Paolo Abeni [Wed, 23 Jul 2025 14:32:23 +0000 (16:32 +0200)]
mptcp: track fallbacks accurately via mibs
Add the mibs required to cover the few possible fallback causes still
lacking suck info.
Move the relevant mib increment into the fallback helper, so that no
eventual future fallback operation will miss a paired mib increment.
Additionally track failed fallback via its own mib, such mib is
incremented only when a fallback mandated by the protocol fails - due to
racing subflow creation.
While at the above, rename an existing helper to reduce long lines
problems all along.
selftests: net: Skip test if IPv6 is not configured
Extend the `check_for_dependencies()` function in `lib_netcons.sh` to check
whether IPv6 is enabled by verifying the existence of
`/proc/net/if_inet6`. Having IPv6 is a now a dependency of netconsole
tests. If the file does not exist, the script will skip the test with an
appropriate message suggesting to verify if `CONFIG_IPV6` is enabled.
This prevents the test to misbehave if IPv6 is not configured.
Yi Cong [Thu, 24 Jul 2025 01:31:33 +0000 (09:31 +0800)]
usbnet: Set duplex status to unknown in the absence of MII
Currently, USB CDC devices that do not use MDIO to get link status have
their duplex mode set to half-duplex by default. However, since the CDC
specification does not define a duplex status, this can be misleading.
This patch changes the default to DUPLEX_UNKNOWN in the absence of MII,
which more accurately reflects the state of the link and avoids implying
an incorrect or error state.
Which is similar to recent syzkaller reports in [0] and [1] and triggers
because macsec does not advertise IFF_UNICAST_FLT although it has proper
ndo_set_rx_mode callback that takes care of pushing uc/mc addresses
down to the real device.
In general, dev_uc_add call path is problematic for stacking
non-IFF_UNICAST_FLT because we might grab netdev instance lock under
addr_list_lock spinlock, so this is not a systemic fix.
net: hibmcge: support for statistics of reset failures
Add a statistical item to count the number of reset failures.
This statistical item can be queried using ethtool -S or
reported through diagnose information.
====================
selftests: drv-net: Fix and improve command requirement checking
This series fixes remote command checking and cleans up command
requirement calls across tests.
The first patch fixes require_cmd() incorrectly checking commands
locally even when remote=True was specified due to a missing host
parameter.
The second patch makes require_cmd() usage explicit about local/remote
requirements, avoiding unnecessary test failures and consolidating
duplicate calls.
====================
Gal Pressman [Wed, 23 Jul 2025 13:54:54 +0000 (16:54 +0300)]
selftests: drv-net: Make command requirements explicit
Make require_cmd() calls explicit about whether commands are needed
locally, remotely, or both.
Since require_cmd() defaults to local=True, tests should explicitly set
local=False when commands are only needed remotely.
- socat: Set local=False since it's only needed on remote hosts.
- iperf3: Use single call with both local=True and remote=True since
it's needed on both hosts.
This avoids unnecessary test failures when commands are missing locally
but available remotely where actually needed, and consolidates a
duplicate require_cmd() call into single call that checks both hosts.
Fixes: 0d0f4174f6c8 ("selftests: drv-net: add a simple TSO test") Fixes: f1e68a1a4a40 ("selftests: drv-net: add require_XYZ() helpers for validating env") Fixes: c76bab22e920 ("selftests: drv-net: rss_input_xfrm: Check test prerequisites before running") Reviewed-by: Nimrod Oren <noren@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20250723135454.649342-3-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building, the following warnings will appear.
"
pci_irq.c: In function ‘mlx5_ctrl_irq_request’:
pci_irq.c:494:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
pci_irq.c: In function ‘mlx5_irq_request_vector’:
pci_irq.c:561:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
eq.c: In function ‘comp_irq_request_sf’:
eq.c:897:1: warning: the frame size of 1080 bytes is larger than 1024 bytes [-Wframe-larger-than=]
irq_affinity.c: In function ‘irq_pool_request_irq’:
irq_affinity.c:74:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
"
These warnings indicate that the stack frame size exceeds 1024 bytes in
these functions.
To resolve this, instead of allocating large memory buffers on the stack,
it is better to use kvzalloc to allocate memory dynamically on the heap.
This approach reduces stack usage and eliminates these frame size warnings.
====================
Use enum to represent the NAPI threaded state
Instead of using 0/1 to represent the NAPI threaded states use enum
(disabled/enabled) to represent the NAPI threaded states.
This patch series is a subset of patches from the following patch series:
https://lore.kernel.org/20250718232052.1266188-1-skhawaja@google.com
The first 3 patches are being sent separately as per the feedback to
replace the usage of 0/1 as NAPI threaded states with enum. See:
https://lore.kernel.org/20250721164856.1d2208e4@kernel.org
====================
Instead of using '0' and '1' for napi threaded state use an enum with
'disabled' and 'enabled' states.
Tested:
./tools/testing/selftests/net/nl_netdev.py
TAP version 13
1..7
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
ok 3 nl_netdev.page_pool_check
ok 4 nl_netdev.napi_list_check
ok 5 nl_netdev.dev_set_threaded
ok 6 nl_netdev.napi_set_threaded
ok 7 nl_netdev.nsim_rxq_reset_down
# Totals: pass:7 fail:0 xfail:0 xpass:0 skip:0 error:0
net: Use netif_threaded_enable instead of netif_set_threaded in drivers
Prepare for adding an enum type for NAPI threaded states by adding
netif_threaded_enable API. De-export the existing netif_set_threaded API
and only use it internally. Update existing drivers to use
netif_threaded_enable instead of the de-exported netif_set_threaded.
Note that dev_set_threaded used by mt76 debugfs file is unchanged.
Jakub Kicinski [Fri, 25 Jul 2025 01:12:54 +0000 (18:12 -0700)]
Merge tag 'for-net-next-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
core:
- hci_sync: fix double free in 'hci_discovery_filter_clear()'
- hci_event: Mask data status from LE ext adv reports
- hci_devcd_dump: fix out-of-bounds via dev_coredumpv
- ISO: add socket option to report packet seqnum via CMSG
- hci_event: Add support for handling LE BIG Sync Lost event
- ISO: Support SCM_TIMESTAMPING for ISO TS
- hci_core: Add PA_LINK to distinguish BIG sync and PA sync connections
- hci_sock: Reset cookie to zero in hci_sock_free_cookie()
drivers:
- btusb: Add new VID/PID 0489/e14e for MT7925
- btusb: Add a new VID/PID 2c7c/7009 for MT7925
- btusb: Add RTL8852BE device 0x13d3:0x3618
- btusb: Add support for variant of RTL8851BE (USB ID 13d3:3601)
- btusb: Add USB ID 3625:010b for TP-LINK Archer TX10UB Nano
- btusb: QCA: Support downloading custom-made firmwares
- btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
- nxp: add support for supply and reset
- btnxpuart: Add support for 4M baudrate
- btnxpuart: Correct the Independent Reset handling after FW dump
- btnxpuart: Add uevents for FW dump and FW download complete
- btintel: Define a macro for Intel Reset vendor command
- btintel_pcie: Support Function level reset
- btintel_pcie: Add support for device 0x4d76
- btintel_pcie: Make driver wait for alive interrupt
- btintel_pcie: Fix Alive Context State Handling
- hci_qca: Enable ISO data packet RX
* tag 'for-net-next-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (42 commits)
Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections
Bluetooth: hci_event: Mask data status from LE ext adv reports
Bluetooth: btintel_pcie: Fix Alive Context State Handling
Bluetooth: btintel_pcie: Make driver wait for alive interrupt
Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv
Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()'
Bluetooth: btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
Bluetooth: btusb: Sort WCN6855 device IDs by VID and PID
Bluetooth: btusb: QCA: Support downloading custom-made firmwares
Bluetooth: btnxpuart: Add uevents for FW dump and FW download complete
Bluetooth: btnxpuart: Correct the Independent Reset handling after FW dump
Bluetooth: ISO: Support SCM_TIMESTAMPING for ISO TS
Bluetooth: ISO: add socket option to report packet seqnum via CMSG
Bluetooth: btintel: Define a macro for Intel Reset vendor command
Bluetooth: Fix typos in comments
Bluetooth: RFCOMM: Fix typos in comments
Bluetooth: aosp: Fix typo in comment
Bluetooth: hci_bcm4377: Fix typo in comment
Bluetooth: btrtl: Fix typo in comment
Bluetooth: btmtk: Fix typo in log string
...
====================
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 4 files changed, 40 insertions(+), 15 deletions(-).
The main changes are:
1) Improved verifier error message for incorrect narrower load from
pointer field in ctx, from Paul Chaignon.
2) Disabled migration in nf_hook_run_bpf to address a syzbot report,
from Kuniyuki Iwashima.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
selftests/bpf: Test invalid narrower ctx load
bpf: Reject narrower access to pointer ctx fields
bpf: Disable migration in nf_hook_run_bpf().
====================
====================
tools: ynl-gen: print setters for multi-val attrs
ncdevmem seems to manually prepare the queue attributes.
This is not ideal, YNL should be providing helpers for this.
Make YNL output allocation and setter helpers for multi-val attrs.
Jakub Kicinski [Wed, 23 Jul 2025 17:10:46 +0000 (10:10 -0700)]
selftests: drv-net: devmem: use new mattr ynl helpers
Use the just-added YNL helpers instead of manually setting
"_present" bits in the queue attrs. Compile tested only.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Acked-by: Mina Almasry <almasrymina@google.com> Link: https://patch.msgid.link/20250723171046.4027470-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 23 Jul 2025 17:10:45 +0000 (10:10 -0700)]
tools: ynl-gen: print setters for multi-val attrs
For basic types we "flatten" setters. If a request "a" has a simple
nest "b" with value "val" we print helpers like:
req_set_a_b(struct a *req, int val)
{
req->_present.a = 1;
req->b._present.val = 1;
req->b.val = ...
}
This is not possible for multi-attr because they have to be allocated
dynamically by the user. Print "object level" setters so that user
preparing the object doesn't have to futz with the presence bits
and other YNL internals.
Add the ability to pass in the variable name to generated setters.
Using "req" here doesn't feel right, while the attr is part of a request
it's not the request itself, so it seems cleaner to call it "obj".
Jakub Kicinski [Wed, 23 Jul 2025 17:10:44 +0000 (10:10 -0700)]
tools: ynl-gen: print alloc helper for multi-val attrs
In general YNL provides allocation and free helpers for types.
For pure nested structs which are used as multi-attr (and therefore
have to be allocated dynamically) we already print a free helper
as it's needed by free of the containing struct.
Add printing of the alloc helper for consistency. The helper
takes the number of entries to allocate as an argument, e.g.:
Jakub Kicinski [Wed, 23 Jul 2025 17:10:43 +0000 (10:10 -0700)]
tools: ynl-gen: move free printing to the print_type_full() helper
Just to avoid making the main function even more enormous,
before adding more things to print move the free printing
to a helper which already prints the type.
Jakub Kicinski [Fri, 25 Jul 2025 00:25:42 +0000 (17:25 -0700)]
Merge tag 'wireless-next-2025-07-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another wireless update:
- rtw89:
- STA+P2P concurrency
- support for USB devices RTL8851BU/RTL8852BU
- ath9k: OF support
- ath12k:
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- iwlwifi: some FIPS interoperability
- brcm80211: support SDIO 43751 device
- rt2x00: better DT/OF support
- cfg80211/mac80211:
- improved S1G support
- beacon monitor for MLO
* tag 'wireless-next-2025-07-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (199 commits)
ssb: use new GPIO line value setter callbacks for the second GPIO chip
wifi: Fix typos
wifi: brcmsmac: Use str_true_false() helper
wifi: brcmfmac: fix EXTSAE WPA3 connection failure due to AUTH TX failure
wifi: brcm80211: Remove yet more unused functions
wifi: brcm80211: Remove more unused functions
wifi: brcm80211: Remove unused functions
wifi: iwlwifi: Revert "wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions"
wifi: iwlwifi: check validity of the FW API range
wifi: iwlwifi: don't export symbols that we shouldn't
wifi: iwlwifi: mld: use spec link id and not FW link id
wifi: iwlwifi: mld: decode EOF bit for AMPDUs
wifi: iwlwifi: Remove support for rx OMI bandwidth reduction
wifi: iwlwifi: stop supporting iwl_omi_send_status_notif ver 1
wifi: iwlwifi: remove SC2F firmware support
wifi: iwlwifi: mvm: Remove NAN support
wifi: iwlwifi: mld: avoid outdated reorder buffer head_sn
wifi: iwlwifi: mvm: avoid outdated reorder buffer head_sn
wifi: iwlwifi: disable certain features for fips_enabled
wifi: iwlwifi: mld: support channel survey collection for ACS scans
...
====================
Merge tag 'net-6.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and xfrm.
The TI regression notified last week is actually on our net-next tree,
it does not affect 6.16.
We are investigating a virtio regression which is quite hard to
reproduce - currently only our CI sporadically hits it. Hopefully it
should not be critical, and I'm not sure that an additional week would
be enough to solve it.
Current release - fix to a fix:
- sched: sch_qfq: avoid sleeping in atomic context in qfq_delete_class
Previous releases - regressions:
- xfrm:
- set transport header to fix UDP GRO handling
- delete x->tunnel as we delete x
- eth:
- mlx5: fix memory leak in cmd_exec()
- i40e: when removing VF MAC filters, avoid losing PF-set MAC
- gve: fix stuck TX queue for DQ queue format
Previous releases - always broken:
- can: fix NULL pointer deref of struct can_priv::do_set_mode
- eth:
- ice: fix a null pointer dereference in ice_copy_and_init_pkg()
- ism: fix concurrency management in ism_cmd()
- dpaa2: fix device reference count leak in MAC endpoint handling
- icssg-prueth: fix buffer allocation for ICSSG
Misc:
- selftests: mptcp: increase code coverage"
* tag 'net-6.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (34 commits)
net: hns3: default enable tx bounce buffer when smmu enabled
net: hns3: fixed vf get max channels bug
net: hns3: disable interrupt when ptp init failed
net: hns3: fix concurrent setting vlan filter issue
s390/ism: fix concurrency management in ism_cmd()
selftests: drv-net: wait for iperf client to stop sending
MAINTAINERS: Add in6.h to MAINTAINERS
selftests: netfilter: tone-down conntrack clash test
can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode
net/sched: sch_qfq: Avoid triggering might_sleep in atomic context in qfq_delete_class
gve: Fix stuck TX queue for DQ queue format
net: appletalk: Fix use-after-free in AARP proxy probe
net: bcmasp: Restore programming of TX map vector register
selftests: mptcp: connect: also cover checksum
selftests: mptcp: connect: also cover alt modes
e1000e: ignore uninitialized checksum word on tgp
e1000e: disregard NVM checksum on tgp when valid checksum bit is not set
ice: Fix a null pointer dereference in ice_copy_and_init_pkg()
i40e: When removing VF MAC filters, only check PF-set MAC
i40e: report VF tx_dropped with tx_errors instead of tx_discards
...
1) Optimize to hold device only for the asynchronous decryption,
where it is really needed.
From Jianbo Liu.
2) Align our inbund SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup.
From Aakash Kumar S.
3) Skip redundant statistics update for xfrm crypto offload.
From Jianbo Liu.
Please pull or let me know if there are problems.
* tag 'ipsec-next-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: Skip redundant statistics update for crypto offload
xfrm: Duplicate SPI Handling
xfrm: hold device only for the asynchronous decryption
====================
1) Premption fixes for xfrm_state_find.
From Sabrina Dubroca.
2) Initialize offload path also for SW IPsec GRO. This fixes a
performance regression on SW IPsec offload.
From Leon Romanovsky.
3) Fix IPsec UDP GRO for IKE packets.
From Tobias Brunner,
4) Fix transport header setting for IPcomp after decompressing.
From Fernando Fernandez Mancera.
5) Fix use-after-free when xfrmi_changelink tries to change
collect_md for a xfrm interface.
From Eyal Birger .
6) Delete the special IPcomp x->tunnel state along with the state x
to avoid refcount problems.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
* tag 'ipsec-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
Revert "xfrm: destroy xfrm_state synchronously on net exit path"
xfrm: delete x->tunnel as we delete x
xfrm: interface: fix use-after-free after changing collect_md xfrm interface
xfrm: ipcomp: adjust transport header after decompressing
xfrm: Set transport header to fix UDP GRO handling
xfrm: always initialize offload path
xfrm: state: use a consistent pcpu_id in xfrm_state_find
xfrm: state: initialize state_ptrs earlier in xfrm_state_find
====================
net: hns3: default enable tx bounce buffer when smmu enabled
The SMMU engine on HIP09 chip has a hardware issue.
SMMU pagetable prefetch features may prefetch and use a invalid PTE
even the PTE is valid at that time. This will cause the device trigger
fake pagefaults. The solution is to avoid prefetching by adding a
SYNC command when smmu mapping a iova. But the performance of nic has a
sharp drop. Then we do this workaround, always enable tx bounce buffer,
avoid mapping/unmapping on TX path.
This issue only affects HNS3, so we always enable
tx bounce buffer when smmu enabled to improve performance.
Fixes: 295ba232a8c3 ("net: hns3: add device version to replace pci revision") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250722125423.1270673-5-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the queried maximum of vf channels is the maximum of channels
supported by each TC. However, the actual maximum of channels is
the maximum of channels supported by the device.
Fixes: 849e46077689 ("net: hns3: add ethtool_ops.get_channels support for VF") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250722125423.1270673-4-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The vport->req_vlan_fltr_en may be changed concurrently by function
hclge_sync_vlan_fltr_state() called in periodic work task and
function hclge_enable_vport_vlan_filter() called by user configuration.
It may cause the user configuration inoperative. Fixes it by protect
the vport->req_vlan_fltr by vport_lock.
Fixes: 2ba306627f59 ("net: hns3: add support for modify VLAN filter state") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250722125423.1270673-2-shaojijie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Halil Pasic [Tue, 22 Jul 2025 16:18:17 +0000 (18:18 +0200)]
s390/ism: fix concurrency management in ism_cmd()
The s390x ISM device data sheet clearly states that only one
request-response sequence is allowable per ISM function at any point in
time. Unfortunately as of today the s390/ism driver in Linux does not
honor that requirement. This patch aims to rectify that.
This problem was discovered based on Aliaksei's bug report which states
that for certain workloads the ISM functions end up entering error state
(with PEC 2 as seen from the logs) after a while and as a consequence
connections handled by the respective function break, and for future
connection requests the ISM device is not considered -- given it is in a
dysfunctional state. During further debugging PEC 3A was observed as
well.
A kernel message like
[ 1211.244319] zpci: 061a:00:00.0: Event 0x2 reports an error for PCI function 0x61a
is a reliable indicator of the stated function entering error state
with PEC 2. Let me also point out that a kernel message like
[ 1211.244325] zpci: 061a:00:00.0: The ism driver bound to the device does not support error recovery
is a reliable indicator that the ISM function won't be auto-recovered
because the ISM driver currently lacks support for it.
On a technical level, without this synchronization, commands (inputs to
the FW) may be partially or fully overwritten (corrupted) by another CPU
trying to issue commands on the same function. There is hard evidence that
this can lead to DMB token values being used as DMB IOVAs, leading to
PEC 2 PCI events indicating invalid DMA. But this is only one of the
failure modes imaginable. In theory even completely losing one command
and executing another one twice and then trying to interpret the outputs
as if the command we intended to execute was actually executed and not
the other one is also possible. Frankly, I don't feel confident about
providing an exhaustive list of possible consequences.
Fixes: 684b89bc39ce ("s390/ism: add device driver for internal shared memory") Reported-by: Aliaksei Makarau <Aliaksei.Makarau@ibm.com> Tested-by: Mahanta Jambigi <mjambigi@linux.ibm.com> Tested-by: Aliaksei Makarau <Aliaksei.Makarau@ibm.com> Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250722161817.1298473-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ssb: use new GPIO line value setter callbacks for the second GPIO chip
Because the other chip is guarded in an unlikely ifdef, I missed it when
converting this driver. Fix it now.
Fixes: 757259db79fc ("ssb: use new GPIO line value setter callbacks") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Link: https://patch.msgid.link/20250723141257.51412-1-brgl@bgdev.pl Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paul Chaignon [Tue, 22 Jul 2025 14:33:37 +0000 (16:33 +0200)]
selftests/bpf: Test invalid narrower ctx load
This patch adds selftests to cover invalid narrower loads on the
context. These used to cause kernel warnings before the previous patch.
To trigger the warning, the load had to be aligned, to read an affected
context field (ex., skb->sk), and not starting at the beginning of the
field.
The nine new cases all fail without the previous patch.
Paul Chaignon [Tue, 22 Jul 2025 14:32:32 +0000 (16:32 +0200)]
bpf: Reject narrower access to pointer ctx fields
The following BPF program, simplified from a syzkaller repro, causes a
kernel warning:
r0 = *(u8 *)(r1 + 169);
exit;
With pointer field sk being at offset 168 in __sk_buff. This access is
detected as a narrower read in bpf_skb_is_valid_access because it
doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed
and later proceeds to bpf_convert_ctx_access. Note that for the
"is_narrower_load" case in the convert_ctx_accesses(), the insn->off
is aligned, so the cnt may not be 0 because it matches the
offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However,
the target_size stays 0 and the verifier errors with a kernel warning:
verifier bug: error during ctx access conversion(1)
This patch fixes that to return a proper "invalid bpf_context access
off=X size=Y" error on the load instruction.
The same issue affects multiple other fields in context structures that
allow narrow access. Some other non-affected fields (for sk_msg,
sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for
consistency.
Note this syzkaller crash was reported in the "Closes" link below, which
used to be about a different bug, fixed in
commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions
in insn_def_regno()"). Because syzbot somehow confused the two bugs,
the new crash and repro didn't get reported to the mailing list.
Fixes: f96da09473b52 ("bpf: simplify narrower ctx access") Fixes: 0df1a55afa832 ("bpf: Warn on internal verifier errors") Reported-by: syzbot+0ef84a7bdf5301d4cbec@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=0ef84a7bdf5301d4cbec Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com> Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Acked-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://patch.msgid.link/3b8dcee67ff4296903351a974ddd9c4dca768b64.1753194596.git.paul.chaignon@gmail.com
Merge tag 'drm-fixes-2025-07-24' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"This might just be part one, but I'm sending it a bit early as it has
two sets of reverts for regressions, one is all the gem/dma-buf
handling and another was a nouveau ioctl change.
Otherwise there is an amdgpu fix, nouveau fix and a scheduler fix.
If any other changes come in I'll follow up with another more usual
Fri/Sat MR.
gem:
- revert all the dma-buf/gem changes as there as lifetime issues
with them
nouveau:
- revert an ioctl change as it causes issues
- fix NULL ptr on fermi
bridge:
- remove extra semicolon
sched:
- remove hang causing optimisation
amdgpu:
- fix garbage in cleared vram after resume"
* tag 'drm-fixes-2025-07-24' of https://gitlab.freedesktop.org/drm/kernel:
drm/bridge: ti-sn65dsi86: Remove extra semicolon in ti_sn_bridge_probe()
Revert "drm/nouveau: check ioctl command codes better"
drm/nouveau/nvif: fix null ptr deref on pre-fermi boards
Revert "drm/gem-dma: Use dma_buf from GEM object instance"
Revert "drm/gem-shmem: Use dma_buf from GEM object instance"
Revert "drm/gem-framebuffer: Use dma_buf from GEM object instance"
Revert "drm/prime: Use dma_buf from GEM object instance"
Revert "drm/etnaviv: Use dma_buf from GEM object instance"
Revert "drm/vmwgfx: Use dma_buf from GEM object instance"
Revert "drm/virtio: Use dma_buf from GEM object instance"
drm/sched: Remove optimization that causes hang when killing dependent jobs
drm/amdgpu: Reset the clear flag in buddy during resume
selftests: drv-net: wait for iperf client to stop sending
A few packets may still be sent out during the termination of iperf
processes. These late packets cause failures in rss_ctx.py when they
arrive on queues expected to be empty.
Jakub Kicinski [Thu, 24 Jul 2025 00:52:10 +0000 (17:52 -0700)]
Merge branch 'dualpi2-patch'
Chia-Yu Chang says:
====================
DUALPI2 patch
This patch serise adds DualPI Improved with a Square (DualPI2) with
following features:
* Supports congestion controls that comply with the Prague requirements
in RFC9331 (e.g. TCP-Prague)
* Coupled dual-queue that separates the L4S traffic in a low latency
queue (L-queue), without harming remaining traffic that is scheduled
in classic queue (C-queue) due to congestion-coupling using PI2
as defined in RFC9332
* Configurable overload strategies
* Use of sojourn time to reliably estimate queue delay
* Supports ECN L4S-identifier (IP.ECN==0b*1) to classify traffic into
respective queues
For more details of DualPI2, please refer IETF RFC9332
(https://datatracker.ietf.org/doc/html/rfc9332).
====================
Introduce the specification of tc qdisc DualPI2 stats and attributes,
which is the reference implementation of IETF RFC9332 DualQ Coupled AQM
(https://datatracker.ietf.org/doc/html/rfc9332) providing two different
queues: low latency queue (L-queue) and classic queue (C-queue).
selftests/tc-testing: Add selftests for qdisc DualPI2
Update configuration of tc-tests and preload DualPI2 module for self-tests,
and add following self-test cases for DualPI2:
Test a4c7: Create DualPI2 with default setting
Test 1ea4: Create DualPI2 with memlimit
Test 2130: Create DualPI2 with typical_rtt and max_rtt
Test 90c1: Create DualPI2 with max_rtt
Test 7b3c: Create DualPI2 with any_ect option
Test 49a3: Create DualPI2 with overflow option
Test d0a1: Create DualPI2 with drop_enqueue option
Test f051: Create DualPI2 with no_split_gso option
Test 456b: Create DualPI2 with packet step_thresh
Test 610c: Create DualPI2 with packet min_qlen_step
Test b4fa: Create DualPI2 with packet coupling_factor
Test 37f1: Create DualPI2 with packet classic_protection
DualPI2 provides L4S-type low latency & loss to traffic that uses a
scalable congestion controller (e.g. TCP-Prague, DCTCP) without
degrading the performance of 'classic' traffic (e.g. Reno,
Cubic etc.). It is to be the reference implementation of IETF RFC9332
DualQ Coupled AQM (https://datatracker.ietf.org/doc/html/rfc9332).
Note that creating two independent queues cannot meet the goal of
DualPI2 mentioned in RFC9332: "...to preserve fairness between
ECN-capable and non-ECN-capable traffic." Further, it could even
lead to starvation of Classic traffic, which is also inconsistent
with the requirements in RFC9332: "...although priority MUST be
bounded in order not to starve Classic traffic." DualPI2 is
designed to maintain approximate per-flow fairness on L-queue and
C-queue by forming a single qdisc using the coupling factor and
scheduler between two queues.
The qdisc provides two queues called low latency and classic. It
classifies packets based on the ECN field in the IP headers. By
default it directs non-ECN and ECT(0) into the classic queue and
ECT(1) and CE into the low latency queue, as per the IETF spec.
Each queue runs its own AQM:
* The classic AQM is called PI2, which is similar to the PIE AQM but
more responsive and simpler. Classic traffic requires a decent
target queue (default 15ms for Internet deployment) to fully
utilize the link and to avoid high drop rates.
* The low latency AQM is, by default, a very shallow ECN marking
threshold (1ms) similar to that used for DCTCP.
The DualQ isolates the low queuing delay of the Low Latency queue
from the larger delay of the 'Classic' queue. However, from a
bandwidth perspective, flows in either queue will share out the link
capacity as if there was just a single queue. This bandwidth pooling
effect is achieved by coupling together the drop and ECN-marking
probabilities of the two AQMs.
The PI2 AQM has two main parameters in addition to its target delay.
The integral gain factor alpha is used to slowly correct any persistent
standing queue error from the target delay, while the proportional gain
factor beta is used to quickly compensate for queue changes (growth or
shrinkage). Either alpha and beta are given as a parameter, or they can
be calculated by tc from alternative typical and maximum RTT parameters.
Internally, the output of a linear Proportional Integral (PI)
controller is used for both queues. This output is squared to
calculate the drop or ECN-marking probability of the classic queue.
This counterbalances the square-root rate equation of Reno/Cubic,
which is the trick that balances flow rates across the queues. For
the ECN-marking probability of the low latency queue, the output of
the base AQM is multiplied by a coupling factor. This determines the
balance between the flow rates in each queue. The default setting
makes the flow rates roughly equal, which should be generally
applicable.
If DUALPI2 AQM has detected overload (due to excessive non-responsive
traffic in either queue), it will switch to signaling congestion
solely using drop, irrespective of the ECN field. Alternatively, it
can be configured to limit the drop probability and let the queue
grow and eventually overflow (like tail-drop).
GSO splitting in DUALPI2 is configurable from userspace while the
default behavior is to split gso. When running DUALPI2 at unshaped
10gigE with 4 download streams test, splitting gso apart results in
halving the latency with no loss in throughput:
sched: Dump configuration and statistics of dualpi2 qdisc
The configuration and statistics dump of the DualPI2 Qdisc provides
information related to both queues, such as packet numbers and queuing
delays in the L-queue and C-queue, as well as general information such as
probability value, WRR credits, memory usage, packet marking counters, max
queue size, etc.
The following patch includes enqueue/dequeue for DualPI2.
sched: Struct definition and parsing of dualpi2 qdisc
DualPI2 is the reference implementation of IETF RFC9332 DualQ Coupled
AQM (https://datatracker.ietf.org/doc/html/rfc9332) providing two
queues called low latency (L-queue) and classic (C-queue). By default,
it enqueues non-ECN and ECT(0) packets into the C-queue and ECT(1) and
CE packets into the low latency queue (L-queue), as per IETF RFC9332 spec.
This patch defines the dualpi2 Qdisc structure and parsing, and the
following two patches include dumping and enqueue/dequeue for the DualPI2.
The first step towards that is splitting struct page by its individual
users, as has already been done with folio and slab. This patchset does
that for page pool.
Matthew Wilcox tried and stopped the same work, you can see in:
I focused on removing the page pool members in struct page this time,
not moving the allocation code of page pool from net to mm. It can be
done later if needed.
====================
Byungchul Park [Mon, 21 Jul 2025 02:18:26 +0000 (11:18 +0900)]
netmem, mlx4: access ->pp_ref_count through netmem_desc instead of page
To eliminate the use of struct page in page pool, the page pool users
should use netmem descriptor and APIs instead.
Make mlx4 access ->pp_ref_count through netmem_desc instead of page.
While at it, add a helper, pp_page_to_nmdesc() and __pp_page_to_nmdesc(),
that can be used to get netmem_desc from page only if it's a pp page.
For now that netmem_desc overlays on page, it can be achieved by just
casting, and use macro and _Generic to cover const casting as well.
Plus, change page_pool_page_is_pp() to check for 'const struct page *'
instead of 'struct page *' since it doesn't modify data and additionally
covers const type.
Byungchul Park [Mon, 21 Jul 2025 02:18:25 +0000 (11:18 +0900)]
netmem: use netmem_desc instead of page to access ->pp in __netmem_get_pp()
To eliminate the use of the page pool fields in struct page, the page
pool code should use netmem descriptor and APIs instead.
However, __netmem_get_pp() still accesses ->pp via struct page. So
change it to use struct netmem_desc instead, since ->pp no longer will
be available in struct page.
While at it, add a helper, __netmem_to_nmdesc(), that can be used to
unsafely get pointer to netmem_desc backing the netmem_ref, only when
the netmem_ref is always backed by system memory.
To simplify struct page, the page pool members of struct page should be
moved to other, allowing these members to be removed from struct page.
Introduce a network memory descriptor to store the members, struct
netmem_desc, and make it union'ed with the existing fields in struct
net_iov, allowing to organize the fields of struct net_iov.
Signed-off-by: Byungchul Park <byungchul@sk.com> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Mina Almasry <almasrymina@google.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Harry Yoo <harry.yoo@oracle.com> Link: https://patch.msgid.link/20250721021835.63939-2-byungchul@sk.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdevsim emulates firmware update and it takes 5 seconds to complete.
For some use cases, this is too long and unnecessary. Allow user to
configure the time by exposing debugfs a knob to set chunk time.
devlink: Fix excessive stack usage in rate TC bandwidth parsing
The devlink_nl_rate_tc_bw_parse function uses a large stack array for
devlink attributes, which triggers a warning about excessive stack
usage:
net/devlink/rate.c: In function 'devlink_nl_rate_tc_bw_parse':
net/devlink/rate.c:382:1: error: the frame size of 1648 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
Introduce a separate attribute set specifically for rate TC bandwidth
parsing that only contains the two attributes actually used: index
and bandwidth. This reduces the stack array from DEVLINK_ATTR_MAX
entries to just 2 entries, solving the stack usage issue.
Update devlink selftest to use the new 'index' and 'bw' attribute names
consistent with the YAML spec.
My CC-adding automation returned nothing on a future patch to the
include/linux/in6.h file, and I went looking for why. Add the missed
in6.h to MAINTAINERS.
Manuel Andreas [Wed, 23 Jul 2025 15:51:20 +0000 (17:51 +0200)]
KVM: x86/xen: Fix cleanup logic in emulation of Xen schedop poll hypercalls
kvm_xen_schedop_poll does a kmalloc_array() when a VM polls the host
for more than one event channel potr (nr_ports > 1).
After the kmalloc_array(), the error paths need to go through the
"out" label, but the call to kvm_read_guest_virt() does not.
Fixes: 92c58965e965 ("KVM: x86/xen: Use kvm_read_guest_virt() instead of open-coding it badly") Reviewed-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Manuel Andreas <manuel.andreas@tum.de>
[Adjusted commit message. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Airlie [Wed, 23 Jul 2025 20:49:38 +0000 (06:49 +1000)]
Merge tag 'drm-misc-fixes-2025-07-23' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v6.16-rc8/final?:
- Revert all uses of drm_gem_object->dmabuf to
drm_gem_object->import_attach->dmabuf.
- Fix amdgpu returning BIOS cluttered VRAM after resume.
- Scheduler hang fix.
- Revert nouveau ioctl fix as it caused regressions.
- Fix null pointer deref in nouveau.
- Fix unnecessary semicolon in ti_sn_bridge_probe.
Al Viro [Sun, 20 Jul 2025 20:43:53 +0000 (16:43 -0400)]
fix the regression in ufs options parsing
A really dumb braino on rebasing and a dumber fuckup with managing #for-next
Fixes: b70cb459890b ("ufs: convert ufs to the new mount API") Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Yang Li [Thu, 10 Jul 2025 10:52:47 +0000 (18:52 +0800)]
Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections
Currently, BIS_LINK is used for both BIG sync and PA sync connections,
which makes it impossible to distinguish them when searching for a PA
sync connection.
Adding PA_LINK will make the distinction clearer and simplify future
extensions for PA-related features.
Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Down [Mon, 21 Jul 2025 15:30:23 +0000 (16:30 +0100)]
Bluetooth: hci_event: Mask data status from LE ext adv reports
The Event_Type field in an LE Extended Advertising Report uses bits 5
and 6 for data status (e.g. truncation or fragmentation), not the PDU
type itself.
The ext_evt_type_to_legacy() function fails to mask these status bits
before evaluation. This causes valid advertisements with status bits set
(e.g. a truncated non-connectable advertisement, which ends up showing
as PDU type 0x40) to be misclassified as unknown and subsequently
dropped. This is okay for most checks which use bitwise AND on the
relevant event type bits, but it doesn't work for non-connectable types,
which are checked with '== LE_EXT_ADV_NON_CONN_IND' (that is, zero).
In terms of behaviour, first the device sends a truncated report:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0040
Data status: Incomplete, data truncated, no more to come
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -98 dBm (0x9e)
Data length: 0x00
Then, a few seconds later, it sends the subsequent complete report:
> HCI Event: LE Meta Event (0x3e) plen 122
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0000
Data status: Complete
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -97 dBm (0x9f)
Data length: 0x60
Service Data: Google (0xfef3)
Data[92]: ...
These devices often send multiple truncated reports per second.
This patch introduces a PDU type mask to ensure only the relevant bits
are evaluated, allowing for the correct translation of all valid
extended advertising packets.
Fixes: b2cc9761f144 ("Bluetooth: Handle extended ADV PDU types") Signed-off-by: Chris Down <chris@chrisdown.name> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Kiran K [Mon, 21 Jul 2025 09:44:37 +0000 (15:14 +0530)]
Bluetooth: btintel_pcie: Fix Alive Context State Handling
The firmware raises an alive interrupt upon sending the HCI_RESET or
BTINTEL_HCI_OP_RESET command. As part of handling the reset command,
firmware initializes the hardware and data path and raises the alive
interrupt. Upon receiving the alive interrupt, the driver must enable
the data path and grant RX buffers to the firmware before sending any
commands.
The alive context maintained in the driver must be updated before
sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race
condition where the context is also updated in the threaded IRQ.
The issue was observed in a stress reboot usecase (1/25) using "sudo
reboot" command where the firmware download was failing as the driver
was not granting RX buffer to firmware due to race condition.
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
Bluetooth: hci0: Boot Address: 0xb0301000
Bluetooth: hci0: Firmware Version: 167-12.25
Bluetooth: hci0: Waiting for firmware download to complete
Bluetooth: hci0: Firmware loaded in 99902 usecs
Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003
new_boot_stage: 0xa0db0003
Bluetooth: hci0: sent cmd: 0xfc01 alive context changed:
fw_dl -> intel_reset1
Bluetooth: hci0: Waiting for device to boot
Bluetooth: hci0: Device boot timeout
Bluetooth: hci0: Firmware download retry count: 1
Fixes: 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware") Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Kiran K [Mon, 21 Jul 2025 09:44:36 +0000 (15:14 +0530)]
Bluetooth: btintel_pcie: Make driver wait for alive interrupt
The firmware raises an alive interrupt upon receiving the HCI_RESET or
BTINTEL_HCI_OP_RESET (Intel reset - 0xfc01) command. This change fixes
the driver to properly wait for the alive interrupt to avoid driver
sending commands to firmware before it is ready to process.
For details on the handshake between the driver and firmware, refer to
commit 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between
driver and firmware").
As the driver needs to handle two interrupts for HCI_OP_RESET and
BTINTEL_HCI_OP_RESET, the firmware ensures that the TX completion
interrupt is always followed by the alive interrupt.
Fixes: 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware") Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ivan Pravdin [Thu, 17 Jul 2025 15:10:52 +0000 (11:10 -0400)]
Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv
Currently both dev_coredumpv and skb_put_data in hci_devcd_dump use
hdev->dump.head. However, dev_coredumpv can free the buffer. From
dev_coredumpm_timeout documentation, which is used by dev_coredumpv:
> Creates a new device coredump for the given device. If a previous one hasn't
> been read yet, the new coredump is discarded. The data lifetime is determined
> by the device coredump framework and when it is no longer needed the @free
> function will be called to free the data.
If the data has not been read by the userspace yet, dev_coredumpv will
discard new buffer, freeing hdev->dump.head. This leads to
vmalloc-out-of-bounds error when skb_put_data tries to access
hdev->dump.head.
A crash report from syzbot illustrates this:
==================================================================
BUG: KASAN: vmalloc-out-of-bounds in skb_put_data
include/linux/skbuff.h:2752 [inline]
BUG: KASAN: vmalloc-out-of-bounds in hci_devcd_dump+0x142/0x240
net/bluetooth/coredump.c:258
Read of size 140 at addr ffffc90004ed5000 by task kworker/u9:2/5844
Zijun Hu [Tue, 15 Jul 2025 14:27:08 +0000 (07:27 -0700)]
Bluetooth: btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
Add one more part with ID (0x28de, 0x1401) to usb_device_id table for
Qualcomm WCN6855, and its device info from /sys/kernel/debug/usb/devices
is shown below:
Zijun Hu [Tue, 15 Jul 2025 12:40:14 +0000 (20:40 +0800)]
Bluetooth: btusb: QCA: Support downloading custom-made firmwares
There are custom-made firmwares based on board ID for a given QCA BT
chip sometimes, and they are different with existing firmwares and put
in a separate subdirectory to avoid conflict, for example:
QCA2066, as a variant of WCN6855, has firmwares under 'qca/QCA2066/'
of linux-firmware repository.
Support downloading custom-made firmwares based on a table newly added.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: btnxpuart: Add uevents for FW dump and FW download complete
This adds uevents which will be generated whenever FW dump is triggered,
FW dump is complete and FW (re)download is done.
This feature is needed for IW612 chipset, which is a tri-radio chipset,
where WLAN runs on CPU1 and BT and Zigbee runs on CPU2.
Currently, whenever BT FW crashes, and FW dump is in progress, there is
no way for 15.4 application to know that CPU2 is in bad state, and when
it will be recovered.
With the help of these uevents and udev rules, the 15.4 app, or any
userspace application can be alerted whenever CPU2 goes in bad state and
recoveres after BTNXPUART reloads the firmware.
Tested this change by creating a simple udev rule to store the
BTNXPUART_STATE value in a ~/<BTNXPUART_DEV>/state file, and running
15.4 traffic.
The 15.4 packets were sent over SPI only when BTNXPUART_STATE was
FW_READY.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As a fix for such scenario, the independent reset vendor command is sent
using the __hci_cmd_send() API, which does not expect any response for
vendor commands.
__hci_cmd_send is non blocking, so before the tx_work is scheduled, it
sometimes gets canceled and 3F|FC command is never sent. Adding a small
delay after __hci_cmd_send allows the command to be sent to the
controller.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pauli Virtanen [Mon, 14 Jul 2025 16:40:37 +0000 (19:40 +0300)]
Bluetooth: ISO: add socket option to report packet seqnum via CMSG
User applications need a way to track which ISO interval a given SDU
belongs to, to properly detect packet loss. All controllers do not set
timestamps, and it's not guaranteed user application receives all packet
reports (small socket buffer, or controller doesn't send all reports
like Intel AX210 is doing).
Add socket option BT_PKT_SEQNUM that enables reporting of received
packet ISO sequence number in BT_SCM_PKT_SEQNUM CMSG.
Use BT_PKT_SEQNUM == 22 for the socket option, as 21 was used earlier
for a removed experimental feature that never got into mainline.
Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Hao Li <lihao1@uniontech.com> Signed-off-by: WangYuli <wangyuli@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
NXP bluetooth chip shares power supply and reset gpio with a WLAN
chip. Add support for power supply and reset and enforce powerup
sequence:
- apply power supply
- deassert reset/powerdown
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com> Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Yang Li [Tue, 1 Jul 2025 07:56:22 +0000 (15:56 +0800)]
Bluetooth: hci_event: Add support for handling LE BIG Sync Lost event
When the BIS source stops, the controller sends an LE BIG Sync Lost
event (subevent 0x1E). Currently, this event is not handled, causing
the BIS stream to remain active in BlueZ and preventing recovery.
Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for 4000000 as secondary baudrate.
This value is selected from device tree property "max-speed"
which is then used to download FW chunks, and as operational baudrate after
HCI initialization is done.
Earlier, the secondary baudrate was fixed to 3000000 in driver, but now
with "max-speed" property, this secondary baudrate can be set to 4000000.
The secondary baudrate is set by the driver by sending a vendor command
(3F 09) to the firmware, with secondary baudrate parameter, in
nxp_post_init().
Any other value set for max-speed other than 3000000 or 4000000 will
default to 3000000, which is supported by all legacy and new NXP chipsets.
This feature is applicable for all new V3 bootloader chips and w8987 V1
bootloader chip.
This property does not apply for w8997 compatible device, since it
downloads a helper.bin FW file that sets secondary baudrate as 3000000
only.
The switch to 4000000 baudrate is validated using a Saleae Logic Analyzer
and imx8m-mini with AW693 M.2 module.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate
Add support for 4000000 as secondary baudrate for NXP chipsets
supporting max baudrate as 4M, and are close to the host processor on
same PCB. This mainly helps with faster FW download.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
projects / thirdparty / linux.git / log
