John Crispin [Sun, 30 Mar 2014 10:02:30 +0000 (10:02 +0000)]
lntiq: add support for Astoria ARV7519RW.
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
John Crispin [Sun, 30 Mar 2014 09:16:52 +0000 (09:16 +0000)]
lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40328
John Crispin [Sun, 30 Mar 2014 09:16:47 +0000 (09:16 +0000)]
busybox: backport dd conv=swab from 1.22
Some boards have the WLAN EEPROM stored in flash in big-endian format,
whereas the driver requires the EEPROM in little-endian format. The
conv=swab option in dd is particularly useful in this case. This patch
backports this feature from busybox-1.22 based on the following commits:
John Crispin [Sun, 30 Mar 2014 09:16:39 +0000 (09:16 +0000)]
ltq-adsl-mei: improve memory allocation
The ltq-adsl-mei driver allocates memory for the ADSL firmware in a
rather stupid way, leading to several 128k allocations, which fail when
many services are enabled. This patch tries to allocate 64 kiB chunks,
and only falls back to larger allocations if the returned pointers are
not correctly aligned. Fixes out-of-memory errors on Danube boards with
32 MiB RAM.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 40325
John Crispin [Sun, 30 Mar 2014 09:16:35 +0000 (09:16 +0000)]
lantiq: fix mtd_split for brnboot firmware images
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
John Crispin [Sun, 30 Mar 2014 09:16:06 +0000 (09:16 +0000)]
lantiq: add support for ZyXEL P2812HNUFX
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com> Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
John Crispin [Sun, 30 Mar 2014 09:15:46 +0000 (09:15 +0000)]
lantiq: xrx200: fix duplex
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
John Crispin [Sun, 30 Mar 2014 09:15:20 +0000 (09:15 +0000)]
kernel: export gluebi info to sysfs
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
John Crispin [Sun, 30 Mar 2014 09:15:16 +0000 (09:15 +0000)]
kernel: rtl8306: fix vlan support on lantiq ar9 p2601hnfx
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
John Crispin [Sun, 30 Mar 2014 09:15:07 +0000 (09:15 +0000)]
kernel: rtl8306: cosmetic changes for swconfig
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Felix Fietkau [Sat, 29 Mar 2014 17:05:35 +0000 (17:05 +0000)]
dropbear: add options SSHKeepAlive and IdleTimeout.
Without timeout mechanism, if ssh client disconnected without sending
FIN or RST, forked dropbear servers would hang there for
KEX_RETRY_TIMEOUT seconds (8 hours).
TCP keepalive is not implemented in dropbear yet, thus the name
SSHKeepAlive.
300 seconds in this patch is selected from the default value of
ServerAliveInterval for Debian ssh client (See man ssh_config).
Jo-Philipp Wich [Fri, 28 Mar 2014 16:05:46 +0000 (16:05 +0000)]
mac80211: skip antenna gain when compiling regdb.txt (#15397)
The antenna gain attribute has been removed from the upstream regulatory database.
Incorperate patch from Luis R. Rodriguez to skip the parsing of the gain attribute
in genregdb.awk in order to emit proper rules again.
Gabor Juhos [Thu, 27 Mar 2014 06:36:47 +0000 (06:36 +0000)]
ar71xx: add user space support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network] Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Gabor Juhos [Thu, 27 Mar 2014 06:36:46 +0000 (06:36 +0000)]
ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ] Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
projects / thirdparty / openwrt.git / log
