Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Fixes logic that leads to this error when booting mt7621 and other
devices that use the mediatek ethernet driver:
[ 23.144378] mtk_soc_eth 1e100000.ethernet: PPE table busy
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Daniel Golle [Wed, 28 Apr 2021 19:46:46 +0000 (20:46 +0100)]
arm-trusted-firmware-mediatek: fix boot hang on unifi-6-lr
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit f724a583dcf7 updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.
João Henriques [Sun, 18 Apr 2021 22:41:30 +0000 (23:41 +0100)]
dnsmasq: add ignore hosts dir to dnsmasq init script
When running multiple instances of dnsmasq, for example one being for the lan
and another for a guest network, it might not be desirable to have the same dns names
configured in both networks
Hans Dedecker [Sat, 24 Apr 2021 19:03:02 +0000 (21:03 +0200)]
nat46: update to git HEAD
9df230a Zero checksum handling (#25) 7688102 skip generating a UDP4 csum if the UDP6 csum is 0 and zero_csum_pass is set 4a9e4b1 zero csum: avoid calling the checksum adjustment function if udp csum is zero 2de14c5 add a module argument to skip checksum adjust for UDP if checksum is zero
Tony Ambardar [Mon, 12 Apr 2021 23:46:22 +0000 (16:46 -0700)]
bpftools: fix feature override for masking clang
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.
Fixes: 23be333401f0 ("bpftools: update to 5.10.10") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Daniel Golle [Sat, 24 Apr 2021 11:12:09 +0000 (12:12 +0100)]
image: use portable filename in 'append-image-stage'
The 'append-image-stage' command doesn't work when setting the
EXTRA_IMAGE_NAME option of the ImageBuilder as in that case
DEVICE_IMG_PREFIX is modified and no longer matches the value it had in
buildroot. Choose a filename independent of DEVICE_IMG_PREFIX for
images staged using 'append-image-stage' to fix that.
Daniel Golle [Fri, 23 Apr 2021 22:10:08 +0000 (23:10 +0100)]
mediatek: bpi-r64: fix sdcard.img.gz in ImageBuilder
Generating the sdcard.img.gz file requires the initramfs/recovery
image to be present. Use the newly introduced 'append-image-stage'
build command to fix the ImageBuilder for the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to 'append-image' this new command appends an existing binary.
'append-image-stage' also makes a copy of that binary and keeps it in
$(STAGING_DIR_IMAGE). When called from within the ImageBuilder, this
copy is used instead of expecting the binary to be present.
This is useful for artifacts which include the initramfs/recovery image
which is usually not included in the ImageBuilder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 23 Apr 2021 22:12:09 +0000 (23:12 +0100)]
mediatek: mt7622: build AHCI driver as module
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tony Ambardar [Sun, 18 Apr 2021 10:09:44 +0000 (03:09 -0700)]
iproute2: avoid unneeded compiles to speed building
Skip building Makefile targets that aren't packaged: tipc, dcb, ifstat,
rtacct, lnstat, and man. Also, only compile targets needed for the current
build variant i.e. don't compile 'tc' when building an 'ip' variant and
vice versa.
These changes reduce typical build times by over 30%:
$ make package/iproute2/clean && time make -j8 package/iproute2/compile
(old)
...
real 2m24.985s
user 3m12.537s
sys 0m26.677s
(new)
...
real 1m36.945s
user 2m8.734s
sys 0m20.046s
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Make sure all compression algorithms are enabled, for the time being, in order
not to break sysupgrade. In the future, we'd like to disable all except zstd, as
it's the best all-around performer.
Compared to both lzo and zlib, zstd is the best all-around performer. Backport
a kernel patch [1] (to both 5.4 and 5.10), in order to set it as default for
ubifs, if available.
David Bauer [Sat, 17 Apr 2021 18:32:57 +0000 (20:32 +0200)]
rockchip: use alternative CID path
Use an alternative path to access the CID of the SD card in MMC0, used
for the generation of MAC addresses. With Kernel 5.10, the device name
of the MMC controller changed, breaking MAC address generation.
The new path is compatible with Kernel 5.4 as well as Kernel 5.10.
Zheng Bao [Tue, 13 Apr 2021 04:46:17 +0000 (12:46 +0800)]
x86/64: Add support for AMD SOC Ethernet controller
This feature is already supported in kernel. Add definition
and configuration in Makefile of OpenWRT.
It is tested on board Dibbler with processor V1605B.
Dmesg is as below.
--------------------------------------------
[ 0.317122] smpboot: CPU0: AMD Ryzen Embedded V1605B with Radeon
Vega Gfx (family: 0x17, model: 0x11, stepping: 0x0)
[ 8.227270] libphy: amd-xgbe-mii: probed
[ 8.228189] amd-xgbe 0000:02:00.1 eth0: net device enabled
[ 8.228999] libphy: amd-xgbe-mii: probed
[ 8.229921] amd-xgbe 0000:02:00.2 eth1: net device enabled
.....
[ 11.760869] br-lan: port 1(eth0) entered blocking state
[ 11.761365] br-lan: port 1(eth0) entered disabled state
[ 11.762019] device eth0 entered promiscuous mode
[ 11.785285] 8021q: adding VLAN 0 to HW filter on device eth1
[ 16.881431] amd-xgbe 0000:02:00.1 eth0: Link is Up - 1Gbps/Full -
flow control off
[ 16.882108] br-lan: port 1(eth0) entered blocking state
[ 16.882583] br-lan: port 1(eth0) entered forwarding state
[ 16.883249] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
-----------------------------------------------
This updates the NAND driver for MikroTik RB4XX series to work with
kernel 5.10, similarly to the ar934x-nand driver (fb64e2c3).
Support for kernel 5.10 was added to all ath79 subtargets except for the
mikrotik one by commit d6b785d, since patch 920-mikrotik-rb4xx.patch
needed to be reworked. Later, commit f8512661 enabled kernel 5.10 for
the mikrotik subtarget with the nand-rb4xx driver still pending, which
is updated and added back by this patch.
Compile-tested only.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Sven Eckelmann [Thu, 25 Mar 2021 12:26:15 +0000 (13:26 +0100)]
mvebu: Fix sysupgrade for GL.iNet GL-MV1000
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org>
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
For some reason, one of the configure checks results in some infinite
loop and ends up spawning endless gcc processes, causing OOM. Just pass
a configure var to avoid it.
ltq-vdsl-app: extent dsl metrics with state_num and power_state_num
With the old ubus dsl API, the numbers for the individual line_states and
power_states were also returned. These were not ported to the new DSL
C-API. This commit adds the missing information.
For this the internal values are mapped to numbers.
* additional JSON output for state_num:
"state_num": <map_state_number>
Since not all values are meaningful only the following values are
implemented, this can be extended if the future.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
v6:
Add state LSTATE_MAP_NOT_INITILIZED at the beginning of the list
Start the list LSTATE_MAP with -1 Reviewed-by: Andre Heider <a.heider@gmail.com>
This makes no sense on anything but the IXP4xx platform
that we do not even support anymore. If we bring it back,
it can be selectively enabled for that platform only.
We do not enable GPIO_CDEV so do not enable CDEV_V1
either. As we rebuild the whole userspace and kernel
in OpenWRT it doesn't make any sense to support the
old ABI anyway: the new one should be used by default.
The non-MQ CFQ, deadline and noop IO schedulers are
deleted from the Linux kernel
since commit f382fb0bcef4c37dc049e9f6963e3baf204d815c
"block: remove legacy IO schedulers".
Leon M. George [Tue, 23 Mar 2021 10:02:36 +0000 (11:02 +0100)]
odhcp6c: read user scripts from directory
Placeholder DHCP user scripts were added recently.
These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.
References: b4f3d93b5 odhcp6c: add a odhcp6c.user placeholder script
Signed-off-by: Leon M. George <leon@georgemail.eu> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Leon M. George [Tue, 23 Mar 2021 10:02:36 +0000 (11:02 +0100)]
netifd: read udhcpc user scripts from directory
Placeholder DHCP user scripts were added recently.
These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.
References: 130118f7a netifd: add a udhcpc.user placeholder script
Signed-off-by: Leon M. George <leon@georgemail.eu> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
David Bauer [Fri, 16 Apr 2021 16:29:58 +0000 (18:29 +0200)]
ath79: remove unused patch
This patch ist not required, as it only has an effect in case the GPIO
descriptors supplied to num-cs are valid.
As this is not the case for ath79, this patch can safely be omitted. The
issue it tried to fix is actually fixed with
0054-spi-sync-up-initial-chipselect-state.
David Bauer [Fri, 16 Apr 2021 10:30:43 +0000 (12:30 +0200)]
mediatek: fix Ubiquiti UniFi 6 LR LED
When adding Kernel 5.10 support, the kernel configuration did not
include the LED driver required for the UniFi 6 LR. Also the actual
driver source went missing.
Fixes commit c46ccb69d17e ("mediatek: mt7622: add Linux 5.10 support")
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
David Bauer [Wed, 14 Apr 2021 22:54:49 +0000 (00:54 +0200)]
ath79: fix link mode support list on UniFi AC
This fixes incorrect supported link modes indicated when using ethtool
on the Ubiquiti UniFi AC lite / LR / Mesh.
eroot@OpenWrt:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
The reason for this is, that since kernel 5.4 the PHY capabilities are
read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong
state, the capabilities of the SGMII side of the PHY are read.
As a side effect, 10 Mbit/s link modes did not work on these boards.
DENG Qingfang [Sat, 3 Apr 2021 14:59:15 +0000 (22:59 +0800)]
ramips: mt7530 swconfig: fix race condition in register access
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
Ilya Lipnitskiy [Fri, 19 Mar 2021 05:22:52 +0000 (22:22 -0700)]
ramips: drop obsolete arcs_cmdline override patch
CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets
already, which will ensure that the value of 'bootargs' will take
precedence over whatever is in arcs_cmdline.
firmware-utils: tplink-safeloader: support displaying fw info
Add "-i" option for reading & displaying firmware info. First it lists
in-firmware partitions ("fwup-ptn"). Then it checks for human
understandable partitions and prints data found in each of them.
This new feature is meant for development & debug purposes.
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
The old code didn't make sense as it was using "len" variable which was
guaranteed to be always 0. Loop right above broken code is:
while (len > 0) { }
With this recent ALIGN macro fix this resulted in subtracting block size
from 0 and calling write_out_padding() with a negative length.
To calculate amount of bytes needed for padding & alignment it should be
enough to use % 4.
Fixes: a2f66229450d ("firmware-utils: fix few random warnings") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Petr Štetiar [Fri, 9 Apr 2021 12:52:05 +0000 (14:52 +0200)]
tplink-safeloader: fix C7v5 factory flashing from vendor fw > v1.1.x
Currently it's not possible to flash factory images on devices shipped
with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published
2020-12-22):
David Bauer [Wed, 31 Mar 2021 23:20:45 +0000 (01:20 +0200)]
ath79: force SGMII SerDes mode to MAC operation
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de> Tested-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
Mathias Kresin [Sun, 27 Dec 2020 09:28:08 +0000 (10:28 +0100)]
lantiq: add Linux 5.10 support as testing kernel
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Mathias Kresin [Mon, 28 Dec 2020 13:03:54 +0000 (14:03 +0100)]
lantiq: dts: mark PCI bridges as such
Use the device_type property to mark PCI host bridges as such. With
linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI
memory and the PCI init fails.
Mathias Kresin [Sun, 27 Dec 2020 16:25:25 +0000 (17:25 +0100)]
lantiq: ltq-tapi: add kernel 5.10 compatiblity
Due to SCHED_FIFO being a broken scheduler model, all users of
sched_setscheduler() are converted to sched_set_fifo_low() upstream and
sched_setscheduler() is no longer exported.
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ltq tapi
projects / thirdparty / openwrt.git / log
