Clocks are in fact slightly different on MMP3. In particular, PLL2 is
fixed to a different frequency, there's an extra PLL3, and the GPU
clocks are configured differently.
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates] Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag] Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kobject_init_and_add() returns an error in the function
qib_create_port_files(), the function kobject_put() is not called for the
corresponding kobject, which potentially leads to memory leak.
This patch fixes the issue by calling kobject_put() even if
kobject_init_and_add() fails. In addition, the ppd->diagc_kobj is released
along with other kobjects when the sysfs is unregistered.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Link: https://lore.kernel.org/r/20200512031328.189865.48627.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Suggested-by: Lin Yi <teroincn@gmail.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The opaque pointer passed to the IRQ handler is a pointer to the
drm_device, not a pointer to our ingenic_drm structure.
It still worked, because our ingenic_drm structure contains the
drm_device as its first field, so the pointer received had the same
value, but this was not semantically correct.
Fix the assigned-clock-parents to higher frequency clock to avoid h264
encode timeout:
[ 134.763465] mtk_vpu 10020000.vpu: vpu ipi 4 ack time out !
[ 134.769008] [MTK_VCODEC][ERROR][18]: vpu_enc_send_msg() vpu_ipi_send msg_id c002 len 32 fail -5
[ 134.777707] [MTK_VCODEC][ERROR][18]: vpu_enc_encode() AP_IPIMSG_ENC_ENCODE 0 fail
venc_sel is the clock used by h264 encoder, and venclt_sel is the clock
used by vp8 encoder. Assign venc_sel to vcodecpll_ck and venclt_sel to
vcodecpll_370p5.
The commit 7ecced0934e5 ("gpio: exar: add a check for the return value
of ida_simple_get fails") added a goto jump to the common error
handler for ida_simple_get() error, but this is wrong in two ways:
it doesn't set the proper return code and, more badly, it invokes
ida_simple_remove() with a negative index that shall lead to a kernel
panic via BUG_ON().
This patch addresses those two issues.
Fixes: 7ecced0934e5 ("gpio: exar: add a check for the return value of ida_simple_get fails") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tomas Paukrt reports that his SAM9X60 based system (ARM926, ARMv5TJ)
fails to fix up alignment faults, eventually resulting in a kernel
oops.
The problem occurs when using CONFIG_CPU_USE_DOMAINS with commit e6978e4bf181 ("ARM: save and reset the address limit when entering an
exception"). This is because the address limit is set back to
TASK_SIZE on exception entry, and, although it is restored on exception
exit, the domain register is not.
At this point, addr_limit is correctly restored to KERNEL_DS for
__probe_kernel_read() to continue execution, but dacr.kernel is not,
it has been reset by the set_fs(old_fs) to DOMAIN_CLIENT.
This would not have happened prior to the mentioned commit, because
addr_limit would remain KERNEL_DS, so get_fs() would have returned
KERNEL_DS, and so would correctly nest.
This commit fixes the problem by also saving the DACR on exception
entry if either CONFIG_CPU_SW_DOMAIN_PAN or CONFIG_CPU_USE_DOMAINS are
enabled, and resetting the DACR appropriately on exception entry to
match addr_limit and PAN settings.
Fixes: e6978e4bf181 ("ARM: save and reset the address limit when entering an exception") Reported-by: Tomas Paukrt <tomas.paukrt@advantech.cz> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Consolidate the user access assembly code to asm/uaccess-asm.h. This
moves the csdb, check_uaccess, uaccess_mask_range_ptr, uaccess_enable,
uaccess_disable, uaccess_save, uaccess_restore macros, and creates two
new ones for exception entry and exit - uaccess_entry and uaccess_exit.
This makes the uaccess_save and uaccess_restore macros private to
asm/uaccess-asm.h.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a use-after-free noticed by running with KASAN enabled. If
rmi_irq_fn() is run twice in a row, then rmi_f11_attention() (among
others) will end up reading from drvdata->attn_data.data, which was
freed and left dangling in rmi_irq_fn().
Commit 55edde9fff1a ("Input: synaptics-rmi4 - prevent UAF reported by
KASAN") correctly identified and analyzed this bug. However the attempted
fix only NULLed out a local variable, missing the fact that
drvdata->attn_data is a struct, not a pointer.
NULL out the correct pointer in the driver data to prevent the attention
functions from copying from it.
On the Lenovo ThinkPad Twist S230u (3347-4HU) with BIOS version
"GDETC1WW (1.81 ) 06/27/2019", the keyboard, Synaptics TouchPad, and
TrackPoint either do not function or stop functioning a few minutes
after boot. This problem has been noted before, perhaps only occurring
with BIOS 1.57 and later.[1][2][3][4][5]
Odds of a BIOS fix appear to be low: 1.57 was released over 6 years ago
and although the [BIOS changelog] notes "Fixed an issue of UEFI
touchpad/trackpoint/keyboard/touchscreen" in 1.58, it appears to be
insufficient.
Setting i8042.reset=1 or adding 33474HU to the reset list avoids the
issue on my system from either warm or cold boot.
The PWM iomem resource is optional and its presence indicates whether
the GPIO chip has a PWM or not, which is why mvebu_pwm_probe() returned
successfully when the PWM resource was not present. With f51b18d92b66
the driver switched to devm_platform_ioremap_resource_byname() and
its error return is propagated to the caller, so now a missing PWM resource
leads to a probe error in the driver.
To fix this explicitly test for the presence of the PWM resource and
return successfully when it's not there. Do this check before the check
for the clock is done (which GPIO chips without a PWM do not have). Also
move the existing comment why the PWM resource is optional up to the
actual check.
Sending [ 0x05, 0x20, 0x00, 0x0f, 0x06 ] packet for Xbox One S controllers
fixes an issue where controller is stuck in Bluetooth mode and not sending
any inputs.
input_flush_device() should only be called once the struct file is being
released and no open descriptors remain, but evdev_flush() was calling
it whenever a file descriptor was closed.
This caused uploaded force-feedback effects to be erased when a process
did a dup()/close() on the event FD, called system(), etc.
Call input_flush_device() from evdev_release() instead.
Based on available information this uses the singletouch irtouch
protocol. This is tested and confirmed to be fully functional on
the BonXeon TP hardware I have.
This patch fixes the following warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc5-next-20200514-syzkaller #0 Not tainted
-----------------------------
drivers/net/hamradio/bpqether.c:149 RCU-list traversed in non-reader section!!
Since rtnl lock is held, pass this cond in list_for_each_entry_rcu().
Reported-by: syzbot+bb82cafc737c002d11ca@syzkaller.appspotmail.com Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC 10 is very strict about symbol clash, and lwt_len_hist_user contains
a symbol which clashes with libbpf:
/usr/bin/ld: samples/bpf/lwt_len_hist_user.o:(.bss+0x0): multiple definition of `bpf_log_buf'; samples/bpf/bpf_load.o:(.bss+0x8c0): first defined here
collect2: error: ld returned 1 exit status
bpf_log_buf here seems to be a leftover, so removing it.
If raw_copy_from_user(to, from, N) returns K, callers expect
the first N - K bytes starting at to to have been replaced with
the contents of corresponding area starting at from and the last
K bytes of destination *left* *unmodified*.
What arch/sky/lib/usercopy.c is doing is broken - it can lead to e.g.
data corruption on write(2).
raw_copy_to_user() is inaccurate about return value, which is a bug,
but consequences are less drastic than for raw_copy_from_user().
And just what are those access_ok() doing in there? I mean, look into
linux/uaccess.h; that's where we do that check (as well as zero tail
on failure in the callers that need zeroing).
AFAICS, all of that shouldn't be hard to fix; something like a patch
below might make a useful starting point.
I would suggest moving these macros into usercopy.c (they are never
used anywhere else) and possibly expanding them there; if you leave
them alive, please at least rename __copy_user_zeroing(). Again,
it must not zero anything on failed read.
Said that, I'm not sure we won't be better off simply turning
usercopy.c into usercopy.S - all that is left there is a couple of
functions, each consisting only of inline asm.
Guo Ren reply:
Yes, raw_copy_from_user is wrong, it's no need zeroing code.
unsigned long _copy_from_user(void *to, const void __user *from,
unsigned long n)
{
unsigned long res = n;
might_fault();
if (likely(access_ok(from, n))) {
kasan_check_write(to, n);
res = raw_copy_from_user(to, from, n);
}
if (unlikely(res))
memset(to + (n - res), 0, res);
return res;
}
EXPORT_SYMBOL(_copy_from_user);
Hey, I've no idea about the instruction scheduling on csky -
if that doesn't slow the things down, all the better. It's just
that copy_to_user() and friends are on fairly hot codepaths,
and in quite a few situations they will dominate the speed of
e.g. read(2). So I tried to keep the fast path unchanged.
Up to the architecture maintainers, obviously. Which would be
you...
As for the fixups size increase (__ex_table size is unchanged)...
You have each of those macros expanded exactly once.
So the size is not a serious argument, IMO - useless complexity
would be, if it is, in fact, useless; the size... not really,
especially since those extra subi will at least offset it.
Again, up to you - asm optimizations of (essentially)
memcpy()-style loops are tricky and can depend upon the
fairly subtle details of architecture. So even on something
I know reasonably well I would resort to direct experiments
if I can't pass the buck to architecture maintainers.
It *is* worth optimizing - this is where read() from a file
that is already in page cache spends most of the time, etc.
Guo Ren reply:
Thx, after fixup some typo “sub %0, 4”, apply the patch.
TODO:
- user copy/from codes are still need optimizing.
riscv64-none-linux-gnu-ld: mm/page_alloc.o: in function `.L0 ':
page_alloc.c:(.text+0xd34): undefined reference to `__kernel_map_pages'
riscv64-none-linux-gnu-ld: page_alloc.c:(.text+0x104a): undefined reference to `__kernel_map_pages'
riscv64-none-linux-gnu-ld: mm/page_alloc.o: in function `__pageblock_pfn_to_page':
page_alloc.c:(.text+0x145e): undefined reference to `__kernel_map_pages'
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The format of temperature limitation registers are 8-bit 2's complement
and the range is -128~127.
Converts the reading value to signed char to fix the incorrect range
of temperature limitation registers.
pm_resump api did not handle drm_mode_config_helper_resume error.
This change add handle to return drm_mode_config_helper_resume`s
error number. This code logic is aligned with api pm_suspend.
After this change, the code maybe a bit readable.
Interrupt has been disabled in __schedule() with local_irq_disable()
and enabled in finish_task_switch->finish_lock_switch() with
local_irq_enabled(), So needn't to disable irq here.
Right now, trying to use RTC purely with the ti-sysc / clkctrl framework
fails to enable the RTC module properly. Based on experimentation, this
appears to be because RTC is sourced from the clkdiv32k optional clock.
TRM is not very clear on this topic, but fix the RTC to use the proper
source clock nevertheless.
Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Link: https://lkml.kernel.org/r/20200424152301.4018-1-t-kristo@ti.com Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drop static declaration to fix following build error if FRAME_POINTER disabled,
riscv64-linux-ld: arch/riscv/kernel/perf_callchain.o: in function `.L0':
perf_callchain.c:(.text+0x2b8): undefined reference to `walk_stackframe'
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix unmet direct dependencies Warning and fix Kconfig indent.
WARNING: unmet direct dependencies detected for POWER_RESET_SYSCON
Depends on [n]: POWER_RESET [=n] && OF [=y] && HAS_IOMEM [=y]
Selected by [y]:
- SOC_VIRT [=y]
WARNING: unmet direct dependencies detected for POWER_RESET_SYSCON_POWEROFF
Depends on [n]: POWER_RESET [=n] && OF [=y] && HAS_IOMEM [=y]
Selected by [y]:
- SOC_VIRT [=y]
WARNING: unmet direct dependencies detected for RTC_DRV_GOLDFISH
Depends on [n]: RTC_CLASS [=n] && OF [=y] && HAS_IOMEM [=y] && (GOLDFISH [=y] || COMPILE_TEST [=n])
Selected by [y]:
- SOC_VIRT [=y]
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
For MST case: when update_config is called to disable a stream,
this clears the settings for all the streams on that link.
We should only clear the settings for the stream that was disabled.
[How]
Clear the settings after the call to remove display is called.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I ran into a randconfig build failure with CONFIG_FIXED_PHY=m
and CONFIG_GIANFAR=y:
x86_64-linux-ld: drivers/net/ethernet/freescale/gianfar.o:(.rodata+0x418): undefined reference to `fixed_phy_change_carrier'
It seems the same thing can happen with dpaa and ucc_geth, so change
all three to do an explicit 'select FIXED_PHY'.
The fixed-phy driver actually has an alternative stub function that
theoretically allows building network drivers when fixed-phy is
disabled, but I don't see how that would help here, as the drivers
presumably would not work then.
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^ Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A call to 'regulator_get()' is hidden in 'twl6030_usb_ldo_init()'. A
corresponding put must be performed in the error handling path, as
already done in the remove function.
While at it, also move a 'free_irq()' call in the error handling path in
order to be consistent.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential race in fscache operation enqueuing for reading and
copying multiple pages from cachefiles to netfs. The problem can be seen
easily on a heavy loaded system (for example many processes reading files
continually on an NFS share covered by fscache triggered this problem within
a few minutes).
Releasing the AMDGPU BO ref directly leads to problems when BOs were
exported as DMA bufs. Releasing the GEM reference makes sure that the
AMDGPU/TTM BO is not freed too early.
Also take a GEM reference when importing BOs from DMABufs to keep
references to imported BOs balances properly.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Tested-by: Alex Sierra <alex.sierra@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Sierra <alex.sierra@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As this is already properly handled in amdgpu_gfx_off_ctrl(). In fact,
this unnecessary cancel_delayed_work_sync may leave a small time window
for race condition and is dangerous.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch rearranges gfs2_add_revoke so that the extra glock
reference is added earlier on in the function to avoid races in which
the glock is freed before the new reference is taken.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, function gfs2_quota_lock checked if it was called
from a privileged user, and if so, it bypassed the quota check:
superuser can operate outside the quotas.
That's the wrong place for the check because the lock/unlock functions
are separate from the lock_check function, and you can do lock and
unlock without actually checking the quotas.
This patch moves the check to gfs2_quota_lock_check.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Looks like using the UART CTS pin does not always trigger for a wake-up
when the SoC is idle.
This is probably because the modem first uses gpio_149 to signal the SoC
that data will be sent, and the CTS will only get used later when the
data transfer is starting.
Let's fix the issue by configuring the gpio_149 pad as the wakeirq for
UART. We have gpio_149 managed by the USB PHY for powering up the right
USB mode, and after that, the gpio gets recycled as the modem wake-up
pin. If needeed, the USB PHY can also later on be configured to use
gpio_149 pad as the wakeirq as a shared irq.
Let's also configure the missing properties for uart-has-rtscts and
current-speed for the modem port while at it. We already configure the
hardware flow control pins with uart1_pins pinctrl setting.
Cc: maemo-leste@lists.dyne.org Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.
The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.
In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is another TRX40 based motherboard with ALC1220-VB USB-audio
that requires a static mapping table.
This motherboard also has a PCI device which advertises no codecs. The
PCI ID is 1022:1487 and PCI SSID is 1022:d102. As this is using the AMD
vendor ID, don't blacklist for now in case other boards have a working
audio device with the same ssid.
The driver currently leaves GPIO IRQs unmasked even when the GPIO IRQ
client has released the GPIO IRQ. This allows the HW to raise IRQs, and
SW to process them, after shutdown. Fix this by masking the IRQ when it's
shut down. This is usually taken care of by the irqchip core, but since
this driver has a custom irq_shutdown implementation, it must do this
explicitly itself.
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Dts files with Rockchip rk3399 'gpu' nodes were manually verified.
In order to automate this process arm,mali-midgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-midgard.yaml expects interrupts and interrupt-names values
in the same order. Fix this for rk3399.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/gpu/
arm,mali-midgard.yaml
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
After patch f864edff110d ("ASoC: qdsp6: q6routing: remove default routing")
and 9b60441692d9 ("ASoC: qdsp6: q6asm-dai: only enable dais from device tree")
asm dais and routing needs to be properly specified at device tree level.
ocelot_set_ageing_time has 2 callers:
- felix_set_ageing_time: from drivers/net/dsa/ocelot/felix.c
- ocelot_port_attr_ageing_set: from drivers/net/ethernet/mscc/ocelot.c
The issue described in the fixed commit below actually happened for the
felix_set_ageing_time code path only, since ocelot_port_attr_ageing_set
was already dividing by 1000. So to make both paths symmetrical (and to
fix addresses getting aged way too fast on Ocelot), stop dividing by
1000 at caller side altogether.
Fixes: c0d7eccbc761 ("net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of reload fail, the mlxsw_sp->ports contains a pointer to a
freed memory (either by reload_down() or reload_up() error path).
Fix this by initializing the pointer to NULL and checking it before
dereferencing in split/unsplit/type_set callpaths.
Fixes: 24cc68ad6c46 ("mlxsw: core: Add support for reload") Reported-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function devm_platform_ioremap_resource(), if get resource
failed, the return value is ERR_PTR() not NULL. Thus it must be
replaced by IS_ERR(), or else it may result in crashes if a critical
error path is encountered.
Fixes: 0ce5ebd24d25 ("mfd: ioc3: Add driver for SGI IOC3 chip") Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.
Fixes: fe6f700d6cbb ("net/mlx4_core: Respond to operation request by firmware") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".
Fixes: 1f26dac32057 ("[NET]: Add Sun Cassini driver.") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot free record on any transient error because it leads to
losing previos data. Check socket error to know whether record must
be freed or not.
Fixes: d10523d0b3d7 ("net/tls: free the record on encryption error") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bpf_exec_tx_verdict() can return negative value for copied
variable. In that case this value will be pushed back to caller
and the real error code will be lost. Fix it using signed type and
checking for positive value.
Fixes: d10523d0b3d7 ("net/tls: free the record on encryption error") Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When driver is reloading during recovery flow, it can't get new commands
till command interface is up again. Otherwise we may get to null pointer
trying to access non initialized command structures.
Add cmdif state to avoid processing commands while cmdif is not ready.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After driver creates (via FW command) an EQ for commands, the driver will
be informed on new commands completion by EQE. However, due to a race in
driver's internal command mode metadata update, some new commands will
still be miss-handled by driver as if we are in polling mode. Such commands
can get two non forced completion, leading to already freed command entry
access.
CREATE_EQ command, that maps EQ to the command queue must be posted to the
command queue while it is empty and no other command should be posted.
Add SW mechanism that once the CREATE_EQ command is about to be executed,
all other commands will return error without being sent to the FW. Allow
sending other commands only after successfully changing the driver's
internal command mode metadata.
We can safely return error to all other commands while creating the command
EQ, as all other commands might be sent from the user/application during
driver load. Application can rerun them later after driver's load was
finished.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa139 ("r8169: add support for RTL8117") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In "wireguard: queueing: preserve flow hash across packet scrubbing", we
were required to slightly increase the size of the receive replay
counter to something still fairly small, but an increase nonetheless.
It turns out that we can recoup some of the additional memory overhead
by splitting up the prior union type into two distinct types. Before, we
used the same "noise_counter" union for both sending and receiving, with
sending just using a simple atomic64_t, while receiving used the full
replay counter checker. This meant that most of the memory being
allocated for the sending counter was being wasted. Since the old
"noise_counter" type increased in size in the prior commit, now is a
good time to split up that union type into a distinct "noise_replay_
counter" for receiving and a boring atomic64_t for sending, each using
neither more nor less memory than required.
Also, since sometimes the replay counter is accessed without
necessitating additional accesses to the bitmap, we can reduce cache
misses by hoisting the always-necessary lock above the bitmap in the
struct layout. We also change a "noise_replay_counter" stack allocation
to kmalloc in a -DDEBUG selftest so that KASAN doesn't trigger a stack
frame warning.
All and all, removing a bit of abstraction in this commit makes the code
simpler and smaller, in addition to the motivating memory usage
recuperation. For example, passing around raw "noise_symmetric_key"
structs is something that really only makes sense within noise.c, in the
one place where the sending and receiving keys can safely be thought of
as the same type of object; subsequent to that, it's important that we
uniformly access these through keypair->{sending,receiving}, where their
distinct roles are always made explicit. So this patch allows us to draw
that distinction clearly as well.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's important that we clear most header fields during encapsulation and
decapsulation, because the packet is substantially changed, and we don't
want any info leak or logic bug due to an accidental correlation. But,
for encapsulation, it's wrong to clear skb->hash, since it's used by
fq_codel and flow dissection in general. Without it, classification does
not proceed as usual. This change might make it easier to estimate the
number of innerflows by examining clustering of out of order packets,
but this shouldn't open up anything that can't already be inferred
otherwise (e.g. syn packet size inference), and fq_codel can be disabled
anyway.
Furthermore, it might be the case that the hash isn't used or queried at
all until after wireguard transmits the encrypted UDP packet, which
means skb->hash might still be zero at this point, and thus no hash
taken over the inner packet data. In order to address this situation, we
force a calculation of skb->hash before encrypting packet data.
Of course this means that fq_codel might transmit packets slightly more
out of order than usual. Toke did some testing on beefy machines with
high quantities of parallel flows and found that increasing the
reply-attack counter to 8192 takes care of the most pathological cases
pretty well.
Reported-by: Dave Taht <dave.taht@gmail.com> Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@toke.dk> Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior we read the preshared key after dropping the handshake lock, which
isn't an actual crypto issue if it races, but it's still not quite
correct. So copy that part of the state into a temporary like we do with
the rest of the handshake state variables. Then we can release the lock,
operate on the temporary, and zero it out at the end of the function. In
performance tests, the impact of this was entirely unnoticable, probably
because those bytes are coming from the same cacheline as other things
that are being copied out in the same manner.
Reported-by: Matt Dunwoodie <ncon@noconroy.net> Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sq closure when we free its descriptors, we should also update netdev
txq on completions which would not arrive. Otherwise if we reopen sqs
and attach them back, for example on fw fatal recovery flow, we may get
tx timeout.
In the cited commit inner_tirs argument was added to create and destroy
inner tirs, and no indication was added to mlx5e_modify_tirs_hash()
function. In order to have a consistent handling, use
inner_indir_tir[0].tirn in tirs destroy/modify function as an indication
to whether inner tirs are created.
Inner tirs are not created for representors and before this commit,
a call to mlx5e_modify_tirs_hash() was sending HW commands to
modify non-existent inner tirs.
Fixes: 46dc933cee82 ("net/mlx5e: Provide explicit directive if to create inner indirect tirs") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TLS TIS object contains the dek/key ID.
By destroying the key first, the TIS would contain an invalid
non-existing key ID.
Reverse the destroy order, this also acheives the desired assymetry
between the destroy and the create flows.
Fixes: e9c1a793210f ("tipc: add dst_cache support for udp media") Cc: Xin Long <lucien.xin@gmail.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bdf6fa52f01b ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes: bdf6fa52f01b ("sctp: handle association restarts when the socket is closed.") Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the side effect that starts the shutdown timer was processed
multiple times, which can happen as multiple paths can trigger it. This of
course leads to the BUG halt in add_timer getting called.
Fix seems pretty straightforward, just check before the timer is added if its
already been started. If it has mod the timer instead to min(current
expiration, new expiration)
Its been tested but not confirmed to fix the problem, as the issue has only
occured in production environments where test kernels are enjoined from being
installed. It appears to be a sane fix to me though. Also, recentely,
Jere found a reproducer posted on list to confirm that this resolves the
issues
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Vlad Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: jere.leppanen@nokia.com CC: marcelo.leitner@gmail.com CC: netdev@vger.kernel.org Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For nexthop groups, attributes after NHA_GROUP_TYPE are invalid, but
nh_check_attr_group starts checking at NHA_GROUP. The group type defaults
to multipath and the NHA_GROUP_TYPE is currently optional so this has
slipped through so far. Fix the attribute checking to handle support of
new group types.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Signed-off-by: ASSOGBA Emery <assogba.emery@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tls_sw_recvmsg() and tls_decrypt_done() can be run concurrently.
// tls_sw_recvmsg()
if (atomic_read(&ctx->decrypt_pending))
crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
else
reinit_completion(&ctx->async_wait.completion);
if (!pending && READ_ONCE(ctx->async_notify))
complete(&ctx->async_wait.completion);
Consider the scenario tls_decrypt_done() is about to run complete()
if (!pending && READ_ONCE(ctx->async_notify))
and tls_sw_recvmsg() reads decrypt_pending == 0, does reinit_completion(),
then tls_decrypt_done() runs complete(). This sequence of execution
results in wrong completion. Consequently, for next decrypt request,
it will not wait for completion, eventually on connection close, crypto
resources freed, there is no way to handle pending decrypt response.
This race condition can be avoided by having atomic_read() mutually
exclusive with atomic_dec_return(),complete().Intoduced spin lock to
ensure the mutual exclution.
Addressed similar problem in tx direction.
v1->v2:
- More readable commit message.
- Corrected the lock to fix new race scenario.
- Removed barrier which is not needed now.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new action is installed, firstuse field of 'tcf_t' is explicitly set
to 0. Value of zero means "new action, not yet used"; as a packet hits the
action, 'firstuse' is stamped with the current jiffies value.
tcf_tm_dump() should return 0 for firstuse if action has not yet been hit.
Fixes: 48d8ee1694dd ("net sched actions: aggregate dumping of actions timeinfo") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adb03115f459 ("net: get rid of an signed integer overflow in ip_idents_reserve()")
used atomic_cmpxchg to replace "atomic_add_return" inside the function
"ip_idents_reserve". The reason was to avoid UBSAN warning.
However, this change has caused performance degrade and in GCC-8,
fno-strict-overflow is now mapped to -fwrapv -fwrapv-pointer
and signed integer overflow is now undefined by default at all
optimization levels[1]. Moreover, it was a bug in UBSAN vs -fwrapv
/-fno-strict-overflow, so Let's revert it safely.
[1] https://gcc.gnu.org/gcc-8/changes.html
Suggested-by: Peter Zijlstra <peterz@infradead.org> Suggested-by: Eric Dumazet <edumazet@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Jiong Wang <jiongwang@huawei.com> Signed-off-by: Yuqi Jin <jinyuqi@huawei.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the traversal of the list is completed with list_for_each_entry(),
the iterator (node) will point to an invalid object. So passing this to
qrtr_local_enqueue() which is outside of the iterator block is erroneous
eventhough the object is not used.
So fix this by passing NULL to qrtr_local_enqueue().
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes data remnant seen when we fail to reserve space for a
nexthop group during a larger dump.
If we fail the reservation, we goto nla_put_failure and
cancel the message.
Reproduce with the following iproute2 commands:
=====================
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip link add dummy20 type dummy
ip link add dummy21 type dummy
ip link add dummy22 type dummy
ip link add dummy23 type dummy
ip link add dummy24 type dummy
ip link add dummy25 type dummy
ip link add dummy26 type dummy
ip link add dummy27 type dummy
ip link add dummy28 type dummy
ip link add dummy29 type dummy
ip link add dummy30 type dummy
ip link add dummy31 type dummy
ip link add dummy32 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip link set dummy3 up
ip link set dummy4 up
ip link set dummy5 up
ip link set dummy6 up
ip link set dummy7 up
ip link set dummy8 up
ip link set dummy9 up
ip link set dummy10 up
ip link set dummy11 up
ip link set dummy12 up
ip link set dummy13 up
ip link set dummy14 up
ip link set dummy15 up
ip link set dummy16 up
ip link set dummy17 up
ip link set dummy18 up
ip link set dummy19 up
ip link set dummy20 up
ip link set dummy21 up
ip link set dummy22 up
ip link set dummy23 up
ip link set dummy24 up
ip link set dummy25 up
ip link set dummy26 up
ip link set dummy27 up
ip link set dummy28 up
ip link set dummy29 up
ip link set dummy30 up
ip link set dummy31 up
ip link set dummy32 up
ip link set dummy33 up
ip link set dummy34 up
ip link set vrf-red up
ip link set vrf-blue up
ip link set dummyVRFred up
ip link set dummyVRFblue up
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip ro add 1.1.1.20/32 dev dummy20
ip ro add 1.1.1.21/32 dev dummy21
ip ro add 1.1.1.22/32 dev dummy22
ip ro add 1.1.1.23/32 dev dummy23
ip ro add 1.1.1.24/32 dev dummy24
ip ro add 1.1.1.25/32 dev dummy25
ip ro add 1.1.1.26/32 dev dummy26
ip ro add 1.1.1.27/32 dev dummy27
ip ro add 1.1.1.28/32 dev dummy28
ip ro add 1.1.1.29/32 dev dummy29
ip ro add 1.1.1.30/32 dev dummy30
ip ro add 1.1.1.31/32 dev dummy31
ip ro add 1.1.1.32/32 dev dummy32
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 20 via 1.1.1.20 dev dummy20
ip next add id 21 via 1.1.1.21 dev dummy21
ip next add id 22 via 1.1.1.22 dev dummy22
ip next add id 23 via 1.1.1.23 dev dummy23
ip next add id 24 via 1.1.1.24 dev dummy24
ip next add id 25 via 1.1.1.25 dev dummy25
ip next add id 26 via 1.1.1.26 dev dummy26
ip next add id 27 via 1.1.1.27 dev dummy27
ip next add id 28 via 1.1.1.28 dev dummy28
ip next add id 29 via 1.1.1.29 dev dummy29
ip next add id 30 via 1.1.1.30 dev dummy30
ip next add id 31 via 1.1.1.31 dev dummy31
ip next add id 32 via 1.1.1.32 dev dummy32
i=100
while [ $i -le 200 ]
do
ip next add id $i group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
echo $i
((i++))
done
ip next add id 999 group 1/2/3/4/5/6
ip next ls
========================
Fixes: ab84be7e54fc ("net: Initial nexthop code") Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc32, it was:
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com> Tested-by: Matteo Croce <mcroce@redhat.com> Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When FW response to commands is very slow and all command entries in
use are waiting for completion we can have a race where commands can get
timeout before they get out of the queue and handled. Timeout
completion on uninitialized command will cause releasing command's
buffers before accessing it for initialization and then we will get NULL
pointer exception while trying access it. It may also cause releasing
buffers of another command since we may have timeout completion before
even allocating entry index for this command.
Add entry handling completion to avoid this race.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error with MPLS support the code is misusing AF_INET
instead of AF_MPLS.
Fixes: 1b69e7e6c4da ("ipip: support MPLS over IPv4") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
added a bind-address cache in tb->fast*. The tb->fast* caches the address
of a sk which has successfully been binded with SO_REUSEPORT ON. The idea
is to avoid the expensive conflict search in inet_csk_bind_conflict().
There is an issue with wildcard matching where sk_reuseport_match() should
have returned false but it is currently returning true. It ends up
hiding bind conflict. For example,
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::2]:443"); /* with SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. Still Succeed where it shouldn't */
The last bind("[::]:443") with SO_REUSEPORT on should have failed because
it should have a conflict with the very first bind("[::1]:443") which
has SO_REUSEPORT off. However, the address "[::2]" is cached in
tb->fast* in the second bind. In the last bind, the sk_reuseport_match()
returns true because the binding sk's wildcard addr "[::]" matches with
the "[::2]" cached in tb->fast*.
The correct bind conflict is reported by removing the second
bind such that tb->fast* cache is not involved and forces the
bind("[::]:443") to go through the inet_csk_bind_conflict():
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. -EADDRINUSE */
The expected behavior for sk_reuseport_match() is, it should only allow
the "cached" tb->fast* address to be used as a wildcard match but not
the address of the binding sk. To do that, the current
"bool match_wildcard" arg is split into
"bool match_sk1_wildcard" and "bool match_sk2_wildcard".
This change only affects the sk_reuseport_match() which is only
used by inet_csk (e.g. TCP).
The other use cases are calling inet_rcv_saddr_equal() and
this patch makes it pass the same "match_wildcard" arg twice to
the "ipv[46]_rcv_saddr_equal(..., match_wildcard, match_wildcard)".
Cc: Josef Bacik <jbacik@fb.com> Fixes: 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk") Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__netif_receive_skb_core may change the skb pointer passed into it (e.g.
in rx_handler). The original skb may be freed as a result of this
operation.
The callers of __netif_receive_skb_core may further process original skb
by using pt_prev pointer returned by __netif_receive_skb_core thus
leading to unpleasant effects.
The solution is to pass skb by reference into __netif_receive_skb_core.
v2: Added Fixes tag and comment regarding ppt_prev and skb invariant.
Fixes: 88eb1944e18c ("net: core: propagate SKB lists through packet_type lookup") Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
