The infamous commit c440eee1a7a1 ("Staging: staging: fbtft: Switch to
the GPIO descriptor interface") broke GPIO handling completely.
It has already four commits to rectify and it seems not enough.
In order to fix the mess here we:
1) Set default to "inactive" for all requested pins
2) Fix CS#, RD#, and WR# pins polarity since it's active low
and GPIO descriptor interface takes it into consideration
from the Device Tree or ACPI
3) Consolidate chip activation (CS# assertion) under default
->reset() callback
To summarize the expectations about polarity for GPIOs:
RD# Low
WR# Low
CS# Low
RESET# Low
DC or RS High
RW High
Data 0 .. 15 High
See also Adafruit learning course [1] for the example of the schematics.
While at it, drop unneeded NULL checks, since GPIO API is tolerant to that.
When 32-bit MIPS huge page support is enabled, we halve the number of
pointers a PTE page holds, making its last half go to waste.
Correspondingly, we should halve the number of kmap entries, as we just
initialized only a single pte table for that in pagetable_init().
The "dev->port[i].mp.mpi" is set to NULL during mlx5_ib_unbind_slave_port()
execution, however that field is needed to add device to unaffiliated list.
Such flow causes to the following kernel panic while unloading mlx5_ib
module in multi-port mode, hence the device should be added to the list
prior to unbind call.
What's more, alloc_skb_fclone() will call SKB_DATA_ALIGN for data size,
and it's not necessary to make alignment for buf_size in
tipc_buf_acquire(). So, just remove it.
Fixes: 4c94cc2d3d57 ("tipc: fall back to smaller MTU if allocation of local send skb fails") Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported warning in tcindex_alloc_perfect_hash. The problem
was in too big cp->hash, which triggers warning in kmalloc. Since
cp->hash comes from userspace, there is no need to warn if value
is not correct
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()") Reported-and-tested-by: syzbot+1071ad60cd7df39fdadb@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Acked-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 14972cbd34ff ("net: lwtunnel: Handle fragmentation") moved
fragmentation logic away from lwtunnel by carry encap headroom and
use it in output MTU calculation. But the forwarding part was not
covered and created difference in MTU for output and forwarding and
further to silent drops on ipv4 forwarding path. Fix it by taking
into account lwtunnel encap headroom.
The same commit also introduced difference in how to treat RTAX_MTU
in IPv4 and IPv6 where latter explicitly removes lwtunnel encap
headroom from route MTU. Make IPv4 version do the same.
Fixes: 14972cbd34ff ("net: lwtunnel: Handle fragmentation") Suggested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The caller of wb_get_create() should pin the memcg, because
wb_get_create() relies on this guarantee. The rcu read lock
only can guarantee that the memcg css returned by css_from_id()
cannot be released, but the reference of the memcg can be zero.
rcu_read_lock()
memcg_css = css_from_id()
wb_get_create(memcg_css)
cgwb_create(memcg_css)
// css_get can change the ref counter from 0 back to 1
css_get(memcg_css)
rcu_read_unlock()
Fix it by holding a reference to the css before calling
wb_get_create(). This is not a problem I encountered in the
real world. Just the result of a code review.
Fixes: 682aa8e1a6a1 ("writeback: implement unlocked_inode_to_wb transaction and use it for stat updates") Link: https://lore.kernel.org/r/20210402091145.80635-1-songmuchun@bytedance.com Signed-off-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 4c5de127598e1 ("bpf: Emit explicit NULL pointer checks for PROBE_LDX
instructions.") is emitting a couple of instructions before the actual load.
Consider those additional instructions while calculating extable offset.
Fixes: 4c5de127598e1 ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210622110026.1157847-1-ravi.bangoria@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the default register settings to include the VCO_RESET_CALCODE
settings (set by the SiLabs ClockBuilder software but not described in
the datasheet). Also update part of the initialization sequence to match
ClockBuilder and the datasheet.
If the Si5341 is being initially programmed and has no stored NVM
configuration, some of the register contents may contain unexpected
values, such as zeros, which could cause divide by zero errors during
driver initialization. Trap errors caused by zero registers or zero clock
rates which could result in divide errors later in the code.
The Si5341 datasheet warns that before accessing any other registers,
including the PAGE register, we need to wait for the DEVICE_READY register
to indicate the device is ready, or the process of the device loading its
state from NVM can be corrupted. Wait for DEVICE_READY on startup before
continuing initialization. This is done using a raw I2C register read
prior to setting up regmap to avoid any potential unwanted automatic PAGE
register accesses from regmap at this stage.
Caught this when looking at alpha-pll code. Untested but it is clear that
this was intended to write to PLL_CAL_L_VAL and not PLL_ALPHA_VAL.
Fixes: 691865bad627 ("clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20210609022852.4151-1-jonathan@marek.ca Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are a few issues with the setup of the Actions Semi Owl S500 SoC's
clock chain involving AHPPREDIV, H and AHB clocks:
* AHBPREDIV clock is defined as a muxer only, although it also acts as
a divider.
* H clock is using a wrong divider register offset
* AHB is defined as a multi-rate factor clock, but it is actually just
a fixed pass clock.
Let's provide the following fixes:
* Change AHBPREDIV clock to an ungated OWL_COMP_DIV definition.
* Use the correct register shift value in the OWL_DIVIDER definition
for H clock
* Drop the unneeded 'ahb_factor_table[]' and change AHB clock to an
ungated OWL_COMP_FIXED_FACTOR definition.
The following clocks of the Actions Semi Owl S500 SoC have been defined
to use a shared clock factor table 'bisp_factor_table[]': DE[1-2], VCE,
VDE, BISP, SENSOR[0-1]
There are several issues involved in this approach:
* 'bisp_factor_table[]' describes the configuration of a regular 8-rates
divider, so its usage is redundant. Additionally, judging by the BISP
clock context, it is incomplete since it maps only 8 out of 12
possible entries.
* The clocks mentioned above are not identical in terms of the available
rates, therefore cannot rely on the same factor table. Specifically,
BISP and SENSOR* are standard 12-rate dividers so their configuration
should rely on a proper clock div table, while VCE and VDE require a
factor table that is a actually a subset of the one needed for DE[1-2]
clocks.
Let's fix this by implementing the following:
* Add new factor tables 'de_factor_table' and 'hde_factor_table' to
properly handle DE[1-2], VCE and VDE clocks.
* Add a common div table 'std12rate_div_table' for BISP and SENSOR[0-1]
clocks converted to OWL_COMP_DIV.
* Drop the now unused 'bisp_factor_table[]'.
Additionally, drop the CLK_IGNORE_UNUSED flag for SENSOR[0-1] since
there is no reason to always keep ON those clocks.
Error status of this event means that it has ended due reasons other
than a connection:
'If advertising has terminated as a result of the advertising duration
elapsing, the Status parameter shall be set to the error code
Advertising Timeout (0x3C).'
'If advertising has terminated because the
Max_Extended_Advertising_Events was reached, the Status parameter
shall be set to the error code Limit Reached (0x43).'
Fixes: acf0aeae431a0 ("Bluetooth: Handle ADv set terminated event") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
These command do have variable length and the length can go up to 251,
so this changes the struct to not use a fixed size and then when
creating the PDU only the actual length of the data send to the
controller.
Fixes: a0fb3726ba551 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add Advertising - Success (ScRsp only) - run
Sending Add Advertising (0x003e)
Test condition added, total 1
[ 11.004577] ==================================================================
[ 11.005292] BUG: KASAN: slab-out-of-bounds in tlv_data_is_valid+0x87/0xe0
[ 11.005984] Read of size 1 at addr ffff888002c695b0 by task mgmt-tester/87
[ 11.006711]
[ 11.007176]
[ 11.007429] Allocated by task 87:
[ 11.008151]
[ 11.008438] The buggy address belongs to the object at ffff888002c69580
[ 11.008438] which belongs to the cache kmalloc-64 of size 64
[ 11.010526] The buggy address is located 48 bytes inside of
[ 11.010526] 64-byte region [ffff888002c69580, ffff888002c695c0)
[ 11.012423] The buggy address belongs to the page:
[ 11.013291]
[ 11.013544] Memory state around the buggy address:
[ 11.014359] ffff888002c69480: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.015453] ffff888002c69500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.016232] >ffff888002c69580: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.017010] ^
[ 11.017547] ffff888002c69600: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.018296] ffff888002c69680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.019116] ==================================================================
Patch was based on wrong presumption that be_poll can be called only
from bh context. It reintroducing old regression (also reverted) and
causing deadlock when we use netconsole with benet in bonding.
Fixes: d0d006a43e9a7a ("be2net: disable bh with spin_lock in be_process_mcc") Signed-off-by: Petr Oros <poros@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
An approximation for the PacketLifeTime is half the local ACK timeout.
The encoding for both timers are logarithmic.
If the local ACK timeout is set, but zero, it means the timer is
disabled. In this case, we choose the CMA_IBOE_PACKET_LIFETIME value,
since 50% of infinite makes no sense.
Before this commit, the PacketLifeTime became 255 if local ACK
timeout was zero (not running).
Fixed by explicitly testing for timeout being zero.
Fixes: e1ee1e62bec4 ("RDMA/cma: Use ACK timeout for RoCE packetLifeTime") Link: https://lore.kernel.org/r/1624371207-26710-1-git-send-email-haakon.bugge@oracle.com Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per the kmsg document [0], if we don't specify the log level with a
prefix "<N>" in the message string, the default log level will be
applied to the message. Since the default level could be warning(4),
this would make the log utility such as journalctl treat the message,
"Started bpfilter", as a warning. To avoid confusion, this commit
adds the prefix "<5>" to make the message always a notice.
priv->cbs is an array of priv->info->num_cbs_shapers elements of type
struct sja1105_cbs_entry which only get allocated if CONFIG_NET_SCH_CBS
is enabled.
However, sja1105_reload_cbs() is called from sja1105_static_config_reload()
which in turn is called for any of the items in sja1105_reset_reasons,
therefore during the normal runtime of the driver and not just from a
code path which can be triggered by the tc-cbs offload.
The sja1105_reload_cbs() function does not contain a check whether the
priv->cbs array is NULL or not, it just assumes it isn't and proceeds to
iterate through the credit-based shaper elements. This leads to a NULL
pointer dereference.
The solution is to return success if the priv->cbs array has not been
allocated, since sja1105_reload_cbs() has nothing to do.
Fixes: 4d7525085a9b ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Complete to commit def4ec6dce393e ("e1000e: PCIm function state support")
Check the PCIm state only on CSME systems. There is no point to do this
check on non CSME systems.
This patch fixes a generation a false-positive warning:
"Error in exiting dmoff"
Fixes: def4ec6dce39 ("e1000e: PCIm function state support") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
First problem is that optlen is fetched without checking
there is more than one byte to parse.
Fix this by taking care of IPV6_TLV_PAD1 before
fetching optlen (under appropriate sanity checks against len)
Second problem is that IPV6_TLV_PADN checks of zero
padding are performed before the check of remaining length.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: c1412fce7ecc ("net/ipv6/exthdrs.c: Strict PadN option checking") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The key length used to store the macsec key was set to MACSEC_KEYID_LEN
(16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN instead (the max length accepted in
uAPI).
Fixes: 27736563ce32 ("net: atlantic: MACSec egress offload implementation") Fixes: 9ff40a751a6f ("net: atlantic: MACSec ingress offload implementation") Reported-by: Lior Nahmanson <liorna@nvidia.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The key length used to store the macsec key was set to MACSEC_KEYID_LEN
(16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN instead (the max length accepted in
uAPI).
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support") Reported-by: Lior Nahmanson <liorna@nvidia.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The key length used when offloading macsec to Ethernet or PHY drivers
was set to MACSEC_KEYID_LEN (16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN to store the key (the max length
accepted in uAPI) and secy->key_len to copy it.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure") Reported-by: Lior Nahmanson <liorna@nvidia.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct rdma_id_private contains three bit-fields, tos_set,
timeout_set, and min_rnr_timer_set. These are set by accessor functions
without any synchronization. If two or all accessor functions are invoked
in close proximity in time, there will be Read-Modify-Write from several
contexts to the same variable, and the result will be intermittent.
Fixed by protecting the bit-fields by the qp_mutex in the accessor
functions.
The consumer of timeout_set and min_rnr_timer_set is in
rdma_init_qp_attr(), which is called with qp_mutex held for connected
QPs. Explicit locking is added for the consumers of tos and tos_set.
This commit depends on ("RDMA/cma: Remove unnecessary INIT->INIT
transition"), since the call to rdma_init_qp_attr() from
cma_init_conn_qp() does not hold the qp_mutex.
Fixes: 2c1619edef61 ("IB/cma: Define option to set ack timeout and pack tos_set") Fixes: 3aeffc46afde ("IB/cma: Introduce rdma_set_min_rnr_timer()") Link: https://lore.kernel.org/r/1624369197-24578-3-git-send-email-haakon.bugge@oracle.com Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Free tx_pool and clear it, if allocation of tso_pool fails.
release_tx_pools() assumes we have both tx and tso_pools if ->tx_pool is
non-NULL. If allocation of tso_pool fails in init_tx_pools(), the assumption
will not be true and we would end up dereferencing ->tx_buff, ->free_map
fields from a NULL pointer.
Fixes: 3205306c6b8d ("ibmvnic: Update TX pool initialization routine") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
free_long_term_buff() checks ltb->buff to decide whether we have a long
term buffer to free. So set ltb->buff to NULL afer freeing. While here,
also clear ->map_id, fix up some coding style and log an error.
Fixes: 9c4eaabd1bb39 ("Check CRQ command return codes") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a crash in replenish_rx_pool() when called from ibmvnic_poll()
after a previous call to replenish_rx_pool() encountered an error when
allocating a socket buffer.
Thanks to Rick Lindsley and Dany Madden for helping debug the crash.
Fixes: 4f0b6812e9b9 ("ibmvnic: Introduce batched RX buffer descriptor transmission") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We batch subordinate command response queue (scrq) descriptors that we
need to send to the VIOS using an "indirect" buffer. If after we queue
one or more scrqs in the indirect buffer encounter an error (say fail
to allocate an skb), we leave the queued scrq descriptors in the
indirect buffer until the next call to ibmvnic_xmit().
On the next call to ibmvnic_xmit(), it is possible that the adapter is
going through a reset and it is possible that the long term buffers
have been unmapped on the VIOS side. If we proceed to flush (send) the
packets that are in the indirect buffer, we will end up using the old
map ids and this can cause the VIOS to trigger an unnecessary FATAL
error reset.
Instead of flushing packets remaining on the indirect_buff, discard
(clean) them instead.
Fixes: 0d973388185d4 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a vnic interface is taken down and then up, connectivity is not
restored. We bisected it to this commit. Reverting this commit until
we can fully investigate the issue/benefit of the change.
Fixes: 7c451f3ef676 ("ibmvnic: remove duplicate napi_schedule call in open function") Reported-by: Cristobal Forno <cforno12@linux.ibm.com> Reported-by: Abdul Haleem <abdhalee@in.ibm.com> Signed-off-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We tried to optimize the number of hcalls we send and skipped sending
the REQUEST_MAP calls for some maps. However during resets, we need to
resend all the maps to the VIOS since the VIOS does not remember the
old values. In fact we may have failed over to a new VIOS which will
not have any of the mappings.
When we send packets with map ids the VIOS does not know about, it
triggers a FATAL reset. While the client does recover from the FATAL
error reset, we are seeing a large number of such resets. Handling
FATAL resets is lot more unnecessary work than issuing a few more
hcalls so revert the commit and resend the maps to the VIOS.
Fixes: 1c7d45e7b2c ("ibmvnic: simplify reset_long_term_buff function") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When vsi->type == I40E_VSI_FDIR, we have caught the return value of
i40e_vsi_request_irq() but without further handling. Check and execute
memory clean on failure just like the other i40e_vsi_request_irq().
Fixes: 8a9eb7d3cbcab ("i40e: rework fdir setup and teardown") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is technically a backwards incompatible change in behaviour, but I'm
going to argue that it is very unlikely to break things, and likely to fix
*far* more then it breaks.
In no particular order, various reasons follow:
(a) I've long had a bug assigned to myself to debug a super rare kernel crash
on Android Pixel phones which can (per stacktrace) be traced back to BPF clat
IPv6 to IPv4 protocol conversion causing some sort of ugly failure much later
on during transmit deep in the GSO engine, AFAICT precisely because of this
change to gso_size, though I've never been able to manually reproduce it. I
believe it may be related to the particular network offload support of attached
USB ethernet dongle being used for tethering off of an IPv6-only cellular
connection. The reason might be we end up with more segments than max permitted,
or with a GSO packet with only one segment... (either way we break some
assumption and hit a BUG_ON)
(b) There is no check that the gso_size is > 20 when reducing it by 20, so we
might end up with a negative (or underflowing) gso_size or a gso_size of 0.
This can't possibly be good. Indeed this is probably somehow exploitable (or
at least can result in a kernel crash) by delivering crafted packets and perhaps
triggering an infinite loop or a divide by zero... As a reminder: gso_size (MSS)
is related to MTU, but not directly derived from it: gso_size/MSS may be
significantly smaller then one would get by deriving from local MTU. And on
some NICs (which do loose MTU checking on receive, it may even potentially be
larger, for example my work pc with 1500 MTU can receive 1520 byte frames [and
sometimes does due to bugs in a vendor plat46 implementation]). Indeed even just
going from 21 to 1 is potentially problematic because it increases the number
of segments by a factor of 21 (think DoS, or some other crash due to too many
segments).
(c) It's always safe to not increase the gso_size, because it doesn't result in
the max packet size increasing. So the skb_increase_gso_size() call was always
unnecessary for correctness (and outright undesirable, see later). As such the
only part which is potentially dangerous (ie. could cause backwards compatibility
issues) is the removal of the skb_decrease_gso_size() call.
(d) If the packets are ultimately destined to the local device, then there is
absolutely no benefit to playing around with gso_size. It only matters if the
packets will egress the device. ie. we're either forwarding, or transmitting
from the device.
(e) This logic only triggers for packets which are GSO. It does not trigger for
skbs which are not GSO. It will not convert a non-GSO MTU sized packet into a
GSO packet (and you don't even know what the MTU is, so you can't even fix it).
As such your transmit path must *already* be able to handle an MTU 20 bytes
larger then your receive path (for IPv4 to IPv6 translation) - and indeed 28
bytes larger due to IPv4 fragments. Thus removing the skb_decrease_gso_size()
call doesn't actually increase the size of the packets your transmit side must
be able to handle. ie. to handle non-GSO max-MTU packets, the IPv4/IPv6 device/
route MTUs must already be set correctly. Since for example with an IPv4 egress
MTU of 1500, IPv4 to IPv6 translation will already build 1520 byte IPv6 frames,
so you need a 1520 byte device MTU. This means if your IPv6 device's egress
MTU is 1280, your IPv4 route must be 1260 (and actually 1252, because of the
need to handle fragments). This is to handle normal non-GSO packets. Thus the
reduction is simply not needed for GSO packets, because when they're correctly
built, they will already be the right size.
(f) TSO/GSO should be able to exactly undo GRO: the number of packets (TCP
segments) should not be modified, so that TCP's MSS counting works correctly
(this matters for congestion control). If protocol conversion changes the
gso_size, then the number of TCP segments may increase or decrease. Packet loss
after protocol conversion can result in partial loss of MSS segments that the
sender sent. How's the sending TCP stack going to react to receiving ACKs/SACKs
in the middle of the segments it sent?
(g) skb_{decrease,increase}_gso_size() are already no-ops for GSO_BY_FRAGS
case (besides triggering WARN_ON_ONCE). This means you already cannot guarantee
that gso_size (and thus resulting packet MTU) is changed. ie. you must assume
it won't be changed.
(h) changing gso_size is outright buggy for UDP GSO packets, where framing
matters (I believe that's also the case for SCTP, but it's already excluded
by [g]). So the only remaining case is TCP, which also doesn't want it
(see [f]).
(i) see also the reasoning on the previous attempt at fixing this
(commit fa7b83bf3b156c767f3e4a25bbf3817b08f3ff8e) which shows that the current
behaviour causes TCP packet loss:
In the forwarding path GRO -> BPF 6 to 4 -> GSO for TCP traffic, the
coalesced packet payload can be > MSS, but < MSS + 20.
bpf_skb_proto_6_to_4() will upgrade the MSS and it can be > the payload
length. After then tcp_gso_segment checks for the payload length if it
is <= MSS. The condition is causing the packet to be dropped.
If optval != NULL and optlen == 0 are specified for SO_J1939_FILTER in
j1939_sk_setsockopt(), memdup_sockptr() will return ZERO_PTR for 0
size allocation. The new filter will be mistakenly assigned ZERO_PTR.
This patch checks for optlen != 0 and filter will be assigned NULL in
case of optlen == 0.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/r/20210620123842.117975-1-nslusarek@gmx.net Signed-off-by: Norbert Slusarek <nslusarek@gmx.net> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
I see no reason why max_dst_opts_cnt and max_hbh_opts_cnt
are fetched from the initial net namespace.
The other sysctls (max_dst_opts_len & max_hbh_opts_len)
are in fact already using the current ns.
Note: it is not clear why ipv6_destopt_rcv() use two ways to
get to the netns :
1) dev_net(dst->dev)
Originally used to increment IPSTATS_MIB_INHDRERRORS
2) dev_net(skb->dev)
Tom used this variant in his patch.
Maybe this calls to use ipv6_skb_net() instead ?
Fixes: 47d3d7ac656a ("ipv6: Implement limits on Hop-by-Hop and Destination options") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@quantonium.net> Cc: Coco Li <lixiaoyan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to avoid the issue.
Fixes: 9a4e79697009 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver") Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485 Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error code returned by platform_get_irq() is stored in 'irq', it's
forgotten to be copied to 'ret' before being returned. As a result, the
value 0 of 'ret' is returned incorrectly.
After the above fix is completed, initializing the local variable 'ret'
to 0 is no longer needed, remove it.
In addition, when dpu_mdss_init() is successfully returned, the value of
'ret' is always 0. Therefore, replace "return ret" with "return 0" to make
the code clearer.
Fixes: 070e64dc1bbc ("drm/msm/dpu: Convert to a chained irq chip") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20210510063805.3262-2-thunder.leizhen@huawei.com Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
irq_hpd interrupt should be handled after dongle plugged in and
before dongle unplugged. Hence irq_hpd interrupt is enabled at
the end of the plugin handle and disabled at the beginning of
unplugged handle. Current irq_hpd with sink_count = 0 is wrongly
handled same as the dongle unplugged which tears down the mainlink
and disables the phy. This patch fixes this problem by only tearing
down the mainlink but keeping phy enabled at irq_hpd with
sink_count = 0 handle so that next irq_hpd with sink_count =1 can be
handled by setup mainlink only. This patch also set dongle into D3
(power off) state at end of handling irq_hpd with sink_count = 0.
Changes in v2:
-- add ctrl->phy_Power_count
Changes in v3:
-- del ctrl->phy_Power_count
-- add phy_power_off to dp_ctrl_off_link_stream()
Changes in v4:
-- return immediately if clock disable failed at dp_ctrl_off_link_stream()
Changes in v5:
-- set dongle to D3 (power off) state at dp_ctrl_off_link_stream()
Changes in v6:
-- add Fixes tag
Fixes: ea9f337ce81e ("drm/msm/dp: reset dp controller only at boot up and pm_resume") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1621635930-30161-1-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sub-programs prog->aux->poke_tab[] is populated in jit_subprogs() and
then used when emitting 'BPF_JMP|BPF_TAIL_CALL' insn->code from the
individual JITs. The poke_tab[] to use is stored in the insn->imm by
the code adding it to that array slot. The JIT then uses imm to find the
right entry for an individual instruction. In the x86 bpf_jit_comp.c
this is done by calling emit_bpf_tail_call_direct with the poke_tab[]
of the imm value.
However, we observed the below null-ptr-deref when mixing tail call
programs with subprog programs. For this to happen we just need to
mix bpf-2-bpf calls and tailcalls with some extra calls or instructions
that would be patched later by one of the fixup routines. So whats
happening?
Before the fixup_call_args() -- where the jit op is done -- various
code patching is done by do_misc_fixups(). This may increase the
insn count, for example when we patch map_lookup_up using map_gen_lookup
hook. This does two things. First, it means the instruction index,
insn_idx field, of a tail call instruction will move by a 'delta'.
Then subprog start values subprog_info[i].start will be updated
with the delta and any poke descriptor index will also be updated
with the delta in adjust_poke_desc(). If we look at the adjust
subprog starts though we see its only adjusted when the delta
occurs before the new instructions,
/* NOTE: fake 'exit' subprog should be updated as well. */
for (i = 0; i <= env->subprog_cnt; i++) {
if (env->subprog_info[i].start <= off)
continue;
Earlier subprograms are not changed because their start values
are not moved. But, adjust_poke_desc() does the offset + delta
indiscriminately. The result is poke descriptors are potentially
corrupted.
Then in jit_subprogs() we only populate the poke_tab[]
when the above insn_idx is less than the next subprogram start. From
above we corrupted our insn_idx so we might incorrectly assume a
poke descriptor is not used in a subprogram omitting it from the
subprogram. And finally when the jit runs it does the deref of poke_tab
when emitting the instruction and crashes with below. Because earlier
step omitted the poke descriptor.
The fix is straight forward with above context. Simply move same logic
from adjust_subprog_starts() into adjust_poke_descs() and only adjust
insn_idx when needed.
[ 82.396354] bpf_testmod: version magic '5.12.0-rc2alu+ SMP preempt mod_unload ' should be '5.12.0+ SMP preempt mod_unload '
[ 82.623001] loop10: detected capacity change from 0 to 8
[ 88.487424] ==================================================================
[ 88.487438] BUG: KASAN: null-ptr-deref in do_jit+0x184a/0x3290
[ 88.487455] Write of size 8 at addr 0000000000000008 by task test_progs/5295
[ 88.487471] CPU: 7 PID: 5295 Comm: test_progs Tainted: G I 5.12.0+ #386
[ 88.487483] Hardware name: Dell Inc. Precision 5820 Tower/002KVM, BIOS 1.9.2 01/24/2019
[ 88.487490] Call Trace:
[ 88.487498] dump_stack+0x93/0xc2
[ 88.487515] kasan_report.cold+0x5f/0xd8
[ 88.487530] ? do_jit+0x184a/0x3290
[ 88.487542] do_jit+0x184a/0x3290
...
[ 88.487709] bpf_int_jit_compile+0x248/0x810
...
[ 88.487765] bpf_check+0x3718/0x5140
...
[ 88.487920] bpf_prog_load+0xa22/0xf10
Fixes: a748c6975dea3 ("bpf: propagate poke descriptors to subprograms") Reported-by: Jussi Maki <joamaki@gmail.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
No matter from hwsim_remove or hwsim_del_radio_nl, hwsim_del fails to
remove the entry in the edges list. Take the example below, phy0, phy1
and e0 will be deleted, resulting in e1 not freed and accessed in the
future.
This is because k3_cppi_desc_pool_destroy() which is called after
k3_udma_glue_release_tx_chn() in am65_cpsw_nuss_remove_tx_chns()
references struct device that is unregistered at the end of
k3_udma_glue_release_tx_chn()
Therefore the right order is to call k3_cppi_desc_pool_destroy() and
destroy desc pool before calling k3_udma_glue_release_tx_chn().
Fix this throughout the driver.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Resetting software indexes in bcm4908_dma_alloc_buf_descs() is not
enough as it's called during device probe only. Driver resets DMA on
every .ndo_open callback and it's required to reset indexes then.
This fixes inconsistent rings state and stalled traffic after interface
down & up sequence.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing source address validation, the flowi4 struct used for
fib_lookup should be in the reverse direction to the given skb.
fl4_dport and fl4_sport returned by fib4_rules_early_flow_dissect
should thus be swapped.
Fixes: 5a847a6e1477 ("net/ipv4: Initialize proto and ports in flow struct") Signed-off-by: Miao Wang <shankerwangmiao@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6c11fbf97e69 ("ip6_tunnel: add MPLS transmit support")
moved assiging inner_ipproto down from ipxip6_tnl_xmit() to
its callee ip6_tnl_xmit(). The latter is also used by GRE.
Since commit 38720352412a ("gre: Use inner_proto to obtain inner
header protocol") GRE had been depending on skb->inner_protocol
during segmentation. It sets it in gre_build_header() and reads
it in gre_gso_segment(). Changes to ip6_tnl_xmit() overwrite
the protocol, resulting in GSO skbs getting dropped.
Note that inner_protocol is a union with inner_ipproto,
GRE uses the former while the change switched it to the latter
(always setting it to just IPPROTO_GRE).
Restore the original location of skb_set_inner_ipproto(),
it is unclear why it was moved in the first place.
Fixes: 6c11fbf97e69 ("ip6_tunnel: add MPLS transmit support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f964050 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps") Fixes: 99c51064fb06 ("devmap: Use bpf_map_area_alloc() for allocating hash buckets") Fixes: 546ac1ffb70d ("bpf: add devmap, a map for storing net device references") Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, we use value from 2 seconds ago to decide
whether we should do lc calibration.
Although this don't happen frequently, fix flow to the way it should be.
Fixes: 7ae7784ec2a8 ("rtw88: 8822c: add LC calibration for RTL8822C") Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210426013252.5665-3-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit d37300ed1821 ("bpf: program: Refuse non-O_RDWR flags
in BPF_OBJ_GET"). It breaks Android userspace which expects to be able to
fetch programs with just read permissions.
Side-note: another option to fix it would be to extend bpf_prog_new_fd()
and to pass in used file mode flags in the same way as we do for maps via
bpf_map_new_fd(). Meaning, they'd end up in anon_inode_getfd() and thus
would be retained for prog fd operations with bpf() syscall. Right now
these flags are not checked with progs since they are immutable for their
lifetime (as opposed to maps which can be updated from user space). In
future this could potentially change with new features, but at that point
it's still fine to do the bpf_prog_new_fd() extension when needed. For a
simple stable fix, a revert is less churn.
Fixes: d37300ed1821 ("bpf: program: Refuse non-O_RDWR flags in BPF_OBJ_GET") Signed-off-by: Maciej Żenczykowski <maze@google.com>
[ Daniel: added side-note to commit message ] Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Lorenz Bauer <lmb@cloudflare.com> Acked-by: Greg Kroah-Hartman <gregkh@google.com> Link: https://lore.kernel.org/bpf/20210618105526.265003-1-zenczykowski@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
nft_table_lookup() allows us to obtain the table object by the name and
the family. The netlink portID validation needs to be skipped for the
dump path, since the ownership only applies to commands to update the
given table. Skip validation if the specified netlink PortID is zero
when calling nft_table_lookup().
In case of xfrm offload, if xdo_dev_state_add() of driver returns
-EOPNOTSUPP, xfrm offload fallback is failed.
In xfrm state_add() both xso->dev and xso->real_dev are initialized to
dev and when err(-EOPNOTSUPP) is returned only xso->dev is set to null.
So in this scenario the condition in func validate_xmit_xfrm(),
if ((x->xso.dev != dev) && (x->xso.real_dev == dev))
return skb;
returns true, due to which skb is returned without calling esp_xmit()
below which has fallback code. Hence the CRYPTO_FALLBACK is failing.
So fixing this with by keeping x->xso.real_dev as NULL when err is
returned in func xfrm_dev_state_add().
Fixes: bdfd2d1fa79a ("bonding/xfrm: use real_dev instead of slave_dev") Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If qfq_change_class() is unable to allocate memory for qfq_aggregate,
it frees the class that has been inserted in the class hash table,
but does not unhash it.
Defer the insertion after the problematic allocation.
BUG: KASAN: use-after-free in hlist_add_head include/linux/list.h:884 [inline]
BUG: KASAN: use-after-free in qdisc_class_hash_insert+0x200/0x210 net/sched/sch_api.c:731
Write of size 8 at addr ffff88814a534f10 by task syz-executor.4/31478
The buggy address belongs to the object at ffff88814a534f00
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 16 bytes inside of
128-byte region [ffff88814a534f00, ffff88814a534f80)
The buggy address belongs to the page:
page:ffffea0005294d00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14a534
flags: 0x57ff00000000200(slab|node=1|zone=2|lastcpupid=0x7ff)
raw: 057ff00000000200ffffea00004fee000000000600000006ffff8880110418c0
raw: 0000000000000000000000000010001000000001ffffffff0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x12cc0(GFP_KERNEL|__GFP_NOWARN|__GFP_NORETRY), pid 29797, ts 604817765317, free_ts 604810151744
prep_new_page mm/page_alloc.c:2358 [inline]
get_page_from_freelist+0x1033/0x2b60 mm/page_alloc.c:3994
__alloc_pages+0x1b2/0x500 mm/page_alloc.c:5200
alloc_pages+0x18c/0x2a0 mm/mempolicy.c:2272
alloc_slab_page mm/slub.c:1646 [inline]
allocate_slab+0x2c5/0x4c0 mm/slub.c:1786
new_slab mm/slub.c:1849 [inline]
new_slab_objects mm/slub.c:2595 [inline]
___slab_alloc+0x4a1/0x810 mm/slub.c:2758
__slab_alloc.constprop.0+0xa7/0xf0 mm/slub.c:2798
slab_alloc_node mm/slub.c:2880 [inline]
slab_alloc mm/slub.c:2922 [inline]
__kmalloc+0x315/0x330 mm/slub.c:4050
kmalloc include/linux/slab.h:561 [inline]
kzalloc include/linux/slab.h:686 [inline]
__register_sysctl_table+0x112/0x1090 fs/proc/proc_sysctl.c:1318
mpls_dev_sysctl_register+0x1b7/0x2d0 net/mpls/af_mpls.c:1421
mpls_add_dev net/mpls/af_mpls.c:1472 [inline]
mpls_dev_notify+0x214/0x8b0 net/mpls/af_mpls.c:1588
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:2121
call_netdevice_notifiers_extack net/core/dev.c:2133 [inline]
call_netdevice_notifiers net/core/dev.c:2147 [inline]
register_netdevice+0x106b/0x1500 net/core/dev.c:10312
veth_newlink+0x585/0xac0 drivers/net/veth.c:1547
__rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3452
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3500
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1298 [inline]
free_pcp_prepare+0x223/0x300 mm/page_alloc.c:1342
free_unref_page_prepare mm/page_alloc.c:3250 [inline]
free_unref_page+0x12/0x1d0 mm/page_alloc.c:3298
__vunmap+0x783/0xb60 mm/vmalloc.c:2566
free_work+0x58/0x70 mm/vmalloc.c:80
process_one_work+0x98d/0x1600 kernel/workqueue.c:2276
worker_thread+0x64c/0x1120 kernel/workqueue.c:2422
kthread+0x3b1/0x4a0 kernel/kthread.c:313
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294
Memory state around the buggy address: ffff88814a534e00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88814a534e80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88814a534f00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88814a534f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88814a535000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes: 462dbc9101acd ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
8021q module adds vlan 0 to all interfaces when it starts.
When 8021q module is loaded it isn't possible to create bond
with mv88e6xxx interfaces, bonding module dipslay error
"Couldn't add bond vlan ids", because it tries to add vlan 0
to slave interfaces.
There is unexpected behavior in the switch. When a PVID
is assigned to a port the switch changes VID to PVID
in ingress frames with VID 0 on the port. Expected
that the switch doesn't assign PVID to tagged frames
with VID 0. But there isn't a way to change this behavior
in the switch.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support") Signed-off-by: Eldar Gasanov <eldargasanov2@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VLAN transfer logic should actually check for
FLOW_DISSECTOR_KEY_BASIC, not FLOW_DISSECTOR_KEY_CONTROL. Moreover, do
not fallback to case 2) .n_proto is set to 802.1q or 802.1ad, if
FLOW_DISSECTOR_KEY_BASIC is unset.
Fixes: 783003f3bb8a ("netfilter: nftables_offload: special ethertype handling for VLAN") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We got multiple reports that multi_chunk_sendfile test
case from tls selftest fails. This was sort of expected,
as the original fix was never applied (see it in the first
Link:). The test in question uses sendfile() with count
larger than the size of the underlying file. This will
make splice set MSG_MORE on all sendpage calls, meaning
TLS will never close and flush the last partial record.
Eric seem to have addressed a similar problem in
commit 35f9c09fe9c7 ("tcp: tcp_sendpages() should call tcp_push() once")
by introducing MSG_SENDPAGE_NOTLAST. Unlike MSG_MORE
MSG_SENDPAGE_NOTLAST is not set on the last call
of a "pipefull" of data (PIPE_DEF_BUFFERS == 16,
so every 16 pages or whenever we run out of data).
Having a break every 16 pages should be fine, TLS
can pack exactly 4 pages into a record, so for
aligned reads there should be no difference,
unaligned may see one extra record per sendpage().
Sticking to TCP semantics seems preferable to modifying
splice, but we can revisit it if real life scenarios
show a regression.
Reported-by: Vadim Fedorenko <vfedorenko@novek.ru> Reported-by: Seth Forshee <seth.forshee@canonical.com> Link: https://lore.kernel.org/netdev/1591392508-14592-1-git-send-email-pooja.trivedi@stackpath.com/ Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ChaCha support did not adjust the bidirectional test.
We need to set up KTLS in reverse direction correctly,
otherwise these two cases will fail:
tls.12_chacha.bidir
tls.13_chacha.bidir
Fixes: 4f336e88a870 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A bunch of tests uses uninitialized stack memory as random
data to send. This is harmless but generates compiler warnings.
Explicitly init the buffers with random data.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The spin_trylock() was assumed to contain the implicit
barrier needed to ensure the correct ordering between
STATE_MISSED setting/clearing and STATE_MISSED checking
in commit a90c57f2cedd ("net: sched: fix packet stuck
problem for lockless qdisc").
But it turns out that spin_trylock() only has load-acquire
semantic, for strongly-ordered system(like x86), the compiler
barrier implicitly contained in spin_trylock() seems enough
to ensure the correct ordering. But for weakly-orderly system
(like arm64), the store-release semantic is needed to ensure
the correct ordering as clear_bit() and test_bit() is store
operation, see queued_spin_lock().
So add the explicit barrier to ensure the correct ordering
for the above case.
Fixes: a90c57f2cedd ("net: sched: fix packet stuck problem for lockless qdisc") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Non-ND strict packets with a source LLA go through the packet taps
again, while non-ND strict packets with other source addresses do not,
and we can see a clone of those packets on the vrf interface (we should
not). This is due to a series of changes:
Commit 6f12fa775530[1] made non-ND strict packets not being pushed again
in the packet taps. This changed with commit 205704c618af[2] for those
packets having a source LLA, as they need a lookup with the orig_iif.
The issue now is those packets do not skip the 'vrf_ip6_rcv' function to
the end (as the ones without a source LLA) and go through the check to
call packet taps again. This check was changed by commit 6f12fa775530[1]
and do not exclude non-strict packets anymore. Packets matching
'need_strict && !is_ndisc && is_ll_src' are now being sent through the
packet taps again. This can be seen by dumping packets on the vrf
interface.
Fix this by having the same code path for all non-ND strict packets and
selectively lookup with the orig_iif for those with a source LLA. This
has the effect to revert to the pre-205704c618af[2] condition, which
should also be easier to maintain.
[1] 6f12fa775530 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
[2] 205704c618af ("vrf: packets with lladdr src needs dst at input with orig_iif when needs strict")
Fixes: 205704c618af ("vrf: packets with lladdr src needs dst at input with orig_iif when needs strict") Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Reported-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As documented at drivers/base/platform.c for platform_get_irq:
* Gets an IRQ for a platform device and prints an error message if finding the
* IRQ fails. Device drivers should check the return value for errors so as to
* not pass a negative integer value to the request_irq() APIs.
So, the driver should check that platform_get_irq() return value
is _negative_, not that it's equal to zero, because -ENXIO (return
value from request_irq() if irq was not found) will
pass this check and it leads to passing negative irq to request_irq()
Fixes: 0dd077093636 ("NET: Add ezchip ethernet driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after netif_napi_del()
call.
Fixes: 0dd077093636 ("NET: Add ezchip ethernet driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
greth is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing greth
pointer. So, fix it by moving free_netdev() after of_iounmap()
call.
Fixes: d4c41139df6e ("net: Add Aeroflex Gaisler 10/100/1G Ethernet MAC driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FCS error packets are filtered by default and won't be reported to
driver, so that RX fcs error and PER in testmode always show zero.
Fix this issue by reading fcs error count from hw counter.
We did't fix this issue by disabling fcs error rx filter since it may
let HW suffer some SER errors.
OMAC idx have to be same with BSS idx according to firmware usage.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops") Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: YN Chen <yn.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently in the switch statement case where type is
NL80211_IFTYPE_STATION there is a check to see if type
is not NL80211_IFTYPE_STATION. This check is always false
and is redundant dead code that can be removed.
Addresses-Coverity: ("Logically dead code") Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible the RCPI from the certain antenna is an invalid value,
especially packets are receiving while the system is frequently entering
deep sleep mode, so consider calculating RSSI with the reasonable upper
bound to avoid report the wrong value to the mac80211 layer.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support") Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix theoretical NULL pointer dereference in mt7615_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines. This issue has been identified
by code analysis.
Fixes: 6aa4ed7927f11 ("mt76: mt7615: implement DMA support for MT7622") Fixes: 4bb586bc33b98 ("mt76: mt7663u: sync probe sampling with rate configuration") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even if this is not a real issue since mt76_tx is never run with wcid set
to NULL, fix a theoretical NULL pointer dereference in mt76_tx routine
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0571a753cb07 cancelled delayed work too late, keeping small
race. Cancel work sooner to close it completely.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Fixes: 0571a753cb07 ("net: pxa168_eth: Fix a potential data race in pxa168_eth_remove") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
If bpf_map_update_elem() failed, main() should return a negative error.
Fixes: 832622e6bd18 ("xdp: sample program for new bpf_redirect helper") Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20210616042534.315097-1-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently rtrs when create_qp use a coarse numbers (bigger in general),
which leads to hardware create more resources which only waste memory with
no benefits.
For max_send_wr, we don't really need alway max_qp_wr size when creating
qp, reduce it to cq_size.
For max_recv_wr, cq_size is enough.
With the patch when sess_queue_depth=128, per session (2 paths) memory
consumption reduced from 188 MB to 65MB
When always_invalidate is enabled, we need send more wr, so treat it
special.
Fixes: 9cb837480424e ("RDMA/rtrs: server: main functionality") Link: https://lore.kernel.org/r/20210614090337.29557-2-jinpu.wang@ionos.com Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com> Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vmlinux ".BTF_ids" ELF section is declared in btf_ids.h to hold a list
of zero-filled BTF IDs, which is then patched at link-time with correct
values by resolv_btfids. The section is flagged as "allocable" to preclude
compression, but notably the section contents (BTF IDs) are untyped.
When patching the BTF IDs, resolve_btfids writes in host-native endianness
and relies on libelf for any required translation on reading and updating
vmlinux. However, since the type of the .BTF_ids section content defaults
to ELF_T_BYTE (i.e. unsigned char), no translation occurs. This results in
incorrect patched values when cross-compiling to non-native endianness,
and can manifest as kernel Oops and test failures which are difficult to
troubleshoot [1].
Explicitly set the type of patched data to ELF_T_WORD, the architecture-
neutral ELF type corresponding to the u32 BTF IDs. This enables libelf to
transparently perform any needed endian conversions.
Fix broken Tx ring validation for AF_XDP. The commit under the Fixes
tag, fixed an off-by-one error in the validation but introduced
another error. Descriptors are now let through even if they straddle a
chunk boundary which they are not allowed to do in aligned mode. Worse
is that they are let through even if they straddle the end of the umem
itself, tricking the kernel to read data outside the allowed umem
region which might or might not be mapped at all.
Fix this by reintroducing the old code, but subtract the length by one
to fix the off-by-one error that the original patch was
addressing. The test chunk != chunk_end makes sure packets do not
straddle chunk boundraries. Note that packets of zero length are
allowed in the interface, therefore the test if the length is
non-zero.
Fixes: ac31565c2193 ("xsk: Fix for xp_aligned_validate_desc() when len == chunk_size") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Björn Töpel <bjorn@kernel.org> Link: https://lore.kernel.org/bpf/20210618075805.14412-1-magnus.karlsson@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a missing validation of a Tx descriptor when executing in skb mode
and the umem is in unaligned mode. A descriptor could point to a
buffer straddling the end of the umem, thus effectively tricking the
kernel to read outside the allowed umem region. This could lead to a
kernel crash if that part of memory is not mapped.
In zero-copy mode, the descriptor validation code rejects such
descriptors by checking a bit in the DMA address that tells us if the
next page is physically contiguous or not. For the last page in the
umem, this bit is not set, therefore any descriptor pointing to a
packet straddling this last page boundary will be rejected. However,
the skb path does not use this bit since it copies out data and can do
so to two different pages. (It also does not have the array of DMA
address, so it cannot even store this bit.) The code just returned
that the packet is always physically contiguous. But this is
unfortunately also returned for the last page in the umem, which means
that packets that cross the end of the umem are being allowed, which
they should not be.
Fix this by introducing a check for this in the SKB path only, not
penalizing the zero-copy path.
Fixes: 2b43470add8c ("xsk: Introduce AF_XDP buffer allocation API") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Björn Töpel <bjorn@kernel.org> Link: https://lore.kernel.org/bpf/20210617092255.3487-1-magnus.karlsson@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the rdma_rxe driver attempts to protect atomic responder
resources by taking a reference to the qp which is only freed when the
resource is recycled for a new read or atomic operation. This means that
in normal circumstances there is almost always an extra qp reference once
an atomic operation has been executed which prevents cleaning up the qp
and associated pd and cqs when the qp is destroyed.
This patch removes the call to rxe_add_ref() in send_atomic_ack() and the
call to rxe_drop_ref() in free_rd_atomic_resource(). If the qp is
destroyed while a peer is retrying an atomic op it will cause the
operation to fail which is acceptable.
ipv6_find_hdr() does not validate that this is an IPv6 packet. Add a
sanity check for calling ipv6_find_hdr() to make sure an IPv6 packet
is passed for parsing.
projects / thirdparty / kernel / stable.git / log
