During swap activation we iterate over the extents of a file and we can
have many thousands of them, so we can end up in a busy loop monopolizing
a core. Avoid this by doing a voluntary reschedule after processing each
extent.
CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix set charge current limits for devices which allow to set the lowest
charge current limit to be greater zero. If requested charge current limit
is below lowest limit, the index equals current_limit_map_size which leads
to accessing memory beyond allocated memory.
This happens because for an i2c_msg with a len of 0 the driver will
mark the transmission of the message as a success once the START has
been sent, without waiting for the devices on the bus to respond with an
ACK/NAK. Since i2cdetect seems to run in a tight loop over all addresses
the NAK is treated as part of the next test for the next address.
Delete the fast path that marks a message as complete when idev->msg_len
is zero after sending a START/RESTART since this isn't a valid scenario.
Compatible string "fsl,imx7d-i2c" is not exited at i2c-imx driver
compatible string table, at the result, "fsl,imx21-i2c" will be
matched, but it will cause erratum ERR007805 not be applied in fact.
So Add "fsl,imx7d-i2c" compatible string in i2c-imx driver to apply
the erratum ERR007805(https://www.nxp.com/docs/en/errata/IMX7DS_3N09P.pdf).
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
"fsl,imx7d-i2c" already is documented in binding doc. This erratum
fix has been included in imx6_i2c_hwdata and it is the same in all
I.MX6/7/8, so just reuse it.
Fixes: 39c025721d70 ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit") Cc: stable@vger.kernel.org # v5.18+ Signed-off-by: Carlos Song <carlos.song@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Fixes: 39c025721d70 ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit") Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20241218044238.143414-1-carlos.song@nxp.com Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present, where repeated sends are intended to be used, the
i2c-microchip-core driver sends a stop followed by a start. Lots of i2c
devices must not malfunction in the face of this behaviour, because the
driver has operated like this for years! Try to keep track of whether or
not a repeated send is required, and suppress sending a stop in these
cases.
Kun Hu reports that the SQPOLL creating error path has UAF, which
happens if io_uring_alloc_task_context() fails and then io_sq_thread()
manages to run and complete before the rest of error handling code,
which means io_sq_thread_finish() is looking at already killed task.
Note that this is mostly theoretical, requiring fault injection on
the allocation side to trigger in practice.
the frozen task stat was reported as 'D' in cgroup v1.
However, after rewriting the core freezer logic, the frozen task stat is
reported as 'R'. This is confusing, especially when a task with stat of
'S' is frozen.
This bug can be reproduced with these steps:
$ cd /sys/fs/cgroup/freezer/
$ mkdir test
$ sleep 1000 &
[1] 739 // task whose stat is 'S'
$ echo 739 > test/cgroup.procs
$ echo FROZEN > test/freezer.state
$ ps -aux | grep 739
root 739 0.1 0.0 8376 1812 pts/0 R 10:56 0:00 sleep 1000
As shown above, a task whose stat is 'S' was changed to 'R' when it was
frozen.
To solve this regression, simply maintain the same reported state as
before the rewrite.
task_state_index() ignores uninteresting state flags (such as
TASK_FREEZABLE) for most states, but for TASK_IDLE and TASK_RTLOCK_WAIT
it does not.
So if a task is waiting TASK_IDLE|TASK_FREEZABLE it gets incorrectly
reported as TASK_UNINTERRUPTIBLE or "D". (it is planned for nfsd to
change to use this state).
Fix this by only testing the interesting bits and not the irrelevant
bits in __task_state_index()
These HP laptops use Realtek HDA codec ALC3315 combined CS35L56
Amplifiers. They need the quirk ALC285_FIXUP_HP_GPIO_LED to get
the micmute LED working.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com> Reviewed-by: Simon Trimmer <simont@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Link: https://patch.msgid.link/20241202144659.1553504-1-chris.chiu@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a newly-added link type doesn't invoke BPF_LINK_TYPE(), accessing
bpf_link_type_strs[link->type] may result in an out-of-bounds access.
To spot such missed invocations early in the future, checking the
validity of link->type in bpf_link_show_fdinfo() and emitting a warning
when such invocations are missed.
Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20241024013558.1135167-3-houtao@huaweicloud.com
[ shung-hsi.yu: break up existing seq_printf() call since commit 68b04864ca42
("bpf: Create links for BPF struct_ops maps.") is not present ] Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When profile rollback fails in mlx5e_netdev_change_profile, the netdev
profile var is left set to NULL. Avoid a crash when unloading the driver
by not calling profile->cleanup in such a case.
This was encountered while testing, with the original trigger that
the wq rescuer thread creation got interrupted (presumably due to
Ctrl+C-ing modprobe), which gets converted to ENOMEM (-12) by
mlx5e_priv_init, the profile rollback also fails for the same reason
(signal still active) so the profile is left as NULL, leading to a crash
later in _mlx5e_remove.
If the caller of vmap() specifies VM_MAP_PUT_PAGES (currently only the
i915 driver), we will decrement nr_vmalloc_pages and MEMCG_VMALLOC in
vfree(). These counters are incremented by vmalloc() but not by vmap() so
this will cause an underflow. Check the VM_MAP_PUT_PAGES flag before
decrementing either counter.
Link: https://lkml.kernel.org/r/20241211202538.168311-1-willy@infradead.org Fixes: b944afc9d64d ("mm: add a VM_MAP_PUT_PAGES flag for vmap") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev> Reviewed-by: Balbir Singh <balbirs@nvidia.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Muchun Song <muchun.song@linux.dev> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: "Uladzislau Rezki (Sony)" <urezki@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 4ce6e2db00de ("virtio-blk: Ensure no requests in virtqueues before
deleting vqs.") replaces queue quiesce with queue freeze in virtio-blk's
PM callbacks. And the motivation is to drain inflight IOs before suspending.
block layer's queue freeze looks very handy, but it is also easy to cause
deadlock, such as, any attempt to call into bio_queue_enter() may run into
deadlock if the queue is frozen in current context. There are all kinds
of ->suspend() called in suspend context, so keeping queue frozen in the
whole suspend context isn't one good idea. And Marek reported lockdep
warning[1] caused by virtio-blk's freeze queue in virtblk_freeze().
Given the motivation is to drain in-flight IOs, it can be done by calling
freeze & unfreeze, meantime restore to previous behavior by keeping queue
quiesced during suspend.
Cc: Yi Sun <yi.sun@unisoc.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: virtualization@lists.linux.dev Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Acked-by: Stefan Hajnoczi <stefanha@redhat.com> Link: https://lore.kernel.org/r/20241112125821.1475793-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
While receiving an MST up request message from one thread in
drm_dp_mst_handle_up_req(), the MST topology could be removed from
another thread via drm_dp_mst_topology_mgr_set_mst(false), freeing
mst_primary and setting drm_dp_mst_topology_mgr::mst_primary to NULL.
This could lead to a NULL deref/use-after-free of mst_primary in
drm_dp_mst_handle_up_req().
Avoid the above by holding a reference for mst_primary in
drm_dp_mst_handle_up_req() while it's used.
v2: Fix kfreeing the request if getting an mst_primary reference fails.
This partially reverts commit 812fe6420a6e ("scsi: storvsc: Handle
additional SRB status values").
HyperV does not support MAINTENANCE_IN resulting in FC passthrough
returning the SRB_STATUS_DATA_OVERRUN value. Now that
SRB_STATUS_DATA_OVERRUN is treated as an error, multipath ALUA paths go
into a faulty state as multipath ALUA submits RTPG commands via
MAINTENANCE_IN.
GCC 15 introduces -Werror=unterminated-string-initialization by default,
this results in the following build error
fs/smb/server/smb_common.c:21:35: error: initializer-string for array of 'char' is too long [-Werror=unterminated-string-ini
tialization]
21 | static const char basechars[43] = "0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ_-!@#$%";
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
To this we are replacing char basechars[43] with a character pointer
and then using strlen to get the length.
Signed-off-by: Brahmajit Das <brahmajit.xyz@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Z60MR100 startup, speaker will output a pop. To fix this issue,
we mute codec by init verbs in bios when system startup, and set GPIO
to low to unmute codec in codec driver when it loaded .
[ white space fixes and compile warning fix by tiwai ]
Fix the hardware revision numbering for Qlogic ISP1020/1040 boards. HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com> Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the watchdog timer to work properly on the QCML04 board we need to
set PWRGD enable in the Environment Controller Configuration Registers
Special Configuration Register 1 when it is not already set, this may
be the case when the watchdog is not enabled from within the BIOS.
Make sure the trace_kprobe's module notifer callback function is called
after jump_label's callback is called. Since the trace_kprobe's callback
eventually checks jump_label address during registering new kprobe on
the loading module, jump_label must be updated before this registration
happens.
For the most part of the C++ history, it couldn't have type
declarations inside anonymous unions for different reasons. At the
same time, __struct_group() relies on the latters, so when the @TAG
argument is not empty, C++ code doesn't want to build (even under
`extern "C"`):
../linux/include/uapi/linux/pkt_cls.h:25:24: error:
'struct tc_u32_sel::<unnamed union>::tc_u32_sel_hdr,' invalid;
an anonymous union may only have public non-static data members
[-fpermissive]
The safest way to fix this without trying to switch standards (which
is impossible in UAPI anyway) etc., is to disable tag declaration
for that language. This won't break anything since for now it's not
buildable at all.
Use a separate definition for __struct_group() when __cplusplus is
defined to mitigate the error, including the version from tools/.
Fixes: 50d7bd38c3aa ("stddef: Introduce struct_group() helper macro") Reported-by: Christopher Ferris <cferris@google.com> Closes: https://lore.kernel.org/linux-hardening/Z1HZpe3WE5As8UAz@google.com Suggested-by: Kees Cook <kees@kernel.org> # __struct_group_tag() Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20241219135734.2130002-1-aleksander.lobakin@intel.com Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mapping VMA address is saved in VAS window struct when the
paste address is mapped. This VMA address is used during migration
to unmap the paste address if the window is active. The paste
address mapping will be removed when the window is closed or with
the munmap(). But the VMA address in the VAS window is not updated
with munmap() which is causing invalid access during migration.
The KASAN report shows:
[16386.254991] BUG: KASAN: slab-use-after-free in reconfig_close_windows+0x1a0/0x4e8
[16386.255043] Read of size 8 at addr c00000014a819670 by task drmgr/696928
[16386.256136] Allocated by task 696554 on cpu 31 at 16377.277618s:
[16386.256149] kasan_save_stack+0x34/0x68
[16386.256163] kasan_save_track+0x34/0x80
[16386.256175] kasan_save_alloc_info+0x58/0x74
[16386.256196] __kasan_slab_alloc+0xb8/0xdc
[16386.256209] kmem_cache_alloc_noprof+0x200/0x3d0
[16386.256225] vm_area_alloc+0x44/0x150
[16386.256245] mmap_region+0x214/0x10c4
[16386.256265] do_mmap+0x5fc/0x750
[16386.256277] vm_mmap_pgoff+0x14c/0x24c
[16386.256292] ksys_mmap_pgoff+0x20c/0x348
[16386.256303] sys_mmap+0xd0/0x160
...
[16386.256350] Freed by task 0 on cpu 31 at 16386.204848s:
[16386.256363] kasan_save_stack+0x34/0x68
[16386.256374] kasan_save_track+0x34/0x80
[16386.256384] kasan_save_free_info+0x64/0x10c
[16386.256396] __kasan_slab_free+0x120/0x204
[16386.256415] kmem_cache_free+0x128/0x450
[16386.256428] vm_area_free_rcu_cb+0xa8/0xd8
[16386.256441] rcu_do_batch+0x2c8/0xcf0
[16386.256458] rcu_core+0x378/0x3c4
[16386.256473] handle_softirqs+0x20c/0x60c
[16386.256495] do_softirq_own_stack+0x6c/0x88
[16386.256509] do_softirq_own_stack+0x58/0x88
[16386.256521] __irq_exit_rcu+0x1a4/0x20c
[16386.256533] irq_exit+0x20/0x38
[16386.256544] interrupt_async_exit_prepare.constprop.0+0x18/0x2c
...
[16386.256717] Last potentially related work creation:
[16386.256729] kasan_save_stack+0x34/0x68
[16386.256741] __kasan_record_aux_stack+0xcc/0x12c
[16386.256753] __call_rcu_common.constprop.0+0x94/0xd04
[16386.256766] vm_area_free+0x28/0x3c
[16386.256778] remove_vma+0xf4/0x114
[16386.256797] do_vmi_align_munmap.constprop.0+0x684/0x870
[16386.256811] __vm_munmap+0xe0/0x1f8
[16386.256821] sys_munmap+0x54/0x6c
[16386.256830] system_call_exception+0x1a0/0x4a0
[16386.256841] system_call_vectored_common+0x15c/0x2ec
[16386.256868] The buggy address belongs to the object at c00000014a819670
which belongs to the cache vm_area_struct of size 168
[16386.256887] The buggy address is located 0 bytes inside of
freed 168-byte region [c00000014a819670, c00000014a819718)
This patch adds close() callback in vas_vm_ops vm_operations_struct
which will be executed during munmap() before freeing VMA. The VMA
address in the VAS window is set to NULL after holding the window
mmap_mutex.
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
The at_xdmac_memset_create_desc may return NULL, which will lead to a
null pointer dereference. For example, the len input is error, or the
atchan->free_descs_list is empty and memory is exhausted. Therefore, add
check to avoid this.
The ADMAC attached to the AOP has complex power sequencing, and is
power gated when the probe callback runs. Move the register reads
to other functions, where we can guarantee that the hardware is
switched on.
Currently, the driver does not return the correct DMA status when a DMA
pause is issued by the client drivers. This causes GPCDMA users to
assume that DMA is still running, while in reality, the DMA is paused.
Return DMA_PAUSED for tx_status() if the channel is paused in the middle
of a transfer.
The recently submitted fix-commit revealed a problem in the iDMA 32-bit
platform code. Even though the controller supported only a single master
the dw_dma_acpi_filter() method hard-coded two master interfaces with IDs
0 and 1. As a result the sanity check implemented in the commit b336268dde75 ("dmaengine: dw: Add peripheral bus width verification")
got incorrect interface data width and thus prevented the client drivers
from configuring the DMA-channel with the EINVAL error returned. E.g.,
the next error was printed for the PXA2xx SPI controller driver trying
to configure the requested channels:
> [ 164.525604] pxa2xx_spi_pci 0000:00:07.1: DMA slave config failed
> [ 164.536105] pxa2xx_spi_pci 0000:00:07.1: failed to get DMA TX descriptor
> [ 164.543213] spidev spi-SPT0001:00: SPI transfer failed: -16
The problem would have been spotted much earlier if the iDMA 32-bit
controller supported more than one master interfaces. But since it
supports just a single master and the iDMA 32-bit specific code just
ignores the master IDs in the CTLLO preparation method, the issue has
been gone unnoticed so far.
Fix the problem by specifying the default master ID for both memory
and peripheral devices in the driver data. Thus the issue noticed for
the iDMA 32-bit controllers will be eliminated and the ACPI-probed
DW DMA controllers will be configured with the correct master ID by
default.
Currently, the USB port via combophy on the RK3528/RK3588 SoC is broken.
usb usb8-port1: Cannot enable. Maybe the USB cable is bad?
This is due to the combphy of RK3528/RK3588 SoC has multiple resets, but
only "phy resets" need assert and deassert, "apb resets" don't need.
So change the driver to only match the phy resets, which is also what
the vendor kernel does.
When bringing up the PHY, it might be in a bad state if left powered.
One case is we lose the PLL lock if the PLL is gated while the PHY
is powered. Toggle the PHY power so we can start from a known state.
Fixes: 4e5b9c9a73b3 ("phy: usb: Add support for new Synopsys USB controller on the 7216") Signed-off-by: Justin Chen <justin.chen@broadcom.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20241024213540.1059412-1-justin.chen@broadcom.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devm_phy_destroy(), its comment says it needs to invoke phy_destroy()
to destroy the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_consume(), and the missing
phy_destroy() call will cause that the phy fails to be destroyed.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
For devm_of_phy_provider_unregister(), its comment says it needs to invoke
of_phy_provider_unregister() to unregister the phy provider, but it will
not actually invoke the function since devres_destroy() does not call
devm_phy_provider_release(), and the missing of_phy_provider_unregister()
call will cause:
- The phy provider fails to be unregistered.
- Leak both memory and the OF node refcount.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
For devm_phy_put(), its comment says it needs to invoke phy_put() to
release the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_release(), and the missing
phy_put() call will cause:
- The phy fails to be released.
- devm_phy_put() can not fully undo what API devm_phy_get() does.
- Leak refcount of both the module and device for below typical usage:
devm_phy_get(); // or its variant
...
err = do_something();
if (err)
goto err_out;
...
err_out:
devm_phy_put(); // leak refcount here
The file(s) affected by this issue are shown below since they have such
typical usage.
drivers/pci/controller/cadence/pcie-cadence.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework") Cc: stable@vger.kernel.org Cc: Lorenzo Pieralisi <lpieralisi@kernel.org> Cc: Krzysztof Wilczyński <kw@linux.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-1-40ae28f5015a@quicinc.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For macro for_each_child_of_node(parent, child), refcount of @child has
been increased before entering its loop body, so normally needs to call
of_node_put(@child) before returning from the loop body to avoid refcount
leakage.
of_phy_provider_lookup() has such usage but does not call of_node_put()
before returning, so cause leakage of the OF node refcount.
Fix by simply calling of_node_put() before returning from the loop body.
The APIs affected by this issue are shown below since they indirectly
invoke problematic of_phy_provider_lookup().
phy_get()
of_phy_get()
devm_phy_get()
devm_of_phy_get()
devm_of_phy_get_by_index()
Fixes: 2a4c37016ca9 ("phy: core: Fix of_phy_provider_lookup to return PHY provider for sub node") Cc: stable@vger.kernel.org Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-5-40ae28f5015a@quicinc.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_of_phy_get() will directly return when suffers of_device_is_compatible()
error, but it forgets to decrease refcount of OF node @args.np before error
return, the refcount was increased by previous of_parse_phandle_with_args()
so causes the OF node's refcount leakage.
Fix by decreasing the refcount via of_node_put() before the error return.
Fixes: b7563e2796f8 ("phy: work around 'phys' references to usb-nop-xceiv devices") Cc: stable@vger.kernel.org Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-4-40ae28f5015a@quicinc.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RX Lane configuration sequence of SC8280XP, the register
V5_RX_UCDR_FO_GAIN is incorrectly spelled as RX_UCDR_SO_GAIN and
hence the programming sequence is wrong. Fix the register sequence
accordingly to avoid any compliance failures. This has been tested
on SA8775P by checking device mode enumeration in SuperSpeed.
The NAND chip-selects are registered for the Arasan driver during
initialization but are not de-registered when the driver is unloaded. As a
result, if the driver is loaded again, the chip-selects remain registered
and busy, making them unavailable for use.
When two chip-selects are configured in the device tree, and the second is
a non-native GPIO, both the GPIO-based chip-select and the first native
chip-select may be asserted simultaneously. This double assertion causes
incorrect read and write operations.
The issue occurs because when nfc->ncs <= 2, nfc->spare_cs is always
initialized to 0 due to static initialization. Consequently, when the
second chip-select (GPIO-based) is selected in anfc_assert_cs(), it is
detected by anfc_is_gpio_cs(), and nfc->native_cs is assigned the value 0.
This results in both the GPIO-based chip-select being asserted and the
NAND controller register receiving 0, erroneously selecting the native
chip-select.
This patch resolves the issue, as confirmed by oscilloscope testing with
configurations involving two or more chip-selects in the device tree.
There may be a potential integer overflow issue in inftl_partscan().
parts[0].size is defined as "uint64_t" while mtd->erasesize and
ip->firstUnit are defined as 32-bit unsigned integer. The result of
the calculation will be limited to 32 bits without correct casting.
skb_network_offset() and skb_transport_offset() can be negative when
they are called after we pull the transport header, for example, when
we use eBPF sockmap at the point of ->sk_data_ready().
__bpf_skb_min_len() uses an unsigned int to get these offsets, this
leads to a very large number which then causes bpf_skb_change_tail()
failed unexpectedly.
Fix this by using a signed int to get these offsets and ensure the
minimum is at least zero.
Fixes: 5293efe62df8 ("bpf: add bpf_skb_change_tail helper") Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20241213034057.246437-2-xiyou.wangcong@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When we do sk_psock_verdict_apply->sk_psock_skb_ingress, an sk_msg will
be created out of the skb, and the rmem accounting of the sk_msg will be
handled by the skb.
For skmsgs in __SK_REDIRECT case of tcp_bpf_send_verdict, when redirecting
to the ingress of a socket, although we sk_rmem_schedule and add sk_msg to
the ingress_msg of sk_redir, we do not update sk_rmem_alloc. As a result,
except for the global memory limit, the rmem of sk_redir is nearly
unlimited. Thus, add sk_rmem_alloc related logic to limit the recv buffer.
Since the function sk_msg_recvmsg and __sk_psock_purge_ingress_msg are
used in these two paths. We use "msg->skb" to test whether the sk_msg is
skb backed up. If it's not, we shall do the memory accounting explicitly.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20241210012039.1669389-3-zijianzhang@bytedance.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When bpf_tcp_ingress() is called, the skmsg is being redirected to the
ingress of the destination socket. Therefore, we should charge its
receive socket buffer, instead of sending socket buffer.
Because sk_rmem_schedule() tests pfmemalloc of skb, we need to
introduce a wrapper and call it for skmsg.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20241210012039.1669389-2-zijianzhang@bytedance.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: d3116756a710 ("drm/ttm: rename bo->mem and make it a pointer") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3837 Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Michel Dänzer <mdaenzer@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 695c2c745e5dff201b75da8a1d237ce403600d04) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kiocb_done() should care to specifically redirecting requests to io-wq.
Remove the hopping to tw to then queue an io-wq, return -EAGAIN and let
the core code io_uring handle offloading.
Some file systems, ocfs2 in this case, will return -EOPNOTSUPP for
an IOCB_NOWAIT read/write attempt. While this can be argued to be
correct, the usual return value for something that requires blocking
issue is -EAGAIN.
A refactoring io_uring commit dropped calling kiocb_done() for
negative return values, which is otherwise where we already do that
transformation. To ensure we catch it in both spots, check it in
__io_read() itself as well.
Reported-by: Robert Sander <r.sander@heinlein-support.de> Link: https://fosstodon.org/@gurubert@mastodon.gurubert.de/113112431889638440 Cc: stable@vger.kernel.org Fixes: a08d195b586a ("io_uring/rw: split io_read() into a helper") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, the epoll only use wake_up() interface to wake up task.
However, sometimes, there are epoll users which want to use
the synchronous wakeup flag to hint the scheduler, such as
Android binder driver.
So add a wake_up_sync() define, and use the wake_up_sync()
when the sync is true in ep_poll_callback().
Co-developed-by: Jing Xia <jing.xia@unisoc.com> Signed-off-by: Jing Xia <jing.xia@unisoc.com> Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com> Link: https://lore.kernel.org/r/20240426080548.8203-1-xuewen.yan@unisoc.com Tested-by: Brian Geffon <bgeffon@google.com> Reviewed-by: Brian Geffon <bgeffon@google.com> Reported-by: Benoit Lize <lizeb@google.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Cc: Brian Geffon <bgeffon@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When directory's last extent has more that one block and its length is
not multiple of a block side, the code wrongly decided to move to the
next extent instead of processing the last partial block. This led to
directory corruption. Fix the rounding issue.
Signed-off-by: Jan Kara <jack@suse.cz> Cc: Shreenidhi Shedi <yesshedi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It becomes a path component, so it shouldn't exceed NAME_MAX
characters. This was hardened in commit c152737be22b ("ceph: Use
strscpy() instead of strcpy() in __get_snap_name()"), but no actual
check was put in place.
__of_get_dma_parent() returns OF device node @args.np, but the node's
refcount is increased twice, by both of_parse_phandle_with_args() and
of_node_get(), so causes refcount leakage for the node.
Fix by directly returning the node got by of_parse_phandle_with_args().
Fixes: f83a6e5dea6c ("of: address: Add support for the parent DMA bus") Cc: stable@vger.kernel.org Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20241206-of_core_fix-v1-4-dc28ed56bec3@quicinc.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code uses some 'goto put;' to cancel the parsing operation
and can lead to a return code value of 0 even on error cases.
Indeed, some goto calls are done from a loop without setting the ret
value explicitly before the goto call and so the ret value can be set to
0 due to operation done in previous loop iteration. For instance match
can be set to 0 in the previous loop iteration (leading to a new
iteration) but ret can also be set to 0 it the of_property_read_u32()
call succeed. In that case if no match are found or if an error is
detected the new iteration, the return value can be wrongly 0.
Avoid those cases setting the ret value explicitly before the goto
calls.
Fixes: bd6f2fd5a1d5 ("of: Support parsing phandle argument lists through a nexus node") Cc: stable@vger.kernel.org Signed-off-by: Herve Codina <herve.codina@bootlin.com> Link: https://lore.kernel.org/r/20241202165819.158681-1-herve.codina@bootlin.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When F_SEAL_FUTURE_WRITE was introduced, it was overlooked that udmabuf
must reject memfds with this flag, just like ones with F_SEAL_WRITE.
Fix it by adding F_SEAL_FUTURE_WRITE to SEALS_DENIED.
Fixes: ab3948f58ff8 ("mm/memfd: add an F_SEAL_FUTURE_WRITE seal to memfd") Cc: stable@vger.kernel.org Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20241204-udmabuf-fixes-v2-2-23887289de1c@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the inode bitmap is corrupted, an inode with an inode number that
should exist as a ".nilfs" file was reassigned by nilfs_mkdir for "file0",
causing an inode duplication during execution. And this causes an
underflow of i_nlink in rmdir operations.
The inode is used twice by the same task to unmount and remove directories
".nilfs" and "file0", it trigger warning in nilfs_rmdir.
Avoid to this issue, check i_nlink in nilfs_iget(), if it is 0, it means
that this inode has been deleted, and iput is executed to reclaim it.
When block_invalidatepage was converted to block_invalidate_folio, the
fallback to block_invalidatepage in folio_invalidate() if the
address_space_operations method invalidatepage (currently
invalidate_folio) was not set, was removed.
Unfortunately, some pseudo-inodes in nilfs2 use empty_aops set by
inode_init_always_gfp() as is, or explicitly set it to
address_space_operations. Therefore, with this change,
block_invalidatepage() is no longer called from folio_invalidate(), and as
a result, the buffer_head structures attached to these pages/folios are no
longer freed via try_to_free_buffers().
Thus, these buffer heads are now leaked by truncate_inode_pages(), which
cleans up the page cache from inode evict(), etc.
Three types of caches use empty_aops: gc inode caches and the DAT shadow
inode used by GC, and b-tree node caches. Of these, b-tree node caches
explicitly call invalidate_mapping_pages() during cleanup, which involves
calling try_to_free_buffers(), so the leak was not visible during normal
operation but worsened when GC was performed.
Fix this issue by using address_space_operations with invalidate_folio set
to block_invalidate_folio instead of empty_aops, which will ensure the
same behavior as before.
On a malformed interrupt-map property which is shorter than expected by
1 cell, we may read bogus data past the end of the property instead of
returning an error in of_irq_parse_imap_parent().
Decrement the remaining length when skipping over the interrupt parent
phandle cell.
Fixes: 935df1bd40d4 ("of/irq: Factor out parsing of interrupt-map parent phandle+args from of_irq_parse_raw()") Cc: stable@vger.kernel.org Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20241209-of_irq_fix-v1-1-782f1419c8a1@quicinc.com
[rh: reword commit msg] Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the server is recalling a layout, we should ignore the count of
outstanding layoutget calls, since the server is expected to return
either NFS4ERR_RECALLCONFLICT or NFS4ERR_RETURNCONFLICT for as long as
the recall is outstanding.
Currently, we may end up livelocking, causing the layout to eventually
be forcibly revoked.
Fixes: bf0291dd2267 ("pNFS: Ensure LAYOUTGET and LAYOUTRETURN are properly serialised") Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
task work can be executed after the task has gone through io_uring
termination, whether it's the final task_work run or the fallback path.
In this case, task work will find ->io_wq being already killed and
null'ed, which is a problem if it then tries to forward the request to
io_queue_iowq(). Make io_queue_iowq() fail requests in this case.
Note that it also checks PF_KTHREAD, because the user can first close
a DEFER_TASKRUN ring and shortly after kill the task, in which case
->iowq check would race.
Currently, io_uring_unreg_ringfd() (which cleans up registered rings) is
only called on exit, but __io_uring_free (which frees the tctx in which the
registered ring pointers are stored) is also called on execve (via
begin_new_exec -> io_uring_task_cancel -> __io_uring_cancel ->
io_uring_cancel_generic -> __io_uring_free).
This means: A process going through execve while having registered rings
will leak references to the rings' `struct file`.
Fix it by zapping registered rings on execve(). This is implemented by
moving the io_uring_unreg_ringfd() from io_uring_files_cancel() into its
callee __io_uring_cancel(), which is called from io_uring_task_cancel() on
execve.
This could probably be exploited *on 32-bit kernels* by leaking 2^32
references to the same ring, because the file refcount is stored in a
pointer-sized field and get_file() doesn't have protection against
refcount overflow, just a WARN_ONCE(); but on 64-bit it should have no
impact beyond a memory leak.
Cc: stable@vger.kernel.org Fixes: e7a6c00dc77a ("io_uring: add support for registering ring file descriptors") Signed-off-by: Jann Horn <jannh@google.com> Link: https://lore.kernel.org/r/20241218-uring-reg-ring-cleanup-v1-1-8f63e999045b@google.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, LoongArch LLVM does not support the constraint "o" and no plan
to support it, it only supports the similar constraint "m", so change the
constraints from "nor" in the "else" case to arch-specific "nmr" to avoid
the build error such as "unexpected asm memory constraint" for LoongArch.
The test_event_printk() code makes sure that when a trace event is
registered, any dereferenced pointers in from the event's TP_printk() are
pointing to content in the ring buffer. But currently it does not handle
"%s", as there's cases where the string pointer saved in the ring buffer
points to a static string in the kernel that will never be freed. As that
is a valid case, the pointer needs to be checked at runtime.
Currently the runtime check is done via trace_check_vprintf(), but to not
have to replicate everything in vsnprintf() it does some logic with the
va_list that may not be reliable across architectures. In order to get rid
of that logic, more work in the test_event_printk() needs to be done. Some
of the strings can be validated at this time when it is obvious the string
is valid because the string will be saved in the ring buffer content.
Do all the validation of strings in the ring buffer at boot in
test_event_printk(), and make sure that the field of the strings that
point into the kernel are accessible. This will allow adding checks at
runtime that will validate the fields themselves and not rely on paring
the TP_printk() format at runtime.
Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/20241217024720.685917008@goodmis.org Fixes: 5013f454a352c ("tracing: Add check of trace event print fmts for dereferencing pointers") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The process_pointer() helper function looks to see if various trace event
macros are used. These macros are for storing data in the event. This
makes it safe to dereference as the dereference will then point into the
event on the ring buffer where the content of the data stays with the
event itself.
The test_event_printk() analyzes print formats of trace events looking for
cases where it may dereference a pointer that is not in the ring buffer
which can possibly be a bug when the trace event is read from the ring
buffer and the content of that pointer no longer exists.
The function needs to accurately go from one print format argument to the
next. It handles quotes and parenthesis that may be included in an
argument. When it finds the start of the next argument, it uses a simple
"c = strstr(fmt + i, ',')" to find the end of that argument!
In order to include "%s" dereferencing, it needs to process the entire
content of the print format argument and not just the content of the first
',' it finds. As there may be content like:
Which is an example of a full argument of an existing event. As the code
already handles finding the next print format argument, process the
argument at the end of it and not the start of it. This way it has both
the start of the argument as well as the end of it.
Add a helper function "process_pointer()" that will do the processing during
the loop as well as at the end. It also makes the code cleaner and easier
to read.
Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/20241217024720.362271189@goodmis.org Fixes: 5013f454a352c ("tracing: Add check of trace event print fmts for dereferencing pointers") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use is_64_bit_hypercall() instead of is_64_bit_mode() to detect a 64-bit
hypercall when completing said hypercall. For guests with protected state,
e.g. SEV-ES and SEV-SNP, KVM must assume the hypercall was made in 64-bit
mode as the vCPU state needed to detect 64-bit mode is unavailable.
Hacking the sev_smoke_test selftest to generate a KVM_HC_MAP_GPA_RANGE
hypercall via VMGEXIT trips the WARN:
This can happen because the KVP/VSS channel callback can be invoked
even before the channel is fully opened:
1) as soon as hv_kvp_init() -> hvutil_transport_init() creates
/dev/vmbus/hv_kvp, the kvp daemon can open the device file immediately and
register itself to the driver by writing a message KVP_OP_REGISTER1 to the
file (which is handled by kvp_on_msg() ->kvp_handle_handshake()) and
reading the file for the driver's response, which is handled by
hvt_op_read(), which calls hvt->on_read(), i.e. kvp_register_done().
2) the problem with kvp_register_done() is that it can cause the
channel callback to be called even before the channel is fully opened,
and when the channel callback is starting to run, util_probe()->
vmbus_open() may have not initialized the ringbuffer yet, so the
callback can hit the panic of NULL pointer dereference.
To reproduce the panic consistently, we can add a "ssleep(10)" for KVP in
__vmbus_open(), just before the first hv_ringbuffer_init(), and then we
unload and reload the driver hv_utils, and run the daemon manually within
the 10 seconds.
Fix the panic by reordering the steps in util_probe() so the char dev
entry used by the KVP or VSS daemon is not created until after
vmbus_open() has completed. This reordering prevents the race condition
from happening.
Reported-by: Dexuan Cui <decui@microsoft.com> Fixes: e0fa3e5e7df6 ("Drivers: hv: utils: fix a race on userspace daemons registration") Cc: stable@vger.kernel.org Signed-off-by: Michael Kelley <mhklinux@outlook.com> Acked-by: Wei Liu <wei.liu@kernel.org> Link: https://lore.kernel.org/r/20241106154247.2271-3-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20241106154247.2271-3-mhklinux@outlook.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
There is a bug report in the mailing list where btrfs_run_delayed_refs()
failed to drop the ref count for logical 25870311358464 num_bytes 2113536.
[CAUSE]
There is no concrete evidence yet, but considering 0 -> 1 is also a
single bit flipped, it's possible that hardware memory bitflip is
involved, causing the on-disk extent tree to be corrupted.
[FIX]
To prevent us reading such corrupted extent item, or writing such
damaged extent item back to disk, enhance the handling of
BTRFS_EXTENT_DATA_REF_KEY and BTRFS_SHARED_DATA_REF_KEY keys for both
inlined and key items, to detect such 0 ref count and reject them.
CC: stable@vger.kernel.org # 5.4+ Link: https://lore.kernel.org/linux-btrfs/7c69dd49-c346-4806-86e7-e6f863a66f48@app.fastmail.com/ Reported-by: Frankie Fisher <frankie@terrorise.me.uk> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting backing device is done before ZRAM initialization. If we set the
backing device, then remove the ZRAM module without initializing the
device, the backing device reference will be leaked and the device will be
hold forever.
Fix this by always reset the ZRAM fully on rmmod or reset store.
Patch series "zram: fix backing device setup issue", v2.
This series fixes two bugs of backing device setting:
- ZRAM should reject using a zero sized (or the uninitialized ZRAM
device itself) as the backing device.
- Fix backing device leaking when removing a uninitialized ZRAM
device.
This patch (of 2):
Setting a zero sized block device as backing device is pointless, and one
can easily create a recursive loop by setting the uninitialized ZRAM
device itself as its own backing device by (zram0 is uninitialized):
echo /dev/zram0 > /sys/block/zram0/backing_dev
It's definitely a wrong config, and the module will pin itself, kernel
should refuse doing so in the first place.
By refusing to use zero sized device we avoided misuse cases including
this one above.
On SH, devm_clk_get_optional_enabled() fails with -EINVAL if the clock
is not found. This happens because __devm_clk_get() assumes it can pass
a NULL clock pointer (as returned by clk_get_optional()) to the init()
function (clk_prepare_enable() in this case), while the SH
implementation of clk_enable() considers that an error.
Fix this by making the SH clk_enable() implementation return zero
instead, like the Common Clock Framework does.
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Acked-by: Stephen Boyd <sboyd@kernel.org> Link: https://lore.kernel.org/r/b53e6b557b4240579933b3359dda335ff94ed5af.1675354849.git.geert+renesas@glider.be Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The values returned by the driver after processing the contents of the
Temperature Result and the Temperature Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect.
According to the TMP512 and TMP513 datasheets, the Temperature Result (08h
to 0Bh) and Limit (11h to 14h) Registers are 13-bit two's complement
integer values, shifted left by 3 bits. The value is scaled by 0.0625
degrees Celsius per bit. E.g., if regval = 1 1110 0111 0000 000, the
output should be -25 degrees, but the driver will return +487 degrees.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.") Signed-off-by: Murad Masimov <m.masimov@maxima.ru> Link: https://lore.kernel.org/r/20241216173648.526-4-m.masimov@maxima.ru
[groeck: fixed description line length] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value returned by the driver after processing the contents of the
Current Register does not correspond to the TMP512/TMP513 specifications.
A raw register value is converted to a signed integer value by a sign
extension in accordance with the algorithm provided in the specification,
but due to the off-by-one error in the sign bit index, the result is
incorrect. Moreover, negative values will be reported as large positive
due to missing sign extension from u32 to long.
According to the TMP512 and TMP513 datasheets, the Current Register (07h)
is a 16-bit two's complement integer value. E.g., if regval = 1000 0011
0000 0000, then the value must be (-32000 * lsb), but the driver will
return (33536 * lsb).
Fix off-by-one bug, and also cast data->curr_lsb_ua (which is of type u32)
to long to prevent incorrect cast for negative values.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.") Signed-off-by: Murad Masimov <m.masimov@maxima.ru> Link: https://lore.kernel.org/r/20241216173648.526-3-m.masimov@maxima.ru
[groeck: Fixed description line length] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The values returned by the driver after processing the contents of the
Shunt Voltage Register and the Shunt Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect. Moreover, the PGA shift calculated with
the tmp51x_get_pga_shift function is relevant only to the Shunt Voltage
Register, but is also applied to the Shunt Limit Registers.
According to the TMP512 and TMP513 datasheets, the Shunt Voltage Register
(04h) is 13 to 16 bit two's complement integer value, depending on the PGA
setting. The Shunt Positive (0Ch) and Negative (0Dh) Limit Registers are
16-bit two's complement integer values. Below are some examples:
* Shunt Voltage Register
If PGA = 8, and regval = 1000 0011 0000 0000, then the decimal value must
be -32000, but the value calculated by the driver will be 33536.
* Shunt Limit Register
If regval = 1000 0011 0000 0000, then the decimal value must be -32000, but
the value calculated by the driver will be 768, if PGA = 1.
Fix sign bit index, and also correct misleading comment describing the
tmp51x_get_pga_shift function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Since 2320c9e6a768 ("drm/sched: memset() 'job' in drm_sched_job_init()")
accessing job->base.sched can produce unexpected results as the initialisation
of (*job)->base.sched done in amdgpu_job_alloc is overwritten by the
memset.
This commit fixes an issue when a CS would fail validation and would
be rejected after job->num_ibs is incremented. In this case,
amdgpu_ib_free(ring->adev, ...) will be called, which would crash the
machine because the ring value is bogus.
To fix this, pass a NULL pointer to amdgpu_ib_free(): we can do this
because the device is actually not used in this function.
The next commit will remove the ring argument completely.
Fixes: 2320c9e6a768 ("drm/sched: memset() 'job' in drm_sched_job_init()") Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2ae520cb12831d264ceb97c61f72c59d33c0dbd7) Signed-off-by: Sasha Levin <sashal@kernel.org>
On gt reset, if a context is running, then accumulate it's active time
into the busyness counter since there will be no chance for the context
to switch out and update it's run time.
Active busyness of an engine is calculated using gt timestamp and the
context switch in time. While capturing the gt timestamp, it's possible
that the context switches out. This race could result in an active
busyness value that is greater than the actual context runtime value by a
small amount. This leads to a negative delta and throws off busyness
calculations for the user.
If a subsequent count is smaller than the previous one, just return the
previous one, since we expect the busyness to catch up.
On GT reset, we store total busyness counts for all engines and
re-register the utilization buffer with GuC. At that time we should
reset the buffer, so that we don't get spurious busyness counts on
subsequent queries.
To repro this issue, run igt@perf_pmu@busy-hang followed by
igt@perf_pmu@most-busy-idle-check-all for a couple iterations.
drm_mode_vrefresh() is trying to avoid divide by zero
by checking whether htotal or vtotal are zero. But we may
still end up with a div-by-zero of vtotal*htotal*...
Cc: stable@vger.kernel.org Reported-by: syzbot+622bba18029bcde672e1@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=622bba18029bcde672e1 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20241129042629.18280-2-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB-C monitor is connected directly to Intel Barlow Ridge host, it
goes into "redrive" mode that basically routes the DisplayPort signals
directly from the GPU to the USB-C monitor without any tunneling needed.
However, the host router must be powered on for this to work. Aaron
reported that there are a couple of cases where this will not work with
the current code:
- Booting with USB-C monitor plugged in.
- Plugging in USB-C monitor when the host router is in sleep state
(runtime suspended).
- Plugging in USB-C device while the system is in system sleep state.
In all these cases once the host router is runtime suspended the picture
on the connected USB-C display disappears too. This is certainly not
what the user expected.
For this reason improve the redrive mode handling to keep the host
router from runtime suspending when detect that any of the above cases
is happening.
Fixes: a75e0684efe5 ("thunderbolt: Keep the domain powered when USB4 port is in redrive mode") Reported-by: Aaron Rainbolt <arainbolt@kfocus.org> Closes: https://lore.kernel.org/linux-usb/20241009220118.70bfedd0@kf-ir16/ Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-------------------------------
| If Number | Function |
-------------------------------
| 2 | USB AP Log Port |
-------------------------------
| 3 | USB AP GNSS Port|
-------------------------------
| 4 | USB AP META Port|
-------------------------------
| 5 | ADB port |
-------------------------------
| 6 | USB MD AT Port |
------------------------------
| 7 | USB MD META Port|
-------------------------------
| 8 | USB NTZ Port |
-------------------------------
| 9 | USB Debug port |
-------------------------------
Signed-off-by: Jack Wu <wojackbb@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
