkml.kernel.org/r/c61d3560297c93ed044f0b1af085610353a06a58.1747316918.git.agordeev@linux.ibm.com Fixes: 3c5c3cfb9ef4 ("kasan: support backing vmalloc space with real shadow memory") Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Suggested-by: Andrey Ryabinin <ryabinin.a.a@gmail.com> Reviewed-by: Harry Yoo <harry.yoo@oracle.com> Cc: Daniel Axtens <dja@axtens.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c749d9b7ebbc ("iov_iter: fix copy_page_from_iter_atomic() if
KMAP_LOCAL_FORCE_MAP"), Hugh correctly noted that if KMAP_LOCAL_FORCE_MAP
is enabled, we must limit ourselves to PAGE_SIZE bytes per call to
kmap_local(). The same problem exists in memcpy_from_folio(),
memcpy_to_folio(), folio_zero_tail(), folio_fill_tail() and
memcpy_from_file_folio(), so add folio_test_partial_kmap() to do this more
succinctly.
Link: https://lkml.kernel.org/r/20250514170607.3000994-2-willy@infradead.org Fixes: 00cdf76012ab ("mm: add memcpy_from_file_folio()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a module gets unloaded it checks whether any of its tags are still in
use and if so, we keep the memory containing module's allocation tags
alive until all tags are unused. However percpu counters referenced by
the tags are freed by free_module(). This will lead to UAF if the memory
allocated by a module is accessed after module was unloaded.
To fix this we allocate percpu counters for module allocation tags
dynamically and we keep it alive for tags which are still in use after
module unloading. This also removes the requirement of a larger
PERCPU_MODULE_RESERVE when memory allocation profiling is enabled because
percpu memory for counters does not need to be reserved anymore.
Link: https://lkml.kernel.org/r/20250517000739.5930-1-surenb@google.com Fixes: 0db6f8d7820a ("alloc_tag: load module tags into separate contiguous memory") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Reported-by: David Wang <00107082@163.com> Closes: https://lore.kernel.org/all/20250516131246.6244-1-00107082@163.com/ Tested-by: David Wang <00107082@163.com> Cc: Christoph Lameter (Ampere) <cl@gentwo.org> Cc: Dennis Zhou <dennis@kernel.org> Cc: Kent Overstreet <kent.overstreet@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68bfdc8dc0a1a ("drm/amd: Keep display off while going into S4")
attempted to keep displays off during the S4 sequence by not resuming
display IP. This however leads to hangs because DRM clients such as the
console can try to access registers and cause a hang.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4155 Fixes: 68bfdc8dc0a1a ("drm/amd: Keep display off while going into S4") Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Link: https://lore.kernel.org/r/20250522141328.115095-1-mario.limonciello@amd.com Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e485502c37b097b0bd773baa7e2741bf7bd2909a) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple pointers in struct cifs_search_info (ntwrk_buf_start,
srch_entries_start, and last_entry) point to the same allocated buffer.
However, when freeing this buffer, only ntwrk_buf_start was set to NULL,
while the other pointers remained pointing to freed memory.
This is defensive programming to prevent potential issues with stale
pointers. While the active UAF vulnerability is fixed by the previous
patch, this change ensures consistent pointer state and more robust error
handling.
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com> Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two alarm LEDs of on the uDPU board are stopped working since
commit 78efa53e715e ("leds: Init leds class earlier").
The LEDs are driven by the GPIO{15,16} pins of the North Bridge
GPIO controller. These pins are part of the 'spi_quad' pin group
for which the 'spi' function is selected via the default pinctrl
state of the 'spi' node. This is wrong however, since in order to
allow controlling the LEDs, the pins should use the 'gpio' function.
Before the commit mentined above, the 'spi' function is selected
first by the pinctrl core before probing the spi driver, but then
it gets overridden to 'gpio' implicitly via the
devm_gpiod_get_index_optional() call from the 'leds-gpio' driver.
After the commit, the LED subsystem gets initialized before the
SPI subsystem, so the function of the pin group remains 'spi'
which in turn prevents controlling of the LEDs.
Despite the change of the initialization order, the root cause is
that the pinctrl state definition is wrong since its initial commit 0d45062cfc89 ("arm64: dts: marvell: Add device tree for uDPU board"),
To fix the problem, override the function in the 'spi_quad_pins'
node to 'gpio' and move the pinctrl state definition from the
'spi' node into the 'leds' node.
Cc: stable@vger.kernel.org # needs adjustment for < 6.1 Fixes: 0d45062cfc89 ("arm64: dts: marvell: Add device tree for uDPU board") Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition in the readdir concurrency process, which may
access the rsp buffer after it has been released, triggering the
following KASAN warning.
==================================================================
BUG: KASAN: slab-use-after-free in cifs_fill_dirent+0xb03/0xb60 [cifs]
Read of size 4 at addr ffff8880099b819c by task a.out/342975
The buggy address belongs to the object at ffff8880099b8000
which belongs to the cache cifs_request of size 16588
The buggy address is located 412 bytes inside of
freed 16588-byte region [ffff8880099b8000, ffff8880099bc0cc)
When DP connected to a device with HDR capability,
the hdr structure was filled.Then connected to another
sink device without hdr capability, but the hdr info
still exist.
Fixes: e85959d6cbe0 ("drm: Parse HDR metadata info from EDID") Cc: <stable@vger.kernel.org> # v5.3+ Signed-off-by: "feijuan.li" <feijuan.li@samsung.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://lore.kernel.org/r/20250514063511.4151780-1-feijuan.li@samsung.com Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tj_max value obtained from the Intel TCC library are in Celsius,
whereas the thermal subsystem operates in milli-Celsius.
This discrepancy leads to incorrect trip temperature calculations.
Fix bogus trip temperature by converting tj_max to milli-Celsius Unit.
Fixes: 8ef0ca4a177d ("Merge back other thermal control material for 6.3.") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Reported-by: zhang ning <zhangn1985@outlook.com> Closes: https://lore.kernel.org/all/TY2PR01MB3786EF0FE24353026293F5ACCD97A@TY2PR01MB3786.jpnprd01.prod.outlook.com/ Tested-by: zhang ning <zhangn1985@outlook.com> Cc: 6.3+ <stable@vger.kernel.org> # 6.3+ Link: https://patch.msgid.link/20250519070901.1031233-1-rui.zhang@intel.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the 'buf' array received from the user contains an empty string, the
'length' variable will be zero. Accessing the 'buf' array element with
index 'length - 1' will result in a buffer overflow.
Add a check for an empty string.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: stable@vger.kernel.org Signed-off-by: Vladimir Moskovkin <Vladimir.Moskovkin@kaspersky.com> Link: https://lore.kernel.org/r/39973642a4f24295b4a8fad9109c5b08@kaspersky.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error checking for of_count_phandle_with_args() does not handle
negative error codes correctly. The problem is that "index" is a u32 so
in the condition "if (index >= num_domains)" negative error codes stored
in "num_domains" are type promoted to very high positive values and
"index" is always going to be valid.
Test for negative error codes first and then test if "index" is valid.
Fixes: 3ccf3f0cd197 ("PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/aBxPQ8AI8N5v-7rL@stanley.mountain Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new struct for platform data for the ti,am62-sdhci compatible to
apply additional quirks, namely "SDHCI_QUIRK2_SUPPRESS_V1P8_ENA", to
host controllers with am62 compatible.
Note, the fix was originally introduced by commit 941a7abd4666
("mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch") but was
found to be applied too broadly and had to be reverted.
This fixes MMC init failures seen across am62x boards.
Currently, when device mtu is updated, vmxnet3 updates netdev mtu, quiesces
the device and then reactivates it for the ESXi to know about the new mtu.
So, technically the OS stack can start using the new mtu before ESXi knows
about the new mtu.
This can lead to issues for TSO packets which use mss as per the new mtu
configured. This patch fixes this issue by moving the mtu write after
device quiesce.
Cc: stable@vger.kernel.org Fixes: d1a890fa37f2 ("net: VMware virtual Ethernet NIC driver: vmxnet3") Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com> Acked-by: Guolin Yang <guolin.yang@broadcom.com>
Changes v1-> v2:
Moved MTU write after destroy of rx rings Link: https://patch.msgid.link/20250515190457.8597-1-ronak.doshi@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer arithmentic for accessing the tail tag only works
for linear skbs.
For nonlinear skbs, it reads uninitialized memory inside the
skb headroom, essentially randomizing the tag. I have observed
it gets set to 6 most of the time.
Example where ksz9477_rcv thinks that the packet from port 1 comes from port 6
(which does not exist for the ksz9896 that's in use), dropping the packet.
Debug prints added by me (not included in this patch):
Call skb_linearize before trying to access the tag.
This patch fixes ksz9477_rcv which is used by the ksz9896 I have at
hand, and also applies the same fix to ksz8795_rcv which seems to have
the same problem.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de> CC: stable@vger.kernel.org Fixes: 016e43a26bab ("net: dsa: ksz: Add KSZ8795 tag code") Fixes: 8b8010fb7876 ("dsa: add support for Microchip KSZ tail tagging") Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20250515072920.2313014-1-jakob.unterwurzacher@cherry.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
