The theory behind vdso randomization is that it's mapped at a random
offset above the top of the stack. To avoid wasting a page of
memory for an extra page table, the vdso isn't supposed to extend
past the lowest PMD into which it can fit. Other than that, the
address should be a uniformly distributed address that meets all of
the alignment requirements.
The current algorithm is buggy: the vdso has about a 50% probability
of being at the very end of a PMD. The current algorithm also has a
decent chance of failing outright due to incorrect handling of the
case where the top of the stack is near the top of its PMD.
This fixes the implementation. The paxtest estimate of vdso
"randomisation" improves from 11 bits to 18 bits. (Disclaimer: I
don't know what the paxtest code is actually calculating.)
It's worth noting that this algorithm is inherently biased: the vdso
is more likely to end up near the end of its PMD than near the
beginning. Ideally we would either nix the PMD sharing requirement
or jointly randomize the vdso and the stack to reduce the bias.
In the mean time, this is a considerable improvement with basically
no risk of compatibility issues, since the allowed outputs of the
algorithm are unchanged.
As an easy test, doing this:
for i in `seq 10000`
do grep -P vdso /proc/self/maps |cut -d- -f1
done |sort |uniq -d
used to produce lots of output (1445 lines on my most recent run).
A tiny subset looks like this:
Symlink reading code does not check whether the resulting path fits into
the page provided by the generic code. This isn't as easy as just
checking the symlink size because of various encoding conversions we
perform on path. So we have to check whether there is still enough space
in the buffer on the fly.
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz>
[lizf: Backported to 3.4: udf_get_filename() is called in do_udf_readdir()] Signed-off-by: Zefan Li <lizefan@huawei.com>
UDF specification allows arbitrarily large symlinks. However we support
only symlinks at most one block large. Check the length of the symlink
so that we don't access memory beyond end of the symlink block.
Reported-by: Carl Henrik Lunde <chlunde@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Zefan Li <lizefan@huawei.com>
Verify that inode size is sane when loading inode with data stored in
ICB. Otherwise we may get confused later when working with the inode and
inode size is too big.
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz>
[lizf: Backported to 3.4: just return on error, as there's no "out" label] Signed-off-by: Zefan Li <lizefan@huawei.com>
We didn't check length of rock ridge ER records before printing them.
Thus corrupted isofs image can cause us to access and print some memory
behind the buffer with obvious consequences.
Reported-and-tested-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Zefan Li <lizefan@huawei.com>
For buffer write, page lock will be got in write_begin and released in
write_end, in ocfs2_write_end_nolock(), before it unlock the page in
ocfs2_free_write_ctxt(), it calls ocfs2_run_deallocs(), this will ask
for the read lock of journal->j_trans_barrier. Holding page lock and
ask for journal->j_trans_barrier breaks the locking order.
This will cause a deadlock with journal commit threads, ocfs2cmt will
get write lock of journal->j_trans_barrier first, then it wakes up
kjournald2 to do the commit work, at last it waits until done. To
commit journal, kjournald2 needs flushing data first, it needs get the
cache page lock.
Since some ocfs2 cluster locks are holding by write process, this
deadlock may hung the whole cluster.
unlock pages before ocfs2_run_deallocs() can fix the locking order, also
put unlock before ocfs2_commit_trans() to make page lock is unlocked
before j_trans_barrier to preserve unlocking order.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The Arcam rPAC seems to have the same problem - whenever anything
(alsamixer, udevd, 3.9+ kernel from 60af3d037eb8c, ..) attempts to
access mixer / control interface of the card, the firmware "locks up"
the entire device, resulting in
SNDRV_PCM_IOCTL_HW_PARAMS failed (-5): Input/output error
from alsa-lib.
Other operating systems can somehow read the mixer (there seems to be
playback volume/mute), but any manipulation is ignored by the device
(which has hardware volume controls).
This patch changes iscsit_do_tx_data() to fail on short writes
when kernel_sendmsg() returns a value different than requested
transfer length, returning -EPIPE and thus causing a connection
reset to occur.
This avoids a potential bug in the original code where a short
write would result in kernel_sendmsg() being called again with
the original iovec base + length.
In practice this has not been an issue because iscsit_do_tx_data()
is only used for transferring 48 byte headers + 4 byte digests,
along with seldom used control payloads from NOPIN + TEXT_RSP +
REJECT with less than 32k of data.
So following Al's audit of iovec consumers, go ahead and fail
the connection on short writes for now, and remove the bogus
logic ahead of his proper upstream fix.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Rock Ridge extensions define so called Continuation Entries (CE) which
define where is further space with Rock Ridge data. Corrupted isofs
image can contain arbitrarily long chain of these, including a one
containing loop and thus causing kernel to end in an infinite loop when
traversing these entries.
Limit the traversal to 32 entries which should be more than enough space
to store all the Rock Ridge data.
Reported-by: P J P <ppandit@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Zefan Li <lizefan@huawei.com>
When ring buffer returns an error indicating retry, storvsc may not
return a proper error code to SCSI when bounce buffer is not used.
This has introduced I/O freeze on RAID running atop storvsc devices.
This patch fixes it by always returning a proper error code.
Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Users have no business installing custom code segments into the
GDT, and segments that are not present but are otherwise valid
are a historical source of interesting attacks.
For completeness, block attempts to set the L bit. (Prior to
this patch, the L bit would have been silently dropped.)
This is an ABI break. I've checked glibc, musl, and Wine, and
none of them look like they'll have any trouble.
Note to stable maintainers: this is a hardening patch that fixes
no known bugs. Given the possibility of ABI issues, this
probably shouldn't be backported quickly.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: security@kernel.org <security@kernel.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Since the rework of the sparse interrupt code to actually free the
unused interrupt descriptors there exists a race between the /proc
interfaces to the irq subsystem and the code which frees the interrupt
descriptor.
/proc/interrupts is the only interface which can actively corrupt
kernel memory via the lock access. /proc/stat can only read from freed
memory. Extremly hard to trigger, but possible.
The interfaces in /proc/irq/N/ are not affected by this because the
removal of the proc file is serialized in procfs against concurrent
readers/writers. The removal happens before the descriptor is freed.
For architectures which have CONFIG_SPARSE_IRQ=n this is a non issue
as the descriptor is never freed. It's merely cleared out with the irq
descriptor lock held. So any concurrent proc access will either see
the old correct value or the cleared out ones.
Protect the lookup and access to the irq descriptor in
show_interrupts() with the sparse_irq_lock.
Provide kstat_irqs_usr() which is protecting the lookup and access
with sparse_irq_lock and switch /proc/stat to use it.
Document the existing kstat_irqs interfaces so it's clear that the
caller needs to take care about protection. The users of these
interfaces are either not affected due to SPARSE_IRQ=n or already
protected against removal.
Fixes: 1f5a5b87f78f "genirq: Implement a sane sparse_irq allocator" Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[lizf: Backported to 3.4:
- define kstat_irqs() for CONFIG_GENERIC_HARDIRQS
- add ifdef/endif CONFIG_SPARSE_IRQ] Signed-off-by: Zefan Li <lizefan@huawei.com>
If some error happens in NCP_IOC_SETROOT ioctl, the appropriate error
return value is then (in most cases) just overwritten before we return.
This can result in reporting success to userspace although error happened.
This bug was introduced by commit 2e54eb96e2c8 ("BKL: Remove BKL from
ncpfs"). Propagate the errors correctly.
Fixes: 2e54eb96e2c80 ("BKL: Remove BKL from ncpfs") Signed-off-by: Jan Kara <jack@suse.cz> Cc: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
When we abort a transaction we iterate over all the ranges marked as dirty
in fs_info->freed_extents[0] and fs_info->freed_extents[1], clear them
from those trees, add them back (unpin) to the free space caches and, if
the fs was mounted with "-o discard", perform a discard on those regions.
Also, after adding the regions to the free space caches, a fitrim ioctl call
can see those ranges in a block group's free space cache and perform a discard
on the ranges, so the same issue can happen without "-o discard" as well.
This causes corruption, affecting one or multiple btree nodes (in the worst
case leaving the fs unmountable) because some of those ranges (the ones in
the fs_info->pinned_extents tree) correspond to btree nodes/leafs that are
referred by the last committed super block - breaking the rule that anything
that was committed by a transaction is untouched until the next transaction
commits successfully.
I ran into this while running in a loop (for several hours) the fstest that
I recently submitted:
[PATCH] fstests: add btrfs test to stress chunk allocation/removal and fstrim
The corruption always happened when a transaction aborted and then fsck complained
like this:
_check_btrfs_filesystem: filesystem on /dev/sdc is inconsistent
*** fsck.btrfs output ***
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
read block failed check_tree_block
Couldn't open file system
In this case 94945280 corresponded to the root of a tree.
Using frace what I observed was the following sequence of steps happened:
1) transaction N started, fs_info->pinned_extents pointed to
fs_info->freed_extents[0];
4) transaction N commit starts, fs_info->pinned_extents now points to
fs_info->freed_extents[1], and transaction N completes;
5) transaction N + 1 starts;
6) eb is COWed, and btrfs_free_tree_block() called for this eb;
7) eb range (94945280 to 94945280 + 16Kb) is added to
fs_info->pinned_extents (fs_info->freed_extents[1]);
8) Something goes wrong in transaction N + 1, like hitting ENOSPC
for example, and the transaction is aborted, turning the fs into
readonly mode. The stack trace I got for example:
[112065.253935] [<ffffffff8140c7b6>] dump_stack+0x4d/0x66
[112065.254271] [<ffffffff81042984>] warn_slowpath_common+0x7f/0x98
[112065.254567] [<ffffffffa0325990>] ? __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.261674] [<ffffffff810429e5>] warn_slowpath_fmt+0x48/0x50
[112065.261922] [<ffffffffa032949e>] ? btrfs_free_path+0x26/0x29 [btrfs]
[112065.262211] [<ffffffffa0325990>] __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.262545] [<ffffffffa036b1d6>] btrfs_remove_chunk+0x537/0x58b [btrfs]
[112065.262771] [<ffffffffa033840f>] btrfs_delete_unused_bgs+0x1de/0x21b [btrfs]
[112065.263105] [<ffffffffa0343106>] cleaner_kthread+0x100/0x12f [btrfs]
(...)
[112065.264493] ---[ end trace dd7903a975a31a08 ]---
[112065.264673] BTRFS: error (device sdc) in btrfs_remove_chunk:2625: errno=-28 No space left
[112065.264997] BTRFS info (device sdc): forced readonly
9) The clear kthread sees that the BTRFS_FS_STATE_ERROR bit is set in
fs_info->fs_state and calls btrfs_cleanup_transaction(), which in
turn calls btrfs_destroy_pinned_extent();
10) Then btrfs_destroy_pinned_extent() iterates over all the ranges
marked as dirty in fs_info->freed_extents[], and for each one
it calls discard, if the fs was mounted with "-o discard", and
adds the range to the free space cache of the respective block
group;
11) btrfs_trim_block_group(), invoked from the fitrim ioctl code path,
sees the free space entries and performs a discard;
12) After an umount and mount (or fsck), our eb's location on disk was full
of zeroes, and it should have been untouched, because it was marked as
dirty in the fs_info->pinned_extents tree, and therefore used by the
trees that the last committed superblock points to.
Fix this by not performing a discard and not adding the ranges to the free space
caches - it's useless from this point since the fs is now in readonly mode and
we won't write free space caches to disk anymore (otherwise we would leak space)
nor any new superblock. By not adding the ranges to the free space caches, it
prevents other code paths from allocating that space and write to it as well,
therefore being safer and simpler.
When loading encrypted-keys module, if the last check of
aes_get_sizes() in init_encrypted() fails, the driver just returns an
error without unregistering its key type. This results in the stale
entry in the list. In addition to memory leaks, this leads to a kernel
crash when registering a new key type later.
This patch fixes the problem by swapping the calls of aes_get_sizes()
and register_key_type(), and releasing resources properly at the error
paths.
In snd_usbmidi_error_timer(), the driver tries to resubmit MIDI input
URBs to reactivate the MIDI stream, but this causes the error when
some of URBs are still pending like:
This patch sets the correct reverse sequence order to the instructions
set to run, when any failure occurs during the initialization steps.
It also adds the missing unregistration call of the can device if the
failure appears after having been registered.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patchs fixes a misplaced call to memset() that fills the request
buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT
requests, the content set by the caller was thus lost.
With this patch, the memory area is zeroed only when requesting info
from the device.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Check the that ring we are using for copies is functional
rather than the GFX ring. On newer asics we use the DMA
ring for bo moves.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The commit "vmwgfx: Rework fence event action" introduced a number of bugs
that are fixed with this commit:
a) A forgotten return stateemnt.
b) An if statement with identical branches.
Reported-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Kernel side fence objects are used when unbinding resources and may thus be
created as part of a memory reclaim operation. This might trigger recursive
memory reclaims and result in the kernel running out of stack space.
So a simple way out is to avoid accounting of these fence objects.
In principle this is OK since while user-space can trigger the creation of
such objects, it can't really hold on to them. However, their lifetime is
quite long, so some form of accounting should perhaps be implemented in the
future.
Fixes kernel crashes when running, for example viewperf11 ensight-04 test 3
with low system memory settings.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
There's an off-by-one bug in function __domain_mapping(), which may
trigger the BUG_ON(nr_pages < lvl_pages) when
(nr_pages + 1) & superpage_mask == 0
The issue was introduced by commit 9051aa0268dc "intel-iommu: Combine
domain_pfn_mapping() and domain_sg_mapping()", which sets sg_res to
"nr_pages + 1" to avoid some of the 'sg_res==0' code paths.
It's safe to remove extra "+1" because sg_res is only used to calculate
page size now.
Reported-And-Tested-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Dmitry Chernenkov used KASAN to discover that eCryptfs writes past the
end of the allocated buffer during encrypted filename decoding. This
fix corrects the issue by getting rid of the unnecessary 0 write when
the current bit offset is 2.
Signed-off-by: Michael Halcrow <mhalcrow@google.com> Reported-by: Dmitry Chernenkov <dmitryc@google.com> Suggested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch adds waiting until transmit buffer and shifter will be empty
before clock disabling.
Without this fix it's possible to have clock disabled while data was
not transmited yet, which causes unproper state of TX line and problems
in following data transfers.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Some boards with TC6393XB chip require full state restore during system
resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000
tosa is one of them). Failing to do so would result in ohci Oops on
resume due to internal memory contentes being changed. Fail ohci suspend
on tc6393xb is full state restore is required.
Recommended workaround is to unbind tmio-ohci driver before suspend and
rebind it after resume.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Make sure to check the version field of the firmware header to make sure to
not accidentally try to parse a firmware file with a different layout.
Trying to do so can result in loading invalid firmware code to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
We can get here from blkdev_ioctl() -> blkpg_ioctl() -> add_partition()
with a user passed in partno value. If we pass in 0x7fffffff, the
new target in disk_expand_part_tbl() overflows the 'int' and we
access beyond the end of ptbl->part[] and even write to it when we
do the rcu_assign_pointer() to assign the new partition.
Reported-by: David Ramos <daramos@stanford.edu> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
[lizf: Backported to 3.4: drop changes to esas2r_main.c] Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit 6ac665c63dca ("PCI: rewrite PCI BAR reading code") masked off
low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(),
which compares 'base == maxbase' to check for read-only BARs. The masking
of 'l' means that comparison will never be 'true', so the check for
read-only BARs no longer works.
Resolve this by also masking off the low-order bits of 'sz' before passing
it into pci_size() as 'maxbase'. With this change, pci_size() will once
again catch the problems that have been encountered to date:
- AGP aperture BAR of AMD-7xx host bridges: if the AGP window is
disabled, this BAR is read-only and read as 0x00000008 [1]
- BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1]
bus_find_device_by_name() acquires a device reference which is never
released. This results in an object leak, which on older kernels
results in failure to release all resources of PCI devices. libvirt
uses drivers_probe to re-attach devices to the host after assignment
and is therefore a common trigger for this leak.
The logic of vfree()'ing vol->upd_buf is tied to vol->updating.
In ubi_start_update() vol->updating is set long before vmalloc()'ing
vol->upd_buf. If we encounter a write failure in ubi_start_update()
before vmalloc() the UBI device release function will try to vfree()
vol->upd_buf because vol->updating is set.
Fix this by allocating vol->upd_buf directly after setting vol->updating.
This patch fixes an issue that the NULL pointer dereference happens
when we uses g_audio driver. Since the g_audio driver will call
usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(),
the uep->pipe of renesas usbhs driver will be NULL. So, this patch
adds a condition to avoid the oops.
After invoking ->dirty_inode(), __mark_inode_dirty() does smp_mb() and
tests inode->i_state locklessly to see whether it already has all the
necessary I_DIRTY bits set. The comment above the barrier doesn't
contain any useful information - memory barriers can't ensure "changes
are seen by all cpus" by itself.
And it sure enough was broken. Please consider the following
scenario.
CPU 0 CPU 1
-------------------------------------------------------------------------------
enters __writeback_single_inode()
grabs inode->i_lock
tests PAGECACHE_TAG_DIRTY which is clear
enters __set_page_dirty()
grabs mapping->tree_lock
sets PAGECACHE_TAG_DIRTY
releases mapping->tree_lock
leaves __set_page_dirty()
enters __mark_inode_dirty()
smp_mb()
sees I_DIRTY_PAGES set
leaves __mark_inode_dirty()
clears I_DIRTY_PAGES
releases inode->i_lock
Now @inode has dirty pages w/ I_DIRTY_PAGES clear. This doesn't seem
to lead to an immediately critical problem because requeue_inode()
later checks PAGECACHE_TAG_DIRTY instead of I_DIRTY_PAGES when
deciding whether the inode needs to be requeued for IO and there are
enough unintentional memory barriers inbetween, so while the inode
ends up with inconsistent I_DIRTY_PAGES flag, it doesn't fall off the
IO list.
The lack of explicit barrier may also theoretically affect the other
I_DIRTY bits which deal with metadata dirtiness. There is no
guarantee that a strong enough barrier exists between
I_DIRTY_[DATA]SYNC clearing and write_inode() writing out the dirtied
inode. Filesystem inode writeout path likely has enough stuff which
can behave as full barrier but it's theoretically possible that the
writeout may not see all the updates from ->dirty_inode().
Fix it by adding an explicit smp_mb() after I_DIRTY clearing. Note
that I_DIRTY_PAGES needs a special treatment as it always needs to be
cleared to be interlocked with the lockless test on
__mark_inode_dirty() side. It's cleared unconditionally and
reinstated after smp_mb() if the mapping still has dirty pages.
Also add comments explaining how and why the barriers are paired.
Lightly tested.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jan Kara <jack@suse.cz> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Instead of clearing I_DIRTY_PAGES and resetting it when we didn't succeed in
writing them all, just clear the bit only when we succeeded writing all the
pages. We also move the clearing of the bit close to other i_state handling to
separate it from writeback list handling. This is desirable because list
handling will differ for flusher thread and other writeback_single_inode()
callers in future. No filesystem plays any tricks with I_DIRTY_PAGES (like
checking it in ->writepages or ->write_inode implementation) so this movement
is safe.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The ecryptfs_encrypted_view mount option greatly changes the
functionality of an eCryptfs mount. Instead of encrypting and decrypting
lower files, it provides a unified view of the encrypted files in the
lower filesystem. The presence of the ecryptfs_encrypted_view mount
option is intended to force a read-only mount and modifying files is not
supported when the feature is in use. See the following commit for more
information:
This patch forces the mount to be read-only when the
ecryptfs_encrypted_view mount option is specified by setting the
MS_RDONLY flag on the superblock. Additionally, this patch removes some
broken logic in ecryptfs_open() that attempted to prevent modifications
of files when the encrypted view feature was in use. The check in
ecryptfs_open() was not sufficient to prevent file modifications using
system calls that do not operate on a file descriptor.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reported-by: Priya Bansal <p.bansal@samsung.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by: Hein Tibosch <hein_tibosch@yahoo.es> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled. Disable MSI.
Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
disabled NCQ on them. It turns out that NCQ is fine as long as MSI is
not used, so let's turn off MSI and leave NCQ on.
Signed-off-by: Tejun Heo <tj@kernel.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=60731 Tested-by: <dorin@i51.org> Tested-by: Imre Kaloz <kaloz@openwrt.org> Fixes: 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") Signed-off-by: Zefan Li <lizefan@huawei.com>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Kelley Nielsen <kelleynnn@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html
I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: Helge Deller <deller@gmx.de> Signed-off-by: Petr Mladek <pmladek@suse.cz> Tested-by: Petr Mladek <pmladek@suse.cz> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If SERIAL_8250 is compiled as a module, the platform specific setup
for Loongson will be a module too, and it will not work very well.
At least on Loongson 3 it will trigger a build failure,
since loongson_sysconf is not exported to modules.
Fix by making the platform specific serial code always built-in.
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[lizf: Backported to 3.4:
- adjust context
- s/AZX_GCAP_640K/ICH6_GCAP_64OK] Signed-off-by: Zefan Li <lizefan@huawei.com>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b44 ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4:
- adjust context
- drop changes to xhci_plat_suspend()] Signed-off-by: Zefan Li <lizefan@huawei.com>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
In some cases, the fcoe_rx_list may contains multiple instances
of the same skb (the so called "shared skbs").
the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list,
modifies (and destroys) its content and then proceed to the next one.
The problem is that if the skb is shared, the remaining instances will
be corrupted.
The solution is to use skb_share_check() before adding the skb to the
fcoe_rx_list.
This patch breaks the race condition by adding a retest of the bit
after the call to rpc_sleep_on().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Both xprt_lookup_rqst() and xprt_complete_rqst() require that you
take the transport lock in order to avoid races with xprt_transmit().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Reviewed-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes: 6b8f1ca5581b ("USB: ssu100: set tty_flags in ssu100_process_packet") Signed-off-by: Johan Hovold <johan@kernel.org>
[lizf: Backported to 3.4:
- adjust context
- lookup tty using tty_port_tty_get()] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org>
[lizf: Backported to 3.4:
- s/&port->port/tty/
- adjust context
- adjust indentation] Signed-off-by: Zefan Li <lizefan@huawei.com>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: For 3.2, net/ipv6/output_core.c is a completely new file] Signed-off-by: Zefan Li <lizefan@huawei.com>
With commits 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") and 04ca6973f7c1 ("ip: make IP identifiers less predictable"), IP
identifiers are generated from a counter chosen from an array of
counters indexed by the hash of the outgoing packet header's source
address, destination address, and protocol number. Thus, in
__ip_make_skb(), we must now call ip_select_ident() only after setting
these fields in the IP header to prevent IP identifiers from being
generated from bogus counters.
IP id sequence before fix: 18174, 5789, 5953, 59420, 59637, ...
After fix: 5967, 6185, 6374, 6600, 6795, 6892, 7051, 7288, ...
Signed-off-by: Jeffrey Knockel <jeffk@cs.unm.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Eric Dumazet <edumazet@google.com>
[Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
32-bit programs don't have an lm bit in their ABI, so they can't
reliably cause LDT_empty to return true without resorting to memset.
They shouldn't need to do this.
This should fix a longstanding, if minor, issue in all 64-bit kernels
as well as a potential regression in the TLS hardening code.
- Disables the F00F bug workaround warning. There is no F00F bug
workaround any more because Linux's standard IDT handling already
works around the F00F bug, but the warning still exists. This
is only cosmetic, and, in any event, there is no such thing as
KVM on a CPU with the F00F bug.
- Disables 32-bit APM BIOS detection. On a KVM paravirt system,
there should be no APM BIOS anyway.
- Disables tboot. I think that the tboot code should check the
CPUID hypervisor bit directly if it matters.
- paravirt_enabled disables espfix32. espfix32 should *not* be
disabled under KVM paravirt.
The last point is the purpose of this patch. It fixes a leak of the
high 16 bits of the kernel stack address on 32-bit KVM paravirt
guests. Fixes CVE-2014-8134.
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The WARN_ON checking whether i_mutex is held in
pagecache_isize_extended() was wrong because some filesystems (e.g.
XFS) use different locks for serialization of truncates / writes. So
just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- We didn't use the _ASM_EXTABLE macro
- Don't use __visible] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aafd668686239349ea58f3314ea2af86b Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- Keep using the paranoiderrorentry macro to generate the asm code
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- No need to define trace_stack_segment
- Use the errorentry macro to generate #SS asm code
- Adjust context
- Checked that this matches Luis's backport for Ubuntu] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch replaces the kfree_skb() by dev_kfree_skb_any().
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dave Hansen <dave@sr71.net> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: x86@kernel.org Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi> Debugged-by: Antti S. Lankila <alankila@bel.fi> Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
FSI doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
It is not guaranteed to that srp_sq_size is supported
by the HCA. So if we failed to create the QP with ENOMEM,
try with a smaller srp_sq_size. Keep it up until we hit
MIN_SRPT_SQ_SIZE, then fail the connection.
Reported-by: Mark Lehrer <lehrer@gmail.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Large (greater than 32k, the value of PAGE_ALLOC_COSTLY_ORDER) auth
tickets will have their buffers vmalloc'ed, which leads to the
following crash in crypto:
NFSv4.0 does not have TEST_STATEID/FREE_STATEID functionality, so
unlike NFSv4.1, the recovery procedure when stateids have expired or
have been revoked requires us to just forget the delegation.
http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Variable 'err' needn't be initialized when nfs_getattr() uses it to
check whether it should call generic_fillattr() or not. That can result
in spurious error returns. Initialize 'err' properly.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Audit rules disappear when an inode they watch is evicted from the cache.
This is likely not what we want.
The guilty commit is "fsnotify: allow marks to not pin inodes in core",
which didn't take into account that audit_tree adds watches with a zero
mask.
Adding any mask should fix this.
Fixes: 90b1e7a57880 ("fsnotify: allow marks to not pin inodes in core") Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
projects / thirdparty / kernel / stable.git / log
