When it is to cleanup net namespace, rds_tcp_exit_net() will call
rds_tcp_kill_sock(), if t_sock is NULL, it will not call
rds_conn_destroy(), rds_conn_path_destroy() and rds_tcp_conn_free() to free
connection, and the worker cp_conn_w is not stopped, afterwards the net is freed in
net_drop_ns(); While cp_conn_w rds_connect_worker() will call rds_tcp_conn_path_connect()
and reference 'net' which has already been freed.
In rds_tcp_conn_path_connect(), rds_tcp_set_callbacks() will set t_sock = sock before
sock->ops->connect, but if connect() is failed, it will call
rds_tcp_restore_callbacks() and set t_sock = NULL, if connect is always
failed, rds_connect_worker() will try to reconnect all the time, so
rds_tcp_kill_sock() will never to cancel worker cp_conn_w and free the
connections.
Therefore, the condition !tc->t_sock is not needed if it is going to do
cleanup_net->rds_tcp_exit_net->rds_tcp_kill_sock, because tc->t_sock is always
NULL, and there is on other path to cancel cp_conn_w and free
connection. So this patch is to fix this.
rds_tcp_kill_sock():
...
if (net != c_net || !tc->t_sock)
... Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
==================================================================
BUG: KASAN: use-after-free in inet_create+0xbcc/0xd28
net/ipv4/af_inet.c:340
Read of size 4 at addr ffff8003496a4684 by task kworker/u8:4/3721
Fixes: 467fa15356ac("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipip6 tunnels run iptunnel_pull_header on received skbs. This can
determine the following use-after-free accessing iph pointer since
the packet will be 'uncloned' running pskb_expand_head if it is a
cloned gso skb (e.g if the packet has been sent though a veth device)
Fix it resetting iph pointer after iptunnel_pull_header
Fixes: a09a4c8dd1ec ("tunnels: Remove encapsulation offloads on decap") Tested-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a541 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment") Signed-off-by: Junwei Hu <hujunwei4@huawei.com> Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com> Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, the kernel will automatically load the module of any line
dicipline that is asked for. As this sometimes isn't the safest thing
to do, provide a sysctl to disable this feature.
By default, we set this to 'y' as that is the historical way that Linux
has worked, and we do not want to break working systems. But in the
future, perhaps this can default to 'n' to prevent this functionality.
The n_r3964 line discipline driver was written in a different time, when
SMP machines were rare, and users were trusted to do the right thing.
Since then, the world has moved on but not this code, it has stayed
rooted in the past with its lovely hand-crafted list structures and
loads of "interesting" race conditions all over the place.
After attempting to clean up most of the issues, I just gave up and am
now marking the driver as BROKEN so that hopefully someone who has this
hardware will show up out of the woodwork (I know you are out there!)
and will help with debugging a raft of changes that I had laying around
for the code, but was too afraid to commit as odds are they would break
things.
Many thanks to Jann and Linus for pointing out the initial problems in
this codebase, as well as many reviews of my attempts to fix the issues.
It was a case of whack-a-mole, and as you can see, the mole won.
A recent optimization in Clang (r355672) lowers comparisons of the
return value of memcmp against zero to comparisons of the return value
of bcmp against zero. This helps some platforms that implement bcmp
more efficiently than memcmp. glibc simply aliases bcmp to memcmp, but
an optimized implementation is in the works.
This results in linkage failures for all targets with Clang due to the
undefined symbol. For now, just implement bcmp as a tailcail to memcmp
to unbreak the build. This routine can be further optimized in the
future.
Other ideas discussed:
* A weak alias was discussed, but breaks for architectures that define
their own implementations of memcmp since aliases to declarations are
not permitted (only definitions). Arch-specific memcmp
implementations typically declare memcmp in C headers, but implement
them in assembly.
* -ffreestanding also is used sporadically throughout the kernel.
* -fno-builtin-bcmp doesn't work when doing LTO.
Link: https://bugs.llvm.org/show_bug.cgi?id=41035 Link: https://code.woboq.org/userspace/glibc/string/memcmp.c.html#bcmp Link: https://github.com/llvm/llvm-project/commit/8e16d73346f8091461319a7dfc4ddd18eedcff13 Link: https://github.com/ClangBuiltLinux/linux/issues/416 Link: http://lkml.kernel.org/r/20190313211335.165605-1-ndesaulniers@google.com Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: Adhemerval Zanella <adhemerval.zanella@linaro.org> Suggested-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: James Y Knight <jyknight@google.com> Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Nathan Chancellor <natechancellor@gmail.com> Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GNU linker's -z common-page-size's default value is based on the target
architecture. arch/x86/entry/vdso/Makefile sets it to the architecture
default, which is implicit and redundant. Drop it.
Fixes: 2aae950b21e4 ("x86_64: Add vDSO for x86-64 with gettimeofday/clock_gettime/getcpu") Reported-by: Dmitry Golovin <dima@golovin.in> Reported-by: Bill Wendling <morbo@google.com> Suggested-by: Dmitry Golovin <dima@golovin.in> Suggested-by: Rui Ueyama <ruiu@google.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Fangrui Song <maskray@google.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20181206191231.192355-1-ndesaulniers@google.com Link: https://bugs.llvm.org/show_bug.cgi?id=38774 Link: https://github.com/ClangBuiltLinux/linux/issues/31 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vdso{32,64}.so can fail to link with CC=clang when clang tries to find
a suitable GCC toolchain to link these libraries with.
/usr/bin/ld: arch/x86/entry/vdso/vclock_gettime.o:
access beyond end of merged section (782)
This happens because the host environment leaked into the cross compiler
environment due to the way clang searches for suitable GCC toolchains.
Clang is a retargetable compiler, and each invocation of it must provide
--target=<something> --gcc-toolchain=<something> to allow it to find the
correct binutils for cross compilation. These flags had been added to
KBUILD_CFLAGS, but the vdso code uses CC and not KBUILD_CFLAGS (for various
reasons) which breaks clang's ability to find the correct linker when cross
compiling.
Most of the time this goes unnoticed because the host linker is new enough
to work anyway, or is incompatible and skipped, but this cannot be reliably
assumed.
This change alters the vdso makefile to just use LD directly, which
bypasses clang and thus the searching problem. The makefile will just use
${CROSS_COMPILE}ld instead, which is always what we want. This matches the
method used to link vmlinux.
This drops references to DISABLE_LTO; this option doesn't seem to be set
anywhere, and not knowing what its possible values are, it's not clear how
to convert it from CC to LD flag.
The kernel uses the OUTPUT_FORMAT linker script command in it's linker
scripts. Most of the time, the -m option is passed to the linker with
correct architecture, but sometimes (at least for x86_64) the -m option
contradicts the OUTPUT_FORMAT directive.
Specifically, arch/x86/boot and arch/x86/realmode/rm produce i386 object
files, but are linked with the -m elf_x86_64 linker flag when building
for x86_64.
The GNU linker manpage doesn't explicitly state any tie-breakers between
-m and OUTPUT_FORMAT. But with BFD and Gold linkers, OUTPUT_FORMAT
overrides the emulation value specified with the -m option.
LLVM lld has a different behavior, however. When supplied with
contradicting -m and OUTPUT_FORMAT values it fails with the following
error message:
ld.lld: error: arch/x86/realmode/rm/header.o is incompatible with elf_x86_64
Therefore, just add the correct -m after the incorrect one (it overrides
it), so the linker invocation looks like this:
This is not a functional change for GNU ld, because (although not
explicitly documented) OUTPUT_FORMAT overrides -m EMULATION.
Tested by building x86_64 kernel with GNU gcc/ld toolchain and booting
it in QEMU.
[ bp: massage and clarify text. ]
Suggested-by: Dmitry Golovin <dima@golovin.in> Signed-off-by: George Rimar <grimar@accesssoftek.com> Signed-off-by: Tri Vo <trong@android.com> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Tri Vo <trong@android.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Matz <matz@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: morbo@google.com Cc: ndesaulniers@google.com Cc: ruiu@google.com Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190111201012.71210-1-trong@android.com
[nc: Fix conflicts due to lack of commit 58ab5e0c2c40 ("Kbuild: arch:
look for generated headers in obtree") in this tree] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This causes an issue when trying to build with `make LD=ld.lld` if
ld.lld and the rest of your cross tools aren't in the same directory
(ex. /usr/local/bin) (as is the case for Android's build system), as the
GCC_TOOLCHAIN_DIR then gets set based on `which $(LD)` which will point
where LLVM tools are, not GCC/binutils tools are located.
Instead, select the GCC_TOOLCHAIN_DIR based on another tool provided by
binutils for which LLVM does not provide a substitute for, such as
elfedit.
We used to delay switching to the new credentials until after we had
mapped the executable (and possible elf interpreter). That was kind of
odd to begin with, since the new executable will actually then _run_
with the new creds, but whatever.
The bigger problem was that we also want to make sure that we turn off
prof events and tracing before we start mapping the new executable
state. So while this is a cleanup, it's also a fix for a possible
information leak.
Reported-by: Robert Święcki <robert@swiecki.net> Tested-by: Peter Zijlstra <peterz@infradead.org> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Andy Lutomirski <luto@amacapital.net> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Kees Cook <keescook@chromium.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Federico Manuel Bento <up201407890@fc.up.pt> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We aren't supposed to force a stop+start between every i2c msg
when performing multi message transfers. This should eg. cause
the DDC segment address to be reset back to 0 between writing
the segment address and reading the actual EDID extension block.
To quote the E-DDC spec:
"... this standard requires that the segment pointer be
reset to 00h when a NO ACK or a STOP condition is received."
Since we're going to touch this might as well consult the
I2C_M_STOP flag to determine whether we want to force the stop
or not.
The dma_desc->bytes_transferred counter tracks the number of bytes
moved by the DMA channel. This is then used to calculate the information
passed back in the in the tegra_dma_tx_status callback, which is usually
fine.
When the DMA channel is configured as continous, then the bytes_transferred
counter will increase over time and eventually overflow to become negative
so the residue count will become invalid and the ALSA sound-dma code will
report invalid hardware pointer values to the application. This results in
some users becoming confused about the playout position and putting audio
data in the wrong place.
To fix this issue, always ensure the bytes_transferred field is modulo the
size of the request. We only do this for the case of the cyclic transfer
done ISR as anyone attempting to move 2GiB of DMA data in one transfer
is unlikely.
Note, we don't fix the issue that we should /never/ transfer a negative
number of bytes so we could make those fields unsigned.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Accessing per-CPU variables is done by finding the offset of the
variable in the per-CPU block and adding it to the address of the
respective CPU's block.
Section 3.10.8 of ld.bfd's documentation states:
For expressions involving numbers, relative addresses and absolute
addresses, ld follows these rules to evaluate terms:
Other binary operations, that is, between two relative addresses
not in the same section, or between a relative address and an
absolute address, first convert any non-absolute term to an
absolute address before applying the operator."
Note that LLVM's linker does not adhere to the GNU ld's implementation
and as such requires implicitly-absolute terms to be explicitly marked
as absolute in the linker script. If not, it fails currently with:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:153: at least one side of the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:154: at least one side of the expression must be absolute
Makefile:1040: recipe for target 'vmlinux' failed
This is not a functional change for ld.bfd which converts the term to an
absolute symbol anyways as specified above.
Based on a previous submission by Tri Vo <trong@android.com>.
Reported-by: Dmitry Golovin <dima@golovin.in> Signed-off-by: Rafael Ávila de Espíndola <rafael@espindo.la>
[ Update commit message per Boris' and Michael's suggestions. ] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[ Massage commit message more, fix typos. ] Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Dmitry Golovin <dima@golovin.in> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Cao Jin <caoj.fnst@cn.fujitsu.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tri Vo <trong@android.com> Cc: dima@golovin.in Cc: morbo@google.com Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20181219190145.252035-1-ndesaulniers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Release fw_status, raw_fw_status, and tx_res_if when wl12xx_fetch_firmware
failed instead of meaningless goto out to avoid the following memory leak
reports(Only the last one listed):
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
Fixes: df3a950e4e73 ("regulator: act8865: Add act8600 support") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously when doing format enumeration, it was returning all
formats supported by driver, even if they're not supported by hw.
Add missing check for fmt_ver_flag, so it'll be fixed and only those
supported by hw will be returned. Similar thing is already done
in s5p_jpeg_find_format.
It was found by using v4l2-compliance tool and checking result
of VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS test
and using v4l2-ctl to get list of all supported formats.
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
The warning got introduced by commit 930507c18304 ("arm64: add basic
Kconfig symbols for i.MX8"). Since it got enabled for arm64. The warning
haven't been seen before since size_t was 'unsigned int' when built on
arm32.
../drivers/dma/imx-dma.c: In function ‘imxdma_sg_next’:
../include/linux/kernel.h:846:29: warning: comparison of distinct pointer types lacks a cast
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
^~
../include/linux/kernel.h:860:4: note: in expansion of macro ‘__typecheck’
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~
../include/linux/kernel.h:870:24: note: in expansion of macro ‘__safe_cmp’
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~
../include/linux/kernel.h:879:19: note: in expansion of macro ‘__careful_cmp’
#define min(x, y) __careful_cmp(x, y, <)
^~~~~~~~~~~~~
../drivers/dma/imx-dma.c:288:8: note: in expansion of macro ‘min’
now = min(d->len, sg_dma_len(sg));
^~~
Rework so that we use min_t and pass in the size_t that returns the
minimum of two values, using the specified type.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit '3d035f580699 ("drivers/char/hpet.c: allow user controlled mmap for
user processes")' introduced a new kernel command line parameter hpet_mmap,
that is required to expose the memory map of the HPET registers to
user-space. Unfortunately the kernel command line parameter 'hpet_mmap' is
broken and never takes effect due to missing '=' character in the __setup()
code of hpet_mmap_enable.
Before this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.204152] HPET mmap disabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204192] HPET mmap disabled
After this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.203945] HPET mmap enabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204652] HPET mmap disabled
Fixes: 3d035f580699 ("drivers/char/hpet.c: allow user controlled mmap for user processes") Signed-off-by: Buland Singh <bsingh@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On cases where device tree entries for fuse and clock provider are in
different order, fuse driver needs to defer probing. This leads to
freeing incorrect IO base address as the fuse->base variable gets
overwritten once during first probe invocation. This leads to the
following spew during boot:
The virtio-rng driver uses a completion called have_data to wait for a
virtio read to be fulfilled by the hypervisor. The completion is reset
before placing a buffer on the virtio queue and completed by the virtio
callback once data has been written into the buffer.
Prior to this commit, the driver called init_completion on this
completion both during probe as well as when registering virtio buffers
as part of a hwrng read operation. The second of these init_completion
calls should instead be reinit_completion because the have_data
completion has already been inited by probe. As described in
Documentation/scheduler/completion.txt, "Calling init_completion() twice
on the same completion object is most likely a bug".
This bug was present in the initial implementation of virtio-rng in f7f510ec1957 ("virtio: An entropy device, as suggested by hpa"). Back
then the have_data completion was a single static completion rather than
a member of one of potentially multiple virtrng_info structs as
implemented later by 08e53fbdb85c ("virtio-rng: support multiple
virtio-rng devices"). The original driver incorrectly used
init_completion rather than INIT_COMPLETION to reset have_data during
read.
Tested by running `head -c48 /dev/random | hexdump` within crosvm, the
Chrome OS virtual machine monitor, and confirming that the virtio-rng
driver successfully produces random bytes from the host.
Signed-off-by: David Tolnay <dtolnay@gmail.com> Tested-by: David Tolnay <dtolnay@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We increase the default limit for buffer memory allocation by a factor of
10 to 640K to prevent data loss when using fast serial interfaces.
For example when using RS485 without flow-control at speeds of 1Mbit/s
an upwards we've run into problems such as applications being too slow
to read out this buffer (on embedded devices based on imx53 or imx6).
If you want to write transmitted data to a slow SD card and thus have
realtime requirements, this limit can become a problem.
That shouldn't be the case and 640K buffers fix such problems for us.
This value is a maximum limit for allocation only. It has no effect
on systems that currently run fine. When transmission is slow enough
applications and hardware can keep up and increasing this limit
doesn't change anything.
It only _allows_ to allocate more than 2*64K in cases we currently fail to
allocate memory despite having some.
because the kernel has crashed, and we have no known safe way to deal
with the CPU. So, we place the CPU into an infinite loop which we
expect it to never exit - at least not until the system as a whole is
reset by some method.
In the absence of erratum 754327, this code assembles to:
b .
In other words, an infinite loop. When erratum 754327 is enabled,
this becomes:
1: dmb
b 1b
It has been observed that on some systems (eg, OMAP4) where, if a
crash is triggered, the system tries to kexec into the panic kernel,
but fails after taking the secondary CPU down - placing it into one
of these loops. This causes the system to livelock, and the most
noticable effect is the system stops after issuing:
Loading crashdump kernel...
to the system console.
The tested as working solution I came up with was to add wfe() to
these infinite loops thusly:
while (1) {
cpu_relax();
wfe();
}
which, without 754327 builds to:
1: wfe
b 1b
or with 754327 is enabled:
1: dmb
wfe
b 1b
Adding "wfe" does two things depending on the environment we're running
under:
- where we're running on bare metal, and the processor implements
"wfe", it stops us spinning endlessly in a loop where we're never
going to do any useful work.
- if we're running in a VM, it allows the CPU to be given back to the
hypervisor and rescheduled for other purposes (maybe a different VM)
rather than wasting CPU cycles inside a crashed VM.
However, in light of erratum 794072, Will Deacon wanted to see 10 nops
as well - which is reasonable to cover the case where we have erratum
754327 enabled _and_ we have a processor that doesn't implement the
wfe hint.
when erratum 754327 is enabled. We also get the dmb + 10 nop
sequence elsewhere in the kernel, in terminating loops.
This is reasonable - it means we get the workaround for erratum
794072 when erratum 754327 is enabled, but still relinquish the dead
processor - either by placing it in a lower power mode when wfe is
implemented as such or by returning it to the hypervisior, or in the
case where wfe is a no-op, we use the workaround specified in erratum
794072 to avoid the problem.
These as two entirely orthogonal problems - the 10 nops addresses
erratum 794072, and the wfe is an optimisation that makes the system
more efficient when crashed either in terms of power consumption or
by allowing the host/other VMs to make use of the CPU.
I don't see any reason not to use kexec() inside a VM - it has the
potential to provide automated recovery from a failure of the VMs
kernel with the opportunity for saving a crashdump of the failure.
A panic() with a reboot timeout won't do that, and reading the
libvirt documentation, setting on_reboot to "preserve" won't either
(the documentation states "The preserve action for an on_reboot event
is treated as a destroy".) Surely it has to be a good thing to
avoiding having CPUs spinning inside a VM that is doing no useful
work.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported-and-tested-by: Michael <ZeroBeat@gmx.de> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The only sensible explanation is that cdrom_sysctl_register() is called
twice, once from the module init function and once from register_cdrom().
cdrom_sysctl_register() is not mutex protected and may happily execute
twice if the second call is made before the first call is complete.
Use a static atomic to ensure that the function is executed exactly once.
There is no clipping on the x or y axis for logos larger that the framebuffer
size. Therefore: a logo bigger than screen size leads to invalid memory access:
Currently sysfs_strtoul_clamp() is defined as,
82 #define sysfs_strtoul_clamp(file, var, min, max) \
83 do { \
84 if (attr == &sysfs_ ## file) \
85 return strtoul_safe_clamp(buf, var, min, max) \
86 ?: (ssize_t) size; \
87 } while (0)
The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.
To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.
Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value 4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.
This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.
This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.
[ NOTE: this change is required now for following the recent PCM core
change to get rid of snd_pcm_suspend() call. Since DPCM BE takes
the runtime carried from FE while keeping NULL ops, it can hit this
bug. See details at:
https://github.com/thesofproject/linux/pull/582
-- tiwai ]
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287 Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
I've stumbled upon a kernel crash and the logs
pointed me towards the lp5562 driver:
> <4>[306013.841294] lp5562 0-0030: Direct firmware load for lp5562 failed with error -2
> <4>[306013.894990] lp5562 0-0030: Falling back to user helper
> ...
> <3>[306073.924886] lp5562 0-0030: firmware request failed
> <1>[306073.939456] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> <4>[306074.251011] PC is at _raw_spin_lock+0x1c/0x58
> <4>[306074.255539] LR is at release_firmware+0x6c/0x138
> ...
After taking a look I noticed firmware_release()
could be called with either NULL or a dangling
pointer.
Fixes: 10c06d178df11 ("leds-lp55xx: support firmware interface") Signed-off-by: Michal Kazior <michal@plume.com> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
reveals the character arrays prev_comm and next_comm are per
default unsigned char and have values in the range of 0..255.
On x86 both fields are signed as this output shows:
[root@f29]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format
name: sched_switch
ID: 287
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
...
field:char prev_comm[16]; offset:8; size:16; signed:1;
...
field:char next_comm[16]; offset:40; size:16; signed:1;
and the character arrays prev_comm and next_comm are per default signed
char and have values in the range of -1..127. The implementation of
type char is architecture specific.
Since the character arrays in both tracepoints sched_switch and
sched_wakeup should contain ascii characters, simply omit the check for
signedness in the test case.
Output before:
[root@m35lp76 perf]# ./perf test -F 14
14: Parse sched tracepoints fields :
--- start ---
sched:sched_switch: "prev_comm" signedness(0) is wrong, should be 1
sched:sched_switch: "next_comm" signedness(0) is wrong, should be 1
sched:sched_wakeup: "comm" signedness(0) is wrong, should be 1
---- end ----
14: Parse sched tracepoints fields : FAILED!
[root@m35lp76 perf]#
Output after:
[root@m35lp76 perf]# ./perf test -Fv 14
14: Parse sched tracepoints fields :
--- start ---
---- end ----
Parse sched tracepoints fields: Ok
[root@m35lp76 perf]#
Fixes: 489338a717a0 ("perf tests evsel-tp-sched: Fix bitwise operator") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Link: http://lkml.kernel.org/r/20190219153639.31267-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Jason Yan <yanaijie@huawei.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.
Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping
in a cache.
Following the RDMA Connection Manager (CM) protocol, it is clear when
an entry has to evicted form the cache. But life is not perfect,
remote peers may die or be rebooted. Hence, it's a timeout to wipe out
a cache entry, when the PF driver assumes the remote peer has gone.
During workloads where a high number of QPs are destroyed concurrently,
excessive amount of CM DREQ retries has been observed
The problem can be demonstrated in a bare-metal environment, where two
nodes have instantiated 8 VFs each. This using dual ported HCAs, so we
have 16 vPorts per physical server.
64 processes are associated with each vPort and creates and destroys
one QP for each of the remote 64 processes. That is, 1024 QPs per
vPort, all in all 16K QPs. The QPs are created/destroyed using the
CM.
When tearing down these 16K QPs, excessive CM DREQ retries (and
duplicates) are observed. With some cat/paste/awk wizardry on the
infiniband_cm sysfs, we observe as sum of the 16 vPorts on one of the
nodes:
Note that the active/passive side is equally distributed between the
two nodes.
Enabling pr_debug in cm.c gives tons of:
[171778.814239] <mlx4_ib> mlx4_ib_multiplex_cm_handler: id{slave:
1,sl_cm_id: 0xd393089f} is NULL!
By increasing the CM_CLEANUP_CACHE_TIMEOUT from 5 to 30 seconds, the
tear-down phase of the application is reduced from approximately 90 to
50 seconds. Retries/duplicates are also significantly reduced:
Increasing the timeout further didn't help, as these duplicates and
retries stems from a too short CMA timeout, which was 20 (~4 seconds)
on the systems. By increasing the CMA timeout to 22 (~17 seconds), the
numbers fell down to about 10 for both of them.
Adjustment of the CMA timeout is not part of this commit.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
[ad inf.]
Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".
Fix by using 0xfd as the maximum timeout.
Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.
Without this change, we get below error during etm probe:
/ # dmesg | grep etm
[ 6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[ 6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[ 6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[ 6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[ 6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[ 6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[ 6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[ 6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.
It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.
In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.
Fix this by checking if truncated_bytes is lower than PAGE_SIZE.
This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.
I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
Signed-off-by: Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When compiling with -Wformat, clang emits the following warnings:
fs/cifs/smb1ops.c:312:20: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
tgt_total_cnt, total_in_tgt);
^~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:16: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:19: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Louis Taylor <louis@kragniz.eu> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(Taken from https://bugzilla.kernel.org/show_bug.cgi?id=200647)
'get_unused_fd_flags' in kthread cause kernel crash. It works fine on
4.1, but causes crash after get 64 fds. It also cause crash on
ubuntu1404/1604/1804, centos7.5, and the crash messages are almost the
same.
This issue exists since CentOS 7.5 3.10.0-862 and CentOS 7.4
(3.10.0-693.21.1 ) is ok. Root cause: the item 'resize_wait' is not
initialized before being used.
Reported-by: Richard Zhang <zhang.zijian@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the process of creating a node, it will cause NULL pointer
dereference in kernel if o2cb_ctl failed in the interval (mkdir,
o2cb_set_node_attribute(node_num)] in function o2cb_add_node.
The node num is initialized to 0 in function o2nm_node_group_make_item,
o2nm_node_group_drop_item will mistake the node number 0 for a valid
node number when we delete the node before the node number is set
correctly. If the local node number of the current host happens to be
0, cluster->cl_local_node will be set to O2NM_INVALID_NODE_NUM while
o2hb_thread still running. The panic stack is generated as follows:
Kmemleak does not track the array cache (alc->ac) but the alien cache
(alc) instead, so let it track the latter by lifting kmemleak_no_scan()
out of init_arraycache().
There is another place that calls init_arraycache(), but
alloc_kmem_cache_cpus() uses the percpu allocation where will never be
considered as a leak.
After offlining a memory block, kmemleak scan will trigger a crash, as
it encounters a page ext address that has already been freed during
memory offlining. At the beginning in alloc_page_ext(), it calls
kmemleak_alloc(), but it does not call kmemleak_free() in
free_page_ext().
Kmemleak is supposed to work with the memblock_{alloc,free} pair and it
ignores the memblock_reserve() as a memblock_alloc() implementation
detail. It is, however, tolerant to memblock_free() being called on
a sub-range or just a different range from a previous memblock_alloc().
So the original patch looks fine to me. FWIW:
Link: http://lkml.kernel.org/r/20190227144631.16708-1-peng.fan@nxp.com Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes: 322cf7e3a4e8 ("enic: assign affinity hint to interrupts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
/proc/sys/fs/file-max will overflow and be set to 0. That quickly
crashes the system.
This commit sets the max and min value for file-max. The max value is
set to long int. Any higher value cannot currently be used as the
percpu counters are long ints and not unsigned integers.
Note that the file-max value is ultimately parsed via
__do_proc_doulongvec_minmax(). This function does not report error when
min or max are exceeded. Which means if a value largen that long int is
written userspace will not receive an error instead the old value will be
kept. There is an argument to be made that this should be changed and
__do_proc_doulongvec_minmax() should return an error when a dedicated min
or max value are exceeded. However this has the potential to break
userspace so let's defer this to an RFC patch.
Link: http://lkml.kernel.org/r/20190107222700.15954-3-christian@brauner.io Signed-off-by: Christian Brauner <christian@brauner.io> Acked-by: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Waiman Long <longman@redhat.com>
[christian@brauner.io: v4] Link: http://lkml.kernel.org/r/20190210203943.8227-3-christian@brauner.io Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch] Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org Reported-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It believe it is a bad idea to hardcode a specific compiler prefix
that may or may not be installed on a user's system. It is annoying
when testing features that should not require compilers at all.
For example, mrproper, headers_install, etc. should work without
any compiler.
They look like follows on my machine.
$ make ARCH=h8300 mrproper
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
make: h8300-unknown-linux-gcc: Command not found
[ a bunch of the same error messages continue ]
$ make ARCH=h8300 headers_install
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
HOSTCC scripts/basic/fixdep
make: h8300-unknown-linux-gcc: Command not found
WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h
[ snip ]
The solution is to delete this line, or to use cc-cross-prefix like
some architectures do. I chose the latter as a moderate fixup.
I added an alternative 'h8300-linux-' because it is available at:
Notice how we don't call locks_lock_file_wait() which does the
generic VFS lock/unlock/wait work on the inode if rc != 0.
If we are closing the handle, the SMB server is supposed to remove any
locks associated with it. Similarly, cifs.ko frees and wakes up any
lock and lock waiter when closing the file:
cifs_close()
cifsFileInfo_put(file->private_data)
/*
* Delete any outstanding lock records. We'll lose them when the file
* is closed anyway.
*/
down_write(&cifsi->lock_sem);
list_for_each_entry_safe(li, tmp, &cifs_file->llist->locks, llist) {
list_del(&li->llist);
cifs_del_lock_waiters(li);
kfree(li);
}
list_del(&cifs_file->llist->llist);
kfree(cifs_file->llist);
up_write(&cifsi->lock_sem);
So we can safely ignore unlocking failures in cifs_lock() if they
happen with the FL_CLOSE flag hint set as both the server and the
client take care of it during the actual closing.
This is not a proper fix for the unlocking failure but it's safe and
it seems to prevent the lock leakages and crashes the customer
experiences.
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Steve French <stfrench@microsoft.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When releasing socket, it is possible to enter hci_sock_release() and
hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread.
The reference count of hdev should be decremented only once from one of
them but if storing hdev to local variable in hci_sock_release() before
detached from socket and setting to NULL in hci_sock_dev_event(),
hci_dev_put(hdev) is unexpectedly called twice. This is resolved by
referencing hdev from socket after bt_sock_unlink() in
hci_sock_release().
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.
It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.
This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.
When MPOL_MF_STRICT was specified and an existing page was already on a
node that does not follow the policy, mbind() should return -EIO. But
commit 6f4576e3687b ("mempolicy: apply page table walker on
queue_pages_range()") broke the rule.
And commit c8633798497c ("mm: mempolicy: mbind and migrate_pages support
thp migration") didn't return the correct value for THP mbind() too.
If MPOL_MF_STRICT is set, ignore vma_migratable() to make sure it
reaches queue_pages_to_pte_range() or queue_pages_pmd() to check if an
existing page was already on a node that does not follow the policy.
And, non-migratable vma may be used, return -EIO too if MPOL_MF_MOVE or
MPOL_MF_MOVE_ALL was specified.
Tested with https://github.com/metan-ucw/ltp/blob/master/testcases/kernel/syscalls/mbind/mbind02.c
[akpm@linux-foundation.org: tweak code comment] Link: http://lkml.kernel.org/r/1553020556-38583-1-git-send-email-yang.shi@linux.alibaba.com Fixes: 6f4576e3687b ("mempolicy: apply page table walker on queue_pages_range()") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by: Oscar Salvador <osalvador@suse.de> Reported-by: Cyril Hrubis <chrubis@suse.cz> Suggested-by: Kirill A. Shutemov <kirill@shutemov.name> Acked-by: Rafael Aquini <aquini@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m = 1UL << (BITS_PER_LONG - 2);
while (m > x)
m >>= 2;
Which is a linear search for the highest even bit smaller or equal to @x
We can implement this using a binary search using __fls() (or better when
its hardware implemented).
m = 1UL << (__fls(x) & ~1UL);
Especially for small values of @x; which are the more common arguments
when doing a CDF on idle times; the linear search is near to worst case,
while the binary search of __fls() is a constant 6 (or 5 on 32bit)
branches.
Averages computed over all values <128k using a LFSR to generate order.
Cold numbers have a LFSR based branch trace buffer 'confuser' ran between
each int_sqrt() invocation.
Link: http://lkml.kernel.org/r/20171020164644.936577234@infradead.org Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Suggested-by: Joe Perches <joe@perches.com> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Anshul Garg <aksgarg1989@gmail.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: David Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Michael Davidson <md@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Jari Ruusu <jari.ruusu@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debug exception handlers may be called for exceptions generated both by
user and kernel code. In many cases, this is checked explicitly, but
in other cases things either happen to work by happy accident or they
go slightly wrong. For example, executing 'brk #4' from userspace will
enter the kprobes code and be ignored, but the instruction will be
retried forever in userspace instead of delivering a SIGTRAP.
Fix this issue in the most stable-friendly fashion by simply adding
explicit checks of the triggering exception level to all of our debug
exception handlers.
Cc: <stable@vger.kernel.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by
taking a hardware watchpoint. Unfortunately, if a debug handler returns
a non-zero value, then we will propagate the UNKNOWN FAR value to
userspace via the si_addr field of the SIGTRAP siginfo_t.
Instead, let's set si_addr to take on the PC of the faulting instruction,
which we have available in the current pt_regs.
Cc: <stable@vger.kernel.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If STM=n, it doesn't make sense to ask about STM_DUMMY and
STM_SOURCE_CONSOLE support, which are not even built when enabled
anyway. Hence hide these options if STM=n.
The coresight drivers have absolutely no control over bind and unbind
operations triggered from sysfs. The operations simply can't be
cancelled or denied event when one or several tracing sessions are
under way. Since the memory associated to individual device is
invariably freed, the end result is a kernel crash when the path from
source to sink is travelled again as demonstrated here[1].
One solution could be to keep track of all the path (i.e tracing
session) that get created and iterate through the elements of those path
looking for the coresight device that is being removed. This proposition
doesn't scale well since there is no upper bound on the amount of
concurrent trace session that can be created.
With the above in mind, this patch prevent devices from being unbounded
from their driver by using the driver->suppress_bind_attr option. That way
trace sessions can be managed without fearing to loose devices.
Since device can't be removed anymore the xyz_remove() functions found in
each driver is also removed.
As is the case for a number of other architectures that have a 32-bit
compat mode, enable KEYS_COMPAT if both COMPAT and KEYS are enabled.
This allows AArch32 programs to use the keyctl() system call when
running on an AArch64 kernel.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API") Cc: <stable@vger.kernel.org> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMT disable 'nosmt' command line argument is not working properly when
CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are
required to be brought up due to the MCE issues, cannot work. The CPUs are
then kept in a half dead state.
As the 'nosmt' functionality has become popular due to the speculative
hardware vulnerabilities, the half torn down state is not a proper solution
to the problem.
Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is
possible.
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.598166056@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A TSC packet can slip past MTC packets so that the timestamp appears to
go backwards. One estimate is that can be up to about 40 CPU cycles,
which is certainly less than 0x1000 TSC ticks, but accept slippage an
order of magnitude more to be on the safe side.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 79b58424b821c ("perf tools: Add Intel PT support for decoding MTC packets") Link: http://lkml.kernel.org/r/20190325135135.18348-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
A new dir entry can be created in get_subdir and its 'header->parent' is
set to NULL. Only after insert_header success, it will be set to 'dir',
otherwise 'header->parent' is set to NULL and drop_sysctl_table is called.
However in err handling path of get_subdir, drop_sysctl_table also be
called on 'new->header' regardless its value of parent pointer. Then
put_links is called, which triggers NULL-ptr deref when access member of
header->parent.
In fact we have multiple error paths which call drop_sysctl_table() there,
upon failure on insert_links() we also call drop_sysctl_table().And even
in the successful case on __register_sysctl_table() we still always call
drop_sysctl_table().This patch fix it.
Link: http://lkml.kernel.org/r/20190314085527.13244-1-yuehaibing@huawei.com Fixes: 0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reported-by: Hulk Robot <hulkci@huawei.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> [3.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com> Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
projects / thirdparty / kernel / stable.git / log
